16 G FC Compliant 850 nm SFP+ Limiting Transceiver JSH Series

16 G FC Compliant 850 nm SFP+
Limiting Transceiver
JSH Series
The JDSU 16 G 850 nm SFP+ Optical Transceiver is a full duplex,
integrated fiber optic transceiver that provides a high-speed serial link
at 14.025 Gbps signaling rates. The transceiver supports the enhanced
small form factor pluggable module (SFP+) specification SFF-8431
Rev. 4.1 for the low-speed electrical interface, SFF-8432 Rev. 5.0 for the
mechanical interface, and SFF-8472 Rev. 11.0 for the management
interface.
Key Features
The transceiver complies with the Fibre Channel FC-PI-5 1600-M5x-SN variants, and complies
with 800-M5x-SN and 400-M5x-SN-I when using rate-select inputs.
• Linear SFI AC-coupled electrical output interface
It integrates the receive and transmit path on one module. On the transmit side, the
14.025 Gbps serial data stream is passed from the electrical connector and recovered and
retimed through a CDR to a laser driver. The laser driver biases and modulates an 850 nm
vertical cavity surface-emitting laser (VCSEL), enabling data transmission over up to
125 m of OM4 multimode fiber through an industry-standard LC connector. On the receive
side, the 14.025 Gbps optical data stream is recovered from a PIN photodetector through
a transimpedance amplifier, post amplifier and CDR, and passed to an output driver. This
module features a hot-pluggable SFI-compliant limiting electrical interface. It has an
enhanced digital diagnostic feature set to monitor real-time transceiver performance. It also
has transmit disable, loss of signal, and transmitter fault functions.
• 16 G Fibre Channel (FC) specification compliant
• 8 G and 4 G FC specification compliant under
rate-select control
• 850 nm VCSEL laser
• Up to 125 m reach over OM4 multimode fiber
• Operating temperature range of 0 to 70°C
• Maximum power dissipation of 1 W
• Single 3.3 V power supply
• Supports digital diagnostic monitoring
Applications
• Storage area networks (SAN)
–– FC switches and hubs
–– Host bus adapters
–– Network interface cards (NICs)
–– Mass storage system
• Computer cluster cross-connects
Compliance
• FC-PI-5 Fibre Channel standard
• SFF-8431 Rev 4.1
• SFF-8432 Rev 5.0
• SFF-8472 Rev 11.0
• Class 1 laser safety
• Tested in accordance with Telcordia GR-468
• RoHS 6/6
www.jdsu.com
Data Sheet
16 G FC Compliant 850 nm SFP+ Limiting Transceiver — JSH Series
Section 1 Functional Description
The 16 G 850 nm SW SFP+ optical transceiver is a full duplex serial electric,
serial optical device with both transmit and receive functions contained
in a single module that provides a high-speed serial link at 14.025 Gbps
signaling rates. The transceiver complies with Fibre Channel FC-PI-5
1600-M5x-SN variants when the rate-select inputs are pulled high, and
complies with 800-M5x-SN and 400-M5x-SN-I when the rate-select
inputs are pulled low. The transceiver supports the Enhanced Small Form
Factor Pluggable Module SFP+ specification SFF-8431 Rev. 4.1 for the
electrical interface, SFF-8432 Rev. 5.0 for the mechanical interface, and
SFF-8472 Rev. 11.0 for the management interface. Figure 1 shows a block
diagram.
VCCT
VEET
VCCR
VEER
Receiver
ROSA
The receiver converts incoming DC-balanced serial NRZ 4.25 to
14.025 Gbps line rate optical data into serial electrical signals. The
amplified signal is passed to a signal conditioning IC that provides
clock and data recovery. The receive CDR function generates a clock
that is at the same frequency as the incoming data bit rate of the
optical data input. The clock is phase aligned by a PLL that samples
the data in the center of the data eye pattern. The CDR contains a lock
detect circuit that indicates successful locking of the PLL onto the
incoming data.
RD–
CDR
TIA
SCL
MCU
SDA
TD–
Laser
Driver
CDR
TD+
The amplified signal is output directly on the RD+ and RD− pins as a
100 Ω CML signal.
TOSA
RX_LOS
TX_FAULT
VEET
VEET
VEET
VCCT
Low-Speed Signaling
TX_DIS
RS0
RS1
The Tx signal conditioner’s output is input to the laser driver circuit which
transforms the small swing digital voltage to an output modulation that
drives a VCSEL laser. The optical signal is engineered to meet the 16 G FC
when the rate-select inputs are pulled high and 8 G and 4 G FC specifications when the rate-select inputs are pulled low. Closed-loop control
of the transmitted laser power over temperature and voltage variations
is provided. The laser is coupled to a multimode optical fiber through an
industry-standard LC optical connector.
