SARCO, INC.

A2
SARCO, INC.
50 Hilton Street, Easton PA 18042
www.e-sarcoinc.com / www.sarcoinc.com
610.250.3960 Fax: 610.250.3961
Phones Open: Mon - Fri, 8:30am – 5:00pm
Showroom Open: Monday - Saturday,
E-mail: sarcopa@sarcoinc.com
10:00am – 5:00pm, Friday til 8:00pm
M4 16" COMPLETE BARRELED FLAT TOP UPPER ASSEMBLIES
We have done the hard work for you. These are
fully assembled upper halves complete and
ready to drop on to your complete lower.
All parts made in the U.S.A.! Includes Flat Top Upper, barrel assembly, complete bolt
and carrier assembly, charging handle assembly, forward assist and ejection port
cover assembly...............................................................................$359.00 AR013
Add ons: Kit with carry handle, rear sight assembly....................... $389.00 AR014
Add ons: Lower parts kit and collapsible stock and carry handle.... $449.00 AR117
!!! MARKET BUSTER PRICES !!!
Check our 2 AR pages for many of the best prices
you’ll ever see on AR Kits, Accessories & Major Components! We’re bulging at the seams with AR stuff &
you are the winner at these great prices.
AR15 LOWER RECEIVER PARTS SET
(Includes all parts shown except the receiver) AR15 Type (SemiAuto) Grips not included....................................$89.95 AR001
Our hammer & trigger pin diameter is the industry standard
.154. Some Colt made guns use .170 which is not compatible withour parts.
Includes pistol grip. SALE!!......................................... $49.95, 3 for $140.85
AR15 BARRELED FLAT TOP UPPER RECEIVER ASSY.
16 inch barreled upper receiver with forward assist, ejection port cover,handguards,swivel , front sight and flash
hider. Just add your bolt,carrier and charging handle
and you’re ready to go.......................... $259.95 AR419
AR15 PISTOL CONVERSION, 9MM
UPPER BARRELED RECEIVER SET
Complete upper flat top receiver w/bolt
assy, mag block & 20rd 9mm magazine
ready to add to your lower receiver. This
is for making the AR pistol and it’s a hot
commodity on the AR circuit. Very limited
number in stock. All NFA rules apply
........................................$595.00 AR421
(See our conversion set on page B)
*In areas with restricted magazine capacity,
we can sell you the kit and deduct $15.00 for
the magazine.
9MM AR-15 CONVERSION SET
Consists of a complete upper flat top barreled
receiver with a rail gas block in place of the
front sight, custom flash hider, mag well adapter and 30 rd. magazine. (Deduct $15 from kit
if you live in a state where you cannot have the
magazine). Flash hider is permanently attached
to the barrel. Made in the USA. $595.00
AR395
(This kit comes with a hi capacity magazine.
Please consult your local laws before ordering. If you live in a
state restricting this magazine, we can prorate the cost of the kit
as per the description above.) Last minute addition!
M16 BURST CONTROL KIT
NEW!
ITEM
Parts required to turn a full auto M16 into a 3 round burst
rifle. We’ve been hunting for these for some time
and finally got a few dozen! Kit is composed of
9 parts which include: trigger, hammer, hammer spring, burst disconnector, semiautomatic
burst disconnector, 2 disconnector springs, 3
shot cam, cam spring. Comes with modification
instructions.............................. $59.95 AR415
SARCO DOES IT AGAIN!
Smashing Unheard Of Price Breakthrough On
AR15 PARTS SETS!
Double time it and get these before they’re
gone..... Everything present in this Kit to
make an AR15 type rifle except for the Lower
Receiver. All parts included are a combination of USGI and commercial new manufacture parts. Sling and magazine are
not included. Buttstock supplied is
the telescoping 6 position M4 stock
with correct buffer and spring and
the 16” barrel is brand new and has
the front sight assy. installed. We
use the industry standard hammer/
trigger pin with a diameter of .154”:
Most Lower receivers use this size
Barrels with these kit are the
pin although there are some Colt
desirable Wylde design .223
mfg. lower receivers that use .170" pins which are not
/ NATO 5.56 barrels! Perfect
compatible with standard parts. The Upper Receiver
for commercial .223 and
is a flattop model and we offer it with and without the
NATO 5.56 ammo!
carry handle/rear sight configuration.
A. KIT w/ Flat top upper rec. w/ carry handle and rear sight.................. $429.00,
3 for..................................................................$1260.00 AR150 (shown in picture)
B. KIT w/ Flat top upper rec. without carry handle & rear sight
.............................................................................................................. $409.00,
3 for............................................................................................$1199.00 AR224
COMPLETE UPPER KIT FOR OUR AR-RETRACTABLE STOCK CARBINE
As shown above all parts but lower receiver parts
and buttstock assy parts $365.00, 3 for
$1079.00 AR335 This is the flat top upper with
detachable handle.
PLEASE NOTE: Building an AR-15 requires technical
skills. Be sure you are qualified before you build
or seek a professional gunsmith.
New production m16A1 20" barrel with barrel extension, without front sight
base – not drilled for gas port hole. From a premier U.S. barrel maker. 1 in
12" twist...........................................................................$145.00 AR201
CRIMSON TRACE LASER GRIPS
Best low profile laser device for pistols on
the market!
We’ve got a great deal on brand new Para
branded, Model LG404 Crimson Trace
Laser Grips for use with the following
pistols:
PARA Compact and single stack
COLT Officer’s & Defender
KIMBER Compact,Ultra Carry & Ultra Elite
SPRINGFIELD ARMORY Compact & Ultra Compact
WILSON COMBAT …. And other auto pistols with
grip screws measuring 2-11/16" apart.
Grips come with batteries, internal grip dust shims,
Allen wrenches for laser alignment, laser label &
swabs. Simple to install and use. Most importantly,
it provides an upgrade to your pistol that does not
change the gun’s sleek appearance or handling
characteristics. On/Off switch on bottom left grip
and activation button set on the grip where the
middle finger rests. Color-Black. Limited supply
in stock and priced to move
$249.95 GRP206
$175.00 PRICE BUSTER!!!
Compare Elsewhere!
AR15/M16 RIFLE PARTS
AM136 223 (5.56) Dummy Rounds from Lake City –
Original G.I. green tip................. 10 for $8.95
AR098 AR Safety...........................................$10.95
AR100 AR15 Disconnector.............................. $9.95
AR092 AR15 Hammer (Semi auto).................$15.00
AR001 AR15 Lower Receiver Parts Kit (SemiAuto)..................................................$49.95
AR102 AR15 Trigger (Semi-Auto)...................$17.95
AR082 AR15/M16 Action Spring..................... $4.00
AR120 AR15/M16 Action Spring (shorty style).$4.00
AR032 AR15/M16 Barrel nut.......................... $7.50
AR162 AR15/M16 Bipod Pouch New G.I. (nylon)
............................................................ $4.95
AR138
AR15/M16 Bipod with new canvas G.I. zipper
pouch with accessory pouch on side..$13.50
AR137 AR15/M16 Bipod w/ O.D. Green Nylon pouch
..........................................................$12.50
AR322 AR15/M16 Bipod w/o Pouch, used...... $9.95
AR060 AR15/M16 Bolt Cam Pin...................... $6.00
AR071 AR15/M16 Bolt Carrier Key...............$13.50
AR070 AR15/M16 Bolt Carrier Key Screw....... $1.00
AR106 AR15/M16 Bolt Catch.......................... $7.50
AR105 AR15/M16 Bolt Catch Pin.................... $1.00
AR107 AR15/M16 Bolt Catch Plunger............. $7.50
AR108 AR15/M16 Bolt Catch Spring............... $1.00
AR057 AR15/M16 Bolt gas rings, set of 3........ $3.00
BRUSH-003 223 cal bore brushes, bronze 10 for
............................................................ $8.95
AR080 AR15/M16 Buffer .............................$12.95
AR081 AR15/M16 Buffer Short.....................$12.95
PROJECT BARRELS FOR THE RUGER® 10/22®
!
SALE
Sarco brings you a terrific selection of new barrels for your
Ruger® 10/22® firearms project. We offer 4 caliber selections.
In some cases, these barrels just need to be polished and crowned on the
muzzle end. A few will need other finishing touches. Compare at $99.00.
See notes below:
1. .17 caliber HM2 SS, 18 inches long 920 O.D. Ready to Go!
.................................................................................................................... $65.00 RGR007
2. .17 caliber HM2 4140, 24 inches long 920 O.D. needs to be polished and crowned
.................................................................................................................... $50.00 RGR008
3. .17 caliber HM2, 4140, 18 inches 920 O.D. Ready to Go!............................. $50.00 RGR009
4. .17 caliber HM2 SS, 20 inches long 920 O.D. needs to be polished and crowned
.................................................................................................................... $50.00 RGR010
5. .22 caliber Magnum, 4140, 24.5 inches long 920 O.D. needs to be polished and crowned
.................................................................................................................... $50.00 RGR003
6. .22 caliber Magnum, SS, 18 inches long 920 O.D. needs cuts for the extractor & barrel lock
block............................................................................................................ $35.00 RGR005
7. .17 caliber HMR SS, 18.25 inches long 920 O.D. needs to be polished and crowned
.................................................................................................................... $50.00 RGR006
PLEASE NOTE: .17 HMR is for 10/22 Magnum rifles only! This is not a recommended conversion as
you would need a heavy bolt and heavy recoil spring. Chamber pressure is too great and is problematic in
semi autos. This is only for the advanced gun builder and when assembled, should be carefully checked
by a qualified gunsmith.
*****.17 HM2 REQUIRES USE OF A HEAVY BOLT.
*****.22 MAGNUM- REPLACEMENT FOR ORIGINAL GUNS ONLY. WILL NOT FIT THE 10/22 LONG RIFLE
AR087 AR15/M16 Buffer Retainer................... $2.00
AR088 AR15/M16 Buffer Retainer Spring....... $1.00
AR306 AR15/M16 Buttstock hinged trapdoor assy
............................................................ $9.95
AR307 AR15/M16 Buttstock trapdoor hinge
.............................................................. $4.00
AR119 AR15/M16 Butt Swivel A1/A2............. $4.00
AR056 AR15/M16 Butt Swivel Pin................... $1.00
AR118 AR15/M16 Butt Swivel Screw M16A2... $2.85
AR002 AR15/M16 Charging Handle assy......$16.95
AR188 AR15/M16 Cleaning Toothbrush, G.I.
......................................$2.00, 3 for $3.75
AR164 AR15/M16 Comb. Wrench (Original G.I.)
..........................................................$16.95
AR104 AR15/M16 Disconnector Spring........... $1.00
AR178 AR15/M16 Early prong flash hider.....$12.50
AR036 AR15/M16 Ejection Port Cover............. $7.95
AR034 AR15/M16 Ejection Port Cover Snap ring
............................................................ $1.00
AR035
AR15/M16 Ejection Port Cover Spring.....$1.50
AR172 AR15/M16 Ejection port cover pin....... $2.75
AR067 AR15/M16 Ejector............................... $3.00
AR066 AR15/M16 Ejector Pin......................... $1.00
AR068 AR15/M16 Ejector Spring.................... $1.00
AR064 AR15/M16 Extractor..........................$10.95
AR063 AR15/M16 Extractor Pin...................... $2.00
AR065 AR15/M16 Extractor Spring................. $1.00
AR059 AR15/M16 Firing Pin........................... $7.95
AR058 AR15/M16 Firing Pin Retaining........... $2.00
AR011 AR15/M16 Flash Hider Washer............ $1.00
AR049 AR15/M16 Forward Assist, Teardrop type
..........................................................$21.50
AR047 AR15/M16 Forward Assist Pin............. $1.00
AR048 AR15/M16 Forward Assist Spring........ $1.00
AR077 AR15/M16 Front and Rear Takedown Detent
Spring.................................................. $1.00
AR078
AR15/M16 Front and Rear Takedown Detent
............................................................ $1.00
AR079 AR15/M16 Front Pivot Pin................... $4.95
AR020 AR15/M16 Front Sight Detent............. $2.00
AR021 AR15/M16 Front Sight Detent Spring.. $1.00
AR024 AR15/M16 Front Swivel Pin................. $1.00
AR023 AR15/M16 Front Swivel Rivet.............. $1.00
AR029 AR15/M16 Gas Tube 16" (Shorty)......$11.95
AR028 AR15/M16 Gas Tube 20" (Standard)..$13.50
AR027 AR15/M16 Gas Tube Pin..................... $1.00
AR072 AR15/M16 Grip Screw & Washer......... $1.00
AR089 AR15/M16 Hammer Pin....................... $1.50
AR093 AR15/M16 Hammer Spring.................. $2.00
AR275
M16/M16A1 Handguard, new Colt (Right)
..........................................................$14.95
AR005 AR15/M16 Handguard (Right) Used $10.00
AR025 AR15/M16 Handguard Cap (Triangular)
............................................................ $6.95
AR033 AR15/M16 Handguard Slip Ring (G.I).. $7.50
AR030 AR15/M16 Handguard Snap Ring........ $2.50
AR031 AR15/M16 Handguard Spring.............. $6.00
AR083
AR15/M16 Lower Receiver Extension.$20.00
AR165 AR15/M16 Mag Carrier........................ $1.50
AR109
AR15/M16 Magazine Catch.................. $7.50
AR200 AR15/M16 Magazine Catch Assembly.$10.00
AR177 AR15/M16 Magazine Catch Button, metal
............................................................ $2.50
AR111
AR15/M16 Magazine Catch Spring....... $1.00
BUILD AN AR15
FROM A KIT!
A fabulous DVD video with
all you need to know for
your AR project.
AR367................... $39.95
AR368 Special with any one
of our AR15 kits
............................ $31.95
M1A1 STOCK FOR RUGER® 10/22®
IN STOCK!
Hot off the wood mill, we’ve got the best
stock to trick out your fine 10/22® rifle.
Simply insert your barreled action into Sarco’s stock assy, and within
minutes you have a version of the 10/22® that closely resembles and
handles like a U.S. Paratrooper M1A1 Carbine! Comes complete with handguard and
swivel band assy. Looks great, and with a folding stock, you will benefit from the versatility of use and easy storage! Beautifully made hardwood stock, handguard, and metal &
leather folding stock assy, are sure to convince friends that you have a real .30 cal. M-1
Carbine. Makes one of the world’s best .22 rifles even better!.............. $149.95 STK380
SARCO’S M-1 CARBINE STOCK CONVERSION FOR THE RUGER® 10/22®
Ruger® 10/22® rifles are a great platform for making all sorts of custom hunting, target, and military
configuration rifles. We like it just the way it is, but
Sarco Stock
now we have constructed a new way to enjoy this
dependable firearm. Sarco, Inc. has created the M-1
Carbine stock specifically made to drop the 10/22®
This is what you don’t get.
Our stocks are authentic
rifle into without any alteration! That’s right! No
M1 Carbine.
alterations! The front sling swivel is also properly installed like the USGI M1 Carbine. Others stocks on the market do not have this accurate
feature. The wood grain/finish mimic the Tung Oiled finish of the Govt. Carbine stock.
This fine stock comes with matching wood handguard, steel buttplate, M1 Carbine front
band, M1 Carbine sling and oiler........................................................... $99.95 STK340
(This is a SARCO, INC. product for use with the 10/22®)
AR126 AR15/M16 Magazine Orlite (30 Round)
................................................ $11.95 each,
AR163 AR15/M16 O.D. Web Case w/ Pouch.$17.95
AR133 AR15/M16 Pin Kit..............................$14.95
AR043
AR15/M16 Rear Sight Aperture, Standard
............................................................ $5.00
AR039 AR15/M16 Rear Sight Detent............... $2.00
AR040 AR15/M16 Rear Sight Detent Spring......$1.00
AR038 AR15/M16 Rear Sight Drum................ $6.50
AR037 AR15/M16 Rear Sight Drum Pin.......... $1.00
AR046 AR15/M16 Rear Sight Spring............... $1.00
AR041 AR15/M16 Rear Sight Windage Screw.. $7.50
AR115 AR15/M16 Rear Takedown Pin............ $5.75
AR050 AR15/M16 Round Forward Assist
..........................................................$14.75
AR130 AR15/M16 Rubberized Swivel front new.$5.00
AR076 AR15/M16 Safety Detent..................... $2.00
AR075 AR15/M16 Safety Detent Spring.......... $1.00
AR171 AR15/M16 Scope Mount Rings............ $6.95
AR095 AR15/M16 Sear Assembly..................$20.00
AR116 AR15/M16 Sear Spring........................ $3.00
AR145 AR15/M16 Shorty Buttstock Assembly, high
strength fiberglass w/steel locking ring
..........................................................$29.95
AR134 AR15/M16 Spring Kit........................$12.95
AR302 AR15/M16 Top sling adapter............... $1.95
AR090 AR15/M16 Trigger Pin......................... $1.50
AR103 AR15/M16 Trigger Spring.................... $2.00
AR176 AR15/M16 Triggerguard, aluminum.... $6.75
AR112 AR15/M16 Triggerguard Pin................ $1.00
AR006 AR15/M16A1 Birdcage Flash hider
............................................................ $6.95
AR085 AR15/M16A1 Buttcap Screw (Short).... $2.25
AR220 M16A1 Butt Swivel Screw.................... $3.00
AR018 AR15/M16A1 Frong Sight Post............. $5.00
AR142
AR15/M16A1 G.I. Buttstock w/trap plus lower
receiver extension, buffer, & spring....$59.95
AR073 AR15/M16A1 Pistol Grip (Used).........$12.50
AR228 AR15/M16A1 Complete Rear Sight Set
..........................................................$20.00
AR157 AR15/M16A1 Sight Tool (5 Prong)........ $4.95
AR214 AR15/M16A2 Burst Trigger...............$15.00
AR143 AR15/M16A2 Buttstock (Current production)
milspec..............................................$39.95
AR007 AR15/M16A2 Flash hider.................... $8.95
AR144 AR15/M16A2 New Buttstock (Current
production) stripped...........................$34.95
AR074 AR15/M16A2 Pistol Grip new............... $8.95
AR158 AR15/M16A2 Sight Tool (4 Prong)
............................................................ $4.90
AR091 M16 Hammer.....................................$15.00
AR127 M16 Magazine 6 Orlites w/ Carriers
..........................................................$59.95
AR317 M16 port firing gun safety plate – new G.I. in
package.............................................$24.95
AR399 M16A2 Buttplate used good
................................. $3.95, 10 for $29.95
AR358 M16A2..Peel off flash hider washers. Used take
off. Work fine....................................... $7.95
AR205 AR15/M16 chamber brush
.................................................... 2 for $3.95
AR141 M16 Original G.I. Buttstock, plus lower receiver
extension, buffer and spring
..........................................................$59.95
B2
SARCO, INC.AR15 AND M16 PARTS AND ACCESSORIES
BRITISH 19TH CENTURY ‘SLADE
WALLACE HARNESS’ SET
50 Hilton Street, Easton PA 18042
www.e-sarcoinc.com /
www.sarcoinc.com
610.250.3960 Fax: 610.250.3961
From Islandlawana,
the road to Kabul,
with Kitchner to
Khartoum and far
east of Istanbul…
for the Opium War,
the stalwart British
soldiers carried the
most important
supplies on their
harnesses. This late
model 1888 ‘Slade
Wallace’ load bearing harness is ruggedly constructed to
handle the weight
of rechambered .303 Martini Rifle and Enfield
.303 ammunition and the bayonet. It is beautifully crafted with solid brass hardware and
‘S’ shaped ‘goose head’ buckle and individual
bullet loops in the cartridge boxes
........................................ $124.95 MISC388
AR15 / M4 “MELONITE” TREATED
BARREL
E-mail: sarcopa@sarcoinc.com
AR15 FIXED STOCK 'COLLAPSIBLE
LOOK-A-LIKE'
For all of the
Americans who live
NEW!
in the few states
ITEM
where an AR15 Collapsible Buttstock
is not allowed, (go figure!), we are now able
to offer a well-made solid stock that provides
the appearance of the military M4 collapsible
stock. Made from aluminum and composites,
it has a length of @11 inches and weighs 1.15
lbs. Comes with tube locking ring and sling
swivel. Black color................ $39.95 AR410
AR15/M16 UPPER
RECEIVER VISE BLOCKS
To securely hold your upper
firmly without damage to the
upper or the barrel on barrel
installation. Will work on
any AR upper (receiver not
included.)......................$29.95 AR-VICE
SPECIAL ON BURST CAM
SPRINGS FOR THE M16A2
We got a deal (we used to pay $3 ea. in
quantity) 3 for.......................... $10.00,
10 for...................................... $20.00,
50 for...................................... $75.00,
100 for......................... $100.00 AR360
SUPER FIND!
SARCO can
offer you
a superior
NEW!
16" AR barrel with 1 in 7 twist. Melonite
ITEM
treatment means that the barrel has
greater corrosion resistance, and surface hardening due to a process that covers and impregnates
the metal, but does not change the dimensions like
the chrome process does. Ballistically , this is an
advantage, because it is recognized that chroming
can change accuracy by way of coating deviations
and failure to equally distribute chrome during the
application process. Melonite essentially provides
the durability of chrome while maintaining the
accuracy of an un-plated barrel, all in the quest for
longer barrel life......................... $135.00 AR226
Just got a great buy on Bushmaster 16½" M4 BARRELS CHROME
LINED. We’ll pass the deal on to you
$139.95 AR406
P-1882 MARTINI HENRY BANDOLIER
British 50 rd. bandolier created during
the Zulu Wars to help mounted troops
deal with unpleasant situations like being
overrun at Isandlwana and hanging by the
skin of their teeth at Rorkes Drift because
ammunition issue was challenging.
Ruggedly made and stitched to hold 50
rounds of 577/.450 Martini ammunition.
(Also holds shotgun ammo 24 ga – and
can be softened to hold 12 ga rds in most
holes accept where the fasteners are). Has
strap to fasten to a waist belt for a secure
fit. Three of these make a ‘rough riding’
cross chest & waist Pancho Villa style set!
Very thick brown leather with brass hardware. Although it is meant as an over the
shoulder bandolier, it is also a comfortable waist belt bandolier fitting up to a
45" waist.
M4 stock set with handguards &
pistol grip............... $50.00 AR316
New M16A2 or M4 pistol grip
................................ $8.95 AR074
5.56MM/.223 BROKEN SHELL
EXTRACTOR
Brand new tool;
made for removing stuck headless cases
from the chamber of any .223/5.56mm
rifle. We’ve never seen these offered
before now..................BSE001 $5.95 ea.
Our new BSE’s work – others on the
market don’t fit. We learned the hard
way!
We found a “few” M16 G.I. slings, new –
in their original Colt marked bag, sealed
– Great for Colt or M16
collectors.................... $14.95 SLNG092
OVER STOCKED OR BURIED IN AR/
M16 PARTS AFTER THE CRASH?
We will buy up bulk lots of these
parts - Call or email Dave
mgdave@sarcoinc.com
Note: We have recently spent over
$200,000 on AR parts clean outs
AR15 SLING PLATE (Metal) Single
point sling mount for collapsible
stock. AR mounts between lower
receiver. Quality steel construction. Use with our AR15 Single
Point Sling (LA032)..............$9.95 LA030
AR15/M16 CHAMBER BRUSH
Original style............................2 for $3.95 AR205
AR 16" BARREL GAS TUBES
Just got a shipment in. these have been tight
.................................................$11.95 AR029
M16 COMBINATION WRENCH
Late style tool for removing
flash hiders, barrel nut, and
buffer tube. Has cut out to
attach torque wrench or standard socket wrench. If you plan on removing the
barrel on your AR15/M16 you’ll need one of these
wrenches. Original G.I., New........... $16.95 AR164
COMPLETE BOLT CARRIER
ASSEMBLED
$125.00, M16 AR264 AR15 AR263
3 for $360.00
SPECIAL SALE!
$110.00, 3 for $299.00
IT’S A SALE ON SALE!!
$99.95, 3 for $285.00
SIGHT ADJUSTING TOOL
“Old style” AR15/M16 for
round front sight.
$4.95 ea.
AR157
AR “MINI SCOPE” RISERS!
NEW!
ITEM
Well-made machined from
aircraft aluminum, this set
of black Picatinny risers
will let you add height to
your scope mounting on a flat-top AR or on
other guns where a Picatinny rail is mounted.
Each riser is 1-1/4" long , 3/4" in height. Fits
all Picatinny or Weaver rails! Finely made by
Bushmaster. $19.95 AR409
AR SCOPE / LEATHERWOOD MOUNT
Aluminum scope
mount for AR Upper
with handle. Accepts
Weaver style scope
rings or accessories.
Easily attaches in 30
seconds.
$9.95 AR417
ONLY
$54.95
MISC334
M16 ACCESSORY KIT - HEAVY DUTY
AR15 ACCESSORIES
Cleaning rod 4 pc. CLN030............................ $6.95
Muzzle Cap (plastic) AR192..... $1.50, 3 for $2.75
Stripper clip guide STC005............................. $1.50
Magazine dust covers AR199................. 3 for $2.00
M16 G.I. cleaning “toothbrush” orig. G.I. issue.
AR188.....................................$2.00, 3 for $3.75
SPECIAL - one each of all 5 items above.
AR321........................................................... $8.95
M16A2 PEEL OFF FLASH HIDER WASHERS
AR358...................................$7.95, 3 for $18.95
AR DELTA RING REMOVAL TOOL Makes handguard
removal simple AR326................................... $8.95
Cleaning toothbrush (GI)
Silent sling, Front sight tool
Muzzle cover, Magazine dust covers (6)
Combo wrench, Plastic mag carriers (4)
(Israeli G.I.), Broken shell extractor
Bipod, Cleaning rod, Stripper guide
2 Grenade launcher tension band (rare)
AR15/M16 CLEANING KIT
& ACCESSORY KIT
1.M16A1 $6.95 AR006
2.M16A2 $8.95 AR007
3.Early 3 prong type
flash hider $12.50 AR178
Not for sale in NJ
• Bore brush
• Cleaning rod
• Tooth brush
•Oiler
• Muzzle cap
• Dual front sight tool
AR /M16 ARMORER'S KIT
$17.50, 3 for $49.95 AR240
for just AR373
$59.95
AR15/M16 TEAR DROP FORWARD ASSIST
Available again! New, Few only $19.95 AR049
ORIG. G.I. M16 BIPODS
New G.I. bipod in wrap AR139........................$14.95
Used exc G.I. bipod AR322................................ $9.95
New nylon G.I. pouch AR162............................ $4.95
.233 CAL BORE BRUSHS
bronze 10 for $8.95 BRUSH-003
OUR LATEST BUY – GREAT DEALS 9MM
(x19) PARABELLUM CARBINE (16") &
PISTOL BARRELS (10½")
For Your 9mm AR Project 9mm AR Pistol and Carbine barrels. We just
bought an over run of 9mm barrels in 10 ½" and
16" lengths. Barrels are 1-14 twist and fully machined and chambered. These barrels are in the
white and ready to take the finish of your choice.
These have threaded muzzles (1½" x 36 thread).
