McKissick® Blocks

Transcription

McKissick® Blocks

McKissick® Blocks
®
k c i s s i Kc M
McKissick®
Blocks
s k c o l B
Copyright © 2002 The Crosby Group, Inc.
All Rights Reserved
229
McKissick & Lebus
Snatch Blocks
What It Takes To Be
418
³&URVE\ 2U (TXDO´
DESIGN
COMPETITION
The theoretical reserve capability of a snatch block should
be at least 4 to 1. Known as the DESIGN FACTOR, it is
usually computed by dividing the ultimate load by the
working load limit. The ultimate load is the average load
or force at which the block fails or no longer supports the
load. The working load limit is the maximum mass or
force which the product is authorized to support in
general service. The design factor is generally expressed as
a ratio such as 4 to 1.
Also important in the design of snatch blocks is the
selection of proper steel used in components and
consideration as to fatigue life.
END FITTING CONNECTIONS
Interchangeability of end fittings is important, and should
be easily achieved without dissassembly of the block.
It is also important that end fittings are quenched and
tempered in order to reduce the risk of brittle, catastrophic
failure.
BLOCK CONSTRUCTION
The block performance depends greatly on the sheave and
block construction. All steel construction, including side
plates, pins, and sheaves is desireable. Bronze bushings are
recommended for slow line speeds and frequent use.
Roller bearings are recommended for faster line speeds
and more frequent use at greater loads. The ability to
individually lubricate all sheaves is essential.
Secondary securement of bolt connecting the end fitting to
the block is recommended.
FULL LINE IDENTIFICATION
The availability of a full range of snatch blocks is essential
to insure that the appropriate block is available for a
specific application.
All snatch blocks must be identified by type, size of block,
size of wire line to be used, working load limit, and the
manufacturer’s name boldly marked on the product.
STANDARDS ORGANIZATION
All snatch blocks utilized in the oilfield should be
manufactured by a source that is both API Q1 and
ISO 9001 certified.
APPLICATION INFORMATION
Detailed application information will assist you in the
proper selection of snatch blocks. This information is most
effective when provided at the point of application, as well
as in supporting brochures and engineering information.
A formal application and warning system that attracts the
attention of the user, clearly informs the user of the factors
involved in the task, and informs the user with the proper
application procedures is needed.
Ask: Are their snatch blocks metric
rated?
Ask: What is the metric design factor?
Ask: Are their snatch blocks fatigue
rated?
L-170
CROSBY
McKissick and Lebus snatch blocks
are dual rated with a design factor
of 4 to 1 for metric and 4.5 to 1 in
short tons.
incorporate the proper selection of
steel and are also fatigue rated.
Most do not provide metric
ratings with a design factor of 4 to
1, nor fatigue rated snatch blocks.
Ask: Are the end fittings forged,
quenched and tempered?
Ask: Are the end fittings interchangable?
Ask: Are their blocks all steel
construction?
Ask: Do their blocks have secondary securement of the pins?
use genuine Crosby forged,
quenched and tempered hooks and
shackles.
are of “all steel” construction. They
also have a secondary end fitting
securement system. In addition,
sheaves are individually lubricated.
Ask: Are all sheaves individually
lubricated?
Ask: Do they have a full range of
snatch blocks?
Ask: Are their snatch blocks properly
marked with critical information?
Most competitors do not have the
full range of snatch blocks that
Crosby offers.
Ask: Are they API Q1 certified?
Ask: Are They ISO 9001 Certified?
Most competitors are not API Q1
certified or ISO 9001 Certified.
Ask: Does each snatch block have the
application and warning information
attached to it?
McKissick and Lebus provide
the most complete line of snatch
blocks in the industry.
All McKissick and Lebus snatch
blocks are identified by type, size
of block, size of wire line to be
used, working load limit (in both
metric and short tons), and the
manufacturer’s name boldly
marked on the product.
Crosby’s McKissick plant is API Q1
certified. McKissick is also certified
to ISO 9001 standards by Det
Norske Veritas (DNV).
Crosby provides detailed
application and warning
information attached to each snatch
block.
Most competitors do not have
application and warning infomation
with each snatch block.
Remember, “When buying Crosby, you’re buying more than product, you’re buying Quality.”
230
All Rights Reserved
Crosby Value Added
•
Dual rated: To meet the requirements of both short tons and metric tons.
•
Metric rating: McKissick and Lebus snatch blocks are metric rated to a design factor of 4 to 1. Since
they are metric rated, with a world class design, they are applicable to worldwide use without
conversion.
•
U.S. rating: When compared to other blocks which are rated in short tons, the design factor of
McKissick and Lebus snatch blocks are 4.5 to 1.
•
Fatigue properties: McKissick and Lebus snatch blocks are fatigue rated. The blocks are designed to
meet specific fatigue performance levels. They meet the requirements for the new Euronorm
Standards: 20,000 cycles at 1-1/2 times the Working Load Limit.
•
Latch Kits: McKissick and Lebus snatch blocks, utilizing a hook as an end fitting connection, can be
equipped with latches.
•
Application information: Application and warning information for tackle block systems is attached
directly to each block. In addition, each block has a product warning sticker attached directly to it for
the purpose of giving specific warning instructions about the block.
•
Lock nut: McKissick snatch blocks have a special high performance lock nut on the nonmoveable side
plate for securing the sheave pin.
•
Sheave and wire line: Sheaves for McKissick and Lebus snatch blocks have a machine formed groove.
•
Secondary Securement Systems: McKissick and Lebus snatch blocks are designed to incorporate a
secondary securement system which retains the end fitting connection bolt when the block is in the
closed position. In addition, a patented system retains the end fitting connection bolt when the block
is in the open position, thus eliminating the loss of block parts.
Tailboard
404
with Hook
418
with Shackle
419
Remember, “When buying Crosby, you’re buying more than product, you’re buying Quality.”
All Rights Reserved
231
Ordering Information
BLOCKS
The following information should be specified:
1.
2.
3.
4.
5.
6.
7.
Stock number (if known)
Sheave Size
Block Number (Catalog number)
Number of Sheaves
Type of Bearings: (BB) Bronze Bushed, (RB) Roller, (TB) Tapered Roller
Type of Hook or Shackle
Wire Rope Diameter.
All crane and some construction blocks are available as shown or with swivel
shackle assembly, duplex swivel hook assembly or quadruple hook assembly
(as illustrated on page 233). Various combinations of bearing assemblies can be furnished; such as bronze bushed sheaves and swivel hooks, roller or tapered
roller bearing sheaves and hook assemblies or a combination of bronze, roller or tapered roller bearings.
EXAMPLE:
18" 380 Series, Triple Sheave, Roller Bearing Crane Block with Roller Bearing
Swivel Hook, 60 ton, light weight, 1" wire rope diameter.
Model Number M60T18L, Stock Number 2012187
SHEAVES
The following information should be specified:
1.
Stock number (if known)
2.
Sheave O.D.
3.
Bearing Type or Plain Bore.
4.
Shaft or Bore Size
5.
Hub Width
6.
Rim Width
7.
Wire Rope Size
8.
Special Machine Features
9.
Special Finishes.
Alemite lubrication through the hub of the sheaves can be installed on special order.
If hub or rim dimensions necessitate a dimension other than those shown in this
catalog please contact: The Crosby Group, Inc. for minimums and maximums. Tapered roller bearing sheave show width over bearing cones, which cannot be altered.
Price and delivery for your special needs, if not shown, are available upon request.
Please Contact:
U.S.A.
The Crosby Group, Inc.
P.O. Box 3128
Tulsa, Ok. 74101-3128
(918) 834-4611
Fax (918) 832-0940
232
CANADA
Crosby Canada Ltd.
145 Heart lake Road
Brampton, Ontario, Canada L6W 3K3
(905) 451-9261
Fax (905) 457-3331
EUROPE
N.V. Crosby Europe
Leuvensebaan 51
2580 Putte, Belgium
32-15-757125
Fax 32-15-753764
All Rights Reserved
Construction and Crane Blocks
Some of the most important considerations in your
block requirements are:
AVAILABLE BEARING TYPES
• Bronze Bushed — S.A.E. 660 bronze with figure “8” oil groove (See Fig. B-1).
• Double row sealed tapered roller bearing (See Fig. T-1).
• Straight roller bearing (See Fig. R-1).
Fig. T-1
Fig. B-1
Fig. R-1
THE SHEAVE
Note the groove form with proper line support and gently rounded lips to prevent line
chafing when fleet angles etc. are present.
Note the groove is completely machined to proper line size.
Note the dense martensitic structure clearly outlined by the etch. This flame hardened
surface in the wear area of the sheave always presents a smooth, uncorrugated, proper
size groove face to the line. Sheaves 14" (356mm) diameter and over flame hardened in
groove to minimum 35 Rockwell “C”. Smaller sheaves can be flame hardened on special order.
McKissick
Blocks
Unretouched Photograph of a section cut from a flamehardened McKissick sheave (etched 21⁄2 Minutes)
(NH4)2S408).
AVAILABLE CONNECTIONS
ALL CRANE AND CONSTRUCTION BLOCKS CAN BE FURNISHED WITH:
Swivel shackle, in selected capacities, with bronze thrust or roller
thrust bearing.
Single hook in capacities to 300
tonnes. (See page 330)
All Rights Reserved
Duplex swivel hook in standard capacities to 1,000 tonnes. Larger
sizes available. (See Page 332)
Quad swivel hook from 200 tonnes
and larger.
233
McKissick® Utility Crane Blocks
380 Series Hook Blocks
• Wide range of product available.
• Capacity: 4,5 to 270 - Larger Models Available.
• Sheave Sizes: 254 mm - 762 mm
• Wire Line Sizes: 11 - 35 mm.
• Manufactured by an ISO 9001 and API Q1 certified
facility.
• All single point shank hooks are genuine Crosby®,
forged alloy steel, Quenched and Tempered, and
have the patented QUIC-CHECK® markings
(Duplex hooks are available on most sizes).
• All 380 Blocks are furnished standard with Roller
Bearings.
• Reeving Guides Standard - All Models.
SEE APPLICATION AND
WARNING INFORMATION
See Pages 286 - 293
• Blocks thru 20 tons use 319N style hooks with
S-4320 latches.
• Sheave lubrication through center pin -Separate lube
channel to each bearing.
• Sheaves fully protected by side plates.
• Dual action hook (Swings and Rotates).
• Repair parts available through world wide
distribution network.
• Design Factor of 4 to 1 (unless otherwise noted).
• All 380 blocks, 406 mm and larger, are furnished
with McKissick® Roll-Forged™ sheaves with flame
hardened grooves.
• Look for the Orange Hook . . . the mark of genuine
McKissick® quality.
OPTIONS AVAILABLE
•
•
•
•
•
•
•
Bronze Bushed Sheaves
Duplex Hooks
Swivel Tee and Shackle Assemblies
Sheave Shrouds
Anti Rotation - Locking Device (75 tons & larger)
Plate Steel Cheek Weights
Third party testing with Certification
available upon request.
Dead End Chart
(Double, Triple, & Quad Sheave Blocks*)
Dimensions
(mm)
Recommended
Wedge Socket
McKissick®
US-422 / US-422T
Wire Rope
U
Utility Socket
Size
T
Hole
(mm)
Thickness
Diameter
Stock No.
Size
11
25.4
32.5
1044309
US4 11
13
25.4
32.5
1044318
US4 13
14
25.4
32.5
1044336
US5 14
16
25.4
32.5
1044345
US5 16
19
31.8
42.2
1044363
US6 19
22
31.8
42.2
1038580
US7 22
25
31.8
42.2
1038607
US8 25
28
44.5
65.0
1038616
US10 28
32
44.5
65.0
1038625
US10 32
* To find Dead End Dimensions for Single Sheave blocks,
refer to table on pages 235 - 246.
US-422T TERMINATOR TM Style.
234
All Rights Reserved
382 - DOUBLE
383 - TRIPLE
384 - QUAD
McKissick
Blocks
381 - SINGLE
Thickness (E) shown is for blocks containing cheek weights (Light Medium - LM, Medium - M, and Heavy - H).
The thickness (E) for non-weighted blocks (Light - L) is measured over side plates.
All Rights Reserved
235
385 - QUINTUPLE
386 - SEXTUPLE
387 - SEPTUPLE
388 - OCTUPLE
Thickness (E) shown is for blocks containing cheek weights (Light Medium - LM, Medium - M, and Heavy - H).
The thickness (E) for non-weighted blocks (Light - L) is measured over side plates.
236
All Rights Reserved
McKissick® Blocks
s k c o l B
e n a r C
s
e i r e S
0 8 3
®
k c i s
s i Kc M
380 Series Crane Blocks
• Specify Wire Line size when ordering. For standard wire line sizes, see Table 1.
M5S10L
M5S10M
M5S12L
M5S12M
M5S12H
M5D10L
M5D10M
2011004
2011013
2011022
2011031
2011036
2011037
2011038
4.5
4.5
4.5
4.5
4.5
4.5
4.5
788
788
835
835
835
697
697
631
631
675
675
675
631
631
M10S10L
M10S10M
M10S12L
M10S12M
M10S12H
M10S14L
M10S14LM
M10S14M
M10S14H
M10S16L
M10S16M
M10S16H
M10D10L
M10D10M
M10D12L
M10D12M
M10D 12H
M10D14L
M10D14LM
M10D14M
M10D 14H
M10T 10L
M10T 10M
2011040
2011049
2011058
2011067
2011071
2011076
2011085
2011094
2011097
2011098
2011099
2011100
2011103
2011112
2011121
2011130
2011135
2011136
2011141
2011137
2011138
2011139
2011140
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
788
788
835
835
835
892
892
892
892
949
949
949
697
697
741
741
741
799
799
799
799
700
700
631
631
675
675
675
733
733
733
733
790
790
790
631
631
675
675
675
722
722
722
722
634
634
M15S10L
M15S10M
M15S12L
M15S12M
M15S12H
M15S14L
M15S14LM
M15S14M
M15S14H
M15S16L
M15S16M
M15S16H
M15D10L
M15D10M
M15D12L
2011148
2011157
2011166
2011175
2011179
2011184
2011185
2011193
2011198
2011202
2011211
2011215
2011220
2011229
2011233
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
788
788
835
835
835
892
892
892
892
949
949
949
697
697
741
631
631
675
675
675
733
733
733
733
790
790
790
631
631
675
lk
380B
A
Overall
Len gth
(mm)
All Rights Reserved
B
Net
Length
(mm )
E
F
ThickWid th
n ess
(mm )
(mm)
4.5 TONN ES
136
356
217
356
136
406
250
406
352
406
136
356
217
356
9 TONNES
136
356
217
356
136
356
250
356
352
356
136
457
186
457
261
457
374
457
136
514
247
514
310
514
136
356
217
356
136
406
250
406
352
406
136
457
186
457
261
457
374
457
195
356
282
356
13.6 TONNES
136
356
217
356
136
406
250
406
352
406
136
457
186
457
261
457
374
457
136
514
247
514
310
514
136
356
217
356
136
406
H
J
Throat
Openin g Hoo k
T hickWith
Flapp er ness
(m m)
(mm)
Dead End ‡
K
Hoo k
Width
(mm)
Std.
Wire
Line
Sizes
(m m)*
T
T hickness
(m m)
U
Pin
Hole
(mm )
Weight
Each
(kg.)
48.5
48.5
48.5
48.5
48.5
48.5
48.5
66.0
66.0
66.0
66.0
66.0
66.0
66.0
49.3
49.3
49.3
49.3
49.3
49.3
49.3
11-16
11-16
13-19
13-19
13-19
11-16
11-16
28.7
28.7
28.7
28.7
28.7
-
35.8
35.8
35.8
35.8
35.8
-
64
91
64
122
181
73
101
48.5
48.5
48.5
48.5
48.5
48.5
48.5
48.5
48.5
48.5
48.5
48.5
48.5
48.5
48.5
48.5
48.5
48.5
48.5
48.5
48.5
48.5
48.5
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
11-16
11-16
13-19
13-19
13-19
13-19
13-19
13-19
13-19
14-22
14-22
14-22
11-16
11-16
13-19
13-19
13-19
13-19
13-19
13-19
13-19
11-16
11-16
28.7
28.7
28.7
28.7
28.7
28.7
28.7
28.7
28.7
28.7
28.7
28.7
-
35.8
35.8
35.8
35.8
35.8
35.8
35.8
35.8
35.8
35.8
35.8
35.8
-
61
90
66
122
197
82
125
163
234
100
177
245
73
100
84
134
204
95
141
180
254
91
120
48.5
48.5
48.5
48.5
48.5
48.5
48.5
48.5
48.5
48.5
48.5
48.5
48.5
48.5
48.5
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
11-16
11-16
13-19
13-19
13-19
13-19
13-19
13-19
13-19
14-22
14-22
14-22
11-16
11-16
13-19
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
—
—
—
42.2
42.2
42.2
42.2
42.2
42.2
42.2
42.2
42.2
42.2
42.2
42.2
—
—
—
62
91
66
134
197
86
132
168
247
109
177
245
73
100
89
237
McKissick®
Blocks
Mo del
No.
Inquiry
Stock
No.
Working
Load
Limit
(t) †
McKissick® 380 Series Crane Blocks
Mo del
No.
M15D12M
M15D12H
M15D14L
M15D14LM
M15D14M
M15D14H
M15D16L
M15D16M
M15D16H
M15T10L
M15T10M
M15T12L
M15T12M
M15T12H
M15Q10L
M15Q10M
Inquiry
Stock
No.
2011238
2011243
2011256
2011257
2011265
2011269
2011270
2011271
2011272
2011273
2011274
2011275
2011283
2011285
2011287
2011288
Working
Load
Limit
(t) †
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
M20S12L
M20S12M
M20S12H
M20S14L
M20S14LM
M20S14M
M20S14H
M20S16L
M20S16M
M20S16H
M20S18L
M20S18M
M20S18H
M20S24L
M20S24M
M20S24H
M20D10L
M20D10M
M20D12L
M20D12M
M20D12H
M20D14L
M20D14LM
M20D14M
M20D14H
M20D16L
M20D16M
M20D16H
M20T10L
M20T10M
M20T12L
M20T12M
M20T12H
M20T14L
M20T14LM
M20T14M
M20T14H
M20Q10L
M20Q10M
M20Q12L
M20Q12M
M20Q12H
2011289
2011290
2011291
2011301
2011302
2011310
2011314
2011315
2011316
2011317
2011319
2011328
2011333
2011330
2011331
2011332
2011335
2011337
2011346
2011355
2011364
2011373
2011374
2011375
2011377
2011378
2011379
2011380
2011381
2011382
2011391
2011400
2011409
2011418
2011420
2011427
2011432
2011433
2011434
2011435
2011436
2011437
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
M25S14L
M25S14LM
M25S14M
M25S14H
M25S16L
M25S16M
M25S16H
M25S18L
M25S18M
2011441
2011443
2011445
2011448
2011451
2011454
2011457
2011461
2011463
23@
23@
23@
23@
23@
23@
23@
23@
23@
lk
380B
238
H
J
Throat
A
B
E
K
Openin g Hoo k
F
Overall
Net
Th ickHoo k
T hickWith
Wid th Flap per ness
Len gth
Leng th
n ess
Width
(mm )
(mm)
(mm )
(mm)
(mm)
(mm)
(mm)
741
675
250
406
48.5
66.0
49.3
741
675
352
406
48.5
66.0
49.3
799
733
136
457
48.5
66.0
49.3
799
733
186
457
48.5
66.0
49.3
799
733
261
457
48.5
66.0
49.3
799
733
374
457
48.5
66.0
49.3
856
790
136
514
48.5
66.0
49.3
856
790
247
514
48.5
66.0
49.3
856
790
310
514
48.5
66.0
49.3
700
634
195
356
48.5
66.0
49.3
700
634
282
356
48.5
66.0
49.3
744
679
195
406
48.5
66.0
49.3
744
679
310
406
48.5
66.0
49.3
744
679
411
406
48.5
66.0
49.3
699
633
252
356
48.5
66.0
49.3
699
633
333
356
48.5
66.0
49.3
18 TONNES
884
714
148
406
70.0
75.5
60.5
884
714
263
406
70.0
75.5
60.5
884
714
364
406
70.0
75.5
60.5
941
772
148
457
70.0
75.5
60.5
941
772
199
457
70.0
75.5
60.5
941
772
274
457
70.0
75.5
60.5
941
772
387
457
70.0
75.5
60.5
998
829
148
514
70.0
75.5
60.5
998
829
259
514
70.0
75.5
60.5
998
829
322
514
70.0
75.5
60.5
1125
929
174
578
70.0
75.5
60.5
1125
929
279
578
70.0
75.5
60.5
1125
929
329
578
70.0
75.5
60.5
1275
1078
174
730
70.0
75.5
60.5
1275
1078
371
730
70.0
75.5
60.5
1275
1078
472
730
70.0
75.5
60.5
746
670
148
356
70.0
75.5
60.5
746
670
229
356
70.0
75.5
60.5
790
714
148
406
70.0
75.5
60.5
790
714
263
406
70.0
75.5
60.5
790
714
364
406
70.0
75.5
60.5
848
772
148
457
70.0
75.5
60.5
848
772
199
457
70.0
75.5
60.5
848
772
274
457
70.0
75.5
60.5
848
772
387
457
70.0
75.5
60.5
905
829
148
514
70.0
75.5
60.5
905
829
260
514
70.0
75.5
60.5
905
829
323
514
70.0
75.5
60.5
749
673
208
356
70.0
75.5
60.5
749
673
289
356
70.0
75.5
60.5
794
718
208
406
70.0
75.5
60.5
794
718
322
406
70.0
75.5
60.5
794
718
424
406
70.0
75.5
60.5
851
775
208
457
70.0
75.5
60.5
851
775
259
457
70.0
75.5
60.5
851
775
332
457
70.0
75.5
60.5
851
775
445
457
70.0
75.5
60.5
748
672
265
356
70.0
75.5
60.5
748
672
346
356
70.0
75.5
60.5
792
716
265
406
70.0
75.5
60.5
792
716
379
406
70.0
75.5
60.5
792
716
481
406
70.0
75.5
60.5
23 T ONNES @ - Ultimate Load is 3.6 times the Working Load Limit
941
772
148
457
70.0
75.5
60.5
941
772
199
457
70.0
75.5
60.5
941
772
274
457
70.0
75.5
60.5
941
772
387
457
70.0
75.5
60.5
998
829
148
514
70.0
75.5
60.5
998
829
260
514
70.0
75.5
60.5
998
829
323
514
70.0
75.5
60.5
1125
929
174
578
70.0
75.5
60.5
1125
929
279
578
70.0
75.5
60.5
Dead End ‡
Std.
Wire
Line
Sizes
(mm)*
13-19
13-19
13-19
13-19
13-19
13-19
14-22
14-22
14-22
11-16
11-16
13-19
13-19
13-19
11-16
11-16
T
T hickness
(m m)
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
U
Pin
Hole
(mm )
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Weight
Each
(kg.)
134
204
95
141
180
254
136
211
277
91
120
98
154
225
117
145
13-19
13-19
13-19
13-19
13-19
13-19
13-19
14-22
14-22
14-22
16-25
16-25
16-25
22-32
22-32
22-32
11-16
11-16
13-19
13-19
13-19
13-19
13-19
13-19
13-19
14-22
14-22
14-22
11-16
11-16
13-19
13-19
13-19
13-19
13-19
13-19
13-19
11-16
11-16
13-19
13-19
13-19
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
42.2
42.2
42.2
42.2
42.2
42.2
42.2
42.2
42.2
42.2
42.2
42.2
42.2
42.2
42.2
42.2
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
91
140
213
109
161
186
263
127
202
272
181
281
345
247
534
753
91
118
103
154
229
127
172
211
281
147
218
288
108
136
121
177
252
152
195
236
306
141
163
152
222
281
13-19
13-19
13-19
13-19
14-22
14-22
14-22
16-25
16-25
35.1
35.1
35.1
35.1
38.1
38.1
38.1
38.1
38.1
42.2
42.2
42.2
42.2
42.2
42.2
42.2
52.5
52.5
109
159
188
254
127
202
268
177
281
All Rights Reserved
M30S16L
M30S16M
M30S16H
M30S18L
M30S18M
M30S18H
M30S20L
M30S20M
M30S20H
M30S24L
M30S24M
M30S24H
M30D14L
M30D14LM
M30D14M
M30D 14H
M30D16L
M30D16M
M30D 16H
M30D18L
M30D18M
M30D 18H
M30T 12L
M30T 12M
2011598
2011607
2011613
2011616
2011625
2011629
2011631
2011634
2011638
2011639
2011640
2011641
2011643
2011659
2011652
2011658
2011661
2011670
2011672
2011675
2011676
2011677
2011679
2011680
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
lk
380B
A
Overall
Len gth
(mm)
1125
1173
1173
1173
1275
1275
1275
790
790
790
848
848
848
848
905
905
905
1003
1003
1003
749
749
794
794
794
851
851
851
851
908
908
908
1004
1004
1004
748
748
792
792
792
849
849
849
849
B
Net
Length
(mm )
929
976
976
976
1078
1078
1078
714
714
714
772
772
772
772
829
829
829
927
927
927
673
673
718
718
718
775
775
775
775
832
832
832
929
929
929
672
672
716
716
716
773
773
773
773
1103
1103
1103
1168
1168
1168
1257
1257
1257
1359
1359
1359
952
952
952
952
1009
1009
1009
1048
1048
1048
895
895
917
917
917
955
955
955
1044
1044
1044
1145
1145
1145
860
860
860
860
917
917
917
955
955
955
802
802
All Rights Reserved
E
F
ThickWid th
n ess
(mm )
(mm)
329
578
174
629
288
629
390
629
174
730
371
730
472
730
148
406
263
406
364
406
148
457
197
457
274
457
387
457
148
514
260
514
323
514
174
578
279
578
329
578
208
356
289
356
208
406
322
406
424
406
208
457
259
457
332
457
445
457
208
514
318
514
382
514
252
578
356
578
407
578
265
356
346
356
265
406
379
406
481
406
265
457
316
457
391
457
503
457
27 TON NES
148
514
260
514
323
514
174
578
279
578
329
578
174
629
288
629
390
629
174
730
371
730
472
730
148
457
199
457
274
457
387
457
148
514
260
514
323
514
174
578
279
578
329
578
208
406
322
406
H
J
Throat
Openin g Hoo k
T hickWith
Flapp er ness
(m m)
(mm)
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
70.0
75.5
82.5
82.5
82.5
82.5
82.5
82.5
82.5
82.5
82.5
82.5
82.5
82.5
82.5
82.5
82.5
82.5
82.5
82.5
82.5
82.5
82.5
82.5
82.5
82.5
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
Dead End ‡
K
Hoo k
Width
(mm)
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
Std.
Wire
Line
Sizes
(m m)*
16-25
19-28
19-28
19-28
22-32
22-32
22-32
13-19
13-19
13-19
13-19
13-19
13-19
13-19
14-22
14-22
14-22
16-25
16-25
16-25
11-16
11-16
13-19
13-19
13-19
13-19
13-19
13-19
13-19
14-22
14-22
14-22
16-25
16-25
16-25
11-16
11-16
13-19
13-19
13-19
13-19
13-19
13-19
13-19
T
T hickness
(m m)
38.1
38.1
38.1
38.1
38.1
38.1
38.1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
U
Pin
Hole
(mm )
52.5
52.5
52.5
52.5
52.5
52.5
52.5
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Weight
Each
(kg.)
345
197
297
364
247
535
753
103
154
229
127
159
211
277
147
218
288
213
320
381
108
136
121
177
245
152
225
236
306
176
252
318
265
365
426
141
168
152
206
281
193
220
273
340
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
14-22
14-22
14-22
16-25
16-25
16-25
19-28
19-28
19-28
22-32
22-32
22-32
13-19
13-19
13-19
13-19
14-22
14-22
14-22
16-25
16-25
16-25
13-19
13-19
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
—
—
—
—
—
—
—
—
—
—
—
—
42.2
42.2
42.2
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
—
—
—
—
—
—
—
—
—
—
—
—
138
211
281
191
290
351
212
347
508
336
640
857
135
172
218
293
159
230
297
222
322
383
145
201
239
McKissick®
Blocks
Mo del
No.
M25S18H
M25S20L
M25S20M
M25S20H
M25S24L
M25S24M
M25S24H
M25D12L
M25D12M
M25D 12H
M25D14L
M25D14LM
M25D14M
M25D 14H
M25D16L
M25D16M
M25D 16H
M25D18L
M25D18M
M25D 18H
M25T 10L
M25T 10M
M25T 12L
M25T 12M
M25T12H
M25T 14L
M25T14LM
M25T 14M
M25T14H
M25T 16L
M25T 16M
M25T16H
M25T 18L
M25T 18M
M25T18H
M25Q10L
M25Q10M
M25Q12L
M25Q12M
M25Q12H
M25Q14L
M25Q14LM
M25Q14H
M25Q14M
Inquiry
Stock
No.
2011467
2011458
2011459
2011460
2011464
2011465
2011466
2011468
2011469
2011470
2011472
2011481
2011490
2011495
2011499
2011508
2011512
2011576
2011579
2011581
2011514
2011515
2011517
2011526
2011531
2011535
2011540
2011544
2011553
2011562
2011571
2011575
2011578
2011580
2011587
2011588
2011589
2011590
2011591
2011592
2011593
2011596
2011594
2011595
Working
Load
Limit
(t) †
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
23@
Mo del
No.
M30T12H
M30T14L
M30T14LM
M30T14M
M30T14H
M30T16L
M30T16M
M30T16H
M30T18L
M30T18M
M30T18H
M30T20L
M30T20M
M30T20H
M30Q10L
M30Q10M
M30Q12L
M30Q12M
M30Q12H
M30Q14L
M30Q14LM
M30Q14M
M30Q14H
M30Q16L
M30Q16M
M30Q16H
Inquiry
Stock
No.
2011681
2011688
2011703
2011697
2011702
2011706
2011708
2011710
2011712
2011715
2011719
2011742
2011743
2011744
2011714
2011716
2011717
2011718
2011720
2011724
2011741
2011733
2011737
2011738
2011739
2011740
Working
Load
Limit
(t) †
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
M35S18L
M35S18M
M35S18H
M35S20L
M35S20M
M35S20H
M35S24L
M35S24M
M35S24H
M35D16L
M35D16M
M35D16H
M35D18L
M35D18M
M35D18H
M35T14L
M35T14LM
M35T14M
M35T14H
M35T16L
M35T16M
M35T16H
M35T18L
M35T18M
M35T18H
M35T20L
M35T20M
M35T20H
M35Q12L
M35Q12M
M35Q12H
M35Q14L
M35Q14LM
M35Q14M
M35Q14H
M35Q16L
M35Q16M
M35Q16H
M35QN14L
M35QN14LM
M35QN14M
M35QN14H
2011745
2011746
2011747
2011748
2011751
2011755
2011752
2011753
2011754
2011756
2011757
2011758
2011760
2011769
2011774
2011778
2011792
2011787
2011793
2011794
2011795
2011796
2011797
2011799
2011802
2011798
2011800
2011801
2011803
2011804
2011805
2011806
2011807
2011814
2011817
2011818
2011819
2011820
2011815
2011808
2011809
2011810
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
32
lk
380B
240
A
Overall
Len gth
(mm)
895
953
953
953
953
1010
1010
1010
1048
1048
1048
1099
1099
1099
851
851
895
895
895
953
953
953
953
1010
1010
1010
B
Net
Leng th
(mm )
802
860
860
860
860
917
917
917
955
955
955
1006
1006
1006
758
758
802
802
802
860
860
860
860
917
917
917
1270
1270
1270
1359
1359
1359
1461
1461
1461
1111
1111
1111
1047
1047
1047
1056
1056
1056
1056
1113
1113
1113
1149
1149
1149
1238
1238
1238
998
998
998
1056
1056
1056
1056
1113
1113
1113
1143
1143
1143
1143
1034
1034
1034
1122
1130
1122
1224
1224
1224
995
995
995
955
955
955
938
938
938
938
995
995
995
1034
1034
1034
1122
1122
1122
881
881
881
938
938
938
938
995
995
995
938
938
938
938
H
J
Throat
E
Openin g Hoo k
F
Th ickT hickWith
n ess
(mm )
(mm)
(mm)
(mm)
424
406
82.5
92.0
208
457
82.5
92.0
257
457
82.5
92.0
332
457
82.5
92.0
445
457
82.5
92.0
208
514
82.5
92.0
318
514
82.5
92.0
382
514
82.5
92.0
252
578
82.5
92.0
356
578
82.5
92.0
407
578
82.5
92.0
252
629
82.5
92.0
366
629
82.5
92.0
468
629
82.5
92.0
265
356
82.5
92.0
346
356
82.5
92.0
265
406
82.5
92.0
379
406
82.5
92.0
481
406
82.5
92.0
265
457
82.5
92.0
316
457
82.5
92.0
392
457
82.5
92.0
505
457
82.5
92.0
265
514
82.5
92.0
378
514
82.5
92.0
441
514
82.5
92.0
32 TONNES
174
578
76.0
116
279
578
76.0
116
329
578
76.0
116
174
629
76.0
116
288
629
76.0
116
390
629
76.0
116
174
730
76.0
116
371
730
76.0
116
472
730
76.0
116
174
514
76.0
116
285
514
76.0
116
348
514
76.0
116
252
578
76.0
116
356
578
76.0
116
407
578
76.0
116
208
457
76.0
116
259
457
76.0
116
332
457
76.0
116
445
457
76.0
116
208
514
76.0
116
318
514
76.0
116
382
514
76.0
116
252
578
76.0
116
356
578
76.0
116
407
578
76.0
116
252
629
76.0
116
366
629
76.0
116
468
629
76.0
116
265
406
76.0
116
379
406
76.0
116
481
406
76.0
116
265
457
76.0
116
316
457
76.0
116
392
457
76.0
116
505
457
76.0
116
265
514
76.0
116
378
514
76.0
116
441
514
76.0
116
337
457
76.0
116
387
457
76.0
116
464
457
76.0
116
500
457
76.0
116
Dead End ‡
K
Hoo k
Width
(mm)
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
Std.
