Typical Details – Floors

A4
TOLERANCES:
Construction tolerances between frames
is -0mm +2mm. Frames are manufactured
and assembled to +0mm -2mm.
Applicable to load-bearing schemes
EOS Steel Frame.
2 No. 5.5 x 50mm Tek screws (EOS04)
@ 600mm c/c's, or similar approved, to be
securely fixed through the OSB into
the head of the frame below.
Note: pilot hole required to
prevent burn out of tek screws.
Each lattice fixed to Z plate using 2 No 5.5 x 25mm Tek
screws (EOS02) or similar approved.
(3 No. in each end lattice of cassette)
EOS Steel Frame.
External cladding to suit
clients requirements.
Z plate support - 2mm thick S275 grade galvanised
plate. Depth to suit lattices. Bearing width to suit
wall frame thickness.
2 No. 5.5 x 50mm Tek screws (EOS04) fixed through
Z plate into studs in each of the 4 corners of the floor
cassette or similar approved
Plasterboard finishes & insulation
omitted for clarity.
SECTION
NOTE
All EOS floor cassettes are manufactured with 10mm tolerance between the cassette and the steel frame.
Title:
EXTERNAL WALL TO LATTICE FLOOR CASSETTE FIXING DETAIL (LBSO)
STAGE:
Preliminary:
Approval:
Construction:
Drawn By:
Scale:
n.t.s.
Drawing No.
Revision:
121
A
Approved By:
Date:
A4
TOLERANCES:
Construction tolerances between frames
is -0mm +2mm. Frames are manufactured
and assembled to +0mm -2mm.
Applicable to load-bearing schemes
EOS Steel Frame.
2 No. 5.5 x 50mm Tek screws (EOS04)
@ 600mm c/c's, or similar approved, to be
securely fixed through the OSB into
the head of the frame below.
Note: pilot hole required to
prevent burn out of tek screws.
2 No. 5.5 x 25mm Tek screws (EOS02)
fixed through Z plate into floor cassette at
600mm c/c's. or similar approved
External cladding to suit
clients requirements.
EOS C - SECTION FLOOR CASSETTE
EOS Steel Frame.
Z plate support - 2mm thick S275 grade galvanised
plate. Depth to suit lattices. Bearing width to suit
wall frame thickness.
2 No. 5.5 x 50mm Tek screws (EOS04) fixed through
Z plate into studs in each of the 4 corners of the floor
cassette or similar approved
Plasterboard finishes & insulation
omitted for clarity.
SECTION
NOTE
All EOS floor cassettes are manufactured with 10mm tolerance between the cassette and the steel frame.
Title:
EXTERNAL WALL TO FLOOR CASSETTE FIXING DETAIL (LBSO)
STAGE:
Preliminary:
Approval:
Construction:
Drawn By:
Scale:
n.t.s.
Drawing No.
Revision:
122
A
Approved By:
Date:
A4
TOLERANCES:
Construction tolerances between frames
is -0mm +2mm. Frames are manufactured
and assembled to +0mm -2mm.
Applicable to load-bearing schemes
EOS Steel Frame.
2 No. 5.5 x 50mm Tek screws (EOS04)
@ 600mm c/c's, or similar approved, to be
securely fixed through the OSB into
the head of the frame below.
Note: pilot hole required to
prevent burn out of tek screws.
Z plate and boarding stop on centre
line of vertical steel frame.
(5mm tolerance)
EOS Steel Frame.
EOS C - SECTION FLOOR CASSETTE
2 No. 5.5 x 25mm Tek screws (EOS02)
fixed through Z plate into floor cassette at
600mm c/c's. or similar approved
2 No. 5.5 x 50mm Tek screws (EOS04) fixed through
Z plate into studs in each of the 4 corners of the floor
cassette or similar approved
Each lattice fixed to Z plate using 2 No 5.5 x 25mm Tek
screws (EOS02) or similar approved.
(3 No. in each end lattice of cassette)
2 No. 5.5 x 50mm Tek screws (EOS04) fixed through
Z plate into studs in each of the 4 corners of the
lattice floor cassette or similar approved
Plasterboard finishes & insulation
omitted for clarity.