Transceiver Ground
Power Supply Sequence/
In-Rush Control Circuit
RD+
Inside the module, the differential signal passes through a signal conditioner with equalization that compensates for input data stream losses
and deterministic jitter. The transmit CDR function generates a clock that
matches the incoming data bit rate frequency of the electrical data input.
The clock is phase aligned by a phase locked loop (PLL) that samples the
data in the center of the data eye pattern.
MOD_ABS
Figure 1. JDSU SFP+ optical transceiver functional block diagram
Low-speed signaling is based on low-voltage TTL (LVTTL) operating at a
nominal voltage of 3.3 V. Hosts should use a pull-up resistor connected
to VCC 3.3 V on the 2-wire interface SCL, SDA, and all low-speed outputs
based on the SFF 8431 Rev. 4.1 requirements.
The transceiver has several low-speed interface connections. These
connections include: transmitter fault (Tx_Fault), transmitter disable
(Tx_Disable), rate select (RS0 and RS1), module absent (Mod_ABS),
receive loss of signal (Rx_LOS), and a 2-wire serial interface clock (SCL)
and data (SDA).
Low-Speed Interface
Connections
Definition
SCL/SDA
2-wire serial interface clock and data line.
Tx_Fault
Output pin. When asserted high, indicates that the
module has detected a transmitter fault condition
related to laser operation or safety.
The transceiver supports the SFI electrical interface. The electrical
interface is based on a high-speed, low-voltage logic AC-coupled
limiting interface with a 100 Ω nominal differential impedance.
Tx_Disable
Input pin. When asserted high or left open, the
transmitter output is turned off. When Tx_Disable is
asserted low or grounded, the module transmitter is
operating normally.
Transmitter
RS0 and RS1
Input pins. Pulled low to VEET with > 30 kΩ resistors in
the module. When RS1 is asserted low, the transmitter
CDR is bypassed and the module transmitter is
optimized for low-speed operation, 8.5 Gbps or
lower. When RS0 is asserted low, the receiver CDR is
bypassed and the module receiver is optimized for
low-speed operation, 8.5 Gbps or lower.
Mod_ABS
Output pin. Asserted high when the SFP+ module is
absent and is pulled low when the SFP+ module is
inserted.
Rx_LOS
Output pin. Asserted high when insufficient optical
power for reliable signal reception is received.
The transmitter path converts serial NRZ electrical data from 4.25
to 14.025 Gbps line rates to a standard compliant optical signal. The
transmitter accepts a 100 Ω differential 180 mV peak-to-peak to 700 mV
peak-to-peak CML electrical signal on TD– and TD+ pins.
www.jdsu.com
2
16 G FC Compliant 850 nm SFP+ Limiting Transceiver — JSH Series
3.1 Rx_LOS
Mod_ABS
Tx_Fault
OUTPUT
Tx_Disable
RS1
2
RS0
SCL/SDA
INPUT
GND VEER
GND VEET
+3.3 V VCCR
+3.3 V VCCT
POWER
Toward ASIC
SFP+ modules are hot pluggable and active connections are powered
by individual power connections for the transmitter (VCCT) and the
receiver (VCCR). Multiple modules can share a single 3.3 V power supply
with individual filtering for each VCCT and VCCR. The host shall generate
an effective weighted integrated spectrum RMS noise of less than
25 mV in the 10 Hz to 10 MHz frequency range. Detailed power supply
specifications are given in SFF-8431 Rev. 4.1 Section 2.8. Figure 2
shows recommended MSA connections to the JDSU 16 G SFP+ optical
transceiver.
Pin Function Definitions
11
VEER
12
RD–
13
RD+
14
VEER
15
VCCR
16
VCCT
17
VEET
18
TD+
19
TD–
20
VEET
VEER
10
RS1
9
Rx_LOS
8
RS0
7
MOD_ABS
SCL
6
SDA
4
Tx_Disable
3
Tx_Fault
2
VEET
1
5
Toward Bezel
Section 2 Application Schematics
Figure 3. 16 G SFP+ optical transceiver host board pin assignments
2
2
TD +/−
SFP+ Module
RD +/−
Table 1. 16 G SFP+ optical transceiver pin descriptions
Pin No. Type
1
Figure 2. JDSU 16 G SFP+ optical transceiver application schematic
Section 3 Name
Description
VEET1
Module transmitter ground
2
LVTTL-O
Tx_Fault2
Module transmitter fault; logic 1 indicates
laser fault.
