TECHNICAL MANUAL TUP900 SERIES

Transcription

THERMAL PRINTER
TUP900 SERIES
TECHNICAL MANUAL
[ SECOND EDITION ]
INTRODUCTION
This manual describes the thermal printer TUP900 series.
It is designed for use as a reference for periodic inspections and maintenance procedures to be executed
by service personnel. It is not intended for the general user. Users of this manual should have a basic
knowledge and understanding of the English language.
• This manual is divided into the following sections:
Chapter 1
Chapter 2
Chapter 3
• First edition :
Adjustments
Maintenance and Lubrication
Parts List
Apr. 2003
TUP992 only
Second edition : Sep. 2003
Add TUP942
NOTICE
• All rights reserved. Reproduction of any part of this manual in any form whatsoever,
without STAR’s express permission is forbidden.
• The contents of this manual are subject to change without notice.
• All efforts have been made to ensure the accuracy of the contents of this manual at
the time of going to press. However, should any errors be detected, STAR would
greatly appreciate being informed of them.
• The above notwithstanding, STAR can assume no responsibility for any errors in
this manual.
© Copyright 2003 Star Micronics Co.,Ltd.
1
2
3
CHAPTER 1
ADJUSTMENTS
This printer has undergone various adjustments so that it will attain a given standard of performance.
In this chapter, a brief explanation is given of the methods for making adjustments.
Follow the instructions when performing maintenance inspections or when replacing parts to correct
malfunctions.
1.
Adjustment of the Paper End & Black Mark Sensor ............................. 2
2.
Adjustment of the Paper Near End Sensor ........................................... 3
1
1.
Adjustment of the Paper End & Black Mark Sensor
1. Turn the printer off and unplug the power cord.
2. Remove the screws. Then, remove the board chassis.
Screw
Board chassis
VR1
DIP Switch DSW1
Fig. 1-1 Adjustment Volume
LED1
LED2
Fig. 1-2 Control Panel
–2–
3. Since it is adjusted by rotating the volume VR1, check the position of the volume. Prepare a small slotted
screwdriver.
4. Set the paper not for black mark.
5. Use the tip of a thin object to turn off the DIP switch DSW 1-4.
6. Turn the power on.
7. Rotate the volume VR1 using micro screwdriver, to adjust it to a position whereat both the LED1 (green LED) and
the LED2 (red LED) lamps light.
8. Turn the power OFF.
9. Turn the DIP switch DSW 1-4 to its original setting of ON.
This completes the paper end & black mark sensor adjustment.
2.
Adjustment of the Paper Near End Sensor
1. Turn the printer off and unplug the power cord.
2. Remove the screws. Then, remove the board chassis.
Screw
Board chassis
DIP Switch DSW1
VR6
Fig. 1-3 Adjustment Volume
–3–
LED1
LED2
SW2
Fig. 1-4 Control Panel
3. Since it is adjusted by rotating the volume VR6, check the position of the volume. Prepare a small slotted
screwdriver.
4. Set the roll paper.
5. Use the tip of a thin object to turn off the DIP switch DSW 1-4.
6. Press the SW2 switch on the control panel while turning the power switch ON.
7. Rotate the volume VR6 using micro screwdriver, to adjust it to a position whereat both the LED1(green LED) and
the LED2 (red LED) lamps light.
8. When the position where both LEDs for LED1/LED2 light cannnot be found by adjusting VR6, Adjust VR6 to the
position where the LED2 lights and LED1 extinguishes.
9. Turn the power OFF.
10. Turn the DIP switch DSW1-4 to its original setting of ON.
This completes the paper near end sensor adjustment.
–4–
CHAPTER 2
MAINTENANCE AND LUBRICATION
1.
2.
Maintenance ............................................................................................. 6
1-1.
Cleaning the Thermal Head and Platen ............................................................... 6
1-2.
Handling Paper Jams ............................................................................................ 6
1-3.
How to Release the Cutter Lock .......................................................................... 7
Lubrication ............................................................................................... 8
2-1.
Lubricant ................................................................................................................ 8
2-2.
Lubricating Method ............................................................................................... 8
2-3.
Lubricated Areas ................................................................................................... 8
–5–
2
1.
Maintenance
In order to maintain the optimum performance of this printer and to prevent trouble, maintenance must be carried out
according to the following items.
1-1. Cleaning the Thermal Head and Platen
To ensure long-term and stable printing, periodically clean the thermal head and the platen. It is recommended
that you clean every 500,000 lines.
