XTC-3D® High Performance 3D Print Coating PRODUCT OVERVIEW

XTC-3D®
High Performance 3D Print Coating
www.smooth-on.com
PRODUCT OVERVIEW
XTC-3D® is a protective coating for smoothing and finishing 3D printed parts. Two liquids are mixed together and
brushed onto any 3D print. Coating self-levels and wets out uniformly without leaving brush strokes. Working time is 10
minutes and cure time is about 4 hours (depending on mass and temperature). XTC-3D® cures to a hard, impact resistant
coating that can be sanded, primed and painted. Adding colors and metal effects is easy.
Inexpensive to Use – 1 oz covers 100+ square inches (see coverage information below).
90% Time & Labor Savings: XTC-3D® fills in 3D print striations and creates a smooth, high gloss finish. The need to post
finish is almost eliminated.
Coat any 3D Print Surface - XTC-3D® can be applied to both SLA and SLS prints. It works with PLA, ABS, Laywoo, Powder
Printed Parts and other rigid media. It also can be used to coat EPS, EPDM and urethane foam as well as wood, plaster, fabric,
cardboard and paper.
XTC-3D® does not contain VOC’s, phthalates or phosphates.
PROCESSING RECOMMENDATIONS
Material Properties
Mix Ratio By Volume
2A : 1B
Mix Ratio By Weight
100A : 42B
Mixed Viscosity - CPS. (ASTM D2393)
350
Specific Gravity - Mixed; g./c.c. (ASTM D1475)
1.09
Spec. Volume - Mixed; cu. in./lb. (ASTM D792)
25.1
Preparation – Materials should be stored and used in a room
temperature environment (73°F/23°C). Elevated temperatures will reduce
Pot Life. XTC-3D® Part A resin and Part B Hardener must be properly
measured and thoroughly mixed to achieve full, high-strength, solid-cure
properties. Because no two applications are quite the same, a small test
application to determine suitability for your project is recommended if
performance of this material is in question.
Pot Life In Mass - (ASTM D2471)*
10 minutes
Pot Life In Flat Tray (Reduced Mass)
15 Minutes
Thin Film Working Time
20 minutes
Thin Film Tacky Recoat Time
90 minutes
Avoid eye and skin contact. Avoid breathing fumes - use in a well ventilated
area. NIOSH approved respirator is recommended. Wear safety glasses,
long sleeves and rubber gloves to minimize skin contact. This material
has a high exotherm (generates heat). Do not mix components in glass
or foam containers.
Thin Film Tack Free Time
2 hours
Coverage – A very small amount of XTC-3D® is needed to coat an
Cure Time In Mass (100 g)
2 hours
Cure Time In Thin Layer
3.5 hours
Color In Thin Layer
Clear
Shore D Hardness (ASTM D2240)**
80D
(Slightly Yellow In Thick Sections)
* Dependant on mass
** Value measured after 7 days at 73°F / 23°C
average size 3D print. 1 oz / 28.3 grams of mixed material will cover 101
in2 (651 cm2) applied at 1/64” (.04 cm) thickness.
Pre-Mix Part B: Before using, shake container vigorously.
Measuring and Dispensing – You need to be accurate in measuring
for XTC-3D® to cure properly. Parts A and B can be measured by either
volume or weight. Dispense proper proportions of parts A and B into
clean plastic, metal or wax-free paper containers (do not use foam or
glass cups).
Extending Working Time - If left in a mixing cup with a concentrated mass, pot life will be short and material may cure in
your cup due to exotherm. Important - Reduce the mass of the mixture to increase working time. Example: layer two sheets of
aluminum foil together and create a single-use flat tray with vertical sides to contain the liquid resin. After mixing parts A and B,
pour mixture into the aluminum foil to reduce the mass. Your working time will be significantly increased.
Mixing – Be sure mixing utensils have a square edge and are clean. Combine and mix proper amounts of Parts A and B. Mix
thoroughly for at least 1 minute. Aggressively scrape the sides and bottom of mixing container several times. Use the square edge
of mixing stick to bring material off of the sides and bottom of container and blend.
Important - Mixed XTC-3D® Resin is exothermic, meaning it generates heat. A large, concentrated mass of mixed material in
a container can generate enough heat to melt a plastic cup, burn your skin or ignite combustible materials. If material begins
to exotherm, move it to an open air environment.