These are made by a prime barrel maker. What
a deal!! List on these barrels from the source is
$170-$180! 16" AR319, 10½" AR332
Originally $99.95, $64.95, 3 pcs/$179.95,
10 pcs/$575.00
• Chamber brush
• Broken shell
extractor
• Stripper clip guide
• Grenade launcher
Tension band
AR-15 DUAL FRONT SIGHT TOOL
Two-in-One tool with dual functions to adjust
both 4-prong and 5-prong front sights. Makes
adjusting the front sight on your A1 and A2 a
snap. $5.95, 3 for $14.95 AR175
AR15 LONG FLASH HIDER FOR M4 CARBINES
51/2" long screws on like the short one
Not for sale
in NJ
with slots $19.95 AR213
with holes $19.95 AR212
AR15 & M16 MAGS
Orlites & Orig Colt & others – See
our e-sarcoinc.com for sales on these
items
NEW M16A2 ROUND HANDGUARD
SETS MILITARY PRODUCTION
Shortie length
w/liner $14.95 AR185
AR SHORTY BUTTSTOCK INSTALLATION
WRENCH
$2.95 Free Bonus –
other end of wrench fits
the 1911 barrel bushing TOOL031
JUST GOT IN 1000 AR BOLT
CARRIERS
Can sell at old time
prices… $49.95 AR069
A favorite of Contractors and
Operators in front line work. Heavy duty,
simple to use, with hardware that can take
the punishment of undue weight changes,
NEW!
ITEM
friction, and abuse of combat environments.
Easy to lengthen and shorten. Overall extended length is 38" and can be
reduced to 26.5 inches. Bottom connecting straps are bungee expansion
type w/ Cordura nylon covers. Shoulder strap is the preferred 2-3/8" wide
nylon..................................................................................$12.99 each
Available in 3 colors: SLNG099-Black, SLNG100-Green, SLNG101-Scorched
Dark Earth
AR15/M16 SPRING KIT
A set of all of the coil & torsion springs
in the AR15 or M16. Ideal item for your
spare parts box. Price if bought separately $18.30 Kit Price only. Includes
recoil springs
Shortie M4 Kit.................$12.95 AR134
3 for.......................................... $32.95
Standard Stock Kit ..........$12.95 AR397
3 for.......................................... $32.95
DESIRABLE 6.8MM SPC AR15
BARRELS
6.8mm SPC AR15 Barrels – We were lucky
to get this over run of AR barrels in 6.8 SPC.
These are 16" heavy barrels and are complete
with barrel extension. Gas port needs to be
drilled before receiving your .750" diameter
gas block or sight base. 1 in 10 twist. Headspaced and ready to go. Threaded muzzle
.............................................$75.00 AR388
10 for............................................$650.00
SPECIAL SALE ON
UPPERS! BEST PRICE EVER!
WE GOT A GOOD BUY!!
AR FLAT TOP A4 UPPERS
Many choices to suit your needs.
A: Stripped flat top upper....... $48.95 AR196
B: Stripped Flat Top Upper with our complete
A-4 carrying handle assy. (includes complete
A2 rear sight assy).................$74.95 AR202
C: Stripped flat top upper with M4 carry
handle assy and also ejection port cover assy
and forward assist assy.......... $94.95 AR204
AR-15 TAPCO INTRAFUSE HANDGUARD SET
Value $83.50
Sarco Special Price $36.95 AR238
FLASH HIDERS
Be ready when the time comes!
Quality tool set for removal &
installation of parts. Easily worth
the cost just for the quality vise
block set! INCLUDES - VISE
BLOCK, DELTA WRENCH, TOOL
BRUSH, GI COMBO TOOL, BROKEN SHELL
EXTRACTOR, BORE & CHAMBER BRUSHES, 2
SIGHT TOOLS, CLEANING ROD SET $91.50 value
NEW!
ITEM
AR SINGLE POINT SLING
New sporting design
makes these 6.5" handguards with 3 accessory
rail covers, a convenient
change of variety for your
M4 style rifle. Color: black
$29.95 AR420
ORIGINAL U.S. AIRFORCE .22
LONG RIFLE CONVERSION UNIT
for more M16 with Teflon magazine-1 or 2
only! Super Rare......................$350.00
ORIGINAL G.I. M16 RIFLE SLINGS
In their original packaging..$8.95,
3 for
$24.95 SLNG087
EXTRA MAGAZINES FOR THE G.I. M261 .22LR
CONVERSION UNIT FOR THE AR15
$24.95 ea. M26120
This is the end of these Send $1.00 for
complete list of our M261 parts (M26122) M261
manual (few only) - $4.95 M26121
See e-sarcoinc.com for a spare parts put-away kit for
the M261 kit
M16 PIN KIT
Front swivel, gas tube, rear sight
drum, forward assist, butt swivel,
firing pin retaining, extractor, ejector,
front pivot, rear takedown, hammer,
trigger, bolt catch, trigger guard, ejection port cover..................... $14.95
3 for..........................$39.95 AR133
M4 AR15/M16 RECEIVER CARRYING
HANDLE AND REAR SIGHT ASSEMBLY
Fits Flat Top Upper reciever with Picatinny Rail.
Complete with M16A2
rear sight assembly.
AR180
SPECIAL SALE!
$29.95,
3 for $84.95
M16 AUTO SEAR
Orig U.S. G.I. exc cond. Few only
...............................$19.95 AR095
Buy a replacement(s) for your legal M16.
All NFA rules apply.
Note: These go out of time with use.
AR-15 LOW PROFILE RUBBER RAIL
COVERS
Rubber composite rail
guards slip on quickly
to both protect unused
Rails and comfort
your hand grip. 6-7/8
inches long, they can be trimmed to size
as needed. Two colors available:
Black rail cover...................$3.75 LA017
Green rail cover................$3.75 LA017G
4 Rail Covers for... $9.95 (mix or match)
M16 BOLT CARRIERS
Just Came In The Door!!.......... $65.00
3 for........................... $180.00 AR229
SPECIAL SALE!
$49.95, 3 for $139.95
Just a few – M16A1 new G.I. composition buttplates. First out are in
military wrap..........$19.95 AR394
*****Original USGI*****
EARLY VIETNAM ERA M-16 STOCK SETS &
TRIANGULAR HANDGUARDS
1. Early Stock without trap door and with rubber
buttplate; good condition / no cracks
................................................ $35.00 AR146
2. Original M16 Pistol Grip..............$9.95 AR364
3. Original Triangular Hand Guard Set
................................................ $35.00 AR318
4. Set of early stock, triangular hand guard set,
and early pistol grip. Good condition, no cracks.
................................................ $69.95 AR255
M16-A1 STOCK SET
5.
6.
Original M16A1 stock with buttplate & swivel
................................................ $37.50 AR411
Complete set of M16A1 stock, triangular
handguards and pistol grip...... $ 69.95 AR412
COLLAPSIBLE AR-15 CARBINE STOCK
$34.95 3 FOR $94.50 AR145
• Six Positions • Precision machined Parts for
Maximum Strength • Super Quality Aluminum
Buffer • Includes complete stock assembly w/
buffer & recoil spring. • Reinforced grids Black (AR145)
HIGH QUALITY AR/M4 CARBINE
LENGTH QUAD RAIL HG SYSTEM
$38.95 AR384
Other sell for up to $150.00 or more
See our bayonet page G for
M16 (M7) bayonets
SARCO, INC.
K2
NEW!!! M14 BARRELS
IN STOCK
50 Hilton Street, Easton PA 18042
www.e-sarcoinc.com /
www.sarcoinc.com
610.250.3960 Fax: 610.250.3961
NEW!
ITEM
Brand new .308 cal M14 Barrels made
by one of the best U.S. barrel manufacturers.
................................... $159.95 each,
or 3 barrels for........... $455.00 M14124
E-mail: sarcopa@sarcoinc.com
Note: See our 1st of the
month ad or our E-com
site for M-14 Magazines.
M14 PARTS & ACCESSORIES
ORIGINAL G.I. TRW M14
RECOIL SPRINGS
Also work of course in all
semi autos. Just in the door..
$7.45,
5/..........................$29.95,
10/............ $49.95 M14052
NM SIGHT & APERTURE BUYERS
PLEASE NOTE:
USGI M14 STOCK ASSEMBLY
Very good condition M14 walnut
stocks with buttplate assembly with shoulder rest and sling
mounts. Can still see the National
Defense cartouche marking. Some
minor dings & blemishes, but overall highly serviceable and the best
we’ve had in years!
.......................... $75.00 M14354
The aperture is made oversized to be
fit to your sight base. The procedure
is simple & instructions are included.
See our website for the instructions
if you wish.
National Match Rear
Sight Aperature
Your choice of .520 or
.595 diameter
$5.95 BSE002
M14/M1A SIGHT
PROTECTORS
Military style plastic snap-on
covers to protect the front and
rear sights and the flash hider
muzzle of the M14/M1A rifle.
New. $6.50, 3 for $17.95
M14022
U.S. Army
Design
M14 RIFLE CLEANING KIT
Kit consists of following items:
G.I. sectional
cleaning rod,Rod
handle/
combination tool
Ratchet chamber
brush, .30 cal. bore brush
G.I. carrying pouch $12.50
3 for $29.95 CLN070
M-14 MILITARY
MAGAZINE POUCH
Original Vietnam era
design as used by
a U.S. ally. Holds 2
M14 Magazines and
can hold 2 grenades
in side slots. Also
has a belt loop on back for fastening.
Very good condition. Pouch only
................................ $9.95 M14020
M14 SPECIAL ITEMS
1. M14 gas cylinder (Chinese)........$29.95 M14108
2. G.I. M14 connector rod.............. $14.95 M14049
.........................................................3/$36.50
3. G.I. front stock swivel set, new.....$8.95 M14117
4. National Match front swivel....................$23.75
5. M14 E2 stock liner set (front grip mounting
kit) G.I. new in package contains liner Grip
hinge base, screws & plugs........... $64.50 M14113
6. New bolt rollers.......................... $4.95 ea M14060
7. M14 bolt with roller, new............. $175.00 M14155
9. M14 bolt roller with retaining clip.....$7.95 M14352
10. M14 bolt roller retaining clip.............. 3.95 M14158
See our website for other M14 parts
Found a few more...
M14 G.I. “SPOTTY BOLTS”
Out of parade rifles – Spot weld in firing
pin hole and rear – last of the 1000 we
had. $39.95 M14147 While the few last
NEW G.I. SPEC M14 & M14A
BOLTS WITH ROLLER
These are New production
Rockola forged bolts to original
GI blueprint and heat treat. 8620 H
Steel/#719-0185 GI print. Heat treat spec
A-Z-2M47512. Fully Military compliant
part check the TALK boards....$175.00
M14155 (ORDER EARLY THESE WILL FLY OUT)
.30-06 and .308 caliber
barrels in stock !
Newly manufactured barrels ready to install on your M1 Garand Receiver. Made
by one of the premier barrel manufacturers in the USA, these .30-06 caliber
barrels and .308 barrels are manufactured from 4140 steel with 4 groove
rifling and a 1 in 10 twist. Beautiful
high quality parkerized replacement
barrels. Because they are made here in
the US, they do not have the ungainly
import barrel markings. A great chance
to get rid of that ‘Blue Sky’ or other
import marked barrel and also restore
accuracy! Barrels should always be
installed by a qualified gunsmith.
.30-06.....................$159.95 GRD157
.308.........................$159.95 GRD158
Mix or Match 3/......$455.00 GRD337
Please specify when ordering
M14 STRIPPER CLIPS
7 original clips for $9.95 STC016
M14 FLASH HIDERS W/BAYO LUG
In stock again! New Production
$29.50 M14079
ORIGINAL G.I. M14 BUTTPLATE SETS
Complete buttplate & the 2 screws
........................................$24.95 M14143
M14 7.62 NATO CHAMBER BRUSHES
G.I. ratchet chamber brush
originally made for use with
the M14 rifle, but will work just as well in most
7.62mm NATO rifles, new.................... $2.95
or 3 for................................... $6.95 M14016
M1 GARAND - MORE ON PAGE D
WWII M1 GARAND RIFLE
LEATHER SCABBARD
These leather scabbards were used by horse
cavalrymen and truck and jeep drivers.
These heavy leather scabbards have the
tunnel to cover the operating rod handle
and two leather carrying straps with brass
hardware. Perfect reproduction.
SALE $59.95 each
GRD137
Original G.I. new sling keepers for
Springfield and Garand 1907 leather
slings – buried for years. $5.95 ea,
2 for $9.95 SLNG067
Available Again – Ratchet
chamber brushes for the
M1 Garand… $4.95, 3 for $9.95
.30-06 cal TOOL044
M1D BARREL WITH MOUNTED SCOPE BLOCK
M14 FLASH HIDER PLIERS
Just in, new M1D Garand barrel ready to install
and mount your scope............. $249.00 GRD159
Available once again. New condition. A
necessity for your M14 ensemble
$16.50 ea. TOOL039
$39.95 M14127
7.62MM BROKEN SHELL
EXTRACTOR
Brand New…. M1
GARAND BARRELS…
Brand New
M1D GARAND SNIPER RIFLE KIT
A REALIZED DREAM FOR SARCO &
OUR VALUED CUSTOMERS!
Convert your M1 Garand into a
military grade M1D Sniper Rifle or
build your own M1D with our M1D
Garand kit which includes a new
M1D Barrel with mounted scope
Block, Scope ring mount, T37 flash
hider, M84 scope with rubber eye piece, Handguard, and leather Cheekpiece. Everything you need, to make the sniper rifle you’ve always wanted. We also include an
original M84 data plate for the scope. Bound to satisfy you on the range and increase
the value of your rifle too! These parts are normally quite expensive on their own!
Barrels are short chambered as per military specs, so make sure a Gunsmith checks
the final assembly. Very limited quantity in stock now.................. $649.95 GRD335
Complete kit at an unbelievable
price!
DELUXE M14/M1A
SNIPER SCOPE MOUNT
This M14/M1A Tactical Scope Mount with 3 Point
locking, mounts easily to the charger guide Dovetail
and Receiver mount lug. It also has open sight channel
that lets you use your iron sights. The top feature of
this mount is that it has a rigid 3 point mounting for
both rigidity of the scope system plus maintenance
of Zero. Special Value $24.95, 3 for $69.95 M14012
Rings ...................................................$4.95 SCP007
Set of rings & mount $27.95, 3 for $79.95 M14010
M14 ORIG G.I. FLASH HIDERS
Found a few only!...$89.95 M14157
AVAILABLE AGAIN M14
FULL AUTO PARTS KITS
M14
M14
M14
M14
M14
Selector, Pin & Spring
Selector Shaft
Sear Release
Connector Rod Full Auto
Selector Lock...............$39.95 M14014
WORLD WAR I & WORLD
WAR II PATTERN U.S.
LEATHER RIFLE SLINGS
These beautiful recreations of the old style
leather slings are made to the standard
U.S. M1907pattern, as used on all the U.S.
military rifles since the turn of the century.
These are the proper slings for use on all of
the following arms:
M1903 Springfields
M1 Garand
M16
M1917 “Enfields”
Military “Trench” Shotguns
M14
Made from good quality leather with brass
or steel hardware, and marked with proper
style WWI or WWII markings and dates;
these slings will enhance that special old rifle
in your collection. Specify when ordering:
1. WWI Model 1907 Sling (w/brass hardware
and WWI date)............................. SLNG024
2. WWII Model 1907 Sling (w/steel hardware
and WWII date) SLNG025
.................... $16.95 ea., 3 for $47.95
M1 TANKER GARAND .30-06 BARREL - HAVEN’T BEEN AVAILABLE FOR YEARS!
Brand new and made by one of America's premier barrel manufacturers. Parkerized and
ready to install. Length 18.25 inches. .30-06........................................$149.95 GRD004
.308......................................................................................................$149.95 GRD336
Specify when ordering
M1 GARAND ACCESSORY PACK
Terrific set of accessories for the Shooter
or Reenactor! Made up of both original and
reproduction items, the Pack
NEW!
includes the following items:
EM
IT
GARAND GUN CASE
GARAND CARTRIDGE BELT
MILITARY MANUAL
M10 CLEANING SET w/brush
CHAMBER BRUSH
SNIPER CHEEK PAD
1 QUART OF LSA - MILITARY GUN
LUBRICANT
CLEANING ROD STOP
USGI DUMMY .30 RD
3 EN-BLOC STRIPPER CLIPS
M15 G.L. SGT.CASE
PULL THRU ROD &
CORD
M1 GARAND KITS
Almost sold out! All parts but barrel
& receiver, and op rod catch & clip
latch. Good condition & serviceable.
Some parts are new. G.I. walnut
handguards included. G.I. walnut
stock. Gathered a few more
..............................$580.00 GRD331
Also have a selected kit – metal parts
are personally selected – wood is same
as above............... $610.00 GRD332
ALSO: Your choice of
1907 Leather Sling or
Canvas WW2 style sling.
Specify when ordering.
A Retail Value of over
$145.00 For Just…
$79.95 GRD329
***A great gift for a
Garand owner!***
REMINGTON 40X SERIES RIFLE STOCKS
NEW WALNUT FRONT AND REAR
HANDGUARD SET
With metal $32.95 GRD051
Without metal $24.95 GRD210
NEW ITEM!! M1D BARREL BLOCK
(the base for the barrel) fully
machined from solid billet –
100% like the original and to
the G.I print
$89.95 GRD316
Investment cast M1D barrel block
$59.95 GRD113
M1 GARAND CLIPS
Current Production
By U.S. Government Contractor - GRD275
5 for................................................ $9.95
10 for............................................ $14.95
20 for............................................ $24.95
40 for............................................ $39.95
Nice fresh spring tension in your clip
SPECIAL GARAND CLIPS
1.2 round clip for match shooters
.................................................$8.00 ea,
5 for................................. $24.95 GRD131
2.5 round hunting clips
.............$8.00 ea, 5 for $24.95 GRD130
COMBO. New Style M3A1
TOOLS WITH
CHAMBER BRUSH
The Latest and best.
A. Used G.I.................... $19.95 GRD134
B. Like new tool w/new brush
................................. $24.95 GRD138
C. Absolutely New G.I. WWII original tool
in orig G.I. grease & package (no brush)
.................................. $29.95 GRD165
USM82 SNIPER SCOPES FOR
THE M1C & M1D & 1903A4
SPRINGFIELD, WWII &
KOREAN WAR SNIPER RIFLES
Beautiful exact repro with original markings for the Griffin & Howe M1C mount
or the M1D scope mount. See info below
............... $399.00 $499.00 SCP040
7/8" diameter tube, crystal clear optics,
tapered post reticle, polished blued finish, sliding sun-shade and a rubber eye
cup. All of the major components are
stamped with military part numbers and
the tube is stamped with period serial
numbers and stock numbers. Each scope
comes factory set to zero/300 yards.
Note: We have been able to reduce the
price of our M82 scope by $100.00
M1 GARAND BLANK ADAPTER
GRD126 U.S. G.I. pattern, new..... $9.95
3 for.........................................$24.95
GRD161 NATO pattern................. $8.95
5 for.........................................$29.95
LATE T-37 M1 GARAND SNIPER
FLASH HIDER
$34.50 GRD111
MI GARAND CLEANING KIT
Kit contains M10 cleaning rod, bore
brush and a G.I. carrying pouch. CLN064
$17.49 3 for $49.50
Handle for M10 cleaning
Rod for Garand Rifle –
hard to find $7.95,
3 for $22.50 CLN047
Orig G.I. M10 handles
..........$9.95 GRD281
GARAND BROKEN SHELL EXTRACTORS
Dual use for .308 (7.62x51) and .30-06
......................................... $5.95 BSE013
Beautiful original rifle stocks from the Remingto factory. Cholly
Brand new!
purchased these about 20 years ago from Remington Arms and
Never on a gun!
buried them in the ‘Grotto’. Now resurrected from their deep
sleep, they are begging to be connected to actions! These are grade A walnut stocks. Exceptionally nice and very
limited!......................................................................................................................................$125.00 STK379
D2
M1 GARAND
PARTS
SARCO,
INC.
& ACCESSORIES
50 Hilton Street, Easton PA 18042
www.e-sarcoinc.com
www.sarcoinc.com
610.250.3960 Fax: 610.250.3961
E-mail: sarcopa@sarcoinc.com
NEW!
ITEM
WWII U.S. PATTERN CLEANING ROD CASES
WITH WWII STYLE BELT HOOKS
LATE PLASTIC WWII OILER—G.I.
NEW $13.95 Few Only OIL035
These are nice as they have leather straps
ing – new – show some storage
For M1 Carbine rod................... $12.50
For M1 Garand rod.................... $12.50
Special – 1 of each..................... $21.95
ORIGINAL G.I. M1 GARAND BOLTS
Stripped........................ $69.95 GRD070
Complete....................... $89.95 GRD071
New and like new............................................. $59.95
3 for................................................. $149.95 GRD028
Front and rear handguard set, new......$37.50 GRD274
brand new.......................$9.95 MISC062
G.I. Sight pouch only.......$3.95 MISC262
G.I. Mounting jig for installing base to
gun – rare, original....... $40.00 MISC263
See our K Page for more
Garand parts
COLLECTOR GARAND PARTS:
7.62 NATO (.308) M1 GARAND KIT
All parts but receiver and op rod catch &
clip latch – for 7.62 NATO – Stock is exc to
new, barrel is rechambered in 7.62 NATO by
shortening a G.I. barrel, G.I. handguards are
new walnut, system is 1/2" shorter due to
NATO Round. Note: These are chambered for
7.62 NATO +.308. The NATO is a slightly deeper
chamber. Small lot $580.00 GRD333 Hand
select $610.00 GRD334
LAST OF THE NEW ORIGINAL G.I. M1 GARAND
BUTTPLATES
These have
been sleeping in
our warehouse for 20 or 30 years.
Absolutely brand new unissued.
These are from a U.S. Government
contractor buy out years ago. This
is probably your last chance to get
a new original G.I. buttplate. When
these are gone, that’s it! Limited
numbers available
.......................... $39.95 GRD326
1.
2.
3.
4.
M1C/M1D SNIPER PARTS
M1D rear handguard New G.I. original
GRD033................................................. $25.00
T37 flash hider GRD111......................... $29.95
M1D barrel block GRD113...................... $59.95
M1D scope mount GRD112.................... $47.50
CLN117
CLN118
CLN119
PARTS FOR .308 (7.62x51) CAL M1
GARAND ORIGINAL .308 STOCK
M1 GARAND & M1 CARBINE GRENADE
LAUNCHER SIGHT with pouch. Orig G.I.,
Winchester, HRA hammer GRD231
............................................................$40.00
HRA gas cylinder lock screw GRD236
............................................................$30.00
HRA windage knob GRD237......................$35.00
HRA safety GRD238..................................$40.00
Win. Trigger housing reparked Stripped GRD152
............................................................$65.00
Milled stock ferrule w/swivel GRD174
............................................................$40.00
Bullet guide, post war stamped GRD248
............................................................$10.00
Bullet guide, post war stamped with thumb
notch GRD249......................................$15.00
& edg-
Orig. Brass oil & throng set, exc. condition.
OIL015 ............................................$35.00
Orig plastic oil & throng set, used exc.
condition OIL016 ............................... $8.50
•
•
•
•
•
•
•
•
•
GARAND ACCESSORY KIT
Perfect new leather sling
Orig. late oiler
Orig. combat cleaning throw
NEW!
Cleaning brush
ITEM
Front & rear sight cover
10 – 8 shot clips
Orig. WWII accessory pouch
Cleaning rod buffer
G.I. type carrying case
$70.00 value $49.95 GRD172
GARAND SNIPER LEATHER CHEEKPAD
Special new low price. GRD124
Exact repro with proper markings
$18.95 3 for $49.95
Go to our websites for a complete selection of Garand bolts by maker and dash
variation. We have sorted out 13 variations – we even offer heat treat lots for
serious collectors.
COMPLETE SET OF M1
GARAND STOCK HARDWARE
ORIGINAL G.I. WWII M1 GARAND
SLOTTED COMBINATION TOOLS
In the original G.I. wrapper. Been
buried for 10 years. While the few
last - $39.95 TOOL016
A perfect reproduction of the grenade
launching rubber boot (slip on) for the
Springfield and M1 Garand. Absolutely
meticulously beautiful!!
............................... $34.50 MISC088
M1 GARAND GAS CYLINDERS
U.S. G.I. Gas Cylinders, not
foreign made replacement
parts.
2A.Serviceable grade, gaged for functionality.
Sarco’s Price ONLY GRD096
......................................... $85.00 each
2B. Refinished, serviceable. $99.95 GRD097
SPECIAL THIS MONTH!
Free original G.I. M84 scope data plate
with each M84 scope purchase!
M84 TELESCOPE SIGHTS FOR
THE1903A4 SPRINGFIELD &
M1D GARAND SNIPER RIFLES
A Mil-Spec reproduction of the original – produced by a company that produced these scopes
for a military contract years ago. Used original
drawings for the production. Comes with rubber
eye shield & date plate. Factory c
............................................. $399.00 GRD260
Add on deals:
A. M84 scope with M1D scope mount
............................................. $434.95 GRD261
B. M84 scope with M1D scope mount & scope
mount barrel block................ $479.95 GRD262
C. M84 scope with M1D scope mount, barrel
block, orig. G.I. new M1D rear handguard, sniper
cheek pad & T-37 prong sniper flash hider
............................................. $549.95 GRD263
M84 repro scope buyers from other sources-we
have original G.I. unnumbered M84 sccope data
plates from Libbey Owen Ford (the manufacturer)
NOS..........................................$24.95 M84014
Rubber eyeshield for M84 scope. Current production...........................................$14.95 M84055
All cleaned up and reparkerized. Buttplate
w/screws, rear swivel, stock ferrule &
swivel assy $39.95 GRD136
Hardware Set same as above but Not
reparkerized… $33.50 GRD213
RARE M1A2 GRENADE ADAPTER
FOR U.S. SERIES OF GRENADE
LAUNCHER (ALSO MANY
EUROPEAN)
ORIG WWII G.I. M1 GARAND KHAKI
CLEANING ROD POUCH
MISC124
New cond. Few only WWII markings.
Found in warehouse $14.95 GRD299
SPECIAL M1D SNIPER COMBO SET
New G.I. Handguard
T-37 Flash hider
Cheek Pad
Barrel Block
Scope Mount
Value $200.00. GRD145 SPECIAL $149.50
M1D SCOPE MOUNT
Price reduced! Only $47.50
Scope mounts for the M1D Garand
Sniper rifle. These are for the 7/8" diameter
M81 - M82 - M84 Scope. New condition.
GRD112
New condition.........$29.95, 3
for $79.95 Grenade not included.
RARE M11A3 WWII RIFLE
GRENADES
The stocks are new walnut G.I. stocks that were .308 cal & we converted them to .3006. Fit is perfect for .30-06. There is a tiny hairline from the conversion that is visible.
Handguards are new production walnut.
