MediaPort 7000 Series Quick Reference Guide

MediaPort 7000 Series Quick Reference Guide
MediaPort Chassis (MPC-7002) Bezel
Port Status Display
Air Vents
Power Indicator
NOTE: Alarms will cause the display to flash.
To stop flashing, resolve the alarm or touch the display.
The Port Status Display allows you to enable the display
of a static color bar pattern on any or all of the SDI Output
connectors, which can be used to verify connectivity.
For more details, refer to “MediaPort 7000 Series Front Panel”
in the Spectrum Installation and Hardware Reference Guide.
Status
of
Module A
Status
of
Module B
Port Status Display
Health Summary
Reference Input
Channel 0: Player name, Player state, and mecode
Channel 1: Player name, Player state, and mecode
Environmental alarms, if any
Health Summary
Reference Input
Channel 0: Player name, Player state, and mecode
Channel 1: Player name, Player state, and mecode
Environmental alarms, if any
MediaPort Chassis Rear Panel
Power Supplies and LEDs
PS 0
PS 1
Module A
Filler Panels
Module B
Power Supply LED States
Off: No AC power to both units
Green (blink): AC power present, unit on standby
Green (solid): Power supply on and OK
Red (blink): No AC power to this unit only
Red (solid): Power supply failure
NOTE: When a power supply fails, an audible alarm sounds.
GPIO/Signal Assignments
The MediaPort 7000 module has a female GPIO connector that can
be connected to an external device and used to control players.
For information on configuring GPIO using SystemManager, refer to
“MediaPort Configuration” in the Omneon SystemManager User Guide.
9
8 7 6 5 4 3 2 1
18 17 16 15 14 13 12 11 10
26 25 24 23 22 21 20 19
GPIO Signals
Function
Pin
Ground
GPIO 0
GPIO 1
GPIO 2
GPIO 3
GPIO 4
GPIO 5
GPIO 6
GPIO 7
18
19
20
21
22
23
24
25
26
Harmonic Technical Support: +888 673 4896 (Americas), +65 6542 0050 (Asia Pacific), + 44 1252 555 450 (EMEA),
+7 495 926 4608 (Russia, CIS), +81 3 5565 6737 (Japan), +86 10 8391 3313 (China, mainland)
28-0339 Rev. E
MediaPort Modules 7000 Series Rear Panel
Unused
13
1
2
3
4
6
5
15
RS-422 Port LEDs
14
Activity
Activity
Ethernet Port LEDs
Activity
7
1.
2.
3.
4.
5.
6.
8
10
9
11
16 17
12
HD/SD SDI IN Channel A
HD/SD SDI OUT Channel A (Primary)
HD/SD SDI OUT Channel A (Secondary)
HD/SD SDI IN Channel B
HD/SD SDI OUT Channel B (Primary)
HD/SD SDI OUT Channel B (Secondary)
7.
8.
9.
10.
11.
12.
Status
18
LTC IN Channel A
LTC OUT Channel A
LTC IN Channel B
LTC OUT Channel B
Reference IN
Reference Loop
13.
14.
15.
16.
17.
18.
Soft Power button (middle)
Status/Wink LED (bottom)
GPIO/RS-422 connector
RS-422 Port
Service Use Only
Ethernet/MediaDirector
Installing a MediaPort Module
To install a MediaPort module:
Caution: Do not use the two lock screws on the rear
1. If you are installing two modules, you may need to
panel of the module to pull it into position. Tighten the
screws only after the module is fully inserted.
first remove a filler panel from the chassis. From the
rear of the MediaPort, unscrew the two lock screws
that secure the filler panel, and then remove the filler panel.
2
1
2. Grasp the module handle and push firmly into the
slot. Ensure the module is fully inserted by pressing
on the connectors with the palm of your hand.
3. Tighten the two lock screws on the rear of the module
to secure it to the chassis.
3
4. If installing two modules, repeat steps 1-3 for the
second module.
