2383 General Directions e

Transcription

2383 General Directions e
English
1/3
Web Site
U.S. & Canada Toll-Free
http://www.simplicity.com
1-888-588-2700
The Pattern
5
6
7
SYMBOLS
GRAIN LINE Place on
straight grain of fabric
parallel to selvage
ADJUST IF NEEDED
Make adjustments before placing
pattern on fabric.
TO LENGTHEN:
Cut pattern
between
lengthen or
shorten lines.
Spread pattern
evenly, the
amount needed
and tape to
paper.
PLACE SOLID LINE on
fold of fabric.
CENTER FRONT OR
BACK of garment.
13
8
NOTCHES
9
B
DOTS
CUTTING LINE
12
14
C
D
C
B
11
15
E
A
10
1-FRONT AND BACK -A,B,C,D
9-FACE AND EARS APPLIQUE -C
2-BAND -A,B,C,D
10-HEAD APPLIQUE -D
3-TRIM -A,D
11-MUZZLE APPLIQUE -D
4-BODY APPLIQUE -A
12-HAT TOP -E
5-HEAD APPLIQUE -A
13-HAT CROWN -E
6-BODY APPLIQUE -B
14-HAT TRIM -E
7-WINGS APPLIQUE -B
15-HAT BRIM -E
LENGTHEN OR
SHORTEN LINES
SEAM ALLOWANCE: 5/8" (1.5cm)
unless otherwise stated is included but
not printed on MULTI-SIZE PATTERNS.
Mark your size with colored felt tip pen.
See chart on tissue for how to use MULTISIZE PATTERNS.
pattern printed
side down
pattern printed
side up
★
✻
SEW garment following Sewing Directions.
PIN or machine-baste seams matching notches.
STITCH 5/8" (1.5 cm) seams unless otherwise stated.
PRESS seams open unless otherwise indicated clipping when necessary so
seams will lie flat.
• TRIM seams to reduce bulk, as shown below.
•
•
•
•
selvages indicating
direction of nap or
design. Fold fabric
crosswise with
RIGHT sides
together, and cut
along fold (a).
a.
SELVAGE
Turn one fabric
layer around so
arrows on both
layers go in the
same direction.
Place RIGHT sides
together (b).
SELVAGES
SELVAGE
b.
SELVAGES
SEL.
44" 45" (115CM)
WITH NAP
D- CUT ONE OF PIECES 10 11 EACH OF FABRIC AND
PAPER BACKED FUSING WEB REMNANTS
1
SEL.
14
SEL.
SEL.
E HAT TOP AND CROWN
1
FOLD
SELVAGE
USE PIECES 12 13
12
44" 45" (115CM)
FOLD
WITH NAP
INTERFACING
ALL SIZES
2
SEL.
USE PIECES 12 13 15
13
2
FOLD
20" TO 25" (51CM TO 64CM) FUSIBLE
FOLD
ALL SIZES
USE PIECES 12 13 15
FOLD
15
FOLD
CUT ONE OF PIECE 12
USE PIECE 3
3
44" 45" (115CM)
SELS.
WITH NAP
3
ALL SIZES
44" 45" (115CM)
12
SELS.
WITH NAP
ALL SIZES
15
13 FOLD
FOLD
© Copyright 2010—Simplicity Pattern Co., Inc. / Printed in U.S.A. / Simplicity is a registered trademark of Simplicity Pattern Co., Inc.
SELS. 12
15
15
13 SELS.
CROSSWISE FOLD
SELS.
CONTRAST LINING AND BRIM
A,D CONTRAST TRIM
Notch outer
curves
Open out
fabric to single
thickness. Cut
extending
piece on
RIGHT side of
fabric in
position
shown.
Mark small
✻
arrows along both
ALL SIZES
FOLD
44" 45" (115CM)
ALL SIZES
Clip inner
curves
★
If layout
shows a piece
extending past
fold, cut out all
pieces except
piece that
extends.
CONTRAST TRIM
C- CUT ONE OF PIECES 8 9 EACH OF FABRIC AND
PAPER BACKED FUSING WEB REMNANTS
FOLD
WITH NAP
Trim corners
SPECIAL CUTTING NOTES
USE PIECE 14
ALL SIZES
USE PIECE 2
• FOR PILE, SHADED OR ONE WAY
DESIGN FABRICS: Use “with nap”
layouts
B- CUT ONE OF PIECES 6 7 EACH OF FABRIC AND
PAPER BACKED FUSING WEB REMNANTS
44" 45" (115CM)
CONTRAST BAND
• Pin mark dots.
• FOR SINGLE THICKNESS: Place
fabric RIGHT side up.
When lengthen or shorten lines are
not given, make adjustments at
lower edge of pattern.
A- CUT ONE OF PIECES 4 5 EACH OF FABRIC AND
PAPER BACKED FUSING WEB REMNANTS
A,B,C,D DRESS
WITH NAP
• FOR DOUBLE THICKNESS: Fold
fabric with RIGHT sides together.