The thermal head and platen can be cleaned by opening the platen unit with the release lever.
• To clean the thermal head heating elements, wipe with a cotton swab dampened with an alcohol based cleaner
(such as ethanol or methanol). Also, do not apply excessive force when doing so. Wipe the heating elements
gently. After cleaning, check that the alcohol has completely evaporated before closing the platen unit.
• Use a soft, dry cotton swab to clean the platen. Wipe away the dirt while rotating the platen.
Also, complete wipe away all of the paper dust on the rubber platen. If the cleaning is incomplete, there may
be problems in paper feeds.
1-2. Handling Paper Jams
If recording paper should become jammed, open the platen unit and remove the jammed paper.
Never pull on the jammed paper unnecessary while the printer unit is closed because this can damage the drive
system parts.
Fig. 2-1 shows the locations to operate (levers/knob) when paper becomes jammed. Remove jammed paper
according to the following procedures.
<TUP992 >
Procedure 1.
2.
3.
4.
Remove the right and left lock levers.
Open the platen unit (including the presenter unit) using the release lever.
Rotate the knob to remove the jammed paper.
Close the platen unit (including the presenter unit) and lock the left and right lock levers.
<TUP942 >
Procedure 1. Open the platen unit using the release lever.
2. Rotate the knob to remove the jammed paper.
3. Close the platen unit. Check that it has been completely closed at this time.
Notes 1) When removing the jammed paper, never move you hands near the tear bar or the auto-cutter because it is very
dangerous. Also, when opening or closing the rotating portions, be careful not to get your hands or fingers
caught.
2) When locking the cutter blades, do not forcefully rotate the platen unit (or the presenter unit) because this can
be the cause of machine failure.
See the following pages for releasing the cutter lock and opening the platen unit.
3) Fig. 2-1 is a conceptual view of a model equipped with a presenter. On models not equipped with a presenter,
operate only the release lever to open the platen unit.
–6–
1-3. How to Release the Cutter Lock
Use the following procedures to release the auto-cutter lock if trouble occurs, such as when paper becomes chewed.
Procedure 1. Turn the apparatus power off.
2. Rotate the emergency knobs in the direction of the arrows on the top of the auto-cutter unit case to return
the cutter blades to their home position.
The emergency knob should be rotated using a tweezers, screwdriver or ball-point pen to prevent
accidents.
Lock lever
Knob
Release lever
Fig. 2-1 Handling Paper Jams
–7–
2.
Lubrication
Lubrication is very important to maintain optimum performance and to prevent trouble.
2-1. Lubricant
The type of lubricant greatly affects the performance and durability of the printer, especially in a low temperature
environment. We recommend use of the grease listed below for this printer.
Type of oil
Grease
Product name
Molykote EM-30L
Maker
Dow Corning Corporation
2-2. Lubricating Method
When lubrication is carried out in assembly and disassembly, wash parts well to remove dust and dirt before lubrication.
Lubrication must be carried out regularly once every 6 months or after 1 million lines have been printed. Lubrication is
necessary irrespective of the regular lubrication whenever lubricant becomes deficient after cleaning or whenever parts
have been disassembled or replaced.
2-3. Lubricated Areas
NO.
Lubricating Point
Grease/Oil
1
Rubbing surfaces of Lock shaft and Platen holder
EM-30L
2
Rubbing surfaces of Lock shaft and Base Frame Unit
EM-30L
3
Rubbing surfaces of Platen Pivot and Base Frame Unit
EM-30L
4
Rubbing surfaces of Gear and Gear
EM-30L
5
Rubbing surfaces of Gear and Shaft
EM-30L
6
Rubbing surfaces of Shaft and Holder roller
EM-30L
7
Rubbing surfaces of PF roller bearing and Shaft
EM-30L
8
Rubbing surfaces of Rear guide and Paper holder
EM-30L
–8–
B
4
1
2
C
B
C
A
5
5
D
4
2
D
A
3
Fig. 2-2 Lubricated Areas (TMP942)
–9–
B
C
A
C
A
7
B
6
7
8
8
Fig. 2-3 Lubricated Areas (PR921)
– 10 –
CHAPTER 3
PARTS LIST
HOW TO USE PARTS LIST
(1)
(2)
(3)
(4)
(5)
(6)
(7)
DRWG. NO.
This column shows the drawing number of the illustration.
REVISED EDITION MARK
This column shows a revision number.
Part that have been added in the revised edition are indicated with “#”.
Part that have been abolished in the revised edition are indicated with “*”.
