GLITCH360KEY ULTRA INSTALLATION MANUAL

GLITCH360KEY ULTRA INSTALLATION MANUAL v1.5
This Manual will explain you how to install the Glitch360Key Ultra on your xbox 360. For more information about the Reset Glitch
Hack check our webpage http://glitch360key.fr
Required Tools :
- 1x Glitch360Key Ultra ModChip
- 1x Glitch360Spi 3.0 rev B (for programming your modchip and using eRGH)
- Kynar AWG30, AWG24 and AWG28, Soldering iron 12/15w + soldering tin
- Softwares GSU or eRGH & GKU
The Glitch360Key Ultra is easy and quick even so please take the time to read the following instructions until the END.
Programming the Glitch360Key Ultra
Download and install the software GKU.
Connect the Glitch360Key Ultra with your Glitch360Spi 3.0 rev B using the FFC Flex cable (see picture below).Then connect the
Glitch360Spi 3.0 rev B to your computer using an USB cable (Accept the drivers when prompted) then launch GKU.
*
How to program your Glitch360Key Ultra depending on your motherboard type:
Step 1 : Select your Xbox 360 (FAT or SLIM)
Step 2 : Select your Motherboard
Step 3 : Select « Glitch360Team » in Chip Manufacturer
Step 4 : Choose the timing needed for your motherboard
Step 5 : Click on the « FLASH / UPDATE » button
* : Dual Nand Feature ON/OFF
Your Glitch360Key is now programmed, you can now unplug the flex cable and install it on your Motherboard.
Installation details
Dual Nand Feature: the command wire of your Dual Nand Modchip should be connected to CMD (ex: wire #11 of the Glitch360Shark).
eRGH BenchMark Cloud: Find the best glitch setup for your motherboard!
Available from http://cloud.glitch360key.fr, the eRGH BenchMark Cloud allows you to consult the glitch setup (motherboard type,
CPU_RST/POST_OUT wire size, switch settings, timing, etc…) shared by other users! This will allow you to find the best glitch settings
for your motherboard.
You can inspire yourself of the best Benchmark results and use those setting in order to have the best glitch performance
for your Xbox 360
INSTALLATION DIAGRAM FOR TRINITY MOTHERBOARD
BASIC SWITCH SETUP FOR XBOX 360 TRINITY MOTHERBOARDS
SW1
11110010
SW2
00000000
CPU_RST (mm) D
390 AWG30
POST_OUT (mm) C
70 AWG30
Timing
Trinity 0 (Default)
These setups are basic setups! We advise you to consult the eRGH BenchMark cloud to find the best setup for your motherboard!
INSTALLATION DIAGRAM FOR CORONA MOTHERBOARD
Note #1: On Corona v3/v4, R2C7 & R2C6 (sometimes also R2C10) must be shorted or replaced with 100 Ohm resistors.
Note #2: On Corona v3/v4, the C point is not connected, you must install a POSTFIX Adapter or connect directly under the CPU.
CONFIGURATION CONSEILLEE SLIM CORONA
SW1
11000010
SW2
00000000
CPU_RST (mm) D
140 AWG28
POST_OUT (mm) C
70 AWG30
Timing
Corona 3-2 (Default)
These setups are basic setups! We advise you to consult the eRGH BenchMark cloud to find the best setup for your motherboard!
INSTALLATION DIAGRAM FOR RGH1.0 FAT MOTHERBOARDS
BASIC SWITCH SETUP FOR XBOX 360 RGH1.0 FAT MOTHERBOARDS
SW1
10010011
SW2
00000000
CPU_RST (mm) D
200 AWG30
POST_OUT (mm) C
170 AWG30
Timing
Depending on version
BASIC SWITCH SETUP FOR XBOX 360 RGH1.0 JASPER MOTHERBOARDS
SW1
10010111
SW2
00000000
CPU_RST (mm) D
200 AWG30
POST_OUT (mm) C
170 AWG30
Timing
Jasper 0 (Default)
These setups are basic setups! We advise you to consult the eRGH BenchMark cloud to find the best setup for your motherboard!
INSTALLATION DIAGRAM FOR RGH2.0 FAT MOTHERBOARDS
BASIC SWITCH SETUP FOR XBOX 360 RGH2.0 FAT MOTHERBOARDS
SW1
10011001
SW2
00000000
CPU_RST (mm) D
200 AWG30
POST_OUT (mm) C
170 AWG30
Timing
Depending on version
FAST COLD BOOT SETUP FOR XBOX 360 RGH2.0 JASPER MOTHERBOARDS
SW1
10010001
SW2
00011000
CPU_RST (mm) D
200 AWG30
POST_OUT (mm) C
170 AWG30
Timing
Depending on version
For Falcon use 1 or B or C timing, for Jasper use B timing, for Zephyr use C or D timing
These setups are basic setups! We advise you to consult the eRGH BenchMark cloud to find the best setup for your motherboard!
SWITCHS DETAILS
SW1
SW2
1. 3,3v Enable/Disable (0 for programming, 1 for glitch)
2. VCCIO 1,8v (SLIM)
3. CPU RST CAP 270pf (Trinity)
4. DISABLE 48Mhz puce (0 = Modchip 48Mhz, 1 = Motherboard)
5. CPU RST 10 Ohm (RGH2)
6. PLL Bypass Cleaner 100nf (Jasper RGH1)
7. CPU RST
8. VCCIO 1,5v (FAT)
1. CPU RST CAP +33pf
2. CPU RST CAP +33pf
3. CPU RST Cleaner 1K Ohm
4. CPU RST Cleaner 3.3K Ohm
5. CPU RST Cleaner 470pf
6. CPU RST Cleaner 680pf
7. PLL Bypass Cleaner 680pf
8. PLL Bypass Cleaner 47nf (zephyr RGH1)
Your Glitch360Key Ultra is now correctly programmed and installed
 Continue with the eRGH & Glitch360Spi 3.0 rev B Manual v1.4
 Continue with the GSU & Glitch360Shark rev B Manual v1.9
Copyrights GlitchTeam 2013 | http://glitch360key.fr/en | http://www.seb117.fr/oshop/ | http://www.flash-miiparis.com
V1.5 Glitch360Key Ultra Xbox 360 FAT & Slim
Seb117, ZackWarrior, Elyot
Made in FRANCE
Where to place the Glitch360Key Ultra
On FAT Motherboards
On CORONA Motherboards
On TRINITY Motherboards