AMP-O-LECTRIC Model GII Terminating Machine Fast Facts

AMP-O-LECTRIC Model GII
Terminating Machine
Fast Facts
• Quiet operation
• Improved lighting
• Toolless changeover of
applicators
• Precision manual adjust for
crimp height
• Total and batch counter
• Accepts all existing TE applicators, with minor modifications
• Reduced maintenance
requirements
• Split-cycle operation
• Standardized 1 5/8 [41.3] stroke
• Operates on either 120 or 220
VAC, 50 or 60 Hz
The Model “G II” is the latest and most
advanced design in the long-standing
series of AMP-O-LECTRIC machines
for terminating wire using reeled terminals and contacts. It features a reliable and long lasting brush-less motor
drive. This unit is designed and built to
continue the tradition of “work-horse”
terminators from TE.
For operator convenience and
increased visibility of the work area,
we’ve improved access to, and significantly updated lighting in the under
cabinet and target area. The Crimp
Quality Monitor (CQM II) continues to
be located at eye level for bench-top
use. The Model “G II” is one of the quietest machines available, plus
improved guarding meets applicable
European and domestic safety requirements.
All Model “G II” versions include precision adjustment for crimp height — an
important feature, which, in combination with the optional CQM II, will
enable you to maintain the tight tolerances required for today’s demands
for higher levels of quality. By simply
resetting a dial, an operator can adjust
crimp height in 0.013 [.0005”] increments over a 0.457 [.018”] range.
Another user-friendly feature is its
control system. At the push of a button, you can power the motor on or
off, jog forward or reverse, switch to
split-cycle operation, turn the work
light off or on, power the air feed on
or off, or reset the batch counter. And,
it’s all reported on an LCD display. The
controls will also detect and report
errors in the machine, and stop cycling
when a bad crimp is detected by the
CQM II. The operator must then push
the reset button to continue. The
Model “G II” will accept all existing TE
miniature applicators.
AMP-O-LECTRIC Model GII Terminating Machine
Specifications and Dimensions
Part Number
2217000-1
2217000-2
2217001-1
2217001-2
2217002-1
2217002-2
AMP-O-LECTRIC
Model “GII” Machine
Versions
Description
Base unit
Base unit, with CQM II
Base unit, with stripper module
Base unit, with stripper module and CQM II
Base unit, Splice machine for end- and side-feed splice applicators
Base unit, Splice machine for end- and side-feed splice applicators, with CQM II
Specifications
Customer Manual - 409-32035
Capacity: 5000 lb [2268 kg] maximum crimp force
Air: Pneumatic 80 psi [550 KPa] for models with stripper module.
Available as an optional kit for all other models.
Electrical: 100/240 VAC, ± 10% AC, 50/60 Hz, Single phase
Dimensions (without terminal reel and reel support)
Height: 20.5 [520.7mm]
Depth: 21.5 [546.1mm]
Width: 21.8 [553.7mm]
Weight: Approx. 230 lb [104 kg]
807.88
615.78
864.88
558.94
616.44
553.59
591.58
497.66
635.22
535.65
595.80
Optional
Stripping Module
The combination of the Stripping Module with the
AMP-O-LECTRIC Model G Terminator provides an economical and proficient method of stripping wire and
crimping terminals on the same machine. Wires are
stripped moments before crimping, meaning there is virtually no chance of damaging wire conductors during
handling or storage. Once the wire is fed into the start
sensor the Stripping Module does the rest, improving
placement accuracy. Order Catalog 1309085 for more
information.
In the interest of continuous improvement, TE reserves the
right to modify, discontinue, or replace any products.
Catalog 1-1773736-1 / 05-14 / Application Tooling
AMP-O-LECTRIC, FASTON, the TE Connectivity (logo) and
TE Connectivity are trademarks.
www.tooling.te.com
TE Connectivity, Harrisburg, PA 17105, Phone: 888-777-5917 or 717-810-2080