Installation Guide And Users Manual

Installation Guide
and Users Manual
SPAGNA VETRO 218 Series
IMPORTANT:
Read and save these instructions.
NOTICE:
Installer: Leave this guide with the homeowner
Homeowner: Keep this guide for future reference
Island Mount Range Hood
Important Safety Notice
Read all Instructions before Installing and operating this appliance
•
•
•
•
•
The installation in this manual is intended for qualified installers, service technicians or persons with
similar qualified background. Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards, including fire-rated construction.
DO NOT attempt to install this appliance yourself. Injury could result from installing the unit due to
lack of appropriate electrical and technical background.
Range hood may have very sharp edges; please wear protective gloves if it is necessary to remove any
parts for installing, cleaning or servicing.
Activating any switch ON before completing installation may cause ignition or an explosion.
Due to the size and weight of this range hood, two people installation is recommended.
To reduce the risk of fire, electric shock, or injury to persons:
•
•
•
•
•
•
•
•
•
•
•
•
For general ventilating use only. DO NOT use to exhaust hazardous or explosive materials and vapors.
The combustion air flow needed for safe operation of fuel-burning equipment may be affected by this
unit’s operation. Follow the heating equipment manufacturer’s guideline and safety standards such
as those published by the National Fire Protection Association (NFPA), and the American Society of
Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.
Before servicing or cleaning unit, switch power OFF at service panel and lock service panel to prevent power from being switched ON accidentally.
Clean grease laden surfaces frequently. To reduce the risk of fire and to disperse air properly, make
sure to vent air outside. DO NOT vent exhaust into spaces between walls, crawl spaces, ceiling, attics
or garages.
Ducted fans MUST always be vented to the outdoors.
Use only metal ductwork and this unit MUST be grounded.
Sufficient air is needed for proper combustion and exhausting of gases through the duct to prevent
back drafting.
When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidden utilities.
All electrical wiring must be properly installed, insulated and grounded.
Old duct work should be cleaned or replaced if necessary to avoid the possibility of a grease fire.
Check all joints on duct work to insure proper connection and all joints should be properly taped.
Use this unit only in the manner intended by the manufacturer. If you have questions, contact the
vendor.
To reduce the risk of a stove top grease fire:
•
•
•
•
Keep all fan, baffle, spaces, filter, grease tunnel, oil container and grease-laden surfaces clean. Grease
should not be allowed to accumulate on fan, baffle, spaces, filter, grease tunnel and oil container.
Always turn range hood ON when cooking at high heat or when cooking flaming foods.
Use high settings on cooking range only when necessary.
Never leave surface units unattended at high settings. Boil overs cause smoking and greasy spillovers
that may ignite. Heat oils slowly on low or medium settings.
Page 1
Important Safety Notice
Read all Instructions before Installing and operating this appliance
•
•
•
Clean ventilating fan frequently.
Always use appropriate cookware and utensils size.
Always use cookware appropriate for the size of the surface element.
To reduce the risk of injury to persons in the event of a stove top grease fire:
•
•
•
SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn OFF the burner.
BECAREFUL TO PREVENT BURNS. NEVER PICK UP A FLAMING PAN—you may be burned.
KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames DO
NOT go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT or 911.
DO NOT USE WATER, including wet dishcloths or towels — a violent steam explosion will result.
Use an extinguisher ONLY if:
• You know you have a Class A, B, C extinguisher, and you already know how to operate it.
• The fire is small and contained in the area where it is started.
• The fire department is being called.
• You can fight the fire with your back to an exit.
To reduce the risk of injury to persons in the event of a gas leaks:
•
•
•
Extinguish any open flame.
DO NOT turn on the lights or any type of appliance.
Open all doors and windows to disperse the gas. If you still smell gas, call the gas company and fire
department, or 911 immediately.
Your safety and the safety of others is very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
WARNING
This is the safety alert symbol. This symbol alerts you to potential hazards that can hurt you and others.
All safety messages will follow the safety alert symbol and the word “WARNING”.
Euro-Kitchen, Inc. declines all responsibility in the event of failure to observe the instructions given
here for installation, maintenance and suitable use of the product.
Euro-Kitchen, Inc. further declines all responsibility for injury due to negligence and the warranty
of the unit automatically expires due to improper maintenance.
Euro-Kitchen, Inc. will not be held responsible for any damages to personal property or real estate
or any bodily injuries whether caused directly or indirectly by the range hood.
