service manual - PORTAL DA ELETRÔNICA

Transcription

service manual - PORTAL DA ELETRÔNICA
HCD-D290/G3300/XB3
SERVICE MANUAL
US Model
Canadian Model
HCD-D290/G3300
AEP Model
UK Model
E Model
Australian Model
PX Model
HCD-XB3
HCD-D290, HCD-G3300, HCD-XB3 is the
tuner, deck, CD and amplifier section in
LBT-D290, LBT-G3300, LBT-XB3.
Photo: HCD-XB3
Model Name Using Similar Mechanism
CD Mechanism Type
CD
Section
Base Unit Name
BU-5BD29AL
Optical Pick-up Name
Tape deck
Section
KSS-213D/Q-NP
Model Name Using Similar Mechanism
Tape Transport Mechanism Type
NEW
CDM37L-5BD29AL
HCD-H881
TCM-220WR2
SPECIFICATIONS
For the U.S. model
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION:
With 8 ohm loads, both channels driven, from 70-20,000 Hz; rated 100 watts
per channel minimum RMS power, with no more than 0.9 % total harmonic
distortion from 250 milliwatts to rated output.
Amplifier section
DIN power output
AEP, UK, East European models: 55+55 watts (6 ohms at 1 kHz, DIN)
Continuous RMS power output
Canadian model:
100+100 watts
(8 ohms at 1 kHz, 5%)
Argentine, Australian, E, Mexican,
PX models:
70+70 watts
(6 ohms at 1kHz, 10% THD)
AEP, UK, East European models: 65+65 watts
(6 ohms at 1kHz, 100% THD)
Peak music power output
Argentine, Australian, E, Mexican,
PX models:
1000 watts
Music power output
AEP, UK, East European models: 100+100 watts
Inputs
PHONO IN (phono jack):
sensitivity 3 mV, impedance 47 kilohms
VIDEO (AUDIO) IN (phono jack):sensitivity 250 mV, impedance 47 kilohms
MIX MIC (phono jack):
sensitivity 1 mV, impedance 10 kilohms
Outputs
PHONES (stereo phone jack):
accepts headphones of 8 odms or more
SPEAKER:
US, Canadian models:
accepts impeadance of 8 to 16 ohms.
Other models
accepts impeadance of 6 to 16 ohms.
– Continued on next page –
COMPACT DISC DECK RECEIVER
MICROFILM
CD player section
System
Laser
Laser output
Wavelength
Frequency response
Signal-to-noise ratio
Dynamic range
General
compact disc and digital audio system
Semiconductor laser (λ = 780nm).
Emission
duration: continuous
Max. 44.6µF*
*This output is the value measured at a distance of
200 mm from the objective lens surface on the
Optical Pick-up Block with 7 mm aperture.
780 - 790 nm
2 Hz - 20 kHz (±0.5 dB)
More than 90 dB
More than 90 dB
Tape player section
Recording system
4-track 2-channel stereo
Frequency response (DOLBY NR OFF)
60 - 13,000 Hz (±3 dB), using a Sony
TYPE I cassette
60 - 14,000 Hz (±3 dB), using a Sony
TYPE II cassette
Wow and flutter
±0.15% W. Peak (IEC)
0.1% W. RMS (NAB)
±0.2% W. Peak (DIN)
Power requirements
US, Canadian models:
Mexican model:
Australian model:
AEP, UK, East European
models:
Other models:
Power consumption
US, Canadian models:
AEP, UK, East European
models:
Other models:
Dimensions (w/h/d)
Mass
(D290)
(G3300)
(XB3)
Supplied accessories:
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
US, Canadian models:
87.5 - 108.0 MHz (100 kHz step)
AEP, UK models:
87.5 - 108.0 MHz (50 kHz step)
East European model
FM:
87.5 -108.0 MHz (50 kHz step)
65.0 - 74.0 MHz (10 kHz step) OIRT
UKV:
65.0 - 74.0 MHz (10 kHz step) POLAR STEREO
Other models:
87.5 -108.0 MHz (50 kHz step)
Antenna
FM wire antenna
Antenna terminals
75 ohm unbalanced
Intermediate frequency 10.7 MHz
AM tuner section
Tuning range
US, Canadian models:
530 - 1,710 KHz (with the tuning interval set at 10
kHz)
531 - 1,710 KHz (with the tuning interval set at 9
kHz)
AEP, UK, East European
models:
MW:
531 - 1,602 kHz
(with the tuning interval set at 9 kHz)
LW:
153 - 279 kHz
(with the tuning interval set at 3 kHz)
Other models:
531 - 1,602 kHz
(with the tuning interval set at 9 kHz)
530 - 1,710 KHz
(with the tuning interval set at 10 kHz)
Antenna
AM loop antenna, External antenna terminals
Intermediate frequency 450 kHz
120 V AC, 60 Hz
120 V AC, 50/60 Hz
220 - 240 V AC, 50/60 Hz
220 - 230 V AC, 50/60 Hz
110 - 120 V or 220 - 240 V
AC, 50/60 Hz Adjustable with voltage selector
170 watts
130 watts
140 watts
Approx. 355 x 425 x 435 mm (14 x 16 3/4 x 17 1/4
in) incl. projecting parts and controls
Approx. 11.5 kg (25 lb 6 oz.)
Approx. 11.6kg (25 lb 9 oz.)
Approx. 10.6kg (23 lb 6 oz.)
AM loop antenna (1)
Remote RM-SD70 (1)
Sony SUM-3 (NS)
batteries (2)
FM wire antenna (1)
Design and specifications are subject to change without notice.
–2–
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage.
Check leakage as described below.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
This appliance is classified as a CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT MARKING is located on
the rear exterior.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microampers.). Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The “limit” indication is 0.75
V, so analog meters must have an accurate low-voltage scale.
The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2 V AC range are suitable. (See Fig. A)
To Exposed Metal
Parts on Set
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
The following caution label is located inside the unit.
0.15 µF
1.5 k Ω
AC
voltmeter
(0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
Dolby noise reduction manufactured under license from Dolby
Laboratories Licensing Corporation.
“DOLBY” and the double-D symbol a are trademarks of Dolby
Laboratories Licensing Corporation.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED
LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE !
SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE
DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ
DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES
NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
–3–
TABLE OF CONTENTS
1.
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
GENERAL
Getting Started ..................................................................
Basic Operations ...............................................................
The CD Player ..................................................................
The Tape Deck ..................................................................
DJ Effects .........................................................................
Sound Adjustment ............................................................
Other Features ..................................................................
5
8
12
14
15
16
18
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
2.
DISASSEMBLY ........................................................... 22
3.
TEST MODE ................................................................ 30
4.
MECHANICAL ADJUSTMENTS .......................... 32
5.
ELECTRICAL ADJUSTMENTS
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
DECK Section .................................................................. 32
Tuner Section .................................................................... 35
CD Section ........................................................................ 36
MODEL IDENTIFICATION
– BACK PANEL –
6.
NOTES ON LASER DIODE EMISSION CHECK
DIAGRAMS
6-1. Block Diagrams
Tuner Section
(US, CND, E, AR, MX, AUS, PX modes) ........................
Tuner Section
(AEP, UK models) ............................................................
CD Section ........................................................................
Main Section .....................................................................
6-2. Schematic Diagram – BD Section – .................................
6-3. Printed Wiring Board – BD Section – ..............................
6-4. Schematic Diagram – CD Motor Section – .....................
6-5. Printed Wiring Boards – CD Motor Section – .................
6-6. Schematic Diagram – Tuner Section –
(US, CND, E, AR, MX, AUS, PX models) ......................
6-7. Printed Wiring Board – Tuner Section –
(US, CND, E, AR, MX, AUS, PX models) ......................
6-8. Printed Wiring Board – Tuner Section –
(AEP, UK models) ............................................................
6-9. Schematic Diagram – Tuner Section –
(AEP, UK models) ............................................................
6-10. Printed Wiring Boards – Deck Section – .........................
6-11. Schematic Diagram – Deck Section – .............................
6-12. Schematic Diagram – Main Section – .............................
6-13. Printed Wiring board – Main Section – ...........................
6-14. Schematic Diagrm – Panel Section – ...............................
6-15. Printed Wiring Boards – Panel Section – .........................
6-16. Printed Wiring Boards – Power Section – ........................
6-17. Schematic Diagram – Power Section – ............................
6-18. IC Pin Function Description .............................................
40
PARTS No.
41
42
43
45
47
49
51
53
55
58
59
61
63
67
71
74
77
81
83
88
7.
EXPLODED VIEWS .................................................. 92
8.
ELECTRICAL PARTS LIST ................................... 101
• Abbreviation
CND : Canadian model
MX
: Mexican model
AUS : Australian model
AR
: Argentine model.
–4–
MODEL
PARTS No.
D290: US model
4-987-043-0π
D290: Canadian model
4-987-043-1π
G3300: US model
4-987-043-2π
G3300: Canadian model
4-987-043-3π
XB3: AEP, UK models
4-987-043-4π
XB3: East European model
4-987-043-6π
XB3: Argentine, E models
4-987-134-0π
XB3: Australian model
4-987-134-1π
XB3: PX model
4-987-134-2π
XB3: Mexican model
4-987-134-3π
SECTION 1
GENERAL
–5–
This section is extracted
from instruction manual.
–6–
–7–
–8–
–9–
– 10 –
– 11 –
– 12 –
– 13 –
– 14 –
– 15 –
– 16 –
– 17 –
– 18 –
– 19 –
– 20 –
– 21 –
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
CASE
(Page 22)
FRONT PANEL
SECTION
(Page 23)
MAIN
SECTION
(Page 24)
CD MECHANISM
DECK SECTION
(Page 24)
BASE UNIT
(Page 27)
BD BOARD
(Page 28)
DISC TABLE
(Page 27)
TAPE MECHANISM
DECK SECTION
(Page 25)
AUDIO BOARD
(Page 29)
CAPSTAN MOTOR
(Page 29)
CASSETTE
LID ASS’Y
(Page 25)
PANEL (A)/(B)
SUB ASS’Y
(Page 26)
CD LID ASS’Y
SECTION
(Page 26)
MAIN BOARD
(Page 23)
Note: Follow the disassembly procedure in the numerical order given.
CASE
3 case
1 three screws
(case 3 point)
1 three screws
(case 3 point)
2 seven screws
(BVTT 3 × 6)
– 22 –
OPTICAL
PICK-UP
(Page 28)
SLED
MOTOR
(Page 28)
FRONT PANEL SECTION
1 three frat wires
(CN102, 205, 206)
3 front panel section
2 four screws
(BVTP 3 × 8)
MAIN BOARD
6 back panel
5 power cord
4 ereven screws
(BVTP 3 × 8)
3 connector
(CN901)
1 two flat wires
(CN1, 202)
9 MAIN board
IC201
8 connector
(CN101)
2 connector
(CN203)
– 23 –
7 two screws
(BVTP 3 × 8)
1 flat wire (CN202)
MAIN SECTION
2 connector
(CN203)
4 main section
3 two screws
(BVTP 3 × 8)
3 screw
(BVTP 3 × 8)
3 two screws
(BVTP 3 × 8)
CD MECHANISM DECK SECTION
3 five screws
(BVTP 3 × 8)
4 CD mechanism
deck section
2 flat wire
and lead wire
1 Open the clamp.
– 24 –
TAPE MECHANISM DECK SECTION
4 three screws
(BVTP 2.6 × 8)
4 three screws
(BVTP 2.6 × 8)
5 Remove the tape mechanism
deck section to direction of the arrow A.
3 two flat wires
(CN601, 1001)
A
2 Open the
cassette lids.
1 Push the
two buttons.
CASSETTE LID ASS’Y
3 two bracket
2 two screws
(BVTP 2.6 × 8)
1 two springs
– 25 –
CD LID ASS’Y SECTION
5 connector
(CN671)
6 four screws
(BVTP 2.6 × 8)
7 CD lid ass’y
4 connector
(CN661)
2 four screws
(BVTP 2.6 × 8)
3 CD-B1 SW board
1 connector
(CN642)
PANEL (A) / (B) SUB ASS’Y
1 connector
(CN612)
3 two claws
2 four screws
(BVTP 2.6 × 8)
4 panel (A) sub ass’y
5 two claws
6 panel (B) sub ass’y
– 26 –
BASE UNIT
3 base unit
1 yoke bracket
2 boss
DISC TABLE
Note:
When the disc table is installed, adjust the positions
of roller cam and mark z as shown in the figure, then
set to the groove of disc table.
A
3 step screw
1 screw
(BVTP 3 × 8)
2 bracket (BU)
1 screw
(BVTP 3 × 8)
4 disc table
A
– 27 –
BD BOARD
1 two screws
(PTPWH M2.6 × 6)
1 two screws
(PTPWH M2.6 × 6)
2 optical pick-up
section
3 two springs
3 two springs
5 screw
(BVTP 2.6 × 8)
4 flat wire
(CN101)
6 Removal
the four solders.
7 BD board
limit switch
OPTICAL PICK-UP, SLED MOTOR
3 optical pick-up
4 two screws
(P2 × 3)
2 sled shaft
5 sled motor
1 claw
– 28 –
AUDIO BOARD
2 two rivets
1 connector
(CN651)
4 four screws
(BTP 2.6 × 4)
3 Break the soldering of two
flexible flat cables.
5 MD board
CAPSTAN MOTOR
4 Removal the capstan motor
to direction of the arrow.
2 two screws
(BTP 2.6 × 8)
1 Break the soldering of
motor lead.
3 claw
5 Hang the
two belts.
– 29 –
SECTION 3
TEST MODE
[MC Cold Reset]
• The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning the
set to the customer.
Procedure:
1. Press three buttons GROOVE , ENTER/NEXT , and
DISC 1 simultaneously.
2. The fluorescent indicator tube becomes blank instantaneously,
and the set is reset.
[CD Delivery Mode]
• This mode moves the pickup to the position durable to vibration.
Use this mode when returning the set to the customer after repair.
Procedure:
1. Press POWER button to turn the set ON.
2. Press PLAY MODE button and POWER button simultaneously.
3. A message “LOCK” is displayed on the fluorescent indicator
tube, and the CD delivery mode is set.
[MC Hot Reset]
• This mode resets the set with the preset data kept stored in the
memory. The hot reset mode functions same as if the power cord
is plugged in and out.
Procedure:
1. Press three buttons GROOVE , ENTER/NEXT , and
DISC 2 simultaneously.
2. The fluorescent indicator tube becomes blank instantaneously,
and the set is reset.
[Sled Servo Mode]
• This mode can run the CD sled motor freely. Use this mode, for
instance, when cleaning the pickup.
Procedure:
1. Select the function “CD”.
2. Press three buttons GROOVE , ENTER/NEXT , and
FLASH simultaneously.
3. The Sled Servo mode is selected, if “CD” is blanking on the
fluorescent indicator tube.
4. With the CD in stop status, press ) button in CD section to
move the pickup to outside track, or 0 button to inside track.
5. To exit from this mode, perform as follows:
1) Move the pickup to the most inside track.
2) Press three buttons in the same manner as step 2.
Note:
• Always move the pickup to most inside track when exiting from
this mode. Otherwise, a disc will not be unloaded.
• Do not run the sled motor excessively, otherwise the gear can be
chipped.
[Change-over of AM Tuner Step between 9kHz and 10kHz]
• A step of AM channels can be changed over between 9kHz and
10kHz.
Procedure:
1. Press POWER button to turn the set ON.
2. Select the function “TUNER”, and press TUNER/BAND
button to select the BAND “AM”.
3. Press POWER button to turn the set OFF.
4. Press ENTER/NEXT and POWER buttons simultaneously,
and the display of fluorescent indicator tube changes to “AM
9k STEP” or “AM 10k STEP”, and thus the channel step is
changed over.
[LED and Fluorescent Indicator Tube All Lit, Key Check
Mode]
Procedure:
1. Press three buttons GROOVE , ENTER/NEXT , and DISC 3
simultaneously.
2. LEDs and fluorescent indicator tube are all turned on.
Press DISC 2 button, and the key check mode is activated.
3. In the key check mode, the fluorescent indicator tube displays
“K 1 V0 J0”. Each time a button is pressed, “K”value increases.
However, once a button is pressed, it is no longer taken into
account.
“J” Value increases like 1, 2, 3 ... if rotating JOG knob in “+”
direction, or it decreases like 0, 9, 8 ... if rotating in “–” direction.
“V” Value increases like 1, 2, 3 ... if rotating VOLUME knob
in “+” direction, or it decreases like 0, 9, 8 ... if rotating in “–”
direction.
4. To exit from this mode, press three buttons in the same manner
as step 1, or disconnect the power cord.
[Change-over of FUNCTION Name]
• The FUNCTION name of external input terminal can be changed
over to VIDEO or MD. With the FUNCTION selected to “MD”,
about 5dB mute is applied to the input gain.
Procedure:
1. Press POWER button to turn the set OFF.
2. Press POWER button together with FUNCTION button, and
the power is turned on, the display of fluorescent indicator tube
changes to “MD” or “VIDEO” instantaneously, and thus the
FUNCTION is changed over.
– 30 –
[Aging Mode]
This mode can be used for operation check of CD section and tape
deck section.
• If an error occurred:
The aging operation stops.
• If no error occurs:
The aging operation continues repeatedly.
1. Aging Mode in CD Section
1-1. Operating Method of Aging Mode
1. Set discs in DISC 1 and DISC 3 trays.
2. Select the function “CD”.
3. Press three buttons GROOVE , ENTER/NEXT , and
DISC 5 simultaneously.
4. The aging mode is activated, if a roulette mark on the fluorescent indicator tube is blinking.
5. In the aging mode, the aging is executed in a sequence given
in “1-2. Operation during Aging Mode”.
The aging continues unless an alarm occurred.
6. To exit from the aging mode, press POWER button to turn
the set OFF.
• If a button other than buttons In CD section is pressed during
aging, the aging in the CD section is finished.
• To execute aging to the tape deck section successively, press ·
button in the deck A.
“AGING” is displayed on the fluorescent indicator tube. (For the
aging in tape deck, see “2. Aging Mode in Tape Deck Section”.
8. To exit from the aging mode, press POWER button to turn
the set OFF.
2-2. Operation during Aging Mode
In the aging mode, the program is executed in the following sequence.
1. A tape on FWD side is played for one minute.
2. PAUSE STOP is made.
3. Recording is made for 3 minutes. (For the deck not having
the record function, the play is executed.)
4. FF is executed up to the end of tape.
5. A tape is reversed, and the tape on REV side is played for
one minute.
6. PAUSE STOP is made.
7. Recording is made for 3 minutes. (For the deck not having
the record function, the play is executed.)
8. FF is executed up to the end of tape.
9. Steps 1 through 8 are executed for the other deck.
10. Steps 1 through 9 are repeated unless an alarm occurred.
2-3. Deck Selection Sequence
• During the aging mode, decks are selected in the following sequence:
Deck A (FWD) → Deck A (REV)
↑
↓
Deck B (REV) ← Deck B (FWD)
1-2. Operation during aging Mode
In the aging mode, the program is executed in the following sequence.
1. The disc tray turns to select a disc. (For a disc selection
sequence, see Section 1-3.)
2. TOC of disc is read.
3. The pickup accesses to the last track.
4. Steps 1 through 3 are repeated.
1-3. Disc Selection Sequence
• During the aging mode, discs are selected in the following sequence:
Disc 1 → Disc 3
↑
↓
Disc 3 ← Disc 1
2. Aging Mode in Tape Deck Section
2-1. Operating Method of Aging Mode
1. Load a commercially available 10-minute tape into the decks
A and B respectively.
(If a 10-minute tape is not available, another tape may be
used but a cycle time will be longer.)
2. Select the function “TAPE”.
3. Rewind tapes in advance by pressing 0 button respectively on decks A and B.
4. Press three buttons GROOVE , ENTER/NEXT , and
DISC 5 simultaneously.
5. Press · button on deck A. (This button triggers the aging mode.)
6. The aging mode is activated if “AGING A” is displayed on
the fluorescent indicator tube.
7. In the aging mode, the aging is executed in a sequence given
in “2-2. Operation during Aging Mode”.
The aging continues unless an alarm occurred.
– 31 –
SECTION 4
MECHANISM ADJUSTMENTS
SECTION 5
ELECTRICAL ADJUSTMENTS
PRECAUTION
1. Clean the following parts with a denatured-alcohol-moistened
swab:
record/playback head
pinch roller
erase head
rubber belts
capstan
idlers
2. Demagnetize the record/playback head with a head demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the
parts adjusted.
5. The adjustments should be performed with the rated power supply voltage unless otherwise noted.
• Torque Measurement
Mode
Torque Meter
Meter Reading
Forward
CQ-102C
36 to 61g·cm
(0.50 – 0.84 oz·inch)
Forward
Back Tension
CQ-102C
2 to 6g·cm
(0.026 – 0.082 oz·inch)
CQ-102RC
36 to 61g·cm
(0.50 – 0.84 oz·inch)
Reverse
Reverse
Back Tension
FF, REW
CQ-102RC
CQ-201B
0dB=0.775V
1. Demagnetize the record/playback head with a head demagnetizer. (Do not bring the head demagnetizer close to the erase
head.)
2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the
parts adjust.
4. The adjustments should be performed with the rated power supply voltage unless otherwise noted.
5. The adjustments should be performed in the order given in this
service manual. (As a general rule, playback circuit adjustment
should be completed before performing recording circuit adjustment.)
6. The adjustments should be performed for both L-CH and R-ch.
7. Switches and controls should be set as follows unless otherwise
specified.
8. Set to test mode. (Press key switch same time GROOVE
ENTER/NEXT and DISC 4 button.)
•
Test Tape
2 to 6g·cm
(0.026 – 0.082 oz·inch)
61 to 143g·cm
(0.85 – 1.98 oz·inch)
Tape
Signal
Used for
P-4-A100
10kHz, –10 dB
Azimuth Adjustment
WS-48B
3kHz, 0dB
Tape Speed Adjustment
P-4-L300
315Hz 0dB
Level Adjustment
Record/Playback Head Azimuth Adjustment
• Tape Tension Measurement
Mode
DECK SECTION
DECK A
Tension Meter
Meter Reading
Forward
CQ-403A
more than 100g (3.52 oz)
Reverse
CQ-403R
more than 100g (3.52 oz)
DECK B
Note: Perform this adjustments for both decks
Procedure:
1. Mode: Playback (FWD)
test tape
P-4-A100
(10KHz, –10dB)
main board
CN207
Pin 1 (L-CH)
Pin 3 (R-CH) level meter
set
+
–
main board
CN207
Pin 2
– 32 –
2. Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1dB of peak.
within
1dB
L-CH
peak
within
1dB
output
level
Screw
position
Tape Speed Adjustment DECK A
Note: Start the Tape Speed adjustment as below after setting to the
test mode.
In the test mode, the tape speed is high during pressing the
H. SPEED DUBB button.
Procedure:
1. Turn the power switch on.
2. Press the GROOVE button, ENTER/NEXT button and
DISC 4 button simultaneously.
To exit from the test mode, press the POWER button.
Mode: Playback (FWD)
R-CH
peak
L-CH
peak
test tape
WS-48B
(3 kHz, 0 dB)
Screw
position
R-CH
peak
frequency counter
+
–
set
3. Mode: Playback (FWD)
test tape
P-4-A100
(10kHz, –10dB)
L-CH
main board
CN207 (Pin 1 : L-CH)
(Pin 3 :R-CH)
oscilloscope
pin 1
pin 2
main
board
CN207
set
L
V
H
R
R-CH
pin 3
waveform of oscilloscope
in phase 45°
good
90° 135° 180°
wrong
4. Repeat steps 1 to 3 in playback (REV) mode.
5. After the adjustments, apply suitable locking compound to the
pats adjusted.
Adjustment Location: Record/Playback Head (Deck A and B)
and main board.
1. Insert the WS-48B into the deck A and the blank tape into the
deck B.
2. Press the REC button and · button on the deck B. Then
the deck B is at recording mode.
3. Set the deck A to playback mode.
4. Keep pressing the H. SPEED DUBB button in playback mode.
Then at HIGH speed mode.
5. Adjust RV652 on the AUDIO board do that frequency counter
reads 6,000 ± 60 Hz.
6. Take off the H. SPEED DUBB button.
Then at NORMAL speed mode.
7. Adjust RV651 on the AUDIO board so that frequency counter
30
reads 3,000 +– 10
Hz.
8. Frequency difference between deck A and deck B the beginning of the tape should be within ± 1.5%.
Adjustment Location: AUDIO board
Playback level Adjustment
Procedure:
Mode: Playback (FWD)
test tape
P-4-L300
(315 Hz, 0 dB)
DECK A
DECK B
level meter
set
+
–
main board
CN207 (Pin 1 : L-CH)
(Pin 3 : R-CH)
reverse
Deck A is RV311 (L-CH) and RV411 (R-CH), Deck B is RV301 (LCH) and RV401 (R-CH) so that adjustment within adjustment level
as follows.
Adjustment Level:
CN207 PB level: 301.5 to 338.3 mV (–8.2 to –7.2 dB) level
difference between the channels: within ±0.5 dB
Adjustment Location: AUDIO and main boards
forward
– 33 –
Record bias Current Adjustment
Procedure:
1. Mode: record
Adjustable limits:
CN207 PB level: 47.3 to 53.1 mV (–24.3 to –23.3 dB)
Adjustment Location: main board
DECK B
[MAIN BOARD] (Component Side)
Pin 6 (L-CH) of IC1501 on the main board.
Pin #¶ (L-CH) of IC1501 on the main board.
1) 315 Hz 
2) 10 kHz  50 mV (–23.8 dB)

