A Free Safety Offer From Ruger

A Free Safety Offer From Ruger
Do you own an “Old Model” (pre-1973) Ruger Single-Six, Blackhawk,
Super Blackhawk, or Bearcat single action revolver like these?
The patented Ruger Conversion Kit is an
entirely new operating system for these
revolvers. It can help prevent accidental
discharges caused by a drop or blow to the
hammer if the user has failed to take the
basic safety precaution of keeping the
hammer down on an empty chamber.
That’s very important!
This mechanism can be factory-installed
without any further alteration. The frame
and other major parts will not be affected
by this Conversion. The value of the gun
will not be impaired, and we will return
your original parts for collector’s purposes.
To receive a FREE factory safety
Conversion, write to us at Sturm, Ruger
and Company, Inc., Dept. KC, 411
Sunapee Street, Newport, NH 03773. We
will provide you with a shipping container
and instructions. You only pay initial
shipping to our factory. We will cover all
other charges including return shipping
costs. Please write to us without delay if
you have one of these guns, and tell your
friends about the availability of this kit.
Remember that the safest way to carry any
older single-action revolver, regardless of
manufacturer, is with the hammer down on
an empty chamber.
Three frame screws identify the “old model”
Single-Six, Blackhawk, and Super Blackhawk
made from 1953 to 1972.
Serial numbers below 93-00000 identify old
Bearcat and Super Bearcat models made from
1958 to 1972.
If your revolver has the words “New
Model,” “Bisley,” or “Vaquero” on the
frame, this offer is not applicable. Please
write to us at:
Sturm, Ruger & Company, Inc.
Department KC
411 Sunapee Street
Newport, NH 03773
for full details and a FREE shipping box.
Arms Makers for Responsible Citizens®
FREE instruction manuals for all Ruger
firearms are available online at www.ruger.com
RUGER LCP
®
®
PRODUCT SAFETY
WARNING AND
RECALL NOTICE
In 2008, Ruger received a small number of reports from the field indicating that LCP pistols
could discharge when dropped onto a hard surface with a round in the chamber. We are firmly
committed to safety and would like to retrofit all older LCP Pistols. The retrofit involves
installation of an upgraded hammer mechanism at no charge to the customer.
We want to remind gun users that, for maximum safety when carrying any pistol with a loaded magazine in
place, the chamber should be empty, and the slide should be closed. Any gun may fire if dropped or struck.
How to determine if your pistol needs the retrofit:
• All LCP pistols with serial number prefix "371" and higher (371-xxxxx) have been
manufactured with the new hammer mechanism and are NOT affected by the recall and DO
Figure 1
NOT need to be returned.
• If your LCP has a serial number prefix "370" you will need to check the flat portion of the slot just behind and below the hammer for a
diamond mark. As shown in Figure 1, LCPs marked with the diamond have had the new hammer mechanism installed and DO NOT
need to be returned.
• If your LCP has the "370" serial number prefix and DOES NOT HAVE the diamond mark, we recommend you have your LCP
retrofitted with the upgraded hammer mechanism at no charge.
How to arrange to have your pistol retrofitted:
Step 1 - Contact us and provide your name, address, telephone number and LCP serial number. Provide your information by any of
the following: Email: LCPRecall@ruger.com; Fax: (928) 541-8873; Phone: LCP Recall Hotline 1-800-784-3701 (available Monday Friday, 9:00 a.m. to 8:00 p.m. EDT).
Step 2 - We will send you a shipping label and package with instructions so you can return your pistol to us FREE of charge.
Step 3 - We will install the new hammer mechanism, plus some other functional upgrades that we added since the LCP’s introduction,
and return your LCP to you, all FREE of charge. When we do, we also will send you a FREE magazine as a “thank you” for your
patience and cooperation. We will make every effort to return your pistol within one week of receipt.
RUGER SR9
®
®
PRODUCT SAFETY
WARNING AND
RECALL NOTICE
In 2008, we determined that some Ruger SR9 pistols manufactured between October 2007 and April 2008 could, under certain
conditions, fire if dropped with their manual safeties in the "off" or "fire" position. The pistols will not fire if the manual safety is in the "on"
or "safe" position.
We will retrofit all affected SR9 pistols (those with serial number 330-29999 or lower) with these parts at no charge to our customers. In
order to ensure correct fitting, the new parts must be installed at our Ruger factory in Prescott, Arizona. We will remove the old parts
and install the new trigger group promptly, at no charge, and will return the pistol to you. The old parts will not be returned.
How to determine if your pistol needs the retrofit:
Figure 2
It is easy to determine if your pistol has been retrofitted by simply looking at it. Although both
the old and new trigger group have a two-stage trigger, the original design had an inner “shoe”
that was not visible and, therefore, appeared to be a single trigger (See Figure 2). The new
trigger design incorporates a visible inner trigger of a blade design (See Figure 3).
If you own an SR9 Pistol bearing a serial number below 30000 (that is, 330-29999 or less) that
has not been retrofitted, please contact us immediately to arrange return of the pistol.
How to arrange to have your pistol retrofitted:
Step 1 - Contact us and provide your name, address, telephone number and SR9 serial
number. Provide your information by any of the following: Email: SR9Recall@ruger.com;
Fax: (928) 541-8873; Phone: SR9 Recall Hotline 1-800-784-3701 (available Monday - Friday,
9:00 a.m. to 8:00 p.m. EDT).
Original trigger group – Pistol needs retrofit
Figure 3
Step 2 - We will send you a shipping box with instructions so you can return your pistol to us
FREE of charge.
Step 3 - We will install the new trigger group in your SR9 and return it to you FREE of charge.
When we do, we also will send you a FREE magazine as a “thank you” for your patience and
cooperation. We will make every effort to return your pistol within one week, so we will not ask
you to send it to us until we are ready to receive it.
New trigger group – Pistol does not need retrofit
Do not load or fire your pistol until it has been factory retrofitted with these new parts! If you must fire your pistol, be sure to keep the
manual safety in the "on" or "safe" position except when you are actually firing.