Page 2
Table of Contents
INSTALLATION
Tools needed....................................................3
Parts supplied...................................................4
Venting requirements.......................................5
Mount heights & clearance...........................5-6
Calculating vent system length.......................6
Venting methods & ductless conversion..........7
Charcoal filters & electrical requirements.......8
Preparation......................................................9
Installation................................................10-11
Installation overview.....................................11
USE AND CARE
Range hood operations.............................12-13
Troubleshooting...........................................14
Use and care information...............................15
Specifications..............................................15
Wiring diagram..............................................16
MAINTENANCE
Cleaning, replacing filter & light bulb.........17
WARRANTY
Coverage & exceptions.................................18
Disclaimer & contact information.................19
Tools needed:
Marker or
pencil
Measuring
tape
Utility knife
Adjustable Wrench
Level
Powered
screwdriver
or drill
Flat-blade
and Phillips
screwdrivers
Page 3
Range Hood (varyy with model))
Parts supplied:
Lower Standard Chimney
Upper Standard Chimney
Upper Support Frame
Lower Support Frame
D
A
Qty: 4 PCS
Qty: 4 PCS
(Optional with re-circulating kit. Pre-installed when
kit ordered together with
range hood)
Air Diverter
(Optional re-circulating kit, pre-installed
when ordered together with range hood)
B
Qty: 36 PCS
C
Support frame extension
Qty: 36 PCS
(Length varies with ceiling height)
Charcoal filter
Hex Key
Qty: 1 PCS
(Optional re-circulating kit,
pre-installed when ordered
together with range hood)
Grease/Oil Cup
(Optional with glass canopy)
Glass Canopy Screw
Qty: 4 PCS
Flappers
(Optional with glass canopy)
Flexible Duct Tube
Page 4
Venting Requirements
•
•
•
•
•
•
•
Vent system must terminate to the outside
(roof or side wall).
DO NOT terminate the vent system in an attic or other enclosed area.
DO NOT use 4” (10.2 cm) laundry-type wall
caps.
Use metal/aluminum vent only. Rigid metal/
aluminum vent is recommended.
DO NOT use plastic vent.
Always keep the duct clean to ensure proper
airflow.
Calculate the following figures before installation:
1. Distance from the floor to the ceiling.
2. Distance between the floor to the countertop/stove.
3. Distance between the countertop/stove
to the range hood (recommend* 28” to
31”).
4. Height of hood and duct cover.
Height & Clearance
Support
Structure
Maximum* ceiling clearance
101” at 31” hood mounting
height above countertop/stove
(may vary with different
model). Chimney extensions
available for higher ceiling.
Standard
Upper
Chimney
Extension available*
Standard
Lower
Chimney
Extension available*
Range hood
For the most efficient & quiet operation:
•
•
•
•
•
•
•
•
•
•
A distance of 28” to 31” is recommended*
between stove top and the bottom of range
hood.
It is recommended that the range hood be
vented vertically through the roof through 6”
(17.8 cm) or bigger round metal/aluminum
vent work.
The size of the vent should be uniform.
Use no more than three 90° elbows.
Make sure there is a minimum of 24” (61
cm) of straight vent between the elbows if
more than one elbow is used.
DO NOT install two elbows together.
The length of vent system and number of
elbows should be kept to a minimum to provide efficient performance.
The vent system must have a damper. If
roof or wall cap has a damper, DO NOT
use damper (if supplied) on top of the range
hood.
Use silver tape or duct tape to seal all joints
in the vent system.
Use caulking to seal exterior wall or roof
opening around the cap.
Min: 28”
Max: 31”
Max*: 101”
Countertop/Stove
36” base
* Higher ceiling requires chimney extension.
Available at http://www.euro-kitchen.com.
Product ID:
SV218-ACS-CCE or SV218-ACS-EXCCE
* Due to different ceiling height configurations, recommended height may not be applicable.
Page 5
IMPORTANT:
• A minimum of 6” round (standard for this range hood) or 3-1/4 x 10” rectangular duct (purchased separately)
must be used to maintain maximum airflow efficiency.
• Flexible 6” round duct provided for convenience, always use rigid type metal/aluminum ducts if available to
maximize airflow when connecting to provided duct.
• Please use Duct Run Calculation below to compute the total available duct run when using elbows, transitions
and caps.
• ALWAYS, when possible, reduce the number or transitions and turns. If long duct run is required, increase
duct size from 6” to 7” or 8”. If a reducer is used, install a long reducer instead of a pancake reducer. Reducing duct size will restrict airflow and decrease airflow, thus reduce duct size as far away from opening as possible.
• If turns or transitions are required: Install as far away from opening and as far apart, between 2, as possible.
• Minimum mount height between stove top to hood bottom should be no less than 28-inch*.
• Maximum mount height between stove top to hood bottom should be no higher than 31-inch*.