Complete stock set (wood only)............................ $59.95, 3 for $169.95 GRD278
Quantity purchases, please call Cholly. Will trade on quantities
GARAND PARTS
GRD330
rust
GRD002
GRD001
GRD071
GRD070
Barrel G.I. Orig WWII Dated, poor bore & some
$49.95
Barrel “Clunker Grade”..........................$20.00
Barrel (Used, Fair)..................................$34.95
Bolt (Complete)......................................$89.95
Bolt (Stripped Used)...............................$69.95
See our website for a complete
offering of Collector Garand bolts
BRUSH-001 Bronze bore brush 30 cal................. 10/$9.95
GRD065 Bullet Guide............................................ $7.50
GRD046 Butt Swivel.............................................. $7.50
GRD042 Buttplate Good to VG, G.I. (Used)...........$22.50
GRD043 Buttplate Screw Bottom (Long)................. $2.25
GRD044 Buttplate Screw Upper (Small)................. $1.50
GRD318 Buttplate w/trap assy G.I. exc to like new.$30.00
GRD319 Buttplate w/trap assy G.I. fair to poor....$15.00
GRD320 Buttplate w/trap assy G.I. new..............$29.95
GRD115 Carrying Case........................................$14.95
GRD021 Clip Ejector.............................................. $4.95
GRD081 Clip Latch..............................................$24.50
GRD082 Clip Latch Pin.......................................... $2.00
GRD083 Clip Latch Spring..................................... $1.35
GRD214 Danish contract Garand oiler
............................................. $3.70, 3 for $8.95
GRD259 Early Rear sight windage knob spring...... $3.00
GRD076 Ejector..................................................... $3.25
GRD077 Ejector Spring.......................................... $1.50
GRD078 Ejector w/ Spring..................................... $4.95
GRD086 Elevation Pinion (Late Style)...................$26.50
GRD075 Extractor-current production.................$15.95
GRD310 Extractor G.I. new................................ $20.00
GRD079 Extractor Spring w/ Plunger.................... $3.45
GRD074 Firing Pin...............................................$15.00
GRD186 Flash hider lock bracket G.I. M2............$25.00
GRD111 Flashider T-37 (Pronged)........................$34.50
GRD062 Follower Arm.........................................$15.00
GRD064 Follower Arm Pin..................................... $2.45
GRD068 follower assy..........................................$19.95
GRD061 Follower Rod............................................ $7.00
GRD066 Follower Slide........................................$12.00
GRD294 Front handguard with metal G.I. good cond.
..............................................................$24.95
GRD295 Front handguard w/metal G.I. VG cond.$29.95
GRD109 Front Sight............................................$12.00
GRD110 Front Sight Screw.................................... $1.25
GRD096 Gas Cylinder (Serviceable)......................$85.00
GRD097 Gas Cylinder (Refinished/Serviceable)....$99.95
GRD100 Gas Cylinder Lock (Used).......................$20.00
GRD104 Gas Cylinder Lock Screw Late (Used).....$20.00
$14.95, 3 for
$39.95 GRD143
Neat paper weight!
ORIGINAL WWII GARAND & M1CARBINE
G.I. canvas muzzle cover with strap $8.95
MISC047
M1923 (WWII Style) U.S. CARTRIDGE BELTS for M1 Garand
The standard 10-pocket with
cartridge belt as used during
W.W.II to carry .30-06 ammo
for the M1 Garand and M1903 Springfield Rifles.
Each belt has 10 individual pockets which can
hold 2-5 round stripper clips or 1 - M1 Garand
8 rd. clip of ammo. The pocket flaps are secured
with typical lift-the-dot fasteners. Belts are
adjustable for waist size, and each belt has many
metal grommets for attaching G.I. bayonet scabbards or other items of field gear. Nicely marked
“US” on the front pocket. Belts are made from
heavy webbing, dyed the proper greenish/khaki
color. Our belts are in new condition. SPECIAL
SALE!!! $19.95 ea. 3 for $54.95 GRD125
NEW!
ITEM
M1 STAINLESS STEEL GARAND
OP ROD SPRINGS
The Best On The Market!
Just got a new fresh shipment made from G.I.
blueprints. Replace your tired spring or put
away a spare now! Stainless Steel 17-7
....................... $7.45, 3 for $19.95 GRD171
Standard Music Wire Spring................ $5.95,
3 for...................................... $14.95 GRD296
ORIGINAL NEW G.I. GARAND OP ROD SPRING
Found some more in warehouse. $7.50
3/$19.95 GRD059
Your choice of .520
or .595 NM aperture.
$39.95 GRD089
Also for M14
M1 GARAND OP. RODS
M1 GARAND OPERATING ROD TIPS (pistons)
BB013 - 9mm 1-10 twist 17" .980 od 4140 no
chamber.................................................$29.95
BB014 - 22 cal 1-9 twist 24 ½ .980 od 4140 no
chamber.................................................$34.95
BB015 - 30 cal 1-10 twist 18 ½ 1.312 od 416SS
no chamber............................................$29.95
GRD102
GRD286
GRD016
GRD080
GRD015
GRD013
GRD012
GRD014
GRD041
GRD039
GRD034
GRD032
GRD033
GRD040
GRD089
GRD037
GRD038
OIL002
CLN116 GRD182
OIL035 OIL015 OIL016 Gas Cylinder Lock w/Hump (Used)........$23.00
Gage......................................................$45.00
Hammer................................................$24.95
Hammer Int’l Harvester..........................$40.00
Hammer Pin............................................. $2.00
Hammer Spring....................................... $2.00
Hammer Spring Housing........................$10.95
Hammer Spring Plunger........................... $4.00
Handguard Band Rear ............................ $5.00
Handguard Ferrule Front ....................... $6.00
Handguard w/metal front G.I. special select
..............................................................$34.95
Handguard Rear M1D Used...................$20.00
Handguard Rear New G.I. M1D..............$29.95
Handguard Spacer Front ........................ $5.00
Hooded Rear Sight Aperture National Match
..............................................................$39.95
Lower Band...........................................$15.00
Lower Band Pin........................................ $1.00
Lubriplate pot, G.I. 3 for.......................... $3.95
M10 cleaning rod handle... $7.45, 3 for $20.00
New G.I. stripped Early WWII rear sight pinion
..............................................................$55.00
Oiler, late plastic WWII, new...................$13.95
Oiler, brass & throng set, exc.................$35.00
Oiler, plastic & throng set, used, exc
................................................................ $8.50
WWII military style canvas carrying case
for the M1 rifle. These “U.S.” marked cases
are made of heavy, olive drab canvas and
equipped with a zipper, leather tabs and a
shoulder carrying strap. GRD115
..................... $14.95 ea., 3 for $42.95
NATIONAL MATCH REAR SIGHT
APERTURE
12 GAUGE BLANK BARRELS
JUST IN! BARREL BLANKS
FOR PROJECTS
WORLD WAR II PATTERN
M1 GARAND CARRYING CASE
M1 GARAND BUTTSTOCKS
NM SIGHT & APERTURE BUYERS PLEASE
NOTE: The aperture is made slightly oversized to
be fit to your sight base. The procedure is simple
& instructions are included. See our website for
the instructions if you wish.
Terrific barrels for replacing shot out or troubled
shotgun barrels or that special project gun you
are working on.
BB009 - 12 gauge un chambered smooth bore 27
½ 1.062 OD 4140 steel..........................$24.95
BB010 - 12 gauge un chambered smooth bore 29
½ 1.312 OD 416ss..................................$29.95
BB011 - 12 gauge un chambered rifled bore 25½
1.312 od 4140 steel................................$44.95
BB012 - 12 gauge un chambered rifled bore 27 ½
WWII PATTERN WEB SLING
Just reproduced for U.S. complete w/
markings. OD with all proper metal
fittings – Beautiful. Also proper for
Springfield & Enfield $9.95, 3 for
$28.45 SLNG057
These are original U.S./G.I. walnut stocks, some in especially choice condition. Several
grades available (these are the wood butt stocks only, no handguards or metal included).
Good to very good condition, has seen some use, but no abuse. Original finish, no cracks,
nice walnut, much better than average stocks GRD024......................................$110.00
M1C/M1D Sniper Stocks, We found a small lot of sniper stocks mixed in with the excellent condition reworked stocks described above. These sniper stocks have two small screw
holes in the bottom of the stock where the sniper cheek pad would have been attached.
GRD026 – These stocks are not marked
The cheek pads are not on these stocks, just the holes are present....... GRD026$145.00
Same stock with open box/SA inspectors mark ZZ2 ........................................$225.00
G.I. butt stock, average used condition, no cracks, might have minor chips on edges
GRD027............................................................................................................... $75.00
M1C/M1D stock as above with arsenal repair, no markings................................ $89.50
EMCF stock............................................................................................. $350.00 & up
GAW stock............................................................................................... $350.00 & up
HRA stock............................................................................................... $225.00 & up
Original .308 (7.62 NATO) Garand stock, new G.I................................................ $59.95
Lost in warehouse for 10 years. Repainted and may have minor storage
dings on fins. These don’t exist anymore
Small quantity only - $34.95 AM125
1.312 od 416ss.......................................$49.95
BRAND NEW GARAND STOCK & HANDGUARD SETS IN WALNUT
FRONT HALF G.I. M1
GARAND RECEIVER
Brand new, made to Government specs. Replace
your worn piston - diameter .5265”
(high end + .0005") Made of the proper
174PH steel $9.95,
3 for $22.95 GRD211
NATIONAL MATCH REAR
SIGHT BASES FOR M1
GARAND & M14 (M1A)
New condition $46.50 GRD085
.30 CAL BORE BRUSHES
Normal .30 cal bronze
brushes
10/$9.95,
50/$39.95, 100/$69.95 BRUSH-001
Stainless steel bore brush fur cleaning those
tough military bores 5 for $8.95 CLN120
GRD056 Op Rod (National Match)..................... $175.00
Note: Above op rods are gaged & checked
GRD060 Op Rod Spring (Used)............................... $5.00
GRD052 Operating rod G.I...............................$120.00
GRD141 Original unmodified Dash 9 operating rod
gauged piston – rod reparked
..........................................................$175.00
Original # 6 round edge op rod – cut... $165.00
GRD088 Rear Sight Aperture...............................$11.50
GRD094 Rear Sight Assembly Late .....................$60.00
GRD084 Rear Sight Base.....................................$25.00
GRD085 Rear Sight Base National Match
............................................................ $46.50
GRD093 Rear Sight Cover...................................... $5.00
GRD017 Safety....................................................$19.95
GRD112 Scope Mount M1D ................................$47.50
GRD011 Sear......................................................... $6.00
GRD114 Front & Rear Sight protective cover with muzzle
can.......................................................... $5.00
SLNG024 Sling Repro WWI Leather, brass hook
............................................................ $16.95
SLNG025 Sling Repro WWII Leather, steel hook... $16.95
GRD107 Stacking Swivel (Used)............................. $8.00
GRD108 Stacking Swivel Screw, new...$2.95, 5/$11.95
GRD028 Garand stock for .308 NATO cal gun, new
................................................................$59.95
Original USGI op rods made in the U.S.A. for
use on the Italian Garand. We have had a precision made Stainless Steel 174 P.H. tip made to
replace the shorter Italian tip. These rods are
proper length for the M1 Garand Rifle and are
freshly parkerized and function fit for guaranteed
performance. The original M1 Garand op rods
are getting EXTREMELY DIFFICULT TO FIND, so
please consider this now in order to hedge against
the scarcity of this item in the very near future.
$140.00 GRD052
M1 GARAND BRAND NEW BUTTPLATE
ASSEMBLY $29.95 GRD220
SPARE PIN & SPRING KIT
FOR M1 GARAND
Clip latch spring
Extractor spring
& plunger
Hammer spring
Op rod spring
Clip latch pin
Hammer pin
Trigger pin
Lower band pin
Op rod catch
pin
Value over $25 - $12.95 GRD219
M10 cleaning rod handle
$7.45, 3 for $20.00 CLN116
GRD027
GRD048
GRD047
GRD049
GRD050
GRD026
GRD024
GRD323
GRD009
GRD019
GRD020
GRD023
GRD022
GRD152
GRD008
GRD092
GRD090
GRD212
Stock Average Used Condition Average No
Cracks................................................. $75.00
Stock Ferrule Assembly..........................$13.50
Stock Ferrule Stripped...........................$10.00
Stock Ferrule Swivel................................. $7.50
Stock Ferrule Swivel Screw...................... $2.95
Stock U.S./ G.I. Sniper MID/MIC (Used)
$145.00
Stock U.S./ G.I. Used (Good Condition)
$110.00
Trigger forging, orig G.I. new................... $4.95
Trigger & Sear Assembly...................... $12.00
Trigger Guard Milled............................ $25.00
Trigger Guard Stamped........................ $16.50
Trigger Housing Assembly
............................................................ $99.00
Trigger Housing Stripped..................... $40.00
Trigger Housing, Win. Reparked Stripped
$65.00
Trigger Pin..............................................$1.50
Windage Knob early original
............................................................ $55.00
Windage Knob (Late Style)
............................................................ $11.00
G.I. winter trigger in orig. pkg
............................................................ $19.95
SARCO, INC.
Whoaaaa…. Cholly’s Done it Again!!!
1911 Series 80 single stack, single action, full size pistol frames available in
either ordnance grade steel or lightweight aluminum! These are finished frames
except for several features that are unfinished to comply with BATF directives
classifying these as Non-Firearms in their present condition. Slide rails, hammer & sear pin holes, mainspring housing retaining pin, and ejector leg holes
remain to be applied. Grip screw holes are drilled and tapped. The frames can
be easily modified to Series 70 with the use of a commonly available adapter
shim. The Steel frame accepts the ‘Clark©’ type 1911 barrel while the Aluminum
frame accepts standard 1911 barrels. A BATF letter of ‘non-firearm’ status,
accompanies each order. These are the best quality 80% frames on the market,
manufactured by a major 1911 manufacturer! Act now before this small lot is
gone! Fits 4.25" slide or smaller.
ALUMINUM 80% FRAME......................................................................................................................................................... $125.00 C45328
STEEL 80% FRAME................................................................................................................................................................. $125.00 C45329
ALSO THESE 80% FRAMES JUST IN !!!!!
#500267 Officers length grip frame, steel with checkered front strap. Series 80, Single action, Single stack. Fits 4.25" slide or smaller.
............................................................................................................................................................................................... $125.00 C45330
#500649 Extra Small Para Frame for 3" slide. Series 80, aluminum, Double stack, Single action............................................. $125.00 C45331
#500675 Para LDA Officers length grip frame in steel with checkered front grip strap. Accepts 4.25" or smaller slide. Single stack and Double
action...................................................................................................................................................................................... $125.00 C45332
#500678 ‘Agent’ extra small steel frame with checkered front strap. Single stack, Double action, and fits 3" slide................... $125.00 C45333
E-mail: sarcopa@sarcoinc.com
NEW G.I. CLONE ROCK ISLAND ARMORY .45 1911
& 1911A1 BARRELS
The rifling is absolutely beautiful and the bore surface is
very smooth. Made from ordnance steel.... $49.95,
3 for............................................$143.50 C45202
www.sarcoinc.com
610.250.3960
THREADED 1911 BARRELS
5-1/2 Inch
Brand new black oxide finished barrels in 3 calibers.
Thread is standard .578x28 TPI.
9mm Model 1911 5-1/2” barrel.........$60.00 C45360
.38 Super Model 1911 5-1/2” barrel
........................................................$60.00 C45361
.400 Corbon Model 1911 5-1/2” barrel
........................................................$60.00 C45362
THREADED CAP FOR THREADED BARRELS
Steel black oxide finished threaded cap fits
Barrels with .578x28 threads per inch.....$13.00 C45363
PARA LDA SLIDES Brand new precision engineered
PARA light double action slides with Trijicon front and rear sights installed
are now available at Sarco. We offer one for the 3 inch 9mm ‘PARA LDS CARRY 9’, and one for the 3.5” 9mm ‘PARA LDS OFFICER 9’ pistols. Beautifully finished in a dark gray Physical Vapor Deposition (PVD) finish. Wide rear serrations on the slide ensure an easy grip and
the pronounced Trijicon sights ensure the fastest eye ‘line up’ to target. The value of this package is astounding as the market price on the
sights is almost the same as the cost of the stripped slide! In this package, it’s like you are getting the slide for free!
1. 9mm Para LDA Officer 9 Slide w/sights....................................................................................................................................................$159.95 PARA154
2. 9mm Para LDA Carry 9 Slide w/sights......................................................................................................................................................$159.95 PARA159
*Specify the 3 inch or the 3.5 inch slide when ordering.
1911 PATTERN SLIDE BONANZA!
1911 PATTERN SLIDES FROM PARA ORDNANCE (SEE COMPLETE DETAILS ON LINE AT SARCOINC.COM
Sarco’s got em! Over 125 varieties! These include Standard models, Discontinued models, Overruns
and Custom Variations. Perfect time to upgrade your Para pistol or build up that 1911 frame! These
slides will also allow you to change pistol length, or caliber, or even upgrade your sights! Sarco’s
BIG VOLUME purchase, means BIG SAVINGS for you! These slides are premium material ... not
rejects or returns; material is the remaining inventory from the Corporate change over from Para
Ordnance to Para USA.
GUIDANCE FOR YOUR PARA SLIDE PURCHASE
All our Para slides are cut for the series 80 type firing pin interlock. Complete slides are built
with series 80 parts and a ramped barrel that will fit in 1911 frames that are modified for ramped
match barrels. You can build these up to work in standard U.S. G.I. 1911 type (series 70) pistols
if you wish, However doing so disables the safety features of the series 80.
Striped single action slides will work on any standard series 70 or 80, 1911 frame (series 70 is the
standard 1911) when built with the appropriate parts.
The Para LDA is a double action slide that will work only on Para LDA frames. You can however
cut the disconnector scallop in and use the slide on any standard series 70 or 80 1911 frame.
The 6" and 5" slide use standard 1911 recoil spring plugs and barrel bushing. The 4.25" slides
use Commander type recoil parts. The 3" and 3.5" slides use a unique recoil mechanism that is
available commercially.
There are 2 variations of extractors used on these Para slides. The first is the standard type which
uses any standard .45 extractor. The second is a PXT type. On this style the forward part of the extractor support rib is slightly larger in diameter. We have read that people have used G.I. extractors
as they are the same diameter in the back. PXT extractors or adapter bushings are available from
other sources. We will also soon have these available.
COMMEMORATIVE PARA SLIDES
5 inch
PARA095
4-1/4
inch
3-1/2
inch
PARA041
PARA030
3 inch
PARA001
BACKUP PISTOL OR EASY CONCEALED
CARRY?
Want a 3", 3.5" or 4" Hi-Cap
‘Snubby’? This may be the only 3”
slide on the market!!! We offer a
completely finished
new slide and one
of our wide body
frame castings
in steel or aluminum
for as little as $140.!
‘Way Less’ than the regular
price on the slide alone!
CHECK OUR WEBSITE FOR SPECIAL PARA SLIDES USED TO COMMEMORATE UNITS OR
MILITARY ACTION. LIMITED QUANTITY OF THESE EXCITING SLIDES IN STOCK!
PRICING DISCOUNTS - buy 10 slides (any assortment), take 5% off, or 25 slides (any assortment),
10% off, or 50 slides (any assortment), 15% off. WANT MORE ? Call or email Dave at mgdave@sarcoinc.com or Cholly at csteen@sarcoinc.com
(610) 250-3960 SPECIAL COMBO DEAL!
Pick anyone of our PARA Slides and pair it with one of our Frame castings .... TAKE OFF $10.00!
Just got a new shipment of 500 slides and barrels in! We’ve been out for a few
months! The last 1000 went quickly so act fast before they run out again!
A NICE ASSORTMENT theOsteh8e0rs may call
% rec
eivers
OF FACTORY CASTINGS
C45284 - P12/P13 type, wide body 1911 type double action frame casting. No
parts interchange with 1911
C45286 - 1911 type, Single stack double action frame casting. No parts
interchange with 1911
C45288 -P12/P13 type double stack single action. Uses most 1911 type parts (see
other ad) Alloy light weight frame.
C45289 - P14 type double stack double action steel frame. No parts interchange
with 1911.
C45294 -P14 type, wide body 1911 type steel double action frame casting. These
also have the enhancement of a lower accessory rail in front of the trigger guard. No parts interchange with 1911.
C45296 -P13 type double stack 1911 .45 frame casting. Uses most 1911 type
parts. Alloy light weight frame. No parts interchange with 1911.
Special price for all above frame castings..................................................$29.95,
Mix or match 4 for.................................................................................. $100.00
Big Buyers call MG Dave or Cholly. We also have other wide body configurations
available. No returns on frame castings.
C45284
C45286
C45288
C45289
C45294
C45296
SERIOUS ABOUT COMBAT SHOOTING? ROTO 4M COMPENSATED BARREL
PARA ORDNANCE BARRELS…JUST IN!
These are in short supply everywhere right now!
High quality PARA Pistol barrels available in 8
varieties while supplies last.
PAR1 3.5 inch, .45 ACP, Match, Ramped,
Stainless Steel.............. $175.00 (F500443)
PAR1E 3.5 inch, .9mm, Match, Ramped, Stainless
Steel.........................$175.00 (F501301)
PAR1F 3 inch, 9mm, Match, Ramped, Stainless
Steel...........................$175.00 (391000)
PAR1A 4.25 inch,.45 ACP, Match ,Ramped,
Stainless Steel..$145.00 (F500171) P-13
PAR1B 5 inch, .45 ACP, No Ramp, Stainless Steel
........................$145.00 (F500173) P-14
PAR1C 5 inch, .45 ACP, Match, Ramped,
Stainless Steel $145.00 (F500174) P-14
PAR1D 5 inch, .40 S&W,Match, Ramped,
Stainless Steel$145.00 (F500444)
PAR152 5 inch, 9mm, Ramped, Stainless Steel
................................$145.00 (9391100)
NEW!
ITEM
.45 SLIDE CASTINGS
Colt 1911/1911A1 .45
ACP Slide Castings
We have 3 size castings.
These are in the white and require
machining to finish.
— 3" barrel sub compact C45293
— 3.5" barrel sub compact C45292
— 4" barrel compact C45291
— 5" barrel full size C45290
Your choice and mix or match the length
$14.95, 10 for $120.00, 50 for $500.00
DOD contractors have been buying up our Roto 4M barrels because they work! MODEL 1911
COMPENSATED BARRELS in 2 calibers will reduce recoil and speed your target acquisition
especially during multiple shots. Takes a minute to install our barrel that comes with Barrel
Bushing and permanently attached and ported Compensator. Also there is less weight on the
muzzle end than with conventional screw on muzzle compensators. Most
people comment on the change of performance, but also that it looks great
too! Sold elsewhere for $175-$200, Sarco’s price is $99.95 Specify caliber
when ordering: New, made in USA. .38 caliber C45024, .400 corbon C45194
E2
MODEL 1911
THREADED 5.5”
.45 CAL. BARRELS
Always fun to modify
your Model 1911 pistol
with a brand new
threaded black oxide
finished barrel. Last
3/8 of an inch is
threaded with 28
threads per inch. Great
for muzzle devices or
suppressors
$60.00 C45321
STILL LOWER PRICES ON ALL .45 AUTO KITS
.45 AUTO “BUILDERS KITS”
Put together your own .45 “Government” pistol with our Builder Kits. Several different kits available to best fit your needs. Our parts are standard
M1911A1/Pre-’70 Government type.
Price List: #1.Builders Kit - All parts in the gun less frame and slide
$139.95 or 3 for $405.00 C45095
#2.Builders Kit – All parts in the gun less
frame, slide,and barrel.$110.00
C45096
#3.Kit - All parts in the gun less frame.
Kit includes one of our new current
manufacture G.I. type slide (unmarked) C45097 $210.00 (Regular
value $300)
C45218 - Builders Kit with Commercial Slide $235.00
Compare our prices and see how much you’ll
save compared to the competition!
Note: All gun parts may require some fitting
and technical knowledge for assembly. If
you are not knowledgeable seek professional
assistance.
BEST QUALITY COMMERCIAL .45 SLIDES
o
o
o
o
o
o
Special wide angled front and rear cocking serrations – for easy grasping
Nice subdued blue finish with sand blasted inner serrations
Lowered & beveled ejection port
Unmarked slide
With desirable snag-free rear sight
Free sight set ($20 value) All this for only..................................................$139.95 C45172
Note: Due to variations we have seen in frames & parts, slight fitting
of ejectors & extractors may be necessary
OUR NEW G.I STYLE 1911 GOVT. MODEL SLIDE
Current production compete with both G.I. sights installed. ($15 value) Made with improved
beveled ejecting port.................................................................................... $124.95 C45160
Have a few series 80 slides configuration..................................................... $125.00 C45260
COMPLETE 1911 .45 SLIDE KIT
(All Parts For Slide)
A complete set of the top half of a .45 Government model. Kit includes one of our new current
manufacture slides (unmarked), barrel, firing pin, recoil spring parts, sights, extractor, link &
pin, band bushng. Over $198.00 worth of parts for only
....................................................................................................................$174.50 C45092
Complete upper commercial slide kit for.......................................................$184.95 C45200
Our commercial slide set also available with one of our compensated barrel assy. for
........................................................................................................................... $229.95 C45093
OUTSTANDING ASSORTMENT OF QUALITY 1911 BARRELS
ROTO 4M HAMMER FORGED .45 ACP, 9MM & .38 SUPER
Built to precise tolerance by a special hammer forging process, these barrels are the
best you can buy!
The hammer forging forms the barrel around a precision mandrel and holds the tolerance to .0001”. This is much better than the typical
broached barrels found elsewhere
Note: 5” & 6” .45 barrels are L.H. twist – all
others are R.H. twisted
COMPARE THE ROTO-4M BARREL FOR ROUNDNESS
AGAINST A STANDARD BROACHED BARREL FROM A
WELL KNOWN MANUFACTURER. ALL ROTO-4M
BARRELS ARE MADE IN THE USA.
Brand new extra length barrels for all Colt/1911/Government
Model type automatic pistols. These barrels are made by the Special
Roto-4M Hammer forge process which produces the most precise
and consistent barrels for the best accuracy. Minor hand fitting
may be necessary for some guns. Barrels do not include link &
pin. Link & pin available w/barrel purchase for additional $5.00 C45281 Available in:
.400 Corbon Barrels
41/4" Commander
$51.70 C45105
6"
$56.70 C45104
STD 5"
$51.70 C45025
.45 ACP
41/4" Comm.$49.70 C45010
5"......... $49.70 C45011
6"......... $57.70 C45013
7"......... $59.70 C45014
16"....... $77.50 C45016
.40 S&W 1911 5" barrel C45277 $51.70
.38 SUPER
5".....$49.70
6".....$56.70
7".....$60.70
41/4" Comm
....$49.70
9MM LUGER
C45017
C45009
C45018
C45164
41/4" Comm
$51.70 C45163
5"
$51.70 C45019
6"
$56.70 C45020
7"
$60.70 C45021
Note: 9mm & .38’s will not fit the .45 slide
SARCO, INC.
‘PROJECT’ REAR SIGHT FOR
3 HOLE LIGHTENED COLT 1911
PISTOLS Similar to 1911 standard
VISIT MORE LONG TRIGGERS SPECIAL RUN
rear sights, this dovetailed rear
1911 GOODIES trigger pad is
sight has a width of 1.608", stands
serrated for good
.328" high with a 1.20 peep notch
IN LEFT
50 Hilton Street, Easton PA 18042
contact $12.95,
that descends .074" into the body.
