MGB Sun visors MGB Tonneau Covers MGB Sun visor Mounting Coil Spring

MGB Sun visors MGB Tonneau Covers MGB Sun visor Mounting Coil Spring

MGB Sun visors
MGB Sun visors
MGB Tonneau Covers
MGB Sun visor Mounting Coil Spring
This spring wraps around the
threaded end of the visor rod,
underneath the nut and cup
washer.
It puts tension on the rod to
prevent the sun visor from
pivoting unintentionally. 2 needed.
HW-WASHE-AJD7721
Reg. $1.80
Sale $1.19 ea
MGB Sun visor Mounting Cup Washer
Visors come with metal pivot rods installed.
LH visor is plain. RH visor comes with mirror.
MGB visors were originally supplied in two conditions. Early cars used to have visor rods with a
long thread. Later cars had visor rods with a short
thread. We are referring to the threaded end that
secures the visor to its cast Aluminum mounting lug
on the windshield frame.
Sun visor manufacturers in the UK have "rationalized" production and now all visors for the MGB
come with short threads.
On some cars this may pose a small problem: You
may find that insufficient thread exists on the rod to
install the nut and washer.
The solution is easy. With a 1/4" drill, carefully
deepen the hole in the top side of the visor retaining bracket(s). This will then allow the visor rod to
sit lower in the bracket, enabling you to get a nut on
the threaded end. *** DO NOT drill all the way
through the brackets when drilling or you will need
to buy new ones!
All 63-80 cars.
LH ST-SUNVI-BHH2167
RH ST-SUNVI-BHH2168
Reg. $49.50
Sale $29.95 ea
"Nyloc" MGB Sun visor Mounting Nut
A self locking nut on the end of the sun visor mounting bar is really a good idea.
Using regular nuts will only result in future frustration when they "unthread" themselves and fall off.
2 needed.
HW-NUT-GHF220
Reg. $1.00
Sale .69 ea
Mounts under the nut to retain
the sun visor into its bracket.
2 needed.
HW-WASHE-AHH8799
Reg. $1.80
Sale 1.19 ea
MGB Rubber Sun visor Clip
These clips deteriorate
from use and fail.
It is best to install 2 new
clips when replacing
your sun visors.
Fits LH or RH.
ST-CLIP-622431
Reg. $3.85
Sale $3.49 ea
-mounted on windshield
frame
Cast Aluminum bracket,
rivets onto the windshield
frame. The threaded end
of the visor-mounting rod
installed into this bracket.
It supports the visor and
allows adjustment (like if you want the visor hanging over the door window because of strong sunlight).
These brackets are correct for later type visors
with short mounting stud threaded ends.
Original for 1976-1980 cars.
They work correctly for all replacement sun visors.
Fits LH or RH. 2 needed.
ST-BRACK-HZA5101
Sale $15.95 ea
Chrome Bullet Mirrors
Chrome Bullet Mirrors
Just arrived, brand new stock from
Newton in England.
These are full tonneau's, Zippered
down the middle. They have both
headrest and steering wheel pockets.
A tonneau makes a great accessory
item for an MGB;
-A tonneau can be used during cool
days for your driving pleasure. Simply zip open the driver's side and
keep your lower body warm and comfy under the
cover (provided that you're by yourself).
-A tonneau can be used as a rain cover if you don't
care to erect the convertible top-or if it's damaged
or missing.
Tonneau covers are supplied with zippers and
rear "tongue" fasteners installed. The "lift-the-dot"
fasteners are included with an installation tool. They
sic bullet shape.
It is chrome-plated brass and should stand up well.
For years I never even knew what these things
were. Some of the parts cars that I dismantled had
this funny looking pair of bent up steel pipes-usually in a mouldy old bag of some sort.
Finally I got educated about their use.
The tonneau bars each have a little flat end piece.
This is inserted into its mating "receptacle" on the
car where the top frame pivots bolt on (one on
each side, behind the doors).
The two pieces then slide together in the middle.
The tonneau bars support the tonneau cover so it
doesn't droop behind the seats. This would be
especially pronounced if it were raining out.
I suppose you could fabricate something at home
out of junk steel to do the same job, but it wouldn't
be original. Chances are that it wouldn't look very
nice either.
A lot of MGBs have lost their tonneau bars at some
point. Probably as these cars changed hands over
the years, a lot of subsequent owners probably
didn't know what to do with these things, so they
threw them out!
Last year we completely sold out of used bars. We
just found a few sets at a deeply discounted price
over in the old country, so we brought them in.