3
LVTTL-I
Tx_Disable
Transmitter disable; when asserted high
or left open, transmitter laser source
turned off.
4
LVTTLI/O
SDA2
2-wire interface data line
5
LVTTL-I
SCL2
2-wire interface clock
Mod_ABS2
Indicates module is not present.
Grounded to VEET or VEER in the module.
Technical Specifications
Section 3.1 Pin Function Definitions
Section 3.2 SFP+ SFI Reference Model Compliance Points
Section 3.3 Absolute Maximum Ratings
Section 3.4 Operating Conditions
Section 3.5 Electrical Characteristics
Section 3.6Electrical Jitter Specifications
Section 3.7 Timing Requirement of Control and Status I/O
Section 3.8
SFP+ 2-Wire Interface Protocol and Management Interface
Section 3.9
Optical Transmitter Characteristics
Section 3.10 Optical Eye Mask
6
7
LVTTL-I
RS0
Rate select 0; logic low indicates an
8.5 Gbps receiver signal rate or lower
8
LVTTL-O
Rx_LOS2
Receiver loss of signal
9
LVTTL-I
RS1
Rate select 1; logic low indicates an
8.5 Gbps transmitter signal rate or lower
10
VEER1
Module receiver ground
11
VEER1
Module receiver ground
12
CML-O
RD−
Receiver inverted data output
13
CML-O
RD+
Receiver non-inverted data output
14
Module receiver ground
Section 3.13 Optical Characteristics Comparison at 8 G FC and 4 G FC
VEER1
15
VCCR
Module receiver +3.3 V supply
Section 3.14 Regulatory Compliance
16
VCCT
Module transmitter +3.3 V supply
Section 3.15 PCB Layout
17
VEET1
Module transmitter ground
Section 3.16 Module Outline
18
CML-I
TD+
Transmitter non-inverted data input
19
CML-I
TD−
Transmitter inverted data input
VEET
Module transmitter ground
Section 3.11 Multimode Fiber Reaches
Section 3.12 Optical Receiver Characteristics
Section 3.17 Connectors
20
1
1. Module ground pins (GND) are isolated from the module case and chassis ground within the module
2. Shall be pulled up with 4.7 to 10 kΩ to a voltage between 3.15 V and 3.45 V on the host board
www.jdsu.com
3
16 G FC Compliant 850 nm SFP+ Limiting Transceiver — JSH Series
3.2 16 G SFP+ SFI Reference Model Compliance Points
C'
C
Rx
Connector
D
ASIC/
SERDES
A
B'
SFP+ Module
Tx
B
Figure 4. SFP+ optical transceiver model compliance points
3.3 Absolute Maximum Ratings
Absolute maximum ratings represent the device's damage thresholds. Permanent damage may occur if the device is stressed beyond the limits stated here.
Performance is not guaranteed and reliability is not implied for operation at any condition outside the recommended operating limits.
Parameter
Storage temperature
Operating case temperature
Relative humidity
Static electrical discharge (human body model)
Symbol
TST
TOP
RH
ESD
Power supply voltages
Receive input optical power (damage threshold)
VCCT, VCCR, max
Pdth
3.4
Ratings
−40 to +85
0 to +70
5 to 85 (noncondensing)
1000 (high-speed lines)
2000 (low-speed lines)
−0.3 to 4.0
+3
Unit
°C
°C
%
V
V
dBm
Operating Conditions
Performance is not guaranteed and reliability is not implied for operation at any condition outside the operating limits.
Parameter
Operating case temperature rating
3.5 Min
0
Max
+70
Unit
°C
Electrical Characteristics
Parameter
Supply Currents and Voltages
Voltage
Supply current
Power dissipation
Symbol
Min.
Typ.
Max.