• It is important to install the hood at the proper mounting height. Hoods mounted too low could result in heat
damage and fire hazard; while hoods mounted too high will be hard to reach and will loose its performance
and efficiency.
• If available, also refer to stove top manufacturer’s height clearance requirements and recommended hood
mounting height above range.
* Due to different ceiling height configurations, recommended height may not be applicable.
Minimum Duct Size:
• Round - 6” minimum
• Rectangular - 3-1/4 x 10” minimum (requires a 6” to 3-1/4x10” adaptor, not supplied)
Calculating vent system length
To calculate the length of the system you need, deduct the equivalent feet for each vent piece used in the system
from the recommended maximum duct run.
Duct Run Calculation:
Recommended maximum run
6” or 3-1/4 x 10” duct
50 ft
Vent piece deduction
Each 90º elbow used
9 ft
Each 45º elbow used
5 ft
Each 6” to 3/14 x 10” transition used
7 ft
Side wall cap with damper
0 ft
Roof cap
0 ft
Duct Run Calcuation example:
One roof cap, two 90º elbow, and one 45º elbow used:
0ft + 9ft + 9ft + 5ft = 23ft used.
Deduct 23ft from 50ft, 27ft maximum available for
straight duct run.
Page 6
Venting Methods
•
•
This island canopy range hood is factory set for venting through the roof or wall. For non-vented (re-circulating) installations, see Recirculating (Non-Vented) Kit on page 10.
Vent work can terminate either through the roof or wall. To vent through a wall, a 90° elbow is needed.
IMPORTANT:
•
•
•
•
NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or
garages. All exhaust must be ducted to the outside.
Use metal/aluminum duct work only.
Fasten all connections with sheet metal screws and tape all joints with certified Silver Tape or Duct Tape.
Use caulking to seal exterior wall or roof opening around the cap.
Option 1: Vertical roof venting
Option 2: Horizontal wall venting
Roof cap
Side wall cap
Ductless Conversion
•
•
•
Ductless conversion is intended for applications where an exhaust duct work is not possible to be installed.
When converted, the hood functions as a purifying hood rather than an exhaust hood. Fumes and exhaust
from cooking is drawn and filtered by a set of charcoal filters. The air is then purified and re-circulated back
within the home.
We recommend to ALWAYS exhaust air outside of the home by employing existing or installing new duct
work, if possible. Only when the exhaust option is not possible should you recourse to converting the hood
into a purifying unit.
When converted to be a “purifying” unit, a set of charcoal filters and an air-diverter are required in addition
to its standard aluminum filter set. Available at http://www.euro-kitchen.com (Product ID: SV218-ACS-RECIR). The standard aluminum filters are intended to capture residue from cooking, the optional charcoal filters help to purify fumes exhausted from cooking, and the optional air-diverter
Page 7
redirects filtered clean air back to the house.
Charcoal Filter Installation
NOTE: The charcoal filters are preinstalled if you purchased the range hood with re-circulating kit from us.
1. Remove aluminum filters on hood.
2. Position the charcoal filters onto each side of the motor and turn until it locks. Re-install aluminum filters.
3. Charcoal filters must be replaced after 120 hours of use (or approximately every 2 to 3 months based on
the average of 1 to 2 hours of daily cooking time). Available at http://www.euro-kitchen.com (Product ID:
SV218-ACS-CF-KIT).
Electrical Requirements
IMPORTANT: Observe all governing codes and ordinances.
It is the customer’s responsibility:
• To contact a qualified electrical installer.
• To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/
NFPA 70 — latest edition*, or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22. 2 No.
0-M91 - latest edition** and all local codes and ordinances.
If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that
the ground path is adequate.
A 120-Volt, 60 Hz, AC-only, fused electrical supply is required on a separate 15-amp circuit, fused on both sides
of the line.
DO NOT ground to a gas pipe.
Check with a qualified electrician if you are not sure that the range hood is properly grounded.
DO NOT have a fuse in the neutral or ground circuit.
IMPORTANT: Save this Installation Guide for electrical inspector’s use.
The range hood must be connected with copper wire/plug only.
The range hood should be connected directly to the fused disconnect (or circuit breaker) box through flexible
armored or non-metallic sheathed copper cable. A U.L. - or C.S.A. - listed strain relief must be provided at each
end of the power supply cable.
Wire sizes (copper wire only) and connections must conform with the rating of the appliance as specified on
the model/serial rating label. Wire sizes must conform to the requirements of the National Electrical Code
ANSI/NFPA 70 — latest edition*, or CSA Standards C22. 1-94, Canadian Electrical Code Part 1 and C22.
2 No. 0-M91 - latest edition** and all local codes and ordinances. A U.L. - or C.S.A. - listed conduit connector must be provided at each end of the power supply cable (at the range hood and at the junction box).
