How to install your Everlite Enduro roof: Fixing to a 2.5º pitch using the Fast Pack Accessories.

How to install your
Everlite Enduro roof:
Fixing to a 2.5º pitch using the
Fast Pack Accessories.
Fixing notes
Cutting to size
If it is necessary to cut down one
of the panels across it’s width, it
MUST be cut down a rib.
07. Refit white end caps into panel. Lower assembled panels over EL2 eaves angle. Allow enough room for verge pack.
08. Line up by sight the position of each EL61 fixing plug with the central groove
on the front face of EL2 . Drill 5mm hole, taking care not to drill into fixing plug. Screw fix. Drill 5mm drainage hole in lower groove in line with panel joints.
The same amount must be also
cut from the wall plate, eaves angle
and lock plate.
To prevent cracking the panels
should be cut using a fine tooth
saw and the sawn edges smoothed
with a fine piece of abrasive paper.
Trade tip!
Keeping the weather out.
01. Fix the firrings by screw fixing through the window glazing recess.
A dab of silicon sealant on
the underside of the EL53
clamping washer and EL56
screw will ensure even better
protection from the weather.
02. Fix EL6 wall plate at 450mm maximum centres. For added strength, attach to both firrings. The wall plate can overhang the firrings by approximately 20mm. See insert.
09. To fix at the verge drill 5mm hole at 500mm centres through rib over firring using EL53 clamping washer as a guide. Using EL56 screws, fix through clamping washer and panel into firring.
10. Position centrally EL6A locking plate and push fit into wall plate.
Fixing holes
If the wall plate isn’t used (photo
2 opposite) the panels should be
pre-drilled at the ridge end before
installing them. See below.
Ridge end
Due to Everlite Enduros
unique design, silicon
sealant is not required (or
recommended) anywhere else
during installation.
Panel
03. Drill and screw EL2 eaves angle to front of conservatory. Ensure the eaves angle overhangs supporting structure by approximately 20mm. See insert.
04. Remove white end caps from panel.
Push two EL61 fixing plugs into each panel beneath the drip nose.
Important! Remove adhesive 11. Push fit EL36 foam filler under locking bar.
12. From the inside push fit EL36 foam filler between wall plate and panel.
Locking
bar
Drilling
points
Clamping
washer
Panel
rib
An aluminium clamping washer can
be used as a template by lining it
up with the Ridge end of the panel
and a 5mm hole drilled through
the centre ribs.
backing tape on the side of the
panel.
The top surface
05. Fix panels together at each rib with the adhesive tape and slot in the steel locking bar at each junction (see insert). The panels feature a pre-cut drip nose that should face the eaves.
06. Ensure panels are positioned centrally and overhang the wall plate/eaves angle by approximately 20mm. The rib on the
first/last panel should sit on to the firring (see insert).
13. At the front, push fit EL36 foam filler into position between panel and eaves angle. This completes the sealing of the
light panels.
14. To fix verge pack barge boards cut wings off last end cap. Cut to required length and slide up side of last panel. Drill and fix into wall plate using single screw. Fit aluminium or third party flashing into wall and you’re finished!
For expert technical assistance call 01604 790780 and ask for Everlite technical
The top surface can be identified
by the pre-cut eaves drip nose
that directs rainwater into the
gutter and by the gasket in the
top channel which provides a seal
between adjacent panels.
Traditional installation:
Duopitch
ridge
Profile filler
EL36.
Screw fix end panel
through clamping washer
into PVC-U window at
600mm centres.
Fix verge flashing to PVC-U window
with proprietary fixings at 300mm
centres.
Screw fix Enduro
panels through
clamping washer
into timber or
proprietary edge
beam at head of
PVC-U glazing
system.
Screw fix clamping washer
through panel into timber
purlin
Screw fix locking plate
through Enduro panel into
timber ridge board.
Clip a ridge flashing to
locking plate to both sides
of the ridge.
Fixing without the fast pack
accessories to 5º and over.
Monopitch ridge
Screw fix a cover flashing through self adhesive
compressible foam tape to abutment wall at
450mm centres. Alternative: Dress the cover
flashing or lead over upstand flashing and welt
into brickwork joints.
Seal joint between wall and flashing with
polysulphide sealant.
Bevelled timber
purlin to suit span.
Purlin
Fit upstand flashing over a locking plate by
others and screw fix to abutment wall at
450mm centres.
Screw fix Enduro panel to timber
wall plate through locking plate and
clamping washer.
Profile filler
EL36.
Bolt bevelled timber
wallplate to abutment
wall at 900mm centres.
Abutment
Screw fix a cover flashing through self adhesive
compressible foam tape to abutment wall at
450mm centres. Alternative: Lead flashing welted
into joints.
Seal joint between wall and flashing with
polysulphide sealant.
Screw fix an abutment flashing to wall seal with
foam filler at junction of panels.
Foam filler.
Screw fix end panel through clamping
washer into timber bearer at 600mm
centres.
Bolt timber bearer to wall at 900mm
centres.
Curved or straight
Enduro panels.
Profile filler
EL36.
Eaves
Eaves flashing
by others
Gutter system
by others
Verge
Seal verge with
foam filler.