#1 : First edition → Second edition
*1 : First edition → Second editon
PARTS NO.
Parts numbers must be notified when ordering replacement parts. Parts described as “NPN” have no parts
number and are not in stock, unavailable.
PARTS NAME
Parts names must be notified when ordering replacement parts.
Q’TY
This column shows the number of the part used as indicated in the figure.
REMARKS
Where differences in specifications exist depending on location/destination.
RANK
Parts marked “S” in the rank column can be ordered. Other parts, as a rule, cannot be supplied even if ordered.
Parts marked “O” are optional parts.
1. Printer Assembly ......................................... 12
7. Sub-board ..................................................... 42
1-1. Disassembly Drawing .............................. 12
1-2. Parts List ................................................... 14
7-1. Circuit Diagram ........................................ 42
7-2. Parts List ................................................... 42
2. Mechanism Base Unit ................................. 15
8. Serial Interface Board (25 pin).................... 43
2-1. Disassembly Drawing .............................. 15
2-2. Parts List ................................................... 17
8-1. Circuit Diagram ........................................ 43
8-2. Parts List ................................................... 44
3. Sub-Assembly .............................................. 18
9. Serial Interface Board (9 pin) ...................... 45
3-1. Frame R Unit ............................................. 18
3-2. Frame L Unit ............................................. 19
3-3. Board Chassis Unit .................................. 20
3-4. Presenter Unit PR921 .............................. 21
3-5. Paper Guide Unit (PR921) ...................... 23
3-6. Guide Frame Unit ..................................... 24
3-7. Mechanism Unit TMP942 ......................... 25
3-8. Head Unit .................................................. 27
3-9. Platen Holder Unit .................................... 28
3-10.Paper Guide Unit (TMP942) ..................... 29
9-1. Circuit Diagram ........................................ 45
9-2. Parts List ................................................... 46
4. Block Diagram ............................................. 30
5. Main Logic Board ........................................ 31
5-1. Circuit Diagram ........................................ 31
5-2. Parts List ................................................... 36
6. Control Panel Board .................................... 41
6-1. Circuit Diagram ........................................ 41
6-2. Parts List ................................................... 41
10. USB Interface Board .................................... 47
10-1. Circuit Diagram ........................................ 47
10-2. Parts List ................................................... 48
11. Control Panel Board .................................... 49
11-1. Circuit Diagram ........................................ 49
11-2. Parts List ................................................... 50
3
1.
Printer Assembly
1-1. Disassembly Drawing
A. TUP992
20
17
21
16
19
7
6
17
18
15
13
11
8
12 15
14
12
10
2
12
A
13
11
14
5
9
B
15
3
A
14
B 12
4
14
1
14
14
23
14
22
– 12 –
14
B. TUP942
20
17
16
19
7
6
17
18
15
13
11
8
12 15
14
10
2
12
13
11
14
5
9
B
15
3
14
B 12
4
14
14
23
14
22
1-2. Parts List
Printer Assembly
DRWG.NO. REV. PARTS NO.
1
2
3
4
5
6
7
8
9
10
11
12
12
13
14
15
16
17
18
19
20
21
22
23
-
80701770
37497000
37490050
NPN
NPN
NPN
37490000
37490060
32045600
NPN
NPN
30510530
04991204
04991204
01923004
01903101
01903101
01903030
01914003
33910660
31380100
33910670
33910680
31382040
30781440
30781450
30781460
30781470
30781480
39607400
39607430
39607421
39607440
39607411
39590020
PARTS
NAME
WIRE 18UL1007BRN145TT
NEAR-END DETECTOR UNIT
TUP9
BOARD CHASSIS U UNIT
TUP9
BOARD CHASSIS UNIT
TUP9
FRAME L UNIT
TUP9
FRAME R UNIT
TUP9
MECHANISM BASE UNIT
TUP9
MECHANISM BASE A UNIT
TUP9
PAPER GUIDE
TUP9
BOTTOM FRAME
TUP9
FRAME STAY
TUP9
SPRING E100-100-0284
FASTENER T18S
FASTENER T18S
DESIGNED SCREW 3-4
SCREW TAT 3-6 CT-FL
SCREW TAT 3-6 CT-FL
SCREW TR 3-4 FL
SCREW TR 4-10 WS/WF
ROLL PAPER HOLDER 1
TUP9
ROLL PAPER SHAFT
TUP9
ROLL PAPER HOLDER 2
TUP9
ROLL PAPER HOLDER 3
TUP9
SHAFT C
TMP7
ADAPTER SET PS60L-24A US
ADAPTER SET PS60L-24A EU
ADAPTER SET PS60L-24A UK
ADAPTER SET PS60L-24A AS
ADAPTER SET PS60L-24A CH
INTERFACE BOARD IFBD-HD04
INTERFACE BOARD IFBD-HN04
INTERFACE BOARD IFBD-HU04
INTERFACE BOARD IFBD-HE04
INTERFACE BOARD IFBD-HC04
RHU-T900
– 14 –
Q'TY
1
1
1
1
1
1
1
1
1
1
1
2
4
3
3
11
9
4
2
2
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
REMARKS
RANK
TUP992
S
O
S
TUP992
TUP942
S
S
S
TUP992
TUP942
TUP992
TUP942
TUP992
OPTION
OPTION
OPTION
OPTION
OPTION
SERIAL IF (25 PIN)
SERIAL IF (9 PIN)
SERIAL IF (USB)
ETHERNET
PARALLEL IF
OPTION
S
S
S
S
S
S
S
S
S
S
S
S
S
O
O
O
O
O
O
O
O
O
O
O
2.