• Snip edge of fabric to mark
notches, ends of fold lines and
center lines.
A,B,C,D APPLIQUES
See
SPECIAL
CUTTING
NOTES
POSITION OF PATTERN PIECES MAY VARY SLIGHTLY ACCORDING
TO YOUR PATTERN SIZE
USE PIECE 1
To Quick Mark:
PIN pattern to fabric as shown in Cutting
Layouts.
8-HEAD APPLIQUE -C
D
AFTER CUTTING:
Transfer markings to WRONG side
of fabric before removing pattern.
Use pin and chalk method or
dressmaker’s tracing paper and
wheel.
CIRCLE your cutting layout.
Sewing
Trim enclosed
seams into layers
Cutting
Layouts
TO SHORTEN:
At lengthen or
shorten lines,
make an even
pleat taking up
amount needed.
Tape in place.
BEFORE CUTTING:
PRESS pattern pieces with a warm dry
iron. PRE-SHRINK fabric by pre-washing
washables or steam-pressing nonwashables.
SELVAGE
3
4
Cutting/Marking
CROSSWISE FOLD
2
E
info@simplicity.com
✁
Thank you for purchasing this Simplicity pattern.
We have made every effort to provide you with a high quality product.
A
E-mail
General Directions
15 pieces given
1
e
CROSSWISE FOLD
2383
®
English
2383
Sewing Directions
2/3
FABRIC
KEY
BEE APPLIQUE VIEW B
Prepare head and wings appliques. SEE GENERAL
DIRECTIONS FOR PREPARING APPLIQUES
4
RIGHT SIDE
WRONG SIDE
INTERFACING
LINING
4. Center baby rick-rack over solid lines on body, turning ends to
WRONG side. Stitch along center of trim.
Read General Directions on page 1 before you begin.
5
GENERAL DIRECTIONS FOR
APPLIQUES
5. Cut two pieces of grosgrain ribbon each 2" (5cm) long. Fold
ribbon in half, having raw ends even. Pin ends of ribbon 1/4"
(6mm) under body applique at small dots.
Lap side edges of body along inner edge of wings, matching
broken lines. Pin. Baste close to raw edges.
PREPARING APPLIQUES
A. Apply paper backed fusing web remnant to WRONG side
of applique fabric remnant, following manufacturer’s
directions.
Cut applique tissue block along outer solid line. Pin pattern to
RIGHT side of prepared fabric remnant. Cut out each
applique from prepared fabric. Transfer markings to RIGHT
side of applique using a washable fabric marking pen or
pencil.
A
6
APPLYING APPLIQUES
B. Pin appliques to garment as instructed in Sewing
Directions. Be sure to clear all seam allowances. A glue stick
can be used to temporarily hold the appliques in place before
stitching. Fuse appliques in place, following manufacturer’s
directions. Stitch close to raw edges or if you prefer, zig-zag
(satin) stitch along raw edges.
B
A
MONKEY APPLIQUE VIEW C
Prepare head, face and ear appliques. SEE GENERAL
DIRECTIONS FOR PREPARING APPLIQUES
7. Center face applique over head along broken lines. Pin ends
of ear applique under head along broken lines. Center
applique over small dot on front. SEE GENERAL
DIRECTIONS FOR APPLYING APPLIQUES
Stitch close to outer edges of face and head. Stitch again
along first stitching. Stitch two rows along solid line for mouth
in same manner. Work FRENCH KNOT at small dots for
eyes.
Cut a piece of 3/8" (1cm) wide grosgrain ribbon 13”
(33cm) long. Tie in a bow and tack to head as shown on
front of envelope.
7
FRENCH KNOT- For French knot, work with as many threads
as desired and use a large eyed needle. Bring thread to
RIGHT side at A; hold thread with thumb and forefinger in left
hand; wind thread around the needle two or three times. Still
holding thread firmly, slide on needle so that point of needle
may be inserted very close to A, but not in the same hole.
Pull needle to WRONG side, drawing up thread to form
French Knot.
FRENCH KNOT
6. Center applique over small dot on front. SEE GENERAL
DIRECTIONS FOR APPLYING APPLIQUES
Stitch close to outer edges of body and wings Stitch again
along first stitching. Stitch two rows along solid line for mouth
in same manner. Work FRENCH KNOT at small dots for
eyes.
DRESS A, B, C, D
2
1
BEAR APPLIQUE VIEW D
LADYBUG APPLIQUE VIEW A
8
Prepare head and body appliques. SEE GENERAL
DIRECTIONS FOR APPLIQUES
1. Pin WRONG side of head applique over RIGHT side of body
applique, placing straight edge of head along broken lines, as
shown. Stitch close to raw edges.
3
2. Cut eight pieces of grosgrain ribbon each 2" (5cm) long. Fold
ribbon in half, having raw ends even. Pin ends of ribbon 1/4"
(6mm) under applique at small dots. Baste close to raw edge.