COLUMN
OF
www.e-sarcoinc.com /
3 for $36.50
Width of the dovetail is .341"$3.95 ea,
OUR H-PAGE C45173
or 10 for $30.00, or 50 for. $125.00 C45359
www.sarcoinc.com
610.250.3960 Fax: 610.250.3961
BROWN LEATHER WWII TYPE
4 PRONG SEAR SPRINGS
NEW, ARMSCOR…
.45 HOLSTER
.45 Recoil Springs for the 1911 pistol
F2
E-mail: sarcopa@sarcoinc.com
Brand new reproduction of the
standard Model 1916 holster issued
with the M1911 .45 Colt pistols. This
pattern holster in the natural brown
leather color was used throughout World War I and
World War II. Our repro. holster is made from a
quality grade of leather; and just like the originals
it has the metal belt hook, leg thong, and the flap
is marked “US”. Original samples of this model
are now scarce collector’s items, too fragile and
expensive to actually use. Our reproduction holster
is economically priced and perfect for carrying your
1911 in the field or for re-enactments. $17.50
ea. 3 for $47.50 C45112
WIDE SPUR HAMMER
Desirable M1911 type checkered wide
spur hammers for the Colt .45 auto
pistol. These are new, ready to install
and upgrade your pistol. Heavily
checkered (not grooved) wide spur
provides a sure grip when thumb cocking or decocking. $12.50 C45054 (Comparable
price $23.00) Note: These are due in a month.
Send order and get on the list
GO TO OUR WEBSITE FOR A NICE ASSORTMENT OF ORIGINAL NEW COLT
PISTOL BARRELS BOUGHT FROM
COLT 35 YEARS AGO ALSO INCLUDING SINGLE ACTION ARMY BARRELS
.45 ACCURACY KIT
Upgrade your .45 Auto pistol and improve your
score with our Accuracy Kit. medium steel. Adj.
Trigger for smooth crisp trigger pull, a No. 13
match barrel link to tighten up the barrel in the
slide at the moment of firing, a high speed recoil
spring and a high speed firing pin spring.
SPECIAL KIT PRICE $13.95 C45089
.45 AUTO FRAME KIT
All parts to build a 1911A1 frame
(except the frame itself). Includes trigger, hammer,
grips, sear, mainspring, safety, etc., etc., (no slide
stop). $89.95 ea. C45099
M1911 “DIAMOND” GRIPS
These brand new
walnut grips are made
in the original World War I
style with the “Diamond” pattern
checkering. Give your
45 Auto the classic look
and feel of the original
Colt 1911 design.
$13.95/pr. 3/$36.50 GRP162
FOUND IN WAREHOUSE!!
ORIGINAL WWII G.I. COLT .45 AUTO
COMPOSITION GRIPS
These were long ago taken off G.I.
1911A1’s – when the guns were demilled.
V.G. excellent condition.
$14.95 GRP131
.45 ACP 4" CONICAL BARREL
Barrel with flared
muzzle end does away
with needing a barrel
bushing ! This is the .45
“Commando” length barrel. Makes for a quick
installation.......CLOSE OUT! $29.95 C45201
1911 .45 AUTO PISTOL PARTS
C45095 Auto Builders Kit (Less
Frame & Slide)........................ $135.00
C45097 Auto Builders Kit (Less
Frame).................................... $210.00
C45096 A
uto Builders Kit (Less Frame, Slide &
Barrel)................................... $110.00
C45218 Builders Kit w/ Commercial
Slide....................................... $225.00
C45099 Frame Kit..................................$89.95
C45089 Accuracy Kit..............................$13.95
C45091 Auto Repair Parts Kit.................$22.50
C45017 Barrel, 5”, Roto, .38...................$49.70
C45019 Barrel, 5”, Roto, 9mm................$51.70
C45009 Barrel, 6”, Roto, .38...................$56.70
C45020 Barrel, 6”, Roto, 9mm................$56.70
C45021 Barrel, 7”, Roto, 9mm................$60.70
C45018 Barrel, 7”, Roto, .38...................$60.70
C45016 Barrel, 16”, Roto........................$76.50
C45011 Barrel, 5”, Roto, .45...................$48.70
C45025 Barrel, 5”, Roto, 400 Cor-Bon....$51.70
C45013 Barrel, 6”, Roto, .45...................$56.70
C45014 Barrel, 7”, Roto, .45...................$58.70
C45010 Barrel, Commander, Roto, .45....$48.70
C45015 Barrel, Roto .45 w/ Compensator
.................................................$99.95
C45024 Barrel, Roto, .38, w/ Compensator
.................................................$99.95
C45040 Barrel Bushing............................ $6.50
C45087 Barrel Bushing Wear Gauge,
................................................Sold Out
C45085 Barrel Bushing Wrench................ $2.95
C45026 Barrel Link Pin............................ $1.00
C45028 Barrel Link, #13, NM......................$8.95
C45027 Barrel Link, Std........................... $4.95
C45098 .45 Cal. Bore Brush..................... $1.25
C45251 Colt 1911 Cleaning Rod M4......... $6.95
C45045 Disconnector............................... $7.50
FOR THE 1911
Once again available. The
normal spring acts on the sear, disconnector
& grip safety. This spring acts on the trigger as well to tighten up any slop. A great
innovation. Spring exerts constant forward
pressure on the trigger for nice crisp trigger
& prevents hammer and sear notch damage and hammer follow on. $5.95, 3 for
$14.95 C45168
.45 FLAT MAINSPRING HOUSINGS
Brand new, flat (M1911 Style) steel
housings, grooves nicely for a sure
grip. Matte gray/black finish. These
are nice! $13.50 ea., 3 for $37.50 C45082
WIDE BEAUTIFUL GRIP SAFETY FOR 1911
.45 AUTO Stop the pinch in the
web of your hand (I used to get
bloody) $16.50, 3 for $49.95
C45079 (Note: These are for
short rear tang frame. You can
fit them to Std. frame)
rated at 16lbs.................$4.95 C45326
Mag Catch for wide body 1911 frames.
Comes with release and spring
................................... $16.95 C45327
MODEL 1911 AMBIDEXTROUS EXTENDED SLIDE STOP
Keeps right handed and left
handed shooters happy with
an extended slide stop accessible from both sides. Buff
blue.................................. $14.95 ea,
3 for.................. $11.98 each C45005
ANOTHER NEW ITEM!!
AMBIDEXTROUS EXTENDED
SLIDE STOP FOR COLT
1911 AUTO – Sarco Special
$12.95, 3 for $29.95
(comparable price $35.00 ea)
C45299 Matte Stainless
OUR NEW COLLECTION OF 1911 TRIGGER STEEL & LIGHT WEIGHT
C45064
C45175
C45149
C45174
C45066
C45137
C45065
Long aluminum adjustable .................................................. $11.95,
Long aluminum non-adjustable............................................ $11.95,
Long steel adjustable ........................................................... $11.95,
Long steel non-adjustable .................................................... $11.95,
Medium aluminum adjustable ............................................. $11.95,
Medium aluminum non-adjustable ...................................... $11.95,
Medium steel adjustable.....................$11.95, 3/$32.50
3/$32.50
3/$32.50
3/$32.50
3/$32.50
3/$32.50
3/$32.50
Note: All triggers have serrated face for solid finger contact. The medium length is a perfect compromise as the short and long triggers don’t
fit all hands. Shoe length is 5⁄16". Comparable price $18.00 or more.
PISTOL & RIFLE STRIPPER CLIPS
EA.
3 for
10 for
STC003 Carcano – (light rust but works fine - Last of ‘em!)
$4.95
STC005 AR15/M16 Guide $1.50$3.50 $9.95
STC008 Steyr ‘95 Rifle
$3.95 $11.00$30.00
STC009 6.5 Dutch Rifle
$4.00 $11.00$39.95
STC010 Enfield .303
$3.00
STC011 Steyr Hahn 9mm Auto
$3.00$8.00 $20.00
STC014 Mosin Nagant $2.50 $5.00
$16.95
STC016M14
7 for $9.95
STC020 Swedish Mauser N/A $4.00$10.00
STC025 1903 Springfield, Brass, Original
$4.00 $10.00$30.00
STC029 1891 & 1909 Argentine
$1.50 $3.25
$9.00
STC031 Mannlicher 7.65 pistol $6.50 $18.00 $49.95
STC013 ‘98 Mauser steel stripper clip
$2.00 N/AN/A
STC018 ’93 Mauser brass stripper clips
$3.00$8.00 $20.00
STC028 Orig. ’98 Mauser brass stripper clips, never seen before. Few only
$3.00 ea.
STC033Replacement Mauser C-96 Broomhandle 8rd
original military N/AN/A $10.00
STC006 Rare 1896 Mannlicher stripper clips
$24.95 $59.95
STC024 SKS stripper clip $1.00$2.95 $7.95
STC032 Fine workable stripper clips for Jap type 99 & 38
5/$9.95,
10/$14.95
Note: all above stripper clips are original except 91/30
UNIVERSAL 9MM STRIPPER CLIPS
½" wide ¾" long holds 10 rds
Got a pile of ‘em so cheap cheap! STC036
10 for.......................................................... $8.00
50 for........................................................$30.00
100 for.......................................................$50.00
C45068 Ejector......................................... $4.75
C45067 Ejector Pin................................... $1.00
C45030 Extractor...................................$12.00
C45044 Firing Pin..................................... $4.95
C45301 Just in the door! Series 80,
9mm & .38 Super firing
pins– Now available for 1911
pistols........................................ $5.95,
3 for............................................ 14.95
C45029 Firing Pin Spring......................... $1.75
C45043 Firing Pin Stop............................. $4.25
C45032 Front Sight A1............................. $5.00
C45079
Grip Safety, Wide Extended Black (Note:
These are for short rear tang frame. You
can fit them to Std. frame)
.................................................$16.50
C45078 Grip Safety, Long Tang
.................................................$12.00
C45151 Grip screws, Stainless Steel, 4 for
................................................... $5.95
C45073 Grip Screw Bushing..................... $1.00
GRP131 Grip Set, Plastic, GI, exc.
.................................................$14.95
GRP162 Grip Walnut, Diamond Style, new
..................................................... $13.95
C45052 Hammer Pin................................ $1.00
C45056 Hammer Strut............................. $3.50
C45055 Hammer Strut Pin....................... $1.00
C45053 Hammer, Regular Spur................ $9.95
C45054 Hammer, Wide Spur...................$12.50
C45060 Mag Catch................................... $6.95
C45061 Mag Catch Extended.................... $9.95
C45327 Mag Catch Wide Body, Armscor.$16.95
C45062 Mag Catch Lock........................... $2.00
C45063 Mag Catch Spring........................ $1.00
C45094 Magazine Pouch........................... $7.95
C45047 Main Spring................................. $2.00
C45084 Main Spring Cap.......................... $1.25
C45083 Main Spring Cap Pin.................... $1.00
TRIJICON 1911 REAR SIGHT We obtained a small lot of fresh (2011) genuine
Trijicon rear sights that are designed for the Para Ord style slide. A perfect
replacement for your Para .45 that has weak of failing glow inserts. This is
also perfect for your custom .45 build. The Para cut is similar to the Novack
cut but not the same. Bottom dove tail width of this sight is .360. One could
easily modify your G.I. or commercial slide to take this high quality night sight. The sight
will work with a variety of commonly available .121 wide & .160 high front Trijicon sights.
Special price to celebrate our good buy...............................$44.95 - 3/$119.95 PARA137
A NEW WORLD OF
1911 .45 AUTO MAGS
SARCO HAS GONE TO EXTENSIVE LENGTHS TO
DEVELOP A SUPERIOR 1911 .45 MAGAZINE
We have sold probably 150,000 of our price busters, but we decided
we need a new & better 1911 mag & we are
very pleased with our new program. We have tested our 1st production run and are ready to roll.
This is is the results of over a year of product development.
Please check the quality features of our new magazine:
• Produced on a computer controlled high speed link press. This is
provides a stable platform for progressive dies & uniformity. Body
tooling has 6 stages & follower tooling has 16 stages. This is
assures an accurate & repeatable process with less metal stress, when fewer, less radical bends are made.
• Latest technology parallel feed lip design for proper timed release of cartridge. Special for semi wad cutters, although per technical feed back semi wad cutters may require additional timing.
• Welding is done on a Yasakawa computer controlled robotic arm argon welder. Unlike some .45 mags you can’t see the seam weld on the back.
• In house quality control gages to national standard are used for checking every stage of the production.
• QC inspection involves a 2/5D video measuring machine enabling checking of every specification & keeps the record in memory.
• Springs are tested to 20,000 cycles
• Dimple designed as a mag catch overide for easier mag insertion.
• Latest rounded follower design
• Mags are processed in a hot bath of sodium hydroxide, nitrates, & nitrites at 141º centi
grade - This is converts the surface to “magnetite”
• All process done under specification of MIL-DTL-13924 & ASTM-D769 & ISO-11408
• The tube is carburized (case hardened) by nitriding (heat treated in a nitrogen
atmosphere). This retaines a tough core (ductility, flexibility, springiness & resistance
to stress fractures) while producing a 46-48 HRC surface hardiness, creating scuff
resistance, fatigue & corrosion resistance. Most important, it eliminates any chance for deformation of the front of the mag from cartridge inertia.
• For use in all Gov’t & Commerical 1911 pistols 1911, 1911A1 - Gov’t Series 70, Series
80, commander, Essex, Rock Island, etc. - Also the many, many, many aftermarket 1911’s.
SARCO SPECIAL
Two of our famous 1911 .45
mags plus a web mag pouch
(below) for only........$20.95,
2 sets for.....$39.95 C45310
Plus with all of the above a killer price - Only $8.95, 10 for
$74.95 C45298
DOUBLE MAG POUCHES
FOR COLT 1911 .45
NEW VARIATIONS OF OUR 1911 .45 ACP MAGS JUST IN THE DOOR
Exact repro with WWII markings. We
had these 2 years ago but got lost in the
warehouse.................................. $4.95,
3 for............................. $11.95 C45280
.45 ACP PROJECT BARREL
Nice 6 inch .965 OD chambered
barrel blank for your next project
$19.95 MISC276
8 ROUND .45 MAGAZINE
New, blued steel
magazine for all .45
ACP Government
Model/M1911 type
pistols. Base plate also acts as finger
rest to improve your grip on the gun.
$16.95 ea. RPM122
C45059 Main Spring Housing Retainer Pin
................................................... $1.40
C45082
Main Spring Housing, Flat (Checkered)
.................................................$13.50
C45145
Main Spring Housing Flat &
Grooved, Composite..................... $8.75
C45171
Main Spring Housing, Steel w/loop
.................................................$16.50
C45050 Main Spring Retainer................... $1.00
C45049
Main Spring, for Alum.Frame....... $1.25
C45001 Rear Sight................................... $4.75
C45326 Recoil Spring, Armscor................ $4.95
C45036 Recoil Spring, Standard............... $2.75
C45037 Recoil Spring Guide..................... $4.65
C45038 Recoil Spring Guide, Commander.$3.50
C45034 Recoil Spring Plug........................ $4.00
C45232 Recoil Spring Plug G.I. New
.................................................$14.95
C45126 Recoil Spring, High Speed............ $3.95
C45138 Reverse Recoil Spring Plug........... $7.50
C45074 Safety Plunger............................. $1.45
C45075 Safety Plunger Spring.................. $1.75
C45086 Screw Driver & Take Down Tool
................................................... $4.95
C45058 Sear............................................. $8.50
C45057 Sear Pin....................................... $1.00
C45051 Sear Spring.................................. $3.95
C45111 Sight Set, Battle Combat............$14.95
C45092 Slide Kit.................................. $168.95
C45076 Slide Stop Plunger....................... $1.45
C45003 Slide Stop, Standard..................$12.00
C45002 Spring Kit.................................... $7.75
C45046 Thumb Safety............................$10.00
C45173 Trigger Alum 3 Hole...................$12.95
C45064 Trigger Long Alum Adj...............$11.95
C45175 Trigger Long Alum Non-Adj........$11.95
C45149 Trigger Long Steel Adj................$11.95
C45174 Trigger Long Steel Non-Adj.........$11.95
C45066 Trigger Med Alum Adj................$11.95
This is is half the price of most reasonable .45 mags!
OEM or Large Quantity Buyers Contact Cholly or Dave at (610) 250-3960 (ext. 223)
Check our website for additional info & pictures of our fabulous tooling
Stainless steel magazines........................ $10.95,
3 for........................................... $29.95 RPM121
G.I. marked 1911 magazine marked
.45 ACP #1005-00-8694 MFR8R320................................................. $10.95,
3 for..................................................................................... $29.95 RPM155
WWI PATTERN .45 1911 MAGS WITH LANYARD LOOP
.............................................................................................. $12.95 each,
OR buy 3 mags for $36.95 and get a free pistol lanyard for the mags! C45295
HIGH QUALITY 10 ROUND
.45 1911 MAG
.45 single stack magazines for 1911 Colt
Special............................... $19.95 ea,
3 for............................ $49.95 RPM127
SARCO SPECIAL
WORLD WAR I PATTERN .45 1911
MAGS WITH LANYARD LOOP
ORIGINAL BROLIN 1911 MAGS
C45238 7RD for detachable bottom weight
with orange composite trough follower
............................................$24.95
RPM158 7RD Brolin marked mag......$19.95
RPM283 8RD Brolin marked with composite
floorplate.........................................$24.95
From the SWEDISH shipment new
ORIGINAL FACTORY PARTS for the
M1903/M1907 BROWNING PISTOL
New original barrel (9mm Browning)
SWP001.......................................$40.00
New original slide SWP004...........$40.00
New original magazine SWP003...$15.00
Or buy 1 of each for SWP002 ......$74.95
............................. 3 sets for $195.00
Multiple mag prices............3 for $35.95
.................................. 10 for $100.00
New original rear sight SWP005...$11.95
Use one of these barrels to convert your
(bushed) .380 cal. M1907 to original
military caliber and add $100’s to your
gun’s value.
C45295 - 1911 mag with lanyard
loop................................$13.95
Buy 3 mags for $36.95 and get
a free pistol lanyard for the mags.
These are rarely seen now a days.
Best way to participate in fast
combat shooting where you must
drop and load mags quickly.
Avoids damage to your dropped magazines.
WWI Cavalry and vehicle crews would
keep 2 or 3 mags on a lanyard for combat
purposes! Original mags came with hemp
twine so you could tie them to the lanyards
individually. These magazines are made
on the same automated machinery as our
famous magazines shown above. This is
the mag to have if you want to be serious
about CQB firing and reloading quickly.
Very popular for modern combat pistol
tournaments.
SPECIAL OFFER!
2 lanyard loop
C45137
C45065
C45148
C45077
Trigger Med Alum Non-Adj.........$11.95
Trigger Med Steel Adj.................$11.95
Trigger Med Steel Non-Adj.........$11.95
Tube Slide Stop & Safety Plunger
................................................... $4.95
mags w/lanyard and U.S.
military double
mag pouch
$29.95
C45318
SARCO, INC.
MORE 1911 PISTOL PARTS
BRONZE .45 CAL. CLEANING BRUSHES
5 for $4.85 C45098
.45 1911 SKELETON HAMMERS
E-mail:
Available again and at a special price
- Others get $50 to $75 for these.
Could require very minor fitting to
some grip safeties due to the variations in manufacture of
NEW
grip safeties.Our Price $14.95,
ITEM!
3 for $36.95 C45256
9mm.............. $3.95ea or 10/$24.95 Para150
sarcopa@sarcoinc.com
.45 ACP........$3.95ea or 10/$24.95 Para151
MODEL 1911 SCREWDRIVER & TAKE DOWN TOOL
Original WW2 era tool for the
Model 1911 pistol. Handy and
very compact in size. Issued
from WW1 on, these tools were
originally part of the 1912 Squad
Cleaning Kit. VG/Exc. condition
...................................................... $4.95 C45086
We have a few with manufacture markings like
‘Stanley’ and ‘Metlglas’. Specify mfg when ordering
$9.95 ea. C45320
.45 1911 ORIG. SEAR SPRINGS
Another find in the warehouse — while the few
last. $5.95ea., 3 for $14.95 C45319
COLT 1911 STEEL MAINSPRING
HOUSING w/LANYARD LOOP
Housing is grooved for a sure
grip 1911A style - nicely blued
$16.50, 3 for $47.50 C45171
WW2 BRITISH COMMONWEALTH
HELMET W/ AUSTRALIAN EMBLEM
Well-made steel British style helmet
with 1st pattern spring loaded canvas
chinstrap. The famed Australian 6th
Division emblem is adorned on the left
side..........................$32.95 HLM027
Can also cut to length for 5" 9mm guns
BACK AGAIN AFTER BEING OUT OF
STOCK. 1911 COLT HIGH SPEED
RECOIL SPRINGS
Great story: Our spring maker is a gun buff.
He tried one of these springs in his 1911 and
had to call us to tell us how great it is. Our first
overwhelmed customer on this product.
$3.95, 3 for $8.45, 10 for $22.95 C45126
SPECIAL .45 COLT AUTO
REPAIR PARTS KIT
Containing the following parts: 4 grip screws, 2
grip screw escutcheons, 2 mainsprings, plunger
tube spring, sear spring, 2 ejector pins, 2 mag.
catch springs, 1 firing pin stop, 2 firing pin
springs, 4 hammer strut pins, 2 firing pins, 2
mainspring housing pins, 1 recoil spring. Regular
$37.00 SPECIAL $22.50 C45091
SUB COMPACT 1911
MAINSPRING HOUSING
These are the checkered flat
housings made from reinforced
nylon, complete with 2 plungers and spring. Also useful for our Para
Ordinance frame casting projects. Good for
replacement or the custom build. 2 sizes.
1.632" High.......................... $9.95 C45302
1.357" High.......................... $9.95 C45303
Also have the 1.357" unit with vertical
grooves rather than checkering if you wish
.............................................$9.95 C45311
Just in the door!
NEW
.40 S&W, 9MM & .38 SUPER
ITEM!
FIRING PINS – Now available
for 1911 pistols......................... $5.95,
3 for..............................14.95 C45301
Will fit both 70 Series and Series 80 pistols
.45 BARREL BUSHING WRENCH
$2.95 Free Bonus –
Other end is an M16
shorty buttstock installation wrench TOOL031
.45 AUTO SPRING KIT
WW2 GERMAN M35 HELMET
Model 1935
German
helmet with
rolled edge,
metal banded
liner with 8
tongue leather
liner and
leather chinstrap assembly mounted by
3 rivets on the 1.7-1.9mm thick steel
shell in German ‘Feldgrau’ green color.
Helmet fits 7-1/4" to 7-5/8" head size
(large). New, well made and great for
static displays or reenactments. We have
purchased the remaining stores of these
from ‘Kamabee Keep’ along with various
German helmet decals which we are using to provide one set of helmet decals
with each helmet at no charge as long as
supplies last. M35 helmet with decal:......
$49.50 HLM037
(Sorry, no choice on decals as they are
quite limited)
WWI AUSTRIAN HELMET
Authentic to the First
World War Austrian
issue infantry helmet,
this late mfg. steel
helmet w/leather liner
and canvas / leather
chinstrap has similar
markings inside the rim
and is the same weight as used by troops
on the Western Front, Eastern Front
or in the Italian Alps. It was preferred
over the German version because of its
smaller brim, but still sported two helmet
plate lugs in case the brow plate was to
be used. Difficult to find now days, our
Austrian helmet is a splendid accurate
rendition of the combat helmet worn
almost 100 years ago! Austrian Helmet....
$68.00 HLM023
MAKAROV GOODIES
Phones Open: Mon Fri, 8:30am – 5:00pm
Showroom Open:
Monday - Saturday,
10:00am – 5:00pm,
Friday til 8:00pm
ORIGINAL NEW 6in SLIDE 1911
RECOIL SPRINGS
Spare magazine, original.......... $24.95 RPM268
Original new holster.................... $2.95 HOL018
Original new shoulder holster..... $9.95 HOL008
Original new Makarov lanyard
.................................................$4.50 MAK010
Special set of all 4 items - Value $39.00. Set
Special.......................................$32.00 MAK011
Also have some Makarov parts – email or call our
parts department.
One each of all 6 springs in a Colt .45.
A $13.25 value for only. Includes sear spring
$7.75 ea. C45002, 10 sets for $65.00, 100
sets for $450.00
SUPER SPECIAL
All 3 kits of springs, pins & screws above for the
1911 Colt. Sale value is $18.65. Super Sarco
Value $14.95 for all 3 sets C45259
FRONT TACTICAL COMBAT SIGHT FOR
1911 FOR DOVETAIL SLIDE
170" height .135 blade width. For
standard 1/4" dovetail red highlight on
back. SARCO PRICE $4.95,
3 for $9.95 C45140 (Comparable
price $19.95)
1911 combat sight set millet rear sight
plus (tactical) wide blade front with
1/4" dovetail red highlight Retail value
$62.00. Sarco Special $19.95/set,
3 sets for $42.50 C45177
MILLET MARK I
Combat High Profile Rear White
Outline Sights Fits Colt 1911
dovetail. White outline gives
clear sight picture. Retail value
$22.75. C45131
Sarco Special $9.95, 3 for $24.95
Full pin set for Colt .45
NEW!
Auto. All seven pins for the
ITEM
M1911. New $4.85/ set,
10 sets for $38.50,
100 sets for $285.00 C45195
U.S. MILITARY FLECHETTES PACK
Historically used
through the ages
for defense, these 1 inch long Flechette Darts were thoughtfully saved
from Beehive munitions. Since we
have a limited supply, we are offering
you a 2 oz. pack which holds about
100 flechettes $7.00/2oz pack
(100+pcs) MISC288
Save BIG when you buy a POUND!! 1
LB/$24.95 MISC307
Enfield parts, parts & more parts!
NOTE: We have most all parts for #1 MKIII, #4
MKI and #5 Enfield– along with many variations &
accessories. Check our website.
Enfield questions? Email Lucas for
answers! Lgreb@sarcoinc.com
H2
50 Hilton Street, Easton PA 18042
www.e-sarcoinc.com / www.sarcoinc.com
610.250.3960 Fax: 610.250.3961
ENFIELD PARTS & ACCESSORIES
RARE STOCK SET
(stock, forend & HG’s) for #4 MKII Enfield
(trigger on the receiver) – New condition. Need
to stain to match. Without cross bolt
.................................... $140.00 LE4074
#4 MKII Stock Set, used w/o cross bolt
..................................................... $109.95
#4 Standard Enfield Stock Set, used
........................................................$99.95
ENFIELD .303 MAGAZINES
10 round magazines for the MKIII SMLE rifle
.........................................$50.00 RM011
Also have a few of the early version of this magazine,
marked “2” or “3” on rear rib and has rotation follower
retaining tab........................................$65.00 RM012
Original 10 rd. mag for #4 Enfield....... $50.00 RM015
.303/.308 Magazine...........................$59.95 RM039
Complete set of #1 MKlll stock hardware–
buttplate, swivels, forend collar assembly,
bands, nose cap, rear sight protector,
stock bolt and all related parts. 27 parts
$48.50 LE3094 See our website for complete
list of parts in kit
STAINLESS STEEL 1911 PARTS
C45038 Recoil spring guide (matt finish)
Commander................................... $3.50
C45299 Ambidextrous slide stop matte
finish.......................................... $12.95
C45150 Reverse recoil spring plug.............. $6.95
C45312 Hammer pin.................................. $2.00
C45313 Mag catch lock.............................. $3.00
C45314 Mainspring Housing pin................ $2.00
NICKEL .45 PARTS 1911
C45315 Slide stop................................... $15.00
C45316 Barrel bushing.............................. $8.50
ENFIELD STRIPPER CLIPS
We just bought the last small quantity we know of.