Mehcanism Base Unit
2-1. Disassembly Drawing
A. TUP992
12
6
13
4
12
10
5
12
11
12
9
8
7
11
8
9
2
13
3
12
1
– 15 –
B. TUP942
12
6
13
4
12
10
5
11
12
11
2
– 16 –
2-2. Parts List
Mechanism Base Unit
1
2
3
4
5
6
7
8
9
10
11
12
13
38515000
38448300
37491510
37491500
NPN
33913000
33910480
33400130
31900000
09990762
04991204
04991204
01903101
01903101
01903030
01903030
PARTS
NAME
PR921-24
TMP942-24
STOPPER ASSY
TUP9
DAMPER ROLLER ASSY
TUP9
MECHANISM BASE ASSY
TUP9
HANDLE
TUP9
LOOP GUIDE
PR9
LOCK LEVER
PR9
LEVER SCREW
PR9
FERRITE CORE K5BRC16X16X8-M
FASTENER T18S
FASTENER T18S
SCREW TAT 3-6 CT-FL
SCREW TAT 3-6 CT-FL
SCREW TR 3-4 FL
SCREW TR 3-4 FL
– 17 –
Q'TY
1
1
1
1
1
1
1
2
2
1
3
2
9
6
4
2
REMARKS
TUP992
TUP992
TUP992
TUP992
TUP992
TUP992
TUP942
TUP992
TUP942
TUP992
TUP942
RANK
O
O
S
O
S
S
S
S
S
S
S
S
S
S
S
3.
Sub-Assembly
3-1. Frame R Unit
93
5
7
1
2
6
4
9-1
9-2
9-3
9-4
9-5
9-6
9-7
NPN
33210520
30211050
04991254
04020016
02010401
01914003
PARTS NAME
FRAME R ASSY
BUSHING
PF ROLLER BEARING
CORD CLAMP EDS-1208U
STOP RING SE4.0
HEXAGON NUT NH4-1
SCREW TR 4-10 WS/WF
– 18 –
Q'TY
TUP9
TUP9
TMP6
1
1
1
1
1
2
2
REMARKS
RANK
S
S
S
S
S
S
3-2. Frame L Unit
104
10
12
6
8
3
4
9
2
7
11
5
1
12
10-1
10-2
10-3
10-4
10-5
10-6
10-7
10-8
10-9
10-10
10-11
10-12
NPN
33912000
33210520
31382070
30531180
30211050
NPN
04020016
02010401
01914003
01903060
01903030
PARTS NAME
FRAME L ASSY
CLAMP
BUSHING
SHAFT A
CLAMP SPRING
PF ROLLER BEARING
PAPER SET SEAL
STOP RING SE4.0
HEXAGON NUT NH4-1
SCREW TR 4-10 WS/WF
SCREW TAT 3-8 PT-FL
SCREW TR 3-4 FL
– 19 –
Q'TY
TUP9
TUP9
TUP9
TUP9
TUP9
TMP6
TUP9
1
1
1
3
1
1
1
1
2
2
1
3
REMARKS
RANK
S
S
S
S
S
S
S
S
S
S
3-3. Board chassis Unit
7
117
A
7
4
3
A
5
6
1
8
6
2
11-1
11-2
11-3
11-4
11-5
11-6
11-7
11-8
37497200
37490530
37220200
37220001
30721760
04991254
01903030
00630504
PARTS NAME
CONTROL BOARD UNIT
BOARD CHASSIS L ASSY
SUB-BOARD UNIT
MAIN LOGIC BOARD UNIT
CABLE UNIT 6X220CC
CORD CLAMP EDS-1208U
SCREW TR 3-4 FL
SCREW TR 3-5
– 20 –
Q'TY
TUP9
TUP9
PBD-9
TBD9
TUP9
1
1
1
1
1
2
7
2
REMARKS
RANK
O
S
O
O
S
S
S
S
3-4. Presenter Unit PR921
Disassembly Drawing
19
21
14
20
20
2
B 1
A
C
22
16
C
A
13 19
6
22
21
18
12
7
17
19
4
5
8
B
21
19
13
3
21
22
11
– 21 –
10
Presenter Unit PR921
1-1
1-2