Wire
Line
Sizes
(mm)*
13-19
13-19
13-19
13-19
13-19
14-22
14-22
14-22
16-25
16-25
16-25
19-28
19-28
19-28
11-16
11-16
13-19
13-19
13-19
13-19
13-19
13-19
13-19
14-22
14-22
14-22
T
T hickness
(m m)
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
U
Pin
Hole
(mm )
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
16-25
16-25
16-25
19-28
19-28
19-28
22-32
22-32
22-32
14-22
14-22
14-22
16-25
16-25
16-25
13-19
13-19
13-19
13-19
14-22
14-22
14-22
16-25
16-25
16-25
19-28
19-28
19-28
13-19
13-19
13-19
13-19
13-19
13-19
13-19
14-22
14-22
14-22
13-19
13-19
13-19
13-19
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
31.8
31.8
31.8
31.8
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
35.8
35.8
35.8
35.8
Weight
Each
(kg.)
270
177
218
261
337
206
277
342
281
388
449
312
449
608
159
184
168
225
297
206
236
290
362
195
265
332
272
332
392
244
379
536
336
640
857
195
265
332
254
365
424
204
245
286
357
227
303
365
308
408
469
338
479
635
199
252
322
206
236
294
370
265
340
404
240
281
367
435
All Rights Reserved
M40S20L
M40S20M
M40S20H
M40S24L
M40S24M
M40S24H
M40D18L
M40D18M
M40D 18H
M40D20L
M40D20M
M40D 20H
M40T 14L
M40T 14M
M40T14H
M40T 16L
M40T 16M
M40T16H
M40T 18L
M40T 18M
M40T18H
M40T 20L
M40T 20M
M40T20H
M40Q14L
M40Q14M
M40Q14H
M40Q16L
M40Q16M
M40Q16H
M40Q18L
M40Q18M
M40Q18H
M40QN14L
M40QN14M
M40QN14H
2011833
2011834
2011835
2011825
2011829
2011832
2011918
2011919
2011920
2011841
2011850
2011854
2011855
2011856
2011857
2011859
2011868
2011871
2011874
2011877
2011881
2011882
2011883
2011884
2011885
2011886
2011891
2011895
2011904
2011908
2011910
2011913
2011917
2011921
2011922
2011923
36
36
36
36
36
36
36
36
36
36
36
36
36
36
36
36
36
36
36
36
36
36
36
36
36
36
36
36
36
36
36
36
36
36
36
36
M45S24L
M45S24M
M45S24H
M45D20L
M45D20M
M45D 20H
M45T 16L
M45T 16M
M45T16H
M45T 18L
M45T 18M
M45T18H
M45T 20L
M45T 20M
M45T20H
M45Q14L
M45Q14M
M45Q14H
M45Q16L
M45Q16M
M45Q16H
M45Q18L
M45Q18M
M45Q18H
M45QN16L
M45QN16M
M45QN16H
2011924
2011925
2011926
2011928
2011931
2011937
2011942
2011951
2011960
2011969
2011978
2011987
2011993
2011996
2012000
2012001
2012003
2012004
2012005
2012006
2012007
2012008
2012009
2012010
2011997
2011998
2011999
40@
40@
40@
40@
40@
40@
40@
40@
40@
40@
40@
40@
40@
40@
40@
40@
40@
40@
40@
40@
40@
40@
40@
40@
40@
40@
40@
M50S24L
M50S24M
M50S24H
2012015
2012016
2012017
45
45
45
lk
380B
A
Overall
Len gth
(mm)
E
F
ThickWid th
n ess
(mm )
(mm)
36 TON NES
1418
1168
198
629
76.0
1418
1168
313
629
76.0
1418
1168
414
629
86.0
1519
1270
198
730
86.0
1519
1270
395
730
86.0
1519
1270
497
730
86.0
1208
1080
198
578
86.0
1208
1080
303
578
86.0
1208
1080
354
578
86.0
1272
1143
198
629
86.0
1272
1143
313
629
86.0
1272
1143
414
629
86.0
1103
975
208
457
86.0
1103
975
332
457
86.0
1103
975
445
457
86.0
1161
1032
208
514
86.0
1161
1032
318
514
86.0
1161
1032
382
514
86.0
1202
1073
264
578
86.0
1202
1073
368
578
86.0
1202
1073
419
578
86.0
1272
1143
264
629
86.0
1272
1143
378
629
86.0
1272
1143
480
629
86.0
1103
975
265
457
86.0
1103
975
392
457
86.0
1103
975
429
457
86.0
1161
1032
265
514
86.0
1161
1032
378
514
86.0
1161
1032
441
514
86.0
1202
1073
338
578
86.0
1202
1073
443
578
86.0
1202
1073
494
578
86.0
1194
988
337
457
86.0
1194
988
464
457
86.0
1194
988
500
457
86.0
40 T ONNES @ - Ultimate Load is 3.6 times the Working
1519
1270
198
730
86.0
1519
1270
395
730
86.0
1519
1270
497
730
86.0
1272
1143
198
629
86.0
1272
1143
313
629
86.0
1272
1143
414
629
86.0
1161
1032
208
514
86.0
1161
1032
318
514
86.0
1161
1032
382
514
86.0
1202
1073
264
578
86.0
1202
1073
368
578
86.0
1202
1073
419
578
86.0
1272
1143
264
629
86.0
1272
1143
378
629
86.0
1272
1143
480
629
86.0
1103
975
265
457
86.0
1103
975
392
457
86.0
1103
975
429
457
86.0
1161
1032
265
514
86.0
1161
1032
378
514
86.0
1161
1032
441
514
86.0
1202
1073
338
578
86.0
1202
1073
443
578
86.0
1202
1073
494
578
86.0
1249
1032
337
514
86.0
1249
1032
448
514
86.0
1249
1032
511
514
86.0
45 TON NES
1629
1349
198
730
105
1629
1349
395
730
105
1629
1349
497
730
105
All Rights Reserved
B
Net
Length
(mm )
H
J
Throat
Openin g Hoo k
T hickWith
Flapp er ness
(m m)
(mm)
Dead End ‡
K
Hoo k
Width
(mm)
Std.
Wire
Line
Sizes
(m m)*
T
T hickness
(m m)
U
Pin
Hole
(mm )
Weight
Each
(kg.)
116
116
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
Load Limit
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
92.0
92.0
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
19-28
19-28
19-28
22-32
22-32
22-32
16-25
16-25
16-25
19-28
19-28
19-28
13-19
13-19
13-19
14-22
14-22
14-22
16-25
16-25
16-25
19-28
19-28
19-28
13-19
13-19
13-19
14-22
14-22
14-22
16-25
16-25
16-25
13-19
13-19
13-19
44.5
44.5
44.5
44.5
44.5
44.5
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
31.8
31.8
31.8
58.0
58.0
58.0
58.0
58.0
58.0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
35.8
35.8
35.8
299
433
589
358
671
880
311
420
487
344
494
635
235
315
382
238
313
379
362
462
525
403
538
694
243
338
413
284
356
422
422
522
585
231
333
408
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
22-32
22-32
22-32
19-28
19-28
19-28
14-22
14-22
14-22
16-25
16-25
16-25
19-28
19-28
19-28
13-19
13-19
13-19
14-22
14-22
14-22
16-25
16-25
16-25
14-22
14-22
14-22
44.5
44.5
44.5
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
31.8
31.8
31.8
58.0
58.0
58.0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
36.6
36.6
36.6
365
655
880
344
479
635
238
313
379
362
462
525
403
538
694
243
338
413
284
356
422
422
522
585
302
373
439
152
152
152
113
113
113
22-32
22-32
22-32
51.0
51.0
51.0
64.5
64.5
64.5
435
710
941
241
McKissick®
Blocks
Mo del
No.
Inquiry
Stock
No.
Working
Load
Limit
(t) †
Mo del
No.
M50D24L
M50D24M
M50D24H
M50T18L
M50T18M
M50T18H
M50T20L
M50T20M
M50T20H
M50T24L
M50T24M
M50T24H
M50Q16L
M50Q16M
M50Q16H
M50Q18L
M50Q18M
M50Q18H
M50Q20L
M50Q20M
M50Q20H
M50QN14L
M50QN14M
M50QN14H
M50QN16L
M50QN16M
M50QN16H
M50SX14L
M,50SX14M
M50SX14H
Inquiry
Stock
No.
2012018
2012019
2012020
2012014
2012023
2012027
2012032
2012041
2012045
2012048
2012050
2012055
2012059
2012068
2012073
2012077
2012086
2012091
2012095
2012097
2012101
2012056
2012057
2012058
2012060
2012061
2012062
2012063
2012064
2012065
Working
Load
Limit
(t) †
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
M55S24L
M55S24M
M55S24H
M55D24L
M55D24M
M55D24H
M55T18L
M55T18M
M55T18H
M55T20L
M55T20M
M55T20H
M55T24L
M55T24M
M55T24H
M55Q16L
M55Q16M
M55Q16H
M55Q18L
M55Q18M
M55Q18H
M55Q20L
M55Q20M
M55Q20H
M55QN14L
M55QN14M
M55QN14H
M55QN16L
M55QN16M
M55QN16H
M55QN18L
M55QN18M
M55QN18H
M55SX14L
M55SX14M
M55SX14H
2012105
2012106
2012107
2012108
2012109
2012110
2012104
2012113
2012122
2012111
2012114
2012123
2012112
2012124
2012125
2012131
2012140
2012143
2012146
2012149
2012153
2012171
2012172
2012173
2012126
2012127
2012128
2012158
2012167
2012170
2012147
2012150
2012154
2012135
2012141
2012144
M60D24L
2012175
lk
380B
242
A
Overall
Len gth
(mm)
1502
1502
1502
1362
1362
1362
1375
1375
1375
1502
1502
1502
1267
1267
1267
1362
1362
1362
1375
1375
1375
1314
1314
1314
1372
1372
1372
1314
1314
1314
B
Net
Leng th
(mm )
1349
1349
1349
1210
1210
1210
1222
1222
1222
1349
1349
1349
1115
1115
1115
1286
1286
1286
1223
1223
1223
1064
1064
1064
1115
1115
1115
1064
1064
1064
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
1629
1629
1629
1502
1502
1502
1362
1362
1362
1375
1375
1375
1502
1502
1502
1267
1267
1267
1362
1362
1362
1375
1375
1375
1314
1314
1314
1372
1372
1372
1489
1489
1489
1314
1314
1314
1349
1349
1349
1349
1349
1349
1210
1210
1210
1222
1222
1222
1349
1349
1349
1115
1115
1115
1286
1286
1286
1222
1222
1222
1064
1064
1064
1115
1115
1115
1210
1210
1210
1064
1064
1064
54
1502
1349
H
J
Throat
E
Openin g Hoo k
F
Th ickT hickWith
n ess
(mm )
(mm)
(mm)
(mm)
198
730
105
152
395
730
105
152
497
730
105
152
264
578
105
152
368
578
105
152
419
578
105
152
264
629
105
152
378
629
105
152
480
629
105
152
264
730
105
152
461
730
105
152
562
730
105
152
338
514
105
152
449
514
105
152
513
514
105
152
338
578
105
152
443
578
105
152
494
578
105
152
338
629
105
152
452
629
105
152
554
629
105
152
337
457
105
152
462
457
105
152
575
457
105
152
337
514
105
152
448
514
105
152
511
514
105
152
394
457
105
152
521
457
105
152
633
457
105
152
50 TONNES
198
730
105
152
395
730
105
152
497
730
105
152
198
730
105
152
395
730
105
152
497
730
105
152
264
578
105
152
368
578
105
152
419
578
105
152
264
629
105
152
378
629
105
152
480
629
105
152
264
730
105
152
461
730
105
152
562
730
105
152
338
514
105
152
449
514
105
152
513
514
105
152
338
578
105
152
443
578
105
152
494
578
105
152
338
629
105
152
452
629
105
152
579
629
105
152
337
457
105
152
464
457
105
152
575
457
105
152
337
514
105
152
448
514
105
152
511
514
105
152
445
578
105
152
549
578
105
152
600
578
105
152
394
457
105
152
520
457
105
152
633
457
105
152
54 TONNES
198
730
105
152
Dead End ‡
K
Hoo k
Width
(mm)
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
Std.
Wire
Line
Sizes
(mm)*
22-32
22-32
22-32
16-25
16-25
16-25
19-28
19-28
19-28
22-32
22-32
22-32
14-22
14-22
14-22
16-25
16-25
16-25
19-28
19-28
19-28
13-19
13-19
13-19
14-22
14-22
14-22
13-19
13-19
13-19
T
T hickness
(m m)
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
U
Pin
Hole
(mm )
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
35.8
35.8
35.8
35.8
35.8
35.8
35.8
35.8
35.8
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
22-32
22-32
22-32
22-32
22-32
22-32
16-25
16-25
16-25
19-28
19-28
19-28
22-32
22-32
22-32
14-22
14-22
14-22
16-25
16-25
16-25
19-28
19-28
19-28
13-19
13-19
13-19
14-22
14-22
14-22
16-25
16-25
16-25
13-19
13-19
13-19
51.0
51.0
51.0
—
—
—
—
—
—
—
—
—
—
—
—
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
64.5
64.5
64.5
—
—
—
—
—
—
—
—
—
—
—
—
35.8
35.8
35.8
35.8
35.8
35.8
35.8
35.8
35.8
35.8
35.8
35.8
435
723
941
517
803
1021
399
499
562
449
587
742
544
857
1074
369
445
510
451
553
617
517
676
841
381
469
538
397
467
535
626
726
794
420
463
567
113
22-32
-
-
517
Weight
Each
(kg.)
517
803
1021
422
499
562
449
587
742
544
857
1074
369
445
510
451
553
617
517
676
853
365
435
538
397
467
535
420
463
567
All Rights Reserved
M65D24L
M65D24M
M65D 24H
M65T 18L
M65T 18M
M65T18H
M65T 20L
M65T 20M
M65T20H
M65T 24L
M65T 24M
M65T24H
M65Q16L
M65Q16M
M65Q16H
M65Q18L
M65Q18M
M65Q18H
M65Q20L
M65Q20M
M65Q20H
M65Q24L
M65Q24M
M65Q24H
M65QN16L
M65QN16M
M65QN16H
M65QN18L
M65QN18M
M65QN18H
M65QN20L
M65QN20M
M65QN20H
M65QN24L
M65QN24M
M65QN24H
2012376
2012377
2012378
2012304
2012305
2012306
2012307
2012311
2012315
2012316
2012317
2012318
2012312
2012313
2012314
2012340
2012341
2012342
2012319
2012323
2012327
2012328
2012329
2012330
2012331
2012335
2012339
2012343
2012347
2012351
2012355
2012359
2012363
2012364
2012368
2012372
59
59
59
59
59
59
59
59
59
59
59
59
59
59
59
59
59
59
59
59
59
59
59
59
59
59
59
59
59
59
59
59
59
59
59
59
lk
380B
A
Overall
Len gth
(mm)
1502
1502
1362
1362
1362
1375
1375
1375
1502
1502
1502
1267
1267
1267
1362
1362
1362
1375
1375
1375
1502
1502
1502
1502
1502
1502
1314
1314
1314
1489
1489
1489
B
Net
Length
(mm )
1349
1349
1210
1210
1210
1222
1222
1222
1349
1349
1349
1115
1115
1115
1210
1210
1210
1222
1222
1222
1349
1349
1349
1222
1222
1222
1162
1162
1162
1210
1210
1210
1502
1502
1502
1362
1362
1362
1375
1375
1375
1502
1502
1502
1267
1267
1267
1362
1362
1362
1375
1375
1375
1502
1502
1502
1445
1445
1445
1489
1489
1489
1502
1502
1502
1591
1591
1591
1349
1349
1349
1210
1210
1210
1222
1222
1222
1349
1349
1349
1115
1115
1115
1210
1210
1210
1222
1222
1222
1349
1349
1349
1165
1165
1165
1210
1210
1210
1222
1222
1222
1311
1311
1311
All Rights Reserved
E
F
ThickWid th
n ess
(mm )
(mm)
313
730
497
730
264
578
368
578
419
578
264
629
378
629
480
629
262
730
460
730
559
730
338
514
449
514
513
514
338
578
443
578
494
578
338
629
452
629
554
629
338
730
535
730
637
730
445
629
559
629
660
629
394
457
520
457
631
457
496
578
601
578
652
578
59 TON NES
198
730
395
730
497
730
264
578
368
578
419
578
264
629
378
629
480
629
264
730
460
730
562
730
338
514
449
514
513
514
338
578
443
578
494
578
338
629
452
629
554
629
338
730
535
730
637
730
445
514
556
514
619
514
445
578
549
578
600
578
445
629
559
629
660
629
445
730
641
730
743
730
H
J
Throat
Openin g Hoo k
T hickWith
Flapp er ness
(m m)
(mm)
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
152
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
Dead End ‡
K
Hoo k
Width
(mm)
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
Std.
Wire
Line
Sizes
(m m)*
22-32
22-32
16-25
16-25
16-25
19-28
19-28
19-28
22-32
22-32
22-32
14-22
14-22
14-22
16-25
16-25
16-25
19-28
19-28
19-28
22-32
22-32
22-32
19-28
19-28
19-28
13-19
13-19
13-19
16-25
16-25
16-25
T
T hickness
(m m)
38.1
38.1
38.1
31.8
31.8
31.8
38.1
38.1
38.1
U
Pin
Hole
(mm )
35.8
35.8
35.8
35.8
35.8
35.8
52.5
52.5
52.5
Weight
Each
(kg.)
803
1021
400
506
562
431
603
769
569
857
1073
411
467
553
454
557
620
517
676
841
659
962
1179
710
844
1002
420
499
567
640
748
816
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
22-32
22-32
22-32
16-25
16-25
16-25
19-28
19-28
19-28
22-32
22-32
22-32
14-22
14-22
14-22
16-25
16-25
16-25
19-28
19-28
19-28
22-32
22-32
22-32
14-22
14-22
14-22
16-25
16-25
16-25
19-28
19-28
19-28
22-32
22-32
22-32
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
35.8
35.8
35.8
35.8
35.8
35.8
35.8
35.8
35.8
35.8
35.8
35.8
517
803
1021
422
499
590
451
590
742
569
857
1073
411
467
553
481
551
649
517
676
841
659
962
1179
401
475
544
626
726
793
710
844
1002
831
1150
1360
243
McKissick®
Blocks
Mo del
No.
M60D24M
M60D 24H
M60T 18L
M60T 18M
M60T18H
M60T 20L
M60T 20M
M60T20H
M60T 24L
M60T 24M
M60T24H
M60Q16L
M60Q16M
M60Q16H
M60Q18L
M60Q18M
M60Q18H
M60Q20L
M60Q20M
M60Q20H
M60Q24L
M60Q24M
M60Q24H
M60QN20L
M60QN20M
M60QN20H
M60SX14L
M60SX14M
M60SX14H
M60SX18L
M60SX18M
M60SX18H
Inquiry
Stock
No.
2012179
2012183
2012187
2012191
2012195
2012199
2012203
2012207
2012211
2012215
2012219
2012223
2012227
2012231
2012235
2012239
2012243
2012247
2012251
2012255
2012259
2012263
2012267
2012271
2012275
2012279
2012283
2012287
2012291
2012295
2012299
2012303
Working
Load
Limit
(t) †
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
54
Mo del
No.
M65SX16L
M65SX16M
M65SX16H
M65SX18L
M65SX18M
M65SX18H
M65SX20L
M65SX20M
M65SX20H
Inquiry
Stock
No.
2012352
2012353
2012354
2012356
2012357
2012358
2012367
2012371
2012375
Working
Load
Limit
(t) †
59
59
59
59
59
59
59
59
59
M70D24L
M70D24M
M70D24H
M70T18L
M70T18M
M70T18H
M70T20L
M70T20M
M70T20H
M70T24L
M70T24M
M70T24H
M70Q16L
M70Q16M
M70Q16H
M70Q18L
M70Q18M
M70Q18H
M70Q20L
M70Q20M
M70Q20H
M70Q24L
M70Q24M
M70Q24H
M70QN16L
M70QN16M
M70QN16H
M70QN18L
M70QN18M
M70QN18H
M70QN20L
M70QN20M
M70QN20H
M70QN24L
M70QN24M
M70QN24H
M70SX16L
M70SX16M
M70SX16H
M70SX18L
M70SX18M
M70SX18H
M70SX20L
M70SX20M
M70SX20H
2012379
2012383
2012387
2012391
2012395
2012399
2012403
2012407
2012411
2012415
2012419
2012423
2012427
2012431
2012435
2012439
2012443
2012447
2012451
2012455
2012459
2012463
2012467
2012471
2012475
2012479
2012483
2012487
2012491
2012495
2012499
2012503
2012507
2012511
2012515
2012519
2012523
2012527
2012531
2012535
2012539
2012543
2012547
2012551
2012555
M75D24L
M75D24M
M75D24H
M75T20L
M75T20M
M75T20H
M75T24L
M75T24M
M75T24H
M75Q16L
M75Q16M
M75Q16H
M75Q18L
2012559
2012563
2012567
2012571
2012575
2012579
2012583
2012587
2012591
2012596
2012600
2012604
2012595
lk
380B
244
A
Overall
Len gth
(mm)
1445
1445
1445
1489
1489
1489
1502
1502
1502
B
Net
Leng th
(mm )
1165
1165
1165
1210
1210
1210
1222
1222
1222
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
1637
1637
1637
1497
1497
1497
1548
1548
1548
1637
1637
1637
1453
1453
1453
1497
1497
1497
1548
1548
1548
1637
1637
1637
1640
1640
1640
1608
1608
1608
1675
1675
1675
1764
1764
1764
1564
1564
1564
1624
1624
1624
1675
1675
1675
1467
1467
1467
1327
1327
1327
1378
1378
1378
1467
1467
1467
1283
1283
1283
1327
1327
1327
1378
1378
1378
1467
1467
1467
1283
1283
1283
1327
1327
1327
1378
1378
1378
1467
1467
1467
1283
1283
1283
1327
1327
1327
1378
1378
1378
68
68
68
68
68
68
68
68
68
68
68
68
68
1637
1637
1637
1548
1548
1548
1637
1637
1637
1453
1453
1453
1497
1467
1467
1467
1378
1378
1378
1467
1467
1467
1283
1283
1283
1327
H
J
Throat
E
Openin g Hoo k
F
Th ickT hickWith
n ess
(mm )
(mm)
(mm)
(mm)
496
514
105
152
607
514
105
152
671
514
105
152
496
578
105
152
601
578
105
152
652
578
105
152
496
629
105
152
610
629
105
152
712
629
105
152
63 TONNES
282
730
137
170
479
730
137
170
580
730
137
170
282
578
137
170
387
578
137
170
438
578
137
170
282
629
137
170
397
629
137
170
489
629
137
170
282
730
137
170
480
730
137
170
581
730
137
170
338
514
137
170
449
514
137
170
514
514
137
170
338
578
137
170
443
578
137
170
494
578
137
170
338
629
137
170
452
629
137
170
554
629
137
170
338
730
137
170
535
730
137
170
637
730
137
170
464
514
137
170
575
514
137
170
638
514
137
170
464
578
137
170
568
578
137
170
619
578
137
170
464
629
137
170
578
629
137
170
679
629
137
170
464
730
137
170
660
730
137
170
762
730
137
170
518
514
137
170
629
514
137
170
693
514
137
170
518
578
137
170
623
578
137
170
674
578
137
170
518
629
137
170
633
629
137
170
734
629
137
170
68 TONNES
282
730
137
170
479
730
137
170
580
730
137
170
282
629
137
170
397
629
137
170
498
629
137
170
282
730
137
170
480
730
137
170
581
730
137
170
338
514
137
170
449
514
137
170
513
514
137
170
338
578
137
170
Dead End ‡
K
Hoo k
Width
(mm)
113
113
113
113
113
113
113
113
113
Std.
Wire
Line
Sizes
(mm)*
14-22
14-22
14-22
16-25
16-25
16-25
19-28
19-28
19-28
T
T hickness
(m m)
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
U
Pin
Hole
(mm )
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
22-32
22-32
22-32
16-25
16-25
16-25
19-28
19-28
19-28
22-32
22-32
22-32
14-22
14-22
14-22
16-25
16-25
16-25
19-28
19-28
19-28
22-32
22-32
22-32
14-22
14-22
14-22
16-25
16-25
16-25
19-28
19-28
19-28
22-32
22-32
22-32
14-22
14-22
14-22
16-25
16-25
16-25
19-28
19-28
19-28
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
42.2
42.2
42.2
42.2
42.2
42.2
52.5
52.5
52.5
52.5
52.5
52.5
42.2
42.2
42.2
52.5
52.5
52.5
52.5
52.5
52.5
690
993
1211
572
680
748
641
776
935
745
1040
1257
533
608
676
590
699
766
651
786
945
779
1082
1300
608
683
751
760
860
949
857
991
1151
1012
1315
1533
700
776
844
869
968
1036
914
1048
1208
108
108
108
108
108
108
108
108
108
108
108
108
108
22-32
22-32
22-32
19-28
19-28
19-28
22-32
22-32
22-32
14-22
14-22
14-22
16-25
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
690
993
1211
641
776
935
737
1039
1257
533
608
676
590
Weight
Each
(kg.)
531
606
674
640
748
816
737
871
1031
All Rights Reserved
M80D24L
M80D24M
M80D 24H
M80T 20L
M80T 20M
M80T20H
M80T 24L
M80T 24M
M80T24H
M80Q16L
M80Q16M
M80Q16H
M80Q18L
M80Q18M
M80Q18H
M80Q20L
M80Q20M
M80Q20H
M80Q24L
M80Q24M
M80Q24H
M80QN16L
M80QN16M
M80QN16H
M80QN18L
M80QN18M
M80QN18H
M80QN20L
M80QN20M
M80QN20H
M80QN24L
M80QN24M
M80QN24H
M80SX16L
M80SX16M
M80SX16H
M80SX18L
M80SX18M
M80SX18H
2012691
2012695
2012699
2012703
2012707
2012711
2012715
2012719
2012723
2012727
2012731
2012735
2012739
2012743
2012747
2012751
2012755
2012759
2012763
2012767
2012771
2012775
2012779
2012783
2012787
2012791
2012795
2012799
2012803
2012807
2012811
2012815
2012819
2012823
2012827
2012831
2012835
2012839
2012843
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
lk
380B
A
Overall
Len gth
(mm)
1497
1497
1548
1548
1548
1637
1637
1637
1564
1564
1564
1608
1608
1608
1675
1675
1675
1637
1637
1637
1564
1564
1564
1624
1624
1624
1675
1675
1675
B
Net
Length
(mm )
1327
1327
1378
1378
1378
1467
1467
1467
1283
1283
1283
1327
1327
1327
1378
1378
1378
1467
1467
1467
1283
1283
1283
1327
1327
1327
1378
1378
1378
1637
1637
1637
1548
1548
1548
1637
1637
1637
1453
1453
1453
1497
1497
1497
1548
1548
1548
1637
1637
1637
1564
1564
1564
1608
1608
1608
1675
1675
1675
1764
1764
1764
1564
1564
1564
1624
1624
1624
1467
1467
1467
1378
1378
1378
1467
1467
1467
1283
1283
1283
1327
1327
1327
1378
1378
1378
1467
1467
1467
1283
1283
1283
1327
1327
1327
1378
1378
1378
1467
1467
1467
1283
1283
1283
1327
1327
1327
All Rights Reserved
E
F
ThickWid th
n ess
(mm )
(mm)
443
578
494
578
338
629
452
629
554
629
338
730
535
730
637
730
464
514
575
514
638
514
464
565
568
565
619
578
464
629
578
629
679
629
464
730
660
730
762
730
518
514
629
514
693
514
518
578
623
578
674
578
518
629
633
629
734
629
72 TON NES
282
730
479
730
580
730
282
629
397
629
498
629
282
730
480
730
581
730
338
514
449
514
513
514
338
578
443
578
494
578
338
629
452
629
554
629
338
730
535
730
637
730
464
514
575
514
638
514
464
578
568
578
619
578
464
629
578
629
679
629
464
730
660
730
762
730
518
514
629
514
693
514
518
578
623
578
674
578
H
J
Throat
Openin g Hoo k
T hickWith
Flapp er ness
(m m)
(mm)
137
170
137
170
137
170
137
170
137
170
137
170
137
170
137
170
137
170
137
170
137
170
137
170
137
170
137
170
137
170
137
170
137
170
137
170
137
170
137
170
137
170
137
170
137
170
137
170
137
170
137
170
137
170
137
170
137
170
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
137
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
170
Dead End ‡
K
Hoo k
Width
(mm)
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
Std.
Wire
Line
Sizes
(m m)*
16-25
16-25
19-28
19-28
19-28
22-32
22-32
22-32
14-22
14-22
14-22
16-25
16-25
16-25
19-28
19-28
19-28
22-32
22-32
22-32
14-22
14-22
14-22
16-25
16-25
16-25
19-28
19-28
19-28
T
T hickness
(m m)
—
—
—
—
—
—
—
—
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
U
Pin
Hole
(mm )
—
—
—
—
—
—
—
—
42.2
42.2
42.2
42.2
42.2
42.2
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
Weight
Each
(kg.)
699
766
651
786
945
779
1082
1300
608
644
751
760
860
927
857
991
1151
1012
1315
1533
700
776
844
869
968
1036
914
1048
1208
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
108
22-32
22-32
22-32
19-28
19-28
19-28
22-32
22-32
22-32
14-22
14-22
14-22
16-25
16-25
16-25
19-28
19-28
19-28
22-32
22-32
22-32
14-22
14-22
14-22
16-25
16-25
16-25
19-28
19-28
19-28
22-32
22-32
22-32
14-22
14-22
14-22
16-25
16-25
16-25
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
42.2
42.2
42.2
42.2
42.2
42.2
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
690
993
1211
641
776
935
737
1040
1257
533
608
676
590
699
766
651
786
945
779
1082
1300
608
683
751
760
860
927
857
991
1151
1012
1315
1533
700
776
844
869
968
1036
245
McKissick®
Blocks
Mo del
No.
M75Q18M
M75Q18H
M75Q20L
M75Q20M
M75Q20H
M75Q24L
M75Q24M
M75Q24H
M75QN16L
M75QN16M
M75QN16H
M75QN18L
M75QN18M
M75QN18H
M75QN20L
M75QN20M
M75QN20H
M75QN24L
M75QN24M
M75QN24H
M75SX16L
M75SX16M
M75SX16H
M75SX18L
M75SX18M
M75SX18H
M75SX20L
M75SX20M
M75SX20H
Inquiry
Stock
No.
2012599
2012603
2012607
2012611
2012615
2012619
2012623
2012627
2012631
2012635
2012639
2012632
2012636
2012640
2012643
2012647
2012651
2012655
2012659
2012663
2012668
2012672
2012676
2012667
2012671
2012675
2012679
2012683
2012687
Working
Load
Limit
(t) †
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
68
Mo del
No.