9
Prepare head and muzzle appliques. SEE GENERAL
DIRECTIONS FOR PREPARING APPLIQUES
8. Center muzzle applique over head along broken lines. Center
applique over small dot on front. SEE GENERAL
DIRECTIONS FOR APPLYING APPLIQUES
Stitch close to outer edges of muzzle and head. Stitch again
along first stitching. Stitch two rows along solid line for mouth
in same manner. Work FRENCH KNOT at small dots for eyes
and nose.
Cut a piece of 3/8" (1cm) wide grosgrain ribbon 13”
(33cm) long. Tie in a bow and tack to head as shown on
front of envelope.
TRIM VIEWS A, D
3. Center applique over small dot on front. SEE GENERAL
DIRECTIONS FOR PREPARING APPLIQUES. Stitch close
to outer edges and again over first stitching. Stitch two rows
of machine-stitching along solid line for mouth. Work
FRENCH KNOT at small dots for eyes.
9. Press under 3/8" (1cm) on unnotched edge of trim. Pin
WRONG side of trim over RIGHT side of band matching
centers, having raw edges even. Baste raw edges. Stitch
close to pressed edge.
10
CONTINUE AS FOLLOWS FOR ALL VIEWS
10. With RIGHT sides together, stitch front to band matching
centers. Stitch back to band in same manner.
© Copyright 2010—Simplicity Pattern Co., Inc. / Printed in U.S.A. / Simplicity is a registered trademark of Simplicity Pattern Co., Inc.
English
2383
HAT E
3/3
1
11
NOTE: Stitch in 3/8" (1cm) seams unless otherwise indicated.
1. Apply fusible interfacing to WRONG side of hat top, crown,
brim and corresponding contrast lining sections, following
manufacturer’s directions.
11. Stitch front to back at side seams from lower edge to large
dot matching seams. Back-stitch at large dot to reinforce
seam.
Press under 5/8" (1.5cm) on armhole opening edges.
Press under 1/4" (6mm) on raw edge of armhole and side
seam; stitch close to pressed edges.
12
13
12. Press under 1-5/8" (4cm) on upper edge of front to INSIDE,
forming casing.
Press under 1/4" (6mm) on raw edge.
Stitch close to lower edge of casing. Stitch back casing same
as for front.
13. Press up hem.
To EDGE FINISH the raw edge...stitch under 1/4" (6mm), zigzag, OR overlock/serge.
Slip-stitch hem in place.
2. Press under 3/8" (1cm) on unnotched edge of hat trim. Pin
WRONG side of trim over RIGHT side of crown matching
centers, having raw edges even. Baste raw edges. Stitch
close to pressed edge.
2
3. Stitch center back seam of hat crown.
RIBBON TIES VIEWS A, B
14
4
3
5
14. Cut ribbon in half. Insert ribbon through each front and back
casing. Gather up front and back along ribbon, having ends
extending evenly.
Try on garment and adjust if necessary. Pin ends of casing in
place. Stitch across ends of casing along previous stitching,
catching in ribbon. Trim ends diagonally and tie in a bow.
5. Stitch center back seam of hat brim.
6
7
15
4. With RIGHT sides together, pin hat top to upper edge of
crown, matching centers, having raw edges even. Stitch
seam. Clip curves.
6. On OUTSIDE, pin brim to crown, matching centers. Stitch
seam.
TRIM VIEW B
7. Stitch center back seam of hat crown lining, leaving an
opening to turn, as shown. Press seam open.
15. Pin rick-rack to lower edge of garment, having center 1”
(2.5cm) above finished edge, turning under and lapping one
end at one side seam. Stitch along center of rick rack. Apply
two more rows above first row, spacing 1” (2.5cm) apart.
Continue same as for Hat, see steps 4 through 6.
8
16
8. With RIGHT sides together, pin lining to hat matching
centers, having raw edges even. Stitch lower edge of hat
brim. Trim seam; clip curves.
RIBBON TIE VIEWS C, D
16. Insert ribbon through front and back casing. Gather up front
and back along ribbon, having ends extending evenly at
LEFT side.
Trim ends diagonally and tie in a bow.
TRIM VIEW C
17
17. Pin one edge of grosgrain ribbon 1/2" (1.3cm) above lower
edge of band, turning under and lapping one end at one side
seam. Stitch close to both long edges of trim.
Apply another row of ribbon 1/2" (1.3cm) below upper edge of
band in same manner..
Center novelty ribbon between upper and lower ribbons,
turning under and lapping one end at one side seam. Stitch
close to both long edges of ribbon.
© Copyright 2010—Simplicity Pattern Co., Inc. / Printed in U.S.A. / Simplicity is a registered trademark of Simplicity Pattern Co., Inc.
9. Turn RIGHT side out, turning lining to INSIDE through
opening in crown lining. Slip-stitch opening.
9
10
10. Turn hat to RIGHT side. Press. Stitch close to outer edge of
brim. Tie ribbon in a bow. Trim ends. Tack ribbon to center of
hat crown.