Unit
Notes
VCC
3.14
3.3
3.47
290
1.0
V
mA
W
With respect to GND
0.4
37.5
0.8
V
μA
V
At 0.7 mA
Measured with a 4.7 kΩ load pulled up to VCC_host
TX_Disable is pulled up in module to VCCT with
10 kΩ
RS0 and RS1 are pulled down to VEET in module
with >30 kΩ
Pwr
Low-Speed Control and Sense Signals (detailed specification in SFP+ MSA SFF-8431 Rev. 4.1)
−0.3
Outputs (Tx_Fault, Rx_LOS)
VOL
−50
IOH
−0.3
Inputs (Tx_Disable, RS0, RS1)
VIL
SCL and SDA inputs
www.jdsu.com
VIH
2
VCC3+0.3
V
VIL
VIH
−0.3
VCC3*0.7
VCC3*0.3
VCC3+0.5
V
V
Rpullup pulled to VCC_host
4
16 G FC Compliant 850 nm SFP+ Limiting Transceiver — JSH Series
3.6
Electrical Jitter Specifications
Parameter
Symbol
Min.
Max.
Unit
Notes
Transmitter Electrical Input Signal Tolerance from Host at B” (detailed specification in FC-PI-5 Rev 6.1, FC-MJSQ, and FC-MSQS)
Independent deterministic jitter
DJ
0.31
UI(p-p)
JSPAT pattern, BER < 1x10-12, at 14.025 Gbps
Input data-dependent pulse-width shrinkage
DDPWS
0.11
UI(p-p)
Uncorrelated jitter
UJ
0.03
UI(rms)
See FC-MSQS
JSPAT pattern, BER < 1x10-12, at 14.025 Gbps
Total input jitter
TJ
0.45
UI(p-p)
Eye mask
X1
0.03
UI
X2
0.045
UI
Reference FC-PI-5
Y1
90
0.225
mV
Y2
350
mV
Receiver Electrical Output Signal to Host at C’ (detailed specification in FC-PI-5 Rev 6.1, FC-MJSQ, and FC-MSQS)
Output deterministic jitter
DJ
0.22
UI(p-p)
JSPAT pattern, BER < 1x10-12, at 14.025 Gbps
Output data dependent pulse-width shrinkage
DDPWS
0.14
UI(p-p)
Total jitter
TJ
0.70
UI
Eye mask
X1
0.18
UI
X2
0.5
UI
850
mV
Differential peak-to-peak voltage
3.7
Vp-p
340
Reference FC-PI-5
Timing Requirement of Control and Status I/O
Parameter
Max.
Unit
Tx_Disable assert time
Symbol
t_off
100
µs
Rising edge of Tx_Disable to fall of output signal
below 10% of nominal
Tx_Disable negate time
t_on
50
ms
Falling edge of Tx_Disable to rise of output
signal above 90% of nominal1
t_2w_start_up
300
ms
t_start_up_cooled
90
s
50
ms
From occurrence of fault to assertion of Tx_Fault
µs
Time Tx_Disable must be held high to reset
Tx_Fault
Time to initialize 2-wire interface
Time to initialize
Tx_Fault assert
Tx_Fault_on _cooled
Tx_Fault reset
Tx_Fault_reset
Min.
10
Notes
From power on or hot plug
Rx_LOS assert delay
t_loss_on
100
µs
From occurrence of loss of signal to assertion
of Rx_LOS
RX_LOS negate delay
t_loss_off
100
µs
From occurrence of return of signal to negation
of RX_LOS
1. The transceiver is thermally stabilized prior to Tx_Disable negating event.
3.8
2-Wire Interface Protocol and Management Interface
The JDSU SFP+ optical transceiver incorporates a 2-wire management interface, compliant with the SFF-8472 Rev 11.0 specification, which is used for
serial ID, digital diagnostics, and certain control functions.
Rate Identifier (user ID address A0h, Byte 13) is used to control the independent Tx and Rx Rate Select function through software. The timing and
functionality is defined in the SFF-8472 Rev 11.0 specification.
The MSA explicitly describes the details of the protocol and interface. Please refer to the MSA for design reference.
www.jdsu.com
5
16 G FC Compliant 850 nm SFP+ Limiting Transceiver — JSH Series
3.9 Optical Transmitter Characteristics1
Parameter
Average optical power2
Optical modulation amplitude (OMA)3
Extinction ratio (informative)
Center wavelength
RMS spectral width2
Vertical eye closure penalty
Relative intensity noise
Symbol
Pavg
OMA
ER
λ
Min.
–7.8
–4.8
3.85
840
Typ.
860
0.59
2.56
–128
Unit
dBm
dBm
dB
nm
nm
dB
dB/Hz
Min.
Typ.
Max.
Unit
0.25
0.40
0.45
0.32
0.35
0.40
UI
UI
UI
dBm
dB
nm
nm
dB
dB/Hz
VECP
RIN12OMA
Max.
