File Now

I.
II.
Purpose
This specification describes the key requirement metrics for KETG Type A tubular
lamps. .
Scope
This specification defines applies to KETG T8 Type A tubular lamp products. Type A
products operate directly off AC mains.
III.
Critical Requirements
a. Summary of key performance
1. Efficiency: 100 lm/W under nominal operating voltage
2. Life time: 50,000 hrs/ 70% luminous maintenance
3. Supply voltage: 100-277V nominal, 95-305 worst case, 50-60Hz
4. Light distribution: 240 degrees beam angle
5. CR: > 80
6. Power factor: >0.9
7. Ambient temperature -20°C ...+45°C
8. Environmental Safety: Hg free, no UV
9. Harmonic Distortion: < 20%
b. Internal Architecture
Type A lamps consist primarily of a power supply unit (PSU) and a light engine.
1. PSU
All Type A power supplies use non-isolated buck/boost topology to ensure high
efficiency and wide operating range.
2. Light engine
The light engine employs Al PCB mounted LEDs. The table below lists actual LED usage
on these light engines.
Length
4 Feet
2 Feet
LED size Elements/Segment
(in parallel)
2835
8
2835
5
c. Specification Summary
Part Number
T84-A-004000
T82-A-00-
Wattage
16
10
Length
4'
2'
# segments
(in series)
19
19
Total
Luminous
Flux(lm)
1600
1000
Color
Rendering
Index
80
80
Color
Temperature
4000
4000
578 Rockrose Court – Incline Village – Nevada 89450 Tel: (925) 245-6200 Fax: (925) 245-6222
IV.
4000
T84-A-005000
T82-A-005000
T84-A-006000
T82-A-006000
16
4'
1600
80
5000
16
4'
1600
80
6000
10
10
2'
2'
1000
1000
80
80
5000
6000
Operating Procedures
a. Wiring: Type A lamps connect to AC power using pins on opposite ends. Pins on the same
end are shorted internally so it is necessary to connect only one in each pair.
b. Connect directly to AC mains. Use of ballast or starter is not allowed.
c. Switch off mains supply before installing/removing lamp.
d. Use in fully enclosed fixtures may affect life performance.
e. Not for use in emergency lighting circuits or life-critical applications.
V.
Maintenance Requirements
This document is to be updated whenever there is a material change to
a.
b.
c.
d.
PSU schematics
PSU component values
LED chip
Chip-on-frame procedures and materials
e. Tube material
VI.
Security Requirements
External release is authorized only under NDA and in individually watermarked form.
VII.
Referenced Documents
a. PSU schematic and layout: PSU-T8A-DSN
b. LED specification
c. PVC material specification
d. applicable standards documents:
EN 55015
Limits and methods of measurement of radio disturbance characteristics of electrical lighting
EN 61000-3-3
Limits for harmonic current emissions (equipment rated current <=16A)
EN 61547
Limitation of voltage fluctuations and flicker in low voltage supply systems (equipment rated
current <=16A)
EN 55015
578 Rockrose Court – Incline Village – Nevada 89450 Tel: (925) 245-6200 Fax: (925) 245-6222
Specification for equipment for general lighting purposes. EMC Immunity requirements
EN62493:2010
Assessment of lighting equipment related to human exposure to electromagnetic field
IEC 62471
Photo biological safety of lamps and lamp systems
IEC 60061-1
Lamp Caps
IEC 61195 IEC
Based Safety Standard Requirements for Double-capped Fluorescent Lamps
IEC 60598-1
Luminaires – Part 1: General requirements and tests
IEC 60598-2
Luminaires – Part 2: Particular requirements (all sections)
IEC 62031
LED modules for general lighting-Safety specifications
IEC 61347-2-13
Particular requirements for DC or AC supplied electronic control gear for LED modules
578 Rockrose Court – Incline Village – Nevada 89450 Tel: (925) 245-6200 Fax: (925) 245-6222