They are now dinosaurs. While they last!
................................................ $3.00 ea. STC010
ORIGINAL # 4 ENFIELDS
BAYONETS & SCABBARDS
Std MK II bayonet w/MKI scabbard
$12.50 BAY106
BRITISH STYLE ‘SAM BROWN’
BELT w/SHOULDER
NEW!
STRAPS – JUST IN!
ITEM
$44.95 MISC389
COMPLETE SET OF #4
ENFIELD STOCK HARDWARE
Buttplate, bands, swivels, handguard ring,
bolt and all related screws and washers. 17
parts...…$39.95 LE4103
See our website for complete list of parts in kit
ENFIELD RIFLE ID DISC
NEW!
ITEM
Brass 1 inch diameter disc which
is fitted into the right side of the
Lee Enfield Rifle stock. Frequently
found on British & Commonwealth forces
service rifles, these discs sometimes had
proof marks and or mfg. names, dates
etc. A great way to improve the appearance of the
Enfield Rifle. Engraved brass disc w/ 4 markings ....................................................$6.95 LE3084
THE NO. 4 ENFIELD TARGET/
MATCH SIGHTS
These sights were made by the famous British gun
maker. Parker-Hale, for use on a high power military
target rifle.
• Long range vernier micrometer sight
• Adjustments up to 1300 meters
• Micrometer click adjustments for windage
• Windage scale plate for possible adaptation
• Adjustable aperture disc that has six different
openings from .030 to .053
This has got to be one of the most outstanding Enfield
No. 4 micrometer target sights ever offered.
Note: The adjustable peep alone in
this sight costs $60.00
TO INSTALL THIS SIGHT ON YOUR #4
ENFIELD. TWO SIMPLE OPERATIONS ARE
NEEDED. Full and clear instructions are included for
the installation of this sight on your fine Enfield rifle. We
could have charged $100 to $125 for this fine sight, but
we’ll offer it now at only $69.95 PH007
ISHAPORE FRONT END FOR ENFIELD RIFLE
#1 MK3
Features the Indian squared
off style front sight protectors
and does not have a front sling
swivel behind the bayonet lug. Although it was
designated to accept DP63 designated bayonets
in the Indian Army, the lugs do in fact, attach the
British 1907, 1943, and Square Pommel bayonets
too. Original in very good condition. $12.00 LE3099
FULL ENSEMBLE/ENFIELD #32 MK1 SNIPER SCOPE
Outstanding detailed steel reproduction
telescope used on the Lee Enfield sniper
rifle. Ruggedly built , it has a sliding eyeshade, drum adjustments w/ distinctive
and solid clicking allowing for deflection of
16 minutes of angle left or right, as well as
elevation settings at 2 minutes of angle each. Range drum allows adjustments
at 50Yds per click out to 1000 Yds. Complete set comes w/ steel case, adjustment tool, scope mount, lens covers ..... and as a bonus Sarco includes 2 bases,
screws, taps and drill bits so you can install the mount. The Sniper Scope and
all the accessories for.............................................................. $595.00 N3207
COMPONENT PARTS AVAILABLE INDIVIDUALLY TOO!
1. #32 MK1 SCOPE by itself................................................... $399.95 SCP034
2. Set of rings & mount w/o bases......................................... $129.95 SCP001
3. Leather Lens Cover.............................................................. $21.50 SCP036
4. Front & Rear Base (Pads)...................................................... $39.95 LE4071
5. Drum Adjusting Tool............................................................ $22.50 SCP037
6. Transit Chest for scope...................................................... $139.95 SCP035
7. Full Set of Base Screws & Drills & Taps................................ $39.95 LE4075
Note:
ORIGINAL ENFIELD #32
SCOPES BRING UP TO
$7,500. W/CHEST. HERES
YOUR CHANCE TO BUILD
AN AFFORDABLE ENFIELD
SNIPER RIFLE!
BUILDING A #4 MKIT SNIPER RIFLE?
Mounting & tapping the bases is not easy. We got
a turnkey set for you – all one with the proper
British thread.
1. 7 proper screws (we send you 2 extra in case you
loose or mess up any)
2. The two taps you need with the proper thread.
3. The two proper drills you need for the job – .British size.............................................. $39.95 LE4075
Note: these tools are industrial quality and not
returnable. Set of 5 proper screws for the job w/o
the tools....................................... $14.95 LE4076
ENFIELD #4 MKIT SNIPER RIFLE CHEEK
PIECES
Just in the door!
Complete with
proper brass
screws. Use to
build your sniper rifle or also to create a
high comb buttstock...........$24.95 LE4106
BRITISH ENFIELD CANVAS SLING
We are now able to
offer you 3 of the
Wartime canvas
slings used on the
Lee Enfield Rifles
as well as 1 post
war issue sling.
These are new
made and all feature brass hardware and an accurate cotton weave.
Colors available:
TAN
SLNG102
Your choice…
BLACK
SLNG096
NEW!
$6.95 each
OD
SLNG094
RAF BLUE SLNG095
ITEM
BRITISH ENFIELD ACCESSORY KIT
Sling, firing pin tool,
oiler, field cleaning rod (pull
through), and brush. Value
$22, Special $16.95 LE4061
#5 JUNGLE CARBINE
BUTTSTOCK SET
NEW!
ITEM
NEW!
ITEM
Late production. New proper configuration buttstock with complete
buttplate and pad your original
forend & handguard can be modifed $39.95
LE5001 Does not include forend & handguard
MLE –SMLE PATTERN 14 SLING
This sling is a reproduction of the Pattern 14 leather
sling used for the SMLE (Short, Magazine Lee Enfield) starting in 1914, also known as the “Austerity
Pattern”, a shortage of web gear forced the Brits to
re-introduce leather. Leather rotted in the trench environment so the Pattern 14 was used in second line
and rear echelons as much as possible. The generous 49 inches of length on the Pattern 14 was widely
used in both the SMLE and the MLE (Magazine, Lee
Enfield) 5" longer that the SMLE. This incredible
reproduction of the Pattern 14 sling, will look and
feel as authentic as the originally produced in 1914,
install it and show it off, a perfect companion for
your Lee Enfield............................$9.95 SLNG079
#4 MKIT ENFIELD SNIPER RIFLE SCOPE
MOUNT BASES
• (Also called the “pads”) • Front and rear pads (set)
LE4071 $39.95 (only have a few of the sets)
#4 MKIT SNIPER COMPLETE PROGRAM
Includes the scope mount, mounting bases (pads),
plus the 7 proper screw & 2 drills & 2 taps. This all
you need to build your # 4 MKIT Sniper on a
#4 Enfield rifle…$219.95, 3 for $624.00 LE4080
Special – complete scope mount with the mounting pad set................................$189.95 LE4081
ENFIELD #4 MKIT SNIPER SCOPE MOUNTS
These fine scope mounts are now in stock again.
Telescope mounts for the British Enfield #4 MK I (T) Sniper Rifle. We made
these because there are so many #4
MK I (T)’s that were imported with out
scopes. The good news!! These mounts
will take a standard commercial 1”
tube scope to use on your rifle while you are seeking
an original scope for the rifle. Made to meticulous
detail to the original as we have with all our reproduction scope mounts. Sold at a very special price
considering the rarity and value of an original mount.
$159.95 each SCP001 (Note - does not include scope
or receiver pads)
#1 MKIII & # 4 ENFIELD
SPECIAL ITEMS
LE3074 Brand new original G.I. Buttstock
#1 MKIII.............................................$19.95
LE3075 #1 MKIII complete Safety Assy............$16.50
LE3078 #1 MKIII Original brass buttplate.......$14.95
LE3076 #1 MKIII Enfield .22 LR cal bolts,
complete super rare........................ $100.00
LE4063 #4 MKI complete Safety Assy..............$16.50
LE4077 Original #4 Enfield brass buttplate VG.$14.95
LE4004 #4 Bolt head size # 1, new orig...........$24.95
3 for...................................................$64.95
LE4005 Bolt head for # 4 Enfield, new standard
............................................................$13.50
LE4062 Original pull thru field cleaning
device, new......................................... $2.95,
3 for..................................................... $6.95
LE5001 # 5 Complete buttstock assy for jungle carbine
–current production Includes buttplate assembly
........................................................... $39.95
MISC196Original Extractors for the .308 (7.62mm
Nato) cal #1 MKIII Enfield – These are
called the model 2A.........................$19.95
LE4096 Original Israeli # 4 Enfield scope rings for
the brass Israeli #32 scope for the Israeli #4
Enfield sniper rifle (few only).. $59.95/set
LE4010 # 4 Enfield striker (firing pin) new original
factory........................................... $17.50
LE4104 #4 Enfield L shaped battle sight
........................................................$8.00
LE4079 #4 Enfield stock & handguards set, used
..................................................... $99.95
LE3049 # 1 MKIII Enfield striker (firing pin) new
original factory.............................. $17.50
LE4014 # 4 Enfield complete bolt............... $90.00
LE3064 # 1 MKIII Enfield complete bolt...... $69.95
RM57 Just a couple - .45-70 magazine for Navy
Arms .45-70 Enfield...................... $85.00
LE4013 #4 Enfield extractor spring...............$7.85
LE3095 Rare long Lee and Lee Medford sliding dust
cover, few only.............................$100.00
LE3059 #1 MKIII Enfield extractor spring
.................................................... $10.00
G2
SARCO, INC.
BAYONET FROGS
50 Hilton Street,
Easton PA 18042
www.e-sarcoinc.com
www.sarcoinc.com
610.250.3960 Fax: 610.250.3961
We have 4 leather historical bayonet Frogs for wearing on waist belts.
A. SWEDISH MAUSER - original good condition........ $5.95 MSR258
B. JAPANESE ARISAKA - late mfg, new, for Type 38 & Type 99
bayonets................................................................ $9.95 BAY115
C. YUGOSLAVIAN MAUSER - original good condition
.......................................................................................................... $7.50 BAY054
D. GERMAN K98 MAUSER - late mfg, new, fits WWII K98 bayonets......... $9.95 MSR111
E-mail: sarcopa@sarcoinc.com
CARCANO CAVALRY CARBINE BAYONET FOR MODELS 1891 & 1938
As used by
paratroops and
specialized infantry. Faithfully manufactured
from an original. With scabbard. Great price
for a rare bayonet.............. $89.95 BAY245
FAL TUBULAR BAYONET
WW1 GERMAN TRENCH KNIFE w/
‘BOOT’ SCABBARD
ENFIELD #9 BAYONET
Original bayonet blade with
blood groove
used on the
#4Mk1 rifle and
Sten MK5 SMG.
Complete with scabbard.
.................................... $29.95 BAYO21
BRITISH SPIKE BAYONET
SCABBARD
GERMAN K98 BAYONET
Late manufacture K98 bayonet and scabbard. Early WW2 style with wood grips.
......................................... $34.95 BAY165
Socket style
bayonet as
used on
various SIG rifles and used by the French
military in the 80s. Comes with scabbard
......................................... $75.00 BAY130
Well crafted scabbard w/ leg tie
and metal reinforcements. WW2
design intended for use with the
M3 fighting knife, but works with
other similar sized blades like
standard M14 & M16 bayonets......................... $14.95 BAY184
ORIGINAL MOSIN NAGANT BAYONET FOR YOUR 91 or 91/30 RIFLE
Bayonet only.............................. $19.95 BAY019
Original Mosin Nagant Bayonet with new made
scabbard....................................$34.95 BAY084
Scabbard sold separately........... $19.95 N91081
G-3 RIFLE BAYONET / DANISH
CONTRACT
Sleek original
Danish G3
bayonet which is also great as a fighting Knife!
Marked with Royal crown on hilt / HMAK.
Comes with scabbard........... $65.00 ECK003
Original scabbard for #1 MK3 blade bayonets (@18"
length)
......................................................$24.95 BAY108
M1 GARAND BAYONETS
Sarco has a limited quantity of M1 Garand Bayonets in
both original, and new/late production versions with blade
lengths from 6.5 to @ 16 inches, sold with, and without scabbards.
A. Original 10" Model 1943, Unmodified Bayonet w/
scabbard................................................. $64.95 BAY193
B. Original 10" Model M1905E1, Modified Bowie blade w/
scabbard................................................. $64.95 BAY198
C. Original 10" Model M1905E1, Modified Spear Point
blade w/ scabbard.................................. $64.95 BAY194
DEAL:
Buy One each , of the above 3 bayonets w/ scabbards
............................................................................................................................................$174.95 BAY195
D. New Made 16” Model 1943 bayonet & scabbard................................................................... $29.95 BAY182
E. New Made 10” Model 1943 bayonet & scabbard.................................................................. $24.95 BAY183
F. Original M5A1 bayonet w/ M8A1 scabbard, GI....................................................................... $36.50 BAY189
ALSO….We have RARE M5A1 Garand bayonets marked KM5A1........................................... $59.95 BAY020
G. Original Korean Army version of the 1943/ 1905 blade shortened to their requirement of between 6.5-7"
length. These were imported from the military by Arlington Ordnance years ago, and we have found a handful
remaining in the warehouse. Complete with original Korean short scabbard........................... $49.95 BAY240
Also have a few original Korean scabbards by themselves.................................................... $14.95 ea. BAY135
Go to our website for a full
listing of all our variations
of 1905E1 and M1 10"
Garand bayonets and scabbards. Also the tech history
of the 1905 16" bayonet
and the variations of the
10" bayonet.
CMP Garand M1 M1943 & M1
10" blade bayonet repair kits,
grips & screw, lever, latch button & spring. All the missing
parts. These are nice repos –
small quantity only. We will use
most for our own bayonets. May
require minor fitting – we fit ‘em!.
........................$19.95 BAY199
BEAUTIFUL CURRENT PRODUCTION SCABBARD FOR
YOUR CMP AND COLLECTOR BAYONETS
M3 scabbard for 16"
M1942 bayonet
$12.95,
3 for $35.95 BAY176
Late manufactured steel blade and
leather scabbard as used in WWI
and even WW2 in North Africa.
Differs from the standard 1907 by
way of the quillon connection to the muzzle ring. Classic old
English style and looks great on the rifle!......$58.95 BAY244
SWEDISH MAUSER BAYONET M96/
M38
SPANISH FR8 MAUSER BAYONET
ENFIELD #5 JUNGLE ENFIELD
BAYONET
ENFIELD #4 SPIKE BAYONET
Accurate new
made bayonet
with steel
scabbard for
use on the
Jungle Enfield & Sterling SMG
................................$39.90 BAY145
BRITISH 1907 LEATHER SCABBARD
U.S. M6 LEATHER SCABBARD
1907 ENFIELD QUILLON BAYONET
Fits FR8 &
CETME rifles.
Comes with
scabbard
$24.95
BAY128
Original bayonet
without
scabbard.
........................................... $29.95 BAY01
Late manufacture steel blade
& scabbard based on the
original trench knife.
Sleek & utilitarian for
use on belt or
Boot!. Very nice low
profile 6" blade.
$39.95 BAY248
SIG 530/ 540/ 542 RIFLE BAYONET
Newly manufactured steel
scabbard. Perfect
replacement!
...................................... $9.00 BAY235
For use with M38
submachine gun.
Faithfully made
from an original.
With scabbard. Very hard to find
........................................ $99.95 BAY24
WW2 1938 CARCANO FOLDING
BAYONET
Original Vg/
Exc.
Condition.
............................$30.00 BAY251
Original early FAL bayonet for thin barrel, short
flash hider FALs and STG-58.
Bayonet w/ scabbard canvas belt connection
................................................. $19.95 BAY016
Bayonet w/ scabbard w/o belt connection.
..................................................$18.95 BAY171
Bayonet w/o scabbard.................. $9.95 BAY156
WW2 BERETTA 38 FOLDING BAYONET
SPRINGFIELD WOOD BAYONET GRIPS
New production, new condition wood
grips for the M 1905 pattern bayonet
as used on the M1903 Springfield rifle.
Fix up or up-grade your old bayonets
with these beautiful new grips. Heavily
grooved for better holding, just like
some originals we found and sent to
the wood workers to copy. Screw and nut
included. Ready to fit on to your blade.$9.95
per set or 3 sets for $24.95 GRP143
SPECIAL RARE COLLECTOR M1 GARAND BAYONETS.
FEW ONLY AVAILABLE.
Turkish contract Korean War........................................................ $70.00 BAY226
Greek contract complete with original Greek Scabbard................. $74.95 BAY238
M5A1 Garand Bayonet with aluminum grips-with original m8A1 scabbard
............................................................................................ $75.00 BAY200
Original Norwegian Kongsberg M1 Garand bayonet 1954 issue (only 12 available)
......................................................................................... $150.00 BAY239
(SEE OUR WEBSITE FOR FURTHER DESCRIPTIONS AND INFORMATION)
SKS SPIKE BAYONET, COMPLETE
Original and ready to install… $9.95 SKS03
CZECH VZ-52 BAYONET
Original with
attaching parts
ready to mount.
$45.00 BAY25
Original bayonet for the
Enfield #4MK1 rifle and
Sten MK5 SMG. Complete with scabbard.
$12.00 BAY106
1905 BAYONET PROJECT
Set of original and new
made parts for assembling
a 1905 bayonet. Years ago
we had 2,000 blades manufactured and rewelded onto
handles with great
success, allowing us
to sell 1905 bayonets again. Now we have a very
limited group of these complete sets of parts remaining. The handles and hilts are from original
U.S. bayonets that were demilled by the U.S. govt.
Grips and internal handle parts and blade are
new mfg. Set of parts:.................. $24.95 each,
Or 10 for................................... $199.50 BAY232
*Add a scabbard for........................... $9.95 ea,
or 10 for................................... $89.95 BAY233
M8A1 BAYONET SCABBARDS
M8A1 Scabbards to fit the following bayonets!
M5 & M5A1 Garand, M3 Trench Knife, M4 for M1 Carbine,M6 for M14 Rifle, M7 for M16
New Military Contract.............................................................................................. $17.95 ea
Excellent used military contract..................................................................................... $14.95
We have a small quantity of U.S. G.I. M8A1 scabbards. VG condition............................. $19.95
(Call Cholly for bulk purchases on M8A1 scabbard BAY083)
Original G.I. new M8A1 scabbard. Just found a few in the warehouse from the old days
.........................................................................................................$24.95, 10 for $199.50
BAY083
BAY191
BAY040
BAY041
BAYONET GRIPS & SCREWS
BAY164 Original Yugo ’98 Mauser bayonet grip sets.................. $5.95, 3 for $14.95
LE3083 Original grips for Enfield #1MKIII (1907) bayonet...................................$9.95
BAY163 Original new G.I. grip screws for 1903 Springfield & WWII Garand bayonet
..................................................................................... $3.95 ea., 4 for $10.00
BAY179 Original new grip set for the British #7 bayonet for the #4 Enfield...... $12.95
BAY215 New original G.I. left grip for the M1905 Springfield bayo - Special for that
special bayonet........................................................................................... $45.00
U.S. M3 FIGHTING KNIFE
Precision made M3 fighting knife with leather M6 scabbard
and leg strap. This is one of the best fighting knives of WW2
and perhaps one of the strongest too! Both scabbard and
knife are properly marked to include markings on the hilt,
blade and pommel and a date of 1943. The handle has been
constructed the same way the originals were with ‘coins’ of
leather tightly packed and symmetrically tapered like the original
...........................................................................................................$29.95 BAY180
COLLECTORS BAYONETS
VARIOUS COLLECTORS BAYONETS & ACCESSORIES
BAY031 SKS spike bayonet, stripped..............................................................................................$3.95
BAY125 Brown Bess Reproduction bayonet scabbard.....................................................................$9.95
BAY162 Nice repro of leather scabbard for the Trapdoor Springfield trowel bayonet – complete,
few only.................................................................................................................................. $24.95
ECK002 Swedish G3 Bayonet (3 crowns) with scabbard, new original – Few only......................... $65.00
BAY043 Perfect reproduction leather scabbard for 1941 Johnson rifle bayonet. Almost sold out –
can’t tell from original............................................................................................................ $29.95
BAY217 Rare find – found 15 only – M5 Garand bayonet with aluminum grips............................ $50.00
BAY172 New G.I. M16 bayonet in original, G.I. packaging............................................................ $34.50
M16 BAYONETS
Sarco is pleased to offer a selection of original
USGI, foreign military contract, and new mfg
bayonets.
A. U.A.E. (United Arab Emirates) M16 bayonet
with black synthetic scabbard. UAE emblem on
handle and also on scabbard. New/unused.............................................. $34.95 BAY237
B. USGI M7 Bayonet in very good condition with M8A1
Scabbard................................................................................................. $29.95 BAY001
*Also have a small number of the M7 bayonet in
Excellent condition with ‘like new’ scabbard............................................. $32.95 BAY003
C. Econo M7 bayonet w/ scabbard – these are not mil spec, but fit
and look like the M7 bayonet and scabbard. New condition..................... $19.95 BAY229
D. M9 type bayonet w/ scabbard – A terrific rugged
alternative to the very expensive GI issue M9. Features a 7 Inch stainless steel blade
sharpened to a razors edge with Sawback edging on the opposite side. Also has a
sharpening stone on the back and wire cutter connection, and spare pouch on the
scabbard. Also includes the quick release features on the belt fastener and blade release
................................................................................................................ $39.95 BAY219
I2
SARCO, INC.
Hilton
50 Hilton Street, Easton50
PA
18042Street, Easton PA 18042
www.e-sarcoinc.com
/ www.sarcoinc.com
www.e-sarcoinc.com
/
610.250.3960 Fax: 610.250.3961
www.sarcoinc.com
610.250.3960 Fax: 610.250.3961
E-mail: sarcopa@sarcoinc.com
JUST BOUGHT A DEAL ON M1
CARBINE WWII FLIP SIGHT
(L sights) The milling marks on
the bottom seem to indicate they
are original but we have no history – We’ll
sell ‘em like a repro (originals fetch $50,
more or less) CRB185 $19.95 3 for
$49.95
NEW M1 CARBINE BARRELS
Super Quality – Parkerized. Haven’t
had these in a couple years. While they
last. From latest military print. Shallow
chambered For proper head spacing.
$149.95, 3 for $424.95 CRB183
Others sell a new replacement barrel for
up to $250.00
M1 CARBINE BOLT ASSEMBLY &
DISASSEMBLY TOOLS
A “gotta have” for Carbine owners..
.......................... $22.50 CRB002
3 for............................... $59.95
Interesting note: The 2nd item
we ever listed for M1 Carbine
M1 CARBINE PISTON NUT WRENCH
Available again................$12.95,
3 for..................... $34.95 CRB003
CARBINE TOOLS & ACCESSORIES
Blank Adaptor.........$9.95
Magazine, 15 shot, new
............................ $11.95
Tool, trigger spring removal
...............................$3.95
Bolt Assembly tool
............................ $22.50
NEW M1
CARBINE TOOLS
JUST IN!
CRB093
CRB010
CRB004
CRB002
NEW!
ITEM
A. Front sight
installation tool
..............$26.50 CRB174
B. Front sight removal tool
..............$26.50 CRB175
C. Receiver wrench with barrel
block set for barrel removal
and installation
..............$49.95 CRB006
SPECIAL – Set of all A, B & C tools
....................................$99.50 CRB176
D. Rear sight installation adjustment tool
....................................$79.95 CRB177
SPECIAL – Set of all A, B, C,
& D tools above
.....................$159.95 CRB178
Sorry tools are not returnable
M1 CARBINE MAGAZINE
DUST COVER
Original rubber dust
covers back in stock
after many years! These
are G.I. and in excellent condition. They
fit easily over the top feed area of the
magazine.…
5 pcs. for.................................... $4.95,
10 pcs. for..................................$7.95,
25 pcs. for.................... $14.95 CRB095
M1 CARBINE SPRING & PIN KIT
All the pins & springs in a M1 Carbine
..............… $9.95, 3 for $27.95 CRB173
M1 CARBINE RECOIL CHECK
New, G.I. style “muzzle brake”,
clamps onto muzzle of any
G.I. M1 Carbine. Designed to
reduce recoil on the M-2 Carbine.
Marked “Check, Recoil M1” on bottom.
$29.95 ea. CRB102
M1 CARBINE PARTS & ACCESSORIES
OUR FAMOUS M1A1 PARATROOPER
CARBINE STOCKS AVAILABLE AGAIN !!
This is a perfect and exact reproduction of the WWII M1A1
Paratrooper Stock. Each stock has a matching handguard,
so your treasured carbine will look beautiful.
(See website for other M1A1 Stock Parts)
M1 CARBINE FLASH HIDERS
New, G.I. style flash
hider, clamps easily
onto the muzzle of any
G.I. type M1 Carbine Marked “Hider,
Flash M3” $29.95 CRB097
SPECIAL! Flash hider recoil check combo
$52.95 CRB132
GOOD NEWS!! WE NOW HAVE
12 PHONE LINES TO BETTER
ASSIST YOUR CALLS!!
Available Again
M1 CARBINE BANDS
First model barrel band assembly
with swivel and screw. Perfect
for restoration of an early WWII
pattern carbine. New.
$19.95 ea. 3 for $56.00
Just bought a good deal on 1st model M1
Carbine barrel bands and will pass it on to
you. Previously $20-$25 ea, now!!
$14.95, 3 for $39.95 CRB023
3 for
This is absolutely the best quality available
(Gun Not Included)
Other Accessories Available: Carbine Stock Pouch $9.45 CRB134
Sling and Oiler $10.95 CRB088
Bulk buyers of this great stock, call Dave or Cholly.
PREMIUM M1 CARBINE STOCK SET - Back in stock again!
Beautifully crafted Birch wood stock and handgaurd enhanced with a walnut stain
that really makes the wood grain stand out. Just the right mix to make your military
M1 look like GI issue, but with a quality edge in appearance. Properly channeled for
an easy installation of your existing barreled receiver. Great chance to put new life into
your M1 Carbine and also increase its value!..................................... $79.95 CRB190
We have M3 sniper scopes and
one super rare M2 sniper scope in
stock. Also new original G.I. parts –
Check our website or call MG Dave
M1 CARBINE SPRING KIT
NEW!
A put-away special: slide stop,
ITEM
recoil, extractor, ejector, sear,
hammer trigger, & mag catch
spring $14.00 value. Only $6.95, 3 for
$18.95 CRB137
Set of both of above
...................$18.95 CRB180
M-1 CARBINE POUCHES
& MAGAZINE SETS
Individual pouches for sale as well as combination
sets with magazines. Every order with magazines
gets a free original USGI rubber dust cover with
each mag.!
1. CARBINE STOCK POUCH - holds
2-15 rd. magazines and slides onto
the wood stock. New repro. With
markings on front & back................ $9.45 or
3 for.......................................$24.95 CRB134
( pictured on Left )
2. CARBINE BELT POUCH - holds 2-15
rd. magazines and slides onto belt.