AF OSC
blank tape
CN-123
600 Ω
attenuator
RV1501
IC1501
CN205
CN207
IC301
RV1551
IC201
set
RECORD LEVEL
Pin 2 (GND) of ICN207 on the main board.
2. Mode: Playback
recorded
portion
level meter
+
–
set
CN207 (Pin 1 : L-CH)
(Pin 3 : R-CH)
RECORD
BAIS
TAPE SPEED





[AUDIO BOARD] (Conductor Side)











PB LEVEL
Record Level Adjustment DECK B
Procedure:
1. Mode: record
– DECK B –
AF OSC
blank tape
CS-123
600 Ω
attenuator
set
Pin 2 (GND) of CN207 on the main board.
2. Mode: Playback
level meter
set
PB
LEVEL
(HIGH)
RV652
®
RV311
L ®
RV411
R®
– DECK A –
Pin 6 (L-CH) of IC1501 on the main board.
Pin #¶ (R-CH) of IC1501 on the main board.
315 Hz, 50 mV (–23.8 dB)
recorded
portion
(NORMAL)
RV651
®





L
R
RV301®L
RV401®R RV441 RV341





Confirm playback the signal recorded in step 1 become adjustable
limits as follows.
If these levels do not adjustable limits, adjustment the RV341 (L-CH)
and RV441 (R-CH) on the AUDIO board to repeat steps 1 and 2.
Adjustable limits: Playback output of 315 Hz to playback output
of 10kHz: 0±0.5 dB
Adjustment Location: AUDIO and main boards
+
–
CN207 (Pin 1 : L-CH)
(Pin 3 : R-CH)
Confirm playback the signal recorded in step 1 become adjustable
limits as follows.
If these levels do not adjustable limits, adjustment the RV1501 (LCH) and RV1551 (R-CH) on the main board to repeat steps 1 and 2.
– 34 –
TUNER SECTION
0dB=1µV
Note: As a front-end (FE1) is difficult to repair if faulty, replace it
with new one.
AM Section Adjustment
Setting:
loop antenna
(Supplied accessories)
loop antenna
AM RF SSG
set
30% amplitude
modulation by
400 Hz signal
AM ANTENNA
terminal (TM1)
60 cm
Field strength dB (µV/m) =SSG output level dB (µV/m) –26 dB.
AM Tuned Level Adjustment
Band: AM or MW
Procedure:
1. Set the output of SSG so that the input level of the set becomes
55 dB.
2. Tune the set to 1,050 kHz (US, CND models), 999 kHz (other
models).
3. Adjust RV41 (AEP, UK models), RV42 (other models) to the
point (moment) when the TUNED indicator will change from
going off to going on.
Adjustment Location:
AEP, UK model
[TCB BOARD] (Component Side)
IC41
RV41
RV42
TM1
Adjustment Location : TCB board
FM Section Adjustment
Note: This adjustment should be performed after the AM Tuned
Level Adjustment due to the same adjustment element.
Setting:
FM RF stereo signal
generator
75 Ω coaxial
FE1
Other model
[TCB BOARD] (Component Side)
IC2
set
Carrier frequency : 98 MHz
Modulation
: AUDIO 1 kH, 75 kHz
FM ANTENNA terminal
deviation (100%)
(TM1) (75 Ω open)
FM Tuned Level Adjustment
Band: FM
Procedure:
1. Supply a 25dBµ 98 MHz signal from the ANTENNA terminal.
2. Tune the set to 98 MHz.
3. If the TUNED indicator does not light, adjust RV42 (AEP, UK
models), RV41 (other models) to the point (moment) when the
TUNED indicator will change from going off to going on.
Adjustment Location: TCB board
RV42
RV41
TM1
FE1
• Abbreviation
CND: Canadian model
– 35 –
S Curve Check
CD SECTION
Note:
1. CD Block is basically designed to operate without adjustment.
Therefore, check each item in order given.
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.
3. Use an oscilloscope with more than 10M impedance.
4. Clean the object lens by an applicator with neutral detergent
when the signal level is low than specified value with the following checks.
5. Adjust the focus bias adjustment when optical block is replaced.
Focus Bias check
oscilloscope
BD board
TP (FEO)
TP (VC)
+
–
oscilloscope
BD board
TP (FEO)
TP (VC)
+
–
Procedure:
1. Connect oscilloscope to test point TP (FEO).
2. Connect between test point TP (FOK) and GND by lead wire.
3. Turn Power switch on.
4. Put disc (YEDS-18) in and turned Power switch on again and
actuate the focus search. (actuate the focus search when disc
table is moving in and out.)
5. Check the oscilloscope waveform (S-curve) is symmetrical between A and B. And confirm peak to peak level within 3±1 Vp-p.
S-curve waveform
symmetry
Procedure:
1. Connect oscilloscope to test point TP (RF). (GND terminal :
VC)
2. Turned Power switch on.
3. Put disc (YEDS-18) in and playback.
4. Confirm that the shape “≈” can be clearly distinguished at the
center of the waveform and check the RF signal level.
• RF signal
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
A
within 3 ± 1 Vp-p
B
6. After check, remove the lead wire connected in step 2.
Note: • Try to measure several times to make sure than the ratio of
A : B or B : A is more than 10 : 7.
• Take sweep time as long as possible and light up the brightness to obtain best waveform.
RF Level Check
oscilloscope
level:
1.3 ± 0.3Vp-p
BD board
TP (RF)
TP (VC)
+
–
Procedure:
1. Connect oscilloscope to test point TP (RF) on BD board.
2. Turned Power switch on.
3. Put disc (YEDS-18) in and playback.
4. Confirm that oscilloscope waveform is clear and check RF signal level is correct or not.
Note:
Clear RF signal waveform means that the shape “≈” can be
clearly distinguished at the center of the waveform.
• RF signal
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
level:
1.3 ± 0.3Vp-p
– 36 –
Adjustment Location:
E-F Balance (1 Track Jump) check
(Without remote commander)
[BD BOARD] (Conductor Side)
oscilloscope
BD board
VC
+
–
Procedure:
1. Connect oscilloscope to test point TP (TEO) on BD board.
2. Turned Power switch on.
3. Put disc (YEDS-18) in to play the number five track.
4. Press the “P (Pause)” button. (Becomes the 1 track jump mode)
5. Check the level B of the oscilloscope's waveform and the A (DC
voltage) of the center of the Traverse waveform.
Confirm the following:
FOK
CNU101
TP (TEO)
TP (VC)
RF
IC101
TEO
FEO
GND
IC103
A–B
× 100 = ±7 (%)
2 (A + B)
1 track jump waveform
IC
I02
GND
Center of the waveform
B
CNU102
A (DC voltage)
0V
symmetry
level : 500 mV ± 100 mVp-p
– 37 –
SECTION 6
DIAGRAMS
• Circuit Board Location
TRANS board
TCB board
PANEL board
MAIN board
HEADPHONE-MIC
board
TC-A SW
board
POWER AMP
board
LED board
CD-A SW board
TC-B SW board
CD-B1 SW board
DOOR SW board
CD-B2 SW board
MOTOR board
LEAF SWITCH
board
CD MOTOR board
BD board
AUDIO board
BD LED board
– 38 –
• Waveforms
— BD Section—
1 IC101 #£ pin (PLAY MODE)
6 IC103 ^™ pin (RFCK)
!¡ IC301 !£ pin (XT2)
Approx. 1.3 Vp-p
4.6 Vp-p
31.3 µsec
2 IC101 2 pin (FEI) (PLAY MODE)
7 IC103 &¢ pin (WFCK)
— TUNER Section—
!™ IC1 @¢ pin (XOUT) (EXCEPT AEP, UK)
IC21 @¢ pin (X OUT) (AEP, UK)
5.6 V
Approx. 0.1 V
4.8 Vp-p
135.5 µsec
3 IC101 $¶ pin (TEI) (PLAY MODE)
8 IC103 *ª pin (XTAI)
222 nsec
Approx. 0.2 V
10 V
!£ IC2 @£ pin (VCO) (EXCEPT AEP, UK)
IC41 @£ pin (VCO) (AEP, UK)
4.8 Vp-p
59.8 nsec
4 IC103 @¶ pin (MDP)
— PANEL Section—
9 IC601 8 pin (X-OUT)
2.4 V
2.2 nsec
2.1 V
7.8 µsec
125 nsec
5 IC103 ^º pin (XPCK)
— MAIN Section—
0 IC301 0 pin (X2)
7V
5.7 V
230 nsec
200 nsec
– 39 –
HCD-D290/G3300/XB3
6-1. BLOCK DIAGRAMS
– TUNER SECTION – (US, CND, E, AR, MX, AUS, PX MODELS)
ST +10V
Q5
FE1
FM FRONT END
TM1
ANTENNA
FM 75Ω
IF OUT
F OUT
VT
ANT IN
CF2
IF AMP 10.7MHz
Q3,4
IF AMP
Q1,2
1
L 16
22 MPX IN
AM / FM 24
CF1
10.7MHz
OUT L 20
LPF
OUT R 21
RCH
18 AMP IN L
FM IN
AM
FM / AM MPX
IC2
A
MAIN SECTION
(page 43)
ST LED 8
4 REG
TU LED 7
AM MIX 2
STEREO
70
TUNED
69
5 AM IF
AM IF
IFT41
AM
SD 12
FE2
AM FRONTEND
RV42
AM
TUNING
LEVEL
7
B+
F OUT 9
29 AM OSC
RF OUT 13
27 AM RF IN
3 ANT IN
AM / FM
VCO STOP
IF BUFF
MUTE
FM SD
VT
14
X42
10.7MHz
9 DET
30
14 15 11
AM
SD 13
X43
450KHz
23 VCO
X41
456KHz
RV41
FM
TUNING
LEVEL
MUTE
72
B
MAIN
SECTION
(page 44)
FM OSC
PD1
AM OSC
FM
PLL
IC1
1 24
X IN
7 2 12 8
X OUT
14
IF REQ
15 19
VCO STOP
IF
10
FM
X21
4.5MHz
CE 3
DI 4
CL 5
DO 6
ST-CE
68
COM-DIN
67
COM-CLK
65
COM-DATA
66
• R CH:Same as L CH
• SIGNAL PATH
:FM
:AM
• Abbreviation
CND :Canadian model
AUS :Australian model
:Argentine model
AR
:Mexican model
MX
– 40 –
HCD-D290/G3300/XB3
– TUNER SECTION – (AEP, UK MODELS)
ST +10V
FE1
FM FRONT END
CF1
10.7MHz
IF OUT
F OUT
VT
ANT IN
22 MPX IN
OUT R 21
AM / FM 24
CF2
CF3
IF AMP 10.7MHz IF AMP 10.7MHz
Q1,2
Q3,4
1
18 AMP IN L
L 16
LPF
OUT L 20
Q5
TM1
ANTENNA
FM 75Ω
COAXIAL
RCH
FM IN
AM
FM / AM MPX
IC41
A
MAIN SECTION
(page 43)
FE2
MW / LW FRONTEND
6
12
5
13
3
14
15
16
2
LW SW
Q9
22
70
TUNED
69
5 AM IF
AM
SD 12
RV41
AM
TUNING
LEVEL
29 AM OSC
X41
10.7MHz
9 DET
21 20
FM SD
AM / FM
Q11
MW SW
VCO STOP
IF BUFF
MUTE
27 AM RF IN
Q12
MW SW
STEREO
AM IF
IFT1
Q14
LW SW
Q13
MW SW
TU LED 7
AM MIX 2
17
26 25 24 23
ST LED 8
4 REG
30
14 15 11
AM
SD 13
X42
450KHz
23 VCO
X43
456KHz
RV42
FM
TUNING
LEVEL
MUTE
72
FM OSC
PD1
MW
AM OSC
FM
PLL
IC21
1 24
X IN
7 2 12 8
X OUT
14
IF REQ
11
VCO STOP
FM / AM IF
15 19 9
MW
10
FM
X21
4.5MHz
CE 3
DI 4
CL 5
DO 6
ST-CE
68
COM-DIN
67
COM-CLK
65
COM-DATA
66
• R CH :Same as L CH
• SIGNAL PATH
:FM
:MW
:LW
– 41 –
B
MAIN
SECTION
(page 44)
HCD-D290/G3300/XB3
– CD SECTION –
OPTICAL PICK-UP BLOCK
89
E
F
FE-O 6
FE-M 7
21
27
75 100 12 11 10 9 8 7
TA-M 12
TA-O 13
36 LD
37 PD
LASER
DIODE
S101
LIMIT SWITCH
73
SENS2 26
R-CH
MAIN
C SECTION
(page 44)
XRST
Q101
LD DRIVE
LOUT2 93
MAIN
E SECTION
(page 43)
DATA
SENS
SQSQ
SQCK
42 E
B
CLOCK
XLAT
41 F
6
IC103
DIGITAL SIGNAL
PROCESSOR
XRST
C
LOUT1 86
14 CNIN
13 SEIN
23 FOK
15 DATAO
16 XLTO
17 CLKO
29 LOCK
SCOR
C
39
57
B
D
24
25
27
22
21
20
19
18
D
44 RF
RFO 33
C,OUT
SENS1
FOK
DATA
XLT
CLK
LOCK
SPOD
A
38 PD1
PD2
4
2
5
10
MDP
1
A
90
58
47
74
34
36
B+
K
48
DETECTOR
X101
16.9344MHz
IC101
FOCUS/TRACKING
/SLED/SERVO
RF AMP
23
FOCUS
COIL
TRACKING
COIL
9
T-
MUTE
15
16
FF+
27
FOCUS / TRAKING
COIL DRIVE
IC102 (1 / 2 )
T+
2-AXIS
DEVICE
TRACKING
COIL DRIVE
18
17
FOCUS
COIL DRIVE
SLED / SPINDLE
MOTOR DRIVE
IC102 (2 / 2)
26
SLED
SERVO
IC101 (2 / 2)
M102
SLED MOTOR
M
12
.
11
SLED MOTOR
DRIVE
6
M101
SPINDLE MOTOR
M
14
.
13
SPINDLE MOTOR
DRIVE
3
16 SLO
SL-P 14
S201
UP SWITCH
M201
TABLE MOTOR
M
77
IC202
DISC TABLE
SENSOR
76
Q201
SWITCH
62
3 IC201 1
MOTOR
9
7
DRIVE
61
– 42 –
MAIN
D SECTION
(page 44)
• R CH:Same as L CH
• SIGNAL PATH
60
:CD
HCD-D290/G3300/XB3
– MAIN SECTION –
IC231
SPEANA MIX
2
+
1
–
3
J761
MIC
IC101
PHONO
AMP
IC102 INPUT SELECTOR
3
A
28
B
29
C
30
11
12
VIDEO (AUDIO)
R-CH
13
69
71
R-CH
65
+
–
45
+
42
Q204
MUTE
IC201
EQUALIZER/VOLUME
62
32 33 34
40
41
R-CH
Q801
OVER LOAD
DET
+
–
MUTE
+
R-CH
R-CH
D590
+
Q283
MUTE
Q232
SWITCH
Q203
FEED BACK
R-CH
R-CH
Q851
OVER LOAD
DET
Q231
SWITCH
TM131
SPEAKER
-
Q282
OVER LOAD
DET
L-CH
TM132
-
Q141,Q142
RELAY DRIVE
SORROUND
-
2
44
3
Q202
DBFB SWITCH
45
+
–
38
L-CH
-
RY141
43
44
EQ
MICON
INTERFACE
A
10
B
9
C
6
4
5
2
64
BB12
TUNER SECTION A
(page 40,41)
J101 (2 / 2)
14
J760
PHONES
*1 IC801
POWER AMP
15
CD SECTION E
(page 42)
R-CH
BB22
J101 (1 / 2)
PHONO
IC760 (1 / 2) RV706
IC760 (2 / 2)
MIC AMP MIC LEVEL MIC AMP
+
R-CH
IC611
65
66
67
68
69
70
72
XT1
POWER
RESET
AC CUT
F-RELAY
XT2
TA MUTE
X1
27
46
10
11
13
14
98
15
20
Q1001
REEL
DET
Q1002
Q901
REEL
Q902
DET
SWITCH
X302
32.768KHz
Q301
SWITCH
Q901
Q902
SWITCH
IC302
RESET
Q905
Q906
SWITCH
89
90
91
92
93
79-80 • 1-6 • 14-19
LED
25 LED SELECT
SELECT SWITCH
Q601-Q603
23 CLOCK
24 DATA
94
95
S1002
B PLAY
S1004
(A HALF)
97
S1007
(B HALF)
28
S1009
(REC B)
88
87
83
84
JOG
S711
27 - 30
KEY1-KEY4
22 • 35
JOG A•B
IC601
DISPLAY CONTROL
21
20
SEG1-SEG20
42- 56
57- 77
8
9
32
36 37
33
10
FL601
VF
VF
+5V
+7V
-7V
D671-D674
– 43 –
34
GR1-GR15
IC602
SIRCS
BACK LIGHT
+35V
FRUORESCENT INDICATOR TUBE
X601
8MHz
-35V
+5V
EXCEPT US,CND
D901
RECT
1
ROTARY
ENCODER
S701
RESET
85
S601-S626,S628-S631
S641-S647,S651-S659
S661-S668,S676-S679
SIRCS
Q1534,Q1535
SWITCH
D611-D625
D631,D632
D635-D638
D641
D645-D647
S691
DOOR SW
+7V
-7V
IC901
REG
CD MOTOR +7V
IC902
REG
DOOR SW
4
5
61
S1001
A PLAY
S1006
(REC A)
STK MUTE
X2
26
X301
5MHz
VOLUME
Q604-Q608
Q609-Q611
Q614
Q617-Q619
Q621
SPEANA1
SPEANA2
IC1502
TRIGGER
MOTOR
10 DRIVE
2
M
Q1533
SWITCH
82
L+R
M2
TRIGGER
MOTOR
LED DRIVE
Q651
CAPSTAN MOTOR
CONTROL
RV651
NORMAL SPEED
11C-DATA
11C-CLK
CD-POWER
ST-CLK
ST-DIN
ST-DOUT
ST-CE
TUNED
STEREO
ST MUTE
B-SHUT
28
55
56
RV652
HIGH SPEED
X IN
B+
(+12V)
1
*1
X OUT
M
6
100
97
Q907
SWITCH
96
M1
CAPSTAN
MOTOR
86
55 56
A-SHUT
427LAT
COM DOUT
COM CLK
65 66 67 68 69 70 72
B HALF
44 45
S1008
B CrO2
Q1531,Q1532
CAPSTAN MOTOR
SWITCH
TUNER
SECTION
A HALF
A-PLAY-SW
B-PLAY-SW
94 95
(page 42)
55
56
3
44
45
96
92
93
REALY
TC-MUTE
PB A/B
EQ-H/N
BIAS
REC-MUTE
NR ON/OFF
R/P-PASS
DBFB H/L
86 85 84 83 82
3
28
CD
SECTION
D
12 13 14 15 16 17 18 19 20
S1005
A CrO2
62 61 60
97
22
77 76
94
95
BIAS
SW
CROM
87
88
89
90
91
2
+7V
NORM
A-TRG
CAP-H/N
25
24
Q623
SWITCH
87 88 89 90 91 92 93 96
IC301
MAIN CONTROL
B-TRG
PB A/B
A120/170
NORM/HIGH
NORM/CROM/METAL
BIAS ON/OFF
RM ON/OFF
NR ON/OFF
REC/PB/PASS
T621
2
SENS2
SENS
REC
EQ
11
73 74
86
85
84
83
BIAS
TRAP
Q621,622
BIAS OSC
18 34 36 47 48 57 58
CAP-M-ON/OFF
TRG-LOW
C331,L331
82
REC R-CH
(page 40, 41) B
73
74
PB R-CH
37
58
35
TRAY-LED
TBL-R
TBL-L
3
RV341
REC BIAS
X
TA AC OFF
62
61
60
ERASE
(HEAD)
IC1501
HEAD AMP
DECK PROCES
10
4
CD
SECTION (page 42)
C
9
18
34
36
47
48
57
RV105
REC LEVEL
2
R-CH
<PB L-CH>
SCOR
SQ-DATA-IN
SQCLK
CD DATA
CD CLOCK
XRST
XLT
IC602
PB / REC SW
R-CH
8
PAS
RV301
PB LEVEL
1
REC/PB HEAD
(B DECK)
<REC L-CH>
4
PBEQ
7
AMP
HRPE101
PB
6
PB
7
UP SW
T-SENS
5
REC
DOL
DOLBY
B
120
IC601
R-CH
70
2
77
76
HP101
PLAYBACK HEAD
(A DECK)
REC
PBEQ
1
AMP
LM ON/OFF
3
Q281
SWITCH
1
4
IC281
PROTECTOR
6
R-CH
2
RV311
REC LEVEL
ST +10V
+5V
IC903
REG
Q903
REG
IC904
REG
VP
Q904
REG
TC MOTOR
+12V
T901
POWER TRANSFORMER
D902
|
D905
RECT
2
AC -IN
17
18
+
–
10
+
–
13
US,CND
3
4
19
20
6
D906
D907
RECT
S901
VOLTAGE
SELECTOR
E,AR,PX
VF
• R CH:Same as L CH
• SIGNAL PATH
:FM
:PB (DECK B)
:REC (DECK B)
MID FREQ
:CD
LOW FREQ
• Abbreviation
:Argentine model
AR
HIGH FREQ
– 44 –
12
+
–
15
8
:PB (DECK A)
TA AC OFF
+
–
• IC Block Diagrams –BD Section –
CC2
FOK
31
30
29
28
27
27
26
25
24
23
22
21
OUT4B
CC1
32
OUT4A
CB
33
OUT3B
OP IN (–)
CP
34
OUT3A
OP OUT
RF_I
35
VCC
IN3A
RF_O
36
19
18
17
16
15
NC
IN3B
RF_M
PD
37
RFTC
PD1
38
LD
PD2
39
GND
IN4A
28
IC101 CXA1992AR
OP IN (+)
IN4B
IC102 BA5941FP
20
NC
VEE
– +
Vcc
–
+
+
–
26 SENS2
+
–
–
+
LASER POWER CONTROL
F IV AMP
VCC
VCC
FE AMP
IFB1-6
BAL1-4
TOG1-4
FS1-4
TG1-2
TM1-7
PS1-4
17 ISET
ISET
– +
+ –
11
12
13
14
OUT1A
OUT1B
LRCKI
PCMD
PCMDI
OUT2B
BCK
BCKI
VSS
VDD
OUT2A
GTOP
XUGF
VCC
XPCK
GFS
RFCK
MUTE
C2PO
XROF
GND
MNT3
MNT1
XTSL
GND
FSTT
C4M
IN2A
DOUT
EMPH
EMPHI
IN2B
WFCK
SCOR
IN1A
SBSO
8
7
MNT0
6
5
EXCK
IN1B
IC103 CXD2519Q
VSS
3
NC 81
50 LRCK
49 WDCK
AVDD 83
AIN1 85
TM6
LOUT1 86
–
+
15 SL_M
VCC
VEE
FOCUS
PHASE COMPENSATION
TM7
TM5
TM3
VEE
VEE
FS2
–
+
Charge
up
AVSS 87
XTAI 89
+
–
+
–
DFCT
–
+
XVDD 88
FS1
FZC COMP.
47 ASYO
–
+
14 SL_P
TM2
XTAO 90
XVSS 91
AVSS 92
FSET
TG2
–
+
–
+
ASYMMETRY
CORRECTOR
3RD-ORDER NOISE SHAPER
TM4
48 ASYE
AOUT1 84
PWM
16 SL_O
TRACKING
PHASE COMPENSATION
TG1
VCC
PWM
VCC
44 RF
43 AVDD
D/A
INTERFACE
EFM
DEMODURATOR
42 CLTV
DIGITAL
PLL
39 FILO
DIGITAL OUT
16K RAM
38 PCO
+
–
AIN2 94
13
TA_O
12
TA_M
11
FSET
10
TG2
9
TGU
8
SRCH
7
FE_M
OSC
AOUT2 95
AVDD 96
AVSS 97
35 VCKI
SUB CODE
PROCESSOR
OVER SAMPLING
DIGITAL FILTER
CLOCK
GENERATOR
NC 98
34 VPCO1
33 VPCO2
TIMING
LOGIC
NC 99
PWMI
MDS
LOCK
MDP
MON
VSS
VDD
FOK
XLON
DATA
SPOD
SENS
SPOC
SQSO
– 86 –
SPOB
SQCK
CLKO
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
SPOA
9
XLTO
8
DATO
7
SEIN
6
CNIN
5
XLAT
4
CLOK
3
CKOUT
31 TES0
TES2
2
DIGITAL CLV
LMUT
1
32 TES1
SERVO
AUTO
SEQUENCER
CPU