M80SX20L
M80SX20M
M80SX20H
Inquiry
Stock
No.
2012847
2012851
2012855
Working
Load
Limit
(t) †
72
72
72
M90T24L
M90T24M
M90T24H
M90Q20L
M90Q20M
M90Q20H
M90Q24L
M90Q24M
M90Q24H
M90QN18L
M90QN18M
M90QN18H
M90QN20L
M90QN20M
M90QN20H
M90QN24L
M90QN24M
M90QN24H
M90SX18L
M90SX18M
M90SX18H
M90SX20L
M90SX20M
M90SX20H
M90SX24L
M90SX24M
M90SX24H
2012859
2012863
2012867
2012871
2012875
2012879
2012883
2012887
2012891
2012904
2012908
2012912
2012895
2012899
2012903
2012907
2012911
2012915
2012919
2012923
2012927
2012931
2012935
2012939
2012943
2012947
2012952
M100T 24L
M100T 24M
M100T24H
M100Q20L
M100Q20M
M100Q20H
M100Q24L
M100Q24M
M100Q24H
M100QN18L
M100QN18M
M100QN18H
M100QN20L
M100QN20M
M100QN20H
M100QN24L
M100QN24M
M100QN24H
M100SX18L
M100SX18M
M100SX18H
M100SX20L
M100SX20M
M100SX20H
M100SX24L
M100SX24M
M100SX24H
M115Q24L
M115Q24M
M115Q24H
M115QN24L
M115QN24M
M115QN24H
M115SX18L
M115SX18M
M115SX18H
A
Overall
Len gth
(mm)
1675
1675
1675
B
Net
Leng th
(mm )
1378
1378
1378
81
81
81
81
81
81
81
81
81
81
81
81
81
81
81
81
81
81
81
81
81
81
81
81
81
81
81
1740
1740
1740
1626
1626
1626
1740
1740
1740
1702
1702
1702
1753
1753
1753
1854
1854
1854
1702
1702
1702
1753
1753
1753
1854
1854
1854
1522
1522
1522
1407
1407
1407
1522
1522
1522
1369
1369
1369
1407
1407
1407
1509
1509
1509
1357
1357
1357
1407
1407
1407
1509
1509
1509
2012860
2012864
2012868
2012967
2012971
2012975
2012979
2012983
2012987
2012991
2012995
2012999
2013003
2013007
2013011
2013015
2013019
2013023
2013027
2013031
2013035
2013039
2013043
2013047
2013051
2013055
2013059
90
90
90
90
90
90
90
90
90
90
90
90
90
90
90
90
90
90
90
90
90
90
90
90
90
90
90
1740
1740
1740
1626
1626
1626
1740
1740
1740
1702
1702
1702
1753
1753
1753
1854
1854
1854
1702
1702
1702
1753
1753
1753
1854
1854
1854
1522
1522
1522
1407
1407
1407
1522
1522
1522
1369
1369
1369
1407
1407
1407
1509
1509
1509
1357
1357
1357
1407
1407
1407
1509
1509
1509
2013075
2013079
2013083
2013087
2013091
2013095
2013099
2013103
2013107
104
104
104
104
104
104
104
104
104
1829
1829
1829
1962
1962
1962
1810
1810
1810
1597
1597
1597
1597
1597
1597
1445
1445
1445
lk
380B
246
H
J
Throat
E
Openin g Hoo k
F
Th ickT hickWith
n ess
(mm )
(mm)
(mm)
(mm)
518
629
137
170
633
629
137
170
734
629
137
170
81 TONNES
296
730
114
218
493
730
114
218
595
730
114
218
344
629
114
218
459
629
114
218
560
629
114
218
351
730
114
218
548
730
114
218
649
730
114
218
464
578
114
218
568
578
114
218
619
578
114
218
464
629
114
218
578
629
114
218
679
629
114
218
464
730
114
218
660
730
114
218
762
730
114
218
518
578
114
218
623
578
114
218
674
578
114
218
518
629
114
218
633
629
114
218
734
629
114
218
518
730
114
218
715
730
114
218
817
730
114
218
90 TONNES
296
730
114
218
493
730
114
218
595
730
114
218
344
629
114
218
459
629
114
218
560
629
114
218
351
730
114
218
548
730
114
218
649
730
114
218
464
578
114
218
568
578
114
218
619
578
114
218
464
629
114
218
578
629
114
218
679
629
114
218
464
730
114
218
660
730
114
218
762
730
114
218
518
578
114
218
623
578
114
218
674
578
114
218
518
629
114
218
633
629
114
218
734
629
114
218
518
730
114
218
715
730
114
218
817
730
114
218
104 TON NES
418
730
114
232
614
730
114
232
716
730
114
232
514
730
114
232
711
730
114
232
813
730
114
232
559
578
114
232
663
578
114
232
714
578
114
232
Dead End ‡
K
Hoo k
Width
(mm)
108
108
108
Std.
Wire
Line
Sizes
(mm)*
19-28
19-28
19-28
T
T hickness
(m m)
38.1
38.1
38.1
U
Pin
Hole
(mm )
52.5
52.5
52.5
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
22-32
22-32
22-32
19-28
19-28
19-28
22-32
22-32
22-32
16-25
16-25
16-25
19-28
19-28
19-28
22-32
22-32
22-32
16-25
16-25
16-25
19-28
19-28
19-28
22-32
22-32
22-32
—
—
—
—
—
—
—
—
—
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
—
—
—
—
—
—
—
—
—
58.0
58.0
58.0
58.0
58.0
58.0
58.0
58.0
58.0
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
876
1179
1397
807
941
1101
938
1225
1442
875
984
1051
927
1061
1221
1124
1427
1644
943
1043
1110
982
1117
1277
1186
1473
1692
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
22-32
22-32
22-32
19-28
19-28
19-28
22-32
22-32
22-32
16-25
16-25
16-25
19-28
19-28
19-28
22-32
22-32
22-32
16-25
16-25
16-25
19-28
19-28
19-28
22-32
22-32
22-32
—
—
—
—
—
—
—
—
—
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
—
—
—
—
—
—
—
—
—
58.0
58.0
58.0
58.0
58.0
58.0
58.0
58.0
58.0
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
876
1179
1397
807
941
1101
938
1225
1442
875
984
1051
927
1061
1221
1124
1427
1644
943
1043
1110
982
1117
1277
1186
1473
1692
152
152
152
152
152
152
152
152
152
22-32
22-32
22-32
22-32
22-32
22-32
16-25
16-25
16-25
44.5
44.5
44.5
44.5
44.5
44.5
64.5
64.5
64.5
64.5
64.5
64.5
1249
1535
1753
1506
1792
2009
1200
1309
1376
Weight
Each
(kg.)
914
1048
1208
All Rights Reserved
M125Q24L
M125Q24M
M125Q24H
M125QN24L
M125QN24M
M125QN24H
M125SX18L
M125SX18M
M125SX18H
M125SX20L
M125SX20M
M125SX20H
M125SX24L
M125SX24M
M125SX24H
2013135
2013139
2013143
2013147
2013151
2013155
2013159
2013163
2013167
2013171
2013175
2013179
2013183
2013187
2013188
M130Q24L
M130Q24M
M130Q24H
M130QN24L
M130QN24M
M130QN24H
M130SX18L
M130SX18M
M130SX18H
M130SX20L
M130SX20M
M130SX20H
M130SX24L
M130SX24M
M130SX24H
A
Overall
Len gth
(mm)
1861
1861
1861
1962
1962
1962
B
Net
Length
(mm )
1496
1496
1496
1597
1597
1597
113
113
113
113
113
113
113
113
113
113
113
113
113
113
113
1829
1829
1829
1962
1962
1962
1810
1810
1810
1861
1861
1861
1962
1962
1962
1597
1597
1597
1597
1597
1597
1445
1445
1445
1496
1496
1496
1597
1597
1597
2013192
2013196
2013200
2013191
2013195
2013199
2013203
2013207
2013211
2013218
2013219
2013223
2013227
2013231
2013235
117
117
117
117
117
117
117
117
117
117
117
117
117
117
117
1829
1829
1829
1962
1962
1962
1810
1810
1810
1861
1861
1861
1962
1962
1962
1597
1597
1597
1597
1597
1597
1445
1445
1445
1496
1496
1496
1597
1597
1597
M140Q24L
M140Q24M
M140Q24H
M140QN24L
M140QN24M
M140QN24H
M140SX18L
M140SX18M
M140SX18H
M140SX20L
M140SX20M
M140SX20H
M140SX24L
M140SX24M
M140SX24H
2013252
2013256
2013260
2013251
2013255
2013259
2013263
2013267
2013271
2013275
2013279
2013283
2013287
2013291
2013295
126
126
126
126
126
126
126
126
126
126
126
126
126
126
126
1829
1829
1829
1962
1962
1962
1810
1810
1810
1861
1861
1861
1962
1962
1962
1597
1597
1597
1597
1597
1597
1445
1445
1445
1496
1496
1496
1597
1597
1597
M150Q24L
M150Q24M
M150Q24H
M150QN24L
M150QN24M
M150QN24H
M150SX20L
M150SX20M
M150SX20H
M150SX24L
M150SX24M
M150SX24H
2013299
2013303
2013307
2013311
2013315
2013319
2013323
2013327
2013331
2013335
2013339
2013343
135
135
135
135
135
135
135
135
135
135
135
135
1829
1829
1829
1962
1962
1962
1861
1861
1861
1962
1962
1962
1597
1597
1597
1597
1597
1597
1496
1496
1496
1597
1597
1597
M165Q24L
2013347
149
1829
1597
lk
380B
All Rights Reserved
E
F
ThickWid th
n ess
(mm )
(mm)
559
629
673
629
775
629
560
730
756
730
858
730
113 TONN ES
418
730
614
730
716
730
514
730
711
730
813
730
559
578
663
578
714
578
559
629
673
629
775
629
560
730
756
730
858
730
117 TONN ES
418
730
614
730
716
730
514
730
711
730
813
730
559
578
663
578
714
578
559
629
673
629
775
629
560
730
756
730
858
730
126 TONN ES
418
730
614
730
716
730
514
730
711
730
813
730
559
578
663
578
714
578
559
629
673
629
775
629
560
730
756
730
858
730
135 TONN ES
418
730
614
730
716
730
559
730
756
730
857
730
559
629
673
629
775
629
560
730
756
730
858
730
149 TONN ES
418
730
H
J
Throat
Openin g Hoo k
T hickWith
Flapp er ness
(m m)
(mm)
114
232
114
232
114
232
114
232
114
232
114
232
Dead End ‡
K
Hoo k
Width
(mm)
152
152
152
152
152
152
Std.
Wire
Line
Sizes
(m m)*
19-28
19-28
19-28
22-32
22-32
22-32
T
T hickness
(m m)
44.5
44.5
44.5
44.5
44.5
44.5
U
Pin
Hole
(mm )
64.5
64.5
64.5
64.5
64.5
64.5
Weight
Each
(kg.)
1292
1427
1586
1508
1795
2013
114
114
114
114
114
114
114
114
114
114
114
114
114
114
114
232
232
232
232
232
232
232
232
232
232
232
232
232
232
232
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
22-32
22-32
22-32
22-32
22-32
22-32
16-25
16-25
16-25
19-28
19-28
19-28
22-32
22-32
22-32
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
1249
1535
1753
1506
1792
2009
1200
1309
1376
1292
1427
1586
1508
1795
2013
114
114
114
114
114
114
114
114
114
114
114
114
114
114
114
232
232
232
232
232
232
232
232
232
232
232
232
232
232
232
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
22-32
22-32
22-32
22-32
22-32
22-32
16-25
16-25
16-25
19-28
19-28
19-28
22-32
22-32
22-32
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
1249
1535
1753
1506
1792
2009
1200
1309
1376
1292
1427
1586
1508
1795
2013
114
114
114
114
114
114
114
114
114
114
114
114
114
114
114
232
232
232
232
232
232
232
232
232
232
232
232
232
232
232
152
152
152
152
152
152
152
152
152
152
152
152
152
152
152
22-32
22-32
22-32
22-32
22-32
22-32
16-25
16-25
16-25
19-28
19-28
19-28
22-32
22-32
22-32
—
—
—
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
—
—
—
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
1249
1535
1753
1506
1792
2009
1200
1309
1376
1292
1427
1586
1508
1795
2013
114
114
114
114
114
114
114
114
114
114
114
114
232
232
232
232
232
232
232
232
232
232
232
232
152
152
152
152
152
152
152
152
152
152
152
152
22-32
22-32
22-32
22-32
22-32
22-32
19-28
19-28
19-28
22-32
22-32
22-32
—
—
—
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
—
—
—
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
1249
1535
1753
1658
1945
2164
1292
1427
1586
1508
1795
2013
114
232
152
22-32
—
—
1249
247
McKissick®
Blocks
Mo del
No.
M115SX20L
M115SX20M
M115SX20H
M115SX24L
M115SX24M
M115SX24H
Inquiry
Stock
No.
2013111
2013115
2013119
2013123
2013127
2013131
Working
Load
Limit
(t) †
104
104
104
104
104
104
Mo del
No.
M165Q24M
M165Q24H
M165QN24L
M165QN24M
M165QN24H
M165SX20L
M165SX20M
M165SX20H
M165SX24L
M165SX24M
M165SX24H
Inquiry
Stock
No.
2013351
2013355
2013359
2013363
2013367
2013371
2013375
2013379
2013383
2013387
2013391
Working
Load
Limit
(t) †
149
149
149
149
149
149
149
149
149
149
149
M200QN24L
M200QN24M
M200QN24H
M200QN30L
M200QN30M
M200QN30H
M200SX24L
M200SX24M
M200SX24H
M200SX30L
M200SX30M
M200SX30H
2013395
2013399
2013403
2013396
2013400
2013404
2013407
2013411
2013415
2013419
2013423
2013427
M225QN24L
M225QN24M
M225QN24H
M225QN30L
M225QN30M
M225QN30H
M225SX24L
M225SX24M
M225SX24H
M225SX30L
M225SX30M
M225SX30H
A
Overall
Len gth
(mm)
1829
1829
1962
1962
1962
1861
1861
1861
1962
1962
1962
B
Net
Leng th
(mm )
1597
1597
1597
1597
1597
1496
1496
1496
1597
1597
1597
180
180
180
180
180
180
180
180
180
180
180
180
2102
2102
2102
2254
2254
2254
2102
2102
2102
2254
2254
2254
1721
1721
1721
1873
1873
1873
1721
1721
1721
1873
1873
1873
2013420
2013424
2013428
2013421
2013425
2013429
2013422
2013426
2013430
2013432
2013436
2013440
204
204
204
204
204
204
204
204
204
204
204
204
2102
2102
2102
2254
2254
2254
2102
2102
2102
2254
2254
2254
1721
1721
1721
1873
1873
1873
1721
1721
1721
1873
1873
1873
M250SX30L
M250SX30M
M250SX30H
M250SV24L
M250SV24M
M250SV24H
2013431
2013435
2013439
2013443
2013447
2013451
226
226
226
226
226
226
2369
2369
2369
2216
2216
2216
1965
1965
1965
1813
1813
1813
M275SX30L
M275SX30M
M275SX30H
M275SV24L
M275SV24M
M275SV24H
2013456
2013460
2013464
2013457
2013461
2013465
249
249
249
249
249
249
2369
2369
2369
2216
2216
2216
1965
1965
1965
1813
1813
1813
M300SX30L
M300SX30M
M300SX30H
M300SV24L
M300SV24M
M300SV24H
M300OCT30L
M300OCT30M
M300OCT30H
2013479
2013483
2013487
2013491
2013495
2013499
2013527
2013531
2013535
272
272
272
272
272
272
272
272
272
2369
2369
2369
2216
2216
2216
2369
2369
2369
1965
1965
1965
1813
1813
1813
1965
1965
1965
lk
380B
H
J
Throat
E
Openin g Hoo k
F
Th ickT hickWith
n ess
(mm )
(mm)
(mm)
(mm)
614
730
114
232
716
730
114
232
559
730
114
232
756
730
114
232
857
730
114
232
559
629
114
232
673
629
114
232
775
883
114
232
560
730
114
232
756
730
114
232
858
730
114
232
180 TON NES
610
730
127
248
806
730
127
248
908
730
127
248
610
883
127
248
673
883
127
248
711
883
127
248
610
730
127
248
806
730
127
248
908
730
127
248
610
883
127
248
673
883
127
248
711
883
127
248
204 TON NES
610
730
159
270
806
730
159
270
908
730
159
270
610
883
159
270
673
883
159
270
711
883
159
270
610
730
159
270
806
730
159
270
908
730
159
270
610
883
159
270
673
883
159
270
711
883
159
270
226 TON NES
724
927
159
270
826
927
159
270
876
927
159
270
914
730
159
270
1111
730
159
270
1213
730
159
270
249 TON NES
724
927
159
270
826
927
159
270
876
927
159
270
914
730
159
270
1111
730
159
270
1213
730
159
270
272 TON NES
724
927
159
270
826
927
159
270
876
927
159
270
914
730
159
270
1111
730
159
270
1213
730
159
270
914
927
159
270
965
927
159
270
991
927
159
270
Dead End ‡
K
Hoo k
Width
(mm)
152
152
152
152
152
152
152
152
152
152
152
Std.
Wire
Line
Sizes
(mm)*
22-32
22-32
22-32
22-32
22-32
19-28
19-28
19-28
22-32
22-32
22-32
T
T hickness
(m m)
—
—
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
U
Pin
Hole
(mm )
—
—
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
178
178
178
178
178
178
178
178
178
178
178
178
22-32
22-32
22-32
25-35
25-35
25-35
22-32
22-32
22-32
25-35
25-35
25-35
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
2087
2439
2649
2378
2786
3049
1985
2275
2491
2540
3207
3272
184
184
184
184
184
184
184
184
184
184
184
184
22-32
22-32
22-32
25-35
25-35
25-35
22-32
22-32
22-32
25-35
25-35
25-35
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
2119
2439
2649
2378
2786
3049
1985
2272
2491
2601
3009
3272
184
184
184
184
184
184
25-35
25-35
25-35
22-32
22-32
22-32
57.0
57.0
57.0
57.0
57.0
57.0
64.5
64.5
64.5
64.5
64.5
64.5
3299
3699
3957
2930
3249
3460
184
184
184
184
184
184
25-35
25-35
25-35
22-32
22-32
22-32
57.0
57.0
57.0
57.0
57.0
57.0
64.5
64.5
64.5
64.5
64.5
64.5
3299
3699
3957
2930
3249
3460
184
184
184
184
184
184
184
184
184
25-35
25-35
25-35
22-32
22-32
22-32
25-35
25-35
25-35
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
64.5
3299
3699
3957
2930
3249
3460
4602
4938
5258
Weight
Each
(kg.)
1535
1753
1658
1945
2164
1292
1427
1586
1508
1795
2013
*Additional wire line sizes available upon request.
† Ultimate Load is 4 times the Working Load Limit unless otherwise noted.
‡ D ead End dimensions for 2, 3, & 4 sheave blocks are shown on page 234.
@ - Ultimate Load is 3.6 times the Working Load Limit
248
All Rights Reserved
s k c o l B
e n a r C
s
e i r e S
0 8 3
®
k c i s
s i Kc M
Replacement Sheaves for McKissick® 380 Series Crane Blocks
• Sheave diameters range - 10" thru 24" (254mm thru 610mm).
• 16" (406mm) diameter sheaves and larger are Roll Forged™ with Flame hardened grooves
to minimum Rockwell 35C.
• Standard replacement sheaves are furnished with roller bearings. Bronze bushed sheaves are
• Wire line size range - 7/16" thru 1-1/4" (11mm thru 32mm).
hv
380S
Model
No .
SHV 10
SHV 12
SHV 14
SHV 16
SHV 16
SHV 16
SHV 18
SHV 18
SHV 20
SHV 20
SHV 20
SHV 24
SHV 24
SHV 24
SHV 24
Weig ht
Each
(kg )
11.8
12.2
15.4
19.1
19.5
19.5
28.1
28.1
39.5
39.5
44.5
53
53
56
62
McKissick®
Blocks
In quiry
Stock No.
4700008
4700017
4700026
4700035
4700044
4700053
4700062
4700071
4700081
4700089
4700098
4700107
4700116
4700125
4700134
Replacement Sheaves for McKissick® 380 Series Cran e Blocks
No minal
Sh aft
Hub
Sheave
Standard Wire
Diam eter
Wid th
Diameter
L ine Sizes
(mm )
(m m)
(mm)
(m m)
B
C
A
254
63.5
51.0
11-16
305
63.5
51.0
13-19
356
63.5
51.0
13-19
406
63.5
51.0
14-22
406
76.0
51.0
14-22
406
76.0
63.5
14-22
457
76.0
63.5
16-25
457
89.0
63.5
16-25
508
76.0
63.5
19-28
508
89.0
63.5
19-28
508
114
70.0
19-28
610
76.0
63.5
22-32
610
89.0
63.5
22-32
610
114
70.0
22-32
610
127
70.0
22-32
All Rights Reserved
249
McKissick® Easy Reeve® Crane Blocks
380 Series Easy Reeve® Hook Blocks
SEE APPLICATION AND
WARNING INFORMATION
On Pages 290 - 297
• Wide range of product available.
• Capacity: 4,5 to 72 tonnes - Larger Models Available.
• Sheave Sizes: 254 mm - 508 mm.
• Wire Line Sizes: 11 - 28 mm
• Manufactured by an ISO 9001 and API Q1 certified
facility.
• All single point shank hooks are genuine Crosby®,
forged alloy steel, Quenched and Tempered, and have the
patented QUIC-CHECK® markings (Duplex hooks are
available on most sizes).
• All Easy Reeve® Blocks are furnished standard with
Roller Bearings.
• Reeving Guides Standard - All Models.
• Blocks thru 20 tons use 319N hooks with S-4320 latches.
• Heavy Duty Positive Locking (PL) Latch - Models: 25
tons and larger.
• Sheave lubrication through center pin -Separate lube channel to each bearing.
• Sheaves fully protected by side plates.
• Dual action hook (Swings and Rotates).
• Repair parts available through world wide distribution
network.
• Design Factor of 4 to 1 (unless otherwise noted).
• All Easy Reeve® EORFNV DQG ODUJHU DUH IXUQLVKHG
ZLWK 0F.LVVLFN® Roll-Forged™ sheaves with flame
hardened grooves.
• Look for the Orange Hook . . . the mark of genuine
McKissick® quality.
Center “Dead End” to
promote better block
travel under various reev-
OPTIONS AVAILABLE
• Duplex Hooks (68 tonnes & larger)
• Swivel Tee and Shackle Assemblies
• Sheave Shrouds
• Anti Rotation - Locking Device
(68 tonnes & larger)
• Plate Steel Cheek Weights
Sheave Guards that open to
allow block reeving without
removing the rope end fitting.
• Third party testing with Certification
available upon
request.
Flat Bottom side plate for self
standing during reeving process.
Forged Crosby® alloy steel hooks with patented QUIC-CHECK® markings
and Heavy Duty positive locking hook latch.
250
All Rights Reserved
McKissick® Easy Reeve® Crane Blocks
Dead End Chart
(Double, Triple & Quad Sheave Blocks*)
Dimensions
(mm)
Wire Rope
Size
(mm)
T
Recommended Wedge Socket
McKissick®
US-422 / US-422T
Utility Socket
Thickness
U
Hole
Diameter
Stock No.
11
25.4
32.5
1044309
US4
13
25.4
32.5
1044318
US4
13
14
25.4
32.5
1044336
US5
14
16
25.4
32.5
1044345
US5
16
19
31.8
42.2
1044363
US6
19
22
31.8
42.2
1038580
US7
22
25
31.8
42.2
1038607
US8
25
28
44.5
65.0
1038616
US10
28
32
44.5
65.0
1038625
US10
32
Size
(mm)
11
US-422T TERMINATORTM Style.
All Rights Reserved
251
0F.LVVLFN(DV\5HHYH &UDQH%ORFNV
• Specify Wire Line size when ordering.
• Dead End Dimensions on page 251 of this catalog.
A
Overall
L en gth
(mm)
B
Net
Leng th
(m m)
E
Block
Th ickn ess
(mm )
Model
No .
Inqu iry
Stock
No.
Wo rking
L oad
L imit
(t)*
E5S10L
E5S10M
E5S10H
2014001
2014003
2014004
4.5
4.5
4.5
909
909
909
789
789
789
174
225
263
E10S10L
E10S10M
E10S10H
E10S14L
E10S14M
E10S14H
E10S16L
E10S16M
E10S16H
E10D10L
E10D10M
E10D10H
E10D12L
E10D12M
E10D12H
E10T10L
E10T10M
E10T10H
E10T12L
E10T12M
E10T12H
E10Q14L
E10Q14M
E10Q14H
2014011
2014013
2014014
2014021
2014023
2014024
2014031
2014033
2014034
2014041
2014043
2014044
2014051
2014053
2014054
2014061
2014063
2014064
2014071
2014073
2014074
2014081
2014083
2014084
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
909
909
909
1001
1001
1001
1096
1096
1096
909
909
909
947
947
947
909
909
909
947
947
947
1001
1001
1001
789
789
789
881
881
881
976
976
976
789
789
789
827
827
827
789
789
789
827
827
827
881
881
881
174
225
263
174
225
263
174
225
263
174
225
263
174
225
263
207
258
296
207
258
296
264
314
353
E15S10L
E15S10M
E15S10H
E15S12L
E15S12M
E15S12H
E15S14L
E15S14M
E15S14H
E15S16L
E15S16M
E15S16H
E15D10L
E15D10M
E15D10H
E15D12L
E15D12M
E15D12H
E15T10L
E15T10M
E15T10H
E15T12L
E15T12M
E15T12H
E15Q14L
E15Q14M
E15Q14H
2014091
2014093
2014094
2014101
2014103
2014104
2014111
2014113
2014114
2014121
2014123
2014124
2014131
2014133
2014134
2014141
2014143
2014144
2014151
2014153
2014154
2014161
2014163
2014164
2014171
2014173
2014174
13.5
13.5
13.5
13.5
13.5
13.5
13.5
13.5
13.5
13.5
13.5
13.5
13.5
13.5
13.5
13.5
13.5
13.5
13.5
13.5
13.5
13.5
13.5
13.5
13.5
13.5
13.5
909
909
909
947
947
947
1001
1001
1001
1096
1096
1096
909
909
909
947
947
947
909
909
909
947
947
947
1001
1001
1001
789
789
789
827
827
827
881
881
881
976
976
976
789
789
789
827
827
827
789
789
789
827
827
827
881
881
881
174
225
263
174
225
263
174
225
263
174
225
263
174
225
263
174
225
263
207
258
296
207
258
296
264
314
353
E20S10L
E20S10M
E20S10H
E20S14L
E20S14M
E20S14H
2014181
2014183
2014184
2014191
2014193
2014194
18
18
18
18
18
18
957
957
957
1049
1049
1049
828
828
828
920
920
920
174
225
263
174
225
263
EZ
H
F
T hroat
Blo ck
Opening
Width
with Flapper
(mm)
(mm )
4.5 Tonnes
368
48.5
368
48.5
368
48.5
9 T onnes
368
48.5
368
48.5
368
48.5
464
48.5
464
48.5
464
48.5
521
48.5
521
48.5
521
48.5
368
48.5
368
48.5
368
48.5
419
48.5
419
48.5
419
48.5
368
48.5
368
48.5
368
48.5
419
48.5
419
48.5
419
48.5
464
48.5
464
48.5
464
48.5
13.5 Tonnes
368
48.5
368
48.5
368
48.5
419
48.5
419
48.5
419
48.5
464
48.5
464
48.5
464
48.5
521
48.5
521
48.5
521
48.5
368
48.5
368
48.5
368
48.5
419
48.5
419
48.5
419
48.5
368
48.5
368
48.5
368
48.5
419
48.5
419
48.5
419
48.5
464
48.5
464
48.5
464
48.5
18 T onnes
368
70.0
368
70.0
368
70.0
464
70.0
464
70.0
464
70.0
J
Hook
T hickn ess
(mm )
K
Hook
Wid th
(mm )
Stan dard
Wire R ope
Size
(m m)
Weig ht
Each
(kg.) †
Z
r5E
F
66.0
66.0
66.0
49.3
49.3
49.3
11-16
11-16
11-16
107
155
192
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
11-16
11-16
11-16
13-19
13-19
13-19
14-22
14-22
14-22
11-16
11-16
11-16
13-19
13-19
13-19
11-16
11-16
11-16
13-19
13-19
13-19
13-19
13-19
13-19
107
155
192
125
194
246
149
239
308
122
170
204
126
182
225
144
192
230
147
202
245
194
267
319
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
66.0
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
11-16
11-16
11-16
13-19
13-19
13-19
13-19
13-19
13-19
14-22
14-22
14-22
11-16
11-16
11-16
13-19
13-19
13-19
11-16
11-16
11-16
13-19
13-19
13-19
13-19
13-19
13-19
107
155
192
114
170
213
125
194
246
149
239
308
122
170
207
126
182
225
144
192
230
147
202
245
194
267
319
75.5
75.5
75.5
75.5
75.5
75.5
60.5
60.5
60.5
60.5
60.5
60.5
11-16
11-16
11-16
13-19
13-19
13-19
113
161
198
133
201
254
Z
r10E
F
Z
r15E
F
Z
r20E
F
252
All Rights Reserved
A
Overall
L en gth
(mm)
1195
1195
1195
995
995
995
1049
1049
1049
995
995
995
1049
1049
1049
995
995
995
1049
1049
1049
B
Net
Leng th
(m m)
1066
1066
1066
866
866
866
920
920
920
866
866
866
920
920
920
866
866
866
920
920
920
E
Block
Th ickn ess
(mm )
174
231
269
174
225
263
174
225
263
207
258
296
207
258
296
264
314
353
264
314
353
Model
No .
E20S18L
E20S18M
E20S18H
E20D12L
E20D12M
E20D12H
E20D14L
E20D14M
E20D14H
E20T12L
E20T12M
E20T 12H
E20T14L
E20T14M
E20T 14H
E20Q12L
E20Q12M
E20Q12H
E20Q14L
E20Q14M
E20Q14H
Inqu iry
Stock
No.