New, GI.................................... $8.00 CRB092
3. CARBINE BANANA CLIP POUCH holds 4- 30rd. magazines. Slides onto
belt...............$9.95 or 3 for $24.95 CRB090
( pictured on Right )
____________________________
4. COMBO A: 2- 15 rd. Magazines and
Stock Pouch w/dust covers
..............................................$29.95 CRB191
5. COMBO B: 2- 15 rd. Magazines and
Belt Pouch w/dust covers
..............................................$28.95 CRB192
6. COMBO C: 4- 30rd. Magazines and
Banana Clip Pouch w/dust covers
..............................................$69.50 CRB193
*Follow State & Local laws when ordering
magazines*
ORIGINAL BOX OF 100 DUST
COVERS
CRB068
CRB063
CRB065
CRB064
CRB069
CRB078
CRB080 CRB079
CRB082
CRB083
CRB184
CRB044
CRB046
CRB041
CRB042
Ejector Spring............................. $1.50
Extractor.................................. $12.00
Extractor Spring.......................... $1.25
Extractor Spring and Plunger
................................................... $3.50
Firing Pin................................. $17.50
Front Sight Key........................... $2.75
Front sight............................... $12.50
Front Sight Pin............................ $1.25
Gas Piston................................ $11.50
Gas Piston Nut............................ $6.00
Handguard rivets............ 20 for $5.00
Hammer................................... $17.00
Hammer Pin................................ $1.50
Hammer Spring........................... $2.50
Hammer Spring Plunger.............. $4.75
M1 CARBINE SCOPE MOUNT
Installs in seconds with no special tools. No drilling
or tapping. Fits all G.I. or commercial carbine only
$11.95 $17.50 CRB103
Scope mount with 1” rings
$15.95 $22.50 CRB104
Special of the Month
Original military cartridge deflector
for M1 Carbine – fastens to top of
receiver w/wire form
“grippers” to deflect
NEW!
fired cases to right of
ITEM
gun – keeps ‘em out
of your line of sight.
New surplus.....................$7.95,
3 for...................$19.95 CRB096
M1 CARBINE MILLED
NEW!
ITEM
REAR COMBAT SIGHT
Back in stock
................... $29.95 CRB154
ORIG WWII G.I. M1 CARBINE KHAKI
CLEANING ROD POUCH
New cond. Few only. WWII markings.
Found in the warehouse
$9.95 CRB172
NEW FLAT (WWII STYLE) M1
FORGED CARBINE BOLTS
Stripped $59.95 CRB070
Complete $89.95 CRB072
M1 CARBINE PROJECT BARRELS
These are new barrels in process from the old PMC Carbine Factory. Bought
‘em 30 years ago. Just dug out of the warehouse. These are fully profited and
threaded but have no chamber or gas block. Barrel is milled for front sight key
slot… $29.95 CRB194 Your choice with gas port hole or without.
*Front sight key slot is milled.
M1 Carbine fans will love this deal! Original G.I. cardboard box containing 100
pcs. of the rubber carbine dust cover
..................................... $25.00 CRB188
Check our website for new 15 & 30 round
Carbine magazines – In stock – GI pattern
CRB010 15rd magazine...................... $11.95
CRB008 30rd magazine...................... $14.95
Ordering instructions are in the ad or on our
website
These are truly Scarce as Hens
Teeth! For whatever reason there
are very few
of these remaining on the collectors market so we have thoughtfully
had them made from an original
utilizing strong leather, brass cover
and correct fasteners, and markings. This was used by Cavalry, on
motorcycles, jeeps, half-tracks etc.
Originally made for the full stock
M-1 Carbine, it also fits similar
sized firearms like the Ruger®
10/22® with the Sarco stock. Originals can fetch $400-$700. Sarco
brings this quality leather item to
you at the fabulous price of
............................$57.95 CRB189
Front 2" of a Carbine receiver
......................................... $12.50 CRB028
Sheared rear end of a Carbine receiver –
sheared in front of rear sight base
......................$9.95 CRB179
SLING AND OILER SET
OILER ONLY..........................$4.95 ea.
50 for................................... $149.50
100 for......................$275.00 OIL019
SLING ONLY..........................$7.95 ea.
50 for................................... $300.00
100 for...................$350.00 SLNG005
Early WWII pattern Khaki color M1
Carbine sling.................... $9.95 SLNG006
Gun not included
M1 CARBINE RECEIVER DEMIL FRONT
WWII PATTERN M1 CARBINE CARRYING CASE
M1 CARBINE REAR
ADJUSTABLE SIGHTS
New condition
$17.50 CRB155
M1 CARBINE PARTS
CRB090 Banana Clip Pouch...................... $9.95
CRB023 Barrel Band 1st Model.............. $14.95
CRB036 Barrel Band Retaining Spring
................................................... $3.85
CRB025
Barrel Band w/Bayo Lug New, G.I.
Parkerized................................ $19.95
CRB093 Blank Adapter............................. $9.95
CRB002 Bolt Assembly & Disassembly Tool
................................................ $22.50
CRB096 Brass Deflector............................ $7.95
BRUSH-001Bronze bore brush 30 cal
............................................. 10/$9.95
CRB035 Buttplate (Nickel)...................... $10.00
CRB032 Buttplate (Used).......................... $8.00
CRB031 Buttplate Screw........................... $1.50
CRB094 Carrying Case........................... $17.50
CRB028 Demilled Front Reciever M1/M2
................................................ $12.50
CRB067 Ejector........................................ $4.00
CRB066 Ejector and Spring....................... $5.00
$149.95
$399.95
CRB098
M1 CARBINE SLINGS
AND OILERS
$10.95 ea.
50 sets for $349.50 ($7.00/set)
100 sets for $599.00 ($6.00/set)
CRB088
WWII M1 CARBINE
LEATHER SCABBARD
CRB099 M1A1 Carbine Forend............... $95.00
CRB100 M1A1 Pistol Grip Current Production
................................................ $19.95
CRB056 Mag Catch................................ $10.00
CRB058 Mag Catch Spring and Plunger
................................................... $3.25
CRB057 Mag Catch, late w/mag support
................................................ $10.00
CRB135
Mag Spring puttaway New G.I. M1
Carbine 15 rd ............................. $2.95
........................................... 3 for $5.95
CRB070 M1 Bolt, stripped...................... $59.95
CRB072 M1 Bolt, complete..................... $89.95
CRB167 M2 Carbine standard walnut Stock
................................................ $44.50
CRB062 M2 Trigger Housing.................. $80.00
OIL019 Oiler............................................ $4.95
CRB109 Orig G.I. Inland T-3 Carbine scope
mounting bar.........................$800.00
These are a very close copy of the World War II M1
carbine case. Made from the same type and color
heavy cotton O.D. duck, with proper brass zipper
and leather tabs, this case is even “U.S.” marked,
as were the originals, carrying strap included.
Will hold all M1 and M2 carbines. Ideal for storing or carrying your carbine; for reenactors and
collectors. New condition SALE!! $17.50 ea. 3
for $47.50 CRB094
CRB142 Orig new G.I. M3 sniper scope battery
charging rack. Charges 8-10 batteries.
New G.I. in crate can ship UPS (136#)
.............................................$295.00
CRB014 M2 Potbelly stock, used G.I. walnut
................................................ $49.50
CRB154 Rear Sight, milled..................... $29.95
CRB155 Rear Sight, late stamped........... $17.50
CRB001 Recoil Plate.................................. $9.95
CRB030 Recoil Plate Nut........................... $2.75
CRB029 Recoil Plate Screw....................... $2.25
CRB020 Recoil Spring (Hi-Speed)
................................................... $4.50
CRB021 Recoil Spring Guide
................................................... $6.00
CRB022 Recoil Spring Housing (Early)
...................................................$22.50
CRB019 Recoil Spring Std......................... $3.75
CRB055 Safety (Flip Type)...................... $10.00
CRB059 Safety Spring and Plunger
................................................... $2.95
CRB103 Scope Mount............................ $11.95
CRB104
CRB049
CRB050
CRB051
CRB015
CRB016
CRB017
CRB018
CRB088 SLNG006
SLNG005
CRB052
CRB043
CRB048
CRB053
CRB004
CRB038
Scope Mount w/Rings.............. $15.95
Sear............................................ $9.50
Sear with hump........................ $12.00
Sear Spring................................. $1.50
Slide M1................................... $65.00
Slide, G.I., late M2
................................................ $75.00
Slide Stop.................................... $2.95
Slide Stop Spring......................... $1.50
Sling and Oiler Set
................................................ $10.95
Sling Khaki (New Reproduction)
..................................................... $9.95
Sling O.D. (New Reproduction)
................................................... $7.95
Trigger...................................... $14.95
Trigger Housing Pin..................... $2.00
Trigger Pin................................... $1.25
Trigger Spring............................. $3.75
Trigger Spring Removal Tool
................................................... $4.85
Selector Spring............................ $4.00
J2
SARCO, INC.
Phones Open: Mon - Fri,
8:30am – 5:00pm
Showroom Open:
Monday - Saturday,
10:00am – 5:00pm,
Friday til 8:00pm
50 Hilton Street, Easton PA 18042
www.e-sarcoinc.com /
www.sarcoinc.com
610.250.3960 Fax: 610.250.3961
E-mail: sarcopa@sarcoinc.com
U.S. M1903 & 03A3 RIFLE PARTS
Note: Almost all of our Springfield parts are original, new G.I. bought 30-40 years ago.
See our website for 1903 Springfield Drill Rifle Barrels SPF271
1903A3 SPRINGFIELD HANGUARD
New manufacture! Spruce up that Springfield
with a new wooden 03A3 handguard with both
metal clips installed. You’ll be very glad when you replace your dinged, splintered, or
split handguard with our fresh stained replacement. Excellent quality $19.95 SPF377
1903 & 1903A3 SPRINGFIELD STOCKS
A. Good, may have arsenal repair, straight stocks................................................... $75.00 SPF118
B. Select, much better than A. Nicer finish. Only very minor or no repairs, straight stocks
........................................................................................................................ $125.00 SPF116
C. WWII scant stock (semi PG) V.G........................................................................ $125.00 SPF144
D. Composite Springfield drill rifle stock & handguard, exc cond
........................................................................................................................... $39.95 SPF257
E. Good cond composite stock and HG..................................................................... $29.95 SPF362
F. Rough composite stock and HG........................................................................... $19.95 SPF363
G. Original finger groove stock, good condition as # 118 above
........................................................................................................................ $145.00 SPF267
H. WWI straight grip finger groove, reproduction stock.......................................... $160.00 SPF251
I. Original new G.I. unissued walnut 1903 & A3 Springfield scant stocks – also
called semi P.G.................................... $199.95 SPF259 might have slight rusting on cross bolt.
SPRINGFIELD M2 .22 COMPLETE BOLTS
Few only, found in pile. VG to Exc. These
come with a new original correct copper
headspace jam screw – not installed…
$250.00 SPF216
See our website for all M1 & M2 .22
Springfield parts.
M1903 TRIGGER GUARDS
(NOT STAMPED 03A3 TYPE)
Absolutely beautiful repro of 1903 Springfield milled
trigger guard. Can’t really tell from original. Replace
the stamped ‘A3 guard in your rifle with one of these
beauties. Finished in matte black, stripped (no floorplate) $49.95 ea. SPF117, Complete assy – trigger
guard with floorplate & catch assy $69.50 SPF343
SPRINGFIELD 1907 SLINGS, LEATHER –
AS USED IN WWI & WWII
1.
2.
SLNG024 WWI Model 1907 Sling (w/ brass
hardware and WWI date)........$16.95 ea.
3 for.............................................$47.95
SLNG025 WWII Model 1907 Sling (w/ steel
hardware and WWII date).......$16.95 ea.
3 for.............................................$47.95
1903A4 Springfield Scope and
Mount available – See our website
ORIGINAL TYPE SLINGS FOR
SPRINGFIELD TRAPDOOR
& KRAG RIFLE
Beautiful work – in stock again
$24.95 SLNG030
1903 Springfield original pattern
cartridge belts – over a year in development. Fabulous exact replica 1903
Springfield Cartridge belts. Complete
with the clip tie down tabs.
Color is early khaki rather than the O.D.
color we made the Garand belts in. This
reproduction is just as good as our Garand
belt, which we sold 1000’s of without a
single return. We have received our first
small shipment.
WINCHESTER LATE MODEL 66,
73, & 76 CARBINE COMPLETE
REAR SIGHTS
Perfect repro - resurrected
from 20 years ago – These
no longer exist $29.95
SGHT12
SPRINGFIELD HANDGUARDS
SPECIAL OF THE MONTH
$24.95 ea., 3 for $67.50 SPF146
1903 SPRINGFIELD
SPF001 Band Front Sight 1903............................$13.50
SPF002 Band Front Sight 1903A3........................$12.00
SPF253 Band Lower, new GI blue 1903................$25.00
SPF011 Band Lower (milled) 1903........................$20.00
SPF012 Band Lower w/Swivel (milled) 1903
...............................................................$23.95
SPF014 Band Lower w/Swivel (stamped)1903A3.......... $17.50
SPF018 Band Screw Upper Band 1903.................. $3.00
SPF019 Band Screw Upper Band 1903A3.............. $3.00
SPF263 Band & Hardware Set, milled 1903.........$54.95
SPF265 Band & Hardware Set, 1903A3....................... $49.95
SPF003 Base rear sight (not sleeve)......................$12.00
SPF306 Bolt, early smooth body, bent handle.......... $125.00
SPF374 Bolt, early smooth body, Nickel Steel.......... $200.00
SPF004 Bolt Late (complete).................................$42.00
SPF005 Bolt Late (stripped)..................................$20.00
SPF385 Bolt sleeve complete w/lock assembly & safety
...............................................................$26.95
SPF008 Bolt Sleeve (stripped)...............................$15.00
SPF009 Bolt Sleeve Lock........................................ $4.75
SPF010 Bolt Sleeve Lock Spring............................. $1.75
SPF384 Bolt sleeve w/lock & spring......................$19.95
SPF352 Bolt stripped & welded in firing pin hole
1903(A3)................................$3.95, 5 for $14.95
SPF351 1901 era, Springfield bolt body, smooth, not heat
treated.................................................. $300.00
SPF357 Bolt R marked for early Remington 1941-42,
stripped...................................................$65.00
SPF358 Bolt BF (Barney Forge) Springfield 1941 & 42,
stripped...................................................$45.00
SPF359 Bolt 1903A3 SA stripped for early A3’s
................................................................$45.00
BRUSH-001 Bronze bore brush 30 cal................. 10/$9.95
SPF091 Butt Swivel (milled) 1903........................... $6.50
SPF061 Butt Swivel (stamped) 1903A3................... $5.00
SPF016 Buttplate (milled) 1903(used)...................$20.00
SPF291 Buttplate New G.I. milled 1903................$30.00
SPF015 Buttplate (stamped) 1903A3 used............$15.00
SPF121 Buttplate Milled fine checkered
...............................................................$34.95
SPF257 Springfield Composition Drill Rifle Stocks,
G.I., used, VG-Exc...................................$34.95
SPF020 Cutoff....................................................... $8.50
SPF021 Cutoff Plunger........................................... $2.00
SPF023 Cutoff Screw............................................. $2.00
SPF024 Cutoff Spindle........................................... $3.50
SPF022 Cutoff Spring............................................ $1.50
Original G.I. walnut handguards.
M1903, New, unissued................ $14.95 HNGD01
1903A3 used cracked repairable
10 for.............................................$59.95 SPF261
1903A3 plastic for drill rifle........... $15.00 SPF043
1903A3 used good....................... $14.95 HNGD03
1903A3 used VG-Exc .................... $19.95 SPF089
1903 handguard Type 2 (1910 to 1916)
........................................................... $150.00
1903 handguard NM............................... $100.00
SPF342 Die cast buttplate assemblies for 1903
Springfield - looks like a milled buttplate (new
orig). Super rare! Collector’s dream
................................................................. $35.00
SPF309 Early ‘03 bolt stop, new orig. G.I..............$16.00
SPF028 Ejector...................................................... $5.00
SPF029 Ejector Pin................................................ $2.00
SPF025 Extractor.................................................$14.95
SPF027 Extractor Collar.......................................$10.00
SPF026 Extractor w/ Hole....................................$16.50
SPF033 Floorplate (milled) 1903...........................$14.95
SPF034 Floorplate Catch Assembly........................ $8.75
SPF031 Follower (milled) 1903.............................. $7.00
SPF030 Follower (stamped) 1903A3.....................$10.00
SPF032 Follower Spring......................................... $4.00
SPF036 Front Sight Base Pin................................. $1.50
SPF035 Front Sight Blade 1903............................. $6.00
SPF333 Front sight blade 1903A3.......................... $5.00
SPF044 Front Sight Cover....................................$12.95
SPF093 Front Sight Key 1903A3 ........................... $2.25
SPF037 Front Sight Pin.......................................... $1.50
SPF039 Front Sight Screw 1903 ............................ $2.75
SPF038 Front Sight w/Stud 1903 ......................... $9.95
HNGD01 Handguard 1903 (new G.I.).....................$14.95
HNGD37 Handguard 1903 used cracked repairable
.........................................................10/$39.95
SPF084 Handguard Clips (Two Packs).................... $3.85
SPF043 Handguard Plastic (New) 1903A3 ............$15.00
SPF347 Lower band assy w/swivel, used orig
Remington 1903......................................$47.50
SPF348 Lower band screw, new 1903..................... $1.95
SPF349 Lower band screw, new 1903A3................ $1.95
SPF046 Mainspring................................................ $4.00
SPF339 1903 MKI Orig Sear & Trigger Assembly (for
Pederson Device).................................. $125.00
OIL035 Oiler, late plastic WWII, new....................$13.95
OIL015 Oil and Thong Set (Metal)........................$35.00
OIL016 Oil and Thong Set (Plastic) Used
................................................................. $8.50
SPF094 1903 rear sight assy with windage screw without
barrel ring...............................................$39.95
SPF143 1903 rear sight windage screw................$12.00
SPF273 Rear sight band 1903 (Orig)....................$45.00
SPF370 1903A3 Rear sight, perfect repro.............$36.50
SPF371 1903 Rear sight complete assembly w/base &
windage screw (barrel ring not included).$49.95
SPF294 1903A3 Rear sight G.I. used....................$40.00
SPF065 1903A3 rear sight in wrap, Original G.I. new
...............................................................$50.00
SPRINGFIELD PARTS &
ACCESSORIES
ORIGINAL 1903 & A3 SPRINGFIELD STOCK
FRONT ENDS – removed
from original G.I. stocks.
These are cut just behind the band – you can
use these to fix your Springfield stock with a
buttered front end. Glue it under the lower band
so you cant see it. We cut ‘em off years ago.
We’re using them too..........................$34.95,
3 for...................................... $100.00 SPF372
CHROME SPRINGFIELD PARTS
SEE OUR WEBSITE
COMPLETE HARDWARE SET FOR
1903A3 SPRINGFIELD
Same list as parts to the left only 1903A3
late pattern. Value $55.00
Special $49.95 SPF265
1903 SPRINGFIELD LOW
SCOPE SAFETY ASSY
$14.30 SPF054
GERMAN WW2 RUBBER STAMP SET
(6 Pcs.)
Used for improving collection material
with worn or faded markings. These
stamps are perfect for marking canvas,
leather, paper etc. Use these with a standard
ink pad............................ $25.00 STAMP03
1903A3 PIN & SPRING KITS
All the pins & springs in a Springfield rifle – 03 &
A3 included $9.95, 3 for $24.95 SPF341
1903 SPRINGFIELD REAR SIGHT PARTS
SPF143 Screw, windage.......................................* $7.50
SPF094 r ear sight, complete without windage screw w/o
barrel ring, VG to Exc............................ $39.95
SPF264 R
ear sight complete w/windage screw & w/o
barrel ring........................................... $44.95
SPF273 1
903 sight base (around barrel).............. $45.00
* Above parts are new. Check our website for all other
‘03 sight parts
1903A3 SPRINGFIELD DRILL RIFLE BARRELS
These were removed from drill rifles & have their
chambers welded or have a rod in the barrel with
a small plug weld to hold it in. Front sight base
not included................................... $12.50 ea,
10 for..................................................$99.95,
50 for.....................................$400.00 SPF270
NEW!
ITEM
BRAND NEW 1903A3 SPRINGFIELD REAR SIGHTS ASSEMBLIES
Forgot we had ‘em................. $29.95,
3 for.......................... $84.95 SPF370
Original G.I. A3 rear sight new in wrap
................................. $50.00 SPF065
Original G.I. A3 rear sight used VG
................................. $40.00 SPF294
Check our website for A3 Sight Parts Have all parts
NEW GI SPRINGFIELD BARRELS
1.New G.I. 4 groove 1903 Springfield barrel, dated
1943. 1903 front and rear sight bases were added
as a modification for use as a 1903.
.................................................... $295.00 SPF386
2. M1903A3, New, G.I., 2 groove...... $199.00 SPF080
3. M1903A3, New, G.I., 4 groove...... $229.00 SPF130
M1903 & 03-A3 “SPRINGFIELD” RIFLE KITS
BORE CLEANING BRUSHES
.30 caliber brass bore brushes, new.
$9.95/10 • $39.95/50 •
$69.95/100
BRUSH-001
SPRINGFIELD STRIPPER CLIPS
Early brass WWI......................$4.00 ea,
5 for.................................$14.95 STC025
1903 SPRINGFIELD GRENADE
LAUNCHING BOOTS
A perfect reproduction of the
grenade launching rubber
boot (slip on) for the Springfield and M1 Garand. Absolutely meticulously beautiful!!
........................$34.50 MISC088
SPRINGFIELD PUT AWAY KIT 1/2 PRICE!
Trigger, 2 sears, 1 milled follower, 2 ejector, 2 strikers, 1
mainspring, 2 trigger pins, 1/2
price special. $15.80 SPF095
NEW!
ITEM
EXTRA LONG REAR GUARD SCREWS
FOR 1903A3 RECEIVERS
The standard guard screw only goes up part way
in an A3 receiver. This screw fills the hole to make
your rifle more attractive. Haven’t had these for 20
years. The G.I. screws only engages a few threads.
$3.95 ea, 3 for $9.95 SPF360
1903 & A3 SPRINGFIELD SPRING KIT
A put-away for the future all springs in the
gun – bolt sleeve lock, main, cut-off, sear,
floor plate catch, & magazine follow $15.00
value – Only.................................... $4.45,
3 for................................. $11.45 SPF248
SPF049 Springfield Ring, Handguard to Receiver
1903A3..................................................... $6.00
SPF053 Safety Lock............................................... $8.00
SPF054 Safety Low Scope Type............................$16.50
SPF086 Screw Buttplate Large............................... $2.50
SPF085 Screw Buttplate Small............................... $1.75
SPF092 Screw Stacking Swivel 1903...................... $2.00
SPF056 Screw Trigger Guard Front........................ $3.00
SPF057 Screw Trigger Guard Rear......................... $3.00
SPF074 Screwdriver Three Blade............................ $9.95
SPF055 Sear.......................................................... $7.50
SPF072 Sear Pin.................................................... $2.00
SPF062 Sear Spring............................................... $2.00
SPF266 Set of G.I. Milled Trigger Guard, Floorplate,
Floorplate Catch Assy..............................$99.95
SLNG067 Sling keeper, ¼” for 1907 sling, orig, new GI
...................................... $5.95 ea, 2 for $9.95
SPF013 Sling Swivel for Band (milled) 1903
................................................................. $7.50
SPF067 Spring Band Retainer (milled)..................$14.50
SPF066 Spring Band Retainer (stamped)................ $4.00
SPF058 Stacking Swivel and Band (exact reproduc
tion) 1903A3 ..........................................$15.00
SPF350 Stacking swivel screw 1903A3................... $2.00
SPF068 Stacking Swivel Used G.I. (milled)1903
..................................................................... $9.50
SPF366 Stacking swivel and band assembly, 1903A3 G.I.
used........................................................$18.00
SPF367 Stacking swivel 1903A3 G.I. new............... $6.00
SPF335 1903A3 stamped replacement rear sight. Perfect
for drill rifles............................................. $5.95
3 for........................................................$14.95
SPF113 Stock cross bolt & nut............................... $9.65
SPF090 Striker...................................................... $7.40
SPF052 Striker Rod............................................... $6.00
SPF051 Striker Sleeve............................................ $3.00
SPF076 Trigger Grooved.......................................$13.95
SPF077 Trigger Pin................................................ $1.50
SPF075 Trigger Plain............................................. $9.95
SPF368 Trigger guard, 1903A3 used G.I.............. $32.00
SPF382 Trigger guard, 1903A3—Reparked.......... $36.00
SPF117 Trigger Guard 1903 type, Milled
...............................................................$49.95
SPF078 Trigger Guard 1903, Orig GI....................$95.00
SPF079 Trigger Guard (stamped) 1903A3
...............................................................$31.50
SPF083 Upper Band (stamped) 1903A3................$16.00
SPF082 Upper Band New (milled) 1903................$30.00
SPF081 Upper Band Used (milled) 1903...............$20.00
These kits consist of every part of the “Springfield”
rifle except the stock, receiver, and barrel assy. (w/sight bases).
Kits will have bolts, bands, stamped trigger guard, swivels, trigger,
etc. Use these kits to build up to a rifle on your receiver or to rebuild an old ‘03.
All parts are in new or like new condition.
M1903 KITS
A. Parts kit includes new handguard..$159.95 ea. SPF127
M1903A3 KITS
A. Parts kit.........................................$149.95 ea. SPF126
C. For a new G.I. 2 groove 03A3 barrel add........ $190.00
Barrels only sold at this price with kit purchase.
Note: Rear sight parts may be used G.I.
FALL SPECIAL!!
Add a new Springfield stock & handguard set to
either Springfield kit (1903 or 1903A3) for only:
1903........................................ $149.00 SPF380
1903A3.................................... $159.00 SPF381
Price only good with a Springfield kit purchase.
CLEANING RODS FOR
RIFLES, PISTOLS & MG’S
CLN039 .22 cal 3 pc M16 or Galil (or other) cleaning
rod – round swivel handle (Israeli G.I.)
.................................................................. $3.95
CLN013 98K Mauser,10".................................$12.00
CLN014 98K Mauser,121⁄2".............................$12.95
CLN023 AK47................................................... $9.95
CLN026 Brazilian Mauser M1908....................$12.50
CLN032 Browning M1922 .32 Pistol.................. $2.95
CLN016 G33/40..............................................$14.95
CLN015 G43/K43...........................................$14.95
CLN025 GEW 98, 15" WWI..............................$12.50
CLN007 M10 Set for the M1 Garand................$12.50
CLN030 M16, 4 Piece Rod................................. $8.95
CLN033 S&W .38 Military................................. $2.95
CLN021 Swedish M1938 Rifles........................$12.50
CLN028 Thompson, Brass...............................$12.50
CLN027 Thompson, Steel.................................. $5.00
CLN018 VZ24 Mauser.....................................$13.50
CLN049 M93 Mauser......................................$10.00
CLN129 M95 Mauser......................................$13.50
CLN127 Turkish ’98 Mauser Model 38................ $11.95
SKS032 SKS original.............................................$9.95
CLN130 SKS 59/66 original............................... $12.00
CLN052 Uzi original...............................................$5.95
CLN022 Carcano Carbine, 2pc, original.............. $12.50
CLN132 M44 Finnish Mosin original................... $13.95
N91030 Mosin Carbine 1907 original................. $16.95
CLN133 Mosin Carbine 38/44 original................ $14.95
CLN045 Arisaka Type 99 Standard repro............ $16.95
CLN044 Arisaka type 99 Long rifle repro............. $17.95
FND011 FND sectional....................................... $15.00
CLN123 Beretta M38 SMG.................................. $14.95
CLN024 1891 Argentine Mauser......................... $10.00
CLN024 1909 Argentine Mauser......................... $10.00
CLN129 Chilean model 1895 rifle rod original...... $13.50
CLN131 Chilean 1935 Original............................ $25.00
CLN036 Carol Gustav SMG rod..............................$9.95
CLN128 36" One pc. .30 cal G.I........................... $13.95
CLN134 Steyr M95.............................................. $15.00
CLN046 Arisaka Type 1 & 2 Paratrooper rod....... $17.50
CLN147 Arisaka Transitional 99 rod, 4-7/8”....... $12.00
JAP3803 Arisaka Type 38 Long rod..................... $17.95
CLN148 Arisaka Type 38 Short rod..................... $17.50
CLN008 Arisaka Type 38 Carbine rod.................. $19.95
CLN149 RPD Cleaning Rod.................................. $14.95
1903A3 TRIGGER
GUARD ASSEMBLIES
A brand new complete assembly –
trigger guard + follower + spring + 2
screws -$51 value $39.50 SPF375
Complete assembly, used surplus - $51.50 value...