INTERFACE
RMUT
XRST 100
– 85 –
37 VCTL
36 V16M
SERIAL-IN
INTERFACE
VSS
6
FE_O
5
FLB
4
FGD
3
FDFCT
FEI
2
41 AVSS
40 FILI
VEE
1
46 ASYI
45 BIAS
ERROR
CORRECTOR
LOUT2 93
FS4
FEO
FZC 52
10
+ –
AVSS 82
TM1
TDFCT 50
VCC
9
– +
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
VCC
VC 51
2
VDD
CC1
DFCT1
MIRR
TGFL
DFCTO
DFCT
Vcc
18 VCC
VCC
–
+
TZC COMP.
19 LOCK
4
1
VDD
TZC 49
20 CLK
IIL DATA REGISTER
INPUT SHIFT REGISTER
ADDRESS DECODER
SENS SELECTOR
OUTPUT DECODER
ATSC
WINDOW
COMP.
MUTE
21 XLT
SYSM
–
+
–
+
LPC
FOH
FOL
TGH
TGL
BALH
BALL
ATSC
TZC
FZC
TEI 47
ATSC 48
LPCL
+
–
LDON
+
–
TTL
↓
IIL
FOK
TRK. GAIN
WINDOW COMP.
+
–
E-F BALANCE
WINDOW COMP.
Vcc
IIL
↓
TTL
MIRR
BIAS IN
–
+
IFB5
IFB6
IFB4
IFB3
IFB2
IFB1
TGFL
BAL4
BAL1
BAL2
BAL3
TOG4
TOG3
TOG2
TOG1
LPFI 46
VCC
+
–
+
–
+
–
+
–
–
+
TEO 45
23 XRST
VEE
22 DATA
FO. BIAS
WINDOW
COMP.
+
–
DFCT
LEVEL SHIFT
+
–
VEE
VEE
LEVEL S
LEVEL SHIFT
+
–
+
–
+
–
+
–
VEE
+
–
–
+
EI 43
VEE
LEVEL SHIFT
+
–
24 C. OUT
–
+
–
+
E IV AMP
LEVEL SHIFT
–
+
–
+
–
+
VCC
–
+
25 SENS1
VCC
–
+
E 42
VEE 44
IIL
↓
TTL
VEE
F 41
+
–
APC
+
–
VCC
+ –
–
+
FE_BIAS 40
+ –
+ –
+
–
–
+
RF SUMMING
AMP
–
+
PD1 IV
AMP
+ –
–
+
–
+
PD2 IV
AMP
AIN2
PD2
PD1
AIN1
AOUT1
VDD
FMIN
AMIN
IO2
24 23 22
21
20
19
18
17
16
15
14
13
VSS
XOUT
AOUT2
– TUNER Section –
IC1 IC21 LC72130
PHASE DETECTOR
CHARGE PUMP
UNLOCK
DETECTOR
POWER
ON
RESET
1/2
SWALLOW COUNTER
1/16, 1/17 4BITS
REFERENCE
DIVIDER
12BITS PROGRAMMABLE
DRIVER
9
10
11
IO1
CE
D1
CL
D0
8
BO4
XIN
BO5
7
BO3
3 4 5 6
BO2
2
BO1
1
12
FM-AFC
AM-RF-IN
AGC
AM. CUT
AM/FM
VCO
MPX-IN
OUT R
OUT L
AMP-IN R
AMP-IN L
R
30
29
28
27
26
25
24
23
22
21
20
19
18
17 16
ALC
AM
OSC
AM
RF. AMP
AM
MIX
DECODER
ANTI BIRDIE
BUFF
STEREO
SW
AGC
STEREO
DRIVE
S METER
FM
IF
FF
FF
VCO
AM/FM
IF
BUFF
TUNING
DRIVE AM
FM
1
2 3
4
5
6
7
8
9
10
11
AM-MIX
IF
REG
AM-IF
GND
TU-LED
ST-LED
DET
VCC
IF-BUFF
VCC
FM-IN
GND
12
13
14
15
VCO-STOP
REG
PHASE
DET
AM/FM
FM
DET
MUTE
PILOT
DET
COMP
AM/FM
SW
TRIG
FF
AM. SD
FM
IF
S-CURVE
AM
DET
AM. SD
LEVEL
DET
L
AM-OSC
IC41 LA1835
FM-SD
IC2
UNIVERSAL
COUNTER
DATA SHIFT REGISTER LATCH
IFIN
C2B
I/F
– 87 –
6-18.
IC PIN FUNCTION DESCRIPTION
MAIN BOARD IC301 µPD780018Y (MAIN CONTROL)
Pin No.
Pin Name
I/O
1
TA-MUTE
O
Line mute signal output
2
DBFB-H/L
O
DBFB H/L select signal output
3
427-LT
O
Latch signal output for IC201 (62427)
4
KCON-LT
O
5
KCON-ON/OFF
O
6
F-RELAY
O
7
R-RELAY
O
8
PL-RELAY
O
9
TEST
I
10
X2
O
11
X1
I
12
VDD
–
13
XT2
O
14
XT1
I
15
RESET
I
16
INT/IN
I
17
INT/IN/OUT
I
Function
Not used
Front speaker relay control output
Not used
Connected ground
X’tal (5MHz)
Power supply (+5V)
X’tal (32.768 KHz)
Reset signal input
Connected ground
18
SCOR
O
Subcode data request signal output
19
SOFT-TEST
O
Software test port
20
AC-CUT
I
Back up signal input
21
RDS-INT
I
22
RDS-DATA
I
23
VDD
–
Power supply (+5V)
24
AVDD
I
Analog reference voltage input
25
ADJ
I
CD adjust point port
26
A-SHUT
I
A Deck reel pulse detector
27
B-SHUT
I
B Deck reel pulse detector
28
B-HALF
I
Half detector signal input
29
CLK-CHECK
I
Connected ground
30
SPEC-IN
I
Version select signal input
Not used
31
ADJ 2
I
Connected ground
32
DEMO-CHANGE
I
DEMO H/L select signal input
33
AVss
–
Ground
34
SQ-DATA-IN
I
Subcode Q data input
35
—
–
Not used
36
SQ-CLK
O
Sub code Q data clock input
37
SW-ON/OFF
O
Not used
38, 39
FUNC 1, 2
I
Connected ground
40
Vss
–
Ground
41
VOL-LAT
O
42
PL-LAT
O
Not used
43
COM-DIN
I
Connected ground
44
COM-DOUT
O
Common serial data output
– 88 –
Pin No.
Pin Name
I/O
45
COM-CLK
O
Common serial clock output
Function
46
CD-POWER
O
CD power on signal output
47
CD-DATA
O
CD data output
48
CD-CLOK
O
CD clock output
49
MSM-CMD
O
Not used
50
MSM-BUSY
I
Connected ground
51
MSM-LT
O
52
MSM-NAR
I
Not used
53
MSM-CH
O
54
INPUT-CHANGE
O
55
11C-DATA
O
Data output for IC601
56
11C-CLK
O
Clock output for IC601
57
XRST
O
CD reset signal output
58
XLT
O
CD latch signal output
59
FOUCUS-SW
O
Not used
60
TBL-L
O
61
TBL-R
O
62
TRAY-LED
O
63
LOAD-OUT
O
64
LOAD-IN
O
65
ST-CLK
O
Tuner clock output
66
ST-DIN
I
Tuner data input
67
ST-DOUT
O
Tuner data output
68
ST-CE
O
Tuner chip enable output
69
TUNED
I
Tuned detection for tuner
70
STEREO
I
Stereo detection for tuner
71
Vss
–
Ground
72
ST-MUTE
O
Tuner mute signal output
73
SENS2
I
74
SENS
I
75
DISC-SENS
I
Not used
76
T-SENS
I
CD table detection signal input
77
UP-SW
I
Up SW (S201) signal input
78
ENC 3
I
Not used
Table motor control output
CD tray LED ON/OFF output
Not used
BD Condition signal input
79
ENC 2
I
80
ENC 1
I
Not used
81
OUT-OPEN
I
82
CAP-M-H/N
O
Capstan motor H/N speed select signal output
83
B-TRG
O
Trigger motor control output
84
A-TRG
O
Trigger motor control output
85
TRG-LOW
O
Trigger motor control output
86
CAP-M-ON/OFF
O
Capstan motor ON/OFF signal output
87
PB-A/B
O
PB Deck A/Deck B select output
Not used
– 89 –
Pin No.
Pin Name
I/O
88
EQ-H/N
O
Function
Equalizer H/N select output
89
BIAS
O
Bias ON/OFF signal output
90
REC-MUTE
O
REC mute ON/OFF selection output
91
NR-ON/OFF
O
NR ON/OFF signal output
92
R/P-PASS
I
REC/PB/PASS selection output
93
TC-MUTE
O
TC mute ON/OFF selection output
94
A-PLAY-SW
I
Deck A play detect
95
B-PLAY-SW
I
Deck B play detect
96
TC-RELAY
O
REC/PB head selection output for IC602
97
A-HALF
I
Deck A cassette detect
98
POWER
O
POWER ON/OFF signal output
99
SW-F-CHG
O
Super woofer mode signal output Not used
100
STK-MUTE
O
Power amp ON/OFF signal output
– 90 –
PANEL BOARD IC601 TMP87CH74 (DISPLAY CONTROL)
Pin No.
Pin Name
I/O
1-6
LED3-LED8
O
LED driver output
Function
Ground
7
VSS
–
8
X-OUT
O
9
X-IN
I
10
RESET
I
11
LED 9
O
12
LED10
O
13
TEST
I
14-19
LED11-LED19
O
LED driver output
20
VOL-A
I
Rotary encoder (S701 VOLUME) pulse input
21
DOOR SW
I
SOOR SW (S651) ON/OFF signal input
X’tall (8MHz)
Reset signal input from main controller
Connected ground
22
JOG-A
I
Rotaly encoder (S711 AMS) pulse input
23
CLOCK
I
Serial clock input from main controller
24
DATA
I
Serial data input from main controller
25
LED SELECT
O
LED select signal output
26
MODEL
I
Version select signal input
27-30
KEY1-KEY4
I
Key input
31
SPEANA-3
I
Connected ground
32
L+R
I
Spectrum analyzer (high frequency) input
33
SIRCS
I
Remote commander signal input
34
VOL-B
I
Rotary encoder (S701 VOLUME) pulse input
35
JOG-B
I
Rotary encoder (S711 AMS) pulse input
36
SPEANA-1
I
Spectrum analyzer (Low frequency) input
37
SPEANA-2
I
Spectrum analyzer (Middle frequency) input
38
VASS
–
Ground
39
VAREF
I
Analog reference voltage input
40
VDD
–
Power supply (+5V)
41
—
–
Not used
42-56
GR1-GR15
O
FL gride signal output
57-77
SEG1-SEG77
O
FL segment signal output
78
VKK
–
–30V driving power for FL
79, 80
LED1-LED2
O
LED driver output
– 91 –
SECTION 7
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Color Indication of Appearrance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
• Abbreviation
AR: Aurzenchin EE: East European
AUS: Australian MX: Mexican
CND: Canadian
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of the
electrical parts list.
(1) CASE, REAR PANEL SECTION
The components identified by mark
! or dotted line with mark ! are
critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque ! sont critiquens pour la
sécurité.
Ne les remplacer que par une pièce
portant le neméro spécifié.
#2
2
#2
UK, AUS
4
3
1
#3
#2
1
#1
#1
6
5
#1
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
PANEL, BACK (XB3: PX)
PANEL, BACK (XB3: MX)
BAND, PLUG FIXED (UK, AUS)
TCB BOARD, COMPLETE (US, CND)
TCB BOARD, COMPLETE (E, AR, MX, AUS, PX)
*
*
*
*
1
2
2
3
3
4-929-973-01
4-987-052-11
4-987-052-51
4-987-043-01
4-987-043-11
SCREW (CASE, 3 POINT)
CASE (D290/ XB3)
CASE (G3300)
PANEL, BACK (D290: US)
PANEL, BACK (D290: CND)
* 3
* 3
4
* 5
* 5
4-987-134-21
4-987-134-31
4-956-370-12
A-4303-510-A
A-4303-512-A
*
*
*
*
*
3
3
3
3
3
4-987-043-21
4-987-043-31
4-987-043-41
4-987-043-61
4-987-134-01
PANEL, BACK (G3300: US)
PANEL, BACK (G3300: CND)
PANEL, BACK (XB3: AEP, UK)
PANEL, BACK (XB3: EE)
PANEL, BACK (XB3: E, AR)
* 5
* 5
6
A-4303-570-A TCB BOARD, COMPLETE (EE)
A-4303-576-A TCB BOARD, COMPLETE (AEP, UK)
1-769-974-11 WIRE (FLAT TYPE) (13 CORE)
(EXCEPT AEP, EE, UK)
1-773-006-11 WIRE (FLAT TYPE) (15 CORE) (AEP, EE, UK)
* 3
6
4-987-134-11 PANEL, BACK (XB3: AUS)
– 92 –
(2) FRONT PANEL SECTION-1
58
TCM-220WR2
57
73
59
61
57
57
57
60
57
55
62
not
supplied
#1
62
56
65
57
66
54
not
supplied
64
67
57
63
57
57
75
53
70
74
68
supplied
with S711
57
71
52
69
51
72
57
Ref. No.
Part No.
Description
SPRING (CD EJECT), COMPRESSION
BUTTON (EJECT CD)
CD-A SW BOARD
PANEL (A) SUB ASSY (D290)
PANEL (A) SUB ASSY (G3300)
* 63
64
64
* 65
66
* 67
1-664-016-11
4-987-038-11
4-987-038-01
4-987-933-01
4-987-000-01
1-664-013-11
DOOR SW BOARD
LID, DISC (G3300)
LID, DISC (D290/ XB3)
BRACKET (TA)
BUTTON (EJECT B)
TC-B SW BOARD
X-4948-348-1
1-664-012-11
4-986-999-01
4-951-620-01
1-773-161-11
PANEL (A) SUB ASSY (XB3)
TC-A SW BOARD
BUTTON (EJECT A)
SCREW (2.6X8), +BVTP
WIRE (FLAT TYPE) (21 CORE)
* 68
69
70
71
71
1-664-010-11
X-4947-969-1
4-987-037-01
X-4948-296-1
X-4948-298-1
CD-B1 SW BOARD
BUTTON (CD STOP) ASSY
KNOB (JOG)
PANEL (B) SUB ASSY (D290/ XB3)
PANEL (B) SUB ASSY (G3300)
1-769-949-11
3-354-963-01
1-664-017-11
4-957-577-01
WIRE (FLAT TYPE) (11 CORE)
DAMPER
LED BOARD
SCREW PTP WH (2.6X8) (DIA. 10)
* 72
73
73
74
1-664-011-11
A-4384-396-A
A-4384-446-A
4-987-014-01
CD-B2 SW BOARD
LID ASSY, CD (D290/ XB3)
LID ASSY, CD (D3300)
INDICATOR (CD)
Ref. No.
Part No.
Description
51
52
* 53
54
54
4-987-995-01
4-987-001-01
1-664-009-11
X-4948-295-1
X-4948-297-1
54
* 55
56
57
58
59
60
* 61
62
Remark
– 93 –
Remark
(3) FRONT PANEL SECTION-2
Supplied with Supplied with
RV760
J761
not
supplied
110
110
111
119
112
109
supplied with
J760
114
118
108
117
106
120
107
110
116
113
115
105
121
122
123
104
124
125
126
supplied
with S701
not supplied
not
supplied
126
110
not supplied
102
103
127
101
Ref. No.
Ref. No.
Part No.
Description
BUTTON (CD, PLAY)
PANEL ASSY, FRONT (D290)
PANEL ASSY, FRONT (XB3)
PANEL ASSY, FRONT (G3300)
KNOB (VOL)
LID ASSY, CASSETTE (D290/ XB3)
112
113
114
115
116
* 117
4-986-986-01
4-987-012-01
X-4947-964-1
4-986-990-01
4-978-683-01
4-987-041-01
BUTTON (POWER)
INDICATOR (TA)
BUTTON (SOUND) ASSY
BUTTON (CURSOR)
SPRING, COMPRESSION
COVER, CURSOR
X-4947-973-1
4-987-032-01
4-987-028-01
4-987-021-01
4-986-997-01
LID ASSY, CASSETTE (G3300)
DISPLAY (TA)
DISPLAY (ST)
INDICATOR (TC A)
BUTTON (DECK.A)
118
* 119
120
121
122
X-4947-963-1
A-4392-444-A
1-773-051-11
X-4947-962-1
4-987-013-01
BUTTON (FUNCTION) ASSY
PANEL BOARD, COMPLETE
WIRE (FLAT TYPE) (17 CORE)
BUTTON (TUNER) ASSY
INDICATOR (TUNER)
4-963-404-21
4-973-644-01
4-951-620-01
A-4392-452-A
EMBLEM (5-A), SONY
KNOB (MIC)
SCREW (2.6X8), +BVTP
HEADPHONE-MIC BOARD, COMPLETE
123
124
125
126
4-986-992-01
X-4947-967-1
4-987-022-01
4-987-996-01
BUTTON (DBFB)
BUTTON (DECK B) ASSY
INDICATOR (TC B)
SPRING (TC LID), TENSION
Part No.
Description
75
101
101
101
102
103
4-987-002-01
A-4384-393-A
A-4384-394-A
A-4384-395-A
4-987-036-01
X-4947-961-1
103
104
105
106
107
108
109
110
* 111
Remark
– 94 –
Remark
(4) CHASSIS SECTION
not supplied
E, AR, MX, PX
152
151
#1
#2
UK
#1
not supplied
#1
T901
CNP901
160
153
UK, MX,
PX
#4
154
PX
#1
158
not
supplied
CNP901
155
CDM37L-5BD29AL
AEP, EE,
AR
AR
#1
159
#1
#1
CNP901
US, CND
#1
156
CNP901
not supplied
AUS
CNP901
157
not supplied
The components identified by
mark ! or dotted line with
mark ! are critical for safety.
Replace only with part number
specified.
#1
Ref. No.
Part No.
Description
127
* 151
152
153
153
* 154
4-948-236-01
1-664-014-11
3-701-948-20
3-703-244-00
4-966-266-01
A-4392-442-A
CUSHION (107)
TRANS BOARD
LABEL (T4A), FUSE (E, AR, MX, PX)
BUSHING (FBS001), CORD (EXCEPT XB3:E,MX)
BUSHING (S) (FBS002), CORD (XB3: E, MX)
POWER AMP BOARD, COMPLETE (US, CND)
* 154
A-4392-460-A POWER AMP BOARD, COMPLETE
(E, AR, MX, AUS, PX)
A-4392-465-A POWER AMP BOARD, COMPLETE (AEP, EE, UK)
A-4392-438-A MAIN BOARD, COMPLETE (US, CND)
A-4392-457-A MAIN BOARD, COMPLETE (E, AR, MX)
A-4392-461-A MAIN BOARD, COMPLETE (AEP, UK)
*
*
*
*
154
155
155
155
* 155
* 155
A-4392-703-A MAIN BOARD, COMPLETE (EE)
A-4392-706-A MAIN BOARD, COMPLETE (AUS, PX)
Remark
Les composants identifiés par une
marque ! sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le neméro spécifié.
Ref. No.
Part No.
Description
156
157
! 158
! 159
* 160
1-777-868-11
X-4941-228-1
1-569-007-11
1-569-008-11
4-988-533-11
WIRE (FLAT TYPE) (19 CORE)
FOOT (F22125H-M)
ADAPTOR, CONVERSION 2P (PX)
ADAPTOR, CONVERSION 2P (AR)
HOLDER, PCB
! CNP901
! CNP901
! CNP901
! CNP901
! CNP901
1-558-943-41
1-575-042-21
1-575-651-21
1-696-845-11
1-751-529-11
CORD, POWER (E, MX, PX)
CORD, POWER (US, CND)
CORD, POWER (AEP, EE, AR)
CORD, POWER (AUS)
CORD, POWER (UK)
! T901
! T901
! T901
1-431-045-11 TRANSFORMER, POWER (US, CND)
1-431-047-11 TRANSFORMER, POWER (AEP, EE, UK)
1-431-048-11 TRANSFORMER, POWER (E, AR, MX, AUS, PX)
– 95 –
Remark
(5) TAPE MECHANISM DECK SECTION-1
(TCM-220WR2)
207
201
208
205
209
#5
#5
206
#5
205
207
203
202
not supplied
204
#1
Ref. No.
201
202
203
204
205
Part No.
Description
X-4947-943-1
X-4947-944-1
4-959-231-11
4-959-232-11
3-354-963-01
HOLDER (L) ASSY, CASSETTE
HOLDER (R) ASSY, CASSETTE
SPRING (L), TORSION
SPRING (R), TORSION
DAMPER
Remark
Ref. No.
Part No.
Description
* 206
207
208
209
4-980-439-01
3-354-957-01
3-354-953-01
3-354-954-01
FULCRUM, HOLDER
JOINT (LOCK LEVER)
LEVER (LOCK LEVER L)
LEVER (LOCK LEVER R)
– 96 –
Remark
(6) TAPE MECHANISM DECK SECTION-2
(TCM-220WR2)
#6
271
(including r C)
274
rA
#6
264
not supplied
265
rA
269
263
262
rB
265
264
261
258
256
273
266
HP101
(including r A)
257
272
273
259
267
260
255
not supplied
HRPE101
(including r B)
254
268
253
256
not supplied
266
not supplied
rB
269
262
257
263
261
not supplied
259
255
258
252
260
#7
251
254
not supplied
253
not supplied
252
#7
251
Ref. No.
Part No.
Description
251
252
253
254
255
3-908-560-01
3-919-684-01
X-3373-113-1
3-908-556-01
3-908-558-02
SPRING, AZIMUTH ADJUSTMENT
SCREW, AZIMUTH ADJUSTMENT
SLIDER (HEAD) ASSY
SPRING, HEAD TOGGLE
FITTING BLOCK, HEAD
256
* 257
258
259
260
3-908-557-02
3-908-559-01
3-908-555-01
3-917-143-11
3-388-848-01
ROTARY BLOCK, HEAD
STOPPER, AZIMUTH
SLIDER (REV SLIDER)
SPRING, TENSION
SCREW (P2X6) (B TIGHT)
261
262
263
3-939-371-01 SPRING (1), TENSION
X-3369-909-1 PINCH LEVER (REV) ASSY
X-3369-908-1 PINCH LEVER (FWD) ASSY
Remark
Ref. No.
Part No.
Description
264
265
266
267
268
3-908-613-01
3-917-141-01
X-3371-305-1
3-669-465-01
X-3370-173-1
GEAR (S), REEL
SPRING, COMPRESSION
REEL (T) ASSY
WASHER (1.5), STOPPER
TU ASSY
269
* 271
272
273
274
3-911-116-21
A-2007-131-A
3-930-972-01
3-917-142-01
3-911-116-11
RIVET, PUSH
AUDIO BOARD, COMPLETE
DETENT, HALF
SPRING, COMPRESSION
RIVET, PUSH
Remark
HP101 1-500-093-11 HEAD, MAGNETIC (PLAYBACK) (DECK A)
HRPE1011-500-094-11 HEAD, MAGNETIC (REC/PB/ERASE) (DECK B)
– 97 –
(7) TAPE MECHANISM DECK SECTION-3
(TCM-220WR2)
r C : MOTOR board (supplied with AUDIO board)
M2
rC
318
319
#10
317
320
#11
310
321
#10
311
302
321
309
316
310
#7
324
313
315
308
323
306
319
305
312
307
322
307
304
314
313
#8
303
301
#9
302
#9
M1
Ref. No.
Part No.
Description
301
302
303
304
305
3-908-597-01
3-908-608-11
X-3372-930-1
X-3370-169-1
3-928-047-01