2014201
2014203
2014204
2014211
2014213
2014214
2014221
2014223
2014224
2014231
2014233
2014234
2014241
2014243
2014244
2014251
2014253
2014254
2014261
2014263
2014264
Wo rking
L oad
L imit
(t)*
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
18
E25S16L
E25S16M
E25S16H
E25S18L
E25S18M
E25S18H
E25D12L
E25D12M
E25D12H
E25D14L
E25D14M
E25D14H
E25T12L
E25T12M
E25T 12H
E25T14L
E25T14M
E25T 14H
E25Q12L
E25Q12M
E25Q12H
E25Q14L
E25Q14M
E25Q14H
2014271
2014273
2014274
2014281
2014283
2014284
2014291
2014293
2014294
2014301
2014303
2014304
2014311
2014313
2014314
2014321
2014323
2014324
2014331
2014333
2014334
2014341
2014343
2014344
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
1145
1145
1145
1195
1195
1195
995
995
995
1049
1049
1049
995
995
995
1049
1049
1049
995
995
995
1049
1049
1049
1015
1015
1015
1066
1066
1066
866
866
866
920
920
920
866
866
866
920
920
920
866
866
866
920
920
920
174
225
263
174
231
269
174
225
263
174
225
263
207
258
296
207
258
296
264
314
353
264
314
353
E30S18L
E30S18M
E30S18H
E30S20L
E30S20M
E20S20H
E30D14L
E30D14M
E30D14H
E30D18L
E30D18M
E30D18H
E30T14L
E30T14M
E30T 14H
E30T16L
E30T16M
E30T 16H
E30Q14L
E30Q14M
E30Q14H
2014351
2014353
2014354
2014356
2014358
2014359
2014361
2014363
2014364
2014371
2014373
2014374
2014381
2014383
2014384
2014391
2014393
2014394
2014401
2014403
2014404
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
1310
1310
1310
1399
1399
1399
1113
1113
1113
1310
1310
1310
1164
1164
1164
1259
1259
1259
1164
1164
1164
1173
1173
1173
1173
1173
1173
976
976
976
1173
1173
1173
1027
1027
1027
1122
1122
1122
1027
1027
1027
174
231
269
174
225
263
174
225
263
174
231
269
207
258
296
207
258
296
264
314
353
E35S20L
2014406
32
1502
1341
174
EZ
H
F
T hroat
Blo ck
Opening
Width
with Flapper
(mm)
(mm)
565
70.0
565
70.0
565
70.0
419
70.0
419
70.0
419
70.0
464
70.0
464
70.0
464
70.0
419
70.0
419
70.0
419
70.0
464
70.0
464
70.0
464
70.0
419
70.0
419
70.0
419
70.0
464
70.0
464
70.0
464
70.0
23 Tonnes
521
70.0
521
70.0
521
70.0
565
70.0
565
70.0
565
70.0
419
70.0
419
70.0
419
70.0
464
70.0
464
70.0
464
70.0
419
70.0
419
70.0
419
70.0
464
70.0
464
70.0
464
70.0
419
70.0
419
70.0
419
70.0
464
70.0
464
70.0
464
70.0
27 Tonnes
565
82.5
565
82.5
565
82.5
622
82.5
622
82.5
622
82.5
464
82.5
464
82.5
464
82.5
565
82.5
565
82.5
565
82.5
464
82.5
464
82.5
464
82.5
521
82.5
521
82.5
521
82.5
464
82.5
464
82.5
464
82.5
32 Tonnes
622
76.0
J
Hook
Th ickn ess
(mm)
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
K
Hook
Width
(mm )
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
Stan dard
Wire Ro pe
Size
(m m)
16-26
16-26
16-26
13-19
13-19
13-19
13-19
13-19
13-19
13-19
13-19
13-19
13-19
13-19
13-19
13-19
13-19
13-19
13-19
13-19
13-19
Weig ht
Each
(kg.) †
177
297
378
132
188
231
148
216
269
151
208
251
171
239
292
182
238
280
204
273
324
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
75.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
60.5
14-22
14-22
14-22
16-26
16-26
16-26
13-19
13-19
13-19
13-19
13-19
13-19
13-19
13-19
13-19
13-19
13-19
13-19
13-19
13-19
13-19
13-19
13-19
13-19
155
244
313
177
296
378
132
188
231
148
216
269
151
208
251
167
239
292
182
238
280
204
273
324
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
16-26
16-26
16-26
19-28
19-28
19-28
13-19
13-19
13-19
16-26
16-26
16-26
13-19
13-19
13-19
14-22
14-22
14-22
13-19
13-19
13-19
207
326
407
253
393
500
171
239
292
234
353
435
198
266
319
229
319
387
228
297
349
116
92.0
19-28
253
Z
r30E
F
Z
r35E
F
All Rights Reserved
253
McKissick®
Blocks
Z
r25E
F
A
Overall
L en gth
(mm)
1502
1502
1413
1413
1413
1267
1267
1267
1362
1362
1362
1267
1267
1267
B
Net
Leng th
(m m)
1341
1341
1252
1252
1252
1106
1106
1106
1202
1202
1202
1106
1106
1106
E
Block
Th ickn ess
(mm )
225
263
174
231
269
207
258
296
207
258
296
264
314
353
Model
No .
E35S20M
E35S20H
E35D18L
E35D18M
E35D18H
E35T14L
E35T14M
E35T14H
E35T16L
E35T16M
E35T16H
E35Q14L
E35Q14M
E35Q14H
Inqu iry
Stock
No.
2014408
2014409
2014411
2014413
2014414
2014421
2014423
2014424
2014431
2014433
2014434
2014441
2014443
2014444
Wo rking
L oad
L imit
(t)*
32
32
32
32
32
32
32
32
32
32
32
32
32
32
E40T14L
E40T14M
E40T14H
E40T16L
E40T16M
E40T16H
E40T18L
E40T18M
E40T18H
E40Q14L
E40Q14M
E40Q14H
E40Q16L
E40Q16M
E40Q16H
2014451
2014453
2014454
2014461
2014463
2014464
2014471
2014473
2014474
2014481
2014483
2014484
2014491
2014493
2014494
36
36
36
36
36
36
36
36
36
36
36
36
36
36
36
1319
1319
1319
1415
1415
1415
1465
1465
1465
1319
1319
1319
1415
1415
1415
1146
1146
1146
1242
1242
1242
1292
1292
1292
1146
1146
1146
1242
1242
1242
207
258
296
207
258
296
207
264
302
264
314
353
264
314
353
E45T14L
E45T14M
E45T14H
E45T16L
E45T16M
E45T16H
E45T18L
E45T18M
E45T18H
E45Q14L
E45Q14M
E45Q14H
E45Q16L
E45Q16M
E45Q16H
2014501
2014503
2014504
2014511
2014513
2014514
2014521
2014523
2014524
2014531
2014533
2014534
2014541
2014543
2014544
41
41
41
41
41
41
41
41
41
41
41
41
41
41
41
1319
1319
1319
1415
1415
1415
1465
1465
1465
1319
1319
1319
1415
1415
1415
1146
1146
1146
1242
1242
1242
1292
1292
1292
1146
1146
1146
1242
1242
1242
207
258
296
207
258
296
207
264
302
264
314
353
264
314
353
E50T18L
E50T18M
E50T18H
E50Q16L
E50Q16M
E50Q16H
E50QN 16L
E50QN 16M
E50QN16H
2014551
2014553
2014554
2014561
2014563
2014564
2014571
2014573
2014574
45
45
45
45
45
45
45
45
45
1619
1619
1619
1568
1568
1568
1568
1568
1568
1403
1403
1403
1353
1353
1353
1353
1353
1353
283
340
378
338
389
427
357
408
446
E55T18L
E55T18M
E55T18H
E55Q16L
E55Q16M
E55Q16H
E55QN 16L
E55QN 16M
E55QN16H
2014581
2014583
2014584
2014591
2014593
2014594
2014601
2014603
2014604
50
50
50
50
50
50
50
50
50
1619
1619
1619
1568
1568
1568
1568
1568
1568
1403
1403
1403
1353
1353
1353
1353
1353
1353
283
340
378
338
389
427
357
408
446
E60T20L
E60T20M
E60T20H
2014611
2014613
2014614
54
54
54
1708
1708
1708
1492
1492
1492
283
334
372
EZ
H
F
T hroat
Blo ck
Opening
Width
with Flapper
(mm)
(mm )
622
76.0
622
76.0
565
76.0
565
76.0
565
76.0
464
76.0
464
76.0
464
76.0
521
76.0
521
76.0
521
76.0
464
76.0
464
76.0
464
76.0
36 Tonnes
464
86.0
464
86.0
464
86.0
521
86.0
521
86.0
521
86.0
565
86.0
565
86.0
565
86.0
464
86.0
464
86.0
464
86.0
521
86.0
521
86.0
521
86.0
41 T onnes
464
86.0
464
86.0
464
86.0
521
86.0
521
86.0
521
86.0
565
86.0
565
86.0
565
86.0
464
86.0
464
86.0
464
86.0
521
86.0
521
86.0
521
86.0
45 T onnes
565
105
565
105
565
105
521
105
521
105
521
105
521
105
521
105
521
105
50 T onnes
565
105
565
105
565
105
521
105
521
105
521
105
521
105
521
105
521
105
54 Tonnes
622
105
622
105
622
105
J
Hook
T hickn ess
(mm )
116
116
116
116
116
116
116
116
116
116
116
116
116
116
K
Hook
Wid th
(mm )
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
92.0
Stan dard
Wire R ope
Size
(m m)
19-28
19-28
16-26
16-26
16-26
13-19
13-19
13-19
14-22
14-22
14-22
13-19
13-19
13-19
Weig ht
Each
(kg.) †
393
500
258
377
458
221
290
342
253
342
411
252
320
372
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
13-19
13-19
13-19
14-22
14-22
14-22
16-26
16-26
16-26
13-19
13-19
13-19
14-22
14-22
14-22
247
315
368
279
372
437
322
441
497
277
346
398
313
403
472
129
129
129
129
129
129
129
129
129
129
129
129
129
129
129
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
94.5
13-19
13-19
13-19
14-22
14-22
14-22
16-26
16-26
16-26
13-19
13-19
13-19
14-22
14-22
14-22
247
315
368
279
372
437
322
441
522
277
346
398
313
403
472
152
152
152
152
152
152
152
152
152
113
113
113
113
113
113
113
113
113
16-26
16-26
16-26
14-22
14-22
14-22
14-22
14-22
14-22
474
593
674
484
551
642
520
610
678
152
152
152
152
152
152
152
152
152
113
113
113
113
113
113
113
113
113
16-26
16-26
16-26
14-22
14-22
14-22
14-22
14-22
14-22
474
593
674
484
574
642
520
610
678
152
152
152
113
113
113
19-28
19-28
19-28
531
668
758
Z
r45E
F
Z
r50E
F
Z
r5E
F
254
All Rights Reserved
A
Overall
L en gth
(mm)
1619
1619
1619
1619
1619
1619
1708
1708
1708
B
Net
Leng th
(m m)
1403
1403
1403
1403
1403
1403
1492
1492
1492
E
Block
Th ickn ess
(mm )
338
395
433
357
414
452
357
408
446
Model
No .
E60Q18L
E60Q18M
E60Q18H
E60QN18L
E60QN18M
E60QN18H
E60QN20L
E60QN20M
E60QN20H
Inqu iry
Stock
No.
2014621
2014623
2014624
2014631
2014633
2014634
2014641
2014643
2014644
Wo rking
L oad
L imit
(t)*
54
54
54
54
54
54
54
54
54
E65T20L
E65T20M
E65T 20H
E65Q18L
E65Q18M
E65Q18H
E65QN18L
E65QN18M
E65QN18H
E65QN20L
E65QN20M
E65QN20H
2014651
2014653
2014654
2014661
2014663
2014664
2014671
2014673
2014674
2014681
2014683
2014684
59
59
59
59
59
59
59
59
59
59
59
59
1708
1708
1708
1619
1619
1619
1619
1619
1619
1708
1708
1708
1492
1492
1492
1403
1403
1403
1403
1403
1403
1492
1492
1492
283
334
372
338
395
433
357
414
452
357
408
446
E70T20L
E70T20M
E70T 20H
E70Q18L
E70Q18M
E70Q18H
E70QN18L
E70QN18M
E70QN18H
E70QN20L
E70QN20M
E70QN20H
2014691
2014693
2014694
2014701
2014703
2014704
2014711
2014713
2014714
2014721
2014723
2014724
63
63
63
63
63
63
63
63
63
63
63
63
1884
1884
1884
1796
1796
1796
1796
1796
1796
1884
1884
1884
1651
1651
1651
1562
1562
1562
1562
1562
1562
1651
1651
1651
283
334
372
338
395
433
357
414
452
357
408
446
E75T20L
E75T20M
E75T 20H
E75Q18L
E75Q18M
E75Q18H
E75QN18L
E75QN18M
E75QN18H
E75QN20L
E75QN20M
E75QN20H
2014731
2014733
2014734
2014741
2014743
2014744
2014751
2014753
2014754
2014761
2014763
2014764
68
68
68
68
68
68
68
68
68
68
68
68
1884
1884
1884
1796
1796
1796
1796
1796
1796
1884
1884
1884
1651
1651
1651
1562
1562
1562
1562
1562
1562
1651
1651
1651
283
334
372
338
395
433
357
414
452
357
408
446
E80T20L
E80T20M
E80T 20H
E80Q18L
E80Q18M
E80Q18H
E80QN18L
E80QN18M
E80QN18H
E80QN20L
E80QN20M
E80QN20H
2014771
2014773
2014774
2014781
2014783
2014784
2014791
2014793
2014794
2014801
2014803
2014804
72
72
72
72
72
72
72
72
72
72
72
72
1884
1884
1884
1796
1796
1796
1796
1796
1796
1884
1884
1884
1651
1651
1651
1562
1562
1562
1562
1562
1562
1651
1651
1651
283
334
372
338
395
433
357
414
452
357
408
446
EZ
H
F
T hroat
Blo ck
Opening
Width
with Flapper
(mm)
(mm)
565
105
565
105
565
105
565
105
565
105
565
105
622
105
622
105
622
105
59 Tonnes
622
105
622
105
622
105
565
105
565
105
565
105
565
105
565
105
565
105
622
105
622
105
622
105
63 Tonnes
622
137
622
137
622
137
565
137
565
137
565
137
565
137
565
137
565
137
622
137
622
137
622
137
68 Tonnes
622
137
622
137
622
137
565
137
565
137
565
137
565
137
565
137
565
137
622
137
622
137
622
137
72 Tonnes
622
137
622
137
622
137
565
137
565
137
565
137
565
137
565
137
565
137
622
137
622
137
622
137
J
Hook
Th ickn ess
(mm)
152
152
152
152
152
152
152
152
152
K
Hook
Width
(mm )
113
113
113
113
113
113
113
113
113
Stan dard
Wire Ro pe
Size
(m m)
16-26
16-26
16-26
16-26
16-26
16-26
19-28
19-28
19-28
Weig ht
Each
(kg.) †
521
640
721
550
670
750
628
765
855
Z
r65E
F
152
152
152
152
152
152
152
152
152
152
152
152
113
113
113
113
113
113
113
113
113
113
113
113
19-28
19-28
19-28
16-26
16-26
16-26
16-26
16-26
16-26
19-28
19-28
19-28
531
668
758
521
640
721
550
670
750
628
765
855
170
170
170
170
170
170
170
170
170
170
170
170
122
122
122
122
122
122
122
122
122
122
122
122
19-28
19-28
19-28
16-26
16-26
16-26
16-26
16-26
16-26
19-28
19-28
19-28
626
762
853
658
777
858
629
748
830
754
891
982
170
170
170
170
170
170
170
170
170
170
170
170
122
122
122
122
122
122
122
122
122
122
122
122
19-28
19-28
19-28
16-26
16-26
16-26
16-26
16-26
16-26
19-28
19-28
19-28
626
762
853
658
777
858
629
748
830
754
891
982
170
170
170
170
170
170
170
170
170
170
170
170
122
122
122
122
122
122
122
122
122
122
122
122
19-28
19-28
19-28
16-26
16-26
16-26
16-26
16-26
16-26
19-28
19-28
19-28
626
762
853
658
777
858
629
748
830
754
891
982
Z
r70E
F
Z
r80E
F
* Ultimate Load is 4 times the Wor king Load Limit.
† Additional cheek weight kits are available.
All Rights Reserved
255
McKissick®
Blocks
Z
r75E
F
McKissick® Easy Reeve ® Crane Blocks
s k c
o l B
e n a
r C
®
e v e e R
y s a E
®
k c i s
s i Kc M
Replacement Sheaves for McKissick® Easy Reeve ® Crane Blocks
• 16" (406mm) diameter sheaves and larger are Roll Forged™ with Flame hardened grooves to
minimum Rockwell 35C.
• Sheave diameter range - 10" thru 20" (254 mm thru 508 mm).
• Standard replacement sheaves are furnished with roller bearings. Bronze bushed sheaves are
• Wire line size range - 7/16" thru 1-1/8" (11 thru 28 mm).
EZ
hv
S
Inq uiry
Stock
No.
4700205
4700214
4700223
4700232
4700241
4700250
4700269
4700278
4700287
4700296
4700304
256
Replacem ent Sheaves for McKissick ® EASY REEVE® Series Crane Blo cks
Nominal
Shaft
Hub
Stand ard Wire
Sheave
Diameter
Width
Line Size
D iam eter
(mm)
(mm)
(mm)
(mm )
B
C
254
76.0
44.5
11-16
305
76.0
44.5
13-19
305
89.0
51.0
13-19
356
76.0
44.5
13-19
356
89.0
51.0
13-19
406
76.0
44.5
14-22
406
89.0
51.0
14-22
457
76.0
44.5
16-25
457
89.0
51.0
16-25
457
114
57.0
16-25
508
114
57.0
19-28
Weight
Each
(kg.)
11.8
12.2
15.4
19.1
19.5
19.5
28.1
28.1
39.5
39.5
44.5
All Rights Reserved
McKissick® Scrap Handling Blocks
SEE APPLICATION AND
WARNING INFORMATION
On Pages 290-297
6<
• All single point shank hooks are genuine Crosby®, forged alloy steel,
Quenched and Tempered, and have the patented QUIC-CHECK® markings.
• Durable - Allows longer continuous duty cycle.
• Can be used with magnet and drop ball
• Single sheave design
• Dual action hook (Swings and Rotates)
• Utilize McKissick® Roll-Forged ™sheav es with flame hardened grooves.
• Furnished standard with Bronze Bushed Sheav es.
• Optional Tapered Roller Bearings.
s k
c o l B
g n i l d
n a H
p a r c S
®
k c i
s s i Kc M
381-SY
Scrap Handling Blocks
Dimensions
(mm )
381S
Y
Model
No .
S15S16L
S20S18L
S25S20L
S30S24L
S40S24L
381-SY Working
Sh eave
Inqu iry
Lo ad
Stock
Lim it Diameter
(mm)
No.
(t)*
2014810
13.5
406
2014812
18.0
457
2014814
22.5
508
2014816
27.0
610
2014818
36.0
610
Stand ard
Wire
Lin e
(mm )
14-22
16-25
19-28
22-32
22-32
Weight
Each
(kg.)
129
179
209
263
370
A
944
1004
1071
1281
1418
B
868
929
995
1189
1289
E
161
174
174
199
199
F
578
629
679
781
781
H
70.0
70.0
70.0
82.5
86.0
J
75.5
75.5
75.5
92.0
129
K
60.5
60.5
60.5
76.0
82.5
McKissick®
Blocks
* Ultimate Load is 4 times the Working Load Limit.
All Rights Reserved
257
McKissick® Tilt-Up Wall Blocks
SEE APPLICATION AND
WARNING INFORMATION
On Pages 290-297
786(5,(6
%/2&.6
• Wide Range of Sizes Available:
• 30 and 60 Ton Capacity (27 and 54 Tonnes)
• 1" to 2-1/4" (25mm to 60mm) Wire Line Size
• 16" to 24" (406mm to 610mm) Sheave Diameter
• Larger Capacity Blocks av ailable.
• Multiple Configurations Available:
• Swivel Hook
• Swivel Shackle
• Tailboard
• Upset Shackle
• Fixed Shackle
• McKissick ® Roll-Forged ™Sheaves:
• Flame Hardened Grooves
• 30 Ton (27 Tonnes) furnished with Roller Bearings
• 60 Ton (54 Tonnes) furnished with Tapered Roller Bearings with seals.
s k c
o l B
l l a W
p U- t l i T
®
k c i
s s i Kc M
High Capacity Snatch Blocks for Tilt-Up Wall Construction
258
With Swivel Hook
T U-480
TU-480
Weight
Sto ck
Each
No.
(kg)
2108300
102
2108312
102
2108324
102
2108336
102
2108348
102
With Swivel Sh ackle
TU-481
TU-481
Weight
Stock
Each
No.
(kg)
2108303
107
2108315
107
2108327
107
2108339
107
2108351
107
Working
Load L imit
(t)
27
27
27
27
27
Sheave
Dia.
(mm )
406
406
406
406
406
Wire
Lin e
Size
(mm)
25
28
32
35
38
27
27
27
27
27
508
508
508
508
508
25
28
32
35
38
2108360
2108372
2108384
2108396
2108408
109
109
109
109
109
2108363
2108375
2108387
2108399
2108411
113
113
113
113
113
54
54
54
54
54
457
457
457
457
457
25
28
32
35
38
2108420
2108435
2108450
2108465
2108480
177
177
177
177
177
2108423
2108438
2108453
2108468
2108483
177
177
177
177
177
54
54
54
54
54
54
54
54
54
54
610
610
610
610
610
610
610
610
610
610
25
28
32
35
38
41
44
48
51
57
2108495
2108510
2108525
2108540
2108555
2108570
2108585
2108600
2108615
2108630
204
204
204
204
204
204
204
204
204
204
2108498
2108513
2108528
2108543
2108558
2108573
2108588
2108603
2108618
2108633
204
204
204
204
204
204
204
204
204
204
All Rights Reserved
McKissick® Tilt-Up Wall Blocks
s k c o
l B
l l a W
p
U- t l i T
®
k c i
s s i Kc M
786(5,(6
%/2&.6
High Capacity Snatch Blocks for Tilt-Up Wall Construction
Tailb oard Style
T U-482
Weight
TU-482
Stock
Each
(kg)
No.
2108306
63.5
2108318
63.5
2108330
63.5
2108342
63.5
2108354
63.5
With Up set Sh ackle
TU-483
Weig ht
TU-483
Sto ck
Each
(kg )
No.
2108309
81.6
2108321
81.6
2108333
81.6
2108345
81.6
2108357
81.6
With Fixed Shackle
TU -484
Weight
TU-484
Stock
Each
(kg)
No.
2108645
72.6
2108648
72.6
2108651
72.6
2108654
72.6
2108657
72.6
Sheave
Diameter
(mm )
406
406
406
406
406
Wire Line
Size
(mm)
25
28
32
35
38
27
27
27
27
27
508
508
508
508
508
25
28
32
35
38
2108366
2108378
2108390
2108402
2108414
70.3
70.3
70.3
70.3
70.3
2108369
2108381
2108393
2108405
2108417
88.5
88.5
88.5
88.5
88.5
2108660
2108663
2108666
2108669
2108672
79.4
79.4
79.4
79.4
79.4
54
54
54
54
54
457
457
457
457
457
25
28
32
35
38
2108426
2108441
2108456
2108471
2108486
104
104
104
104
104
2108429
2108444
2108459
2108474
2108489
154
154
154
154
154
2108432
2108447
2108462
2108477
2108492
132
132
132
132
132
54
54
54
54
54
54
54
54
54
54
610
610
610
610
610
610
610
610
610
610
25
28
32
35
38
41
44
48
51
57
2108501
2108516
2108531
2108546
2108561
2108576
2108591
2108606
2108621
2108636
132
132
132
132
132
132
132
132
132
132
2108504
2108519
2108534
2108549
2108564
2108579
2108594
2108609
2108624
2108639
181
181
181
181
181
181
181
181
181
181
2108507
2108522
2108537
2108552
2108567
2108582
2108597
2108612
2108627
2108642
159
159
159
159
159
159
159
159
159
159
McKissick®
Blocks
Working
Load L imit
(t)
27
27
27
27
27
All Rights Reserved
259
McKissick® Construction Blocks
680 Construction Blocks
• Wide Range of product available:
• Manufactured by an ISO 9001 and API Q1
• Capacity: 4,5 to 90 tonnes - Larger models
Certified facility.
• All 680 Series Blocks are furnished
Standard with Bronze Bushings.
• All 680 blocks 406 mm and larger, are furnished with McKissick® Roll Forged® sheaves
with flame hardened grooves.
• Sheaves are lubricated through center
pin, with a separate lube channel to each
sheave.
•
•
•
•
available.
Sheave sizes: 152 mm to 610 mm O.D.
Wire Line Sizes: 10 mm to 32 mm
Equipped with genuine Crosby® forged
steel, Quenched and Tempered shackles
that contain the patented QUIC-CHECK®
markings.
Design Factor of 4 to 1.
Options Available:
•
•
•
•
Roller bearing sheaves
Hanger & Bolt Only models available
Third party testing with certification
Galvanized finish - Most models
With Hanger
With Shackle
SEE APPLICATION AND
WARNING INFORMATION
Bolt Only
On Page 290 - 297
260
All Rights Reserved
“H” Fitting - Blocks with Hangers Only
McKissick
Blocks
“P” Fitting - Block with Bolt Only
NOTE: The outside of attaching plates must be within the
indicated load areas. Means must be provided to keep
attaching plates equally spaced from the block side plates.
All Rights Reserved
“S” Fitting - Blocks With Hangers and Shackles
261
s k
c o l B
n o i t c u r t s n o C
®
k c i s s i Kc M
%/2&.6
3),77,1*
"P" Fitting - Blocks with Bolt Only - See Drawing on Page 261
Mo del
No.
680-P
Inqu iry
Sto ck No .
Wo rking
L oad
L imit
(t)
No. of
Sheaves
Sheave
Diam .
(mm)
B lo cks with Bo lt On ly Dimen sio ns
(mm)
A
B
C
D
4.5 Tonnes
41.1 45.2
41.1 45.2
41.1 97.0 26.9
41.1 97.0 26.9
41.1
148
26.9
41.1
148
26.9
6.8 Tonnes
41.1 45.2
41.1 45.2
41.1 97.0 15.7
41.1 97.0 15.7
41.1
148
15.7
41.1
148
15.7
9 Tonnes
54.0 45.2
54.0 45.2
54.0 45.2
54.0 45.2
54.0 97.0 22.4
54.0 97.0 22.4
54.0 97.0 22.4
54.0 97.0 22.4
54.0 97.0 22.4
54.0
148
22.4
54.0
148
22.4
54.0
148
22.4
54.0
148
22.4
54.0
200
22.4
54.0
200
22.4
13.6 Tonnes
73.0 52.0
73.0 52.0
73.0 52.0
73.0
110
31.8
73.0
110
31.8
73.0
110
31.8
73.0
169
31.8
73.0
169
31.8
73.0
169
31.8
73.0
169
31.8
73.0
227
31.8
18 Tonnes
76.0 64.5 19.1
76.0
110
19.1
76.0
110
19.1
76.0
110
19.1
76.0
169
19.1
E
F
G
H
I
J
K
X
Weig ht
Each
(kg .)
58.0
58.0
109
109
161
161
155
206
155
206
155
206
16.0
16.0
16.0
16.0
17.5
17.5
17.5
17.5
21.3
21.3
21.3
21.3
51.0
51.0
45.5
45.5
45.5
45.5
31.8
31.8
31.8
31.8
31.8
31.8
51.5
51.5
51.5
51.5
8.6
14.1
15.0
24.5
20.4
34.0
58.0
58.0
109
109
161
161
155
206
155
206
155
206
16.0
16.0
16.0
16.0
17.5
17.5
17.5
17.5
21.3
21.3
21.3
21.3
51.0
51.0
45.5
45.5
45.5
45.5
31.8
31.8
31.8
31.8
31.8
31.8
51.5
51.5
51.5
51.5
8.6
14.1
15.0
24.5
20.4
34.0
58.0
58.0
58.0
58.0
109
109
109
109
109
161
161
161
161
213
212.6
206
257
308
359
155
206
257
308
359
206
257
308
359
206
257
16.0
16.0
16.0
16.0
16.0
16.0
16.0
16.0
16.0
16.0
16.0
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
21.3
21.3
21.3
21.3
21.3
21.3
21.3
21.3
21.3
21.3
21.3
60.5
60.5
60.5
60.5
54.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
51.5
51.5
51.5
51.5
51.5
51.5
51.5
51.5
51.5
51.5
51.5
15.4
21.3
25.9
29.0
18.6
26.3
37
45
52
36.7
52
53
74
47
68
77.0
77.0
77.0
136
136
136
194
194
194
194
252
257
308
359
257
308
359
206
257
308
359
257
19.1
19.1
19.1
19.1
19.1
19.1
19.1
19.1
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
79.0
79.0
79.0
71.5
71.5
71.5
71.5
71.5
71.5
71.5
71.5
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
58.5
58.5
58.5
58.5
58.5
58.5
58.5
58.5
34.5
41.7
50
52
63
76
47.6
69
826
97
95
103
148
148
148
207
460
308
359
409
257
22.4
22.4
22.4
22.4
24.6
24.6
24.6
24.6
29.0
29.0
29.0
29.0
79.0
71.5
71.5
71.5
71.5
51.0
51.0
51.0
51.0
51.0
58.5
58.5
58.5
58.5
92
75
90
108
81
r5P
F
C5S6BP
C5S8BP
C5D6BP
C5D8BP
C5T 6BP
C5T 8BP
2101000
2101002
2101010
2101012
2101020
2101022
4.5
4.5
4.5
4.5
4.5
4.5
1
1
2
2
3
3
152
203
152
203
152
203
308
356
375
422
375
422
C7S6BP
C7S8BP
C7D6BP
C7D8BP
C7T 6BP
C7T 8BP
2101050
2101052
2101060
2101062
2101070
2101072
6.8
6.8
6.8
6.8
6.8
6.8
1
1
2
2
3
3
152
203
152
203
152
203
308
356
375
422
375
422
C10S8BP
C10S10BP
C10S12BP
C10S14BP
C10D6BP
C10D8BP
C10D10BP
C10D12BP
C10D14BP
C10T 8BP
C 10T 10BP
C 10T 12BP
C 10T 14BP
C10Q8BP
C10Q10B
2101100
2101102
2101104
2101106
2101110
2101112
2101114
2101116
2101118
2101120
2101122
2101124
2101126
2101130
2101132
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
1
1
1
1
2
2
2
2
2
3
3
3
3
4
4
203
254
305
356
152
203
254
305
356
203
254
305
356
203
254
384
435
483
536
399
443
494
541
595
443
494
541
595
443
494
C15S10B
C15S12BP
C15S14SP
C15D10BP
C15D12BP
C15D14BP
C15T 8BP
C 15T 10BP
C 15T 12BP
C 15T 14BP
C15Q10BP
2101170
2101172
2101174
2101180
2101182
2101184
2101190
2101192
2101194
2101196
2101200
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
1
1
1
2
2
2
3
3
3
3
4
254
305
356
254
305
356
203
254
305
356
254
487
535
586
564
611
662
513
564
611
662
564
C20S18BP
C20D12BP
C20D14BP
C20D16BP
C 20T 10BP
2101244
2101250
2101252
2101254
2101260
18.1
18.1
18.1
18.1
18.1
1
2
2
2
3
457
305
356
406
254
708
703
724
781
629
r7.5P
F
r10P
F
r15P
F
r20P
F
262
All Rights Reserved
Wo rking
L oad
L imit
(t)
18.1
18.1
18.1
18.1
18.1
18.1
18.1
C25S18BP
C25D12BP
C25D14BP
C25D16BP
C25T 10BP
C25T 12BP
C25T 14BP
C25T 16BP
C25Q08BP
C25Q10BP
C25Q12BP
C25Q14BP
2101314
2101320
2101322
2101324
2101330
2101332
2101334
2101336
2101340
2101342
2101344
2101346
C30D12BP
C30D14BP
C30D16BP
C30D18BP
C30T 10BP
C30T 12BP
C30T 14BP
C30T 16BP
C30Q10BP
C30Q12BP
C30Q14BP
C30Q16BP
Blo cks with Bo lt Only Dimen sio ns
(mm)
No. of
Sheaves
3
3
3
4
4
4
4
Sh eave
Diam .
(mm)
305
356
406
203
254
305
356
A
678
724
781
573
629
678
724
B
76.0
76.0
76.0
76.0
76.0
76.0
76.0
22.7
22.7
22.7
22.7
22.7
22.7
22.7
22.7
22.7
22.7
22.7
22.7
1
2
2
2
3
3
3
3
4
4
4
4
457
305
356
406
254
305
356
406
203
254
305
356
708
703
724
781
629
678
724
781
573
629
678
724
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
2101390
2101392
2101394
2101396
2101400
2101402
2101404
2101406
2101410
2101412
2101414
2101416
27.2
27.2
27.2
27.2
27.2
27.2
27.2
27.2
27.2
27.2
27.2
27.2
2
2
2
2
3
3
3
3
4
4
4
4
305
356
406
457
254
305
356
406
254
305
356
406
765
813
873
917
718
765
813
873
917
765
813
873
108
108
108
108
108
108
108
108
108
108
108
108
C35D12BP
C35D14BP
C35D16BP
C35D18BP
C35T 10BP
C35T 12BP
C35T 14BP
C35T 16BP
C35Q10BP
C35Q12BP
C35Q14BP
C35Q16BP
2101450
2101452
2101454
2101456
2101460
2101462
2101464
2101466
2101470
2101472
2101474
2101476
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
2
2
2
2
3
3
3
3
4
4
4
4
406
406
406
457
254
305
356
406
254
305
356
406
765
813
873
917
718
765
813
873
917
765
813
873
108
108
108
108
108
108
108
108
108
108
108
108
C40D18BP
C40D20BP
C40D24BP
C40T 14BP
C40T 16BP
C40T 18BP
C40T 20BP
C40Q12BP
C40Q14BP
C40Q16BP
C40Q18BP
2101512
2101514
2101516
2101520
2101522
2101524
2101526
2101530
2101532
2101534
2101536
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
2
2
2
3
3
3
3
4
4
4
4
457
508
610
356
406
457
508
305
356
406
457
940
972
1073
870
927
940
972
822
870
927
940
108
108
108
127
127
108
108
127
127
127
108
C45D18BP
C45D20BP
C45D24BP
C45T 14BP
C45T 16BP
C45T 18BP
C45T 20BP
C45Q12BP
C45Q14BP
C45Q16BP
C45Q18BP
2101582
2101584
2101586
2101590
2101592
2101594
2101596
2101600
2101602
2101604
2101606
40.8
40.8
40.8
40.8
40.8
40.8
40.8
40.8
40.8
40.8
40.8
2
2
2
3
3
3
3
4
4
4
4
457
508
610
356
406
457
508
305
356
406
457
940
972
1073
870
927
940
972
822
870
927
940
108
108
108
127
127
108
108
127
127
127
108
23
r25P
F
27
r30P
F
32
r35P
F
36
r40P
F
40
r45P
F
45
r50P
F
All Rights Reserved
C
D
169
19.1
169
19.1
169
19.1
227
19.1
227
19.1
227
19.1
227
19.1
Tonnes
64.5 12.7
110
12.7
110
12.7
110
12.7
169
12.7
169
12.7
169
12.7
169
12.7
227
12.7
227
12.7
227
12.7
227
12.7
Tonnes
136
52.3
136
52.3
136
52.3
136
52.3
169
52.3
169
52.3
169
52.3
169
52.3
227
52.3
227
52.3
227
52.3
227
52.3
Tonnes
136
42.9
136
42.9
136
42.9
136
42.9
169
42.9
169
42.9
169
42.9
169
42.9
227
42.9
227
42.9
227
42.9
227
42.9
Tonnes
148
31.8
148
31.8
148
31.8
169
31.8
169
31.8
213
31.8
213
31.8
227
31.8
227
31.8
227
31.8
288
31.8
Tonnes
148
25.4
148
25.4
148
25.4
169
25.4
169
25.4
213
25.4
213
25.4
227
25.4
227
25.4
227
25.4
288
25.4
Tonnes
Weigh t
Each
(kg .)