SECTION
NOTE
All EOS floor cassettes are manufactured with 10mm tolerance between the cassette and the steel frame.
Title:
INTERNAL WALL TO FLOOR FIXING DETAIL (lattice & C section cassettes) (LBSO)
STAGE:
Preliminary:
Approval:
Construction:
Drawn By:
Scale:
n.t.s.
Drawing No.
Revision:
123
A
Approved By:
Date:
A4
TOLERANCES:
Construction tolerances between frames
is -0mm +2mm. Frames are manufactured
and assembled to +0mm -2mm.
Applicable to load-bearing schemes
EOS Steel Frame.
2 No. 5.5 x 50mm Tek screws (EOS04)
@ 600mm c/c's, or similar approved, to be
securely fixed through the OSB into
the head of the frame below.
Note: pilot hole required to
prevent burn out of tek screws.
EOS Steel Frame.
External cladding to suit
clients requirements.
4 No 5.5 x 25mm Tek screws (EOS02)
fixed through 60 x 60 x 2.5mm angle bracket.
Each lattice beam to have 2 brackets,1 bracket fixed
at each end on opposite faces.
2 No 5.5 x 25mm Tek screws (wafer heads) (EOS05)
fixed through underside of Z plate into
bottom chord of each lattice.
Z plate fixed to each vertical stud using 1 No
5.5 x 25mm Tek screw (EOS02)
prior to placement of lattice beams.
Plasterboard finishes & insulation
omitted for clarity.
SECTION
NOTE
All EOS lattice beams are manufactured with 10mm tolerance between the beam and the steel frame.
Title:
EXTERNAL WALL TO LATTICE FLOOR FIXING DETAIL (site installed) (LBSO)
STAGE:
Preliminary:
Approval:
Construction:
Drawn By:
Scale:
n.t.s.
Drawing No.
Revision:
124
A
Approved By:
Date:
A4
TOLERANCES:
Construction tolerances between frames
is -0mm +2mm. Frames are manufactured
and assembled to +0mm -2mm.
Applicable to load-bearing schemes
1
FLOOR CASSETTE
1
ELEVATION
EOS Steel Frame.
2 No. 5.5 x 50mm Tek screws (EOS04)
@ 600mm c/c's, or similar approved, to be
securely fixed through the OSB into
the head of the frame below.
Note: pilot hole required to
prevent burn out of tek screws.
External cladding to suit
clients requirements.
EOS Steel Frame.
2 No. 5.5 x 50mm Tek screws (EOS04)
fixed through end joist into each vertical stud to
provide lateral support to steel frame or similar
approved.
Plasterboard finishes & insulation
omitted for clarity.
SECTION 1-1
NOTE
All EOS floor cassettes are manufactured with 10mm tolerance between the cassette and the steel frame.
Title:
NON LOADBEARING EXTERNAL WALL TO FLOOR CASSETTE FIXING DETAIL
(without Z plate) (LBSO)
STAGE:
Preliminary:
Approval:
Construction:
Drawn By:
Scale:
n.t.s.
Drawing No.
Revision:
125
A
Approved By:
Date:
A4
TOLERANCES:
Construction tolerances between frames
is -0mm +2mm. Frames are manufactured
and assembled to +0mm -2mm.
Applicable to load-bearing schemes
75
EA
6/
2
Simpson EA 756/2C50 50 x 70 x 2mm bracket (60mm wide) at approx.
1200 c/c's. fixed into lattice with 2 No 5.5 x 25mm Tek
screws (EOS02) and fixed into vertical stud with 4 No. 5.5
x 25mm Tek screws (EOS02) or similar approved
Plasterboard finishes & insulation
omitted for clarity.
ELEVATION
NOTE
Bracket to be fixed at locations to suit stud and lattice diagonal as indicate.
Title:
TYPICAL NON LOADBEARING WALL RESTRAINT WHEN LATTICE JOISTS RUN
PARALLEL (LBSO)
STAGE:
Preliminary:
Approval:
Construction:
Drawn By:
Scale:
n.t.s.
Drawing No.
Revision:
126
A
Approved By:
Date:
A4
TOLERANCES:
Construction tolerances between frames
is -0mm +2mm. Frames are manufactured
and assembled to +0mm -2mm.