1-3
1-4
1-5
1-6
1-7
1-8
1-9
1-10
1-11
1-12
1-13
1-14
1-16
1-17
1-18
1-19
1-20
1-21
1-22
37517030
37514020
37513070
37513060
37513050
37512030
NPN
NPN
37510030
33990010
33910641
33910470
33215010
NPN
30992030
30721740
04991204
00820304
00926403
01902615
04020010
PARTS NAME
TERMINAL BOARD UNIT
SLIP WHEEL
PAPER GUIDE UNIT
HOLDER ROLLER UNIT
PAPER FEED ROLLER UNIT
PAPER FEED MOTOR UNIT
SIDE FRAME L UNIT
SIDE FRAME R UNIT
GUIDE FRAME UNIT
KNOB
PAPER HOLDER
REAR GUIDE
PF ROLLER BEARING
GEAR COVER
DISCHARGE BRUSH
CABLE UNIT 8X350CC
FASTENER T18S
SCREW TR 2-3
SCREW TAT 2.6-4 CT
SCREW TAT 2.6-6 PT
STOP RING SE2.0
– 22 –
Q'TY
PR9
PR9
PR9
PR9
PR9
PR9
PR9
PR9
PR9
PR9
PR9
PR9
PR1
PR9
PR9
PR9
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
4
2
4
4
REMARKS
RANK
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
3-5. Paper Guide Unit (PR921)
1- 3-
2
1
3
1-3-1
1-3-2
1-3-3
37517200
NPN
30045090
PARTS NAME
PE DETECTOR ASSY
PAPER GUIDE
GUIDE
Q'TY
PR9
PR9
PR9
– 23 –
1
1
3
REMARKS
RANK
S
S
3-6. Guide Frame Unit
1- 9-
3
2
4
1
1-9-1
1-9-2
1-9-3
1-9-4
37517200
NPN
NPN
01902028
PARTS NAME
PE DETECTOR ASSY
DETECTOR HOLDER
GUIDE FRAME
SCREW TAT 2-4
Q'TY
PR9
PR9
PR9
– 24 –
2
1
1
1
REMARKS
RANK
S
S
3-7. Mechanism Unit TMP942
21
2-
6
3
B
15
5
1
19
21
7
C
12
19
10
17
B 22
C
A
8
21
13
2
D
9
16
4
20
18
D
11
14
A
19
– 25 –
Mechanism Unit TMP942
2-1
2-2
2-3
2-4
2-5
2-6
2-7
2-8
2-9
2-10
2-11
2-12
2-13
2-14
2-15
2-16
2-17
2-18
2-19
2-20
2-21
2-22
37489011
37487700
37483110
37483040
37483030
37482110
37482010
NPN
NPN
33490060
33400121
33102300
33102290
NPN
NPN
37487320
30721701
30531160
04020010
00716604
01903030
01903101
PARTS NAME
HEAD UNIT
TERMINAL BOARD ASSY
PLATEN HOLDER UNIT
PAPER GUIDE UNIT
SPRING HOLDER UNIT
CUTTER UNIT
PAPER FEED MOTOR UNIT
GEAR COVER UNIT
BASE FRAME UNIT
HEAD ADJUSTER
RELEASE LEVER
GEAR 36X56X0.5
GEAR 18X0.7-58X0.5
PLATEN PIVOT
PRESS SHAFT
PLATEN SWITCH ASSY
CABLE UNIT 14X380CC
RELEASE SPRING
STOP RING SE2.0
SCREW TR 1.6-6
SCREW TR 3-4 FL
SCREW TAT 3-6 CT-FL
– 26 –
Q'TY
TMP9
TMP9
TMP9
TMP9
TMP9
TMP9
TMP9
TMP9
TMP9
TMP9
TMP9
TMP9
TMP9
TMP9
TMP9
TMP9
TMP9
TMP9
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
6
1
REMARKS
RANK
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