94
116
140
78
99
119
142
E
207
207
207
265
265
265
265
F
308
359
409
206
257
308
359
G
22.4
22.4
22.4
22.4
22.4
22.4
22.4
H
24.6
24.6
24.6
24.6
24.6
24.6
24.6
I
29.0
29.0
29.0
29.0
29.0
29.0
29.0
J
71.5
71.5
71.5
71.5
71.5
71.5
71.5
K
51.0
51.0
51.0
51.0
51.0
51.0
51.0
X
58.5
58.5
58.5
58.5
58.5
58.5
58.5
103
148
148
148
207
207
207
207
265
265
265
265
460
308
359
409
257
308
359
409
206
257
308
359
22.4
22.4
22.4
22.4
22.4
22.4
22.4
22.4
22.4
22.4
22.4
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
29.0
29.0
29.0
29.0
29.0
29.0
29.0
29.0
29.0
29.0
29.0
79.0
71.5
71.5
71.5
71.5
71.5
71.5
71.5
71.5
71.5
71.5
71.5
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
58.5
58.5
58.5
58.5
58.5
58.5
58.5
58.5
58.5
58.5
58.5
92
76
90
108
81
94
115
140
76
101
119
142
174
174
174
174
207
207
207
207
265
265
265
265
308
359
409
460
257
308
359
409
257
308
359
409
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
107
107
107
107
107
107
107
107
107
107
107
107
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
71.0
71.0
71.0
71.0
58.5
58.5
58.5
58.5
58.5
58.5
58.5
58.5
86
103
121
156
97
108
128
156
116
132
155
189
174
174
174
174
207
207
207
207
265
265
265
265
308
359
409
460
257
308
359
409
257
308
359
409
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
107
107
107
107
107
107
107
107
107
107
107
107
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
71.0
71.0
71.0
71.0
58.5
58.5
58.5
58.5
58.5
58.5
58.5
58.5
86
102
121
156
97
108
128
156
116
132
155
189
199
199
199
207
207
264
264
265
265
265
339
460
511
613
359
409
460
511
308
359
409
460
28.7
28.7
28.7
28.7
28.7
28.7
28.7
28.7
28.7
28.7
28.7
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
107
107
107
107
107
107
107
107
107
107
107
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
84.0
84.0
84.0
58.5
58.5
73.5
73.5
58.5
58.5
58.5
73.5
217
257
338
136
163
264
313
144
164
195
310
199
199
199
207
207
264
264
265
265
265
339
460
511
613
359
409
460
511
308
359
409
460
28.7
28.7
28.7
28.7
28.7
28.7
28.7
28.7
28.7
28.7
28.7
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
107
107
107
107
107
107
107
107
107
107
107
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
84.0
84.0
84.0
58.5
58.5
73.5
73.5
58.5
58.5
58.5
73.5
217
257
338
136
163
264
313
144
164
195
310
263
McKissick®
Blocks
Mo del
No.
C20T 12BP
C20T 14BP
C20T 16BP
C20Q8BP
C20Q10BP
C20Q12BP
C20Q14BP
680-P
Inqu iry
Sto ck No .
2101262
2101264
2101266
2101270
2101272
2101274
2101276
Mo del
No.
C50D20BP
C50D24BP
C 50T 18BP
C 50T 20BP
C 50T 24BP
C50Q16BP
C50Q18BP
680-P
Inqu iry
Sto ck No .
2101640
2101642
2101650
2101652
2101654
2101660
2101662
Wo rking
L oad
L imit
(t)
45.4
45.4
45.4
45.4
45.4
45.4
45.4
C55D20BP
C55D24BP
C 55T 18BP
C 55T 20BP
C 55T 24BP
C55Q16BP
C55Q18BP
2101700
2101702
2101710
2101712
2101714
2101720
2101722
C 60T 18BP
C 60T 20BP
C 60T 24BP
C60Q18BP
C60Q20BP
C60Q24BP
B lo cks with Bo lt On ly Dimen sio ns
(mm)
No. of
Sheaves
2
2
3
3
3
4
4
Sheave
Diam .
(mm)
508
610
457
508
610
406
457
A
1067
1168
1035
1067
1168
981
1035
B
140
140
140
140
140
140
140
49.9
49.9
49.9
49.9
49.9
49.9
49.9
2
2
3
3
3
4
4
508
610
457
508
610
406
457
1067
1168
1035
1067
1168
981
1035
140
140
140
140
140
140
140
2101760
2101762
2101764
2101770
2101772
2101774
54.4
54.4
54.4
54.4
54.4
54.4
3
3
3
4
4
4
457
508
610
457
508
610
1035
1067
1168
1035
1067
1168
140
140
140
140
140
140
C 65T 18BP
C 65T 20BP
C 65T 24BP
C65Q18BP
C65Q20BP
C65Q24BP
2101810
2101812
2101814
2101820
2101822
2101824
59.0
59.0
59.0
59.0
59.0
59.0
3
3
3
4
4
4
457
508
610
457
508
610
1035
1067
1168
1035
1067
1168
140
140
140
140
140
140
C 70T 20BP
C70Q20BP
C70Q24BP
C70QN20BP
C70QN24BP
2101830
2101840
2101842
2101850
2101852
63
63
63
63
63
3
4
4
5
5
508
508
610
508
610
1175
1175
1276
1175
1276
178
178
178
178
178
C 80T 20BP
C80Q20BP
C80Q24BP
C80QN20BP
C80QN24BP
2101860
2101870
2101872
2101880
2101882
72
72
72
72
72
3
4
4
5
5
508
508
610
508
610
1175
1175
1276
1175
1276
178
178
178
178
178
C90Q20BP
C90Q24BP
C90QN20BP
C90QN24BP
2101920
2101922
2101930
2101932
81
81
81
81
4
4
5
5
508
610
508
610
1175
1276
1175
1276
191
191
191
191
C100QN20BP
C100QN24BP
C100SX20BP
C100SX24BP
2101970
2101972
2101980
2101982
90
90
90
90
5
5
6
6
508
610
508
610
1175
1276
1175
1276
191
191
191
191
50
r5P
F
54
r60P
F
59
r65P
F
63
r70P
F
72
r80P
F
81
r90P
F
90
r10P
F
264
C
D
148
44.5
148
44.5
213
44.5
213
44.5
213
44.5
288
44.5
288
44.5
Tonnes
148
39.6
148
39.6
213
39.6
213
39.6
213
39.6
288
39.6
288
39.6
Tonnes
213
35.1
213
35.1
213
35.1
288
35.1
288
35.1
288
35.1
Tonnes
213
30.2
213
30.2
213
30.2
288
30.2
288
30.2
288
30.2
Tonnes
232
44.5
287
44.5
287
44.5
232
44.5
232
44.5
Tonnes
232
36.6
287
36.6
287
36.6
232
36.6
232
36.6
Tonnes
287
30.2
287
30.2
232
30.2
232
30.2
Tonnes
232
25.4
232
25.4
287
25.4
287
25.4
Weig ht
Each
(kg .)
279
362
271
322
419
271
339
E
199
199
264
264
264
339
339
F
511
613
460
511
613
409
460
G
31.8
31.8
31.8
31.8
31.8
31.8
31.8
H
35.1
35.1
35.1
35.1
35.1
35.1
35.1
I
41.1
41.1
41.1
41.1
41.1
41.1
41.1
J
124
124
124
124
124
124
124
K
89.0
89.0
89.0
89.0
89.0
89.0
89.0
X
84.0
84.0
73.5
73.5
73.5
73.5
73.5
199
199
264
264
264
339
339
511
613
460
511
613
409
460
31.8
31.8
31.8
31.8
31.8
31.8
31.8
35.1
35.1
35.1
35.1
35.1
35.1
35.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
124
124
124
124
124
124
124
89.0
89.0
89.0
89.0
89.0
89.0
89.0
84.0
84.0
73.5
73.5
73.5
73.5
73.5
279
362
271
322
419
271
339
264
264
264
339
339
339
460
511
613
460
511
613
31.8
31.8
31.8
31.8
31.8
31.8
35.1
35.1
35.1
35.1
35.1
35.1
41.1
41.1
41.1
41.1
41.1
41.1
124
124
124
124
124
124
89.0
89.0
89.0
89.0
89.0
89.0
73.5
73.5
73.5
73.5
73.5
73.5
271
322
419
339
407
503
264
264
264
339
339
339
460
511
613
460
511
613
31.8
31.8
31.8
31.8
31.8
31.8
35.1
35.1
35.1
35.1
35.1
35.1
41.1
41.1
41.1
41.1
41.1
41.1
124
124
124
124
124
124
89.0
89.0
89.0
89.0
89.0
89.0
73.5
73.5
73.5
73.5
73.5
73.5
271
322
419
339
407
503
283
338
338
463
463
511
511
613
511
613
35.1
35.1
35.1
35.1
35.1
38.1
38.1
38.1
38.1
38.1
46.2
46.2
46.2
46.2
46.2
142
142
142
142
142
102
102
102
102
102
3.30
2.90
2.90
3.30
3.30
404
424
572
592
778
283
338
338
463
463
511
511
613
511
613
35.1
35.1
35.1
35.1
35.1
38.1
38.1
38.1
38.1
38.1
46.2
46.2
46.2
46.2
46.2
142
142
142
142
142
102
102
102
102
102
3.30
2.90
2.90
3.30
3.30
404
424
572
592
778
338
338
463
463
511
613
511
613
35.1
35.1
35.1
35.1
38.1
38.1
38.1
38.1
46.2
46.2
46.2
46.2
142
142
142
142
102
102
102
102
2.90
2.90
3.30
3.30
481
644
592
805
463
463
518
518
511
613
511
613
35.1
35.1
35.1
35.1
38.1
38.1
38.1
38.1
46.2
46.2
46.2
46.2
142
142
142
142
102
102
102
102
3.30
3.30
2.90
2.90
592
805
619
841
All Rights Reserved
McKissick®Construction Blocks
s k c o l B
n o i t c u r t s n o C® k c i s s i K c M
%/2&.6
+),77,1*
"H" Fitting - Blocks with Hanger - See Drawing on Page 261
Mod el
No.
680-H
In quiry
Stock
No .
Working
Load
No . o f
Limit
Sheaves
(t)
Sheave
Diam .
(mm)
Blocks with Hangers - Dimension s
(mm)
A
E
F
G
4.5 Tonnes
155
206
155
16.0
206
16.0
155
16.0
206
16.0
6.8 Tonnes
155
206
155
16.0
206
16.0
155
16.0
206
16.0
9 Tonnes
206
257
308
359
155
16.0
206
16.0
257
16.0
308
16.0
359
16.0
206
16.0
257
16.0
308
16.0
359
16.0
206
16.0
257
16.0
13.6 Tonnes
257
308
359
257
19.1
308
19.1
359
19.1
206
19.1
257
19.1
308
19.1
359
19.1
257
19.1
18 Tonnes
460
308
22.4
359
22.4
409
22.4
257
22.4
308
22.4
H
I
L
M
N
O
P
Q
X
Weig ht
Each
(kg .)
17.5
17.5
17.5
17.5
21.3
21.3
21.3
21.3
41.4
41.4
41.4
41.4
41.4
41.4
31.8
31.8
31.8
31.8
31.8
31.8
26.9
26.9
26.9
26.9
26.9
26.9
29.5
29.5
29.5
29.5
29.5
29.5
82.5
82.5
82.5
82.5
82.5
82.5
47.2
47.2
57.0
57.0
57.0
57.0
51.5
51.5
51.5
51.5
10.0
15.4
16.8
26.3
23.1
36.7
17.5
17.5
17.5
17.5
21.3
21.3
21.3
21.3
41.4
41.4
41.4
41.4
41.4
41.4
31.8
31.8
31.8
31.8
31.8
31.8
26.9
26.9
26.9
26.9
26.9
26.9
29.5
29.5
29.5
29.5
29.5
29.5
82.5
82.5
82.5
82.5
82.5
82.5
47.2
47.2
57.0
57.0
57.0
57.0
51.5
51.5
51.5
51.5
10.0
15.4
16.8
26.3
23.1
36.7
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
21.3
21.3
21.3
21.3
21.3
21.3
21.3
21.3
21.3
21.3
21.3
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
102
102
102
102
102
102
102
102
102
102
102
102
102
102
102
53.0
53.0
53.0
53.0
68.0
68.0
68.0
68.0
68.0
88.0
88.0
88.0
88.0
92.0
92.0
51.5
51.5
51.5
51.5
51.5
51.5
51.5
51.5
51.5
51.5
51.5
17.7
23.6
28.1
31.3
20.0
29.5
40.4
48.1
55
40.8
56
67
78
52
73
20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
66.5
66.5
66.5
66.5
66.5
66.5
66.5
66.5
66.5
66.5
66.5
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
39.6
39.6
39.6
39.6
39.6
39.6
39.6
39.6
39.6
39.6
39.6
54.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
140
140
140
140
140
140
140
140
140
140
140
71.5
71.5
71.5
86.5
86.5
86.5
98.5
98.5
98.5
98.5
98.5
58.5
58.5
58.5
58.5
58.5
58.5
58.5
58.5
39.0
46.3
55
59
70
83
58
79
93
107
98
24.6
24.6
24.6
24.6
24.6
29.0
29.0
29.0
29.0
29.0
63.5
63.5
63.5
63.5
63.5
63.5
47.8
47.8
47.8
47.8
47.8
47.8
42.9
42.9
42.9
42.9
42.9
42.9
54.0
54.0
54.0
54.0
54.0
54.0
140
140
140
140
140
140
71.0
84.0
84.0
84.0
98.5
98.5
58.5
58.5
58.5
58.5
58.5
98
83
97
115
91
104
r5H
F
C5S6BH
C5S8BH
C 5D6BH
C 5D8BH
C5T6BH
C5T8BH
2102000
2102002
2102010
2102012
2102020
2102022
4.5
4.5
4.5
4.5
4.5
4.5
1
1
2
2
3
3
152
203
152
203
152
203
381
429
448
495
448
495
58.0
58.0
109
109
161
161
C7S6BH
C7S8BH
C 7D6BH
C 7D8BH
C7T6BH
C7T8BH
2102050
2102052
2102060
2102062
2102070
2102072
6.8
6.8
6.8
6.8
6.8
6.8
1
1
2
2
3
3
152
203
152
203
152
203
381
429
448
495
448
495
58.0
58.0
109
109
161
161
C10S8BH
C10S10BH
C10S12BH
C10S14BH
C10D6BH
C10D8BH
C10D10BH
C10D12BH
C10D14BH
C10T8BH
C10T10BH
C10T12BH
C10T14BH
C10Q8BH
C10Q10BH
2102100
2102102
2102104
2102106
2102110
2102112
2102114
2102116
2102118
2102120
2102122
2102124
2102126
2102130
2102132
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
1
1
1
1
2
2
2
2
2
3
3
3
3
4
4
203
254
305
356
152
203
254
305
356
203
254
305
356
203
254
467
518
565
619
481
526
576
624
678
526
576
624
678
526
576
58.0
58.0
58.0
58.0
109
109
109
109
109
161
161
161
161
213
213
C15S10BH
C15S12BH
C15S14BH
C15D10BH
C15D12BH
C15D14BH
C15T8BH
C15T10BH
C15T12BH
C15T14BH
C15Q10BH
2102170
2102172
2102174
2102180
2102182
2102184
2102190
2102192
2102194
2102196
2102200
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
1
1
1
2
2
2
3
3
3
3
4
254
305
356
254
305
356
203
254
305
356
254
602
649
700
678
725
776
627
678
725
776
678
77.0
77.0
77.0
136
136
136
194
194
194
194
252
C20S18BH
C20D12BH
C20D14BH
C20D16BH
C20T10BH
C20T12BH
2102244
2102250
2102252
2102254
2102260
2102262
18.1
18.1
18.1
18.1
18.1
18.1
1
2
2
2
3
3
457
305
356
406
254
305
819
814
835
893
740
789
103
148
148
148
207
207
r7.5H
F
McKissick®
Blocks
r10H
F
r15H
F
r20H
F
All Rights Reserved
265
Working
Load
No . o f
Limit
Sheaves
(t)
18.1
3
18.1
3
18.1
4
18.1
4
18.1
4
18.1
4
(mm)
Mod el
No.
C20T14BH
C20T16BH
C20Q8BH
C20Q10BH
C20Q12BH
C20Q14BH
680-H
In quiry
Stock
N o.
2102264
2102266
2102270
2102272
2102274
2102276
C25S18BH
C25D12BH
C25D14BH
C25D16BH
C25T10BH
C25T12BH
C25T14BH
C25T16BH
C25Q8BH
C25Q10BH
C25Q12BH
C25Q14BH
2102314
2102320
2102322
2102324
2102330
2102332
2102334
2102336
2102340
2102342
2102344
2102346
22.7
22.7
22.7
22.7
22.7
22.7
22.7
22.7
22.7
22.7
22.7
22.7
1
2
2
2
3
3
3
3
4
4
4
4
457
305
356
406
254
305
356
406
203
254
305
356
819
814
835
893
740
789
835
892
684
740
789
835
103
148
148
148
207
207
207
207
265
265
265
265
C30D12BH
C30D14BH
C30D16BH
C30D18BH
C30T10BH
C30T12BH
C30T14BH
C30T16BH
C30Q10BH
C30Q12BH
C30Q14BH
C30Q16BH
2102390
2102392
2102394
2102396
2102400
2102402
2102404
2102406
2102410
2102412
2102414
2102416
27.2
27.2
27.2
27.2
27.2
27.2
27.2
27.2
27.2
27.2
27.2
27.2
2
2
2
2
3
3
3
3
4
4
4
4
305
356
406
457
254
305
356
406
254
305
356
406
899
946
1006
1051
851
899
946
1006
1051
899
946
1006
174
174
174
174
207
207
207
207
265
265
265
265
C35D12BH
C35D14BH
C35D16BH
C35D18BH
C35T10BH
C35T12BH
C35T14BH
C35T16BH
C35Q10BH
C35Q12BH
C35Q14BH
C35Q16BH
2102450
2102452
2102454
2102456
2102460
2102462
2102464
2102466
2102470
2102472
2102474
2102476
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
2
2
2
2
3
3
3
3
4
4
4
4
305
356
406
457
254
305
356
406
254
305
356
406
899
946
1006
1051
851
899
946
1006
1051
899
946
1006
174
174
174
174
207
207
207
207
265
265
265
265
C40D18BH
C40D20BH
C40D24BH
C40T14BH
C40T16BH
C40T18BH
C40T20BH
C40Q12BH
C40Q14BH
C40Q16BH
C40Q18BH
2102512
2102514
2102516
2102520
2102522
2102524
2102526
2102530
2102532
2102534
2102536
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
2
2
2
3
3
3
3
4
4
4
4
457
508
610
356
406
457
508
305
356
406
457
1089
1121
1222
1019
1076
1089
1121
972
1019
1076
1089
199
199
199
207
207
264
264
265
265
265
339
C45D18BH
C45D20BH
C45D24BH
C45T14BH
C45T16BH
C45T18BH
C45T20BH
C45Q12BH
C45Q14BH
C45Q16BH
C45Q18BH
2102582
2102584
2102586
2102590
2102592
2102594
2102596
2102600
2102602
2102604
2102606
40.8
40.8
40.8
40.8
40.8
40.8
40.8
40.8
40.8
40.8
40.8
2
2
2
3
3
3
3
4
4
4
4
457
508
610
356
406
457
508
305
356
406
457
1089
1121
1222
1019
1076
1089
1121
972
1019
1076
1089
199
199
199
207
207
264
264
265
265
265
339
Sheave
Diam.
(mm)
356
406
203
254
305
356
A
835
892
684
740
789
835
E
207
207
265
265
265
265
F
G
359 22.4
409 22.4
206 22.4
257 22.4
308 22.4
359 22.4
23 Tonnes
460
308 22.4
359 22.4
409 22.4
257 22.4
308 22.4
359 22.4
409 22.4
206 22.4
257 22.4
308 22.4
359 22.4
27 Tonnes
308 25.4
359 25.4
409 25.4
460 25.4
257 25.4
308 25.4
359 25.4
409 25.4
257 25.4
308 25.4
359 25.4
409 25.4
32 Tonnes
308 25.4
359 25.4
409 25.4
460 25.4
257 25.4
308 25.4
359 25.4
409 25.4
257 25.4
308 25.4
359 25.4
409 25.4
36 Tonnes
460 28.7
511 28.7
613 28.7
359 28.7
409 28.7
460 28.7
511 28.7
308 28.7
359 28.7
409 28.7
460 28.7
40 Tonnes
460 28.7
511 28.7
613 28.7
359 28.7
409 28.7
460 28.7
511 28.7
308 28.7
359 28.7
409 28.7
460 28.7
45 Tonnes
Weig ht
Each
(kg .)
125
149
89
112
130
153
H
24.6
24.6
24.6
24.6
24.6
24.6
I
29.0
29.0
29.0
29.0
29.0
29.0
L
63.5
63.5
63.5
63.5
63.5
63.5
M
47.8
47.8
47.8
47.8
47.8
47.8
N
42.9
42.9
42.9
42.9
42.9
42.9
O
54.0
54.0
54.0
54.0
54.0
54.0
P
140
140
140
140
140
140
Q
98.5
98.5
98.5
98.5
98.5
98.5
X
58.5
58.5
58.5
58.5
58.5
58.5
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
29.0
29.0
29.0
29.0
29.0
29.0
29.0
29.0
29.0
29.0
29.0
63.5
63.5
63.5
63.5
63.5
63.5
63.5
63.5
63.5
63.5
63.5
63.5
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
54.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
54.0
140
140
140
140
140
140
140
140
140
140
140
140
71.0
84.0
84.0
84.0
98.5
98.5
98.5
98.5
98.5
98.5
98.5
98.5
58.5
58.5
58.5
58.5
58.5
58.5
58.5
58.5
58.5
58.5
58.5
98
83
97
115
91
104
125
149
89
112
130
153
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
70.0
70.0
70.0
70.0
70.0
70.0
70.0
70.0
70.0
70.0
70.0
70.0
63.5
63.5
63.5
63.5
63.5
63.5
63.5
63.5
63.5
63.5
63.5
63.5
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
178
178
178
178
178
178
178
178
178
178
178
178
97.5
97.5
97.5
97.5
108
108
108
108
108
108
108
108
71.0
71.0
71.0
71.0
58.5
58.5
58.5
58.5
58.5
58.5
58.5
58.5
102
118
137
172
115
127
146
174
139
155
178
213
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
70.0
70.0
70.0
70.0
70.0
70.0
70.0
70.0
70.0
70.0
70.0
70.0
63.5
63.5
63.5
63.5
63.5
63.5
63.5
63.5
63.5
63.5
63.5
63.5
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
42.9
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
178
178
178
178
178
178
178
178
178
178
178
178
97.5
97.5
97.5
97.5
108
108
108
108
108
108
108
108
71.0
71.0
71.0
71.0
58.5
58.5
58.5
58.5
58.5
58.5
58.5
58.5
102
118
137
172
115
127
146
174
139
155
178
213
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
73.0
73.0
73.0
73.0
73.0
73.0
73.0
73.0
73.0
73.0
73.0
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
70.0
70.0
70.0
70.0
70.0
70.0
70.0
70.0
70.0
70.0
70.0
184
184
184
203
203
184
184
203
203
203
184
106
106
106
114
114
114
114
133
133
133
114
84.0
84.0
84.0
58.5
58.5
73.5
73.5
58.5
58.5
58.5
73.5
239
280
361
161
189
293
343
176
196
227
347
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
76.0
73.0
73.0
73.0
73.0
73.0
73.0
73.0
73.0
73.0
73.0
73.0
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
52.5
70.0
70.0
70.0
70.0
70.0
70.0
70.0
70.0
70.0
70.0
70.0
184
184
184
203
203
184
184
203
203
203
184
106
106
106
114
114
114
114
133
133
133
114
84.0
84.0
84.0
58.5
58.5
73.5
73.5
58.5
58.5
58.5
73.5
239
280
361
161
189
293
343
176
196
227
347
r25H
F
r30H
F
r35H
F
r40H
F
r45H
F
r50H
F
266
All Rights Reserved
(mm)
Mod el
No.
C50D20BH
C50D24BH
C50T18BH
C50T20BH
C50T24BH
C50Q16BH
C50Q18BH
680-H
Working
In quiry
Load
No . o f
Stock
Limit
Sheaves
No .
(t)
2102640
45.4
2
2102642
45.4
2
2102650
45.4
3
2102652
45.4
3
2102654
45.4
3
2102660
45.4
4
2102662
45.4
4
C55D20BH
C55D24BH
C55T18BH
C55T20BH
C55T24BH
C55Q16BH
C55Q18BH
2102700
2102702
2102710
2102712
2102714
2102720
2102722
49.9
49.9
49.9
49.9
49.9
49.9
49.9
2
2
3
3
3
4
4
508
610
457
508
610
406
457
1238
1340
1207
1238
1340
1153
1194
199
199
264
264
264
339
339
C60T18BH
C60T20BH
C60T24BH
C60Q18BH
C60Q20BH
C60Q24BH
2102760
2102762
2102764
2102770
2102772
2102774
54.4
54.4
54.4
54.4
54.4
54.4
3
3
3
4
4
4
457
508
610
457
508
610
1216
1248
1349
1216
1248
1349
264
264
264
339
339
339
C65T18BH
C65T20BH
C65T24BH
C65Q18BH
C65Q20BH
C65Q24BH
2102810
2102812
2102814
2102820
2102822
2102824
59.0
59.0
59.0
59.0
59.0
59.0
3
3
3
4
4
4
457
508
610
457
508
610
1216
1248
1349
1216
1248
1349
264
264
264
339
339
339
C70T20BH
C70Q20BH
C70Q24BH
C70QN20BH
C70QN24BH
2102830
2102840
2102842
2102850
2102852
63
63
63
63
63
3
4
4
5
5
508
508
610
508
610
1407
1407
1508
1407
1508
283
338
338
463
463
C80T20BH
C80Q20BH
C80Q24BH
C80QN20BH
C80QN24BH
2102860
2102870
2102872
2102880
2102882
72
72
72
72
72
3
4
4
5
5
508
508
610
508
610
1407
1407
1508
1407
1508
283
338
338
463
463
C90Q20BH
C90Q24BH
C90QN20BH
C90QN24BH
2102920
2102922
2102930
2102932
81
81
81
81
4
4
5
5
508
610
508
610
1407
1508
1407
1508
351
351
463
463
C100QN20BH
C100QN24BH
C 100SX20BH
C 100SX24BH
2102970
2102972
2102980
2102982
90
90
90
90
5
5
6
6
508
610
508
610
1407
1508
1407
1508
463
463
518
518
Sheave
Diam .
(mm)
508
610
457
508
610
406
457
A
1238
1340
1207
1238
1340
1153
1207
E
199
199
264
264
264
339
339
F
G
511
31.8
613
31.8
460
31.8
511
31.8
613
31.8
409
31.8
460
31.8
50 Tonnes
511
31.8
613
31.8
460
31.8
511
31.8
613
31.8
409
31.8
460
31.8
54 Tonnes
460
31.8
511
31.8
613
31.8
460
31.8
511
31.8
613
31.8
59 Tonnes
460
31.8
511
31.8
613
31.8
460
31.8
511
31.8
613
31.8
63 Tonnes
511
35.1
511
35.1
613
35.1
511
35.1
613
35.1
72 Tonnes
511
35.1
511
35.1
613
35.1
511
35.1
613
35.1
81 Tonnes
511
35.1
613
35.1
511
35.1
613
35.1
90 Tonnes
511
35.1
613
35.1
511
35.1
613
35.1
Weig ht
Each
(kg .)
312
395
318
368
465
330
398
H
35.1
35.1
35.1
35.1
35.1
35.1
35.1
I
41.1
41.1
41.1
41.1
41.1
41.1
41.1
L
89.0
89.0
89.0
89.0
89.0
89.0
89.0
M
82.5
82.5
82.5
82.5
82.5
82.5
82.5
N
58.5
58.5
58.5
58.5
58.5
58.5
58.5
O
76.0
76.0
76.0
76.0
76.0
76.0
76.0
P
229
229
229
229
229
229
229
Q
116
116
139
139
139
149
149
X
84.0
84.0
73.5
73.5
73.5
73.5
73.5
35.1
35.1
35.1
35.1
35.1
35.1
35.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
89.0
89.0
89.0
89.0
89.0
89.0
89.0
82.5
82.5
82.5
82.5
82.5
82.5
82.5
58.5
58.5
58.5
58.5
58.5
58.5
58.5
76.0
76.0
76.0
76.0
76.0
76.0
76.0
229
229
229
229
229
229
229
116
116
139
139
139
149
149
84.0
84.0
73.5
73.5
73.5
73.5
73.5
312
395
318
368
465
330
398
35.1
35.1
35.1
35.1
35.1
35.1
41.1
41.1
41.1
41.1
41.1
41.1
89.0
89.0
89.0
89.0
89.0
89.0
92.0
92.0
92.0
92.0
92.0
92.0
58.5
58.5
58.5
58.5
58.5
58.5
76.0
76.0
76.0
76.0
76.0
76.0
229
229
229
229
229
229
139
139
139
149
149
149
73.5
73.5
73.5
73.5
73.5
73.5
318
368
465
398
466
562
35.1
35.1
35.1
35.1
35.1
35.1
41.1
41.1
41.1
41.1
41.1
41.1
89.0
89.0
89.0
89.0
89.0
89.0
92.0
92.0
92.0
92.0
92.0
92.0
58.5
58.5
58.5
58.5
58.5
58.5
76.0
76.0
76.0
76.0
76.0
76.0
229
229
229
229
229
229
139
139
139
149
149
149
73.5
73.5
73.5
73.5
73.5
73.5
318
368
465
398
466
562
38.1
38.1
38.1
38.1
38.1
46.2
46.2
46.2
46.2
46.2
114
114
114
114
114
117
117
117
117
117
71.4
71.4
71.4
71.4
71.4
95.3
95.3
95.3
95.3
95.3
292
292
292
292
292
163
184
184
163
163
83.8
73.7
73.7
83.8
83.8
485
515
662
676
862
38.1
38.1
38.1
38.1
38.1
46.2
46.2
46.2
46.2
46.2
114
114
114
114
114
117
117
117
117
117
71.4
71.4
71.4
71.4
71.4
95.3
95.3
95.3
95.3
95.3
292
292
292
292
292
163
184
184
163
163
83.8
73.7
73.7
83.8
83.8
485
515
662
676
862
38.1
38.1
38.1
38.1
46.2
46.2
46.2
46.2
114
114
114
114
117
117
117
117
71.4
71.4
71.4
71.4
95.3
95.3
95.3
95.3
292
292
292
292
176
176
154
154
73.7
73.7
83.8
83.8
572
735
676
889
38.1
38.1
38.1
38.1
46.2
46.2
46.2
46.2
114
114
114
114
117
117
117
117
71.4
71.4
71.4
71.4
95.3
95.3
95.3
95.3
292
292
292
292
154
154
176
176
83.8
83.8
73.7
73.7
676
889
710
932
r5H
F
r60H
F
r65H
F
r70H
F
McKissick®
Blocks
r80H
F
r90H
F
r10H
F
All Rights Reserved
267
s k c o l B
n o i t c u r t s n o C® k c i s s i K c M
%/2&.6
6),77,1*
"S" Fitting - Blocks with Hanger & Shackle - See Drawing on Page 261
Mod el
No.
