T42BD820NS 42-INCH SIDE-BY-SIDE REFRIGERATOR WITH

T42BD820NS
42-INCH SIDE-BY-SIDE REFRIGERATOR WITH
EXTERNAL ICE AND WATER DISPENSER
PROFESSIONAL SERIES GRILLE & HANDLES
GENERAL PROPERTIES
Multi-Flow Air Tower
Yes
Water Filter
Yes
Lighting
Incandescent Bulb
Full Width Shelves - Refrigerator
4
Adjustable Shelves - Refrigerator
Yes
Shelf Material - Refrigerator
Frameless Glass
Humidity Control Drawer
Yes
Door Bins - Refrigerator
4
Gallon Door Bins
5
Defrost Process - Freezer
Frost-Free
Freezer Drawers
2
Adjustable Shelves - Freezer
4
Shelf Material - Freezer
Metal
Type Of Shelves - Freezer
Wire
Door Bins - Freezer
6
Ice Maker
Yes
Door Open Alarm
Yes
SuperCool
Yes
CAPACITY
Total Unit Gross Capacity (cu. ft.) - AHAM
24.8 cu. ft.
Refrigerator Gross Capacity (cu. ft.)
16 cu. ft.
Freezer Gross Capacity (cu. ft.)
9 cu. ft.
TECHNICAL DETAILS
FEATURES & BENEFITS
- Timeless built-in stainless steel refrigerator
- Full-Filtered external ice and water dispenser
- FlexTemp® Drawer optimized for fish, meat and produce
- Crisper drawers
- Gallon door bins
Current (A)
15 A
Volts (V)
115 V
Frequency (Hz)
60 Hz
Power Cord Length (in.)
84"
Plug Type
120V 3-Wire
DIMENSIONS & WEIGHT
Appliance Dimensions (H x W x D) (in.)
83 3/8" x 42 1/4" x
25 1/8"
Required Cutout Size (H x W x D) (in.)
84" x 41 1/2" x 24"
Net Weight (lbs)
547 lbs
EFFICIENCY
Annual Energy Consumption
826 kWh
WARRANTY
Limited, Entire Appliance, Parts and Labor On
Any Part of The Refrigerator That Fails Because
of A Manufacturing Defect
2 Year
Limited Warranty For Sealed Refrigeration
System*; Parts and Labor
3rd to 6th Year
Limited Warranty For Sealed Refrigeration
System*; Parts Only
7th to 12th Year
* Sealed refrigeration system includes compressor, evaporator, condenser, dryer / strainer and
connection tubing
Page 1 of 4
T42BD820NS
42-INCH SIDE-BY-SIDE REFRIGERATOR WITH
EXTERNAL ICE AND WATER DISPENSER
PROFESSIONAL SERIES GRILLE & HANDLES
Width dimensions are measured
from trim edge to trim edge.
Height dimensions are shown with
leveling legs extended 1/8" (3 mm)
below the rollers.
*When leveling legs are fully
extended to 1 1/4" (32 mm) below
rollers, add 1 1/8" (29 mm) to the
height dimensions.
The depth from the front of the top grille to the
back of the r efrigerator cabinet is 25 1/8" (638 mm).
The water line attached to the back of the
refrigerator is 5 ft (1524 mm) long. Height
dimensions are shown with leveling legs extended
1/8" (3 mm) below rollers.
*When leveling legs are fully extended to 1 1/4"
(32 mm) below r ollers, add 1 1/8" (29 mm) to the
height dimensions.
The location must permit both doors to open to a minimum of 90°. Allow 4 1/2"
(114 mm) minimum space between the side of the refrigerator and a corner wall.
Page 2 of 4
T42BD820NS
42-INCH SIDE-BY-SIDE REFRIGERATOR WITH
EXTERNAL ICE AND WATER DISPENSER
PROFESSIONAL SERIES GRILLE & HANDLES
To avoid tipping during use, the solid soffit
must be within 1" (25 mm) maximum above
the refrigerator. If the solid soffit is higher than
1" (25 mm) or one is not available, then the
refrigerator must be braced.
If the anti-tip boards are needed, they must
be attached to the rear wall studs 80" to 90"
(2032 to 2286 mm) above the floor.
NOTE: A clearance of 1/2" (13 mm) must be
maintained above the top grille in order for
the top grille to be removed.
A grounded 3-wire electrical outlet should
be placed within 16" (406 mm) of the right
side cabinets or end panel. The water shut-off
should be located in the base cabinet on
either side of the refrigerator or some other
easily accessible area. If the water shut-off
valve is not in the cabinets, the plumbing for
the water line can come through the floor or
the back wall.
TOP GRILLE CLEARANCE
WATER LOCATION
All installations must meet local plumbing
code requirements.
