TA Staircase Angles E-Z Base™/E

Decks & Fences
TA Staircase Angles
For use in structurally-sound staircase framing. The TA eliminates
costly conventional notching.
MATERIAL: 12 gauge
FINISH: TA9Z/TA10Z—ZMAX® coating; TA9SS/TA10SS—stainless steel;
see Corrosion Information, pages 14-17.
ORDER: May be ordered TA9ZKT and TA10ZKT with two ZMAX TAs
and 1⁄4"x1 1⁄2" Strong-Drive® SDS Heavy-Duty Connector screws.
TA9Z
Typical TA9Z
Installation
(Install at
each end of
stair tread)
These products are available with additional corrosion protection. Additional products on
this page may also be available with this option, check with Simpson Strong-Tie for details.
Fasteners
Model
No.
Stringer
Factored Resistance
(K D = 1.00)
Tread
TA9Z
3-SDS 1⁄4"x1 1⁄2"
2-SDS 1⁄4"x1 1⁄2"
TA10Z
3-SDS 1⁄4"x1 1⁄2"
4-SDS 1⁄4"x1 1⁄2"
TA10Z
4-SDS 1⁄4"x1 1⁄2"
3-SDS 1⁄4"x1 1⁄2"
D.Fir-L
S-P-F
lbs
lbs
kN
kN
1025
945
4.56
4.23
1025
1260
4.56
5.60
1370
1260
6.10
5.60
TA10Z
1.Values may be adjusted for other
load durations according to code.
2.See page 25 for SDS information.
3.HDG 1⁄4" lag screws may be used.
Resistances must be calculated in
accordance with CSA O86-14 but may
not be greater than tabulated values.
Predrill in accordance with code.
4.Values assume dry service conditions.
Multiply values by 0.67 for wet
service conditions.
Alternate
Installation
of TA10Z
Inverted for
Double 2x6 Treads
Replacing an entire fence can be an expensive
and difficult task. Simpson Strong-Tie® offers a
line of products designed to help make reinforcing
fence posts easy and economical. The E-Z Base,
E-Z Mender and E-Z Spike offer simple solutions
for all types of fence post projects.
E-Z Spike (Model No. FPBS44)
•Allows easy installation of 4x4 wood posts
without digging holes or pouring concrete.
•Can be used for a variety of applications
where quick-to-install posts are needed.
E-Z Mender ( Model No. FPBM44E)
•Allows easy repair of rotted or damaged
4x4 wood posts installed in concrete or dirt.
•Reinforces weakened wood posts without
having to replace the post or the concrete.
•Sold individually. Use in pairs.
E-Z Base (Model No. FPBB44)
•Allows easy installation of 4x4 wood posts
on existing concrete.
MATERIAL: 12 gauge
FINISH: Black powder-coat
INSTALLATION:
• See flier F-EZFPP13.
•Attach post to E-Z Spike or E-Z Base
with 8-1⁄4" Strong-Drive® SDS Heavy-Duty
Connector screws or 1⁄4" HDG lag screws
and attach post to E-Z Mender using
6 HDG nails or screws per part.
NOTE: • Notwithstanding the terms of the Limited
Warranty, Simpson Strong-Tie does not
guarantee, represent or warrant that this
product will perform under, or prevent or
reduce damage caused by corrosion, any
seismic, wind, atmospheric, or other
load-producing event.
These products are approved for installation
with the Strong-Drive ® SD Connector screw.
See page 24 for more information.
210
3⁵⁄₈"
Block
5³⁄₈"
34⁷⁄₈"
4-¹⁄₂" Dia.
Anchors
5¹⁄₂"
11⁵⁄₈"
28"
E-Z Spike™
(FPBS44)
E-Z Mender™
(FPBM44E)
E-Z Base™
(FPBB44)
65⁄8"
3 ⁄4"
11⁄2" Typ.
Typ.
5 ⁄8"
Typ.
35⁄16" 35⁄8"
35⁄8"
E-Z Base™ (FPBB44) Top View
Catalogue C-C-CAN2015 © 2015 SIMPSON STRONG-TIE COMPANY INC.
Decks & Fences
E-Z Base™/E-Z Mender™/E-Z Spike™ Fence Products