Adding Color - XTC-3D® can be colored with SO Strong® color tints,
UVO® color pigments or ignite color pigments. Pre-mix color with Part A
before combining with Part B.
Safety First!
The material safety data sheet (MSDS) for this or any
Smooth-On product should be read before using
and is available on request. All Smooth-On products
are safe to use if directions are read and followed
carefully.
XTC-3D® Resin PART A:
WARNING: IRRITANT TO EYES, SKIN & MUCOUS
MEMBRANES.
XTC-3D® Resin is irritating to the eyes and skin.
Avoid prolonged or repeated skin contact to prevent
possible sensitization. Avoid breathing vapors and
use only with adequate ventilation. Wear personal
protective equipment.
First Aid: In case of eye contact, flush thoroughly
with water for 15 minutes and get immediate
medical attention. In case of skin contact, wipe
clean with white vinegar and wash thoroughly with
soap and water. If irritation persists, get medical
attention. If swallowed, do not induce vomiting.
Drink 1 - 2 glasses of water and get immediate
medical attention.If vapors are inhaled or if breathing
becomes difficult, remove person to fresh air.
If symptoms persist, get medical attention.
Adding Fillers - A variety of dry fillers can be added such as Cast
Magic® or bronze or other metal powders, Glow Worm®, Quarry Tone®
or Ure-Fil® powders. The maximum filler load is an amount equal to Part
A by volume. Pre-mix filler with Part A before combining with Part B.
Applying XTC-3D® - Use a disposable chip brush or foam brush
to apply XTC-3D®. To achieve the thinnest coating possible we
recommend applying XTC-3D® with a foam brush. Brushing on one
thin layer of mixed material is recommended for most prints to create a
smooth, uniform coating: less than 1/64“(.039 cm). To avoid drips and
runs, continue brushing and working the surface until the resin begins
to set up. For particularly complicated prints with intricate detail you
may want to coat one a section at a time for better control. XTC-3D®
bonds to itself.
If Adding More Layers - allow first layer to partially cure until
“tacky hard” before applying the next layer. For best results, each layer
should be applied thinly: less than 1/64“(.039 cm).
Thinning XTC-3D® - If you want to lower the mixed viscosity,
Keep Out Of Reach Of Children.
you can add denatured alcohol. Mix 2A:1B by volume and add ½ part
denatured alcohol.
XTC-3D® PART B Hardener:
Curing: One layer will cure tack free in about 2 hours at room
WARNING: IRRITANT TO EYES, SKIN & MUCOUS
MEMBRANES.
Epoxy Hardeners are corrosive materials and can
cause severe eye and skin burns. They are sensitizers
that may cause dermatitis from skin contact or vapor
inhalation. Use these products only with adequate
ventilation. Remove contaminated clothing and
wash from skin with soap and water.
First Aid: In case of eye contact, flush thoroughly
with water for 15 minutes and get immediate medical
attention.
Keep Out Of Reach Of Children.
IMPORTANT: The information contained in this
bulletin is considered accurate. However, no warranty
is expressed or implied regarding the accuracy of the
data, the results to be obtained from the use thereof,
or that any such use will not infringe upon a patent.
User shall determine the suitability of the product
for the intended application and assume all risk and
liability whatsoever in connection therewith.
temperature (73°F/23°C). Mild heat (150° F/60° C) will cure material
within 15 minutes. Be careful: some 3D print media will melt at
temperatures above 200°F. Fully cured material will be hard and unable
to penetrate with a finger nail.
Post Finishing – Cured material can be machined or sanded (wear
NIOSH approved respirator mask to prevent inhalation).
Painting – XTC-3D® can be painted and/or primed and then painted
with acrylic enamel paints. For best results, lightly sand surface prior to
painting.
Removing Uncured Material: Scrape as much material as
possible from the surface using a scraper. Clean the residue with
E-POX-EE KLEENER® available from Smooth-On, lacquer thinner, acetone
or alcohol. Follow safety warnings pertaining to solvents and provide
adequate ventilation.
Call Us Anytime With Questions About Your Application
Toll-free: (800) 381-1733 Fax: (610) 252-6200
The new www.smooth-on.com is loaded with information about mold making, casting and more.
101714-JR