CAM (A)
SCREW, STEP
ARM (A) ASSY, FR
FLYWHEEL (AR) ASSY
PULLEY, TENSION
306
307
308
309
310
3-908-599-01
3-908-601-01
3-908-603-01
X-3367-593-1
3-908-605-01
LEVER (REV-A)
SPRING (REV LEVER), TORSION
LEVER (TRIGGER A)
FLYWHEEL (BF) ASSY
SPRING (TRIGGER), TORSION
311
312
313
3-908-609-01 GEAR, TRIGGER
3-913-845-11 BELT (A)
3-913-846-11 BELT (FR)
not supplied
Remark
Ref. No.
Part No.
Description
314
315
* 316
317
318
X-3370-171-1
3-908-600-01
1-650-669-11
3-908-598-01
X-3372-931-1
FLYWHEEL (BR) ASSY
LEVER (REV-B)
LEAF SWITCH BOARD
CAM (B)
ARM (B) ASSY, FR
319
320
321
322
323
3-914-111-01
3-908-604-01
3-911-115-01
3-917-176-11
X-3370-172-1
SPRING (FR), TORSION
LEVER (TRIGGER B)
WASHER, STOPPER
BELT (B)
FLYWHEEL (AF) ASSY
324
M1
M2
X-3371-441-1 CHASSIS ASSY, MECHANICAL
X-3371-223-1 MOTOR ASSY, CAPSTAN
A-2004-410-A MOTOR ASSY, DC (TRIGGER)
– 98 –
Remark
(8) CD MECHANISM DECK SECTION
(CDM37L-5BD29AL)
352
351
351
358
351
355
353
354
356
359
357 #1
360
361
360
359
359
360
375
373
374
372
362
352
368
368
M201
367
368
BU-5BD29AL
369
not
supplied
369
365 #1
363
361
370
366
#1
#1
Ref. No.
#1
Ref. No.
Part No.
Description
SCREW, STEP
BELT (TIMING)
GEAR (PULLEY) ASSY
GEAR (MID)
ROLLER (CAM)
* 364
365
* 366
* 367
368
A-4673-765-A
4-978-426-01
1-659-059-13
1-659-058-13
4-933-134-01
CD MOTOR BOARD, COMPLETE
INDICATOR (NO.)
BD LED BOARD
TABLE SENSOR BOARD
SCREW (+PTPWH M2.6X6)
CAM (HOLDER)
MAGNET
TABLE, DISC
SHAFT (ROLLER)
ROLLER ASSY
369
* 370
371
372
373
4-958-593-01
4-978-419-01
4-917-583-71
4-989-493-01
4-989-494-01
SPRING (BU), COMPRESSION
HOLDER (BU-5)
BRACKET, YOKE
SLIDER (37)
SCREW (SLIDER), STEP
Part No.
Description
351
352
353
354
355
4-987-976-01
4-944-490-01
A-4660-978-A
4-978-421-01
4-978-425-01
356
357
358
359
360
4-978-420-01
1-452-538-11
4-978-417-01
4-934-376-01
X-4924-457-1
* 361
* 362
* 363
371
364
4-978-583-01 BRACKET (BU)
4-978-418-01 CHASSIS
4-980-385-01 HOLDER (SW)
Remark
374
375
M201
– 99 –
4-989-819-01 SPRING, TENSION
4-989-491-21 COVER, LENS
A-4660-977-A MOTOR ASSY (TABLE)
Remark
(9) BASE UNIT SECTION
(BU-5BD29AL)
401
402
#12
403
rA
M101
(including
r A)
405
404
M102
404
406
407
408
Ref. No.
Part No.
Description
! 401
402
403
404
405
8-820-020-01
1-769-069-11
4-917-567-21
4-951-940-01
4-917-565-01
OPTICAL PICK-UP KSS-213D/Q-NP
WIRE (FLAT TYPE) (16 CORE)
GEAR (M)
INSULATOR (BU)
SHAFT, SLED
Remark
Ref. No.
Part No.
Description
406
* 407
408
M101
M102
4-917-564-01
A-4699-522-A
4-951-620-01
X-4917-523-4
X-4917-504-1
GEAR (P), FLATNESS
BD BOARD, COMPLETE
SCREW (2.6X8), +BVTP
MOTOR ASSY (SPINDLE)
MOTOR ASSY (SLED)
– 100 –
The components identified by
mark ! or dotted line with
mark ! are critical for safety.
Replace only with part number
specified.
Remark
Les composants identifiés par une
marque ! sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le neméro spécifié.
SECTION 8
ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts specified in the diagrams or the components used on
the set.
• -XX and -X mean standardized parts, so they
may have some difference from the original one.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when ordering these items.
Ref. No.
Part No.
*
A-2007-131-A AUDIO BOARD, COMPLETE
*********************
(including MOTOR BOARD)
AUDIO
• SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. .
uPA. . : µPA. .
uPB. . : µPB. .
uPC. . : µPC. .
uPD. . : µPD. .
The components identified by mark
! or dotted line with mark ! are
critical for safety.
Replace only with part number
specified.
• CAPACITORS
uF: µF
Les composants identifiés par une
marque ! sont critiquens pour la
sécurité.
Ne les remplacer que par une pièce
portant le neméro spécifié.
• COILS
uH: µH
• Abbreviation
AR : Argentine
AUS : Australian
CND : Canadian
EE : East European
MX : Mexican
Description
Remark
Ref. No.
C642
C651
When indicating parts by reference
number, please include the board.
Part No.
Description
Remark
1-104-664-11 ELECT
1-161-494-00 CERAMIC
47uF
20%
0.022uF
16V
25V
< CONNECTOR >
< CAPACITOR >
C301
C302
C303
C304
C305
1-162-289-31
1-126-968-11
1-162-282-31
1-130-483-00
1-107-715-11
CERAMIC
ELECT
CERAMIC
MYLAR
ELECT
390PF
100uF
100PF
0.01uF
22uF
10%
20%
10%
5%
20%
50V
6.3V
50V
50V
16V
C311
C313
C314
C315
C331
1-162-289-31
1-162-282-31
1-130-487-00
1-126-233-11
1-137-427-11
CERAMIC
CERAMIC
MYLAR
ELECT
FILM
390PF
100PF
0.022uF
22uF
120PF
10%
10%
5%
20%
5%
50V
50V
50V
25V
50V
C332
C333
C401
C402
C403
1-162-288-31
1-162-209-31
1-162-289-31
1-126-968-11
1-162-282-31
CERAMIC
CERAMIC
CERAMIC
ELECT
CERAMIC
330PF
27PF
390PF
100uF
100PF
10%
5%
10%
20%
10%
50V
50V
50V
6.3V
50V
C404
C405
C411
C413
C414
1-130-483-00
1-107-715-11
1-162-289-31
1-162-282-31
1-130-487-00
MYLAR
ELECT
CERAMIC
CERAMIC
MYLAR
0.01uF
22uF
390PF
100PF
0.022uF
5%
20%
10%
10%
5%
50V
16V
50V
50V
50V
C415
C431
C432
C433
C601
1-126-233-11
1-137-427-11
1-162-288-31
1-162-209-31
1-104-396-11
ELECT
FILM
CERAMIC
CERAMIC
ELECT
22uF
120PF
330PF
27PF
10uF
20%
5%
10%
5%
20%
25V
50V
50V
50V
16V
C602
C611
C612
C621
C622
1-104-396-11
1-124-907-11
1-124-907-11
1-137-150-11
1-126-961-11
ELECT
ELECT
ELECT
FILM
ELECT
10uF
10uF
10uF
0.01uF
2.2uF
20%
20%
20%
5%
20%
16V
50V
50V
100V
50V
C623
C624
C625
C627
C628
1-136-155-00
1-130-481-00
1-130-481-00
1-124-903-11
1-136-153-00
FILM
MYLAR
MYLAR
ELECT
FILM
0.015uF 5%
0.0068uF 5%
0.0068uF 5%
1uF
20%
0.01uF 5%
50V
50V
50V
50V
50V
* CN601
* CN602
* CN651
1-568-864-11 SOCKET, CONNECTOR 21P
1-564-718-11 PIN, CONNECTOR (SMALL TYPE) 2P
1-564-521-11 PLUG, CONNECTOR 6P
< IC >
IC601
IC602
IC611
8-759-111-44 IC uPC4570C-1
8-759-143-54 IC uPC1330HA
8-759-111-44 IC uPC4570C-1
< COIL >
L331
L431
1-410-780-11 INDUCTOR
1-410-780-11 INDUCTOR
27mH
27mH
< TRANSISTOR >
Q621
Q622
Q623
Q651
8-729-142-46
8-729-142-46
8-729-801-93
8-729-900-65
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC2001-LK
2SC2001-LK
2SD1387
DTA144ES
< RESISTOR >
R301
R302
R303
R304
R305
1-247-881-00
1-249-409-11
1-249-433-11
1-247-889-00
1-247-858-11
CARBON
CARBON
CARBON
CARBON
CARBON
120K
220
22K
270K
13K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R311
R312
R314
R315
R331
1-247-881-00
1-247-807-31
1-247-882-11
1-247-850-11
1-249-430-11
CARBON
CARBON
CARBON
CARBON
CARBON
120K
100
130K
6.2K
12K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R401
R402
R403
R404
R405
1-247-881-00
1-249-409-11
1-249-433-11
1-247-889-00
1-247-858-11
CARBON
CARBON
CARBON
CARBON
CARBON
120K
220
22K
270K
13K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
– 101 –
AUDIO
Ref. No.
BD
Part No.
Description
Remark
R411
R412
R414
R415
R431
1-247-881-00
1-247-807-31
1-247-882-11
1-247-850-11
1-249-430-11
CARBON
CARBON
CARBON
CARBON
CARBON
120K
100
130K
6.2K
12K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R601
R602
R608
R609
R611
1-249-409-11
1-249-409-11
1-249-409-11
1-249-433-11
1-249-409-11
CARBON
CARBON
CARBON
CARBON
CARBON
220
220
220
22K
220
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R612
! R621
! R622
R623
R624
1-249-409-11
1-212-851-00
1-212-851-00
1-249-432-11
1-249-432-11
CARBON
FUSIBLE
FUSIBLE
CARBON
CARBON
220
5.6
5.6
18K
18K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R625
R651
R652
R653
1-249-429-11
1-247-856-00
1-247-856-00
1-249-441-11
CARBON
CARBON
CARBON
CARBON
10K
11K
11K
100K
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
F
F
< VARIABLE RESISTOR >
RV301
RV311
RV341
RV401
RV411
1-238-598-11
1-238-598-11
1-238-551-11
1-238-598-11
1-238-598-11
RES, ADJ, CARBON 2.2K
RES, ADJ, CARBON 2.2K
RES, ADJ, CARBON 220K
RES, ADJ, CARBON 2.2K
RES, ADJ, CARBON 2.2K
RV441
RV651
RV652
1-238-551-11 RES, ADJ, CARBON 220K
1-238-599-11 RES, ADJ, CARBON 4.7K
1-238-599-11 RES, ADJ, CARBON 4.7K
< TRANSFORMER >
T621
1-423-980-11 TRANSFORMER, BIAS OSCILLATION
************************************************************
A-4699-522-A BD BOARD, COMPLETE
*******************
*
< CAPACITOR >
C101
C102
C103
C105
C106
1-126-607-11
1-163-141-00
1-164-346-11
1-163-038-91
1-164-161-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
20%
0.001uF 5%
1uF
0.1uF
0.0022uF 10%
4V
50V
16V
25V
100V
C107
C108
C109
C110
C111
1-164-161-11
1-164-232-11
1-164-232-11
1-163-989-11
1-163-017-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022uF 10%
0.01uF
0.01uF
0.033uF 10%
0.0047uF 5%
100V
50V
50V
25V
50V
C112
1-163-017-00 CERAMIC CHIP
0.0047uF 5%
50V
The components identified by
mark ! or dotted line with
mark ! are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque ! sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le neméro spécifié.
Ref. No.
Part No.
Description
Remark
C113
C114
C115
C116
1-164-161-11
1-164-005-11
1-126-607-11
1-163-016-00
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
0.0022uF 10%
0.47uF
47uF
20%
0.0039uF 10%
100V
25V
4V
50V
C117
C118
C119
C120
C121
1-164-005-11
1-164-004-11
1-163-038-91
1-124-779-00
1-163-038-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
0.47uF
0.1uF
0.1uF
10uF
0.1uF
25V
25V
25V
16V
25V
C122
C123
C124
C125
C126
1-164-232-11
1-163-038-91
1-126-607-11
1-164-232-11
1-163-038-91
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
47uF
0.01uF
0.1uF
C127
C128
C129
C130
C131
1-164-161-11
1-163-135-00
1-163-038-91
1-164-336-11
1-164-346-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022uF 10%
560PF 5%
0.1uF
0.33uF
1uF
100V
50V
25V
25V
16V
C140
C154
C161
C162
C163
1-110-501-11
1-163-235-11
1-164-005-11
1-164-232-11
1-163-117-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.33uF
22PF
0.47uF
0.01uF
100PF
50V
50V
25V
50V
50V
C164
C165
C166
C167
C168
1-163-145-00
1-164-004-11
1-163-137-00
1-163-121-00
1-163-137-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0015uF 5%
0.1uF
10%
680PF 5%
150PF 5%
680PF 5%
50V
25V
50V
50V
50V
C169
C170
C171
C173
C174
1-163-121-00
1-163-099-00
1-163-237-11
1-163-038-91
1-163-038-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
150PF
18PF
27PF
0.1uF
0.1uF
50V
50V
50V
25V
25V
C175
C176
C177
C178
C179
1-163-038-91
1-163-038-91
1-163-038-91
1-163-038-91
1-163-038-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
C181
C182
C183
C185
C188
1-126-205-11
1-126-393-11
1-124-778-00
1-164-232-11
1-163-235-11
ELECT CHIP
ELECT
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
33uF
22uF
0.01uF
22PF
20%
20%
20%
5%
6.3V
10V
6.3V
50V
50V
C189
1-163-235-11 CERAMIC CHIP
22PF
5%
50V
< CONNECTOR >
CNU101 1-777-937-11 CONNECTOR, FFC/FPC 16P
– 102 –
10%
20%
20%
5%
5%
5%
5%
5%
50V
25V
4V
50V
25V
25V
25V
25V
25V
25V
BD
Ref. No.
Part No.
Description
Remark
Ref. No.
CNU102 1-778-874-11 CONNECTOR, FFC (LIF (NON-ZIF)) 19P
Part No.
BD LED
Description
Remark
R135
R136
1-216-065-00 METAL CHIP
1-216-073-00 METAL CHIP
4.7K
10K
5%
5%
1/10W
1/10W
R137
R138
R156
R157
R158
1-216-065-00
1-216-025-91
1-216-081-00
1-216-069-00
1-216-001-00
METAL CHIP
METAL GLAZE
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
100
22K
6.8K
10
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R159
R161
R162
R163
R164
1-216-121-91
1-216-097-91
1-216-073-00
1-216-121-91
1-216-061-00
METAL GLAZE
METAL GLAZE
METAL CHIP
METAL GLAZE
METAL CHIP
1M
100K
10K
1M
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R165
R166
R167
R168
R169
1-216-049-91
1-216-073-00
1-216-081-00
1-216-073-00
1-216-079-00
METAL GLAZE
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
10K
22K
10K
18K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R170
R171
R172
R173
R174
1-216-081-00
1-216-073-00
1-216-079-00
1-216-025-91
1-216-033-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL GLAZE
METAL CHIP
22K
10K
18K
100
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R175
R176
R177
R178
R179
1-216-025-91
1-216-025-91
1-216-025-91
1-216-025-91
1-216-025-91
METAL GLAZE
METAL GLAZE
METAL GLAZE
METAL GLAZE
METAL GLAZE
100
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R180
R181
R188
R190
R191
1-216-025-91
1-216-025-91
1-216-037-00
1-216-097-91
1-216-105-91
METAL GLAZE
METAL GLAZE
METAL CHIP
METAL GLAZE
METAL GLAZE
100
100
330
100K
220K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< FERRITE BEAD >
FB101
FB103
1-414-234-11 INDUCTOR, FERRITE BEAD
1-414-234-11 INDUCTOR, FERRITE BEAD
< IC >
IC101
IC102
IC103
8-752-080-62 IC CXA1992AR
8-759-429-32 IC BA5941FP-E2
8-752-378-66 IC CXD2519Q
< JUMPER RESISTOR >
JW101
JW104
1-216-295-91 CONDUCTOR, CHIP
1-216-295-91 CONDUCTOR, CHIP
(2012)
(2012)
< TRANSISTOR >
Q101
8-729-010-08 TRANSISTOR MSB710-R
< RESISTOR >
R102
R104
R105
R106
R107
1-216-001-00
1-216-093-00
1-216-088-00
1-216-088-00
1-216-088-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10
68K
43K
43K
43K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R108
R109
R114
R115
R116
1-216-088-00
1-216-093-00
1-216-101-00
1-216-101-00
1-216-061-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
43K
68K
150K
150K
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R117
R118
R119
R120
R121
1-216-069-00
1-216-063-91
1-216-085-00
1-216-089-91
1-216-114-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL GLAZE
METAL GLAZE
6.8K
3.9K
33K
47K
510K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R122
R123
R124
R125
R126
1-216-097-91
1-216-099-00
1-216-091-00
1-216-069-00
1-216-063-91
METAL GLAZE
METAL CHIP
METAL CHIP
METAL CHIP
METAL GLAZE
100K
120K
56K
6.8K
3.9K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R127
R128
R129
R130
R131
1-216-089-91
1-216-098-00
1-216-025-91
1-216-079-00
1-216-079-00
METAL GLAZE
METAL CHIP
METAL GLAZE
METAL CHIP
METAL CHIP
47K
110K
100
18K
18K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R132
R133
R134
1-216-061-00 METAL CHIP
1-216-061-00 METAL CHIP
1-216-065-00 METAL CHIP
3.3K
3.3K
4.7K
5%
5%
5%
1/10W
1/10W
1/10W
< SWITCH >
S101
1-572-085-11 SWITCH, LEAF
< VIBRATOR >
X101
1-767-408-21 VIBRATOR, CRYSTAL (16.9344MHz)
************************************************************
1-659-059-13 BD LED BOARD
************
*
< DIODE >
D201
8-719-032-98 DIODE SEL5820A
< TRANSISTOR >
Q201
– 103 –
8-729-119-78 TRANSISTOR 2SC403SP-51
BD LED
Ref. No.
CD MOTOR
Part No.
CD-A SW
Description
CD-B1 SW
Remark
Ref. No.
CD-B2 SW
Part No.
< RESISTOR >
A-4673-765-A CD MOTOR BOARD, COMPLETE
*************************
1-124-907-11 ELECT
1-164-159-21 CERAMIC
1-124-907-11 ELECT
10uF
0.1uF
10uF
20%
20%
S661
S662
S663
S664
S665
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
50V
50V
50V
1-664-010-11 CD-B1 SW BOARD
***************
*
< CONNECTOR >
* CN201
< CONNECTOR >
1-568-947-11 PIN, CONNECTOR 9P
* CN642
1-568-943-11 PIN, CONNECTOR 5P
< IC >
IC201
< DIODE >
8-759-365-94 IC TA8409S
D645
D646
D647
< COIL >
L201
1-408-117-00 INDUCTOR
8-719-058-03 DIODE SEL5423E-TP15 (· CD PLAY)
8-719-057-97 DIODE SEL5923A-TP15 (P PAUSE)
8-719-058-03 DIODE SEL5423E-TP15 (· CD PLAY)
10uH
< RESISTOR >
< RESISTOR >
R205
R206
SWITCH, TACTILE (DISC 1)
SWITCH, TACTILE (DISC 2)
SWITCH, TACTILE (DISC 3)
SWITCH, TACTILE (DISC 4)
SWITCH, TACTILE (DISC 5)
S666
1-554-303-21 SWITCH, TACTILE (FLASH)
S667
1-554-303-21 SWITCH, TACTILE (NON-STOP)
S668
1-554-303-21 SWITCH, TACTILE (LOOP)
************************************************************
< CAPACITOR >
C201
C202
C203
Remark
< SWITCH >
R201
1-247-863-91 CARBON
22K
5%
1/4W
R202
1-249-411-11 CARBON
330
5%
1/4W
R203
1-249-437-11 CARBON
47K
