– Multi-Data Capture Tablet Quick Manual MetaDolce MD1800 2
Transcription
– Multi-Data Capture Tablet Quick Manual MetaDolce MD1800 2
MetaDolce MD1800 – Multi-Data Capture Tablet Quick Manual 1. Keys and Connectors 2 3 13 12 4 1 5 3 6 15 14 11 10 8&9 7 NO. Name NO. Name NO. Name 1 LCD and Touch Screen 2 Volume Up and Down 3 Power Button 4 NFC Reader Area (Front & Back) 5 1D&2D Barcode Scanner 6 Fingerprint Scanner 7 Mounting Hole 8 SIM Card Slot 9 SD Card Slot 10 USB Port / Charging Port 11 Headphone Jack 12 Front Camera 13 Speaker 14 Rear Camera 15 Flashlight MetaDolce MD1800 – Multi-Data Capture Tablet Quick Manual © MetaDolce Technologies Inc. 2014 1 2. Product Use Recommendations 2.1 Attention: Only use the charger supplied by the manufacturer to recharge the device, other chargers may cause damage. Input: 100-240V ~ 50/60 Hz Output: 5V 2000 mA 2.2 2.3 2.4 2.5 2.6 Only use the USB micro port for charging. Do not connect a charger to the USB host (Mini USB). 3. 3.1 3.2 3.3 Install and Remove SIM Card Do not disconnect the device from a PC when downloading, uploading or formatting. Do not disassemble or attempt to repair the unit or components. Do not use alcohol, thinner or benzene-chemicals to clean the surface of the device. Please back-up your files. The manufacturer is not responsible for the deletion of files after damage or repair of the device. 2.7 The device is neither waterproof nor water resistant; please keep it away from water Be sure to power off the tablet before you install or remove the SIM card. Install SIM card: Open the SIM card slot protective cover; insert the SIM card in the indicated direction. Remove SIM card: Open the SIM card slot protective cover; press the SIM card slightly with a fingertip, then the SIM card will be ejected from the slot. 4. Install and Remove SD Card 4.1 Install SD card: Open the SD card slot protective cover; insert the SD card in the indicated direction. 4.2 Remove SD card: Before removing the SD card, make sure the SD card is disconnected from the device. 4.3 Click to enter the applications list> Settings> Storage> Unmount SD card 4.4 Open the SD card slot protective cover; press the SD card slightly with a fingertip, then the SD card will be ejected from the slot. 5. Power On and Off: After the battery is charged fully and the SIM card is inserted, you can power on the device and begin use. 5.1 Power On and Unlock: Press and hold the power button until a vibration occurs. When the device turns on it will be in locked mode. To unlock the device hold and slide the icon to the icon. 5.2 Power Off: Press and hold the power button to bring up the "Device Options" dialog box, select "Power Off", then select “OK”. 5.3 Sleep Mode: You can tap the power button to turn off the screen and send the device into sleep mode. This can save battery power and extend battery life. You can also set the delay time before the screen is automatically locked. To wake up the device, press the power button again. When the device turns on it will be in locked mode. 6. Battery management and charging 6.1 Charge the battery for 8-12 hours to make sure the battery is fully charged when first used. 6.2 Insert the micro USB end of the charging cable into the micro USB slot on the device and plug the other end into a power socket. The battery charge indicator will show the battery is in the process of charging. Observe the charge indicator on your device to know when it is completely charged. 6.3 Note: In order to keep the battery working in the best condition, please pay attention to the following advice: In order to keep the battery in good condition, please make sure to charge the device once every two weeks when not in use for extended periods of time. MetaDolce MD1800 – Multi-Data Capture Tablet Quick Manual © MetaDolce Technologies Inc. 2014 2 7. Software Operation 7.1 Fingerprint Scanner (1) In the normal working state, select the [fingerprint] demo application to display the following screen: (2) Select [Open Device] to start the operation. (3) Place your finger on the sensor, then select [Continuously capture images] to capture the fingerprint image. (4) Place your finger on the sensor, then select [Continuously search] to verify the fingerprint against the captured fingerprint database. (5) Place your finger on the sensor, then select [Features comparison] to match your fingerprint. (6) Place a finger on the sensor twice, then select [Continuous entry] to enroll a fingerprint. (7) If you want to empty the captured fingerprint database, select [Clear DB] and all captured fingerprints will be removed from the device. 7.2 NFC Read/Write (1) Slide down on the scroll bar of the above [fingerprint] demo application to display the following screen: (2) Bring an RFID card into the RFID card reader area, then select [Type] to select the card type and then select [Read Card ID]; after the ID number is shown, select [Block 0] to select a block (the block 0 in sector 0 cannot be written to, only read). (3) Enter the password in the blank field beside the [Block 0] button. The default password is ffffffffffff (12 f’s). (4) Select [Verify password] to authenticate the password. MetaDolce MD1800 – Multi-Data Capture Tablet Quick Manual © MetaDolce Technologies Inc. 2014 3 (5) After password authentication, you can choose to read or write to the subsequent blocks. 7.3 1D&2D Barcode Scanner (1) In the normal working state, select the [QRcode Test] demo application. (2) Select “Send” to scan the barcode. 8. Definitions of Icons and their Functions Icon Function Icon Back to Main Menu Function Menu Current power status New peripheral device detected Current time Search Go Back Application Menu USB connected WIFI on/off Status Bar MetaDolce MD1800 – Multi-Data Capture Tablet Quick Manual © MetaDolce Technologies Inc. 2014 4