Copies of the standards listed may be obtained from:
* National Fire Protection Association
Batterymarch Park
Quincy, Massachusetts 02269
** CSA International
8501 East Pleasant Valley Road
Cleveland, Ohio 44131-5575
Page 8
Preparation
Advanced Preparations:
1. Be familiar with the controls of the range hood by reading
through Range Hood Operations, Page 12.
2. Place the range hood on a flat, stable surface. Connect the
Excessive Weight
range hood to a designated standard outlet (120-Volt, 60Hz,
Require three or more person to move and
AC only) and turn on the range hood. Verify all operations install this range hood. Spinal or other bodiof the range hood by referring to Range Hood Operations,
ly injuries could occur if it is not followed.
Page 12.
3. Place all supplied parts and required hardware on a flat, stable surface and verify the existence of all supplied
parts listed on Page 4.
4. Carefully remove the white plastic protective coat from the chimney covers and range hood.
WARNING
Preparations:
NOTE: To avoid damage to your hood, prevent debris from entering the vent opening.
1. Determine and mark the center line on the ceiling where the range hood will be installed. Make sure there is
proper clearance within the ceiling or wall for exhaust vent.
2. Due to the weight and size of this unit, please make sure that the support system or framework being used is
stable and secure in the wall.
3. Put a thick, protective covering over counter top, cook top or range to protect from damage or dirt. Remove
any hazardous objects around the area when installing.
4. Mark the locations of the support mounting bracket holes, vent cutout (if used) and power supply cable cutout
on the ceiling. Use drill and saber saw or keyhole saw to cut openings for power supply cable and vent (see
Venting requirements and Electrical requirements, Pages 6-8).
5. If venting to the outside install vent system (see Venting Requirements, Page 5). Use caulking to seal exterior
wall or roof openings.
6. Disconnect main electrical supply, prepare and run electrical wiring through ceiling or wall. Leave approximately 12” of electrical cord hanging from the ceiling. Do not restore power until wiring is completed.
7. Disconnect power cord, remove the aluminum filter by pressing on the latch toward the direction of solid arrow while holding the metal handle, gently pull the aluminum filter toward the direction of dashed arrow as
shown in Figure 1.
8. Remove the grease cup by sliding it sideway, see Figure 2 for location of the grease cup.
9. Set aside the aluminum filters and grease cup until the range hood is properly installed.
10. If the range hood comes with a glass canopy and has not already been mounted to the hood, loosen the four
canopy screws and washers from the hood top, carefully place the canopy on the hood top, and loosely tighten
the four canopy screws along with washers. DO NOT put excessive pressure against the glass.
WARNING
Severe Injury
Rotating fan can cause severe
injury. Stay clear of fan when
motor is running.
Figure 1
Figure 2
Page 9
Installation
1. Align upper support frame with holes in ceiling. Mount
the upper support frame to the ceiling using four “A”
screws (for sheet rock only). Make sure that the upper
support frame is securely fastened to the joist or support
in the ceiling. Attach support frame to ceiling using anchors recommended for your type of ceiling:
• Sheet rock ceiling: Attach support frame to ceiling
joists or stud blockings if possible. If ceiling joists
or stud blockings are not available, it is required to
build a supporting structure behind the sheet rock for best weight support.
• Concrete ceiling: Use designated screws (not provided).
• Wood ceiling: Use at least 4” long wood screws (not provided).
2. Recirculating (Non-Vented) Kit: If Re-Circulating Kit is not purchased, skip this step. Place the air diverter
inside upper support frame so that its 6” round hole faces downward into the lower support frame and secure
it with four “D” bolts. Be sure to let through the 12” of electrical cord hanging from the ceiling.
3. Position the support frame extensions at the inside corners of the support frames, adjust and mark each support frame extension as necessary to achieve the proper height for the range hood to be set away from the cook
top. (See Height and Clearance on Page 5 and Installation Overview on next page).
4. Fasten the support frame extension onto the lower support frame using four “B” bolts and “C” nuts as shown
in Figure 3. Repeat this step for rest of the support frame extensions. IMPORTANT: Always use first and
second holes on the support frame extensions.
5. Calculate the height of the duct tube and extend approximately 6 inches longer than required, connect the upper end of the duct tube to the vent system.
6. Position the lower support frame with support frame extensions to the upper support frame, fasten each extension with four “B” bolts and “C” nuts as shown in Figure 3.
7.
Slide the upper chimney cover over the completed
support frame and fasten with two “D” bolts to the
upper support frame. (See Figure 3 for illustrations).
Stud
8.