5%
1/4W
************************************************************
*
Description
1-249-427-11 CARBON
1-249-425-11 CARBON
6.8K
4.7K
5%
5%
1/4W
1/4W
R745
R746
R747
R748
R749
1-249-419-11
1-249-421-11
1-247-843-11
1-249-425-11
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
R750
R751
1-247-807-31 CARBON
1-247-807-31 CARBON
1.5K
2.2K
3.3K
4.7K
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
100
100
5%
5%
1/4W
1/4W
< SWITCH >
S201
1-762-587-11 SWITCH, PUSH (1 KEY)
************************************************************
< SWITCH >
1-664-009-11 CD-A SW BOARD
*************
*
< DIODE >
D641
8-719-058-04 DIODE SEL5223S-TP15 (NON-STOP)
< RESISTOR >
S676
1-554-303-21 SWITCH, TACTILE (·)
S677
1-554-303-21 SWITCH, TACTILE (p)
S678
1-554-303-21 SWITCH, TACTILE (P)
S679
1-554-303-21 SWITCH, TACTILE (DISC SKIP)
************************************************************
1-664-011-11 CD-B2 SW BOARD
**************
*
R731
R732
R733
R734
R735
1-247-843-11
1-249-425-11
1-249-427-11
1-249-429-11
1-249-432-11
CARBON
CARBON
CARBON
CARBON
CARBON
3.3K
4.7K
6.8K
10K
18K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R736
R737
R741
1-249-436-11 CARBON
1-247-881-00 CARBON
1-247-807-31 CARBON
39K
120K
100
5%
5%
5%
1/4W
1/4W
1/4W
< RESISTOR >
R752
R753
R754
R755
R756
– 104 –
1-249-427-11
1-249-429-11
1-249-432-11
1-249-436-11
1-247-881-00
CARBON
CARBON
CARBON
CARBON
CARBON
6.8K
10K
18K
39K
120K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
CD-B2 SW
Ref. No.
Part No.
DOOR SW
Description
Remark
HEADPHONE-MIC
Ref. No.
Part No.
< SWITCH >
S681
S682
S683
S684
S685
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
SWITCH, TACTILE (‚)
SWITCH, TACTILE (REPEAT)
SWITCH, TACTILE (PLAY MODE)
SWITCH, TACTILE (1/ALL DISCS)
SWITCH, TACTILE (EDIT)
J760
J761
< CAPACITOR >
1-164-159-21 CERAMIC
0.1uF
1-770-226-11 JACK (LARGE TYPE) (PHONES)
1-770-226-11 JACK (LARGE TYPE) (MIC)
R760
R761
R764
R765
R766
1-249-429-11
1-249-417-11
1-249-441-11
1-249-417-11
1-247-863-91
CARBON
CARBON
CARBON
CARBON
CARBON
10K
1K
100K
1K
22K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R767
R769
R770
1-249-429-11 CARBON
1-247-885-00 CARBON
1-247-807-31 CARBON
10K
180K
100
5%
5%
5%
1/4W
1/4W
1/4W
50V
< VARIABLE RESISTOR >
< CONNECTOR >
CN661
Remark
< RESISTOR >
1-664-016-11 DOOR SW BOARD
*************
C691
Description
< JACK >
S686
1-554-303-21 SWITCH, TACTILE (º)
S711
1-467-968-11 ENCODER, ROTARY (≠ AMS ±)
************************************************************
*
LEAF SWITCH
RV760 1-225-366-11 RES, VAR, CARBON 50K (MIC LEVEL)
************************************************************
1-506-481-11 PIN, CONNECTOR 2P
1-650-669-11 LEAF SWITCH BOARD
*****************
*
< SWITCH >
S691
1-771-057-11 SWITCH (6 OPEN)
************************************************************
< CONNECTOR >
* CN1001 1-568-854-11 SOCKET, CONNECTOR 11P
A-4392-452-A HEADPHONE-MIC BOARD, COMPLETE
******************************
*
< CAPACITOR >
Q1001
Q1002
C760
C761
C764
C765
C766
1-162-306-11
1-126-961-11
1-162-294-31
1-162-215-31
1-162-290-31
CERAMIC
ELECT
CERAMIC
CERAMIC
CERAMIC
0.01uF
2.2uF
0.001uF
47PF
470PF
20%
20%
10%
5%
10%
16V
50V
50V
50V
50V
C767
C769
C770
C771
C773
1-162-215-31
1-162-282-31
1-126-961-11
1-126-959-11
1-126-964-11
CERAMIC
CERAMIC
ELECT
ELECT
ELECT
47PF
100PF
2.2uF
0.47uF
10uF
5%
10%
20%
20%
20%
50V
50V
50V
50V
50V
C774
C775
C776
C794
C795
1-126-964-11
1-162-294-31
1-162-294-31
1-164-159-21
1-164-159-21
ELECT
CERAMIC
CERAMIC
CERAMIC
CERAMIC
10uF
20%
0.001uF 10%
0.001uF 10%
0.1uF
0.1uF
50V
50V
50V
50V
50V
< CONNECTOR >
* CN701
< TRANSISTOR >
1-568-935-11 PIN, CONNECTOR 8P
< RESISTOR >
R1001
R1002
R1003
R1004
R1005
1-247-818-11
1-247-820-11
1-249-414-11
1-247-834-11
1-247-818-11
CARBON
CARBON
CARBON
CARBON
CARBON
300
360
560
1.3K
300
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
< SWITCH >
S1001
S1002
S1004
S1005
S1006
1-692-832-11
1-692-832-11
1-571-281-21
1-571-281-21
1-572-248-21
SWITCH, PUSH (1 KEY) (A PLAY)
SWITCH, PUSH (1 KEY) (B PLAY)
SWITCH, LEAF (A HALF)
SWITCH, LEAF (A CrO2)
SWITCH, LEAF (REC A)
S1007 1-572-248-21 SWITCH, LEAF (B HALF)
S1008 1-571-281-21 SWITCH, LEAF (REC B)
S1009 1-571-281-21 SWITCH, LEAF (B CrO2)
************************************************************
< IC >
IC760
8-749-010-90 TRANSISTOR PHOTO REFLECTOR NJL5165KA-H
8-749-010-90 TRANSISTOR PHOTO REFLECTOR NJL5165KA-H
8-759-634-51 IC M5218AP
– 105 –
LED
MAIN
Ref. No.
Part No.
Description
*
1-664-017-11 LED BOARD
*********
Remark
Description
Remark
1-162-288-31 CERAMIC
330PF
C152
C153
C154
1-162-282-31 CERAMIC
1-162-282-31 CERAMIC
1-126-962-11 ELECT
100PF
100PF
3.3uF
10%
50V
(AEP, UK, EE)
10%
50V
10%
50V
20%
50V
C155
C156
C157
C158
1-162-600-11
1-162-301-11
1-126-956-91
1-126-967-11
CERAMIC
CERAMIC
ELECT
ELECT
0.0047uF 30%
0.0015uF 30%
0.1uF
20%
47uF
20%
16V
16V
50V
10V
(AEP, UK, EE)
C171
C173
C181
1-162-286-21 CERAMIC
1-162-306-11 CERAMIC
1-136-495-11 FILM
220PF 10%
0.01uF 20%
0.068uF 5%
C182
1-136-495-11 FILM
0.068uF 5%
50V
16V
50V
(AEP, UK, EE)
50V
(AEP, UK, EE)
C183
1-162-294-31 CERAMIC
0.001uF 10%
C184
1-164-159-21 CERAMIC
0.1uF
C201
1-136-169-00 FILM
0.22uF
5%
C202
C203
C204
C205
C206
1-136-169-00
1-130-493-00
1-130-493-00
1-130-486-00
1-130-486-00
FILM
MYLAR
MYLAR
MYLAR
MYLAR
0.22uF
0.068uF
0.068uF
0.018uF
0.018uF
5%
5%
5%
10%
10%
50V
50V
50V
50V
50V
C207
C208
C209
C210
C211
1-130-480-00
1-130-479-00
1-130-474-00
1-126-964-11
1-126-964-11
MYLAR
MYLAR
MYLAR
ELECT
ELECT
0.0056uF 5%
0.0047uF 5%
0.0018uF 5%
10uF
20%
10uF
20%
50V
50V
50V
50V
50V
16V
16V
50V
10V
(AEP, UK, EE)
C212
C213
C214
C215
C216
1-130-481-00
1-136-169-00
1-136-169-00
1-162-294-31
1-136-167-00
MYLAR
FILM
FILM
CERAMIC
FILM
0.0068uF 5%
0.22uF 5%
0.22uF 5%
0.001uF 10%
0.15uF 5%
50V
50V
50V
50V
50V
50V
(AEP, UK, EE)
220PF 10%
50V
0.01uF 20%
16V
0.068uF 5%
50V
(AEP, UK, EE)
C221
C222
C223
C224
C226
1-126-967-11
1-126-967-11
1-126-964-11
1-162-290-31
1-126-964-11
ELECT
ELECT
ELECT
CERAMIC
ELECT
47uF
47uF
10uF
470PF
10uF
20%
20%
20%
10%
20%
10V
10V
50V
50V
50V
C227
C231
C251
C252
C253
1-164-159-21
1-126-960-11
1-136-169-00
1-136-169-00
1-130-493-00
CERAMIC
ELECT
FILM
FILM
MYLAR
0.1uF
1uF
0.22uF
0.22uF
0.068uF
20%
5%
5%
5%
50V
50V
50V
50V
50V
C254
C255
C256
1-130-493-00 MYLAR
1-130-486-00 MYLAR
1-130-486-00 MYLAR
0.068uF 5%
0.018uF 10%
0.018uF 10%
50V
50V
50V
1-506-481-11 PIN, CONNECTOR 2P
< DIODE >
D671
D672
D673
D674
Part No.
C151
< CONNECTOR >
CN671
Ref. No.
8-719-058-03
8-719-058-03
8-719-058-03
8-719-058-03
DIODE
DIODE
DIODE
DIODE
SEL5423E-TP15
SEL5423E-TP15
SEL5423E-TP15
SEL5423E-TP15
< RESISTOR >
R791
1-249-412-11 CARBON
390
5%
1/4W
************************************************************
*
*
*
*
*
A-4392-438-A
A-4392-457-A
A-4392-706-A
A-4392-461-A
A-4392-703-A
MAIN BOARD, COMPLETE (US, CND)
MAIN BOARD, COMPLETE (E, AR, MX)
MAIN BOARD, COMPLETE (AUS, PX)
MAIN BOARD, COMPLETE (AEP, UK)
MAIN BOARD, COMPLETE (EE)
*********************
*
4-870-539-11 PLATE, GROUND
7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
< CAPACITOR >
C101
1-162-288-31 CERAMIC
330PF
C102
C103
C104
1-162-282-31 CERAMIC
1-162-282-31 CERAMIC
1-126-962-11 ELECT
100PF
100PF
3.3uF
C105
C106
C107
C108
1-162-600-11
1-162-301-11
1-126-956-91
1-126-967-11
0.0047uF 30%
0.0015uF 30%
0.1uF
20%
47uF
20%
C109
1-164-159-21 CERAMIC
C121
C123
C131
1-162-286-21 CERAMIC
1-162-306-11 CERAMIC
1-136-495-11 FILM
C132
1-136-495-11 FILM
C133
1-162-294-31 CERAMIC
C134
1-164-159-21 CERAMIC
CERAMIC
CERAMIC
ELECT
ELECT
10%
50V
(AEP, UK, EE)
10%
50V
10%
50V
20%
50V
0.1uF
0.068uF 5%
50V
(AEP, UK, EE)
0.001uF 10%
50V
(AEP, UK, EE)
0.1uF
50V
(AEP, UK, EE)
– 106 –
50V
(AEP, UK, EE)
50V
(AEP, UK, EE)
50V
MAIN
Ref. No.
Part No.
Description
Remark
C257
C258
1-130-480-00 MYLAR
1-130-479-00 MYLAR
0.0056uF 5%
0.0047uF 5%
50V
50V
C259
C260
C261
C262
C263
1-130-474-00
1-126-964-11
1-126-964-11
1-130-481-00
1-136-169-00
MYLAR
ELECT
ELECT
MYLAR
FILM
0.0018uF 5%
10uF
20%
10uF
20%
0.0068uF 5%
0.22uF 5%
50V
50V
50V
50V
50V
C264
C276
C281
C282
C283
1-136-169-00
1-126-964-11
1-126-933-11
1-126-961-11
1-126-933-11
FILM
ELECT
ELECT
ELECT
ELECT
0.22uF
10uF
100uF
2.2uF
100uF
5%
20%
20%
20%
20%
50V
50V
10V
50V
10V
C284
C291
C301
C302
C303
1-126-923-11
1-126-959-11
1-126-965-11
1-164-159-21
1-136-165-00
ELECT
ELECT
ELECT
CERAMIC
FILM
220uF
0.47uF
22uF
0.1uF
0.1uF
20%
20%
20%
10V
50V
50V
50V
50V
C304
C305
C309
C310
C311
1-126-926-11
1-162-306-11
1-102-514-11
1-102-514-11
1-164-159-21
ELECT
CERAMIC
CERAMIC
CERAMIC
CERAMIC
1000uF
0.01uF
22P
22P
0.1uF
20%
20%
5%
5%
10V
16V
50V
50V
50V
C315
C390
C393
C394
C396
1-126-933-11
1-126-933-11
1-126-925-11
1-164-159-21
1-126-961-11
ELECT
ELECT
ELECT
CERAMIC
ELECT
100uF
100uF
470uF
0.1uF
2.2uF
20%
20%
20%
20%
10V
10V
10V
50V
50V
C398
C903
C904
C906
C909
1-126-961-11
1-136-165-00
1-126-937-11
1-126-933-11
1-126-964-11
ELECT
FILM
ELECT
ELECT
ELECT
2.2uF
0.1uF
4700uF
100uF
10uF
20%
5%
20%
20%
20%
50V
50V
16V
10V
50V
C910
C911
C912
C913
C914
1-126-933-11
1-126-964-11
1-126-916-11
1-126-943-11
1-126-952-11
ELECT
ELECT
ELECT
ELECT
ELECT
100uF
10uF
1000uF
2200uF
1000uF
20%
20%
20%
20%
20%
10V
50V
6.3V
25V
16V
C915
C916
C917
C918
C919
1-126-967-11
1-164-159-21
1-126-968-11
1-126-968-11
1-126-964-11
ELECT
CERAMIC
ELECT
ELECT
ELECT
47uF
0.1uF
100uF
100uF
10uF
20%
20%
20%
20%
16V
50V
50V
50V
50V
C920
C953
C954
C956
C1501
1-126-947-11
1-136-165-00
1-126-768-11
1-126-933-11
1-130-479-00
ELECT
FILM
ELECT
ELECT
MYLAR
47uF
20%
0.1uF
5%
2200uF 20%
100uF 20%
0.0047uF 5%
35V
50V
16V
10V
50V
C1502
1-162-290-31 CERAMIC
470PF
50V
5%
Ref. No.
Part No.
Description
Remark
C1503
C1504
C1505
C1506
1-164-159-21
1-126-960-11
1-126-964-11
1-126-964-11
CERAMIC
ELECT
ELECT
ELECT
0.1uF
1uF
10uF
10uF
20%
20%
20%
50V
50V
50V
50V
C1507
C1508
C1521
C1522
C1523
1-126-960-11
1-126-933-11
1-126-964-11
1-126-964-11
1-126-933-11
ELECT
ELECT
ELECT
ELECT
ELECT
1uF
100uF
10uF
10uF
100uF
20%
20%
20%
20%
20%
50V
10V
50V
50V
16V
C1531
C1532
C1533
C1534
C1551
1-164-159-21
1-164-159-21
1-164-159-21
1-126-935-11
1-130-479-00
CERAMIC
CERAMIC
CERAMIC
ELECT
MYLAR
0.1uF
0.1uF
0.1uF
470uF 20%
0.0047uF 5%
50V
50V
50V
16V
50V
C1552
C1553
C1554
C1555
C1556
1-162-290-31
1-164-159-21
1-126-960-11
1-126-964-11
1-126-964-11
CERAMIC
CERAMIC
ELECT
ELECT
ELECT
470PF
0.1uF
1uF
10uF
10uF
20%
20%
20%
50V
50V
50V
50V
50V
C1557
C1558
1-126-960-11 ELECT
1-126-933-11 ELECT
1uF
100uF
20%
20%
50V
10V
10%
< CONNECTOR >
10%
CN101
* CN102
* CN201
* CN201
CN202
1-778-982-11
1-568-836-11
1-568-832-11
1-568-834-11
1-568-802-11
CONNECTOR, BOARD TO BOARD 13P
SOCKET, CONNECTOR 17P
SOCKET, CONNECTOR 13P(EXCEPT AEP, UK, EE)
SOCKET, CONNECTOR 15P(AEP, UK, EE)
SOCKET, CONNECTOR 19P
* CN203
CN205
* CN206
* CN207
1-568-936-11
1-568-838-11
1-568-830-11
1-568-449-11
PIN, CONNECTOR 9P
SOCKET, CONNECTOR 21P
SOCKET, CONNECTOR 11P
HOUSING, CONNECTOR (PC BOARD) 3P
< DIODE >
D141
D281
D281
D291
D301
8-719-987-63
8-719-815-85
8-719-987-63
8-719-987-63
8-719-200-82
DIODE
DIODE
DIODE
DIODE
DIODE
1N4148M
1S1585 (US, CND)
1N4148M (EXCEPT US, CND)
1N4148M
11ES2
D302
D303
D304
D305
D306
8-719-200-82
8-719-987-63
8-719-987-63
8-719-987-63
8-719-987-63
DIODE
DIODE
DIODE
DIODE
DIODE
11ES2
1N4148M
1N4148M
1N4148M
1N4148M
D307
D902
D903
D904
D905
8-719-987-63
8-719-200-82
8-719-200-82
8-719-200-82
8-719-200-82
DIODE
DIODE
DIODE
DIODE
DIODE
1N4148M
11ES2
11ES2
11ES2
11ES2
– 107 –
MAIN
Ref. No.
Part No.
Description
Remark
D906
D907
D908
D909
D910
8-719-200-82
8-719-200-82
8-719-200-82
8-719-200-82
8-719-002-60
DIODE
DIODE
DIODE
DIODE
DIODE
11ES2
11ES2
11ES2
11ES2
UZL-33L-TA
D911
D912
D913
D914
D915
8-719-011-47
8-719-987-63
8-719-200-82
8-719-200-82
8-719-001-43
DIODE
DIODE
DIODE
DIODE
DIODE
UZ-3.3BSB-TA
1N4148M
11ES2
11ES2
UZL-11M1-TA
D951
D952
8-719-987-63 DIODE 1N4148M
8-719-987-63 DIODE 1N4148M
< FERRITE BEAD >
FB302
1-412-473-21 INDUCTOR (SMALL)
< IC >
Ref. No.
Part No.
Description
Remark
Q232
Q252
8-729-900-63 TRANSISTOR DTA124ES
8-729-119-78 TRANSISTOR 2SC403SP-51
Q253
Q254
Q281
Q282
Q283
8-729-119-78
8-729-141-30
8-729-900-36
8-729-900-63
8-729-900-36
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC403SP-51
2SC3623A-LK
DTC124ES
DTA124ES
DTC124ES
Q301
Q901
Q902
Q903
Q904
8-729-119-78
8-729-040-20
8-729-900-36
8-729-030-18
8-729-030-19
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC403SP-51
RT1P137L-TP
DTC124ES
2SD2525
2SB1640
Q905
Q906
Q907
Q1531
Q1532
8-729-040-20
8-729-900-63
8-729-119-78
8-729-801-93
8-729-900-80
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
RT1P137L-TP
DTA124ES
2SC403SP-51
2SD1387
DTC114ES
8-729-900-80 TRANSISTOR DTC114ES
8-729-119-77 TRANSISTOR 2SA1175-FEK
8-729-900-80 TRANSISTOR DTC114ES
IC101
IC102
IC201
IC231
IC281
8-759-634-50
8-759-000-48
8-759-331-39
8-759-634-50
8-759-111-68
IC
IC
IC
IC
IC
M5218AL
MC14052BCP
M62427FP
M5218AL
uPC1237HA
Q1533
Q1534
Q1535
IC301
IC302
IC901
IC902
IC903
8-759-459-31
8-759-635-63
8-759-288-53
8-759-604-86
8-759-231-53
IC
IC
IC
IC
IC
uPD780018YGF-013-3BA
M51943BSL
LA5617
M5F7807L
TA7805S
R101
1-249-417-11 CARBON
1K
5%
R102
R103
R104
1-249-417-11 CARBON
1-249-437-11 CARBON
1-249-417-11 CARBON
1K
47K
1K
5%
5%
5%
IC904
IC1501
IC1502
8-759-231-58 IC TA7812S
8-759-363-21 IC HA12203NT
8-759-822-09 IC LB1641
R105
R106
R107
R108
R109
1-247-897-11
1-249-437-11
1-249-417-11
1-249-441-11
1-247-815-91
CARBON
CARBON
CARBON
CARBON
CARBON
560K
47K
1K
100K
220
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
(AEP, UK, EE)
R121
R122
R131
1-249-424-11 CARBON
1-247-887-00 CARBON
1-260-076-11 CARBON
3.9K
220K
10
5%
5%
5%
R132
1-260-076-11 CARBON
10
5%
1/4W
1/4W
1/2W
(AEP, UK, EE)
1/2W
(AEP, UK, EE)
R133
R134
R140
R141
R142
1-260-091-11
1-260-091-11
1-249-429-11
1-249-437-11
1-249-429-11
220
220
10K
47K
10K
5%
5%
5%
5%
5%
5%
< RESISTOR >
< JACK >
J101
1-695-188-31 JACK, PIN 4P (PHONO,VIDEO IN)
< COIL >
L131
L181
L301
L393
1/4W
(AEP, UK, EE)
1/4W
1/4W
1/4W
1-420-872-00
1-420-872-00
1-410-509-11
1-410-515-11
COIL, AIR-CORE (AEP, UK, EE)
COIL, AIR-CORE (AEP, UK, EE)
INDUCTOR
10uH
INDUCTOR
33uH
< TRANSISTOR >
Q141
Q141
Q142
Q142
Q202
8-729-140-82
8-729-119-76
8-729-140-84
8-729-119-78
8-729-119-78
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
Q203
Q204
Q231
8-729-119-78 TRANSISTOR 2SC403SP-51
8-729-141-30 TRANSISTOR 2SC3623A-LK
8-729-900-63 TRANSISTOR DTA124ES
The components identified by
mark ! or dotted line with
mark ! are critical for safety.
Replace only with part number
specified.
2SA988-PAFAEA (US, CND)
2SA1175-HFE (EXCEPT US, CND)
2SC1841-PAFAEA (US, CND)
2SC403SP-51 (EXCEPT US, CND)
2SC403SP-51
Les composants identifiés par une
marque ! sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le neméro spécifié.
CARBON
CARBON
CARBON
CARBON
CARBON
! R147
1-215-893-11 METAL OXIDE
1.5K
! R147
1-215-892-11 METAL OXIDE
1K
! R147
1-216-456-00 METAL OXIDE
820
– 108 –
1/2W
1/2W
1/4W
1/4W
1/4W
2W
F
(US, CND)
5%
2W
F
(AEP, UK, EE)
5%
2W
F
(E, AR, MX, AUS, PX)
MAIN
Ref. No.
Part No.
Description
R151
1-249-417-11 CARBON
1K
5%
R152
R153
R154
1-249-417-11 CARBON
1-249-437-11 CARBON
1-249-417-11 CARBON
1K
47K
1K
5%
5%
5%
R155
R156
R157
R158
R159
1-247-897-11
1-249-437-11
1-249-417-11
1-249-441-11
1-247-815-91
560K
47K
1K
100K