–1.0
3.10 Optical Eye Mask
Parameter
Transmitter optical output
Eye mask4
Symbol
X1
X2
X3
Y1
Y2
Y3
1. These specifications are applicable within the operating case temperature range specified in Section 3.4.
2. For 16 G FC operation when RS1 is high
3. Tested with PRBS 231 – 1 pattern
4. Reference FC-PI-5
Figure 5. 16 G SFP+ optical transmitter eye mask
www.jdsu.com
6
16 G FC Compliant 850 nm SFP+ Limiting Transceiver — JSH Series
3.11 Multimode Fiber Reaches
Data Rate (Mbps)
1600
800
400
Fiber Type
Variant Name
Reach (m)
Line Budget (dB)
Overfilled Modal Bandwidth –
Length at 850 nm (MHz*km)
OM2
1600-M5-SN-S
0.5 – 35
1.63
500
OM3
1600-M5E-SN-I
0.5 – 100
1.86
1500
OM4
1600-M5F-SN-I
0.5 – 125
1.95
3500
OM2
800-M5-SN-S
0.5 – 50
1.68
500
OM3
800-M5E-SN-I
0.5 – 150
2.04
1500
OM4
800-M5F-SN-I
0.5 – 190
2.19
3500
OM2
400-M5-SN-I
0.5 – 150
2.06
500
OM3
400-M5E-SN-I
0.5 – 380
2.88
1500
OM4
400-M5F-SN-I
0.5 - 400
2.95
3500
3.12 Optical Receiver Characteristics1
Parameter
Symbol
Min.
λ
840
Center wavelength
Typ.
Max.
Unit
860
nm
Unstressed receiver sensitivity (OMA)
–10.5
dBm
Stressed jitter tolerance test (OMA)2
–6.7
dBm
Stressed receiver sensitivity (OMA)
–7.7
Receive overload2
dBm
Pmax
0
12
dB
LOS assert
Plos_on
–31
dBm
LOS deassert
Plos_off
Return loss
LOS hysteresis
dBm
0.5
–11
dBm
4
dB
3.13 Optical Characteristics Comparison at 8 G FC and 4 G FC
Parameter
Unit
1600-SN
Min.
Max.
Average optical power
dBm
–7.8
Optical modulation amplitude
dBm
–4.8
–1.0
Min.
–8.2
800-SN
Max.
–1.0
–5.2
Min.
–9.0
400-SN
Max.
–1.0
–6.1
RMS spectral width
nm
0.59
0.65
0.65
Unstressed receiver sensitivity (OMA)
dBm
–10.5
–11.2
–12.1
Rx jitter tolerance (OMA)
dBm
–6.7
–7.0
–8.1
Stressed receiver sensitivity
dBm
–7.7
–8.2
–8.6
1. These specifications are applicable within the operating case temperature range specified in Section 3.4.
2. Guaranteed at 14.025 Gbps; measured with worst ER; BER<10-12; PRBS 231 – 1 pattern
www.jdsu.com
7
16 G FC Compliant 850 nm SFP+ Limiting Transceiver — JSH Series
3.14 Regulatory Compliance
The transceiver complies with international safety and electromagnetic compatibility (EMC) requirements and standards. EMC performance
depends on the overall system design. The transceiver uses lead-free solder and is RoHS 6/6 compliant.
Table 2. Regulatory Compliance
Feature
Test Method
Performance
Safety
Product
UL 60950-1
CSA C22.2 No. 60950-1
Laser
UL recognized component for US and CAN
EN 60950-1
TUV certificate
IEC 60950-1
CB certificate
Flame class V-0
Passes needle point flame test for component flammability verification
Low Voltage Directive 2006/95/EC
Certified to harmonized standards listed; Declaration of Conformity issued
EN 60825-1, EN 60825-2
TUV certificate
IEC 60825-1
CB certificate
U.S. 21 CFR 1040.10
FDA/CDRH certified with accession number
Electromagnetic Compatibility
Radiated
emissions
EMC Directive 2004/108/EC
FCC rules 47 CFR Part 15
CISPR 22
AS/NZS CISPR22
EN 55022
ICES-003, Issue 5
Class B digital device with a minimum −2 dB margin to the limit. Final margin may vary depending
on system implementation.
Tested frequency range: 30 MHz to 40 GHz or 5th harmonic (5 times the highest frequency),
whichever is less.
Requires good system EMI design practice to achieve Class B margins at the system level.
VCCI regulations
Immunity
EMC Directive 2004/108/EC
CISPR 24
Certified to harmonized standards listed; Declaration of Conformity issued.