Slide
the lower chimney cover around the lower supblockings
port frame and around the upper chimney cover. Have
second person to hold it in position. (See Figure 4).
Secure
upper
support
frame
Slide up and secure
upper chimney
Adjust
support
frame
extensions
Slide up, hold in position
and secure lower chimney
to range hood
Insert lower
support
frame with
extensions
Figure 3
Figure 4
Page 10
Installation (Continued)
9. Have a third person raise up and hold the island range hood in position, connect power plug to the 12” hanging
electrical cord, and connect the duct work to the range hood.
10. Mount the hood to the lower support frame using four “B” bolts and four “C” nuts: Securely fasten two “C”
nuts to two “B” bolts by reaching up from the underside of the hood. Repeat this step to secure the other side
using two “C” nuts to two “B” bolts.
11. After all four “B” bolts and four “C” nuts securely fastened, connect the lower end of the duct tube to the hood
and slide the lower chimney cover down carefully so that it sits on top of the hood.
12. Install grease cup and aluminum filters then check the operation of the range hood.
Installation Overview
A
D
Qty: 4 PCS
(Optional with
re-circulating
kit. Pre-installed
when kit ordered
together with
range hood)
C
Qty: 32 PCS
Hex Key
Qty: 1 PCS
(Optional with glass canopy) (Optional with glass canopy)
NOTE:
• A screws are designed for dry wall.
Not to be used with any other types
of walls.
• A distance of 28” to 31” is recommended* between stove top and the
bottom of range hood.
• Always use first and second holes
on the support frame extensions to
secure lower support frame.
* Due to different ceiling height configurations, recommended height may not be
applicable.
Air Movement Direction
Qty: 32 PCS
Upper support frame
B C
B
Glass Canopy Screw
Qty: 4 PCS
Re-circulating kit exhaust
(Re-circulating kit not shown)
IMPORTANT: Minimum height = Longest chimney + 1½-inch
A
D
Qty: 4 PCS
Support frame extensions
(Hole to hole distance: ≈⅝-inch)
B C
Duct work and electric
wiring region
Lower support frame
6” Round duct (exhaust)
B C
Electric circuit box
Motor housing
Island mount
range hood
Page 11
Range Hood Operations
Control Panel Layout and Buttons Configurations:
Power
Decrease Value
Light
Increase Value
Blower Power Indicator
Power-On Elapsed Digital Timer
Blower Speed Indicator
Power-Off Delay Digital Timer
Light Power Indicator
Power-Off Delay Timer Indicator
The island canopy hood is designed to remove smoke, cooking vapors and odors from the cook top area. For best
results, start the range hood before cooking and allow it to operate several minutes after the cooking incomplete
to clear all smoke and odors from the kitchen.
•
•
Button functions:
• Power: Power ON/OFF and activate power-off delay timer.
• Decrease Value: Blower (motor) speed decrease, timer value decrease, and enter timer mode.
• Increase Value: Blower (motor) speed increase timer value increase, and cumulative timer reset.
• Blower Power Indicator: Lights up when blower (motor) is running.
• Blower Speed Indicator: Shows current blower (motor) speed (1-6).
• Light Power Indicator: Lights up when lights turned on.
• Light: Turns ON/OFF and dim halogen lights.
• Power-On Elapsed Digital Timer: Indicates the accumulated time the system is running.
• Power-Off Delay Digital Timer: Indicates the length of time left for delay off function.
• Power-Off Delay Timer Indicator: Lights up when auto-shutdown delay timer function is on.
Controls:
• Automatic cleaning reminder:
• When blower (motor) starts to rotate, cumulative running time will be shown in Power-On Elapsed
Digital Timer. This timer icon flashes when 30 hours is up and reminds user to clean the aluminum
filter.
• After cleaning the filter and when the motor is not in use, press and hold Increase Value button over 3
seconds to reset the timer. Please note that turning off the system will not reset the Power-On Elapsed
Digital Timer.
• Adjusting the blower (motor) speed:
• Press Power button once to turn on the system. The Blower Power Indicator icon flashes showing that
the blower (motor) is ready. Decrease Value button will decrease the speed of the blower (motor) from
6 to 1 (strongest to quietest). Increase Value button will increase the speed of the blower (motor) from
1 to 6 (quietest to strongest).
• Press Power button once to turn off the system.
Note: The system saves user configurations, settings such as light, timer and blower (motor) speed will remain the same the next time it is turned on.