220
5%
5%
5%
5%
5%
CARBON
CARBON
CARBON
CARBON
CARBON
Remark
Ref. No.
1/4W
(AEP, UK, EE)
1/4W
1/4W
1/4W
1/4W
1/4W
1/4W
1/4W
1/4W
(AEP, UK ,EE)
R171
R172
R181
1-249-424-11 CARBON
1-247-887-00 CARBON
1-260-076-11 CARBON
3.9K
220K
10
5%
5%
5%
1/4W
1/4W
1/2W
(AEP, UK, EE)
1/2W
(AEP, UK, EE)
R182
1-260-076-11 CARBON
10
5%
R183
R184
R201
R202
R203
1-260-091-11
1-260-091-11
1-249-429-11
1-247-863-91
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
220
220
10K
22K
100K
5%
5%
5%
5%
5%
1/2W
1/2W
1/4W
1/4W
1/4W
R205
R206
R207
R209
R210
1-247-863-91
1-249-421-11
1-249-431-11
1-249-441-11
1-247-891-00
CARBON
CARBON
CARBON
CARBON
CARBON
22K
2.2K
15K
100K
330K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R212
R213
R214
R215
R216
1-249-411-11
1-249-429-11
1-249-437-11
1-247-903-00
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
330
10K
47K
1M
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R217
R221
R222
R226
R227
1-249-437-11
1-249-425-11
1-249-425-11
1-249-421-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
47K
4.7K
4.7K
2.2K
100K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R228
R231
R232
R234
R235
1-249-429-11
1-249-437-11
1-249-437-11
1-247-886-11
1-249-421-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
47K
47K
200K
2.2K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R236
R253
R257
R259
R260
1-249-441-11
1-249-441-11
1-249-431-11
1-249-441-11
1-247-891-00
CARBON
CARBON
CARBON
CARBON
CARBON
100K
100K
15K
100K
330K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R262
R263
R264
R265
R266
1-249-411-11
1-249-429-11
1-249-437-11
1-247-903-00
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
330
10K
47K
1M
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
Part No.
Description
R267
R271
R272
R276
R277
1-249-437-11
1-249-425-11
1-249-425-11
1-249-421-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
R278
R281
Remark
47K
4.7K
4.7K
2.2K
100K
5%
5%
5%
5%
5%
1-249-429-11 CARBON
1-249-429-11 CARBON
10K
10K
5%
5%
R281
1-249-425-11 CARBON
4.7K
R282
1-249-429-11 CARBON
10K
R282
1-249-425-11 CARBON
4.7K
R283
R284
R285
1-249-435-11 CARBON
1-247-791-91 CARBON
1-249-441-11 CARBON
33K
22
100K
5%
1/4W
(EXCEPT US, CND)
5%
1/4W
5%
1/4W
5%
1/4W
R286
R287
1-249-429-11 CARBON
1-249-429-11 CARBON
10K
10K
5%
5%
R287
1-249-427-11 CARBON
6.8K
R288
1-249-438-11 CARBON
56K
1/4W
1/4W
(US,CND)
5%
1/4W
(EXCEPT US, CND)
5%
1/4W
R289
R291
R292
R293
R294
1-249-437-11
1-247-863-91
1-247-863-91
1-249-417-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
47K
22K
22K
1K
100K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R295
R301
R302
R303
R304
1-247-903-00
1-249-417-11
1-249-429-11
1-249-437-11
1-249-437-11
CARBON
CARBON
CARBON
CARBON
CARBON
1M
1K
10K
47K
47K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R305
R313
R316
R318
R319
1-249-429-11
1-247-807-31
1-249-429-11
1-249-429-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
100
10K
10K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R320
R325
1-249-429-11 CARBON
1-249-427-11 CARBON
10K
6.8K
5%
5%
R325
1-249-425-11 CARBON
4.7K
R325
1-247-843-11 CARBON
3.3K
R326
1-249-425-11 CARBON
4.7K
R326
1-249-427-11 CARBON
6.8K
R326
1-249-435-11 CARBON
33K
1/4W
(E, AR, MX)
5%
1/4W
(AEP, UK, AUS, PX)
5%
1/4W (EE)
R327
R328
1-247-807-31 CARBON
1-247-807-31 CARBON
100
100
5%
5%
– 109 –
1/4W
1/4W
1/4W
1/4W
1/4W
1/4W
1/4W
(US, CND)
5%
1/4W
(EXCEPT US, CND)
5%
1/4W
(US, CND)
1/4W
1/4W
(E, AR, EE, MX)
5%
1/4W
(AUS, PX)
5%
1/4W
(AEP, UK)
5%
1/4W
1/4W
MAIN
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
R330
R331
R332
1-247-807-31 CARBON
1-247-807-31 CARBON
1-247-807-31 CARBON
100
100
100
5%
5%
5%
1/4W
1/4W
1/4W
R1507
R1521
R1522
1-249-428-11 CARBON
1-249-430-11 CARBON
1-249-426-11 CARBON
8.2K
12K
5.6K
5%
5%
5%
1/4W
1/4W
1/4W
R333
R339
R340
R341
R342
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R1524
R1525
R1526
R1527
R1531
1-249-429-11
1-249-432-11
1-249-429-11
1-249-429-11
1-247-843-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
18K
10K
10K
3.3K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R343
R344
R345
R346
R349
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R1532
R1533
R1534
R1535
R1536
1-249-411-11
1-249-427-11
1-249-429-11
1-249-425-11
1-249-425-11
CARBON
CARBON
CARBON
CARBON
CARBON
330
6.8K
10K
4.7K
4.7K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R350
R351
R352
R353
R354
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R1541
R1542
R1543
R1544
R1545
1-249-425-11
1-249-425-11
1-249-425-11
1-249-417-11
1-249-437-11
CARBON
CARBON
CARBON
CARBON
CARBON
4.7K
4.7K
4.7K
1K
47K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R355
R356
R357
R359
R360
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R1546
R1547
R1548
R1551
R1552
1-249-437-11
1-249-437-11
1-249-437-11
1-247-863-91
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
47K
47K
47K
22K
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R366
R367
R368
R369
R381
1-247-807-31
1-249-429-11
1-247-843-11
1-249-429-11
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
100
10K
3.3K
10K
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R1553
R1554
R1555
R1556
R1557
1-249-426-11
1-247-840-00
1-247-863-91
1-249-421-11
1-249-428-11
CARBON
CARBON
CARBON
CARBON
CARBON
5.6K
2.4K
22K
2.2K
8.2K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R384
R395
R396
R397
R398
1-249-429-11
1-247-807-31
1-249-435-11
1-247-807-31
1-249-435-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
100
33K
100
33K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R417
R913
R914
R915
R916
1-249-441-11
1-247-815-91
1-249-417-11
1-249-425-11
1-247-815-91
CARBON
CARBON
CARBON
CARBON
CARBON
100K
220
1K
4.7K
220
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R917
R918
R920
R921
R951
1-247-815-91
1-249-425-11
1-249-417-11
1-247-895-91
1-249-425-11
CARBON
CARBON
CARBON
CARBON
CARBON
220
4.7K
1K
470K
4.7K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R952
R1501
R1502
R1503
R1504
1-249-425-11
1-249-435-11
1-249-417-11
1-249-426-11
1-247-840-00
CARBON
CARBON
CARBON
CARBON
CARBON
4.7K
33K
1K
5.6K
2.4K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R1505
R1506
1-247-863-91 CARBON
1-249-421-11 CARBON
22K
2.2K
5%
5%
1/4W
1/4W
< VARIABLE RESISTOR >
RV1501 1-238-598-11 RES, ADJ, CARBON 2.2K
RV1551 1-238-598-11 RES, ADJ, CARBON 2.2K
< RELAY >
RY141
RY141
1-755-141-11 RELAY (US, CND)
1-515-920-11 RELAY (24V) (EXCEPT US, CND)
< TERMINAL >
TM131
1-537-240-31 TERMINAL BOARD (CHECKER PIN) (SPEAKER)
< VIBRATOR >
X301
1-760-489-11 VIBRATOR, CERAMIC (5MHz)
X302
1-567-098-41 VIBRATOR, CRYSTAL (32.768MHz)
************************************************************
– 110 –
PANEL
Ref. No.
Part No.
Description
Remark
*
A-4392-444-A PANEL BOARD, COMPLETE
**********************
*
4-978-168-01 HOLDER, FL TUBE
Ref. No.
Part No.
Description
Remark
D612
D613
D614
D616
D617
8-719-058-03
8-719-058-04
8-719-058-04
8-719-058-04
8-719-058-04
DIODE
DIODE
DIODE
DIODE
DIODE
SEL5423E-TP15 (TUNER/BAND)
SEL5223S-TP15 (ENTER/NEXT)
SEL5223S-TP15 (GROOVE)
SEL5223S-TP15 (EFFECT)
SEL5223S-TP15 (ENTER)
D618
D619
D620
D621
D622
8-719-058-04
8-719-058-04
8-719-058-04
8-719-058-04
8-719-058-04
DIODE
DIODE
DIODE
DIODE
DIODE
SEL5223S-TP15 (FILE 1)
SEL5223S-TP15 (FILE 2)
SEL5223S-TP15 (FILE 3)
SEL5223S-TP15 (FILE 4)
SEL5223S-TP15 (FILE 5)
D623
D624
D625
8-719-058-04 DIODE SEL5223S-TP15 (P.FILE)
8-719-058-04 DIODE SEL5223S-TP15 (MENU 2)
8-719-058-04 DIODE SEL5223S-TP15 (MENU 1)
< CAPACITOR >
C601
C602
C603
C604
C606
1-126-967-11
1-162-306-11
1-126-963-11
1-126-960-11
1-126-960-11
ELECT
CERAMIC
ELECT
ELECT
ELECT
47uF
0.01uF
4.7uF
1uF
1uF
20%
20%
20%
20%
20%
50V
16V
50V
50V
50V
C608
C610
C611
C621
C622
1-124-584-00
1-162-306-11
1-162-306-11
1-126-957-11
1-162-306-11
ELECT
CERAMIC
CERAMIC
ELECT
ELECT
100uF
0.01uF
0.01uF
0.22uF
0.01uF
20%
20%
20%
20%
20%
10V
16V
16V
50V
16V
C623
C624
C625
C626
C632
1-124-464-11
1-136-159-00
1-162-302-11
1-124-464-11
1-124-464-11
ELECT
ELECT
FILM
ELECT
ELECT
0.22uF
0.033uF
2200PF
0.22uF
0.22uF
20%
20%
5%
20%
20%
50V
50V
16V
50V
50V
C641
C642
C643
C644
C645
1-162-286-21
1-162-286-21
1-162-286-21
1-162-286-21
1-162-286-21
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
220
220
220
220
220
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C646
C647
C648
C649
C650
1-162-286-21
1-162-286-21
1-162-286-21
1-162-286-21
1-162-286-21
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
220
220
220
220
220
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C651
C652
C653
C654
C655
1-162-286-21
1-162-286-21
1-162-286-21
1-162-286-21
1-162-286-21
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
220
220
220
220
220
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
< FERRITE BEAD >
FB601
1-412-473-21 INDUCTOR (SMALL TYPE)
< FILTER >
FL601
1-517-619-11 INDICATOR TUBE, FLUORESCENT
< COIL >
< CONNECTOR >
* CN601
CN602
* CN603
* CN604
1-568-836-11
1-506-486-11
1-568-944-11
1-568-946-11
SOCKET, CONNECTOR 17P
PIN, CONNECTOR 7P
PIN, CONNECTOR 6P
PIN, CONNECTOR 8P
< DIODE >
D601
D602
D606
D607
D611
8-719-987-63
8-719-987-63
8-719-987-63
8-719-987-63
8-719-058-03
DIODE
DIODE
DIODE
DIODE
DIODE
1N4148M
1N4148M
1N4148M
1N4148M
SEL5423E-TP15 (TUNER/BAND)
L601
1-410-509-11 MICRO INDUCTOR 10uH
< IC >
IC601
IC602
8-759-446-26 IC TMP87CH74-6544
8-759-459-84 IC NJL56H400
< TRANSISTOR >
Q601
Q602
Q603
Q604
Q605
8-729-119-78
8-729-118-00
8-729-118-00
8-729-119-77
8-729-119-77
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC403SP-51
2SB1116-L
2SB1116-L
2SA1175-FEK
2SA1175-FEK
Q606
Q607
Q608
Q609
Q610
8-729-119-77
8-729-119-77
8-729-119-77
8-729-119-77
8-729-119-77
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SA1175-FEK
2SA1175-FEK
2SA1175-FEK
2SA1175-FEK
2SA1175-FEK
Q611
Q614
Q617
Q618
Q619
8-729-119-77
8-729-119-77
8-729-119-77
8-729-119-77
8-729-119-77
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SA1175-FEK
2SA1175-FEK
2SA1175-FEK
2SA1175-FEK
2SA1175-FEK
Q621
8-729-119-77 TRANSISTOR 2SA1175-FEK
– 111 –
PANEL
Ref. No.
Part No.
Description
Remark
< RESISTOR >
R603
R608
R609
R610
R611
1-247-903-00
1-249-429-11
1-247-843-11
1-247-843-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
1M
10K
3.3K
3.3K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R612
R613
R614
R615
R616
1-249-429-11
1-249-401-11
1-249-429-11
1-249-429-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
47
10K
10K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R617
R621
R622
R623
R624
1-249-429-11
1-249-421-11
1-249-437-11
1-247-895-91
1-249-421-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
2.2K
47K
470K
2.2K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R625
R626
R633
R634
R636
1-249-437-11
1-247-895-91
1-247-897-11
1-247-897-11
1-249-435-11
CARBON
CARBON
CARBON
CARBON
CARBON
47K
470K
560K
560K
33K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R637
R641
R642
R643
R644
1-247-895-91
1-249-427-11
1-247-815-91
1-249-410-11
1-249-412-11
CARBON
CARBON
CARBON
CARBON
CARBON
470K
6.8K
220
270
390
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R645
R646
R647
R648
R649
1-249-413-11
1-249-415-11
1-249-416-11
1-249-418-11
1-249-419-11
CARBON
CARBON
CARBON
CARBON
CARBON
470
680
820
1.2K
1.5K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R650
R651
R652
R653
R654
1-249-427-11
1-247-815-91
1-249-410-11
1-249-412-11
1-249-413-11
CARBON
CARBON
CARBON
CARBON
CARBON
6.8K
220
270
390
470
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R655
R656
R657
R658
R659
1-249-415-11
1-249-416-11
1-249-418-11
1-249-427-11
1-247-815-91
CARBON
CARBON
CARBON
CARBON
CARBON
680
820
1.2K
6.8K
220
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R660
R661
R662
R663
R664
1-249-410-11
1-249-412-11
1-249-427-11
1-247-815-91
1-249-410-11
CARBON
CARBON
CARBON
CARBON
CARBON
270
390
6.8K
220
270
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R665
R666
R667
R668
R669
1-249-412-11
1-249-413-11
1-249-415-11
1-249-416-11
1-249-418-11
CARBON
CARBON
CARBON
CARBON
CARBON
390
470
680
820
1.2K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
Ref. No.
Part No.
Description
Remark
R670
R671
R672
R673
R674
1-249-419-11
1-249-421-11
1-247-843-11
1-249-425-11
1-249-427-11
CARBON
CARBON
CARBON
CARBON
CARBON
1.5K
2.2K
3.3K
4.7K
6.8K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R675
R676
R677
R681
R682
1-249-429-11
1-249-432-11
1-249-436-11
1-249-429-11
1-249-421-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
18K
39K
10K
2.2K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R683
R684
R685
R686
R687
1-247-887-00
1-249-421-11
1-247-815-91
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
220K
2.2K
220
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R688
R689
R691
R692
R693
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R694
R695
R696
R697
R698
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R699
R700
1-247-807-31 CARBON
1-247-807-31 CARBON
100
100
5%
5%
1/4W
1/4W
< SWITCH >
S601
S602
S603
S604
S605
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
SWITCH, TACTILE (ENTER/NEXT)
SWITCH, TACTILE (TUNER MEMORY)
SWITCH, TACTILE (TUNING MODE)
SWITCH, TACTILE (TUNER/BAND)
SWITCH, TACTILE (TUNING +)
S606
S607
S608
S609
S610
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
SWITCH, TACTILE (TUNING –)
SWITCH, TACTILE (STEREO/MONO)
SWITCH, TACTILE (FUNCTION)
SWITCH, TACTILE (GROOVE)
SWITCH, TACTILE (GEQ ¢)
S611
S612
S613
S614
S616
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
SWITCH, TACTILE (GEQ ª)
SWITCH, TACTILE (GEQ ·)
SWITCH, TACTILE (GEQ ›)
SWITCH, TACTILE (DBFB)
SWITCH, TACTILE (GEQ CONTROL)
S617
S618
S619
S620
S621
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
SWITCH, TACTILE (ENTER)
SWITCH, TACTILE (EFFECT)
SWITCH, TACTILE (SPECTRUM ANALYZER)
SWITCH, TACTILE (DISPLAY/DEMO)
SWITCH, TACTILE (POWER)
S622
S623
1-554-303-21 SWITCH, TACTILE (CLOCK SET)
1-554-303-21 SWITCH, TACTILE (REC)
– 112 –
PANEL
Ref. No.
Part No.
Description
Remark
S624
S625
S626
1-554-303-21 SWITCH, TACTILE (DAILY 1)
1-554-303-21 SWITCH, TACTILE (DAILY 2)
1-554-303-21 SWITCH, TACTILE (SLEEP)
S628
S629
S630
S631
S701
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
1-473-392-11
22uF
22uF
1-130-493-00 MYLAR
1-130-493-00 MYLAR
1-104-482-11 ELECT
< VIBRATOR >
C901
1-126-974-11 ELECT
C902
1-130-777-00 FILM
C902
1-136-165-00 FILM
C951
1-104-482-11 ELECT
C951
1-126-974-11 ELECT
C952
1-130-777-00 FILM
C952
1-136-165-00 FILM
1-128-582-11 ELECT
10uF
C801
1-126-963-11 ELECT
4.7uF
C802
1-162-286-21 CERAMIC
220PF
C803
C804
C806
C807
1-162-282-31
1-126-967-11
1-126-967-11
1-128-560-11
100PF
47uF
47uF
22uF
CERAMIC
ELECT
ELECT
ELECT
100V
(US, CND)
20%
50V
(EXCEPT US, CND)
10%
50V
10%
50V
20%
50V
20%
50V
20%
100V
(EXCEPT AEP, UK, EE)
1-126-965-11 ELECT
22uF
C809
1-128-560-11 ELECT
22uF
C809
1-126-965-11 ELECT
22uF
C810
C811
C812
C814
C841
1-164-159-21
1-130-493-00
1-130-493-00
1-162-306-11
1-126-933-11
0.1uF
0.068uF
0.068uF
0.01uF
100uF
C841
1-126-925-11 ELECT
470uF
C851
1-128-582-11 ELECT
10uF
C851
1-126-963-11 ELECT
4.7uF
CERAMIC
MYLAR
MYLAR
CERAMIC
ELECT
CERAMIC
CERAMIC
ELECT
ELECT
220PF
100PF
47uF
47uF
20%
100V
(EXCEPT AEP, UK, EE)
20%
50V