EN 55024
ESD
IEC/EN 61000-4-2
Exceeds requirements. Withstands discharges of ± 8 k V contact, ±15 k V air.
Radiated
immunity
IEC/EN 61000-4-3
Exceeds requirements. Field strength of 10 V/m from 80 MHz to 6 GHz.
No detectable effect on transmitter/receiver performance between these limits.
Restriction of Hazardous Substances (RoHS)
RoHS
EU Directive 2011/65/EU
Compliant per the European Parliament Directive 2011/65/EU of the 8 June 2011 on the
restricted use of certain hazardous substances in electrical and electronic equipment (recast).
An RoHS Certificate of Conformance (C of C) is available upon request.
The product may use certain RoHS exemptions.
3.15 PCB Layout
Recommended PCB layout is given in SFP+ MSA SFF8431 Rev. 4.1.
www.jdsu.com
8
16 G FC Compliant 850 nm SFP+ Limiting Transceiver — JSH Series
3.16 Module Outline
3.17Connectors
Fiber
The SFP+ module has a duplex LC receptacle connector.
Electrical
The electrical connector is a 20-way, two-row PCB edge connector. The customer connector is Tyco/AMP Part No. 188247 or equivalent.
www.jdsu.com
9
16 G FC Compliant 850 nm SFP+ Limiting Transceiver — JSH Series
Section 4 Other Related Information
Test and Operation
Section 4.1 Packing and Handling Instructions
Section 4.2 Electrostatic Discharge
Section 4.3 Laser Safety
In most applications, the optical connector will protrude through the
system chassis and be subjected to the same ESD environment as the
system. Once properly installed in the system, this transceiver should
meet and exceed common ESD testing practices and fulfill system ESD
requirements.
4.1 Package and Handling Instructions
Connector Covers
The transceiver is supplied with an LC duplex receptacle. The connector
plug supplied protects the connector during standard manufacturing
processes and handling by preventing contamination from dust,
aqueous solutions, body oils, or airborne particles.
Note: It is recommended that the connector plug remain on whenever
the transceiver optical fiber connector is not inserted.
Recommended Cleaning and Degreasing Chemicals
JDSU recommends the use of methyl, isopropyl, and isobutyl alcohols
for cleaning.
Do not use halogenated hydrocarbons, such as trichloroethane or
ketones such as acetone, chloroform, ethyl acetate, MEK, methylene
chloride, methylene dichloride, phenol, and N-methylpyrrolidone.
Typical of optical transceivers, this module’s receiver contains a
highly sensitive optical detector and amplifier which may become
temporarily saturated during an ESD strike. This could result in a short
burst of bit errors. Such an event might require that the application
re-acquire synchronization at the higher layers (for example, a
serializer/deserializer chip).
4.3 Laser Safety
The transceiver is certified as a Class 1 laser product per international
standard IEC 60825-1:2007 2nd edition and is considered nonhazardous when operated within the limits of this specification.
The transceiver complies with 21 CFR 1040.10 except for deviations
pursuant to Laser Notice No. 50 dated June 24, 2007.
This product is not designed for aqueous wash.
Housing
The transceiver housing is made from zinc.
4.2 Caution
Electrostatic Discharge
Operating this product in a manner inconsistent with intended usage
and specifications may result in hazardous radiation exposure.
Handling
Normal electrostatic discharge (ESD) precautions are required
during the handling of this module. This transceiver is shipped in ESD
protective packaging. It should be removed from the packaging and
otherwise handled in an ESD protected environment utilizing standard
grounded benches, floor mats, and wrist straps.
Use of controls or adjustments or performance of procedures other
than these specified in this product data sheet may result in hazardous
radiation exposure.
Tampering with this laser product or operating this product outside the
limits of this specification may be considered an ‘act of manufacturing’
and may require recertification of the modified product.
Ordering Information
For more information on this or other products and their availability,
please contact your local JDSU account manager or JDSU directly
at 1-800-498-JDSU (5378) in North America and +800-5378-JDSU
worldwide or via e-mail at customer.service@jdsu.com.
North America Worldwide
www.jdsu.com
Description
Product Code
16 G FC, 125 m reach, limiting, 850 nm,
commercial temperature range, SFP+ optical
transceiver
JSH-14SWAA1
Toll Free: 800 498-JDSU (5378)
Tel: +800 5378-JDSU
© 2014 JDS Uniphase Corporation Product specifications and descriptions in this document are subject to change without notice.
30175996 000 1014 JSH-14SWAA1.DS.OC.AE October 2014