680-S
In quiry
Stock
N o.
Working
Load
No . o f
Limit
Sheaves
(t)
Sheave
Diam.
(mm)
Blo cks with Hang er and Sh ackle - Dimen sio ns
(mm)
A
E
F
G
4.5 Tonnes
155
-206
-155
16.0
206
16.0
155
16.0
206
16.0
6.8 Tonnes
155
-206
-155
16.0
206
16.0
155
16.0
206
16.0
9 Tonnes
206
-257
-308
-359
-155
16.0
206
16.0
257
16.0
308
16.0
359
16.0
206
16.0
257
16.0
308
16.0
359
16.0
206
16.0
257
16.0
13.6 Tonnes
257
-308
-359
-257
19.1
308
19.1
359
19.1
206
19.1
257
19.1
308
19.1
359
19.1
257
19.1
18 Tonnes
460
-308
22.4
359
22.4
409
22.4
257
22.4
308
22.4
359
22.4
Weigh t
Each
(kg.)
H
I
S
T
U
V
W
X
--17.5
17.5
17.5
17.5
--21.3
21.3
21.3
21.3
97.0
97.0
97.0
97.0
97.0
97.0
65.0
65.0
65.0
65.0
65.0
65.0
29.0
29.0
29.0
29.0
29.0
29.0
22.4
22.4
22.4
22.4
22.4
22.4
24.6
24.6
24.6
24.6
24.6
24.6
--51.5
51.5
51.5
51.5
11.3
16.8
18.1
27.7
24.5
38.1
--17.5
17.5
17.5
17.5
--21.3
21.3
21.3
21.3
97.0
97.0
97.0
97.0
97.0
97.0
65.0
65.0
65.0
65.0
65.0
65.0
29.0
29.0
29.0
29.0
29.0
29.0
22.4
22.4
22.4
22.4
22.4
22.4
24.6
24.6
24.6
24.6
24.6
24.6
--51.5
51.5
51.5
51.5
11.3
16.8
18.1
27.7
24.5
38.1
----17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
17.5
----21.3
21.3
21.3
21.3
21.3
21.3
21.3
21.3
21.3
21.3
21.3
124
124
124
124
124
124
124
124
124
124
124
124
124
124
124
89.0
89.0
89.0
89.0
89.0
89.0
89.0
89.0
89.0
89.0
89.0
89.0
89.0
89.0
89.0
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
28.7
28.7
28.7
28.7
28.7
28.7
28.7
28.7
28.7
28.7
28.7
28.7
28.7
28.7
28.7
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
----51.5
51.5
51.5
51.5
51.5
51.5
51.5
51.5
51.5
51.5
51.5
21.3
27.2
31.8
34.9
23.6
33.1
44.0
52
59
44.0
60
70
81
56
77
---20.6
20.6
20.6
20.6
20.6
20.6
20.6
20.6
---25.4
25.4
25.4
25.4
25.4
25.4
25.4
25.4
152
152
152
152
152
152
152
152
152
152
152
105
105
105
105
105
105
105
105
105
105
105
46.0
46.0
46.0
46.0
46.0
46.0
46.0
46.0
46.0
46.0
46.0
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
---58.5
58.5
58.5
58.5
58.5
58.5
58.5
58.5
46.3
54
62
67
77
91
65
86
100
114
105
-24.6
24.6
24.6
24.6
24.6
24.6
-29.0
29.0
29.0
29.0
29.0
29.0
167
167
167
167
167
167
167
119
119
119
119
119
119
119
49.3
49.3
49.3
49.3
49.3
49.3
49.3
38.1
38.1
38.1
38.1
38.1
38.1
38.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
-58.5
58.5
58.5
58.5
58.5
58.5
107
92
107
125
100
113
134
r5S
F
C5S6BS
C5S8BS
C5D6BS
C5D8BS
C5T6BS
C5T8BS
2103000
2103002
2103010
2103012
2103020
2103022
4.5
4.5
4.5
4.5
4.5
4.5
1
1
2
2
3
3
152
203
152
203
152
203
471
519
538
586
538
586
58.0
58.0
109
109
161
161
C7S6BS
C7S8BS
C7D6BS
C7D8BS
C7T6BS
C7T8BS
2103050
2103052
2103060
2103062
2103070
2103072
6.8
6.8
6.8
6.8
6.8
6.8
1
1
2
2
3
3
152
203
152
203
152
203
471
519
538
586
538
586
58.0
58.0
109
109
161
161
C10S8BS
C10S10BS
C10S12BS
C10S14BS
C10D6BS
C10D8BS
C10D10BS
C10D12BS
C10D14BS
C10T8BS
C10T10BS
C10T12BS
C10T14BS
C10Q8BS
C10Q10BS
2103100
2103102
2103104
2103106
2103110
2103112
2103114
2103116
2103118
2103120
2103122
2103124
2103126
2103130
2103132
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
9.1
1
1
1
1
2
2
2
2
2
3
3
3
3
4
4
203
254
305
356
152
203
254
305
356
203
254
305
356
203
254
587
638
686
740
602
646
697
744
799
646
697
744
799
646
697
58.0
58.0
58.0
58.0
109
109
109
109
109
161
161
161
161
213
213
C15S10BS
C15S12BS
C15S14BS
C15D10BS
C15D12BS
C15D14BS
C15T8BS
C15T10BS
C15T12BS
C15T14BS
C15Q10BS
2103170
2103172
2103174
2103180
2103182
2103184
2103190
2103192
2103194
2103196
2103200
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
13.6
1
1
1
2
2
2
3
3
3
3
4
254
305
356
254
305
356
203
254
305
356
254
744
792
843
821
868
919
770
821
868
919
821
77.0
77.0
77.0
136
136
136
194
194
194
194
252
C20S18BS
C20D12BS
C20D14BS
C20D16BS
C20T10BS
C20T12BS
C20T14BS
2103244
2103250
2103252
2103254
2103260
2103262
2103264
18.1
18.1
18.1
18.1
18.1
18.1
18.1
1
2
2
2
3
3
3
457
305
356
406
254
305
356
979
975
995
1053
900
949
995
103
148
148
148
207
207
207
r7.5S
F
r10S
F
r15S
F
r20S
F
268
All Rights Reserved
Mod el
No.
C20T16BS
C20Q8BS
C20Q10BS
C20Q12BS
C20Q14BS
680-S
Working
In quiry
Load
No . o f
Stock
Limit
Sheaves
No .
(t)
2103266
18.1
3
2103270
18.1
4
2103272
18.1
4
2103274
18.1
4
2103276
18.1
4
Blo cks with Hang er and Shackle - Dimen sio ns
(mm)
C25S18BS
C25D12BS
C25D14BS
C25D16BS
C25T10BS
C25T12BS
C25T14BS
C25T16BS
C25Q8BS
C25Q10BS
C25Q12BS
C25Q14BS
2103314
2103320
2103322
2103324
2103330
2103332
2103334
2103336
2103340
2103342
2103344
2103346
22.7
22.7
22.7
22.7
22.7
22.7
22.7
22.7
22.7
22.7
22.7
22.7
1
2
2
2
3
3
3
3
4
4
4
4
457
305
356
406
254
305
356
406
203
254
305
356
979
975
995
1053
900
949
995
1053
845
900
949
995
103
148
148
148
207
207
207
207
265
265
265
265
C30D12BS
C30D14BS
C30D16BS
C30D18BS
C30T10BS
C30T12BS
C30T14BS
C30T16BS
C30Q10BS
C30Q12BS
C30Q14BS
C30Q16BS
2103390
2103392
2103394
2103396
2103400
2103402
2103404
2103406
2103410
2103412
2103414
2103416
27.2
27.2
27.2
27.2
27.2
27.2
27.2
27.2
27.2
27.2
27.2
27.2
2
2
2
2
3
3
3
3
4
4
4
4
305
356
406
457
254
305
356
406
254
305
356
406
1043
1091
1151
1195
995
1043
1091
1158
1195
1043
1091
1151
174
174
174
174
207
207
207
207
265
265
265
265
C35D12BS
C35D14BS
C35D16BS
C35D18BS
C35T10BS
C35T12BS
C35T14BS
C35T16BS
C35Q10BS
C35Q12BS
C35Q14BS
C35Q16BS
2103450
2103452
2103454
2103456
2103460
2103462
2103464
2103466
2103470
2103472
2103474
2103476
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
2
2
2
2
3
3
3
3
4
4
4
4
305
356
406
457
254
305
356
406
254
305
356
406
1043
1091
1151
1195
995
1043
1091
1151
1195
1043
1091
1151
174
174
174
174
207
207
207
207
265
265
265
265
C40D18BS
C40D20BS
C40D24BS
C40T14BS
C40T16BS
C40T18BS
C40T20BS
C40Q12BS
C40Q14BS
C40Q16BS
C40Q18BS
2103512
2103514
2103516
2103520
2103522
2103524
2103526
2103530
2103532
2103534
2103536
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
2
2
2
3
3
3
3
4
4
4
4
457
508
610
356
406
457
508
305
356
406
457
1276
1308
1410
1207
1264
1276
1308
1159
1207
1264
1276
199
199
199
207
207
264
264
265
265
265
339
C45D18BS
C45D20BS
C45D24BS
C45T14BS
C45T16BS
C45T18BS
C45T20BS
C45Q12BS
C45Q14BS
C45Q16BS
C45Q18BS
2103582
2103584
2103586
2103590
2103592
2103594
2103596
2103600
2103602
2103604
2103606
40.8
40.8
40.8
40.8
40.8
40.8
40.8
40.8
40.8
40.8
40.8
2
2
2
3
3
3
3
4
4
4
4
457
508
610
356
406
457
508
305
356
406
457
1276
1308
1410
1207
1264
1276
1308
1159
1207
1264
1276
199
199
199
207
207
264
264
265
265
265
339
C50D20BS
C50D24BS
2103640
2103642
45.4
45.4
2
2
508
610
1443
1545
199
199
Sheave
Diam .
(mm)
406
203
254
305
356
A
1053
845
900
949
995
E
207
265
265
265
265
F
G
409
22.4
206
22.4
257
22.4
308
22.4
359
22.4
23 Tonnes
460
-308
22.4
359
22.4
409
22.4
257
22.4
308
22.4
359
22.4
409
22.4
206
22.4
257
22.4
308
22.4
359
22.4
27 Tonnes
308
25.4
359
25.4
409
25.4
460
25.4
257
25.4
308
25.4
359
25.4
409
25.4
257
25.4
308
25.4
359
25.4
409
25.4
32 Tonnes
308
25.4
359
25.4
409
25.4
460
25.4
257
25.4
308
25.4
359
25.4
409
25.4
257
25.4
308
25.4
359
25.4
409
25.4
36 Tonnes
460
28.7
511
28.7
613
28.7
359
28.7
409
28.7
460
28.7
511
28.7
308
28.7
359
28.7
409
28.7
460
28.7
40 Tonnes
460
28.7
511
28.7
613
28.7
359
28.7
409
28.7
460
28.7
511
28.7
308
28.7
359
28.7
409
28.7
460
28.7
45 Tonnes
511
31.8
613
31.8
H
24.6
24.6
24.6
24.6
24.6
I
29.0
29.0
29.0
29.0
29.0
S
167
167
167
167
167
T
119
119
119
119
119
U
49.3
49.3
49.3
49.3
49.3
V
38.1
38.1
38.1
38.1
38.1
W
41.1
41.1
41.1
41.1
41.1
X
58.5
58.5
58.5
58.5
58.5
Weigh t
Each
(kg.)
159
98
122
140
162
-24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
24.6
-29.0
29.0
29.0
29.0
29.0
29.0
29.0
29.0
29.0
29.0
29.0
167
167
167
167
167
167
167
167
167
167
167
167
119
119
119
119
119
119
119
119
119
119
119
119
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
-58.5
58.5
58.5
58.5
58.5
58.5
58.5
58.5
58.5
58.5
58.5
107
92
107
125
100
113
134
159
98
122
140
162
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
167
167
167
167
167
167
167
167
167
167
167
167
93.5
93.5
93.5
93.5
93.5
93.5
93.5
93.5
93.5
93.5
93.5
93.5
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
71.0
71.0
71.0
71.0
71.0
71.0
71.0
71.0
71.0
71.0
71.0
71.0
111
127
147
181
124
136
156
184
148
165
188
177
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
26.9
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
34.0
167
167
167
167
167
167
167
167
167
167
167
167
93.5
93.5
93.5
93.5
93.5
93.5
93.5
93.5
93.5
93.5
93.5
93.5
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
49.3
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
38.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
71.0
71.0
71.0
71.0
71.0
71.0
58.5
58.5
58.5
58.5
58.5
58.5
111
127
147
181
124
136
156
184
148
165
188
222
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
203
203
203
203
203
203
203
203
203
203
203
130
130
130
130
130
130
130
130
130
130
130
63.5
63.5
63.5
63.5
63.5
63.5
63.5
63.5
63.5
63.5
63.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
84.0
84.0
84.0
58.5
58.5
73.5
73.5
58.5
58.5
58.5
73.5
255
295
376
177
204
308
358
191
211
243
363
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
37.1
203
203
203
203
203
203
203
203
203
203
203
130
130
130
130
130
130
130
130
130
130
130
63.5
63.5
63.5
63.5
63.5
63.5
63.5
63.5
63.5
63.5
63.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
44.5
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
84.0
84.0
84.0
58.5
58.5
73.5
73.5
58.5
58.5
58.5
73.5
255
295
376
177
204
308
358
191
211
243
363
35.1
35.1
41.1
41.1
226
226
143
143
73.0
73.0
51.0
51.0
61.0
61.0
84.0
84.0
336
419
r25S
F
r30S
F
r40S
F
r45S
F
r50S
F
All Rights Reserved
269
McKissick®
Blocks
r35S
F
Mod el
No.
C50T18BS
C50T20BS
C50T24BS
C50Q16BS
C50Q18BS
680-S
In quiry
Stock
N o.
2103650
2103652
2103654
2103660
2103662
Working
Load
No . o f
Limit
Sheaves
(t)
45.4
3
45.4
3
45.4
3
45.4
4
45.4
4
Blo cks with Hang er and Sh ackle - Dimen sio ns
(mm)
C55D20BS
C55D24BS
C55T18BS
C55T20BS
C55T24BS
C55Q16BS
C55Q18BS
2103700
2103702
2103710
2103712
2103714
2103720
2103722
49.9
49.9
49.9
49.9
49.9
49.9
49.9
2
2
3
3
3
4
4
508
610
457
508
610
406
457
1443
1545
1411
1443
1545
1357
1411
199
199
264
264
264
339
339
C60T18BS
C60T20BS
C60T24BS
C60Q18BS
C60Q20BS
C60Q24BS
2103760
2103762
2103764
2103770
2103772
2103774
54.4
54.4
54.4
54.4
54.4
54.4
3
3
3
4
4
4
457
508
610
457
508
610
1411
1441
1543
1411
1441
1543
264
264
264
339
339
339
C65T18BS
C65T20BS
C65T24BS
C65Q18BS
C65Q20BS
C65Q24BS
2103810
2103812
2103814
2103820
2103822
2103824
59.0
59.0
59.0
59.0
59.0
59.0
3
3
3
4
4
4
457
508
610
457
508
610
1411
1441
1543
1411
1441
1543
264
264
264
339
339
339
C70T20BS
C70Q20BS
C70Q24BS
C70QN20BS
C70QN24BS
2103830
2103840
2103842
2103850
2103852
63
63
63
63
63
3
4
4
5
5
508
508
610
508
610
1670
1670
1772
1670
1772
283
338
338
463
463
C80T20BS
C80Q20BS
C80Q24BS
C80QN20BS
C80QN24BS
2103860
2103870
2103872
2103880
2103882
72
72
72
72
72
3
4
4
5
5
508
508
610
508
610
1670
1670
1772
1670
1772
283
338
338
463
463
C90Q20BS
C90Q24BS
C90QN20BS
C90QN24BS
2103920
2103922
2103930
2103932
81
81
81
81
4
4
5
5
508
610
508
610
1670
1772
1670
1772
338
338
463
463
C100QN20BS
C100QN24BS
C100SX20BS
C100SX24BS
2103970
2103972
2103980
2103982
90
90
90
90
5
5
6
6
508
610
508
610
1670
1772
1670
1772
463
463
518
518
Sheave
Diam.
(mm)
457
508
610
406
457
A
1411
1443
1545
1357
1411
E
264
264
264
339
339
F
G
460
31.8
511
31.8
613
31.8
409
31.8
460
31.8
50 Tonnes
511
31.8
613
31.8
460
31.8
511
31.8
613
31.8
409
31.8
460
31.8
54 Tonnes
460
31.8
511
31.8
613
31.8
460
31.8
511
31.8
613
31.8
65 Tons
460
31.8
511
31.8
613
31.8
460
31.8
511
31.8
613
31.8
63 Tonnes
511
35.1
511
35.1
613
35.1
511
35.1
613
35.1
72 Tonnes
511
35.1
511
35.1
613
35.1
511
35.1
613
35.1
81 Tonnes
511
35.1
613
35.1
511
35.1
613
35.1
90 Tonnes
511
35.1
613
35.1
511
35.1
613
35.1
H
35.1
35.1
35.1
35.1
35.1
I
41.1
41.1
41.1
41.1
41.1
S
226
226
226
226
226
T
133
133
133
133
133
U
73.0
73.0
73.0
73.0
73.0
V
51.0
51.0
51.0
51.0
51.0
W
61.0
61.0
61.0
61.0
61.0
X
73.5
73.5
73.5
73.5
73.5
Weigh t
Each
(kg.)
341
392
489
354
422
35.1
35.1
35.1
35.1
35.1
35.1
35.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
226
226
226
226
226
226
226
143
143
133
133
133
133
133
73.0
73.0
73.0
73.0
73.0
73.0
73.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
61.0
61.0
61.0
61.0
61.0
61.0
61.0
84.0
84.0
73.5
73.5
73.5
73.5
73.5
336
419
341
392
489
354
422
35.1
35.1
35.1
35.1
35.1
35.1
41.1
41.1
41.1
41.1
41.1
41.1
226
226
226
226
226
226
133
133
133
133
133
133
73.0
73.0
73.0
73.0
73.0
73.0
51.0
51.0
51.0
51.0
51.0
51.0
61.0
61.0
61.0
61.0
61.0
61.0
73.5
73.5
73.5
73.5
73.5
73.5
341
392
489
422
490
585
35.1
35.1
35.1
35.1
35.1
35.1
41.1
41.1
41.1
41.1
41.1
41.1
226
226
226
226
226
226
133
133
133
133
133
133
73.0
73.0
73.0
73.0
73.0
73.0
51.0
51.0
51.0
51.0
51.0
51.0
61.0
61.0
61.0
61.0
61.0
61.0
73.5
73.5
73.5
73.5
73.5
73.5
341
392
489
422
490
585
38.1
38.1
38.1
38.1
38.1
46.2
46.2
46.2
46.2
46.2
302
302
302
302
302
184
184
184
184
184
91.9
91.9
91.9
91.9
91.9
68.8
68.8
68.8
68.8
68.8
79.2
79.2
79.2
79.2
79.2
83.8
73.7
73.7
83.8
83.8
531
560
708
721
907
38.1
38.1
38.1
38.1
38.1
46.2
46.2
46.2
46.2
46.2
302
302
302
302
302
184
184
184
184
184
91.9
91.9
91.9
91.9
91.9
68.8
68.8
68.8
68.8
68.8
79.2
79.2
79.2
79.2
79.2
83.8
73.7
73.7
83.8
83.8
531
560
708
721
907
38.1
38.1
38.1
38.1
46.2
46.2
46.2
46.2
302
302
302
302
184
184
184
184
91.9
91.9
91.9
91.9
68.8
68.8
68.8
68.8
79.2
79.2
79.2
79.2
73.7
73.7
83.8
83.8
617
780
721
934
38.1
38.1
38.1
38.1
46.2
46.2
46.2
46.2
302
302
302
302
184
184
184
184
91.9
91.9
91.9
91.9
68.8
68.8
68.8
68.8
79.2
79.2
79.2
79.2
83.8
83.8
73.7
73.7
721
934
755
977
r5S
F
r60S
F
r70S
F
r80S
F
r90S
F
r10S
F
270
All Rights Reserved
F
rom a 2 ton capacity snatch block to a 6,000 metric ton capacity crane block, McKissick®
can make a block to fit your lifting needs. In the lifting tackle industry, the name McKissick®
has stood for quality for almost 80 years.
McKissick’s major involvement in the block
business came after 1925. At that time, laws were
passed requiring safety guards on the wire line
entrance to oil field blocks. It was McKissick®
which developed and patented a wire line guard
which could be opened to allow the reeving of the
block without disassembly.
Through product diversification, and over 100
patents later, McKissick® manufactures blocks
and sheaves for many market uses including
construction, industrial, military, energy and marine
applications. From the many “Off the Shelf” items,
to the non-standard “Special Engineered” block
and tackle systems, McKissick® prides itself on
meeting your lifting needs.
McKissick®, a part of The Crosby Group, Inc. since 1959, is not only one
of the world’s largest producers of blocks, they also manufacture the
world’s largest block and tackle systems. Notable examples of custom
blocks manufactured by McKissick® include those used to set the
NASA space shuttle on the back of the 747 carrier jet.
The largest and most impressive example of McKissick’s capabilities
is the M-5000 block (6,000 metric ton capacity) for McDermott’s
DB-102 derrick barge.
McKissick’s latest accomplishment was receiving accreditation
for ISO 9001. That, in addition to being an API Q1 producer,
reinforces McKissick’s, as well as Crosby’s commitment to
continued quality.
McKissick® Products,
another reason to say “When buying Crosby,
you’re buying more than product, you’re buying Quality.”
www. the crosbygroup.com
crosbygroup@thecrosbygroup.com
McKissick® Overhaul Balls
UB500 SERIES TOP SWIVELING OVERHAUL BALLS
S320 or S320N
Eye Hook
S316A
SHUR-LOC®
Eye Hook
Both styles available with
optional McKissick® Wedge
Socket Assembly or
S-421T TERMINATORTM
Wedge Socket
UWO 422T
TERMINATORTM
Wedge Only
• The top swivel design on the UB500 assures the ball remains
• All hooks used on UB500 Overhaul Balls (S320, S320N &
stationary if the wire line spins.
• The swivel incorporates a sealed roller thrust bearing together with a grease fitting for easy lubrication.
• Each ball can be equipped with the new McKissick® US422
Wedge Socket which can be easily adjusted to
fit various sizes of wire rope by changing the wedge
(Ensure that correct wedge is used for selected wire
rope size).
• Design Factor 4:1
S316A) are forged from alloy steel. The S320 and S320N
hooks come complete with latches.
• Size 3.6 tonnes through 9 tonnes available
with Crosby’s
S316A “Positive Locking” SHUR-LOC® hook which may be
used for lifting personnel. Meets OSHA Rule 1926.550 (g).
• The S320 hook (PL latch) and the S320N hook (S4320 latch),
with the proper latch attached, may be used for personnel
lifting when secured with proper device (Bolt, nut and pin
for the PL latch; Cotter pin for the S4320 latch). Meets OSHA
Rule 1926.550 (g)
McKissick®
UB500
Model No.
Overhaul Ball Assembly
UB500
UB500
Working
“S”
“E”
Load
®
Eye Hook SHUR-LOC
Limit
Stock No.
t
Stock No.
Weight
Each
(kg)
Wire
Rope
Size
(mm)
Optional US-422T / US-422 Wedge Sockets
Wedge
Wedge
Weight
Socket
Only
Each
Assy.
Model
Stock No.
(kg)
Stock No.
No.
MB4T35
1036000*
1036005
3.6
26.3
10
US4
MB4T85
1036009*
1036018
3.6
46.3
11
US4
MB4T150
1036027*
1036032
3.6
73.5
13
US4
MB4T200
1036036*
1036041
3.6
91.2
13
US5
MB7T85
1036045*
1036050
6.3
49.4
14
US5
MB7T150
1036054*
1036063
6.3
77.1
16
US5
MB7T200
1036072*
1036077
6.3
95.3
16
US6
MB7T285
1036081*
1036086
6.3
146
19
US6
MB10T150
1036090*
1036095
9.0
98
MB10T200
1036099*
1036108
9.0
118
16
US6
MB10T285
1036117*
1036122
9.0
166
19
US6
MB10T350
1036126*
1036131
9.0
183
22
US8
MB10T650
1036135*
1036140
9.0
326
25
US8
MB12T150
1036144*
—
10.8
98
28
US10
MB12T200
1036153*
—
10.8
117
32
US10
MB12T285
1036171*
—
10.8
166
MB12T350
1036180*
—
10.8
183
MB12T650
1036189*
—
10.8
326
MB15T200
1036198*
—
13.5
135
MB15T350
1036207*
—
13.5
207
MB15T650
1036216*
—
13.5
342
MB15T1150
1036225*
—
13.5
595
16
US8A
MB20T200
1036234*
—
18.0
135
19
US8A
MB20T350
1036243*
—
18.0
207
22
US8
MB20T650
1036252*
—
18.0
342
25
US8
MB20T1150
1036261*
—
18.0
595
28
US10
MB25T350
1036270
—
22.5
242
32
US10
MB25T650
1036279
—
22.5
392
MB25T1150
1036288
—
22.5
645
MB30T650
1036297
—
27.0
392
MB30T1150
1036306
—
27.0
645
* Hook is New S-320 N Style. Replacement latch kit is S-4320. PL latch and S-4055 latch will not fit.
Weight
Each
(lbs.)
1044300†
1044309†
1044318†
1044327†
1044336†
1044345†
1044354†
1044363†
2.1
2.1
2.1
3.9
3.9
3.9
4.3
4.3
1047310†
1047301†
1047329†
1047338†
1047347†
1047356†
1047365†
1047374†
.27
.27
.27
.45
.45
.45
.64
.64
1044354†
1044363†
1044408†
1038607
1038616
1038625
4.3
4.3
9.4
9.4
21.1
21.1
1047365†
1047374†
1047422†
1046701
1046710
1046919
.64
.64
1.4
1.4
4.1
4.1
1038562
1038571
1044408†
1038607
1038616
1038625
7.9
7.9
9.4
9.4
21.1
21.1
1046656
1046665
1047422†
1046701
1046710
1046919
1.4
1.4
1.4
1.4
4.1
4.1
Standard Crosby S-5 Thrust style swivels can not be used with UB 500 Overhaul balls. For replacement swivels, contact Crosby customer service.
272
All Rights Reserved
s l l a B
l u a h r
e v O
®
k
c i s s i Kc M
8%7236:,9(/
29(5+$8/%$//6
UB-500E Top Swivel Overhaul Balls
with 320 Eye Hooks
A
510
533
558
568
589
624
632
657
799
808
832
846
884
799
808
832
846
909
955
986
1022
1072
955
986
1022
1072
1198
1248
1297
1248
1297
B
439
461
487
496
517
543
551
576
691
700
724
738
776
691
700
724
738
776
828
859
895
945
828
859
895
945
1021
1086
1135
1086
1135
C
191
235
286
318
235
286
318
353
286
318
353
381
456
286
318
353
381
456
318
381
456
549
318
381
456
549
381
456
549
456
549
D
34.5
34.5
34.5
34.5
40.9
40.9
40.9
40.9
53.0
53.0
53.0
53.0
53.0
53.0
53.0
53.0
53.0
53.0
76.5
76.5
76.5
76.5
76.5
76.5
76.5
76.5
76.0
76.0
76.0
76.0
76.0
Dimension s
(mm)
E
F
G
36.6
28.4
47.8
36.6
28.4
47.8
36.6
28.4
47.8
36.6
28.4
47.8
46.0
35.1
47.8
46.0
35.1
47.8
46.0
35.1
47.8
46.0
35.1
47.8
57.0
41.1
70.0
57.0
41.1
70.0
57.0
41.1
70.0
57.0
41.1
70.0
57.0
41.1
70.0
57.0
41.1
70.0
57.0
41.1
70.0
57.0
41.1
70.0
57.0
41.1
70.0
57.0
41.1
70.0
76.0
60.5
60.5
76.0
60.5
60.5
76.0
60.5
60.5
76.0
60.5
60.5
76.0
60.5
60.5
76.0
60.5
60.5
76.0
60.5
60.5
76.0
60.5
60.5
92.0
76.0
84.0
92.0
76.0
84.0
92.0
76.0
84.0
92.0
76.0
84.0
92.0
76.0
84.0
H
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
70.0
70.0
70.0
70.0
70.0
I
22.4
22.4
22.4
22.4
22.4
22.4
22.4
22.4
22.4
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
44.5
44.5
44.5
44.5
44.5
J
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
45.2
45.2
45.2
45.2
45.2
45.2
45.2
45.2
45.2
45.2
45.2
45.2
45.2
45.2
45.2
45.2
45.2
45.2
45.2
45.2
45.2
45.2
45.2
AA
63.5
63.5
63.5
63.5
76.0
76.0
76.0
76.0
102
102
102
102
102
102
102
102
102
102
127
127
127
127
127
127
127
127
165
165
165
165
165
McKissick®
Blocks
UB-500
"E"
Sto ck No .
1036000
1036009
1036027
1036036
1036045
1036054
1036072
1036081
1036090
1036099
1036117
1036126
1036135
1036144
1036153
1036171
1036180
1036189
1036198
1036207
1036216
1036225
1036234
1036243
1036252
1036261
1036270
1036279
1036288
1036297
1036306
50T
B
U
E
S
Model
No.*
MB4T35*
MB4T85*
MB4T150*
MB4T200*
MB7T85*
MB7T150*
MB7T200*
MB7T285*
MB10T150*
MB10T200*
MB10T285*
MB10T350*
MB10T650*
MB12T150*
MB12T200*
MB12T285*
MB12T350*
MB12T650*
MB15T200*
MB15T350*
MB15T650*
MB15T1150*
MB20T200*
MB20T350*
MB20T650*
MB20T1150*
MB25T350
MB25T650
MB25T1150
MB30T650
MB30T1150
* 4 ton thru 20 ton models use New 320-N Eye Hooks
s l
l a B
l u a h r e v O
®
k c i s
s i Kc M
UB-500S Top Swivel Overhaul Balls
with SHUR-LOC® Hooks
Dimension s
(mm)
50S
B
U
Mo del
No.
MB4T35
MB4T85
MB4T150
MB4T200
MB7T85
MB7T150
MB7T200
MB7T285
MB10T150
MB10T200
MB10T285
MB10T350
MB10T650
All Rights Reserved
UB-500
"S"
Stock No.
1036005
1036018
1036032
1036041
1036050
1036063
1036077
1036086
1036095
1036108
1036122
1036131
1036140
A
525
547
573
582
607
642
650
675
793
803
827
841
879
B
462
484
509
519
541
566
575
600
691
700
724
738
776
C
191
235
286
318
235
286
318
353
286
318
353
381
456
D
47.5
47.5
47.5
47.5
53.5
53.5
53.5
53.5
63.0
63.0
63.0
63.0
63.0
E
29.2
29.2
29.2
29.2
42.2
42.2
42.2
42.2
52.5
52.5
52.5
52.5
52.5
F
23.9
23.9
23.9
23.9
29.5
29.5
29.5
29.5
38.1
38.1
38.1
38.1
38.1
G
47.8
47.8
47.8
47.8
47.8
47.8
47.8
47.8
70.0
70.0
70.0
70.0
70.0
H
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
51.0
51.0
51.0
51.0
51.0
I
22.4
22.4
22.4
22.4
22.4
22.4
22.4
22.4
31.8
31.8
31.8
31.8
31.8
J
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
45.2
45.2
45.2
45.2
45.2
273
UB500 NON SWIVELING OVERHAUL BALLS
Key to McKissick® UB500
Utility Overhaul Ball Model Number
MB
4
McKissick® Working
Load Limit
Utility
(tons)
Overhaul
Ball
T
35
E
Swivel
Style
Ball only
Weight
Hook Style
T=Top
NS=Non
S320 or S320N
Eye Hook
E=320 or 320N
Eye Hook
S= SHUR-LOC®
Eye Hook
• Each ball can be equipped with the new McKissick®
MB4NS35
MB4NS85
MB4NS150
MB4NS200
MB7NS85
MB7NS150
MB7NS200
MB7NS285
MB10NS150
MB10NS200
MB10NS285
MB10NS350
MB10NS650
MB12NS150
MB12NS200
MB12NS285
MB12NS350
MB12NS650
MB15NS200
MB15NS350
MB15NS650
MB15NS1150
1036402*
1036411*
1036420*
1036429*
1036438*
1036447*
1036456*
1036465*
1036474*
1036483*
1036492*
1036501*
1036510*
1036519*
1036528*
1036537*
1036546*
1036555*
1036564*
1036573*
1036582*
1036591*
1036407
1036416
1036425
1036434
1036443
1036452
1036461
1036470
1036479
1036488
1036497
1036506
1036511
—
—
—
—
—
—
—
—
—
UWO 422T
TERMINATORTM
Wedge Only
available with Crosby’s
S316A “Positive Locking” SHUR-LOC® hook which may be
used for lifting personnel. Meets OSHA Rule 1926.550 (g).