(AEP, UK, EE)
0.068uF 5%
50V
0.068uF 5%
50V
4700uF 20%
63V
(US, CND)
3300uF 20%
50V
(EXCEPT US, CND)
0.1uF
10%
100V
(US, CND)
0.1uF
5%
50V
(EXCEPT US, CND)
4700uF 20%
63V
(US, CND)
3300uF 20%
50V
(EXCEPT US, CND)
0.1uF
10%
100V
(US, CND)
20%
C807
1-162-286-21
1-162-282-31
1-126-967-11
1-126-967-11
1-128-560-11 ELECT
C861
C862
C901
C801
Remark
C857
1-126-965-11 ELECT
< CAPACITOR >
C852
C853
C854
C856
Description
C857
A-4392-442-A POWER AMP BOARD, COMPLETE (US, CND)
A-4392-460-A POWER AMP BOARD, COMPLETE
(E, AR, MX, AUS, PX)
A-4392-465-A POWER AMP BOARD, COMPLETE (AEP, UK, EE)
**************************
*
Part No.
SWITCH, TACTILE (WAVE)
SWITCH, TACTILE (KARAOKE PON/MPX)
SWITCH, TACTILE (SURROUND)
SWITCH, TACTILE (P FILE MEMORY)
ENCODER, ROTARY (VOLUME)
X601
1-579-125-11 VIBRATOR, CERAMIC (8 MHz)
************************************************************
*
*
Ref. No.
POWER AMP
20%
50V
(AEP, UK, EE)
20%
100V
(EXCEPT AEP, UK, EE)
20%
50V
(AEP, UK, EE)
5%
5%
20%
20%
50V
50V
50V
16V
10V
(US, CND)
20%
10V
(EXCEPT US, CND)
20%
100V
(US, CND)
20%
50V
(EXCEPT US, CND)
10%
10%
20%
20%
50V
50V
50V
50V
0.1uF
5%
50V
(EXCEPT US, CND)
< CONNECTOR >
CN801
1-778-981-11 CONNECTOR, BOARD TO BOARD 13P
< DIODE >
D801
D801
D841
D842
D851
8-719-815-85
8-719-987-63
8-719-987-63
8-719-987-63
8-719-815-85
DIODE
DIODE
DIODE
DIODE
DIODE
1S1585 (EXCEPT AEP, UK, EE)
1N4148M (AEP, UK, EE)
1N4148M
1N4148M
1S1585 (EXCEPT AEP, UK, EE)
D851
D901
D901
8-719-987-63 DIODE 1N4148M (AEP, UK, EE)
8-719-510-68 DIODE D5SBA20F01 (EXCEPT AEP, UK, EE)
8-719-028-23 DIODE D3SBA20-4101 (AEP, UK, EE)
< IC >
IC801
IC801
IC801
8-749-921-68 IC STK-4231MK2 (US, CND)
8-749-900-34 IC STK-4182MK2 (E, AR, MX, AUS, PX)
8-749-920-10 IC STK4172MK2 (AEP, UK, EE)
< TRANSISTOR >
Q801
Q851
8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
< RESISTOR >
R801
R802
R803
– 113 –
1-249-417-11 CARBON
1-249-437-11 CARBON
1-249-413-11 CARBON
1K
47K
470
5%
5%
5%
1/4W
1/4W
1/4W
(US, CND)
POWER AMP
Ref. No.
Part No.
TABLE SENSOR
Description
TC-A SW
Remark
Ref. No.
Part No.
1-208-601-11 WIREWOUND
1-260-076-11 CARBON
Description
Remark
R803
1-249-415-11 CARBON
680
5%
1/4W
(EXCEPT, US, CND)
! R858
R859
R804
R805
1-249-437-11 CARBON
1-260-107-11 CARBON
47K
4.7K
5%
5%
R805
1-260-105-11 CARBON
3.3K
R861
1-249-417-11 CARBON
1K
5%
1/4W
R862
1-247-863-91 CARBON
22K
5%
1/4W
R863
1-249-441-11 CARBON
100K
5%
1/4W
************************************************************
R806
1-260-107-11 CARBON
4.7K
1/4W
1/2W
(US, CND)
5%
1/2W
(EXCEPT US, CND)
5%
1/2W
(US, CND)
*
1-659-058-13 TABLE SENSOR BOARD
******************
R806
1-260-105-11 CARBON
3.3K
*
4-980-385-01 HOLDER (SW)
1-212-881-11 FUSIBLE
1-208-601-11 WIREWOUND
1-260-076-11 CARBON
100
0.1
10
5%
1/2W
(EXCEPT US, CND)
5%
1/4W
F
10%
2W
F
5%
1/2W
R811
R812
R813
R814
1-249-417-11
1-247-863-91
1-249-441-11
1-260-105-11
1K
22K
100K
3.3K
5%
5%
5%
5%
R814
1-260-099-11 CARBON
1K
R816
1-260-105-11 CARBON
3.3K
R816
1-260-099-11 CARBON
1K
! R820
R841
1-202-972-61 FUSIBLE
1-249-429-11 CARBON
1
10K
1/2W
(US, CND)
5%
1/2W
(EXCEPT US, CND)
5%
1/4W
F
5%
1/4W
R842
1-247-885-00 CARBON
180K
5%
R842
1-247-881-00 CARBON
120K
R843
1-247-843-11 CARBON
3.3K
R843
1-249-421-11 CARBON
2.2K
R844
R851
R852
R853
1-249-429-11
1-249-417-11
1-249-437-11
1-249-413-11
CARBON
CARBON
CARBON
CARBON
10K
1K
47K
470
R853
1-249-415-11 CARBON
680
R854
R855
1-249-437-11 CARBON
1-260-107-11 CARBON
47K
4.7K
R855
1-260-105-11 CARBON
3.3K
R856
1-260-107-11 CARBON
4.7K
R856
1-260-105-11 CARBON
3.3K
! R857
1-212-881-11 FUSIBLE
100
! R807
! R808
R809
CARBON
CARBON
CARBON
CARBON
The components identified by
mark ! or dotted line with
mark ! are critical for safety.
Replace only with part number
specified.
1/4W
1/4W
1/4W
1/2W
(US, CND)
5%
1/2W
(EXCEPT US, CND)
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
(US, CND)
5%
1/4W
(EXCEPT US, CND)
5%
5%
1/4W
1/2W
(US, CND)
5%
1/2W
(EXCEPT US, CND)
5%
1/2W
(US, CND)
IC202
2W
1/2W
8-749-924-18 IC PHOTO INTERRUPTER RPI-1391
< RESISTOR >
R207
1-249-416-11 CARBON
820
5%
1/4W
************************************************************
1-664-012-11 TC-A SW BOARD
*************
*
< CONNECTOR >
* CN612
1-568-943-11 PIN, CONNECTOR 5P
< DIODE >
D631
D632
8-719-057-10 DIODE LNJ301MPUJA (·)
8-719-057-10 DIODE LNJ301MPUJA (ª)
< RESISTOR >
R705
R706
R707
R708
R709
1-249-413-11
1-249-415-11
1-249-416-11
1-249-418-11
1-249-419-11
CARBON
CARBON
CARBON
CARBON
CARBON
470
680
820
1.2K
1.5K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R710
R711
R714
1-249-421-11 CARBON
1-247-807-31 CARBON
1-247-807-31 CARBON
2.2K
100
100
5%
5%
5%
1/4W
1/4W
1/4W
< SWITCH >
S641
S642
S643
S644
S645
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
SWITCH, TACTILE (·)
SWITCH, TACTILE (ª)
SWITCH, TACTILE (p)
SWITCH, TACTILE (0)
SWITCH, TACTILE ())
S646
1-554-303-21 SWITCH, TACTILE (DOLBY NR)
S647
1-554-303-21 SWITCH, TACTILE (DIRECTION)
************************************************************
5%
1/2W
(EXCEPT US, CND)
5%
1/4W
F
Les composants identifiés par une
marque ! sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le neméro spécifié.
10%
5%
< IC >
5%
1/4W
(US, CND)
5%
1/4W
(EXCEPT US, CND)
5%
1/4W
(US, CND)
5%
1/4W
(EXCEPT US, CND)
0.1
10
– 114 –
F
TC-B SW
Ref. No.
Part No.
*
1-664-013-11 TC-B SW BOARD
*************
D635
D636
D637
D638
8-719-057-10
8-719-057-10
8-719-058-17
8-719-057-09
Description
Remark
Ref. No.
Part No.
Description
1-162-306-11 CERAMIC
C5
1-163-031-11 CERAMIC
< DIODE >
C6
1-162-306-11 CERAMIC
DIODE
DIODE
DIODE
DIODE
C6
1-163-038-91 CERAMIC
C7
1-101-004-00 CERAMIC
C8
1-162-306-11 CERAMIC
C8
1-163-031-11 CERAMIC
C9
1-162-306-11 CERAMIC
C9
1-163-031-11 CERAMIC
C10
1-163-031-11 CERAMIC
C11
1-164-159-21 CERAMIC
C12
1-162-198-31 CERAMIC
C14
1-162-306-11 CERAMIC
C16
1-163-038-91 CERAMIC
C19
C21
1-163-249-11 CHIP CERAMIC
1-102-514-11 CERAMIC
C21
1-163-141-00 CERAMIC CHIP
C22
1-163-031-11 CERAMIC
C22
1-164-159-21 CERAMIC
C23
1-162-306-11 CERAMIC
0.01uF
C23
1-163-235-11 CHIP CERAMIC
22PF
C24
1-126-967-11 ELECT
47uF
C24
1-163-239-11 CHIP CERAMIC
33PF
C25
1-162-306-11 CERAMIC
C26
1-126-964-11 ELECT
C26
1-126-967-11 ELECT
C27
1-164-159-21 CERAMIC
C28
1-126-961-11 ELECT
< RESISTOR >
R715
R716
R717
R718
R719
1-249-421-11
1-247-843-11
1-249-425-11
1-249-427-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
2.2K
3.3K
4.7K
6.8K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R720
R721
R722
R724
R725
1-249-432-11
1-249-436-11
1-247-881-00
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
18K
39K
120K
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R727
R728
1-247-807-31 CARBON
1-247-807-31 CARBON
100
100
5%
5%
1/4W
1/4W
< SWITCH >
S651
S652
S653
S654
S655
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
1-554-303-21
SWITCH, TACTILE (·)
SWITCH, TACTILE (ª)
SWITCH, TACTILE ())
SWITCH, TACTILE (0)
SWITCH, TACTILE (p)
S656
1-554-303-21 SWITCH, TACTILE (P)
S657
1-554-303-21 SWITCH, TACTILE (r REC)
S658
1-554-303-21 SWITCH, TACTILE (H.SPEED DUBB)
S659
1-554-303-21 SWITCH, TACTILE (CD SYNC)
************************************************************
A-4303-510-A
A-4303-512-A
A-4303-570-A
A-4303-576-A
*
*
*
*
Remark
C5
LNJ301MPUJA (ª)
LNJ301MPUJA (·)
LNJ401NPYJA (P)
LNJ801LPDJA (r REC)
TCB BOARD,COMPLETE (US, CND)
TCB BOARD,COMPLETE (E, AR, MX, AUS, PX)
TCB BOARD,COMPLETE (EE)
TCB BOARD,COMPLETE (AEP, UK)
******************
0.01uF
20%
16V
(EXCEPT AEP, UK, EE)
10000PF
50V
(2012) (AEP, UK, EE)
0.01uF 20%
16V
(EXCEPT AEP, UK, EE)
100000PF
25V
(2012) (AEP, UK, EE)
0.01uF
50V
(EXCEPT AEP, UK)
0.01uF 20%
16V
(EXCEPT AEP, UK, EE)
10000PF
50V
(2012) (AEP, UK, EE)
0.01uF
20%
16V
(EXCEPT AEP, UK, EE)
10000PF
50V
(2012) (AEP, UK, EE)
10000PF
50V
(2012) (AEP, UK, EE)
0.1uF
50V
(EXCEPT AEP, UK, EE)
8.2PF
10%
50V
(EXCEPT AEP, UK, EE)
0.01uF 20%
16V
(EXCEPT AEP, UK, EE)
100000PF
25V
(2012) (AEP, UK, EE)
82PF (2012) (AEP, UK, EE)
22PF
5%
50V
(EXCEPT AEP, UK, EE)
0.001uF 5%
50V
(AEP, UK, EE)
10000PF
50V
(2012) (AEP, UK, EE)
0.1uF
50V
(EXCEPT AEP, UK, EE)
< CAPACITOR >
C1
1-163-141-00 CERAMIC CHIP
C1
1-162-294-31 CERAMIC
C2
1-126-967-11 ELECT
C3
1-163-038-91 CERAMIC
C3
1-164-159-21 CERAMIC
0.001uF 5%
50V
(AEP, UK, EE)
0.001uF 10%
50V
(EXCEPT AEP, UK, EE)
47uF
20%
16V
100000PF
25V
(2012) (AEP, UK, EE)
0.1uF
50V
(EXCEPT AEP, UK, EE)
– 115 –
TCB
20%
16V
(EXCEPT AEP, UK, EE)
5%
50V
(2012) (AEP, UK, EE)
20%
16V
(EXCEPT AEP, UK, EE)
5%
50V
(2012) (AEP,UK, EE)
0.01uF 20%
16V
(EXCEPT AEP, UK, EE)
10uF
20%
50v
(EXCEPT AEP, UK, EE)
47uF
20%
16V
(AEP, UK, EE)
0.1uF
50V
(EXCEPT AEP, UK, EE)
2.2uF
20%
50V
(EXCEPT AEP, UK, EE)
TCB
Ref. No.
Part No.
Description
C28
1-126-967-11 ELECT
C29
1-102-518-11 CERAMIC
C29
1-162-306-11 CERAMIC
C30
1-126-961-11 ELECT
C30
1-162-294-31 CERAMIC
C31
1-162-306-11 CERAMIC
C31
1-163-031-11 CERAMIC
C32
1-163-038-91 CERAMIC
C33
1-163-038-91 CERAMIC
C34
1-163-229-11 CHIP CERAMIC
C35
1-163-038-91 CERAMIC
C36
1-163-141-00 CERAMIC CHIP
C37
1-163-141-00 CERAMIC CHIP
C39
1-163-141-00 CERAMIC CHIP
C40
1-163-031-11 CERAMIC
C41
1-126-933-11 ELECT
C41
1-163-031-11 CERAMIC
C42
1-162-306-11 CERAMIC
C42
1-163-038-91 CERAMIC
C43
1-126-962-11 ELECT
C43
1-163-038-91 CERAMIC
C44
1-162-306-11 CERAMIC
C44
1-163-031-11 CERAMIC
C45
1-124-589-11 ELECT
C45
1-163-038-91 CERAMIC
C46
1-162-600-11 CERAMIC
C46
1-163-077-00 CERAMIC CHIP
Remark
47uF
20%
Ref. No.
Part No.
Description
Remark
16V
(AEP, UK, EE)
33PF
5%
50V
(EXCEPT AEP, UK, EE)
0.01uF 20%
16V
(AEP, UK, EE)
C47
1-126-967-11 ELECT
C47
1-162-294-31 CERAMIC
C48
1-126-160-11 ELECT
2.2uF
50V
(AEP, UK, EE)
0.001uF 10%
50V
(EXCEPT AEP, UK, EE)
0.01uF 20%
16V
(EXCEPT AEP, UK, EE)
C48
1-163-031-11 CERAMIC
C49
1-126-959-11 ELECT
C49
1-136-159-00 METALIZED FILM
10000PF
50V
(2012) (AEP, UK, EE)
100000PF
25V
(2012) (AEP, UK, EE)
100000PF
25V
(2012) (AEP, UK, EE)
C49
1-136-162-00 METALIZED FILM 0.056uF 5%
12PF
5%
50V
(2012) (AEP, UK, EE)
100000PF
25V
(2012) (AEP, UK ,EE)
0.001uF 5%
50V
(AEP, UK, EE)
C50
1-136-162-00 METALIZED FILM 0.056uF 5%
C51
1-126-960-11 ELECT
C51
1-162-600-11 CERAMIC
0.001uF 5%
C52
1-126-963-11 ELECT
C52
1-162-600-11 CERAMIC
C53
C54
1-126-964-11 ELECT
1-104-396-11 ELECT
C54
1-126-157-11 ELECT
10uF
C55
1-104-396-11 ELECT
10uF
C55
1-126-964-11 ELECT
10uF
C56
1-104-396-11 ELECT
10uF
C56
1-126-964-11 ELECT
C57
1-163-017-00 CERAMIC CHIP
C57
1-164-159-21 CERAMIC
C58
1-162-306-11 CERAMIC
C58
1-163-017-00 CERAMIC CHIP
C59
1-163-809-11 CERAMIC CHIP
C59
C59
1-163-989-11 CERAMIC CHIP
1-164-159-21 CERAMIC
20%
50V
(AEP, UK, EE)
0.001uF 5%
50V
(AEP, UK, EE)
10000PF
50V
(2012) (AEP, UK, EE)
20%
10V
(EXCEPT AEP, UK, EE)
10000PF
50V
(2012) (AEP, UK, EE)
0.01uF 20%
16V
(EXCEPT AEP, UK, EE)
C50
C50
47uF
20%
16V
(AEP, UK, EE)
0.001uF 10%
50V
(EXCEPT AEP, UK, EE)
1uF
20%
50V
(EXCEPT AEP, UK, EE)
10000PF
50V
(2012) (AEP, UK, EE)
0.47uF 20%
50V
(AEP, UK, EE)
0.033uF 5%
16V
(E, AR, MX, AUS, PX)
16V
(US, CND)
1-126-960-11 ELECT
1.0uF
20%
50V
(AEP, UK, EE)
1-136-159-00 METALIZED FILM 0.033uF 5%
16V
(E, AR, MX, AUS, PX)
16V
(US, CND)
1.0uF
20%
50V
(AEP, UK, EE)
4700PF 10%
16V
(EXCEPT AEP, UK, EE)
4.7uF
20%
50V
(AEP, UK, EE)
4700PF 10%
50V
(EXCEPT AEP, UK, EE)
10uF
20%
50v
10uF
20%
16V
(AEP, UK, EE)
100uF
100000PF
25V
(2012) (AEP, UK, EE)
3.3uF
20%
50V
(EXCEPT AEP, UK, EE)
100000PF
25V
(2012) (AEP, UK, EE)
20%
16V
(EXCEPT AEP, UK, EE)
10000PF
50V
(2012) (AEP, UK, EE)
47uF
20%
16V
(EXCEPT AEP, UK, EE)
20%
16V
(EXCEPT AEP, UK, EE)
20%
16V
(AEP, UK, EE)
20%
50V
(EXCEPT AEP, UK, EE)
20%
16V
(AEP, UK, EE)
10uF
20%
50v
(EXCEPT AEP, UK, EE)
0.0047uF 5%
50V
(AEP, UK, EE)
0.01uF
100000PF
25V
(2012) (AEP, UK, EE)
4700PF 10%
16V
(EXCEPT AEP, UK, EE)
0.1uF
10%
25V
(AEP, UK, EE)
– 116 –
0.1uF
50V
(EXCEPT AEP, UK, EE)
0.01uF 20%
16V
(EXCEPT AEP, UK, EE)
0.0047uF 5%
50V
(AEP, UK, EE)
0.047uF 10%
25V
(AEP, UK)
0.033uF 10%
25V (EE)
0.1uF
50V
(EXCEPT AEP, UK, EE)
TCB
Ref. No.
Part No.
Description
C60
1-163-809-11 CERAMIC CHIP
C60
C61
1-163-989-11 CERAMIC CHIP
1-126-301-11 ELECT
C61
1-164-159-21 CERAMIC
C62
1-126-967-11 ELECT
C62
1-163-141-00 CERAMIC CHIP
C63
1-163-017-00 CERAMIC CHIP
C63
1-164-159-21 CERAMIC
C64
1-126-959-11 ELECT
C64
1-126-967-11 ELECT
C65
1-126-960-11 ELECT
C65
1-163-031-11 CERAMIC
C66
1-126-162-11 ELECT
C66
1-126-960-11 ELECT
C67
1-126-933-11 ELECT
Remark
Ref. No.
Part No.
Description
Remark
0.047uF 10%
25V
(AEP, UK)
0.033uF 10%
25V (EE)
1uF
20%
50V
(AEP, UK, EE)
C1706
C1712
C1713
C1714
C1715
1-126-960-11
1-130-736-11
1-130-736-11
1-126-960-11
1-126-960-11
ELECT
PP FILM
PP FILM
ELECT
ELECT
1.0uF
0.01uF
0.01uF
1.0uF
1.0uF
20%
5%
5%
20%
20%
50V (EE)
16V (EE)
16V (EE)
50V (EE)
50V (EE)
0.1uF
C1716
C1719
C1725
C1726
C1727
1-126-960-11
1-126-967-11
1-126-967-11
1-126-960-11
1-126-960-11
ELECT
ELECT
ELECT
ELECT
ELECT
1.0uF
47uF
47uF
1.0uF
1.0uF
20%
20%
20%
20%
20%
50V (EE)
16V (EE)
16V (EE)
50V (EE)
50V (EE)
C1728
1-126-966-11 ELECT
33uF
20%
16V (EE)
50V
(EXCEPT AEP, UK, EE)
47uF
20%
16V
(EXCEPT AEP, UK, EE)
0.001uF 5%
50V
(AEP, UK, EE)
0.0047uF 5%
50V
(AEP,UK,EE)
0.1uF
50V
(EXCEPT AEP, UK, EE)
0.47uF 20%
50V
(EXCEPT AEP, UK, EE)
47uF
16V
(AEP, UK, EE)
1.0uF
20%
50V
(EXCEPT AEP, UK, EE)
10000PF
50V
(2012) (AEP, UK, EE)
3.3uF
20%
50V
(AEP, UK, EE)
1.0uF
20%
50V
(EXCEPT AEP, UK, EE)
100uF 20%
10V
(AEP, UK, EE)
< FILTER >
CF1
CF1
CF2
CF2
CF3
FILTER, CERAMIC (EXCEPT AEP, UK)
FILTER, CERAMIC (AEP, UK)
FILTER, CERAMIC (EXCEPT AEP, UK, EE)
FILTER, CERAMIC (AEP, UK)
FILTER, CERAMIC (AEP, UK)
< CONNECTOR >
CN1
1-568-832-11 SOCKET, CONNECTOR 13P
CN1
(EXCEPT AEP, UK, EE)
1-568-834-11 SOCKET, CONNECTOR 15P (AEP, UK, EE)
20%
C67
1-126-964-11 ELECT
10uF
20%
50v
(EXCEPT AEP, UK, EE)
0.01uF 20%
16V
0.01uF 20%
16V
(EXCEPT AEP, UK, EE)
0.01uF 20%
16V
(EXCEPT AEP, UK, EE)
C68
C69
1-162-306-11 CERAMIC
1-162-306-11 CERAMIC
C70
1-162-306-11 CERAMIC
C71
C72
1-162-306-11 CERAMIC
1-126-967-11 ELECT
C73
1-162-306-11 CERAMIC
C74
1-126-964-11 ELECT
C120
1-163-105-00 CERAMIC CHIP
C1702
1-130-014-00 PP FILM
20%
50v
(EXCEPT AEP, UK, EE)
33PF
5%
50V
(AEP, UK, EE)
470PF 5%
16V (EE)
C1703
1-126-959-11 ELECT
0.47uF
C1704
1-126-959-11 ELECT
C1705
1-163-035-00 CERAMIC CHIP
< TRIMMER >
CT1701 1-141-444-11 CAP, CERAMIC TRIMMER 50PF (EE)
< DIODE >
D1
D2
D21
D41
20%
20%
16V
16V
(AEP, UK, EE)
0.01uF 20%
16V
(EXCEPT AEP, UK, EE)
8-719-933-33
8-719-987-63
8-719-976-XX
8-719-016-74
DIODE
DIODE
DIODE
DIODE
UZL-6L1-TA (EXCEPT AEP, UK, EE)
1N4148M-TA (EXCEPT AEP, UK, EE)
UDZ-TE-17-5.1B (AEP, UK, EE)
1SS352-TPH3 (AEP, UK, EE)
< FRONTEND >
FE1
0.01uF
47uF
1-567-389-11
1-579-374-71
1-567-389-11
1-760-393-11
1-760-393-11
FE1
FE1
FE2
FE2
1-233-533-11 ENCAPSULATED COMPONENT
(EXCEPT AEP, UK, EE)
1-693-335-11 FRONT END (3 GANG) (EE)
1-693-357-11 FRONT END (4 GANG) (AEP, UK)
1-233-514-11 ENCAPSULATED COMPONENT (AEP, UK, EE)
1-239-260-11 ENCAPSULATED COMPONENT
(EXCEPT AEP, UK, EE)
10uF
20%
50V
(AEP, UK, EE)
0.47uF 20%
50V
(AEP, UK, EE)
0.047uF
50V (EE)
< IC >
IC1
IC2
IC21
IC41
IC1701
8-759-288-54
8-759-176-03
8-759-288-54
8-759-176-03
8-759-063-04
IC1702
8-759-140-53 IC MC14053BCP (EE)
– 117 –
IC
IC
IC
IC
IC
LC72130 (EXCEPT AEP, UK, EE)
LA1835 (EXCEPT AEP, UK, EE)
LC72130 (AEP, UK, EE)
LA1835 (AEP, UK, EE)
IR3R42 (EE)
TCB
Ref. No.
Part No.
Description
Remark