EOS Steel frame.
Applicable to load-bearing schemes
2 No. 5.5 x 50mm Tek screws (EOS04)
@ 600mm c/c's, or similar approved, to be
securely fixed through the OSB into
the head of the frame below.
Note: pilot hole required to
prevent burn out of tek screws.
EOS FLOOR CASSETTE LATTICE
Box noggins fixed between vertical lattice members
on the line of the loadbearing stud wall. Fixed into each
vertical stud using 2 No. 5.5 x 25mm Tek screws (EOS02)
EOS Steel frame.
Each lattice fabricated with a vertical member
on the line of the loadbearing stud wall.
Plasterboard finishes & insulation
omitted for clarity.
2 No. 5.5 x 25mm Tek screws (EOS02)
fixed through head of frame into bottom chord
of each lattice beam or similar approved
SECTION
Title:
INTERMEDIATE LOAD BEARING WALL SUPPORT TO LATTICE FLOOR (LBSO)
STAGE:
Preliminary:
Approval:
Construction:
Drawn By:
Scale:
n.t.s.
Drawing No.
Revision:
127
A
Approved By:
Date:
DRAWING INDICATIVE ONLY:
A4
TOLERANCES:
Construction tolerances between frames
is -0mm +2mm. Frames are manufactured
and assembled to +0mm -2mm.
LATTICE FLOOR CASSETTE 'B'
EOS Lattice B
Plasterboard finishes omitted
for clarity.
EOS Lattice B
EOS Lattice A
EOS Lattice A
LATTICE FLOOR CASSETTE 'A'
Simpson PWT 200 tie
fixed to underside of each lattice using
2 No. 5.5 x 25mm Tek screws (EOS05) with wafer heads
or similar approved
SECTION
PLAN
Plate detail required to prevent differential movement
between adjacent lattice floor cassettes over 3m span.
Title:
LATTICE FLOOR CASSETTE PLATE CONNECTION DETAIL (LBSO)
STAGE:
Preliminary:
Approval:
Construction:
Drawn By:
Scale:
n.t.s.
Drawing No.
Revision:
128
A
Approved By:
Date:
A4
TOLERANCES:
Construction tolerances between frames
is -0mm +2mm. Frames are manufactured
and assembled to +0mm -2mm.
Applicable to load-bearing schemes
Extent of OSB flooring shown
hatched.
End joist kept 200mm back from corner
to form service void.
EOS Steel frame
Noggin
Z Plate
100mm Dia.
EOS Steel frame
Ladder noggin
OSB to be cut out on
site locally to services as required.
Z Plate kept 200mm back from corner
to form service void.
Plasterboard finishes & insulation
omitted for clarity.
PLAN
Title:
TYPICAL SERVICE RISER DETAIL IN CORNER OF ROOM (For 100mm dia SVP) (LBSO)
STAGE:
Preliminary:
Approval:
Construction:
Drawn By:
Scale:
n.t.s.
Drawing No.
Revision:
129
A
Approved By:
Date:
DRAWING INDICATIVE ONLY:
A4
TOLERANCES:
Construction tolerances between frames
is -0mm +2mm. Frames are manufactured
and assembled to +0mm -2mm.
LA
TT
ICE
LATTICE FIXED TO DOUBLE
STUD USING 4 No 5.5 x 25mm
TEK SCREWS (EOS02)
LIN
TE
L
DOUBLE
JAMB STUD
LATTICE DEPTH TO SUIT HEIGHT
BETWEEN WINDOW HEAD AND
FLOOR / ROOF ABOVE.
AD
HE
BEARING NOGGING FIXED TO
DOUBLE STUD USING
4 No. 5.5 x 25mm TEK SCREWS (WAFER HEADS) (EOS05)
LATTICE FIXED TO BEARING
USING 2 No 5.5 x 25mm TEK SCREWS (EOS02)
Title:
TYPICAL LATTICE LINTEL DETAIL (spans over 4200mm) (LBSO)
STAGE:
Preliminary:
Approval:
Construction:
Drawn By:
Scale:
n.t.s.
Drawing No.
Revision:
130
A
Approved By:
Date:
O
G
IN
EN
P
FO