$39.50 SPF376
Trigger guard only, brand new..... $31.50 SPF079
Trigger guard, used G.I................ $32.00 SPF368
SPF344
SPF016
SPF015
SPF121
SPF342
SPF353
SPF355
1903 & A3 SPRINGFIELD
BUTTPLATE COLLECTION
New G.I. milled.................................. $30.00
Used milled buttplate........................ $18.00
Standard A3 used............................. $12.00
Milled fine checkered......................... $34.95
Original G.I. die cast buttplate.......... $39.95
Hand select Smith Corona buttplate
A3, used............................................ $29.95
G.I. stippled armorer match milled
buttplate........................................... $30.00
COMPLETE NEW SCREW SET FOR 1903 &
1903A3 SPRINGFIELD Includes:
Upper band screw
Rear guard screw
Front guard screw
3 Small buttplate and
Large buttplate screw
swivel screws
Stacking swivel screw
Cut off screw
Lower band screw
Note: the 1903 kit also includes the front sight screw
(value $23.00) SPF378 – screw set for 1903A3
.......................................................... $11.95
(value $26.00) SPF379 – screw set for 1903
.......................................................... $13.95
CMP SPRINGFIELD DRILL RIFLE
REPAIR KITS
All the missing or destroyed parts. Cut off,
Front sight, Cut off spindle, Bolt body, Cut
off plunger, Striker (firing pin), Cut off spring,
Stamped drill rifle rear sight $61.40 regular
value – Sarco Value..........................$34.95
3 sets for........................................$99.95,
10 sets for.........................$250.00 SPF361
03A4 SNIPER SCOPE MOUNT BASE
Late production military scope mounts for the 03A4
sniper rifle. Parkerized steel, unmarked. Will accept
Redfield rings (not included) $44.95 SPF136
U.S. SPRINGFIELD 1903 & 1903A3 “TYPE C” FULL
PISTOL GRIP STOCKS
FALL SALE ON C STOCKS!
These stocks will fit on the 1903, 1903A1 and the 1903A3. These will also fit on
your 1903A4 sniper rifle with small inletting for the bolt handle and is also correct
for the national Match rifle.
This stock was standardized in 1928 by the army for all Springfield rifles going
forward and was issued on all National Match rifles.
Crossbolt & nut included but not installed.
Guard screw bushing included
.............................................................. $179.95 $149.95 SPF276 (stock only)
Stock with new 1903A3 handguard.......................... $199.95 $169.95 SPF278
Stock with new original G.I. 1903 Handguard.......... $189.95 $159.95 SPF277
Hardware not included.
While these are truly “drop in stocks” we cannot guarantee proper
installation as it is beyond our control. Minor variations
occur in Springfields
SARCO, INC.
WW2 GERMAN M43 WOOL HAT
Excellent - new manufacture, earth brown
colored M43 cap with
two WW2 emblems.
We like this one best
as the color of the cap
goes well with most
clothing and it has a
functional chin and
ear protection flap
that is excellent
protection for cold
weather. Made
with a medium
weight wool so it
works in North
American climates
throughout the
year! Sizes 7-1/8",
7-3/8", 7-1/2",
7-5/8" $22.95
MISC345
M2
MAUSER PARTS &
E-mail: sarcopa@sarcoinc.com
ACCESSORIES
COMPLETE M-1 STEEL HELMETS
We have two varieties of U.S. M1
style helmets with
liner, suspension, chin straps,
and in the case
of our Vietnam
version, an original Mitchell Camo. cover.
These helmets have seen very little use
and are in excellent condition showing
perhaps some scuff marks, but no major
dents, dings, cracks etc., as are usually
found on M1 helmets from the U.S. and
Europe. The Mitchell camouflage helmet
covers are well used and may have some
blemishes, slight wear marks or minor
rips, but on the whole, are serviceable
and look like they served in Vietnam 40
years ago! Very difficult to find these
nowadays! A great gift for a war veteran,
Vietnam veteran, or anyone who served
up until the 1980s. Order our ‘Vietnam
Era’ version and get a free copy of one of
the Vietnam ‘Viet Cong’
free passes as dropped by aircraft on
enemy positions and also one version of
the notorious ‘Death Card’, left by some
U.S. forces after an engagement.
A. Olive Drab M1 style helmet complete
w/liner, chinstraps, suspension,
sweatband..............$35.00 HLM025
B. Vietnam M1 style helmet complete
w/liner, chinstrap, suspension,
sweatband and Original Mitchell
camouflage cover & band, and copies
of death card & Viet. pass
..............................$59.95 HLM026
RARE RIFLE STOCKS
HKR001 New original Hakim stock
........................................................ $175.00
FN49001FN 1949 .30-06 cal Good condition - will
rework well (we did one) – Complete with handguard set (not returnable)
...........................................................$75.00
FN49078FN49 .30-06 stock & handguards reworked in
our shop (this is a reworked #4)........ $125.00
SPF254
Bannerman Springfield stock model 1937
........................................................ $200.00
STK004
Remington model 1934 military rifle good
........................................................ $200.00
STK339 New original stock for Norinco JW15 .22 bolt
action clip fed rifle...............................$19.95
P14012 P14 Enfield stock w/handguards
........................................................ $149.50
P17044
P17, Front handguard new walnut......$19.95
P17045
P17, Front handguard used walnut
...........................................................$14.95
P17061
P17, Front handguard new hardwood
...........................................................$20.00
P17060
P17, Front handguard used hardwood
...........................................................$17.00
P17046
P17, Rear handguard new walnut........$26.50
P17047
P17, Rear handguard used walnut
...........................................................$19.95
P17062
P17, Rear handguard new hardwood
...........................................................$19.95
P17063 P17, Rear handguard used hardwood
............................................................$16.75
MSR549 Steyer 1912 (98 Mauser) Rifle Stock, good
condition.............................................$49.95
MSR366 1908 Brazilian long rifle stock good cond.
...........................................................$24.95
MSR366A A– Select (very few only) 1908 Brazilian
long rifle stock.....................................$75.00
MSR375 1908 Brazilian long rifle stock with handguard..................................................$39.50
MSR466 Select 1908 stock with handguard
...........................................................$85.00
MSR548 Steyer M1912 (98 Mauser) stock w/buttplate &
bayo lug..............................................$49.95
STK341 Stevens 416 .22 TGT stock VG used, orig
............................................................$50.00
STK342 Stevens 416 .22 TGT stock w/buttplate, new
orig......................................................$75.00
STK343 Remington 513T target rifle used VG – low comb
............................................................$25.00
STK344 Winchester G.I. model 75 target rifle, used VG
............................................................$35.00
STK345 Mossberg144 used exc.........................$35.00
STK346 Mossbert 144 used exc with “National Board
For The Promotion Of Rifle Practice” mblem on
the stock, used VG...............................$50.00
MAUSER “20” ROUND “TRENCH” MAGAZINE
During the trench warfare of WWI, the
Germans developed these magazines to
increase the firepower of their 98 Mausers. Easily installed in any GEW. 98 rifle
by merely removing the floor plate from
the rifle’s trigger guard, and replacing it
with the trench magazine. Original trench
magazines are very rare and valuable.
We now have this quality reproduction
identical to the originals right down to the
proof marks! Will also work in 98K, Kar
98a, Vz 24, and most M98 style Mauser
rifles. Blued steel, complete with follower,
spring and follower retainer with chain.
$75.00 MSR167 Available Again
Close Out –
Special of the Month
$49.95, 3 for $139.95
ORIGINAL NEW COMMERCIAL FN
MADE (FROM THE 60’S)
Note: These are original FN milled from
BAR stock – current offerings are castings.
Finally available again,
hooded bolt sleeve for use
with trigger mounted safety
mechanism. These are the
type used on all of the high
quality Mauser sporters. Our
sleeves are original F.N./Belgium manufacture, left
over from their production of Mauser Sporters several decades ago. We found a small cache of these
desirable hooded bolt sleeves at the FN plant and
bought them all. All are beautiful polished steel,
new condition. $29.95 each MSR119
MAUSER 98K WWII STYLE SLING
This sling has been most
carefully designed to duplicate the
original World War II German slings in every
detail. We have used a nice grade of dark brown
leather with the proper crossweave design. The
sling attachments have also been properly stitched
and crafted to duplicate the originals. These slings
have even been stamped with a wartime producer’s
code, date and eagle with Waffenamt marking.
$14.95, 3 for $39.95, 10 for $120.00
SLNG011NEW MAUSER 98K REPRODUCTION SLING
NICE REPRO OF K98 MAUSER SLING BUCKLE
Finally got these in stock
$4.95 ea, 3 for $11.95 SLNG081
MAUSER BOLT COLLECTION
We have over 30 variations of
Mauser bolts for your particular
Mauser – Check our website for
the full list of available bolts
98 MAUSER TACK DRIVER
HEAVY BARRELS
We took some of our fabulous Swedish 8mm
heavy barrels blanks – had them threaded for
98 Mauser actions. These have a nice heavy
profile and are 1 3/16" at chamber and 15/16"
at muzzle. Length is 22 3/8". Our barrel maker
commented “I would be proud if I made a barrel
of this fine quality” – These are fully chambered
but of course still need to be headspaced by a
competent gunsmith................. $79.95 MSR553
PLEASE NOTE:
These barrels have a slightly deep chamber for a
reason. If you have a shallow chamber, you will
need to use a chambering reamer to adjust headspace. With this method you can adjust head
space by turning back the shoulder and breech
a bit to accommodate the headspace dimension.
This also solves any variance from the chambering reamers pilot and the throat dimension in the
reamer. No need to buy a chambering reamer.
SEE OUR WEBSITE FOR THE FULL
SELECTION OF ‘98 MAUSER PARTS
MSR104
Band Retaining Spring, front GEW 98
........................................................... $4.00
MSR105
Band Retaining Spring, rear GEW 98.$4.00
MSR106 Band Spring (98K)............................. $7.00
MSR096
Barrel KAR88 Orig Used 8x57 171⁄2" small
ring.................................................$50.00
MSR304 Barrel, Verguiero 8x57mm 23-3/4” Small
Ring, New........................................$75.00
MSR097
Barrel KAR88 Original (hand picked bores) 8
x 57MM 17 1/2" small ring................$75.00
MSR114
Bolt (complete) turndown handle.. $125.00
MSR115
Bolt (stripped) turndown handle......$75.00
MSR117 Bolt Sleeve (new).............................$12.00
MSR118 Bolt Sleeve (used).............................. $8.00
MSR120 Bolt Stop (stripped)........................... $7.00
MSR121 Bolt Stop Assembly.........................$17.50
MSR359 Bolt Stop for 1909 Argentine stripped
.......................................................$14.95
MSR434 Bolt Stop Screw, new......................... $2.00
MSR122
Bolt Stop Spring..............................$12.00
MSR404 Bolt stripped, straight handle..........$43.50
’98 MAUSER SPORTER
RIFLE PARTS
Steel hinged trigger guard
$69.95 MSR326
Single stage trigger & sear
assy. Note this single stage
trigger & sear takes the creep
out of your trigger pull.
$6.50 ea. MSR205,
3 for $18.95
Low scope safety – for
scope mounting on 98 Mauser scoped
Sporter. Fits & works on standard military
bolt sleeve $17.75 MSR162
NEW ARRIVALS! RARE ’98
CONTRACT MAUSER SLINGS
Mauser Portuguese 1904, Verguiero
................................. $14.95 SLNG013
Brazilian M1908 detachable Sling Swivel
..................................... $8.50 MSR324
Proper parade sling loop for Brazilian
1908 to go with the butt swivel above
..................................... $4.00 MSR193
Set of above MSR324 & MSR193, only
..................................... $9.95 MSR415
Orig brand new Spanish Mauser Model
1893 & M1916 rifle sling
................................. $12.95 SLNG058
A GREAT BUY ON SELECT NEW
MAUSER ‘98 SPORTER
BARRELS
FROM A MAKER OF HIGH END MAUSER SPORTING RIFLES (HE CHANGED PRODUCT LINES SO
WE GOT THE BARRELS)
These barrels are custom produced
from the highest quality Swedish steel.
Nothing but the absolute best. Do to
our fabulous buy we can pass the savings on to you. Fits all ‘98 Mauser actions. Barrels are shallow chambered so
they can be head spaced to your action.
Compare price at $235.00 to
$255.00
Barrel dimensions: Length 217⁄8"
Muzzle diameter 5/8"
shoulder diameter 118⁄ "
Special prices cal .30-06 $64.95,
3 for $178.95 MSR350
BRAND NEW ORIGINAL 98
MAUSER STRAIGHT BODY
STRIPPED BOLTS
Just in the door as I am writing this. The
original FN production. These came out of
the FN Factory in a buy of left over parts
in the warehouse. Unnumbered. Never in a
gun. $49.95 MSR517
Extra Special – our new ’98 bolt a new
extractor and a new firing pin
......... $79.95 MSR518
K98 MAUSER SPARE PARTS KIT
Been out of these for
a while. Now’s a great
time to pick up a pack
of these original parts
before they are gone
again! Contains:
EJECTOR, FOLLOWER, MILLED, TRIGGER
SEAR, SAFETY, FOLLOWER SPRING, SEAR
SPRING, BOLT SLEEVE, FIRING PIN, FIRING
PIN SPRING $29.95 MSR370 VALUE $65.00
MSR123 Bolt, complete straight handle ........$79.95
MSR126 Buttplate (flat)................................... $8.00
MSR127 Buttplate Screw................................. $1.25
CLN014 Cleaning Rod 12 1/2" M98/43 ............ $5.95
CLN025 Cleaning Rod 15" GEW 98...............$12.50
CLN018
Cleaning Rod 15" VZ24/G24(T).......$13.50
CLN013 Cleaning Rod early 10"....................$12.00
CLN049 Cleaning Rod M93 17 1/4".................$10.00
CLN074 Cleaning Rod Stock Nut.................... $5.00
MSR135 Cocking Piece.................................... $7.00
MSR136 Ejector.............................................. $5.00
MSR138 Extractor.........................................$19.95
MSR516 Extractor new original.....................$26.50
MSR139 Extractor Collar................................. $8.00
MSR140 Firing Pin........................................$19.95
TOOL041 Firing pin protrusion gage, 98 Mauser new
orig military – for 8mm & 7.62mm Mauser.
Also has a firing pin tip diameter gage
.......................................................$24.95
MSR141 Firing Pin Spring............................... $3.75
MSR514 Firing Pin Yugoslav ’98 Mauser........$30.00
MSR143 Floorplate (used)................................ $9.00
MSR142 Floorplate new orig, unnumbered....$19.95
MSR146 Follower (milled)................................ $8.00
50 Hilton Street, Easton PA 18042
www.e-sarcoinc.com /
www.sarcoinc.com
610.250.3960 Fax: 610.250.3961
BACK AGAIN!! NEW PRODUCTION ‘98
MAUSER FIRING PINS
We just produced these out of the best 4140 steel
- The good news is that we redesigned the cocking
piece knotches to fit multiple manufacturing variations of the cocking piece. For years we have suffered pins and cocking pieces that wont fit together
and hours and hours of sorting for fit. Problem
solved + a new 4140 pin. $22.50 MSR431
‘98K MAUSER ACCESSORY KIT
Cleaning rod, Our famous K98 Repro
sling, front sight hood. Value $55.00
Sarco Special $24.95 MSR365
MAUSER RIFLE CLEANING RODS
1. 98K 12.5 inch rod, for most 98K
and G-43 rifles...................$5.95 ea. CLN014
2. 98 K 10 inch, for early 98K
.............................................. $12.00 CLN013
3.G33/40 Rod, Special length rod used only on
the Czech Mountain carbines made by the Germans as the G33/40.............. $14.95 CLN016
4.VZ24 Rod, Correct length and diameter rod for
the Czech VZ24 rifles. Also correct for G24 (T)
rifle........................................ $13.50 CLN018
5. Chamber cleaning tool, wood.....$3.95 CLN084
6. 121⁄2” rod for M98/43 Spanish$12.50 CLN019
7. Cleaning rod M93 171⁄4"...........$10.00 CLN049
8. Cleaning rod – Turkish model 38 Mauser
& M98....................................$11.95 CLN127
9. M95 Mauser Chilean rifle........$13.50 CLN129
10. Argentine M91 & M1909 Mauser....$10.00 CLN024
11. 1916 Spanish short rifle..........$12.50 CLN136
12. Chilean M1935 short rifle........$25.00 CLN131
13. Swedish M1896 rifle.................. $8.00 CLN020
14. Swedish M1938 carbine..........$12.50 CLN021
15. Brazilian M1908 Mauser.........$12.50 CLN026
16. GEW 98 Mauser WWI..............$12.50 CLN025
VERY NICE REPRO OF THE
WWII 98
MAUSER AMMO
POUCH
Nicely done.
Black pebble grain. $9.95 each,
$18.95 per pair, $34.75 for
2 pairs MSR483 Repro 98
MAUSER RIFLE BARRELS
VARIOUS MODELS
1.Kar 88, 8x57, original used, with
good bores. 171⁄2"
.............................$50.00 MSR096
with hand pick bores.......... $75.00
2.K98 Mauser barrel – rough bore
.............................$24.95 MSR424
3.Rare Argentine M1909 Engineers
Carbine barrel – bores vary
.............................$49.95 MSR512
M98 MAUSER BOLTS
Complete bolt assembly with firing pin,
extraction, bolts sleeve, etc. Standard
length ’98 bolt, fits German 98K,
Czech VZ24, Argentine ’09, etc. Gew
98 style bolts. Good, original condition.
$79.95 ea. MSR123
’98 MAUSER ENSEMBLE
WWII sling
2 ammo pouches
Cleaning rod
Late oil bottle
Front sight cover
Proper 8mm brush
$66.00 value – for only............... $44.50 MSR590
PROPER 8x57mm BORE BRUSHES
Bronze brush – 5 for...................... $6.95 CLN124
Stainless steel brush for cleaning those tough
military bores 5 for $8.95 CLN121
MAUSER STOCK MILITARY ISSUE
1.
2.
3.
4.
Israeli K98 handguard only
........................................ $19.95 MSR403
1908 Brazilian long rifle stock good cond.
........................................ $49.95 MSR366
A– Select (very few only) 1908 Brazilian
long rifle stock................ $85.00 MSR366A
1908 Brazilian long rifle stock with handguard, good cond.............. $65.00 MSR375
5. 1908 Brazilian long rifle stock with hanguard,
Select.............................. $100.00 MSR375A
6. Steyer M1912 stock w/buttplate & bayo lug
...............................................$39.95 MSR548
7. Steyer 1912 Rifle Stock, good
condition.................................$49.95 MSR549
Use above 1908 Mauser stocks to rework the 1908’s
with cracked stocks currently on the market.
’98 MAUSER MILLED MILITARY TRIGGER
GUARD ASSEMBLIES
Complete guard with catch floor plate, follower & spring
..................................................................$34.95 MSR208
Stripped trigger guard assy.........................$23.95 MSR206
(see this page for guard screw sets)
98 MAUSER 8x57MM STRIPPER CLIPS
Steel 5rd............................... $2.00 STC013
Original brass few only......... $3.00 STC028
’98 MAUSER FRONT SIGHT
COVERS
Back Again!
New condition $6.50,
3 for $17.95 MSR153
98 MAUSER GUARD SCREW SET
MSR372 – Military set w/lock screws used
...........................................$9.75
MSR373 – Military guard lock screw set new
...........................................$3.50
98 MAUSER COMMERCIAL GUARD SCREW SETS
Commercial set, new........... $6.95 MSR158
Commercial set, used....... $5.00 MSR158A
NEW ’98 MAUSER
SPORTER BARRELS
We got a deal on a few 100 assorted caliber Mauser barrels. 24" Standard taper
sporter barrels 5/8" at muzzle. Made by
the renowned Citadel barrel producer.
Calibers available:
MSR601 .30-06........................... $74.95
MSR351 .300 Win Mag................ $79.95
MSR611 7mm Rem mag.............. $79.95
Note: These barrels were made special
with tight threads for accuracy. They
screw on fine with barrel installation
equipment.
K98 MAUSER COMBO TOOL FOR
TAKING DOWN THE FLOORPLATE &
OILING AND CLEANING THE CHAMBER
These are original and in excellent condition. Hard to find!.............$9.95 MSR550
Check our website for a fabulous assortment of ’98 Mauser
trigger guards over 35 variations – we had a big sort!
See our next page O for
more ’98 Mauser items!
MSR147 Follower (stamped, WWII)................$17.50
MSR148 Follower Spring................................. $4.00
MSR151 Front Sight........................................ $4.00
MSR153 Front Sight Hood, 98K....................... $6.50
MSR155 Front Sight Protector VZ24..............$10.00
MSR157 Guard Screw Bushing....................... $2.00
MSR158
Guard Screw Set (commercial) New
......................................................... $6.95
MSR158(A) Guard Screw Set (commercial) Used.. $5.00
MSR372
Guard Screw Set w/Lock Screws (military)
......................................................... $9.75
MSR159
Handguard, K98 (beechwood, used, orig)
.......................................................$15.00
MSR161 Handguard used walnut K98, orig..$18.95
HNGD34 Handguard 1908 Brazilian long rifle $19.95
MSR579 Israeli 1 leaf bolt stop spring.............. $9.95
MSR162 Low Scope Safety.............................$15.95
MSR129 Lower sling swivel, detachable, 98 WWI GEW
......................................................... $8.50
MSR193 Parade sling loop swivel, original 98 WWI
GEW................................................. $4.00
MSR595 Polish WZ29 ’98 Mauser Floorplate RARE
.......................................................$25.00
MSR415 Combination of MSR129 & MSR193.. $9.95
MSR589 Portuguese 1904 hinged trigger guard,
milled steel – fits 98 Mauser......... $100.00
MSR595 Rare WZ29 Polish 98 Mauser Floorplate
.......................................................$34.95
MSR175 Rear sight & handguard screw VZ24
......................................................... $4.00
MSR180 Rear Sight Sleeve ............................$15.00
MSR185 Safety................................................ $4.25
MSR150 Front Guard Screw (military)............. $4.00
MSR149 Screw, Front (commercial) New..........$3.50
MSR149(A) Screw, Front (commercial) Used
.........................................................$3.00
MSR373 Screw, Guard Lock Set (military) New
.........................................................$3.50
SLNG010 Sling GEW 98 (WWI Style).............. $16.95
MSR193 Sling Loop for GEW Parade Sling position
.........................................................$4.00
MSR196 Stock Set German Wartime Laminated (used) w/
handguard, hardware, & cup buttplate....$N/A
STC013 Stripper Clips (8mm, 5 rd).................$1.45
MSR208 Trigger Guard Assy, milled military
...................................................... $34.95
MSR206 Trigger Guard Assy, stripped
...................................................... $23.95
O2
SARCO, INC.
50 Hilton Street, Easton PA 18042
www.e-sarcoinc.com /
www.sarcoinc.com
610.250.3960 Fax: 610.250.3961
Here’s your chance to create your
own “Enemy AT The Gates” sniper
rifle with our authentic type scope
and turret mount. See our website for a little background on the
Turret Mount
MORE MAUSER PARTS
& ACCESSORIES
E-mail: sarcopa@sarcoinc.com
ZF39 SCOPE FOR GERMAN 98K WWII SNIPER RIFLE
Here you have a faithful reproduction of the ZF39 Scope as used by German Snipers during WWII.
This scope has the proper finish, weight, size and steel tube diameter (26.5mm) to install the low turret
mount and short side rail mount that Germany produced for their Sharp Shooters (Scharfschutzen).
The power scope has bullet drop compensator that runs from 100 to 1,000 meters, with increment
marks every 50 meters and a focus adjustment vane. The three-post reticle and clarity is superb, both
ends are just hand tight in order to remove and install closed rings low turret mounts, if other mount
is going to be used, just tightened by hand all the way. Now you have the chance to get your Mauser
98K or long rifle fitted with the optics and mounts that made the German Sniper System so famous.
Best of all is at a price you can afford !!!
MAUSER 1909 ARGENTINE MUZZLE
PROTECTOR
WWII GERMAN ZF39 SCOPE
AND MOUNT
closed ring low turret
MSR545
Now set as a
package deal. You
canhave a ZF39
K98 Mauser sniper scope with the side
rail mount assembly
............................................. $449.95,
3 for........................ $1249.95 MSR571
Open ring low turret
MSR544
THE ZF41 MOUNT
GERMAN WW2 ZF39 SCOPE MOUNT
Brass muzzle protector fits on over the muzzle and
protects the front sight.Original.. $12.95 MSR024
MAUSER SCOPES & MOUNTS
MSR499 ZF39 Scope 4 power............................... $299.00
MSR573 ZF39 scope 6 power................................ $299.00
MSR401 Short side rail scope mount assembly..... $199.00
MSR545 Low turret scope mount assembly with closed rings
.............................................................. $175.00
MSR544 Low turret scope mount assembly with split rings
.............................................................. $179.00
MSR500 Mauser swept back scope mount............ $149.95
MSR501 Mauser swept back mount with ZF4 scope
.............................................................. $429.00
MSR554 ZF39 scope with closed ring low turret mount –
specify 4 or 6 power............................... $435.95
MSR555 ZF39 scope with split ring low turret mount
Specify 4 or 6 power scope...................... $459.00
MSR571 ZF39 sniper scope with short side rail mount Specify 4 or 6 power............................... $449.00
Please Note: Base screws are not included.
Please Note: The closed rings are standard WWII issue but many
folks want the open rings for ease of installation and the open rings
are acceptable in the national sniper scope matches.
New and accurate manufactured Scope Mount as used by
the Wehrmacht & SS from 1941-1945. Improved last model
mount with the top lock screw,2 pins and extra long locking
lever. Set up with 27mm rings. If you need for a 1” scope, we
can include shims at no charge, but you must ask! Perfect
for creating a WWII German Sniper Rifle..................... $199.00 MSR401
Note: California law forbids sales to
residents of Ca.