< IFT >
IFT41
Ref. No.
Q5
Q5
JR2
JR6
JR8
JR9
JR45
1-216-295-91
1-216-295-91
1-216-295-91
1-216-295-91
1-216-295-91
CONDUCTOR, CHIP (2012) (AEP, UK, EE)
CONDUCTOR, CHIP (2012) (AEP, UK, EE)
CONDUCTOR, CHIP (2012) (AEP, UK, EE)
CONDUCTOR, CHIP (2012) (AEP, UK, EE)
CONDUCTOR, CHIP (2012) (AEP, UK, EE)
JR46
JR47
JR48
JR49
JR51
1-216-296-91
1-216-295-91
1-216-295-91
1-216-296-91
1-216-295-91
CONDUCTOR, CHIP (3216) (AEP, UK, EE)
CONDUCTOR, CHIP (2012) (AEP, UK, EE)
CONDUCTOR, CHIP (2012) (AEP, UK, EE)
CONDUCTOR, CHIP (3216) (AEP, UK, EE)
CONDUCTOR, CHIP (2012) (AEP, UK, EE)
JR52
JR53
JR54
1-216-295-91 CONDUCTOR, CHIP (2012) (AEP, UK, EE)
1-216-296-91 CONDUCTOR, CHIP (3216) (AEP, UK, EE)
1-216-295-91 CONDUCTOR, CHIP (2012) (AEP, UK, EE)
Description
Remark
Q9
Q11
8-729-421-22 TRANSISTOR MUN2211T1 (AEP, UK, EE)
8-729-422-57 TRANSISTOR BN1A4M-TP
(EXCEPT AEP, UK, EE)
8-729-216-22 TRANSISTOR 2SA812-T1-M5M6 (AEP, UK, EE)
8-729-424-08 TRANSISTOR MUN2111T1 (AEP, UK, EE)
Q12
Q13
Q14
Q1702
8-729-424-08
8-729-424-08
8-729-424-08
8-729-907-00
1-409-636-11 TRANSFORMER,IF (CERAMIC FILTER)
< JUMPER RESISTOR >
Part No.
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
MUN2111T1 (AEP, UK, EE)
MUN2111T1 (AEP, UK, EE)
MUN2111T1 (AEP, UK, EE)
RT1N141M-TP-1 (EE)
< RESISTOR >
R1
R2
1-249-401-11 CARBON
1-216-037-00 METAL CHIP
47
330
R2
1-249-411-11 CARBON
330
R3
1-216-037-00 METAL CHIP
330
R3
1-249-411-11 CARBON
330
R5
1-216-037-00 METAL CHIP
330
R5
1-249-411-11 CARBON
330
R6
1-216-081-00 METAL CHIP
22K
R6
1-247-863-91 CARBON (SMALL) 22K
R7
1-216-037-00 METAL CHIP
330
R7
1-249-411-11 CARBON
330
R8
1-216-037-00 METAL CHIP
330
R8
1-249-411-11 CARBON
330
R9
1-216-081-00 METAL CHIP
22K
R9
1-247-863-91 CARBON (SMALL) 22K
R10
1-216-037-00 METAL CHIP
330
R10
1-249-411-11 CARBON
330
R11
1-216-081-00 METAL CHIP
22K
R11
1-247-863-91 CARBON (SMALL) 22K
R12
1-216-037-00 METAL CHIP
330
R12
1-249-411-11 CARBON
330
< JUMPER RESISTOR >
JW4
JW5
1-249-413-11 CARBON
1-249-413-11 CARBON
470 5%
470 5%
1/4W (AEP, UK)
1/4W (AEP, UK)
< COIL >
L2
L3
L4
L41
L41
1-414-142-11
1-410-521-11
1-410-515-11
1-407-500-00
1-410-119-11
INDUCTOR, MICRO 1uH (AEP, UK)
INDUCTOR, MICRO 100uH (AEP, UK, EE)
INDUCTOR, MICRO 33uH (AEP, UK)
MICRO INDUCTOR 4.7mH (AEP, UK, EE)
MICRO INDUCTOR (EL TYPE) 1mH
(EXCEPT AEP, UK, EE)
L1701
1-409-497-11 COIL (FILTER) (EE)
< FILTER >
LPF41
LPF42
1-239-845-11 FILTER, LOW PASS
1-239-845-11 FILTER, LOW PASS
< TRANSISTOR >
Q1
Q1
Q2
Q2
Q3
Q3
Q4
Q4
8-729-201-27 TRANSISTOR 2SC2715Y-TE85L (AEP, UK, EE)
8-729-230-XX TRANSISTOR 2SC2669OY-TPE4
(EXCEPT AEP, UK, EE)
8-729-201-27 TRANSISTOR 2SC2715Y-TE85L (AEP, UK, EE)
8-729-230-XX TRANSISTOR 2SC2669OY-TPE4
(EXCEPT AEP, UK, EE)
8-729-201-27 TRANSISTOR 2SC2715Y-TE85L (AEP, UK, EE)
8-729-230-XX TRANSISTOR 2SC2669OY-TPE4
(EXCEPT AEP, UK, EE)
8-729-201-27 TRANSISTOR 2SC2715Y-TE85L (AEP, UK, EE)
8-729-230-XX TRANSISTOR 2SC2669OY-TPE4
(EXCEPT AEP, UK, EE)
– 118 –
5%
5%
1/4W
1/10W
(AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/10W
(AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/10W
(AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/10W
(AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/10W
(AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/10W
(AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/10W
(AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/10W
(AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/10W
(AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/10W
(AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
TCB
Ref. No.
Part No.
Description
Remark
R13
1-216-037-00 METAL CHIP
330
R13
1-249-411-11 CARBON
330
R14
1-216-081-00 METAL CHIP
22K
R14
1-247-863-91 CARBON (SMALL) 22K
R15
1-249-429-11 CARBON
10K
R16
1-249-437-11 CARBON
47K
R18
1-216-073-00 METAL CHIP
10K
R19
1-216-073-00 METAL CHIP
10K
R19
1-249-399-11 CARBON
33
R21
1-216-049-91 CHIP
1.0K
R21
1-247-807-31 CARBON (SMALL) 100
R21
1-249-417-11 CARBON
1K
R22
1-216-049-91 CHIP
1.0K
R22
R22
1-249-417-11 CARBON
1-249-425-11 CARBON
1K
4.7K
R23
1-216-049-91 CHIP
1.0K
R23
R23
1-249-417-11 CARBON
1-249-425-11 CARBON
1K
4.7K
R24
1-216-025-91 CHIP
100
R24
1-249-425-11 CARBON
4.7K
R25
1-247-807-31 CARBON (SMALL) 100
R25
1-249-417-11 CARBON
1K
R26
1-249-411-11 CARBON
330
R26
1-249-437-11 CARBON
47K
R27
1-249-425-11 CARBON
4.7K
R27
1-249-429-11 CARBON
10K
R28
1-249-417-11 CARBON
1K
R28
1-247-843-11 CARBON (SMALL) 3.3K
5%
Ref. No.
Part No.
Description
Remark
1/10W
(AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/10W
(AEP, UK, EE)
R29
1-216-061-00 METAL CHIP
3.3K
R29
1-249-417-11 CARBON
1K
R30
1-216-186-00 CHIP
330
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
R30
1-249-417-11 CARBON
1K
R31
1-216-025-91 CHIP
100
R31
1-249-417-11 CARBON
1K
1/10W
(AEP, UK, EE)
5%
1/10W
(AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
R32
1-249-417-11 CARBON
1K
R32
1-249-425-11 CARBON
4.7K
R33
1-247-807-31 CARBON (SMALL) 100
5%
1/10W
(2012) (AEP, UK)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/4W (EE)
R33
1-249-425-11 CARBON
4.7K
R34
1-216-065-00 METAL CHIP
4.7K
R34
1-249-429-11 CARBON
10K
R35
1-216-214-00 CHIP
4.7K
R35
1-249-429-11 CARBON
10K
R36
1-216-025-91 CHIP
100
R36
1-249-437-11 CARBON
47K
R37
1-216-073-00 METAL CHIP
10K
R37
1-249-417-11 CARBON
1K
R38
1-216-089-91 CHIP
47K
R39
1-249-429-11 CARBON
10K
R41
1-249-429-11 CARBON
10K
R42
1-216-073-00 METAL CHIP
10K
R43
1-216-042-00 METAL CHIP
510
R43
1-247-843-11 CARBON (SMALL) 3.3K
R44
1-216-013-00 METAL CHIP
R44
1-247-843-11 CARBON (SMALL) 3.3K
5%
5%
1/10W
(2012) (AEP, UK)
5%
1/4W (EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/10W
(2012) (AEP, UK)
5%
1/4W (EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/10W
(2012) (AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
1/4W
(AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/4W
(AEP, UK, EE)
5%
1/10W
(AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/8W
(3216) (AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/10W
(2012) (AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/4W
(AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/4W
(AEP, UK, EE)
5%
1/10W
(AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/8W
(3216) (AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/10W
(2012) (AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/10W
(AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/10W
(2012) (AEP, UK, EE)
5%
1/4W
(AEP, UK, EE)
5%
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/4W
(AEP, UK, EE)
5%
1/4W
(AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
– 119 –
33
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/10W
(AEP, UK, EE)
5%
1/10W
(AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/10W
(AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
TCB
Ref. No.
TRANS
Part No.
Description
Remark
R45
1-247-843-11 CARBON (SMALL) 3.3K
5%
R46
1-216-073-00 METAL CHIP
10K
5%
R46
1-249-442-11 CARBON
510
R47
1-216-097-91 CHIP
100K
R47
1-249-399-11 CARBON
33
R48
1-247-843-11 CARBON (SMALL) 3.3K
R48
1-249-417-11 CARBON
1K
R49
1-216-049-91 CHIP
1.0K
R49
1-249-393-11 CARBON
10
R50
1-216-065-00 METAL CHIP
4.7K
R50
1-249-429-11 CARBON
10K
R51
1-216-065-00 METAL CHIP
4.7K
R51
1-249-441-11 CARBON
100K
R52
1-249-429-11 CARBON
10K
R53
1-249-425-11 CARBON
4.7K
R53
1-249-429-11 CARBON
10K
R54
1-249-425-11 CARBON
4.7K
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/4W
(AEP, UK, EE)
1-216-073-00 METAL CHIP
10K
5%
R99
R1702
R1703
1-249-399-11 CARBON
1-216-085-00 METAL CHIP
1-216-069-00 METAL CHIP
33
33K
6.8K
5%
5%
5%
1/10W
(AEP, UK, EE)
1/4W
1/10W (EE)
1/10W (EE)
R1704
R1708
R1711
R1714
R1715
1-216-075-00
1-216-095-00
1-249-429-11
1-216-067-00
1-216-067-00
12K
82K
10K
5.6K
5.6K
5%
5%
5%
5%
5%
1/10W (EE)
1/10W (EE)
1/4W (EE)
1/10W (EE)
1/10W (EE)
R1718
R1720
1-249-429-11 CARBON
1-249-434-11 CARBON
10K
27K
5%
5%
1/4W (EE)
1/4W (EE)
The components identified by
mark ! or dotted line with
mark ! are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque ! sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le neméro spécifié.
Remark
1-238-600-11
1-238-601-11
1-238-600-11
1-238-601-11
1-238-600-11
ADJ, CARBON 10K (EXCEPT AEP, UK, EE)
ADJ, CARBON 22K (AEP, UK, EE)
ADJ, CARBON 10K (AEP, UK, EE)
ADJ, CARBON 22K (EXCEPT AEP, UK, EE)
ADJ, CARBON 10K (AEP, UK, EE)
RV1702 1-238-599-11 ADJ, CARBON 4.7K (EE)
< TERMINAL >
TM1
TM1
1-537-238-21 TERMINAL BOARD (EXCEPT AEP, UK, EE)
1-537-488-11 TERMINAL BOARD (ANT) (AEP, UK, EE)
< VIBRATOR >
5%
1/10W
(2012) (AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/10W
(AEP, UK, EE)
R92
METAL CHIP
METAL CHIP
CARBON
METAL CHIP
METAL CHIP
RV41
RV41
RV42
RV42
RV1701
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/4W
(AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/10W
(AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
Description
< VARIABLE RESISTOR >
1/10W
(AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
5%
1/10W
(2012) (AEP, UK, EE)
R91
R56
Part No.
1/4W
(AEP, UK, EE)
5%
1/4W
(EXCEPT AEP, UK, EE)
1-216-162-00 CHIP 33
5%
1/8W (3216)
(AEP, UK, EE)
1-249-393-11 CARBON
10
5%
1/4W
(AEP, UK, EE)
1-216-295-91 CONDUCTOR, CHIP (2012) (AEP, UK, EE)
R55
Ref. No.
X21
X41
X41
X42
X42
1-760-549-11 VIBRATOR, CRYSTAL (4.5MHz)
1-577-075-11 OSCILLATOR, CERAMIC (456kHz)
(EXCEPT AEP, UK, EE)
1-760-220-11 FILTER, CERAMIC (AEP, UK, EE)
1-527-981-00 FILTER, CERAMIC (AEP, UK, EE)
1-760-220-11 FILTER, CERAMIC (EXCEPT AEP, UK, EE)
X43
1-527-981-00 FILTER, CERAMIC (EXCEPT AEP, UK, EE)
X43
1-577-075-11 OSCILLATOR, CERAMIC (456kHz) (AEP, UK, EE)
************************************************************
*
1-664-014-11 TRANS BOARD
***********
1-533-399-31 HOLDER, FUSE
< CONNECTOR >
* CN901
* CN902
CN903
1-564-522-11 PLUG, CONNECTOR 7P
1-564-518-11 PLUG, CONNECTOR 3P
1-774-108-11 PIN, CONNECTOR (PC BOARD)
< CONNECTOR >
! CNP901
! CNP901
! CNP901
! CNP901
! CNP901
1-558-943-41
1-575-042-21
1-575-651-21
1-696-845-11
1-751-529-11
CORD, POWER (E, MX, PX)
CORD, POWER (US, CND)
CORD, POWER (AEP, AR, EE)
CORD, POWER (AUS)
CORD, POWER (UK)
< FUSE >
! F901
! F902
! F902
1-532-388-31 FUSE, TIME LAG (2A, 250V) (E, AR, AUS, PX)
1-532-504-31 FUSE, TIME LAG (4A, 250V) (E, AR, MX, PX)
1-533-420-11 FUSE, GLASS CYLINDRICAL (DIA.5) (5A,125V)
(US, CND)
! F903
! F904
1-532-505-31 FUSE, TIME LAG (5A, 250V) (AEP, UK, EE)
1-532-505-31 FUSE, TIME LAG (5A, 250V) (AEP, UK, EE)
– 120 –
TRANS
Ref. No.
Part No.
Description
Remark
< RESISTOR >
! R901
! R902
! R903
1-219-120-11 FUSIBLE
1-219-120-11 FUSIBLE
1-219-119-81 FUSIBLE
0.15
0.15
0.1
! R903
1-219-120-11 FUSIBLE
0.15
! R904
1-219-119-81 FUSIBLE
0.1
! R904
1-219-120-11 FUSIBLE
0.15
1-202-725-00 SOLID
3.3M
R907
5%
5%
5%
1/4W
F
1/4W
F
1/4W
F
(US, CND)
5%
1/4W
F
(EXCEPT US, CND)
5%
1/4W
F
(US, CND)
5%
1/4W
F
(EXCEPT US, CND)
10%
1/2W
(US, CND)
< SWITCH >
! S901
1-762-753-11 SWITCH, VOLTAGE SELECTION
(VOLTAGE SELECTOR) (E, AR, PX)
< TRANSFORMER >
! T901
1-431-045-11 TRANSFORMER, POWER (US, CND)
! T901
1-431-047-11 TRANSFORMER, POWER (AEP, UK, EE)
! T901
1-431-048-11 TRANSFORMER, POWER (E, AR, MX, AUS, PX)
************************************************************
Ref. No.
Part No.
!T901
1-431-047-11 TRANSFORMER, POWER (AEP, EE, UK)
6
58
59
120
***************
HARDWARE LIST
***************
#1
#2
#3
#4
#5
7-685-646-79
7-685-871-01
7-685-872-09
7-685-650-79
7-685-862-09
SCREW +BVTP 3X8 TYPE2 N-S
SCREW +BVTT 3X6 (S)
SCREW +BVTT 3X8 (S)
SCREW +BVTP 3X16 TYPE2 N-S
SCREW +BVTT 2.6X6 (S)
#6
#7
#8
#9
#10
7-685-131-19
7-685-533-19
7-621-775-10
7-685-534-19
7-623-921-01
SCREW +BTP 2.6X4 TYPE2 N-S
SCREW +BTP 2.6X6 TYPE2 N-S
SCREW +B 2.6X4
SCREW +BTP 2.6X8 TYPE2 N-S
RING, RETAINING, CAPSTAN
#11
7-621-775-00 SCREW +B 2.6X3
#12
7-621-255-15 SCREW +P 2X3
************************************************************
1-769-974-11 WIRE (FLAT TYPE) (13 CORE)
(EXCEPT: AEP, EE, UK)
1-773-006-11 WIRE (FLAT TYPE) (15 CORE) (AEP, EE, UK)
1-773-161-11 WIRE (FLAT TYPE) (21 CORE)
1-769-949-11 WIRE (FLAT TYPE) (11 CORE)
1-773-051-11 WIRE (FLAT TYPE) (17 CORE)
156
! 158
! 159
357
! 401
1-777-868-11
1-569-007-11
1-569-008-11
1-452-538-11
8-820-020-01
WIRE (FLAT TYPE) (19 CORE)
ADAPTOR, CONVERSION 2P (PX)
ADAPTOR, CONVERSION 2P (AR)
MAGNET
OPTICAL PICK-UP KSS-213D/Q-NP
402
! CNP901
! CNP901
! CNP901
! CNP901
1-769-069-11
1-558-943-41
1-575-042-21
1-575-651-21
1-696-845-11
WIRE (FLAT TYPE) (16 CORE)
CORD, POWER (E, MX, PX)
CORD, POWER (US, CND)
CORD, POWER (AEP, EE, AR)
CORD, POWER (AUS)
! CNP901 1-751-529-11
HP101 1-500-093-11
HRPE1011-500-094-11
M1
X-3371-223-1
M2
A-2004-410-A
CORD, POWER (UK)
HEAD, MAGNETIC (PLAYBACK) (DECK A)
HEAD, MAGNETIC (REC/PB/ERASE) (DECK B)
MOTOR ASSY, CAPSTAN
MOTOR ASSY, DC (TRIGGER)
M101
M102
M201
! T901
MOTOR ASSY (SPINDLE)
MOTOR ASSY (SLED)
MOTOR ASSY (TABLE)
TRANSFORMER, POWER (US, CND)
X-4917-523-4
X-4917-504-1
A-4660-977-A
1-431-045-11
Remark
! T901
1-431-048-11 TRANSFORMER, POWER (E, AR, MX, AUS, PX)
************************************************************
MISCELLANEOUS
**************
6
Description
– 121 –
ACCESSORIES & PACKING MATERIALS
*******************************
1-475-115-11
1-501-374-11
1-501-659-41
1-501-804-11
3-859-536-11
COMMANDER, REMOTE (US)
ANTENNA, LOOP
ANTENNA (FM) (EXCEPT AEP, EE, UK)
ANTENNA (FM) (AEP, EE, UK)
MANUAL, INSTRUCTION (ENGLISH)
(US, CND, E, AR, MX, AUS, PX)
3-859-536-21 MANUAL, INSTRUCTION (FRENCH) (CND)
3-859-536-31 MANUAL, INSTRUCTION (FRENCH, SPANISH)
(E, AR, MX, PX)
3-859-536-41 MANUAL, INSTRUCTION (CHINESE) (PX)
3-859-537-11 MANUAL, INSTRUCTION (ENGLISH)
(AEP, EE, UK)
3-859-537-21 MANUAL, INSTRUCTION
(FRENCH, SPANISH, PORTUGUESE) (AEP)
3-859-537-31 MANUAL, INSTRUCTION (GERMAN) (AEP)
3-859-537-41 MANUAL, INSTRUCTION
(DUTCH, SWEDISH, ITALIAN) (AEP)
3-859-537-51 MANUAL, INSTRUCTION (DANISH, FINNISH)
(AEP)
3-859-537-61 MANUAL, INSTRUCTION (POLISH, RUSSIAN)
(EE)
8-917-581-90 REMOCON, SONY RM-SD70//M SET
The components identified by
mark ! or dotted line with
mark ! are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque ! sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le neméro spécifié.
HCD-D290/G3300/XB3
Sony Corporation
9-960-846-11
Home A&V Products Company
– 122 –
97A0594-1
Printed in Japan © 1997. 1
Published by Service and Safety
Engineering Dept. (Shibaura)

Similar documents

STR-DA4ES/DA7ES/VA333ES

STR-DA4ES/DA7ES/VA333ES area code, are clearly indicated in the text, for example, “Models of area code AA only”. Fig. 1

More information

NSX-R71

NSX-R71 SCHEMATIC DIAGRAM -1/5 (MAIN-1/2, AMP SECTION) ............................................................................................... 25 SCHEMATIC DIAGRAM -2/5 (MAIN-2/2, TUNER SECTION) .....

More information

STR-DE425

STR-DE425 To Exposed Metal Parts on Set

More information

STR-DE435/DE535/SE491/V424/V525

STR-DE435/DE535/SE491/V424/V525 Set the FUNCTION to AM. Turn off the main power.

More information

PCM-R500

PCM-R500 Schematic Diagram – RF Section – ................................... Printed Wiring Boards – MD Section – ............................. Schematic Diagram – MD Section – ...............................

More information