Page 12
Range Hood Operations (Continued)
Control Panel Layout and Buttons Configurations:
Power
Decrease Value
Light
Increase Value
Blower Power Indicator
Power-On Elapsed Digital Timer
Blower Speed Indicator
Power-Off Delay Digital Timer
Light Power Indicator
•
Power-Off Delay Timer Indicator
Controls:
• Adjusting the timer function:
• While the blower (motor) is not running, press and hold Decrease Value button over 3 seconds to
enter timer mode. Adjust to desired period of delay off timer by pressing Increase Value or Decrease
Value button (minimum 1 minute to maximum 15 minutes). This setting will be saved immediately.
• Activating the timer function:
• While the blower (motor) is running, press and hold Power button for over 3 seconds to activate
delay off timer. Power-off delay indicator will lit up and power-off delay digital timer will begin to
countdown, when it reaches zero, the blower (motor) will shut down.
• Adjusting the light:
• Press Light button once to turn on the lights, and once again to turn off the lights.
• While the lights are off, press and hold Light button for over 3 seconds to dim the lights from low to
high. Level of brightness will be stored in system’s memory.
CAUTION: DO NOT touch the lights until switched OFF and cooled.
Note: Light settings are independent from other settings (including power-off delay) and lights has to be
manually turned on or off.
Note: The system saves user configurations, settings such as light, timer and blower (motor) speed will remain the same the next time it is turned on.
Page 13
Troubleshooting
1. If the range hood or halogen light does not operate
after installation:
•
•
Check if the range hood has been plugged in, make
sure that all power has been turned back ON, fused
not blown and all electrical wiring are properly connected.
Swap out light assembly to working ones to determine whether it is caused by defective bulbs. See
Replacing the light bulbs on Page 17.
2. The range hood vibrates when the blower is on:
•
The range hood might not have been secured properly on to the ceiling or wall. Check with your installer
3. The blower or fan seems weak:
•
Check that the duct sized used is at least 6” or 3-1/4
x 10”. Range hood WILL NOT function efficiently
with insufficient duct size. For example: 7” duct
over 6” hole and loosely secured.
Check if duct is clogged or if damper unit (half-circular flapper) is not installed correctly or opening
properly. A tight mesh on a side wall cap unit might
also cause restriction to the air flow.
•
4. The lights work but the blower is not spinning at all, •
is stuck or is rattling.
The blower might be jammed or scraping the bottom due to shipping damage. Please contact us immediately.
5. The hood is not venting out properly:
Make sure the distance between the stove top and
the bottom of the hood is within* 28” and 31” in
distance. *Due to different ceiling height configurations, recommended height may not be applicable.
Reduce the number of elbows and length of duct
work. Check if all joints are properly connected,
sealed, and taped.
Make sure the power is on high speed for heavy
cooking.
•
•
•
6. Purpose of the slots/holes/openings near the top of
the upper chimney:
•
These slots/holes/openings are used to exhaust
cleaned air with optional re-circulating kit. If you
did not install one, you do not need them.
NOTE: For all other inquiries, please contact us. Our contact information can be found on Page 18.
Page 14
Use and Care Information
Operations:
•
•
•
•
•
Read and understand all instructions and warnings in this manual before operating the appliance. Save these
instructions for future reference.
Always leave safety grills and filters in place. Without these components, operating blowers could catch on to
hair, fingers and loose clothing.
NEVER dispose cigarette ashes, ignitable substances, or any foreign objects into blowers.
NEVER leave cooking unattended. When frying, oil in the pan can easily overheat and catch fire. The risk of
self combustion is higher when the oil has been used several times.
NEVER cook on “open” flames under the range hood. Check deep-fryers during use: Superheated oil may be
flammable.
Cleaning:
•
•
•
The saturation of greasy residue in the blower and filters may cause increased inflammability. Keep unit clean
and free of grease and residue build-up at all times to prevent possible fires.
Filters must be cleaned periodically and free from accumulation of cooking residue (see cleaning instructions
on Page 17). Old and worn filters must be replaced immediately.
DO NOT operate blowers when filters are removed. Never disassemble parts to clean without proper instructions. Disassembly is recommended to be performed by qualified personnel only. Read and understand all
instructions and warnings in this manual before proceeding.
Specifications
Body
Power Rating
General Input Power
Motor Input Power
Motor Revolution
Levels Of Speed Control
Maximum Airflow
Air Pressure
Noise Level (dB / sone)
Motor Type
Fan Type
Control Type
Filtration Type
Illumination
Venting Size
Interference Protection
Specifications*:
Stainless Steel / Tempered Glass
120V / 60Hz (USA & Canada standard)
358 W (218W + 4x35W)
218 W
600 RPM (±10%) to 1800 RPM (±10%)
6 Levels
900 CFM
320 pa
Approximately 23 / 0.3 to 68 / 7.0 (Lowest to highest Speed)
Dual Chamber Ultra Quiet
Dual Centrifugal / Sirocco
Dual Electronic Control Panels with LED Display
Aluminum Filter with Reversible Handle
35W 120V Maximum, Dimmable
Top, 6 inches Round
Radio Frequency Interference Protected
* Subject to change without notice, please visit http://www.euro-kitchen.com for details.
