FRYBABY2 Compact Burn-in Generator Made in USA

FRYBABY2
Compact Burn-in Generator
Made in USA
FRYBABY2 Compact Burn-in Generator
2
Copyrights & Trademarks
© Copyright Hagerman Audio Labs 2014. All rights reserved. No part of this
document may be photocopied, reproduced, or translated to another language
without the prior written consent.
Disclaimer
The information contained in this document is subject to change without notice.
Hagerman Audio Labs shall not be liable for errors contained herein or for
consequential damages in connection with the furnishing, performance, or use of this
material.
Warranty
Hagerman Audio Labs warrants this product free of defects in materials and
workmanship for a period of 10 years. If you discover a defect, Hagerman Audio
Labs will, at its option, repair or replace the product at no charge to you provided
you return it during the warranty period, transportation charges prepaid to
Hagerman Audio Labs. This warranty does not apply if the product has been
damaged by negligence, accident, abuse or misuse or misapplication, has been
damaged because it has been improperly connected to other equipment or has been
modified without the express written permission of Hagerman Audio Labs. This
warranty is limited to the replacement or repair of this product and not to damage to
equipment of other manufacturers. Any applicable implied warranties, including
warranty of merchantability, are limited in duration to a period of the express
warranty as provided herein beginning with the original date of purchase and no
warranties, whether express or implied shall apply to the product thereafter. Under
no circumstances shall Hagerman Audio Labs be liable for any loss, direct, indirect,
incidental, special, or consequential damage arising out of or in connection with the
use of this product.
Hagerman Audio Labs
PO Box 61911
Honolulu, HI 96839
808-383-2704
www.haglabs.com
FRYBABY2 Compact Burn-in Generator
3
Description
The FryBaby2 audio system conditioner is a burn-in signal generator designed
especially for cables and interconnects. It can also be used to burn-in linestages,
phonostages, and amplifiers. The sophisticated electronic waveform – a combination
of wideband noise and variable frequency amplitude modulation – is designed to
exercise both low and high frequency characteristics of conductors and insulators.
Specifications
Item
Output Voltage
Current Limit
Signal Bandwidth
AC Voltage
Specification
1Vrms (LINE), 10mVrms (MM), 1mVrms (MC)
10mA
10Hz to 1MHz
120V/240V
FRYBABY2 Compact Burn-in Generator
4
Operation
The FryBaby2’s control knob sets the mode of operation. MC selects an output level
suitable for driving moving coil phonostage inputs (-60dB), MM for moving magnet
phonostages (-40dB), and ON for everything else (line level). The internal LED blinks
at the rate of modulation.
There are two modes of cable burn-in, voltage and current. Both are required for
maximum effectiveness.
Voltage Mode
In voltage mode the cable dielectric is excited by electric fields. Leave the far end of
the cable open-circuited (see diagrams in following section).
Current Mode
In current mode, the cable is short circuited, and conductors are exercised via
magnetic fields. Short-circuit the far end of the cable or form a loop by returning the
cable to the other FryBaby2 output. Current mode is not applicable when using the
FryBaby2 to burn in amplification.
Duration
It is best to do a voltage burn for 24 hours followed by a current burn for 48 hours.
Note: silver conductors typically take twice as long!
FRYBABY2 Compact Burn-in Generator
5
Connections
The FryBaby2 is designed to burn-in and condition cables offline. It can also be used
as a signal generator to break-in amplifiers or other electronics.
RCA
The FryBaby2 can burn in a stereo pair of interconnects by using the female-tofemale adapter at the far end. First, do a voltage burn by connecting the
interconnect pair directly to the FryBaby2 outputs. Set to ON. After the voltage burn,
do a current burn by inserting the adapter to close the loop.
Phonostage, Linestage, Amplifier
Amplification electronics are burned in using voltage mode. Connect the FryBaby2
outputs to the inputs on your phonostage (you’ll need an interconnect). Set the
output amplitude to either MC or MM, depending on the gain of your phonostage.
This sets the burn-in signal to the correct amplitude and equalization. For linestages
or other types of amplifiers, use the ON level output. Amplifier must be powered on.
Troubleshooting
If the LED is not lit, check the power supply and rotary switch.
R01
100
BO
C+
C-
OS
LV
01
02
04
07
06
J01
9V
03
08
VO
05
U01
TC7660S
D01
1N4148
S01A
C06
47uF
D02
1N4148
C03
47uF
9V
C07
47uF
C04
47uF
R02
47k
Q01
2N3904
C08
100nF
R05
100k
C05
47uF
C09
47uF
R07
10k
3
2
4
R04
100k
R03
10k
1
R06
10k
7
R08
10k
13
14
15
C10
47uF
5
9V
8
6
11
U02A
LM13700
16
PO Box 61911
Honolulu, HI 96839
Hagerman Audio Labs
6
11
9V
10
C11
100pF
12
U02B
LM13700
SIGNAL
9
MODU
R10
10k
R09
4.7k
VCC
R12
100k
R11
100k
C12
47uF
R13
47k
3
2
R14
100k
5
6
9V
9V
1
U03A
LM358
7
U03B
LM358
R16
100k
R15
100k
Q02
2N3904
R17
100k
R18
47k
5
6
C13
100nF
9V
7
U04B
LM358
9V
R22
100k
R21
47k
9V
1
U04A
LM358
PO Box 61911
Honolulu, HI 96839
Hagerman Audio Labs
R20
100k
R19
100k
3
2
MODU
D03
LED
R23
2.2k
SIGNAL
C15
3.3nF
R26
1M
C16
47uF
R28
100
R27
1k
C14
1nF
R25
100k
R24
10k
9V
C01
1nF
S01B
C17
47uF
R31
10k
R32
10k
3
2
R33
10k
5
6
R30
10k
9V
9V
1
U05A
NE5532
7
U05B
NE5532
R35
10k
R37
100
R34
10k
R36
100
J03
J02
PO Box 61911
Honolulu, HI 96839
Hagerman Audio Labs
C19
47uF
C18
47uF