Sync ™ Order Guide

Sync™
Project Name
Spec Type
Wall
Notes
Direct/Indirect
1 T8
Order Guide
Some combinations of product options may not be available. Consult factory for assistance with your specification.
7408
–
T01
–
–
–
–
Product Series & Type
Lamping
Lower Optics
Upper Optics
Run Length
Wiring
Voltage
Ballast
Color & Finish
Sync Wall
1 T8
Q MesoOptics® Lens
N None
Enter the total
run length in feet
(4ft increments)
1
3
5
7
1 120V
2 277V
E Standard Ballast
W Standard White
C Factory Color
X Custom Color
See details on
reverse
Consult website for complete list of
standard wiring options
Consult website for ballast
manufacturer information
Consult website for color
and finish options
Upgrades & Accessories
Lamps Included
1 cct
1 cct w/ Emergency cct
1 cct w/ Battery Pack
1 cct Dimming
Please indicate with check mark.
Dust Cover
1-9/16"
6-1/16"
© 2009 Ledalite
Phone: 604.888.6811
Fax: 800.665.5332
Web: www.ledalite.com
Filename 7408T01QN.pdf Rev 1.2
Sync™
Additional Information
Wall
Direct/Indirect
Modules
1 T8
Module length excludes endcaps.
Photometry
Candela Distribution
0
5
15
25
35
45
55
65
75
85
90
95
105
115
125
135
145
155
165
175
180
0
387
406
458
500
404
250
154
84
33
3
0
110
295
424
517
498
452
380
301
229
193
Horizontal Angle
22.5 45 67.5
90
387
397
422
443
391
258
149
77
31
4
0
122
273
391
417
405
370
325
274
223
193
387
373
326
243
172
120
87
57
27
6
0
4
13
29
39
48
67
85
111
161
193
387
384
368
335
279
205
133
76
30
3
0
18
47
79
110
138
160
175
187
192
193
387
376
339
278
202
143
98
60
26
5
0
5
18
33
47
65
81
96
128
170
193
Zonal
Lumens
135
135
90
90
600 cd
Specifications
29
114
170
191
176
144
107
67
29
Avg. Luminance (cd/m2)
70
50
30
10
70
70
50
30
50
50
30
10
0
0
Vertical
Angle
0 RCR
1
2
3
4
5
6
7
8
9
10
68
63
57
52
48
44
41
38
35
33
30
68
60
53
47
41
37
33
30
27
25
23
68
58
49
42
37
32
28
25
22
20
18
68
56
46
39
33
28
25
22
19
17
15
63
57
52
48
44
40
37
35
32
30
28
63
55
49
43
38
34
31
28
25
23
21
63
53
45
39
34
30
26
24
21
19
17
52
46
41
36
32
29
26
24
22
20
18
52
45
39
33
29
26
23
20
18
17
15
52
43
37
31
27
23
20
18
16
14
13
29
25
22
19
16
14
13
11
10
9
8
55
65
75
85
Phone: 604.888.6811
0
Horizontal Angle
45
90
3283
2430
1559
421
2835
2199
1417
421
1855
1649
1276
842
IES files for this and other
photometric options can be
downloaded online at
www.ledalite.com
Fax: 800.665.5332
Housing
Die-formed 18 gauge cold-rolled steel.
Weight
2.4 lb/ft.
52.1% Up / 47.9% Down
Ceiling:
Wall:
© 2009 Ledalite
90-90
45-135
0-180
0
Based on a floor reflectance of 0.2
Due to continuing product improvements, Ledalite reserves the right to change specifications without notice.
45
45
Coefficients of Utilization (%)
80
For further details, refer to installation instructions online at
www.ledalite.com
180
22
91
154
183
166
126
83
42
10
1/16"
• Mounts variable within 2"-5" of end or joint. On 8ft module,
additional mount to be located within 2"-5" of center of
module.
• Maximum distance between mounts is 48". Note: Fixture is
flush with wall.
* Between 90-180˚ vertical angle
Meets RP-1-04 recommendations for VDT-Intensive spaces
Vertical
Angle
Endcap
Mounting Hardware
Peak Candela Value* 527 @ 128°
Peak to Zenith Ratio* 2.7 : 1
9901159
7408T01QN.ies
64.4%
Nominal Length
4’ 0”
8’ 0”
Refer to installation instructions
for exact mount spacing
Optics QN MesoOptics® Lens
Report Summary
Report #
Filename
Efficiency
Module
4ft
8ft
Web: www.ledalite.com
Optical System
High efficiency optical system providing an optimal asymmetric direct/
indirect distribution. Lower optics consist of a flat acrylic panel with a
layer of MesoOptics® film that provides a controlled distribution in the
lower hemisphere.
Ballast
Electronic. Supplied with pre-installed ballast disconnects as per
changes to the National Electrical Code.
Approvals
Certified to UL and CSA standards.
Finish
High-quality powder coat. Available in Ledalite Standard White
(textured matte finish), and a selection of other factory and customerspecified colors. Consult factory for details.
Endcaps
Die-cast endcaps.
Joints
Self-aligning joining system with hands-free pre-joining wire access.
Mounting
Fixture is mounted flush to wall using hidden wall brackets. Brackets
attach to existing structure, variable within 2"-5" of end or joint.
Electrical
Factory pre-wired to section ends with quick-wire connectors.
Filename 7408T01QN.pdf Rev 1.2