Page 15
Wiring Diagram
Page 16
Maintenance
SAFETY WARNING: Never put your hand into area housing the fan while the fan is operating!
For optimal operation, clean range hood and all baffle/spacer/filter/grease tunnel/oil container regularly. Regular care will
help preserve the appearance of the range hood.
Cleaning Exterior surfaces:
• Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent (e.g. Comet
Power Scruv®, EZ-Off® oven cleaner), or steel wool/scoring pads, which will scratch and damage the stainless steel
surface. For heavier soil use liquid degrease such as “Forumla 409®” or “Fantastic®” brand cleaner.
• If hood looks splotchy (stainless steel hood), use a stainless steel cleaner to clean the surface of the hood. Avoid getting
cleaning solution onto or into the control panel. Follow directions of the stainless steel cleaner. CAUTION: Do not
leave on too long as this may cause damage to hood finish. Use soft towel to wipe off the cleaning solution, gently
rub off any stubborn spots. Use dry soft towel to dry the hood.
• After cleaning, you may use non abrasive stainless steel polish such as 3M® or ZEP®, to polish and buff out the stainless
luster and grain. Always scrub lightly, with clean cotton cloth, and with the grain.
• DO NOT allow deposits to accumulate or remain on the hood.
• DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface and cause rusting.
• DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel
for extended periods. Many of these compounds contain chemicals, which may be harmful. Rinse with water after exposure and wipe dry with a clean cloth.
Cleaning Aluminum Grease Filter / Stainless Steel Filterless Grill:
IMPORTANT: Drain oil from oil containers before oil and residue overflow!
• The metal filters fitted by the factory are intended to filter out residue and grease from cooking. It need not be replaced
on a regular basis but are required to be kept clean.
• Filters should be cleaned after every 30 hours of use.
• Remove and clean by hand or dishwasher. Spray “Formula 409®” or equivalent degreasing detergent and leave to soak
if heavily soiled. Dry filters and re-install before using hood.
Replacing Filters:
• Should filters wear out due to age and prolonged use, replace with following part number:
Product ID: SV218-ACS-AF/SF (Available at http://www.euro-kitchen.com)
• Note: Also replace damaged filter that has punctured or broken mesh, bent or broken frame.
Replacing the light bulb:
• This range hood uses halogen bulb: type (GU10) 35W 120V.
Product ID: SV218-ACS-GU1035W
(Available at http://www.euro-kitchen.com)
• Make sure the range hood is unplugged or turn OFF breaker.
• Make sure the lights are cool to touch, carefully align the arrow on the inner ring with the arrow on the outer ring where it
says OPEN. The inner ring will loosen and the light bulb will
be available for removal. Install a new halogen light bulb and
reverse the steps.
• Turn ON breaker and range hood to test for operation.
Align arrows on both rings
WARNING
Hazard of Burns!
Light bulb become extremely hot when turned on.
DO NOT touch bulb until switched off and cooled.
Touching hot bulbs could cause serious burns.
Page 17
Warranty
TO OBTAIN SERVICE UNDER WARRANTY:
Yoou mu
Y
You
must
st pre
rese
sent
se
nt prooff of
of or
oriig
igin
inall purch
chas
has
asee da
date
date
te..
Plea
Pl
ease
se provi
vid
ide
de aann or
oriig
igin
inall dattedd prooff of
of pu
p rc
rchhase
hase (sa
salles
les re
rece
ceiip
ipt / invo
invoiic
ice)) in
in or
ordder
der to
to obt
obtai
ain
in se
serv
rviice
ice un
undder
der wa
warr
rran
antty
ty.
One Year Parts Warranty:
For one year from the date of original purchase, Euro-Kitchen, Inc. (“Euro-Kitchen”) will provide free of charge, nonconsumable replacement parts or components that failed due to manufacturing defects. Subject to the conditions and
limitations set forth below, Euro-Kitchen will, at its option, either repair or replace any part of its products that prove
defective by reason of improper workmanship or materials. Repaired parts or replacement products will be provided
by Euro-Kitchen on an exchange basis, and will be either new or refurbished to be functionally equivalent to new. The
consumer is responsible for all shipping costs. Consumable parts not covered by this warranty include but not limited
to: Light bulbs, metal, aluminum and charcoal filters.
Who is Covered:
This warranty is extended to the original purchaser for products purchased for ordinary home use in the continental US.