For complete replacement instructions, refer to the Spectrum Component Replacement Guide.
Harmonic Technical Support: +888 673 4896 (Americas), +65 6542 0050 (Asia Pacific), + 44 1252 555 450 (EMEA),
+7 495 926 4608 (Russia, CIS), +81 3 5565 6737 (Japan), +86 10 8391 3313 (China, mainland)
28-0339 Rev. E
Replacing a MediaPort Chassis Power Supply
To remove a power supply:
1. Disconnect the AC power cable.
2. Press the release lever to the right and pull
the handle to remove the power supply.
To install a new power supply:
1. Grasp the module handle and push firmly
into the slot.
2. Connect the AC power cable.
For complete replacement instructions, refer to the Spectrum Component Replacement Guide.
Removing and Replacing a MediaPort Chassis Front Bezel
1
2
To remove the bezel:
1. Remove the center screws on each side
of the chassis that secure the bezel to
the chassis.
.
Note: Keep the rack ear in place.
2. Unplug the bezel power/data connector.
3. Pull the bezel away from the chassis.
To install the new bezel:
1. Attach the bezel power/data connector.
2. Align the bezel in front of the chassis so that
the Omneon logo appears in the top-left corner,
and the metal corners of the bezel are level with
the rack ears of the chassis.
3. Press the bezel straight onto the chassis.
4. Attach the two center screws on each side of the
chassis to secure the bezel to the chassis.
For complete replacement instructions, refer to the Spectrum
Component Replacement Guide.
Harmonic Technical Support: +888 673 4896 (Americas), +65 6542 0050 (Asia Pacific), + 44 1252 555 450 (EMEA),
+7 495 926 4608 (Russia, CIS), +81 3 5565 6737 (Japan), +86 10 8391 3313 (China, mainland)
28-0339 Rev. E
License Options for MediaPort 7000 Series Modules
The following table shows available MediaPort 7000 Series module options.
Model
Number
MPEG-2
H.264
Proxy
Rec
MIP-7300
MIP-7301
X
Play
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
MIP-7600
MIP-7601
X
Rec/Play
X
Rec
ProRes
VC-3
Play
X
Play
AVC-Intra
Rec
MIP-7100
MIP-7101
DV/DVCPRO
Play
The following table shows MediaPort 7000 Series module license options.
Product ID
SD
HD
Up /Down/
Cross
Conversion
and HD/SD
Simulcast
APR
X
X
X
DMH*
X
X
X
DMS*
X
DVH
X
DVS
X
M2H*
X
M2S*
X
UVP
X
X
X
VC3
X
X
X
VC3P
X
X
X
VC3R
X
X
X
X
MPEG-2
Rec
DV/DVCPRO
AVC-Intra
Play
Rec/Play
Rec
Play
X
X
X
X
X
X
X
X
X
X
X
VC-3
ProRes
Rec
Play
X
X
Play
X
X
X
X
X
X
X
X
X
X
X
X
X
SPL-PRORES
X
*For DMH, DMS, M2H, and M2S, MPEG-2 Rec and Play is only available on MediaPort 7300 Series modules.
The following table shows additional licensed features available for MediaPort 7000 Series modules.
Product ID
SPL-OPC
Description
Onboard playout control for one channel of Spectrum ChannelPort or MediaPort 7000
SPL-OMF
Onboard Media Fetch for one video server, enables Media Fetch for all OPC licenses installed
SPL-STL
Onboard subtitle insertion license for one channel of Spectrum ChannelPort or MediaPort 7000
For more details on the MediaPort 7000 module, refer to “MediaPort 7000 Series Reference” in the Spectrum
Installation and Hardware Reference Guide.
Harmonic Technical Support: +888 673 4896 (Americas), +65 6542 0050 (Asia Pacific), + 44 1252 555 450 (EMEA),
+7 495 926 4608 (Russia, CIS), +81 3 5565 6737 (Japan), +86 10 8391 3313 (China, mainland)
28-0339 Rev. E