• The S320 hook (PL latch) and the S320N hook (S4320 latch),
with the proper latch attached, may be used for personnel
lifting when secured with proper device (Bolt, nut and pin
for the PL latch; Cotter pin for the S4320 latch). Meets OSHA
Rule 1926.550 (g)
Overhaul Ball Assembly
UB500
UB500
“S”
“E”
Eye Hook SHUR-LOC®
Stock No.
Stock No.
Both styles available
with optional
McKissick® Wedge
Socket Assembly
• Size 3.6 tonnes through 9 tonnes
US422 Wedge Socket which can be easily adjusted to
fit various sizes of wire rope by changing the wedge
(Ensure that correct wedge is used for selected wire
rope size).
• All hooks used on UB500 Overhaul Balls (S320, S320N
& S316A) are forged from alloy steel. The S320 and S320N
hooks come complete with latches.
• Design Factor 4:1
McKissick®
UB500
Model No.
S316A
SHUR-LOC®
Eye Hook
Working
Load
Limit
t
Weight
Each
(kg)
3.6
3.6
3.6
3.6
6.3
6.3
6.3
6.3
9.0
9.0
9.0
9.0
9.0
10.8
10.8
10.8
10.8
10.8
13.5
13.5
13.5
13.5
24.5
44.5
71.5
90.7
47.2
74.8
92.9
143
89.8
110
157
175
318
89.8
109
157
175
318
121
193
327
581
Wire
Rope
Size
(mm)
Optional US-422T / US-422 Wedge Sockets
Wedge
Socket
Wedge
Weight
Assy.
Only
Each
Stock
Model
Stock No.
(kg)
No.
No.
Weight
Each
(kg)
9.6
11
13
13
14
16
16
19
US4
US4
US4
US5
US5
US5
US6
US6
1044300†
1044309†
1044318†
1044327†
1044336†
1044345†
1044354†
1044363†
2.1
2.1
2.1
3.9
3.9
3.9
4.3
4.3
1047310†
1047301†
1047329†
1047338†
1047347†
1047356†
1047365†
1047374†
0.27
0.27
0.27
0.45
0.45
0.45
0.64
0.64
16
19
22
25
28
32
US6
US6
US8
US8
US10
US10
1044354†
1044363†
1044408†
1038607
1038616
1038625
4.3
4.3
9.4
9.4
21.1
21.1
1047365†
1047374†
1047422†
1046701
1046710
1046919
0.64
0.64
1.4
1.4
4.1
4.1
16
19
22
25
28
32
US8A
US8A
US8
US8
US10
US10
1038562
1038571
1044408†
1038607
1038616
1038625
7.9
7.9
9.4
9.4
21.1
21.1
1046656
1046665
1047422†
1046701
1046710
1046979
1.4
1.4
1.4
1.4
4.1
4.1
* Hook is New S-320N style. Replacement latch kit is S-4320. PL latch and S-4055 latch will not fit.
† US-422T TERMINATORTM Style.
274
All Rights Reserved
s l l a B
l u a h r
e v O
®
k
c i s s i Kc M
8%
1216:,9(/
29(5+$8/%$//6
UB-500 Non Swiveling Overhaul Balls
with 320N Eye Hooks
Dimensions
(mm )
50N
B
U
E
S
A
510
533
558
568
589
624
632
657
799
808
832
846
884
799
808
832
846
909
955
986
1022
1072
B
439
461
487
496
517
543
551
576
691
700
724
738
776
691
700
724
738
776
828
859
895
945
s l
l a B
l u a h r e v O
C
191
235
286
318
235
286
318
353
286
318
353
381
456
286
318
353
381
456
318
381
456
549
®
k c i s
D
34.5
34.5
34.5
34.5
40.9
40.9
40.9
40.9
53.0
53.0
53.0
53.0
53.0
53.0
53.0
53.0
53.0
53.0
76.5
76.5
76.5
76.5
E
36.6
36.6
36.6
36.6
46.0
46.0
46.0
46.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
57.0
76.0
76.0
76.0
76.0
F
28.4
28.4
28.4
28.4
35.1
35.1
35.1
35.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
41.1
60.5
60.5
60.5
60.5
H
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
51.0
I
19.1
19.1
19.1
19.1
19.1
19.1
19.1
19.1
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
31.8
J
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
45.2
45.2
45.2
45.2
45.2
45.2
45.2
45.2
45.2
45.2
45.2
45.2
45.2
45.2
AA
63.5
63.5
63.5
63.5
76.0
76.0
76.0
76.0
102
102
102
102
102
102
102
102
102
102
127
127
127
127
s i Kc M
UB-500 Non Swiveling Overhaul Balls
with SHUR-LOC® Hooks
Dimensio ns
(mm)
UB
S
50N
Mod el
No.
MB4NS35
MB4NS85
MB4NS150
MB4NS200
MB7NS85
MB7NS150
MB7NS200
MB7NS285
MB10NS150
MB10NS200
MB10NS285
MB10NS350
MB10NS650
All Rights Reserved
UB-500NS
"S"
Stock No.
1036407
1036416
1036425
1036434
1036443
1036452
1036461
1036470
1036479
1036488
1036497
1036506
1036511
A
525
547
573
582
607
642
650
675
793
803
827
841
879
B
462
484
509
519
541
566
575
600
691
700
724
738
776
C
191
235
286
318
235
286
318
353
286
318
353
381
456
D
47.5
47.5
47.5
47.5
53.5
53.5
53.5
53.5
63.0
63.0
63.0
63.0
63.0
E
29.2
29.2
29.2
29.2
42.2
42.2
42.2
42.2
52.0
52.0
52.0
52.0
52.0
F
23.9
23.9
23.9
23.9
29.5
29.5
29.5
29.5
38.1
38.1
38.1
38.1
38.1
H
35.1
35.1
35.1
35.1
35.1
35.1
35.1
35.1
51.0
51.0
51.0
51.0
51.0
I
19.1
19.1
19.1
19.1
19.1
19.1
19.1
19.1
31.8
31.8
31.8
31.8
31.8
J
33.3
33.3
33.3
33.3
33.3
33.3
33.3
33.3
45.2
45.2
45.2
45.2
45.2
275
McKissick®
Blocks
Mod el
No.
MB4NS35
MB4NS85
MB4NS150
MB4NS200
MB7NS85
MB7NS150
MB7NS200
MB7NS285
MB10NS150
MB10NS200
MB10NS285
MB10NS350
MB10NS650
MB12NS150
MB12NS200
MB12NS285
MB12NS350
MB12NS650
MB15NS200
MB15NS350
MB15NS650
MB15NS1150
UB-500NS
"E"
Sto ck No .
1036402
1036411
1036420
1036429
1036438
1036447
1036456
1036465
1036474
1036483
1036492
1036501
1036510
1036519
1036528
1036537
1036546
1036555
1036564
1036573
1036582
1036591
McKissick®Overhaul Balls
s l l a B
l u a h r e v O® k c i s s i K c M
63/,7
29(5+$8/%$//6
Split Overhaul Ball
• Attaches easily to Wire Rope.
Wire Ro pe
Size
(mm )
10
13 - 16
16 - 19 - 22
HB
S
Catalog
No.
SHB - 20
SHB - 50
SHB - 100
$6
Stock
No.
2003830
2003831
2003832
Ball
Diam eter
A
(mm )
137
181
233
Weigh t
Each
(kg.)
9.07
22.7
45.4
• Designed with angular contact bearings which maximize efficiency, reliability and
service life of swivel and extend the life of the wire rope.
• Utilize genuine Crosby hooks which are forged alloy stell, Quenched and
Tempered and contain the patented QUIC-CHECK ® marking.
• Available with wide jaw opening that utilizes nylon spools and shields.
• Entire overhaul ball is zinc plated to resist corrosion.
• Designed for applications where headroom is critical.
• Other upper fittings available upon request.
s
l l a B
l u a h r e v O
®
k c i
s s i Kc M
Angular Contact Bearing Swivel Overhaul Balls
-15
S
A
AS-15
Sto ck
No .
2009806
2009807
2003969
2009808
Workin g Wire
Load
Rop e
Limit
Size
(t)*
(m m)
1.36
10
2.72
13
4.54
16
7.71
19
Dim en sions
(mm)
A
102
127
175
178
B
12.7
19.1
22.4
30.2
C
12.7
19.1
26.9
39.6
D
17.5
23.9
28.4
34.0
E
19.8
30.2
39.6
53.0
F
160
217
275
349
G
104
126
165
221
H
28.4
34.0
42.9
57.0
I
31.0
38.1
47.8
63.5
J
30.2
35.1
44.5
65.0
K
28.4
36.6
46.0
66.0
L
7.85
9.65
14.2
13.5
Weight
Each
(kg.)
4.08
8.62
19.5
27.2
276
All Rights Reserved
McKissick® Snatch Blocks
SEE APPLICATION AND
WARNING INFORMATION
On Pages 290-297
s k c o l B
h c t a
n S
®
k c
i s s i Kc M
61$7&+%/2&.6
New Improved Light Champion
Forged alloy heat treated hooks.
Forged steel swivel tees, yokes and shackles.
Hook and shackle assemblies on 114mm through 356mm sizes can be interchanged.
Can be furnished with bronze bushings or roller bearings.
Opening feature permits insertion of rope while block is suspended from gin-pole.
76mm thru 457mm 418 and 419 blocks have exclusive bolt retaining spring to assure no lost bolts.
Can be furnished with hook latch.
Pressure lube fittings.
Fatigue rated.
76mm - 254mm feature dual rated wireline sheaves.
418
Sh eave
Diameter
(mm)
* 76.0
** 76.0
**114
152
152
203
203
254
254
305
305
305
305
356
356
356
356
406
406
406
406
457
457
457
457
Bearing
C ode
BB
BB
BB
BB
RB
BB
RB
BB
RB
BB
RB
BB
RB
BB
RB
BB
RB
BB
RB
BB
RB
BB
RB
BB
RB
418
with
Ho ok
108038
108065
108127
108154
108225
108252
108323
108350
169169
199911
108421
108458
194920
199948
108528
108546
199975
200008
108608
108626
200099
200151
108644
108662
418
Stock No.
419
with
Shackle
109091
109037 †
109064
109126
109153
109224
109251
109322
109359
202961
169347
109420
109457
169356
167857
109527
109545
203041
203087
109607
109625
203130
203176
109643
109661
404
T ail
Bo ard
102016
102025
102098
102114
102169
102187
102230
102258
178890
178934
102301
102329
-
Wo rkin g
Wire R ope
L oad
Size
L imit
(m m)*
(t) †
8-10
2
8-10
2
10-13
4
16-19
8
16-19
8
16-19
8
16-19
8
16-19
8
16-19
8
16
8
16
8
19
8
19
8
16
8
16
8
19
8
19
8
19
15
19
15
22
15
22
15
22
15
22
15
26
15
26
15
Weigh t Each
(kg.)
418
419
404
with
with
Tail
Hook
Shackle
Board
2.26
2.04
1.81
1.22
5.31
5.44
2.99
12.2
12.6
6.80
12.2
12.6
6.80
15.0
15.4
9.53
15.0
15.4
9.53
18.6
19.1
13.2
18.6
19.1
13.2
21.8
22.2
16.3
21.8
22.2
16.3
21.8
22.2
16.3
21.8
22.2
16.3
24.9
25.4
24.9
25.4
24.9
25.4
24.9
25.4
59
61
59
61
59
61
59
61
68
70
68
70
68
70
68
70
-
Replacement
Sheave
Stock No.
460147
460147
2000232
460815
472688
461164
473277
461805
473776
462270
474141
462289
474150
463625
474766
463634
474775
4100056
4200028
4100065
4200037
464571
475792
4104640
6000000
* May be furnished in other wire rope sizes.
† Ultimate Load is 4 times the Working Load Limit.
** Available in Br onze Bushed only. 76 and 114 mm have self lubricating Bronze Bushing.
† Fitted with 1-1/4" (32mm) ID Swivel Eye.
‡ May be furnished in other r ope sizes.
NOTE: When order ing, please specify: size, block number, hook or shackle, bronze bushed or roller bearing,
and wire rope size.
All Rights Reserved
277
McKissick®
Blocks
•
•
•
•
•
•
•
•
•
•
SEE APPLICATION AND
WARNING INFORMATION
On Pages 290-297
s k c o l B
h c t a
n S
®
k
c i s s i Kc M
61$7&+%/2&.6
Champion
•
•
•
•
•
•
•
•
•
•
•
Hooks and side plates are forged alloy steel and heat treated.
Shackles and yokes are forged and heat treated steel.
Side plates are designed to eliminate possibility of rope jamming.
Can be furnished with bronze bushings or sealed roller bearings.
Opening feature permits insertion of rope while block is suspended from gin-pole.
Fatigue Rated.
Hook and shackle assemblies can be interchanged.
All parts are forged.
Blocks furnished with dual rated wireline sheaves.
420
Sheave
Diam.
(mm )
152
152
203
203
254
254
Bearin g
Cod e
BB
RB
BB
RB
BB
RB
420
with
Hoo k
169374
169392
169418
169445
110221
110258
Sto ck No .
421
with
Shackle
169481
204120
169515
204193
110720
110757
406
Tail
Board
167973
167982
167991
168008
103186
103202
Workin g
Wire Ro pe Lo ad LimSize
it
(m m) †
(t)*
19-22
12
19-22
12
19-22
15
19-22
15
19-22
15
19-22
15
Weight Each
(kg.)
420
421
406
with
with
Tail
Ho ok Shackle Board
18.1
21.8
10.9
18.1
21.8
10.9
23.1
25.9
13.6
23.1
25.9
13.6
28.6
31.3
19.1
28.6
31.3
19.1
Replacement
Sheave
Sto ck No .
460940
473035
461360
473534
462001
474025
† May be furnished in other Wire Rope sizes.
NOTE: When ordering, please specify: size, block number, hook or shackle, bronze bushed or roller bearing, and
wir e r ope size.
278
All Rights Reserved
SEE APPLICATION AND
WARNING INFORMATION
On Pages 290-297
s k c o l B
h c t a
n S
®
k c
i s s i Kc M
61$7&+%/2&.6
Super Champion
Drop forged, heat treated swivel hook or swivel shackle.
Hook and shackle assemblies on 203mm through 356mm sizes can be interchanged.
203mm thru 356mm 430 and 431 blocks have exclusive bolt retaining spring to assure no lost bolts.
Fatigue Rated.
203mm and 254mm models furnished with dual rated wireline sheaves.
430
Sheave
Diam .
(mm)
203
203
254
254
305
305
305
305
356
356
356
356
457
457
457
457
508
508
508
508
610
610
610
610
Bearing
Code
BB
RB
BB
RB
BB
RB
BB
RB
BB
RB
BB
RB
BB
RB
BB
RB
BB
RB
BB
RB
BB
RB
BB
RB
430
with
H ook
120023
120041
120096
120112
208536
208554
120176
120194
208572
208590
120256
120274
208689
208732
119482
119491
208750
208787
119507
119516
208812
208858
119525
119534
Sto ck No .
431
with
Shackle
121022
121040
121095
121111
169917
209303
121175
121193
209321
170424
121255
121273
209410
209465
119561
119570
209483
169864
119589
119598
209526
209553
119605
119614
407
Tail
Board
103523
103541
103603
103621
184375
184393
103685
103701
184419
184437
103765
103783
184552
184605
119641
119650
184623
184650
119669
119678
184687
184721
119687
119696
Wire
Ro pe
Size
(mm)
26-28
26-28
26-28
26-28
26
26
28
28
26
26
28
28
26
26
28
28
28
28
32
32
28
28
32
32
Working
Load
Limit
(t) *
20
20
20
20
20
20
20
20
20
20
20
20
25
25
25
25
30
30
30
30
30
30
30
30
Weig ht Each
(kg.)
430
431
407
with
with
Tail
Ho ok Sh ackle Board
34.0
39.5
19.1
34.0
39.5
19.1
40.4
45.8
24.9
40.4
45.8
24.9
46.7
52
31.8
46.7
52
31.8
46.7
52
31.8
46.7
52
31.8
56
61
40.8
56
61
40.8
56
61
40.8
56
61
40.8
109
118
75
109
118
75
109
118
75
109
118
75
170
181
98
170
181
98
170
181
98
170
181
98
204
215
132
204
215
132
204
215
132
204
215
132
Replacement
Sheave
Stock No.
461440
473614
462083
474105
462680
474524
462699
474533
463457
475024
463466
475033
4100298
4200331
4103348
4200322
4103936
4200769
4103945
4200778
4104114
4200983
4104123
4200992
† May be furnished in other Wire Rope sizes.
and wire rope size.
All Rights Reserved
279
McKissick®
Blocks
•
•
•
•
•
•
•
•
SEE APPLICATION AND
WARNING INFORMATION
On Pages 290-297
s k c o l B
h c t a
n S
®
k
c i s s i Kc M
61$7&+%/2&.6
Light Champion Double Sheave
•
•
•
•
•
•
•
•
Light champion snatch block as a double sheave block.
Drop forged swivel hook or swivel shackle.
Opening feature permits easy insertion of wire rope in both sheaves with removal of one bolt.
Fatigue Rated.
114mm - 254mm models furnished with dual rated wireline sheaves.
408
Sheave
Diam.
(mm)
† 114
152
152
203
203
254
254
305
305
305
305
356
356
356
356
Bearing
Co de
BB
BB
RB
BB
RB
BB
RB
BB
RB
BB
RB
BB
RB
BB
RB
Stock
408
with
Hook
104023
104103
104121
104185
104201
104265
104283
194578
168044
104345
104363
194621
194649
104425
104443
No.
409
with
Sh ackle
105022
105102
105120
105184
105200
105264
105282
195185
195229
105344
105362
195247
195265
105424
105442
Wire Rop e
Size
(mm) ‡
10-13
16-19
16-19
16-19
16-19
16-19
16-19
16
16
19
19
16
16
19
19
Working
Load L imit
(t) *
4
12
12
12
12
12
12
12
12
12
12
12
12
12
12
Weigh t Each
(kg.)
408
409
with
with
Ho ok
Shackle
8.16
8.16
20.4
22.7
20.4
22.7
24.0
26.3
24.0
26.3
31.8
34.0
31.8
34.0
40.8
43.1
40.8
43.1
40.8
43.1
40.8
43.1
45.4
47.6
45.4
47.6
45.4
47.6
45.4
47.6
Rep lacemen t
Sheave
Stock No.
2000232
460815
472688
461164
473277
461805
473776
462270
474141
462289
474150
463625
474766
463634
474775
† Available in Bronze Bushed only.
‡ May be furnished in other Wire Rope sizes.
NOTE: When ordering, please specify: size, block number , hook or shackle, bronze bushed or roller bearing, and
wir e r ope size.
280
All Rights Reserved
SEE APPLICATION AND
WARNING INFORMATION
On Pages 290-297
s k c o l B
h c t a
n S
®
k c
i s s i Kc M
$//2<61$7&+
%/2&.6
All Alloy Snatch Blocks
• Entire block made from heat treated alloy steel. Use of heat treated alloy gives block
only 60% of the weight of blocks of comparable capacities.
• Available with a bronze bushed or roller bearing sheaves.
• Easy opening feature of "Champion" blocks retained.
• Hook and shackle assemblies can be interchanged.
• Pressure lube fittings.
• Can be furnished with hook latch.
• Fatigue Rated.
• Blocks furnished with dual rated wireline sheaves.
416
Sheave
Diameter
(mm)
152
152
203
203
254
254
416
Alloy
Bearing
with
Code
H ook
BB
193427
RB
193472
BB
193490
RB
193542
BB
193613
RB
193677
Sto ck No .
417
Alloy
with
Shackle
168972
193757
168990
193819
193882
193935
402
Alloy
Tail
Board
179238
179283
179318
179363
179434
179498
Wire
Ro pe
Size
(mm) †
19-22
19-22
19-22
19-22
19-22
19-22
Working
Load
Limit
(t) *
12
12
12
12
12
12
Weig ht Each
(kg.)
416
417
402
Allo y
Alloy
Alloy
with
with
Tail
Ho ok Sh ackle Board
11.8
12.20
6.80
11.8
12.20
6.80
15.0
15.40
9.50
15.0
15.40
9.50
18.6
19.10
13.20
18.6
19.10
13.20
Replacement
Sheave
Stock No.
460824
472679
461173
473286
461814
473785
† May be furnished in other wir e r ope sizes.
McKissick®
Blocks
and wire rope size.
All Rights Reserved
281
Lebus® Snatch Blocks
SEE APPLICATION AND
WARNING INFORMATION
On Pages 290-297
s k c
o l B
h c t a
n S
®
s u b e L
L-160 Series
Heavy Duty Snatch Blocks
•
•
•
•
•
•
•
•
Hook is Forged Alloy Steel — Quenched and Tempered.
Designed for fast, efficient line changes.
Beaded side plate prevents rope from jamming.
Available with hook, shackle or tailboard (pin only).
Fatigue Rated.
Block
No.
L-5-H
L-5-H
L-5-S
L-5-S
L-5-T
L-5-T
L-6-H
L-6-H
L-6-S
L-6-S
L-6-T
L-6-T
Bearing
Code
BB
RB
BB
RB
BB
RB
BB
RB
BB
RB
BB
RB
L-160
Stock
N o.
599506
599515
599524
599533
599542
599551
599560
599579
599588
599597
599604
599613
Fitting
Hook
Hook
Shackle
Shackle
Tailboard
Tailboard
Hook
Hook
Shackle
Shackle
Tailboard
Tailboard
Sheave
Diam.
(mm )
127
127
127
127
127
127
149
149
149
149
149
149
Wo rkin g
L oad
L imit
(t)*
6
6
6
6
6
6
12
12
12
12
12
12
Wire
Rop e
Size
(mm)
10-13
10-13
10-13
10-13
10-13
10-13
16-19
16-19
16-19
16-19
16-19
16-19
Weigh t
Each
(kg.)
6.94
6.94
6.80
6.80
4.54
4.54
14.4
14.4
13.6
13.6
8.07
8.07
Replacement
Sheave
Sto ck No .
592095
592157
592095
592157
592095
592157
592175
592255
592175
592255
592175
592255
282
All Rights Reserved
Lebus ® Snatch Blocks
SEE APPLICATION AND
WARNING INFORMATION
Pa ra Esp añ o l: ww w .th ec ros by gro u p.co m
s k c
o l B
h c t a
n S
®
On Pages 290-297
s u b e L
L-170 Series
General Purpose Snatch Blocks
•
•
•
•
•
•
•
Hook is Forged Alloy Steel — Quenched and Tempered.
Opened and closed in seconds without the use of tools.
Available with hook, shackle or tailboard (pin only).
Either wire or manila rope may be used.
Can be furnished with an hook latch.
Blo ck
No.
L-45-H
L-45-H
L-45-S
L-45-S
L-45-T
L-45-T
Bearing
Cod e
BB
RB
BB
RB
BB
RB
L-170
Stock
No.
599800
599819
599828
599837
599846
599855
F itting
Hook
Hook
Shackle
Shackle
Tail Board
Tail Board
Sheave
Diam.
(mm )
105
105
105
105
105
105
Working
Lo ad
Lim it
(t) *
4.5
4.5
4.5
4.5
4.5
4.5
Wire
Rope
Size
(mm )
10-13
10-13
10-13
10-13
10-13
10-13
Manila
Rope
Size
(mm )
32
32
32
32
32
32
Weigh t
Each
(kg.)
5.90
5.90
5.90
5.90
4.08
4.08
Replacement
Sheave
Sto ck No .
460405
472580
460405
472580
460405
472580
McKissick®
Blocks
NOTE: When Or dering, specify either roller bearing or bronze bushed sheaves.
All Rights Reserved
283
Crosby® Snatch Blocks
SEE APPLICATION AND
WARNING INFORMATION
On Pages 290-297
s k
c o l B
h c t a
n S
®
y b s o r C
&
61$7&+%/2&.6
General Purpose Snatch Blocks
•
•
•
•
•
Unique locking device permits disengagement by simply folding hook.
Formed steel side plates with capacity stamped permanently in place.
Self-Lubricating bronze bushings.
Can be furnished with an hook latch.
Furnished with dual rated wireline sheaves.
Sheave
Diam .
(mm)
152
203
Block
No.
10611
10811
Working
Load L imit
(t)*
2
3
C-700
Stock No.
260014
261013
Wire Rope
Size
(mm)
10-13
13-16
Weight Each
(kg.)
5.44
8.44
Fitting
Swivel Hook
Swivel Hook
Wire Rope
Size
(mm)
19-22
Weight Each
(kg.)
12.7
Fitting
Swivel Hook
Wire Rope
Size
(mm)
19-22
Weight Each
(kg.)
9.53
Fitting
Tailboard
s k c o
l B
h c t a n S
®
y b
s o r C
&
61$7&+%/2&.6
Heavy Duty Utility Snatch Block
•
•
•
•
•
•
Forged steel sheaves, bronze bushings.
Pressure lube fitting.
Drop forged steel hook.
Self-locking style. Locks with hook load.
Furnished with dual rated wireline sheave.
Sheave
Diam .
(mm)
152
Block
No.
60611
Working
Load L imit
(t)*
6.35
C-720
Stock No.
280010
* Ultimate Load is 3.5 times the Working Load Limit.
s k c o
l B
h c t a n S
®
y b
s o r C
&
72**/(%/2&.
Toggle Block (Tail Board)
• Forged steel sheaves, bronze bushings.
• Pressure lube fitting.
• Furnished with dual rated wireline sheave.
Sheave
Diam .
(mm)
152
Block
No.
70610
C-720 TB
Stock No.
290018
Working
Load L imit
(t)*
6.35
* Ultimate Load is 3.5 times the Working Load Limit.
284
All Rights Reserved
McKissick® Special Application Blocks
SEE APPLICATION AND
WARNING INFORMATION
On Pages 290-297
s k c o l B
n o i t a c
i l p p A
l a
i c e p S
®
k c i s
s i Kc M
Hay mFork Pulleys with Swivel Hook or Swivel Eye
•
•
•
•
•
•
•
One piece pressed steel shells.
Edges well rounded to prevent chaffing of rope.
Forged steel eyes and hooks.
Furnished with roller bearings.
Available Painted or Zinc Plated.
Sheave
Diameter
(m m)
114
114
114
114
203
152
152
152
152
Block
No.
HF-1
HF-2
HF-3
HF-4
HF-5
HF-11
HF-12
HF-13
HF-14
Hay F ork Pulleys
Stock No.
Pain ted
Z inc Plated
170022
170594
170086
170629
170148
170656
170200
170683
170264
170380
170442
170503
170567
-
Working
Load L im it
(t) *
.91
.91
.91
.91
1.81
1.81
1.81
1.81
1.81
Standard
Ro pe Size
(mm)
32 MR
32 MR
13 WR
13 WR
13 WR
38 MR
38 MR
16 WR
16 WR
End
Fitting
Swivel Hook
Swivel Eye
Swivel Hook
Swivel Eye
Swivel Eye
Swivel Hook
Swivel Eye
Swivel Hook
Swivel Eye
Weigh t
Each
(kg.)
4.99
5.44
13.6
15.9
C onnectio n
Swivel Eye
Swivel Eye
Swivel Eye
Swivel Eye
Weight
Each
(kg.)
2.72
2.72
2.72
2.72
4.99
4.99
4.99
4.99
4.99
Rope Code: MR - Manila Rope, WL - Wire Line.
Tong Blocks
Sheave
Diameter
(m m)
152
203
254
305
Block
No.
TB-1
TB-1
TB-1
TB-1
171
Stock No.
171012
171058
171101
171156
Working
Load L imit
(t)*
.45
.91
2.27
2.27
Wire Rop e
Size
(mm )
19
19
19
19
McKissick®
Blocks
• Steel sheaves with roller bearings and pressure lubrication.
• Forged steel eyes and hooks.
• Easy opening feature shown available in 8" (203mm) size only.
Lay Down Blocks
• Used to lay down drill pipe.
• All steel construction, steel sheaves mounted on antifriction bearings, grooved for
maximum of 19mm wire line.
• Hook made to fit into end of drill pipe, handy dead end becket for
returning block — hooks have handle for disengagement.
Sh eave
Diameter
(mm)
114
152
All Rights Reserved
Block
No.
443
443
443
Sto ck No .
171414
171432
Workin g
L oad Limit
(t)
.23
.45
Wire Rope
Size
(mm)
13
19
Weig ht
Each
(kg .)
5.44
7.71
Typ e
Block
Regular
Regular
285
McKissick® Oilfield Servicing Blocks
SEE APPLICATION AND
WARNING INFORMATION
On Pages 290-297
s k
c o l B
g n i c i v r
e S
d l e i f l i O
®
k c i
s s i Kc M
0
M-491 Derrick Hoist Blocks
New design provides the dependability of standard McKissick ® snatch
blocks, along with features that make it perfect for the tugger application.
• All blocks 14" and larger are furnished with McKissick® Roll Forged™sheaves
with flame hardened grooves.
• 8" and 10" blocks furnished with dual rated wireline sheaves.
• Sealed tapered roller bearings extend the life of the center pin and bearings,
and allows for faster line speeds than recommended with standard snatch blocks.
• Suitable for hoisting personnel, contingent upon all employees, including the winch operator,
being trained to follow any applicable Federal, local and industry standards.
• Shackle fitting swivels for easy positioning.
• Forged steel swivels, tees, yokes and shackles are Quenched & Tempered.
• Sheave lubrication through center pin for easy maintenance.
• A wide variety of configurations:
• 4, 8, 12 or 15 metric ton capacity
• 3/8", 7/16", 1/2", 9/16", 5/8", 7/8" and 1" wire line sizes
• Painted or Galvanized finish
• Design factor of 4 to 1
• Manufactured by an API Q1 Certified facility
286
Working
Load
Limit
(t)
Sheave
Diam eter
(mm )
Wire Ro pe
Size
(m m)
M-491
Stock No.
Painted
M-491
Stock No.
Galvanized
Weight
Each
(kg.)
4
8
8
12
12
12
15
15
203
254
254
254
356
356
406
406
10 - 13
10 - 13
13 - 14
13 - 14
16
19
22
25
2020161
2020806
2020824
2021118
2021136
2021154
2021172
2021190
2020170
2020815
2020833
2021127
2021145
2021163
2021181
2021199
16
25
25
25
43
43
68
48
All Rights Reserved
SEE APPLICATION AND
WARNING INFORMATION
On Pages 290-297
s k c o l B
g n i c i
v r e S
d l e i f l
i O
®
k
c i s s i Kc M
6(5,(6%/2&.6
$OVRDYDLODEOHZLWK
Rod Hook Clevis
McKissick ® Oilfield Tubing Blocks
• Exclusive E-Z opening guards, no bolts to pull out and lose. Feature gives fastest possible
exposure of sheave cluster for quick reeving.
• Extremely short overall length, extra weight, excellent balance for fast non-wobbling falls.
• Extra large sealed sheave bearing diameters for fully rated capacities.
• Tapered roller thrust bearing in hook.
• Duplex hook for easy elevator operation, locks in eight positions.
• Convenient rod hook clevis available.
• Completely streamlined, no projections.
• McKissick® Roll-Forged ™, flame hardened sheaves, grooved for proper wire line size. Contact
Crosby for available wire line sizes.
• Threaded hook parts precision machined and individually fitted for maximum performance.
