VAGtacho USB 5.0 support VDO with 24C32 or 24C64.

VAGtacho USB 5.0 support VDO with 24C32 or 24C64.
Anytools Tech Co.,Ltd engaged in automotive diagnostic tools of high-tech enterprises.
Established in 2008.
Supplies all kinds of diagnostic scanners, such as Launch x431 diagun iii,Autoboss v30,
Launch X431 Master, Launch x431 diagun, Tacho pro v2008, MB Star C3, MB Star SD C4,
GM Tech 2, AUTOCOM, renault can clip, Peugeot Lexia3 Citroen PP2000, BMW
GT1,BMW OPS, Ford VCM IDS, Nissan Consult 3, Toyota Denso, digimaster iii,X-100+,
T300+ key programmer,Super AD900 Key programmer and so on.
How to programmer keys with vagtacho usb 5.0
Switch ON ignition with any key new or old, no mater which one.
Start software, select "VDO NEW - CAN bus" from menu.
Press "Connect Selected ECU" button, after 5 seconds the data of the dash will be shown
on screen.
Press "Program New Key", software will read data from the dash and after few seconds a
new window will be open.
See the picture. ID numbers of the transponders which are stored into memory will be
shown.
www.anydiag.com
Skype:anydiag
MSN:myanytools@hotmail.com
Tel:008675536951880
Email:sales@anydiag.com
VAGtacho USB 5.0 support VDO with 24C32 or 24C64.
This is TMPro module#146 window. Insert transponder key with new Megamos ID48 chip
and program it.
Press "Add Key" and a message will be shown. Switch ON ignition with key which you
want to program! The key may be new - already programmed with TM Pro, or old - key
which has been used with the same car! Vagtacho will check the key. If this key is already
programmed to the car, or it is from another car, Vagtacho will show warning message on
screen and won't program this key!
www.anydiag.com
Skype:anydiag
MSN:myanytools@hotmail.com
Tel:008675536951880
Email:sales@anydiag.com
VAGtacho USB 5.0 support VDO with 24C32 or 24C64.
If everything is ok, Vagtacho will add the new key into the data of immobilizer and will
show ID number of new key on screen. See the red mark on the picture. Now you are
ready to program the new transponder key into the immobilizer. Press "Write Keys" to
complete programming procedure !
www.anydiag.com
Skype:anydiag
MSN:myanytools@hotmail.com
Tel:008675536951880
Email:sales@anydiag.com
VAGtacho USB 5.0 support VDO with 24C32 or 24C64.
\Press "Write Keys" and the warning window will be open. If you are sure that everything is
all right, press"Continue", otherwise press "Cancel". If you press "Cancel" nothing will
happens, and the data won't be written into immobiliser. After pressing "Continue"
Vagtacho will writes the data into immobiliser after few seconds. The dash will be reset,
and the programming procedure will be completed!
This is the last step, after this the new data will be written into immobiliser! If you have
marked and erased some keys, they will NOT works anymore!
Press "Write Keys" and the warning window will be open. If you are sure that everything is
all right, press"Continue", otherwise press "Cancel". If you press "Cancel" nothing will
happens, and the data won't be written into immobiliser. After pressing "Continue"
Vagtacho will writes the data into immobiliser after few seconds. The dash will be reset,
and the programming procedure will be completed!
This is the last step, after this the new data will be written into immobiliser! If you have
marked and erased some keys, they will NOT works anymore!
This picture shows the final Vagtacho window. If you have switched ON ignition with key
which is already programmed by TMPro, the warning lamp of immobiliser on the dash will
be turned off. The new key is already stored into immobiliser and you can start engine!
If the immobiliser's warning lamp on the dash is still flashing, there is some error in
programming procedure, you can check the transponder key - see how to do this on the
next picture!
www.anydiag.com
Skype:anydiag
MSN:myanytools@hotmail.com
Tel:008675536951880
Email:sales@anydiag.com
VAGtacho USB 5.0 support VDO with 24C32 or 24C64.
Switch ON ignition with the key which you want to test! Start software, select "VDO NEW CAN bus" from menu, and press"Transponder Check". Vagtacho will connects immobiliser.
Press "Read ECU Info" button, and wait about 10 seconds. The information about this
transponder key will be displayed on screen, see the next picture. You can press "Read
ECU Info" to testing of transponder key again. This procedure is optional, and is not
required when programming the new keys.
www.anydiag.com
Skype:anydiag
MSN:myanytools@hotmail.com
Tel:008675536951880
Email:sales@anydiag.com
VAGtacho USB 5.0 support VDO with 24C32 or 24C64.
Switch ON ignition with the key which you want to test! Start software, select "VDO NEW CAN bus" from menu, and press"Transponder Check". Vagtacho will connects immobiliser.
Press "Read ECU Info" button, and wait about 10 seconds. The information about this
transponder key will be displayed on screen, see the next picture. You can press "Read
ECU Info" to testing of transponder key again. This procedure is optional, and is not
required when programming the new keys
Transponder variable part and transponder locked must be "YES", otherwise there are
errors in programming of the new key with TMPro!
Transponder fixed part must be "YES" otherwise the key is still not programmed into
immobiliser, or Vagtacho programming procedure is not completed successfully. In case of
such error, repeat whole programming procedure again with another new transponder! All
parameters must be set "YES"!
If you need our products, please contact us by www.anydiag.com
www.anydiag.com
Skype:anydiag
MSN:myanytools@hotmail.com
Tel:008675536951880
Email:sales@anydiag.com