These are brand new bars.
Comes as set of LH & RH pieces. Bag NOT included. Fits any 63 - 80 MGB.
CT-TONNE-AHH6529-3
Reg. $88.85
Limited Stock
Sale $69.95 per set
This is a set of black nylon carpets with bound
edges, and embroidered MG Logo.
Includes both LH & RH front floor carpets.
These fit very nicely over existing original carpets. Alternatively they can be put on bare floor
pans (if your old carpet is ratty or missing).
Fits any 1968 - 1980 MGB or MGB GT.
ST-MATS-CK171A
Sale $99.95
- Fits early cars
We now carry an overmat set for 3-synchro MGBs
too. It is the same set as listed above except that the
inner edges are contoured to fit the early floor
panels. Fits any 1963 - 1967 MGB with "Steel"
dash.
ST-MATS-CK170A
1 (519) 337-3232
Sale $319.00
MGB Over mat Set with MG Logo
MGB Over Mat Set with MG Logo
Customer Service
Reg. $435.00
Mat Sets
Reg. $125.50
Most TR's from the 60's and 70's as well as many
earlier MGs came with chrome bullet mirrors. These
same mirrors were also used on Sunbeams,
Healey's, and a variety of other English sports
cars of that era.
Most of the original mirrors were made by Walpress
(The Walsall Pressing Company) in England.
More recently, all the replacement mirrors seem to
be manufactured a little further East of there…
The original mirrors were cast from Pot-Metal and
chrome plated. They suffered badly from pitting if
not washed and waxed regularly.
The original mirrors "dried up" in the early 1980s.
Several different brands of replacement mirrors
have been supplied since that time.
Some mirrors have been very nice, others less
so.
Last year we were offered a UK supplied replacement bullet mirror of about the right diameter. It
looked pretty nice, until you picked it up. The entire
mirror weighed only a few ounces because it was
chrome plated PLASTIC!!!
We nixed that one immediately.
We now have a nice looking mirror in stock. It has
a 3 ½" diameter mirror and it has the correct, clas-
are not pre-installed owing to differences in top
stud location on car bodies. They never seem to
be in exactly the same place!
Black vinyl material with red piping.
Fits any 1970 - 1980 MGB roadster.
CT-TONNE-BHH1036AR
MGB Tonneau Bar Set
MGB Sun visor Pivot Brackets
Reg. $24.45
MGB Tonneau Covers
Sale $99.95 set
TR6 - TR4 Over mat Set with TR' Logo
Reg. $125.50
MGB Rubber Floor Mat Sets
These mirrors are supplied with both short and
long bases as needed.
The short base is 2 ¼" long and has two mounting
studs that are 1" apart. The short base is by far the
most commonly used.
The mirror is also supplied with a long base if
needed. The long base is 4 ½ long and the mounting holes are 3 ½" apart. The long base is usually
used to cover pre-existing holes in the door or
fender.
Rubber mounting pads are supplied with the mirror in both sizes as well. If you are using the short
base, you simply unscrew the long base and discard it.
Fits LH or RH.
MI-DOOR-MTR01
Reg. $78.50
24 Hour Fax Machine
Sale $54.95 ea
1 (519) 336-5936
Heavy black
rubber mats with
the MG marque
logo moulded in.
These are copies of the "Amco"
brand mat sets
that were very
popular in the 60's & 70's. These mats improve
the appearance of the car and preserve the carpet
in the heaviest wear areas, the front floors.
Mats run from just in front of the seats almost all the
way up front to the foot wells.
Set includes mats for both front floors.
No carpets in your car? Surprisingly this is not a
rare phenomenon. Installing a rubber mat set will
improve the looks of your interior and preserve
the paint on your floor pans.
Fits 1968 - 1980 MGB or MGB GT.
ST-MATS-6815-2
Reg. $56.50
Sale $49.00 pr
Canada Wide Toll Free Order Line
1-800-265-743 7
This is a set of black nylon carpets with bound
edges, and embroidered Triumph Logo.
Includes both LH & RH front floor carpets.
These fit very nicely over existing original carpets.
Alternatively they can be put on bare floor pans (if
your old carpet is ratty or missing).
Fits any 1962 - 1976 TR6 thru TR4.
ST-MATS-CK2047A
Reg. $125.50
Sale $99.95
TR3 - TR6 Rubber Floor Mat Set
Heavy black rubber
"AMCO" pattern
mats with the Triumph logo.
Fits 1960-1976 cars
ST-MATS-6819-2
Reg. $56.50
Sale $49.00 pr
3