The water shut-off should be located in
the base cabinet on either side of the
refrigerator or some other easily accessible
area. The right-hand side is recommended.
The access hole through the cabinet must
be within 1/2" (13 mm) of the rear wall.
6"
(15.2 cm)
6"
(15.2 cm)
1"
(2.54 cm)
24"
(60.96 cm) min.
6"
(15.2 cm)
Page 3 of 4
Refrigerator
2311⁄16 "
1⁄4 "
(6.35
3⁄16 "mm)
(4.7 mm)
24
1⁄8 " cm)
(60.3
(61.3 cm)
231⁄2 "
23(59.7
11⁄16 " cm)
241⁄8 " (60.3 cm)
(61.3 cm)
231⁄2 "
(4.5 mm)
11⁄64 "
(4.5 mm)
3⁄16 "
7⁄32 "
T42BD820NS
11⁄16
(5.5 mm)
3⁄16
42-INCH
SIDE-BY-SIDE REFRIGERATOR WITH
7⁄32
1⁄2
EXTERNAL ICE AND WATER DISPENSER
(4.7 mm)
23
" (59.7 cm)
(60.3 cm)
"
(4.7 mm)
"
(5.5 mm)
23 "
(59.7 cm)
PROFESSIONAL SERIES GRILLE & HANDLES
7⁄32 "
(5.5 mm)
PLANNING INFORMATION
13⁄32 " (10 mm)
5⁄8 "
(15.7 mm)
SIDE PANELS
5⁄8 "
INSET
INSTALLATION
DIMENSIONS
13⁄32 " (10
mm)
Custom side panels may be needed when not enough space is
available to have cabinets on both sides of the refrigerator or when
the refrigerator is placed at the end of a cabinet run. You may
choose an inset, flush, or recessed inset panel installation.
1. Measure the distance
from point A (as shown) to the back wall.
5⁄8 "
13⁄32 " (10 mm)
(15.7 to
mm)
Add 7/32" (5.6 mm)
this measurement to allow the side panel to
fit into the trim.
(15.7 mm)
2. If the panel is more than 1/4" (6.35 mm) thick, rout the front edge
to allow the side panel to fit into the trim.
REFRIGERATOR AND SIDE TRIM DIMENSIONS
The width and height of a side panel are determined by the type of
installation you are planning.
NOTES:
A
– The dimensions shown are actual product dimensions and may
not reflect the needed panel installation dimensions.
– The side panel should be a minimum of
avoid warping.
1/2"
A
(13 mm) thick to
A
– If the opening depth is 25" (635 mm) or more, you may want to
install a support board on rear wall.
FLUSH INSTALLATION DIMENSIONS
Side Trim
1. Measure the distance from point A (as shown) to the back wall.
Refrigerator
¹⁄4 "
2. Attach the(6.35
support
mm) board with a screw or adhesive that is
compatible with aluminum and
wood.
¹¹⁄64 "
(4.5 mm)
24¹⁄8 "
(613 mm)
23¹¹⁄16 "
(603 mm)
³⁄16 "
(4.7 mm)
23¹⁄2 "
(597 mm)
A
7⁄32 "
(5.5 mm)
A
A
Side Trim
RECESSED INSET INSTALLATION DIMENSIONS
¹³⁄32 " (10 mm)
1⁄4 "
(6.35 mm)
5⁄8 "
1. Measure the distance (15.7
frommm)
point A (as shown) to the back wall.
2. Rout the front edge of the support board or attach a 1/4"
(6.35 mm) board to hold the panel in the cabinet side trim.
11⁄64 "
(4.5 mm)
3⁄16 "
(4.7 mm)
A A
A
7⁄32 "
(5.5 mm)
A
13⁄32 " (10 mm)
5⁄8 "
(15.7 mm)
These warranties give you specific legal rights and you may have other rights that vary from state to state. Full warranty and limited warranty from date of installation. For complete warranty
details, refer to your Use & Care manual, or ask your dealer.
Specifications are for planning purposes only. Refer to installation instructions and consult your countertop supplier prior to making counter opening. Consult with a heating and ventilation
engineer for your specific ventilation requirements. For the most detailed information, refer to installation instructions accompanying product or write to Thermador indicating the model
number. Specifications are correct at time of printing. Thermador reserves the right to change product specifications or design without notice. Some models are certified for use in Canada.
Thermador is not responsible for products that are transported from the U.S. for use in Canada.
1 800 735 4328 | USA THERMADOR.COM | CANADA THERMADOR.CA | ©2015 BSH HOME APPLIANCES CORPORATION. ALL RIGHTS RESERVED.
Page 4 of 4
04 / 15