ORIGINAL MILITARY ISSUE RIFLE GRENADE
LAUNCHERS FOR MILITARY RIFLES
We have 5 types to choose from. All are in like new to excellent
condition and install and dismount in seconds.
A. Mauser K98 Grenade Launcher, Military production
...................................................................... $49.95 MSR489
B. Enfield #4, New GI............................................$39.95 LE4056
C. Mauser K98 Israeli Grenade Launcher............ $74.95 MSR575
D. FN49 Grenade Launcher with leather case..... $34.95 MISC048
E. FN49 Grenade Launcher with new leather case, new condition
overall...........................................................$49.95 FN49074
D.
K98 RIFLE STOCK DISC
P17 & P14 ENFIELD GOODIES
!! ONCE AGAIN AVAILABLE !!
A small lot of P14 (1914) Enfield Extractors – We thought these were gone forever!
P14004 P14 Extractors original...$39.95
P14002 P14 Bolt complete..........$99.95
U.S.M1917 & BRITISH P-14 ENFIELD PARTS
Almost all parts are new G.I.
P14003 P14, Bolt Stripped........................... $32.00
P14002 P14 Bolt, complete.......................... $99.95
P14004 P14 Extractor, original..................... $39.95
P17082 P14 Firing pin spring.......................... $4.95
P14007 P14, Floorplate................................... $9.00
P14009 P14, Follower, Milled.......................... $8.00
P14008 P14, Magazine Box.......................... $11.50
P14010 P14, Speed Lock.............................. $40.00
P14013 P14, Stock and handguards with grenade
launcher sight plate—4 only...$195.00 ea.
P14005 P14, Striker (Firing Pin)................... $20.00
P14006 P14, Triggerguard............................ $15.00
P17016 Bolt Complete.................................. $75.00
P17017 Bolt, stripped.................................. $37.50
P17068 Bolt stop assy, 4 parts w/o ejector... $15.00
P17041 Buttplate Assembly......................... $14.95
P17040 Buttplate Screw Large........................ $3.50
P17056 Buttplate Swivel Screw....................... $4.00
P17012 Ejector, original............................... $16.50
P17043 Extractor......................................... $24.50
P17034 Front guard screw.............................. $3.50
P17 CRITICAL PARTS KIT
Firing pin, Extractor, Bolt, Safety, Ejector, Sear,
Mainspring, Follower Spring
All new parts. Value $93.50
Sarco Special $43.95 P17069
U.S. 1917 ENFIELD CUSTOM COCK
ON OPENING & SPEED LOCK ASSY
Has a modified cocking piece & hi speed lock spring –
mounted on a new firing pin.............$39.95 P17051
Also available for P14.......................$40.00 P14010
P17036 Floorplate ....................................... $10.00
P17038 Follower Spring.................................. $5.00
P17039 Follower, Milled............................... $12.00
P17006 Handguard Ring.............................. $10.00
P17082 High speed firing pin spring................ $4.95
P17054 Lower Band Asembly....................... $10.00
P17083 Lower Band new, original................ $15.00
P17037 Magazine Box..................................... $9.95
P17035 Rear Guard Screw.............................. $3.50
P17004 Stacking Swivel.................................. $9.50
P17052 Stacking Swivel Screw........................ $4.00
P17018 Striker (Firing Pin)........................... $18.00
P17031 Triggerguard................................... $20.00
P17053 Upper Band........................................ $9.50
P17046 Rear handguard walnut new G.I...... $35.00
P17047 Rear handguard walnut used G.I..... $25.00
P17062 Rear handguard hardwood, new G.I..$25.00
P17063 Rear handguard hardwood, used G.I.$20.00
P17044 Front handguard walnut new G.I..... $22.00
P17045 Front handguard walnut used G.I... $18.00
P17061 Front handguard hardwood, new G.I.$17.00
P17060 Front handguard hardwood used G.I.$15.00
See our website for all other P17 & P14 parts
SPECIAL! JUST IN THE DOOR
High speed P17 or P14 Enfield firing pin spring.
Speed up your lock time same as used on our
speed lock assembly....................... $4.95 P17082
P17 SPORTER STOCKS – Beautiful hardwood stocks
used for ‘sporterizing’ the Enfield P17 Rifle. These
hardwood stocks feature checkering on the forend
and grip, and have buttplate, grip cap, cross stock
bolt, Monte Carlo rest and a medium satin stain.
These stocks have blemishes from storage including
one or several nicks, cracks, chips. All blemishes
are repairable and we have chosen to let some go
because our repair shop is already working overtime!
This is a ‘win win’ for those who don’t mind a little work to make the repairs. Sold as-is and no returns.
At this price, we think you will be very happy with the quality! $20.00 ea. P17084 (compare at $85.
elsewhere!)
PLEASE NOTE: Please, do not send us your original parts for comparison.
We are not responsible for lost, damaged, or misplaced parts in transit or
upon receipt. Please include only a picture and dimensions of parts needed
for comparison. Thank you.
DISCLAIMER: Parts sold by Sarco should be installed only by a competent gunsmith. These products are sold as is and without a warranty. No liability is expressed or implied for damage or
injury which may result from the improper installation or use of these products.
REGARDING LOCAL, CITY & STATE REGULATIONS!
SARCO makes a large effort to keep abreast of state & local gun laws. With over 20,000 laws on the
books this is a Herculean and impossible job. Some of the products sold by SARCO could be restricted for
sale in your local area, while not restricted nationally. This could include, but not be limited to firearms,
ammo, parts, high cap mags, edged weapons, air guns, etc. You must determine your right to purchase,
own, use or resell specific products offered by SARCO in your jurisdiction. As local laws are constantly
changing, it your responsibility to determine if a product is prohibited before ordering from SARCO. You
warrant by ordering from SARCO that you are a legal adult without any legal restrictions from ordering
and are complying with all state, local, and federal laws. Please check your local laws before ordering.
LEGAL ADVICE????? PLEASE, DO NOT CALL SARCO for legal advice on guns. We are not a legal
firm and therefore are not able to give any advice. Any discussions had with any SARCO employee are
to be considered as guidance only. For questions on legal gun matters we suggest you call ATF. That’s
what we do.
Was made by Berlin-Lübecker Maschinenfabrik, a German WWII firearms manufacturer,
the company made all the ZF-41 Marksman
scope mounts from 1941 till 1944.
Another added feature is that you can install
it yourself without the need for drilling and
tapping and that was something the German
Army had in mind, they could send the
mount and scope to the field and with a small
punch and a brass hammer, the scope was
installed in minutes, thus making a standard
98K into a Sniper System.
You will ask yourself, how come I did not buy
it sooner?
ZF41 Scope....................... $289.00 MSR473
ZF41 Scope Mount............ $189.00 MSR474
ZF41 Scope & Mount........ $469.00 MSR476
Exact repro of the original ZF41 Scope can
cover with cleaning bursh, sunshade retainer
& canvas belt strap........... $200.00 MSR475
C.
B.
A.
Usually inserted in the right
side of Mauser stocks in the
1930s and in Garrison rifles
of the Home Guard through
the early war years. Would
ID mfg., date, serial #
...................................$4.95 MSR596
ATTENTION – EASTON SHOWROOM CUSTOMERS
Re: In Stock Inventory - We try and maintain stock of most items in our Easton, PA showroom,
however with the vast array of material we carry, this is not always possible. If you are planning
on visiting the showroom, please feel free to call ahead to make sure that we stock the item(s) that
you need. If these parts are not at the showroom, we will arrange to have them brought in from our
warehouse for you to purchase or look at. Please give us a least a few days’ notice before your visit
so we have time to bring the goods in. Please note that the prices in Shotgun News are dealer prices
and may not be the same prices as in our showroom. We are striving to make your shopping experience with us a pleasant and hassle free as possible.
ORDERING INSTRUCTIONS
~ There are different procedures for
Ordering PARTS vs Ordering FIREARMS ~
PHONE ORDER – Call (610) 250-3960
ONLINE ORDER – Go to www.sarcoinc.com
FAX ORDER – (610) 250-3961
MAIL ORDER – Sarco Inc, 50 Hilton St, Easton
PA 18042
SHOWROOM VISIT – Mon-Sat 10am-5pm /
Friday Opened til 8pm
For directions to the showroom, see website.
CUSTOMER SERVICE – info@sarcoinc.com
PARTS QUESTIONS: parts@sarcoinc.com,
MACHINE GUN QUESTIONS: mgdave@sarcoinc.com
ABOUT HIGH CAPACITY MAGAZINES:
Although we try to stay abreast of current
State gun laws, it is a herculean task
with over 20,000 laws on the books. By
ordering, you are stating that you are
complying with your Local & State laws.
Most States allow large capacity magazines. Some do not. If you are unsure on
this issue, contact your Local or State law
enforcement to confirm what is allowed.
This is a partial list of States with some
hi-capacity restrictions: NJ, NY, MA, MD,
HI, KS, CO, CT, IL and various county
laws therein including Chicago, D.C.
Prices are subject to change without notice. We are not responsible for
typographical errors or misprints
MAGAZINE SALES IN CONNECTICUT
Until we get further clarification we can ship
NO cartridge magazines, feeding devices, or
drums to Connecticut. We are able to send 10
round or under magazines to holders of FFL.
OUR INVENTORY
· We try to ship the best condition parts at the
time of your order. Some are new and some
are used, many hard to get.
· Prices are subject to change without notice.
Our ads in the Shotgun News are catalogue
prices and may not reflect any sales or higher
pricing found on our website.
· All sales subject to availability. Acceptance
or receipt of order does not constitute confirmation of order. Employees are not authorized
to modify prices or conditions stated in ads.
· All NFA rules apply.
Sarco only sells products to persons 18
years or older
Please note: Sarco’s responsibility for goods
shipped ends when it leaves our door. Lost or
damaged claims are the responsibility of the claims
carrier. We will assist in every way for you on
claims to carriers.
RETURNS
We offer a 5-day inspection period on all of
our merchandise, except for special order
items which are not refundable. Items that
state they are sold “as-is” are not returnable. Tools and marketing devices are not
returnable.
· PHONE ORDERS, EMAILED, FAXED OR MAILED-IN
ORDERS: You will need a Return Authorization Number to return something. Please
email returns@sarcoinc.com or call (610)
250-3960 ext.114
for a RT #. Feel free to check on the status of
your return, credit or refund.
· ONLINE ORDERS: Please visit our website
www.e-sarcoinc.com and click the Return
Policy link. Fill out the printable form and
mail it back with your package. Feel free to
email our e-Comm department at ecomm@
sarcoinc.com to check on the status of your
return or call (610) 250-3960 and ask to be
transferred to the e-Commerce Department.
We do not refund any shipping cost unless
the error/problem causing the return is our
fault.
Returns may be subject to a 10% restocking
charge.
SUPER RARE SWEPT BACK MOUNT
FOR K98 MAUSER SNIPER RIFLE
Quality reproduction of
this incredibly rare sniper
scope mount. It takes
the ZF-4 scope, which we
have available. Mount is
complete with the rings.
These mounts were made to standardize the
ZF-4 scope at the very end of WWII. This
is the rarest of the rare. It comes complete
with the mounting base & rings & screws for
attachment to a standard 98K WWII Mauser.
Developed by Sauer. $179.95 MSR500
Combo Special – Swept back mount with ZF4
scope $469.95 MSR501
SPECIAL OF THE MONTH
MSR500 - $149.95, MSR501 - $429.95
GERMAN K98 MAUSER REAR SIGHT
COVER
In 1941 & 42,
Mauser K98 leather
rear sight covers
were issued for
mountain troops
and also were found
amongst those designated with sniper duty.
Rarely seen although some were liberated out
of the Balkans in the 1990s. Cover w/ WW2
German markings............... $15.95 MSR617
MISC. 98 MAUSER ITEMS
1. Rare brass Turkish Mauser cleaning
funnel – locks on to muzzle. To pour
solvent down the bore – for Turk M1890
& M1893 ................................. $14.95 MSR300
2. Original Argentine SOM sniper scope w/base &
leather case..................................... $3495.00
3. Rare M98/43 La Coruna Spanish
muzzle cover................................$9.95 MSR217
4. M98/43 Handguards, replace your
cracked one.............................. $16.50 MSR216
5. VZ24 Mauser new original stock disc....... $4.95
3 for.........................................$12.50 MSR523
6. Original Israeli K98 grenade launcher, like new
.............................................. $49.95 MSR575
7. Orig Yugoslav, 98 & M48 etc Mauser oiler
................................................ $4.95 MSR576
8. Rare original 1904 Portuguese Verguiero front
sight cover, new........................ $9.95 MSR591
FOUND SOME WHATCHAJIGAMAROOS IN
THE WAREHOUSE!
These bolts are straight out
of the FN Belgian factory
years ago. This is a complete back end – threaded
for sleeve on the inside. For
a K98, here are a couple ideas:
1. Use this rear with the front of a normal bolt
to build a long or short Mauser action of your
dreams.
2. Use the bolt handle to weld a true FN pattern
original low scope bolt for your sporter project.
3. Use for that pet project you created when you
woke up with a startle at 3am
$4.95, 3 for $11.95 MSR615
Note – We have two or three thousands of these
if your brainstorm is marketable. Talk to Dave
or Cholly.
SHIPPING
ALL ORDERS WILL BE RECEIVED,
PROCESSED AND SHIPPED OUT OF OUR
PENNSYLVANIA LOCATION.
MINIMUM SHIPPING AND HANDLING
CHARGES START AT: $9.50
Rifle Stocks and Barrels…. $12.50
Call for larger items on prepaid orders
* NJ residents please add 7% sales tax. Not
all items available to NJ residents.
* PA residence please add 6% sales tax
All orders to Alaska and Hawaii shipped
via US Mail, unless customer specifically
requests Blue or Red Label UPS (not available
for online orders). Employees not authorized
to modify prices or conditions stated in this
advertisement.
OUR GUARANTEE
Our guarantee is simple and easy to understand. If you are not satisfied with any
item received from us you have 5 days to
return it for a replacement or a refund of
the advertised price. All returns must be
accompanied by a letter WITH YOUR INVOICE NUMBER and explanation of the
problem. All returns must be in the same
condition as you received them-any alterations or work will void the guarantee.
Special order items not returnable. We
can not accept returns on TOOLS unless
the tool is defective. We do not refund any
shipping costs unless the error/problem
causing the return is our fault. Returns
may be subject to 10% restocking charge.
Send all shipments pre-paid. CODs will
be refused. Any items returned due to
customer’s error are subject to a 10%
restocking charge. ($2.00 minimum). As
we do not install the parts we sell, we
cannot guarantee they will function when
installed by others. For proper function
and safety, many gun parts should be
installed by a competent gunsmith - see
our disclaimer:
X2
SARCO, INC.
Phones Open: Mon Fri, 8:30am – 5:00pm
Showroom Open:
Monday - Saturday,
10:00am – 5:00pm,
Friday til 8:00pm
50 Hilton Street, Easton PA 18042
www.e-sarcoinc.com /
www.sarcoinc.com
610.250.3960 Fax: 610.250.3961
E-mail: sarcopa@sarcoinc.com
MAS 36 FRENCH
Complete bolt............. $89.95
Firing pin & spring..... $17.95
Bolt plug........................ $6.00
Extractor.................... $10.00
M36056
M36066
M36023
M36018
Set #2 A
ction parts: All bolt parts
above, plus floorplate, follower
& spring, rear sight aperture,
trigger & sear assy
..................... $29.95 M36049
Set #3 Wood Set: All 3 pieces in excellent to like new
..................... $65.00 M36050
Set #4 C
ombo Set: Sets #2 and #3
..................... $90.00 M36051
MAS 36/51 GRENADE
LAUNCHER RIFLE PARTS
A. Stock Set – 3 pieces in VG to exc
condition.................... $75.00 M36045
B. Grenade Launcher Assembly –
compete “front end” of a MAS 36/51.
Launcher sleeve, sight,
upper band, range slide. Sleeve has
slight saw cut............. $49.95 M36046
C. Set A & B combo.... $99.95 M36047
See our website for all
MAS 36 & 36/51 parts
COMPLETE SET OF FRENCH
MAS 36 RIFLE PARTS
less barrel and receiver.
VG cond or better $99.50
FRENCH MAS 36 ACCESSORIES
1.Field Manual (original French)...............................$4.95 SB018
2.Leather sling.........................................................$15.95 M36032
3.MAS36/51 Complete Stock & HG set
with all hardware....................................... $125.00 M36058A
4.MAS36 full stock set w/all metal......................$85.00 M36057
5.Orig broken shell extractor.................................. $9.95 BSE005
6.Original grenade launching boot..................... $19.95 M36034
7. Pull-through bore wiper.....................................$1.95 M36053
FRENCH MAS-36/51 RIFLE PARTS SET
Industry forged prior to WW2, used by Vichy forces against U.S.
GIs in North Africa, and extensively brandished in Indochina
and the Algerian conflict as well as Cambodian and Syrian
Civil Wars. We were able to obtain these rifles with barrels and
receivers removed. These are the model with grenade launcher
and sight assy. Comes with all parts
shown including wood stock & handguard in very good condition.
...........................$150 .00 M36067
ALLIED & AXIS DISPLAY GUNS (NON-FIRING)
Sarco presents an increasing new line of finely made metal and wood replica firearms, noted for their
historical significance in the battle for and against, the rise of fascism and geo political domination in the
World Wars of the last century. These display guns are full size and the best quality on the market. Many
of them come with markings and or accessories not available from the competition. These are perfect for
presentation, static display, reenacting, or for outfitting that military vehicle in the garage!
NOTE ON NON-FIRING DISPLAY GUNS
While most Americans can own non-firing display guns, some States and municipalities have enacted
regulations inhibiting ownership. It is important that you check your State’s gun laws to see if you reside
in one of these areas. We cannot ship our display guns out of the country. Below is a partial list of States
where there are laws concerning ownership of display guns. Remember, by ordering from Sarco, Inc.,
you are confirming to us that you are complying with your State regulations on this issue. CA, CT, KS,
MA, MN, WI *All non-firing display guns come with an orange plug inserted in the muzzle – required by
Commerce law.
STEN MK-2 SMG DISPLAY GUN
Outstanding new arrival of a non-firing, all metal
replica of the venerable Sten Gun used since WWII.
Stock is removable, bolt can be charged, and magazine is removable. We have two
versions in stock:
A. STEN MK2 WITH SLING .& MAGAZINE
................$145.00 REP22
B. STEN MK2 WITH SLING, .MAGAZINE AND
COMMANDO PISTOL GRIP FOR
CONVERTING THE GUN INTO A PARA
TROOP VERSION.................$159.95 REP23
AK 47 PARTS KIT ‘BREAKTHROUGH’!
.....In both PRICE & CONDITION....
These are the FEG Mfg., Hungarian
AK63D under folding stock gun kits
disas­sembled and packaged nicely. Bolts
EVEN
LOWER
& carriers have matching numbers.
PRICES!
Hungarian AK quality is re­nowned and
we felt compelled to purchase 1,000 kits
as a value loaded deal which we are passing onto you at a savings! The parts come
from VG to excellent 7.62x39 guns with barrel & part of the receiver removed. These
parts work with standard AK barrels, stamped receivers & internals, and come with
wood pistol grip and hand guard. As an added value we have included the original cleaning kit, muzzle cap, sling, oil bottle & blank
firing device. Super low price! AK63D kit w/accessories. $224.50, 3 for $649.95 AK045 Prices on AK kits have sky rocketed in
the past months and here in is your chance to “beat the market!!” We have a few super select AK kits for............... $249.50 AK049
RECEIVER & BARREL SUBCOMPONENTS INCLUDED:
Barrel Parts
Front sight Hand guard cap
Gas block Rear sight base
NO BARREL PIN
Receiver
Trunion
Trigger guard support
U.S. M1 CARBINE (NON-FIRING)
Very realistic looking with some
functioning parts. This version is
the standard WW2 model w/o bayonet lug
$218.95 REP07
GERMAN P38 PISTOL (NON-FIRING)
Issued to Wehrmacht troops in 1940, this pistol became
the regular sidearm of 3rd Reich Officers & some NCOs.
NEW!
Cheaper to produce than the Luger, it was light and effecITEM
tive. Even a half pound lighter than the Model 1911 and
with an 8 rd. magazine. Our authentic looking non firing
display gun looks and feels like the real thing. Slide can be cocked, hammer
pulled and trigger squeezed with a distinctive click. A classic display piece in metal
with black plastic grips like the original. We have two offers: 1. P38 non firing pistol
$72.95 REP05
2. P38 pistol with our WW2 dated hard shell holster $87.95 REP15
STOCKS AND FORENDS ... SARCO’s GOT A BOATLOAD OF
WOODEN STOCKS & FORENDS...Super Commercial Stock
Deal.... all brand new original stocks and forends!
Seriously, a great deal on wood for
firearms under the mfg names such as
Mossberg, Marlin, H&R, Savage, Ithaca,
S&W, and Winchester. 15 different stock
and forends at a fraction of the cost and
WOW! THIS IS
with no duplicates. Total Value $587.00,
75% OFF!
but Sarco’s Special Price is all 15 pcs.
for $150.00 or buy 2 LOTS for $265.00! This is the best deal we have offered in a long time.
I would have bought it myself 30 years ago when we were building our commercial gun
parts business. This is a great opportunity for Gun Show sale items and if you sell 3 of the
15 items, you’re out of it! ONE LOT of stocks & forends
.................................................................... $150.00, TWO LOTS for $265.00 STK363
WE NOW HAVE A NEW SHIPMENT OF
NEW MFG AK47 BARRELS, ONLY $79.95!
WHILE THEY LAST! AK047
FRENCH MAS 49/56 RIFLE PARTS
BRITISH WEBLEY .38
REVOLVER MK4
Bolt carrier.............................................$95.00 M4906
Bolt, stripped.......................................... $75.00 M4907
Bolt, complete..................................... $100.00 M4910
Dust cover w/rear sight....................... $125.00 M4904
Extractor & spring..................................$25.00 M4905
Firing pin................................................$25.00 M4903
Gas tube.................................................$25.00 M4908
Grenade Launcher spring......................... $5.00 M4909
Recoil spring ............................................ $9.95 M4901
(NON-FIRING)
Standard service revolver of the British
Military in WWII Sold with lanyard.
Webley Pistol .38 Pistol w/lanyard
$75.00 REP17
FRENCH MAS 49/56 SURVIVAL KIT
Webley Pistol .38
Pistol w/lanyard
& leather holster
$105.00
REP04
Original parts and accessories to keep the rifle purring!
An $80.00 Value at a discount! Includes: Extractor, Firing Pin, Gas Tube, screwdriver, brush, grenade launcher
retaining spring, canvas pouch
..............................................................$44.95 M4902
NEW!
ITEM
M1 GARAND RIFLE (NON-FIRING)
The wood on this rifle is better looking
than most govt. wood stocks. Wellmade w/some functioning parts…$235.00 REP08
U.S. THOMPSON 1928 SMG
W/20 RD. MAG. (NON-FIRING)
Some functional parts, includes sling and 20 rd.
stick magazine…$242.95 REP13
GERMAN WW2 MP44 ASSAULT RIFLE
(NON-FIRING)
Full size, solidly built with some
functioning parts.Comes with magazine. Feels and
looks like the real thing! $240.00 REP03
U.S. M1A1 PARATROOP CARBINE
(NON-FIRING)
A.
B.
Rear stock mount
Trigger & mag catch
support
Very accurate folding stock version of the
Paratroop M1A1 carbine. Some functional
parts and magazine. $220.95 REP11
GERMAN MP-40 SMG
(non-firing)
Famous full size display gun with operating bolt, recoil assembly,
folding stock, mag catch and trigger. Saw combat throughout
Europe, Africa, and even Vietnam! Bound to spark interest and
conversations from all who see it. Realistic metal and plastic
construction and it comes with steel magazine and leather sling.....$210.00 REP02
THOMPSON 1928 DISPLAY GUN (non-firing)
Wood and metal replica of the
venerable submachine gun that
made history with gangsters of the 20s, and
our troops and allies in WW2. Well made and
has a cocking mechanism that moves back and
forth and trigger that allows the bolt forward.
Magazine catch also works. Comes with steel 50rd. display
drum. A real crowd pleaser and guaranteed to start conversations!
........................................................................................................$249.95 REP01
DISPLAY PISTOLS (NON-FIRING)
U.S. MODEL 1911
Full sized metal reproduction with diamond knurled wood grips.
Sold with lanyard. Model 1911 Pistol w/lanyard…
1. Model 1911 Pistol w/lanyard ............................. $135.95 REP12
2. M
odel 1911 Pistol Pistol/lanyard & Hip Holster
........................................................................... $147.95 REP16
STANDARD SPORTING RIFLE
SIGHT
This is a basic item for
any gunsmith or tinkerer to have. This
handy sight is as close to a universal rifle
sight as you can find. Can be used on
.22 rifles or high power sporters. Slips
onto dovetail on the barrel. Adjustable
for elevation with sliding elevator. There
is no limit to the uses that you’ll find for
this handy sight.................... $4.95 ea.
10 for..........................$39.95 SGHT04
CLASSIC STREAMLINED FRONT
SPORTER RAMP SIGHT
with blade and front sight.
• Serrated & contoured
ramp
• Screw on attachment
• Contoured front end
• Gold bead front sight
List Price $40.52!! Sarco Special
$9.95 SGHT007 5 for $48.00 10 for
$78.95
GERMAN LUGER PISTOLS
(3 VARIETIES)
Beautifully made, full size
replicas in metal with knurled
wood grips. Very realistic looking. We offer a couple with and
without holsters:
1. S
tandard luger w/ 4" barrel
$112.95 REP06
Standard luger w/ WWI canvas holster
............................................... $122.95
2. N
aval Luger w/ 5" barrel.......... $112.95
Naval Luger w/ WWI canvas holster
............................................... $122.95
3. A
rtillery luger w/ 8" barrel....... $124.95
REP14
REP09
REP18
REP10
PPK PISTOL (NON - FIRING )
Another of
our well-made
metal replicas
of the stalwart
sidearm of the
Wehrmacht, 007,
and many other
good guys and
arch villains! Full
size metal replica
with moving slide and hammer/trigger
click..................................$84.95 REP21
GERMAN MAUSER C96 PISTOL
Full size non
firing display
gun manufactured in metal
with wood
grips. This
replica is very
well made and
features a cocking mechanism that moves
and trigger that clicks when cocked. Also
comes with a lanyard. A terrific example of
the Mauser pistol that served throughout
the world in military circles including
limited numbers used by U.S. officers in
the Philippines................... $89.95 REP24
ISRAELI SNIPER AMMO POUCH
Khaki canvas pouch used by
Snipers for holding 8 rds. of
.308 Match ammo which can
be pulled out in an instant Pouch
Only.
like a machine gun belt.
Has U.S. belt hooks too!
First time available
NEW!
$25.00 MISC349
ITEM
CLASSIC MARBLE/WILLIAMS STYLE FULLY
ADJUSTABLE REAR SPORTING SIGHTS
• Screw on attachment
• Dovetailed graduated windage &
elevation adjustment
• Elev. & windage lock w/set screws • Extremely high quality
• Works perfectly with wide range of front sights
SARCO SPECIAL $13.50, 5 for $60.00,
10 for $110.00 SGHT08 Retail Value $27.00