(Customer in Canada, Hawaii and Alaska, this warranty is limited).
This Warranty Will Be Voided When:
Product damaged through negligence, improper installation, accident, abuse, misuse, natural disaster, insufficient or
excessive electrical supply, abnormal mechanical or environmental conditions, or any unauthorized disassembly, repair,
modification, or failure to follow installation instructions. When product is used commercially or other than its intended
purpose. Damaged because of improper connection with equipment of other manufacturers. Repaired or modified by
anyone other than Euro-Kitchen’s authorized agents. This limited warranty also does not apply to any product on which
the original identification information has been altered, obliterated or removed, has not been handled or packaged correctly, has been sold as second-hand or has been resold contrary to the US export regulations.
What is Not Covered:
Consumable parts such as light bulbs, metal and charcoal filters. The natural wear of finish, and wear due to improper
maintenance, use of corrosive and abrasive cleaning products, pads, and oven cleaner products. Chips, dents or cracks
due to abuse, misuse, freight damage, or improper installation. Damage of product caused by accident, fire, floods or act
of God. Euro-Kitchen is not liable for, and does not cover under warranty, any loss of properties or any costs associated
with removing, servicing, installing, or determining the source of problems with Euro-Kitchen products.
This warranty is valid in the United States and Canada. It is non-transferable and applies only to the original purchaser and
does not extend to subsequent owners of this product. Any applicable implied warranties, including the warranty of merchantability, are limited in duration to a period of express warranty as provided herein beginning with the date of original
purchase at retail and, no warranties, whether express or implied, shall apply to this product thereafter.
To obtain warranty service, you may contact Euro-Kitchen, Inc., its dealer or distributor from which you purchased the
Euro-Kitchen product. Please confirm the terms of your dealer’s or distributor’s policies prior to contacting. Typically, you
must include product identification information, including model number and batch number (if applicable) with a detailed
description of the problem you are experiencing. You must also include proof of the date of original retail purchase as evidence that the product is within the applicable warranty period.
The information in this document is subject to change without notice, please visit http://www.euro-kitchen.com for updated details.
Page 18
Disclaimer
Carefully inspect all items for damages before accepting delivery. note any damages on the freight bill or
express receipt. request name and signature of the carrier’s agent and keep copy to support your claim. Upon
acceptance of items, owner assumes responsibility for its safe arrival. Report damages to the carrier and file
a claim immediately. Failure to do so may result in the denial of your claim. The carrier will furnish you with
necessary forms for filing a claim.
Damages caused during transit are not covered under our warranty. Please contact us to file an insurance claim.
Please inspect contents of package(s) carefully upon receiving! We must be notified of any damages and/or
missing parts within five (5) days upon your receipt of package(s). Claims will not be accepted after five (5)
days. NOTE: Items were thoroughly tested and carefully packed in our factory before shipping.
Products must be returned in good working condition with ALL original parts and documentation packed in
ALL original cartons, fillers and shipping cartons. A restocking fee of 15% will be charged for all approved
return(s). Exchanges or returns may not be accepted if any packaging is missing.
Make sure to inspect the hood for damages and defects before installation. Appearance flaws of the hood found
after installation and not affecting hood performance is not covered under our warranty for returns or exchanges. Service visits not covered under warranty will carry a service charge.
Before Installation: Return for exchange or refund (please see above for acceptable returns).
After Installation: NO exchange or refund.
Contact Us
If you need any assistance, please call us at (510) 266-0099 or email us at sales@euro-kitchen.com. Please have
your order number and model of the range hood ready. This information will help us better respond to your request.
If you need replacement parts, we recommend that you only use Euro-Kitchen, Inc. genuine parts. Euro-Kitchen,
Inc. accessories and parts are engineered and designed specifically for Euro-Kitchen, Inc. range hoods, each is
rigorously tested assuring the utmost in durability and reliability, providing a factory match, factory-installed appearance and functionality tailored to each individual range hood model.
To obtain warranty service, you may contact Euro-Kitchen, Inc., its dealer or distributor from which you purchased
the Euro-Kitchen product. Please confirm the terms of your dealer’s or distributor’s policies prior to contacting.
Typically, you must include product identification information, including model number and batch number (if applicable) with a detailed description of the problem you are experiencing. You must also include proof of the date
of original retail purchase as evidence that the product is within the applicable warranty period.
The information in this document is subject to change without notice, please visit http://www.euro-kitchen.com for updated details.
Page 19
Your Notes
Page 20
Your Notes
Page 21
Euro-Kitchen, Inc.
2341 Industrial Parkway West
Hayward, CA 94545
Ph: 510.266.0099
Fax: 510.266.6630
http://www.euro-kitchen.com