• All blocks available with additional cheek weights.
70 Series Tub ing Blocks
Working
Load Limit
(t)
67.5
67.5
90
90
135
135
135
135
72A
Stock
No.
111792
111890
111818
111916
111827
111925
128793
125545
Block
Con fig.*
20" 73
20" 73-A
24" 73
24" 73-A
30" 73
30" 73-A
30" 74
30" 74-A
Wire L ine
Size
(mm)
22
22
25
25
28
28
28
28
Weig ht
Each
(kg .)
803
823
1195
1247
2018
1845
1996
2024
* S pring loaded duplex hook assur ing ample travel for efficient tubing oper ations. No load carrying thr eads.
s k c o
l B
g n i c i v r e S
d l e i f l i O
®
k c i s
s i Kc M
80
Stock
No.
112130
112238
112149
112247
112158
112256
112167
112265
112176
112274
117475
117484
112185
112283
117493
117509
All Rights Reserved
Blo ck
Config.
17" 83
17" 83-A
20" 82
20" 82-A
20" 83
20" 83-A
24" 82
24" 82-A
24" 83
24" 83-A
24" 84
24" 84-A
30" 83
30" 83-A
30" 84
30" 84-A
80 Series T ubing Blocks
Working
L oad Lim it
(t)
45
45
45
45
67.5
67.5
67.5
67.5
90
90
90
90
135
135
135
135
Wire Line
Size
(mm )
22
22
22
22
22
22
25
25
25
25
25
25
28
28
28
28
McKissick®
Blocks
6(5,(6%/2&.6
Weight
Each
(kg)
491
503
510
564
727
753
816
830
998
991
1225
1247
1225
1617
1746
1873
287
SEE APPLICATION AND
WARNING INFORMATION
On Pages 290-297
s k c o l B
g n i c
i v r e S
d l e i f
l i O
®
k
c i s s i Kc M
:(///2**(5
6
%/2&.6
Floor Blocks & Top Blocks
•
•
•
•
•
Conductor cable ONLY is recommended for use with Well Logger's Blocks.
For use in high speed well logging, perforating, etc.
Extra large double row, pre-adjusted sealed tapered bearing.
Quick opening pin for fast string-up, light weight for easy handling.
Alloy aluminum housing for maximum strength and minimum weight.
FLOOR BLOCKS
f lor
Sh eave
Diameter
(mm)
178
254
254
305
356
356
508
610
Block
No.
475
473
475
475
475
477
477
477
Flo or Block
Stock No .
180020
180128
180253
180440
180618
169784
191072
191107
Working
Load Limit
(t)*
1.35
1.35
2.25
2.25
3.30
5.4
5.4
9.0
Con ducto r
Cable Size
(mm)
5
5
8
8
8
6
6
8
Weight
Each
(kg)
4.5
5.0
9.5
10.8
19.5
26.3
31.8
58.9
Con nection
Swivel Hanger
Swivel Hanger
Swivel Hanger
Swivel Hanger
Swivel Hanger
Swivel Clevis
Swivel Clevis
Swivel Clevis
Con ducto r
Cable Size
(mm)
8
5
8
8
8
Weight
Each
(kg)
4.5
4.5
9.5
10.8
19.5
Con nection
Stinger Pin
Stinger Pin
Stinger Pin
Stinger Pin
Stinger Pin
TOP BLOCKS
top
Sh eave
Diameter
(mm)
178
254
254
305
356
Block
No.
476
474
476
476
476
T op Block
Stock No .
180075
180173
180333
180529
180707
Working
Load Limit
(t)*
2.25
2.25
3.6
3.6
3.6
288
All Rights Reserved
SEE APPLICATION AND
WARNING INFORMATION
On Pages 290-297
s k c o l B
g n i c i
v r e S
d l e i f l
i O
®
k
c i s s i Kc M
&52:1%/2&.6
Crown Blocks
•
•
•
•
•
•
McKissick® Roll-Forged ™ sheaves with flame hardened grooves.
Double row pre-adjusted sealed tapered bearings mounted on a steel shaft.
Heavy center and side plates for proper support of center pin.
Pre-assembled units for rapid attachment to crown assembly for installation on derrick.
On multiple sheave assemblies, one sheave can be grooved for sand line on request.
Other sizes available upon request.
Sh eave
Diameter
(mm)
610
610
610
610
610
610
610
762
762
762
762
762
Block
No.
241
242
243
731
732
733
734
741
742
743
744
745
Crown Block
Stock
No.
351158
351167
351176
351185
351194
351201
351210
351229
351238
351247
351256
351265
No. of
Sh eaves
1
2
3
1
2
3
4
1
2
3
4
5
Working
Load Lim it
(t)
13.5
27
40.5
31.5
67.5
90
113
36
72
99
126
153
Stand ard
Wire Ro pe
Size
(mm )*
22
22
22
25
25
25
25
28
28
28
28
28
Weig ht
Each
(kg )
91
126
170
91
159
238
327
147
254
363
445
528
McKissick®
Blocks
* May be furnished in other wire rope sizes.
All Rights Reserved
289
Tackle Block and Sheave Assembly
Warning, Use &
Maintenance Information
•
•
•
•
•
•
•
•
•
•
WARNING
A potential hazard exists when lifting or dragging
heavy loads with tackle block assemblies.
Failure to design and use tackle block systems
properly may cause a load to slip or fall – the result
could be serious injury or death.
Failure to design lifting system with appropriate
sheave assembly material for the intended application may cause premature sheave, bearing or
wire rope wear and ultimate failure - the result
could be serious injury or death.
A tackle block system should be rigged by a
qualified person as defined by ANSI/ASME B.30.
Instruct workers to keep hands and body away
from block sheaves and swivels – and away from
“pinch points” where rope touches block parts or
loads.
Do not side load tackle blocks.
See OSHA Rule 1926.550(g) for personnel hoisting
by cranes and derricks, and OSHA Directive CPL
2-1.29 — Interim Inspection Procedures During
Communication Tower Construction Activities.
Only a Crosby or McKissick Hook with a PL latch
attached and secured with a bolt, nut and cotter
pin (or toggle pin) or a PL-N latch attached and
secured with toggle pin; or a Crosby hook with an
S-4320 latch attached and secured with cotter pin
or bolt, nut and pin; or a Crosby SHUR-LOC® Hook
in the locked position may be used for any personnel hoisting. A hook with a Crosby SS-4055 latch
attached shall NOT be used for personnel lifting.
Instruct workers to be alert and to wear proper
safety gear in areas where loads are moved or
supported with tackle block systems.
Use only genuine Crosby parts as replacement.
Read, understand, and follow these instructions to select, use and maintain tackle block
systems.
Important:
General Cautions or Warnings
Ratings shown in Crosby Group literature are applicable
only to new or “in as new” products.
Working Load Limit ratings indicate the greatest force or
load a product can carry under usual environmental
conditions. Shock loading and extraordinary conditions
must be taken into account when selecting products for use
in tackle block systems. Working Load Limit ratings are
based on all sheaves of tackle block system being utilized.
If all sheaves are not utilized, balance must be maintained,
and the Working Load Limit must be reduced proportionally
to prevent overloading sheave components. Changes from
full sheave reeving arrangement should be only at the
recommendation of a qualified person, and incorporate
good rigging practices.
In general, the products displayed in Crosby Group
literature are used as parts of a system being employed to
accomplish a task. Therefore, we can only recommend
within the Working Load Limits, or other stated limitations,
the use of products for this purpose.
The Working Load Limit or Design (Safety) Factor of each
Crosby product may be affected by wear, misuse,
overloading, corrosion, deformation, intentional alteration,
and other use conditions. Regular inspection must be
conducted to determine whether use can be continued at
the catalog assigned WLL, a reduced WLL, a reduced
Design (Safety) Factor, or withdrawn from service.
Crosby Group products generally are intended for tension
or pull. Side loading must be avoided, as it exerts additional
force or loading which the product is not designed to
accommodate.
Always make sure the hook supports the load. The latch
must never support the load.
Welding of load supporting parts or products can be
hazardous. Knowledge of materials, heat treatment, and
welding procedures are necessary for proper welding.
Crosby Group should be consulted for information.
Definitions
STATIC LOAD – The load resulting from a constantly
applied force or load.
WORKING LOAD LIMIT – The maximum mass or force
For maximum safety and efficiency, tackle block and sheave
systems must be properly designed, used, and maintained.
You must understand the use of tackle block components
and sheaves in the system. These instructions provide this
knowledge. Read them carefully and completely.
Some parts of these instructions must use technical words
and detailed explanations. NOTE: If you do not understand
all words, diagrams, and definitions — DO NOT TRY TO
DESIGN OR USE A TACKLE BLOCK OR SHEAVE
SYSTEM! For further assistance, call:
In U.S.A. - Crosby Engineered Products Group at
800-777-1555.
In CANADA - Crosby Canada, Ltd. (905) 451-9261.
IN EUROPE - N.V. Crosby Europe 32-15-757125.
As you read instructions, pay particular attention to safety
information in bold print.
KEEP INSTRUCTIONS FOR FUTURE USE – DO NOT
THROW AWAY!
290
which the product is authorized to support in general service
when the pull is applied in-line, unless noted otherwise, with
respect to the center line of the product. This term is used
interchangeably with the following terms.
1. WLL
2. Rated Load Value
3. SWL
4. Safe Working Load
5. Resultant Safe Working Load
WORKING LOAD – The maximum mass or force which
the product is authorized to support in a particular service.
PROOF LOAD – The average force applied in the
performance of a proof test; the average force to which a
product may be subjected before deformation occurs.
PROOF TEST – A test applied to a product solely to
determine non conforming material or manufacturing
defects.
Copyright© 2002 The Crosby Group, Inc.
All Rights Reserved
the product fails, or no longer supports the load.
SHOCK LOAD – A force that results from the rapid
application of a force (such as impacting and/or jerking) or
rapid movement of a static load. A shock load significantly
adds to the static load.
DESIGN (SAFETY) FACTOR – An industry term denoting
a product’s theoretical reserve capability; usually computed
by dividing the catalog Ultimate Load by the Working Load
Limit. Generally expressed for blocks as a ratio of 4 to 1.
TACKLE BLOCK – An assembly consisting of a
sheave(s), side plates, and generally an end fitting (hook,
shackle, etc.) that is used for lifting, lowering, or applying
tension.
SHEAVE / SHEAVE BEARING ASSEMBLY - Purchased
by O.E.M. or end user to be used in their block or lifting
system design.
Fitting Maintenance
Fittings, including hooks, overhaul balls, shackles, links,
etc., may become worn and disfigured with use, corrosion,
and abuse resulting in nicks, gouges, worn threads and
bearings, sharp corners which may produce additional
stress conditions and reduce system load capacity.
Grinding is the recommended procedure to restore smooth
surfaces. The maximum allowance for reduction of a
product’s original dimension due to wear or repair before
removal from service is:
1. Any single direction - No more than 10% of original
dimension;
2. Two directions - No more than 5% of each
dimension.
For detailed instructions on specific products, see the
application and warning information for that product. Any
greater reduction may necessitate a reduced Working Load
Limit.
Any crack or deformation in a fitting is sufficient cause to
withdraw the product from service.
Selection Guide
Some of the blocks shown in Crosby Group literature are
named for their intended use and selection is routine. A
few examples include the “Double Rig Trawl Block” used in
the fishing industry, the “Well Loggers Block” used in the oil
drilling industry, and the “Cargo Hoisting Block” used in the
freighter boat industry and “Derrick and Tower Block” used
for hoisting personnel. Others are more generally classified
and have a variety of uses. They include snatch blocks,
regular wood blocks, standard steel blocks, etc. For
example, snatch blocks allow the line to be attached by
opening up the block instead of threading the line through
the block. This feature eliminates the use of rope guards
and allows various line entrance and exit angles to change
direction of the load. These angles determine the load on
the block and/or the block fitting. (See “Loads on Blocks.”
on page 293.) Snatch blocks are intended for infrequent
and intermittent use with slow line speeds.
A tackle block sheave assembly is one element of a system
used to lift, change direction or drag a load. There are other
elements in the system including the prime mover (hoist,
All Rights Reserved
winch, hand), supporting structure, power available, etc. All
of these elements can influence the type of tackle block or
sheave required. When selecting a block or sheave for the
system in your specific application, you should consider the
other elements as well as the features of the blocks and
sheaves shown in Crosby Group literature.
To select a tackle block or sheave to fit your requirements,
consider the following points:
1. Are there regulations which could affect your choice
of blocks or sheaves, such as federal or state OSHA,
elevator safety, mine safety, maritime, insurance, etc.?
2. What is the weight of the load, including any
dynamics of impacts that add to load value? You must
know this to determine the minimum required Working
Load Limit value of the block or load on sheave.
3. How many parts of line are required? This can be
determined given the load to be lifted and the line pull
you have available. As an alternative, you could calculate the line pull required with a given number of parts of
line and a given load weight. (See “How to Figure Line
Parts,” page 296).
4. What is the size of line to be used? Multiply the
available line pull by the desired safety factor for wire
rope to determine the minimum catalog wire rope breaking strength; consult a wire rope catalog for the corresponding grade and diameter of wire rope to match. You
should also consider fatigue factors that affect wire rope
life. (See “Sheave Size & Wire Rope Strength” page
295).
5. What is the speed of the line? This will help you
determine the type of sheave bearing necessary. There
are several choices of bearings suitable for different
applications, including:
Common (Plain) Bore for very slow line speeds and
very infrequent use (high bearing friction).
Self Lubricating Bronze Bushings for slow line
speeds and infrequent use (moderate bearing friction).
Bronze Bushing with pressure lubrication for slow line
speeds and more frequent use at greater loads (moderate bearing friction).
Anti-friction Bearings for faster line speeds and more
frequent use at greater loads (minimum bearing friction).
6. What type of fitting is required for your application?
The selection may depend on whether the block will be
traveling or stationary. Your choices include single or
multiple hooks with or without throat latches and shackles, which are the most secured load attachment. You
should also decide whether the fitting should be fixed,
swivel or swivel with lock. If it is a swivel fitting, then
selection of a thrust bearing may be necessary. There
are plain fittings with no bearings for positioning at no
load, bronze bushed fittings for infrequent and moderate
load swiveling, and anti-friction bearing equipped fittings
for frequent load swiveling.
7. How will the block be reeved and does it require a dead
end becket? (See “The Reeving of Tackle Blocks”, page
294).
8. If the block is to be a traveling block, what weight is
required to overhaul the line? (See “How to Determine
Overhaul Weights”, page 296).
9. What is the fleet angle of the wire line? Line entrance
and exit angles should be no more than 1-1/2 degree.
10. How will the block or sheave be maintained? Do
conditions in your application require special maintenance considerations? (See “Tackle Block and Sheave
Maintenance,” page 292 and “Fitting Maintenance,"
page this page).
291
McKissick
Blocks
ULTIMATE LOAD – The average load or force at which
11. Reference current edition of “Wire Rope Users Manual” for additional sheave design and maintenance information.
Tackle Block and Sheave Maintenance
Tackle Blocks and Sheaves must be regularly inspected,
lubricated, and maintained for peak efficiency and extended
usefulness. Their proper use and maintenance is equal in
importance to other mechanical equipment. The frequency
of inspection and lubrication is dependent upon frequency
and periods of use, environmental conditions, and the user’s
good judgment.
Inspection: As a minimum, the following points should be
considered:
1. Wear on pins or axles, rope grooves, side plates,
bushing or bearings, and fittings (See Fitting Maintenance). Excessive wear may be a cause to replace parts
or remove block or sheave from service.
2. Deformation in side plates, pins and axles, fitting
attachment points, trunnions, etc. Deformation can be
caused by abusive service and / or overload and may be
a cause to remove block or sheave from service.
3. Misalignment or wobble in sheaves.
4. Security of nuts, bolts, and other locking methods,
especially after reassembly following a tear down
inspection. Original securing method should be used;
e.g., staking, set screw, cotter pin, cap screw.
5. Pins retained by snap rings should be checked for
missing or loose rings.
6. Sheave pin nuts should be checked for proper positioning. Pins for tapered roller bearings should be tightened to remove all end play during sheave rotation. Pins
for bronze bushings and straight roller bearings should
have a running clearance of .031 inch per sheave of end
play and should be adjusted accordingly.
7. Hook or shackle to swivel case clearance is set at
.031 to .062 at the factory. Increased clearance can
result from component wear. Clearance exceeding .12
to .18 should necessitate disassembly and further
inspection.
8. Deformation or corrosion of hook and nut threads.
9. Surface condition and deformation of hook (See Fitting Maintenance and ANSI B30.10.)
10. Welded side plates for weld corrosion or weld cracking.
11. Hook latch for deformation, proper fit and operation.
12. Remove from service any bushings with cracks on
inside diameter or bushing end. Bushings that are
cracked and/or extended beyond sheave hub are indications of bushing overload.
Lubrication: The frequency of lubrication depends upon
frequency and period of product use as well as
environmental conditions, which are contingent upon the
user’s good judgment.
Assuming normal product use, the following schedule is
suggested when using lithium-base grease of a medium
consistency.
Bronze Bushings — (Not Self Lubricated) — Every 8
hours of continuous operation or every 14 days of intermittent operation.
Self Lubricating Bronze Bushing — are for slow line
speeds and infrequent use (moderate bearing friction).
Frequent inspection is required to determine the condition of bushing.
Hook Bearings
Anti Friction — Every 14 days for frequent swiveling;
every 45 days for infrequent swiveling.
Bronze Thrust Bushing or No Bearing — Every 16
hours for frequent swiveling; every 21 days for infrequent swiveling.
Tackle Block Maintenance also depends upon proper block
selection (see “Loads on Blocks”), proper reeving (see “The
Reeving of Tackle Blocks”), consideration of shock loads,
side loading, and other adverse conditions.
Sheave Bearing Application
Information
Sheaves in a system of blocks rotate at different rates of
speed, and have different loads. When raising and lowering,
the line tension is not equal throughout the system. Refer
to Page 296 “How to Figure Line Parts” for assistance in
determining lead line loads used for bushing or bearing
selection.
BRONZE BUSHINGS—
Bronze Bushings are used primarily for sheave applications
using slow line speed, moderate load, and moderate use.
The performance capability of a bearing is related to the
bearing pressure and the bearing surface velocity by a
relationship known as true PV (Maximum Pressure Velocity Factor). The material properties of the Bronze
Bushings furnished as standard in Crosby catalog sheaves
are:
(BP) Maximum Bearing Pressure :4500 PSI
(BV) Maximum Velocity at Bearing :1200 FPM
(PV) Maximum Pressure Velocity Factor: 55000
(It should be noted that due to material property relations,
the maximum BP times the maximum BV is NOT equal to
the maximum PV.)
Formula for Calculating Bearing Pressure:
BP =
292
Shaft Size x Hub Width
Note: Angle Factor Multipliers listed on this page 293.
Formula for Calculating Bearing Velocity:
BV = PV
BP
Formula for Calculating Line Speed:
Sheave Bearings
Tapered Roller Bearings — Every 40 hours of continuous operation or every 30 days of intermittent operation.
Roller Bearings — Every 24 hours of continuous
operation or every 14 days of intermittent operation.
Line Pull x Angle Factor
Line Speed =
BV (Tread Diameter + Rope Diameter)
Shaft Diameter
Calculations can be made to find the maximum allowable
line speed for a given total sheave load. If the required line
All Rights Reserved
speed is greater than the maximum allowable line speed
calculated, then increase the shaft size and/or the hub width
and recalculate. Continue the process until the maximum
allowable line speed is equal to or exceeds the required line
speed.
Example
Using a 355 mm sheave (Stock # 917191; refer to wire
rope sheave section of General Catalog for dimensions)
with a 2091 kg line pull and an 80° angle between lines
determine maximum allowable line speed.
BP = (2091 kg x 1.53) ÷ (38.1 mm x 41.15 mm) = 2.04
kg/mm2
(line pull) (angle factor)
(Hub Width)
(Shaft Size)
Angle
0°
10°
20°
30°
40°
45°
50°
60°
70°
80°
90°
Angle Factor Multipliers
Factor
Angle
2.00
100°
1.99
110°
1.97
120°
1.93
130°
1.87
135°
1.84
140°
1.81
150°
1.73
160°
1.64
170°
1.53
180°
1.41
—
Factor
1.29
1.15
1.00
.84
.76
.68
.52
.35
.17
.00
—
BV = 0.19 ÷ 2.04 = 0.093 m/s Allowable
(PV Factor) (BP)
Line Speed =
0.093 x (304 mm + 19.1 mm) ÷ 38.1 mm = 0.789 m/s
ALLOWABLE
(BV)
Example A
(Calculations for determining total load value on single line
system.)
A gin pole truck lifting 450 kg.
(Tread Dia. + Rope Size)(Shaft Dia.)
If the application required a line speed equal to 1 m/s,
then another calculation would be necessary. Trying
another 355 mm sheave (stock # 410828) under the
same loading conditions, the results are as follows:
BP = (2090 kg x 1.53) ÷ (69.8 mm x 58.7 mm) = 0.78
kg/mm2
BV = 0.19 ÷ 0.78 = 0.244 m/s
Line Speed =
0.244 x (311.2 + 19.1) ¸69.8 = 1.15 m/s ALLOWABLE
Loads on Blocks
The Working Load Limit (WLL) for Crosby Group blocks
indicates the maximum load that should be exerted on the
block and its connecting fitting.
This total load value may be
different from the weight being
lifted or pulled by a hoisting or
hauling system. It is necessary
to determine the total load being
imposed on each block in the
system to properly determine
the rated capacity block to be
used.
A single sheave block used to
change load line direction can
be subjected to total loads
greatly different from the weight being lifted or pulled. The
total load value varies with the angle between the incoming
and departing lines to the block.
All Rights Reserved
There is no mechanical advantage to a single part load line
system, so winch line pull is equal to 450 kg or the weight
being lifted.
To determine total load on snatch block A:
A = 450 kg x 1.81 = 814.5 kg
(line pull) (factor 50° angle)
To determine total load on toggle block B:
B = 450 kg x .76 = 342 kg
(line pull) (factor 135° angle)
293
McKissick
Blocks
COMMON (PLAIN) BORE Very slow line speed, very infrequent use, low load.
ROLLER BEARING Faster line speeds, more frequent use, greater load.
Refer to manufacturer’s rating.
Reference appropriate bearing manufacturer’s catalog
for proper bearing selection procedure.
1000kg
Example B
(Calculation for determining total load value for mechanical
advantage system.)
Hoisting system lifting 1,000 kg using a traveling block.
The mechanical advantage of traveling block C is 2.00
because two (2) parts of load line support the 1,000 kg
weight. (Note that this example is simplified for
determination of resultant load on blocks. Lead line pull
will be greater than shown due to efficiency losses.) (To
determine single line pull for various bearing efficiency see
“How to Figure Line Parts” page 296).
To Determine Line Pull:
Line Pull = 1,000 kg ÷ 2.00 = 500 kg
The Reeving of Tackle Blocks
In reeving of tackle blocks, there are many methods. The
method discussed below is referred to as “Right Angle”
reeving. Please consult your rigging manual for other
methods of reeving.
RIGHT ANGLE REEVING
In reeving a pair of tackle blocks, one of which has more
than two sheaves, the hoisting rope should lead from one
of the center sheaves of the upper block to prevent toppling
and avoid injury to the rope. The two blocks should be
placed so that the sheaves in the upper block are at right
angles to those in the lower one, as shown in the following
illustrations.
Start reeving with the becket or dead end of the rope. Use
a shackle block as the upper one of a pair and a hook
block as the lower one as seen below.
Sheaves in a set of blocks revolve at different rates of speed.
Those nearest the lead line revolve at the highest rate of
speed and wear out more rapidly.
All sheaves should be kept well lubricated when in operation
to reduce friction and wear.
Right Angle Reeving Diagram
1000kg
Lead
Line
Lead
Line
Lead
Line
To determine total load on traveling block C:
C = 500 kg x 2.0 = 1,000 kg
Lead
Line
(line pull)(Factor 0° angle)
To determine total load on stationary block D:
D = 500 kg x 1.87 + 500 kg = 1,435 kg
(line pull)
(dead-end load)
(Factor 40° angle)
To determine total load on block E:
E = 500 kg x .84 = 420 kg
(line pull) (Factor 130° angle)
Double
&
Double
To determine total load on block F:
F = 500 kg x 1.41 = 705 kg
Triple
&
Double
Triple
&
Triple
Quadruple
&
Triple
(line pull) (Factor 90° angle)
•
•
294
ATTENTION
Faire attention lorsqu’un moufle est á la verticale car le risqué
de basculement existe. Le basculement se produira si la zone
de travail n’est pas stable, à
cause de mouvement de la
fleche, et du procédé de mouflage.
Si la zone de travail n’est pas
stable, posez le flasque de
moufle contre la terre.
All Rights Reserved
Sheave Size & Wire Rope Strength
Ratio A
40
30
20
15
10
8
6
4
2
1
Strength Efficiency
Compared to Catalog
Strength in %
95
93
91
89
86
Sheave Diameter
83
79
75
65
Sheave Diameter
50
Fatigue Life
Repeated bending and straightening of wire rope causes a
cyclic change of stress called “fatiguing.” Bend radius
affects wire rope fatigue life. A comparison of the relative
effect of sheave diameter on wire rope fatigue life can be
determined as shown below:
Sheave Diameter
Ratio B =
Ratio A =
Sheave Diameter
Ralative Fatigue =
Bending Life
Rope Diameter
Example
To determine the strength efficiency of 22 mm diameter wire
rope using a 440 mm diameter sheave:
Ratio A =
440 mm (sheave diameter)
= 20
22 mm(wire rope diameter)
Refer to ratio A of 20 in the table then check the column
under the heading “Strength Efficiency Compared to
Catalog Strength in %”...91% strength efficiency as
compared to the catalog strength of wire rope.
Relative Fatigue
Bending Life
10.0
6.6
3.8
2.9
2.1
1.5
1.1
Ratio B
30
25
20
18
16
14
12
Rope Diameter
Relative Fatigue Bending Life
(Sheave #1)
Relative Fatigue Bending Life
(Sheave #2)
Example
To determine the extension of fatigue life for a 20 mm wire
rope using a 600 mm diameter sheave versus a 320 mm
diameter sheave:
Ratio B =
= 30
20 mm (wire rope diameter)
Ratio B =
= 16
20 mm (wire rope diameter)
The relative fatigue bending life for a ratio B of 16 is 2.1 (see
above Table) and ratio B of 30 is 10.
10
Relative Fatigue
= 4.7
=
Bending Life
2.1
Therefore, we expect extension of fatigue life using a 600
mm diameter sheave to be 4.7 times greater than that of a
320 mm diameter sheave.
All Rights Reserved
295
McKissick
Blocks
Strength Efficiency
Bending wire rope reduces its strength. To account for the
effect of bend radius on wire rope strength when selecting
a sheave, use the table below:
How to Determine Overhauling Weights
To determine the weight of the block or overhaul ball that is
required to free fall the block, the following information is
needed: size of wire rope, number of line parts, type of
sheave bearing, length of crane boom, and drum friction (use
25 kg, unless other information is available).
Wire Rope Size
(mm)
10
11
13
14
16
19
22
25
28
32
Number
of Line
Parts
1
2
3
4
5
6
7
8
9
10
Factor A -Wire Rope Weight
Kg/m, 6 x 19 IWRC
.39
.52
.68
.88
1.07
1.55
2.11
2.75
3.48
4.30
Factor B -Overhaul Factors
Roller Bearing
Bronze Bushed
Sheaves
Sheaves
1.03
1.05
2.07
2.15
3.15
3.28
4.25
4.48
5.38
5.72
6.54
7.03
7.73
8.39
8.94
9.80
10.20
11.30
11.50
12.80
How to Figure Line Parts
Sheaves in a system of blocks rotate at different rates of
speed, and have different loads. When raising and lowering,
the line tension is not equal throughout the system. To help
figure the number of parts of line to be used for a given load,
or the line pull required for a given load, (for example, use
Reeving Diagram on page 294. Only numbered lines shall
be used in the calculation). The following ratio table is
provided with examples of how to use it. The ratios are
applicable for blocks as shown on page 295 and also
independent sheave systems that line is reeved through.
Ratio A
Bronze Bushed
Sheaves
.96
1.87
2.75
3.59
4.39
5.16
5.90
6.60
7.27
7.91
8.52
9.11
9.68
10.20
10.70
11.20
11.70
12.20
12.60
13.00
Ratio B
Anti-Friction
Bearing Sheaves
.98
1.98
2.88
3.81
4.71
5.60
6.47
7.32
8.16
8.98
9.79
10.60
11.40
12.10
12.90
13.60
14.30
15.00
15.70
16.40
Total Load to be Lifted
Single Line Pull (kg)
Ratio A or B =
The Formula is:
Required Block Weight = [(Boom Length x Factor A) +
Drum Friction] x Factor B
Example:
To determine the required block or overhaul weight using 5
parts of 22 mm diameter wire rope, a 15 m boom and roller
bearing sheaves:
Required
Block
Weight
= [(15 m x 2.11)+ 25 kg] x 5.38 = 305 kg
(Boom length)
(Drum Friction)
(Factor A)
(Factor B)
Number
of
Line Parts
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
After calculation Ratio A or B, consult table to determine
number of parts of line.
Examples:
To find the number of parts of line needed when weight
of load and single line pull are known, and using Bronze
Bushed Sheaves.
Ratio A =
72 t (load to be lifted)
8 t (single line pull)
= 9
(Ratio A)
In table above refer to ratio 9 or next highest number, then
check column under heading “Number of Line Parts” = 12
parts of line to be used for this load.
To find the single line pull needed when weight of load
and number of parts of line are known, and using AntiFriction Bearing Sheaves.
Single Line Pull =
68 t (load to be lifted)
7.32 (Ratio B of 8 part line)
= 9.29 t
9.29 t single line pull required to lift this load on 8 parts of
line.
296
All Rights Reserved
To find the lift capacity when the parts of line and single
line pull are known, and using anti-friction bearing
sheaves.
10 t
x 4.71
= 47.1 t
(single line pull)
(ratio B of 5 parts of line)
(Lift Capacity)
10 t single line pull with 5 parts of line will accommodate
47.1 t. lift capacity.
How to Find Your Nearest Crosby
Distributor
To locate your nearest Crosby Distributor, call:
IN U.S.A. — Crosby Customer Service Department at
(800) 772-1500
IN CANADA — Crosby Canada Ltd. at (905) 451-9261
IN EUROPE — N.V. Crosby Europe at 32 15 757125
Repairs
For repair of blocks, contact the following numbers for return
material authorization.
IN U.S.A. — Crosby Enginnered Products Group at
(800) 777-1555
IN CANADA — Crosby Canada Ltd. at (905)451-9261
IN EUROPE — N.V. Crosby Europe at 32 15 757125
Your block, after receipt by Crosby, will be inspected and a
free estimate of repair charges will bw provided.
Authorization for repairs from block owners must be given
to Crosby before repairs are made. Transporation charges,
both to and from factory, are to be paid by the block owner.
Additional Information
For information concerning parts, special application, or
situations requiring other features, contact:
McKissick
Blocks
U.S.A.
The Crosby Group, Inc.
P.O. Box 3128
Tulsa, OK 74101-3128
(918) 834-4611
FAX (918) 832-0940
www.thecrosbygroup.com
crosbygroup@thecrosbygroup.com
CANADA
Crosby Canada Ltd.
145 Heart Lake Road
Brampton, Ontario, Canada L6W 3K3
(905) 451-9261
FAX (877)260-5106
www.crosby.ca
sales@crosby.ca
EUROPE
N.V. Crosby Europe
Leuvensebaan 51
2580 Putte
(Mechelen) Belgium
32-15-75-71-25
FAX 32-15-75-37-64
www.thecrosbygroup.com
sales@crosbyeu.com
All Rights Reserved
297
McKissick® Pull Test Capabilities
Two 24", 5 sheave blocks being tested in McKissick’s pull testing facility.
•
•
•
•
•
•
Proof Test Capability (Blocks) — 1000 short tons
Ultimate Test Capability — 800 short tons
Proof Test Capability (Shackles) — 2000 metric tonnes
Full reeving block testing by using winches to 1000 short tons
Complete laboratory facilities for all phases of metalurgical testing and inspection
Certifications available for all national standards, American Bureau of Shipping,
Lloyd’s Register of Shipping, Det Norske Veritas, etc.
All Rights Reserved
298

McKissick® Blocks

Transcription

Similar documents