3-8. Head Unit
2- 1-
7
2
1
3
5
4
6
2-1-1
2-1-2
2-1-3
2-1-4
2-1-5
2-1-6
2-1-7
NPN
31210001
30905040
30721720
30721711
04991204
01903030
PARTS NAME
HEAD HOLDER
TMP9
COLLAR
TMP8
THERMAL HEAD KF2004-GD31B
CABLE UNIT B
TMP9
CABLE UNIT A
TMP9
FASTENER T18S
SCREW TR 3-4 FL
– 27 –
Q'TY
1
1
1
1
1
1
2
REMARKS
RANK
S
S
S
S
S
S
3-9. Platen Holder Unit
13
2- 3-
1
12
12
5
2
6
11
9
10
7
8
3
9
11
4
10
2-3-1
2-3-2
2-3-3
2-3-4
2-3-5
2-3-6
2-3-7
2-3-8
2-3-9
2-3-10
2-3-11
2-3-12
2-3-13
NPN
NPN
NPN
NPN
30903070
33103020
30375050
NPN
30211050
04020010
04020016
00926403
01903101
PARTS NAME
BLADE COVER
TMP9
BLADE GUIDE
TMP9
PLATEN HOLDER
TMP9
LOCK SHAFT
TMP9
STATIONARY KNIFE KC-GS120
PLATEN GEAR 22X0.7
TMP9
PLATEN
TMP9
SPRING E030-032-0114
PF ROLLER BEARING
TMP6
STOP RING SE2.0
STOP RING SE4.0
SCREW TAT 2.6-4 CT
SCREW TAT 3-6 CT-FL
– 28 –
Q'TY
1
1
1
1
1
1
1
1
2
2
2
2
2
REMARKS
RANK
S
S
S
S
S
S
S
S
3-10. Paper Guide Unit (TMP942)
2- 42
5
4
3
7
10
8
7
6
9
1
9
2-4-1
2-4-2
2-4-3
2-4-4
2-4-5
2-4-6
2-4-7
2-4-8
2-4-9
2-4-10
37487330
NPN
NPN
33910440
33910430
NPN
NPN
04300782
01902024
01902028
PARTS NAME
PE DETECTOR ASSY
TMP9
UPPER GUIDE
TMP9
PAPER GUIDE BASE
TMP9
SIDE GUIDE L
TMP9
SIDE GUIDE R
TMP9
GUIDE PINION 18X0.5
TMP9
RACK
TMP9
O-RING 7.8X1.9 P8SILICON50
SCREW TAT 2-6
SCREW TAT 2-4
– 29 –
Q'TY
1
1
1
1
1
1
2
1
2
1
REMARKS
RANK
S
S
S
S
S
S
4.
Block Diagram
Host Computer
Interface Board
(Parallel, RS-232C, USB, Ethernet)
Main Logic Board
CN41
Control Panel
Board
(OPA-T900)
CN42
Gate Array
Printer Mechanism
Motor Driver
Sensor Circuit
Flash ROM (Program)
512 K x 16 Bits
Feed Motor
CN23
Cutter Driver
Head Driver
Flash ROM (Fonts)
512 K x 16 Bits
Presenter
Driver
SRAM
256 K x 16 Bits
Cutter
CN21
CN22
CN31
Thermal Head
Presenter
(TUP992 only)
CN33
Paper Near
End Sensor
(NEU-T900)
CN32
Paper Near
End Sensor
Sensor Circuit
CPU (HD6412324)
Sensor
EEPROM
3 Pin Regulator
+3.3 V
DC-DC Converter
+5 V
( Prepared by User)
+24 V
CN11
Sub-board (PBD-9)
Power Unit (Adapter Unit PS60L-24A)
– 30 –
5.
Main Logic Board
5-1. Circuit Diagram
9
8
C
C
DD
C
S 8
DD
DD
C
9
O
BC
CC
DS
SS
8B
6
B
S
C
C
P
6
PIO
PIO
PIO
PIO
PIO
PIO
P I O6
PIO
(OD)
(OD)
(OD)
(OD)
(OD)
(OD)
P I O8
P I O9
PIO
PIO
PIO
PIO
O
O
O
O
O
O
O6
O
8
9
CC
C 8
C 9
C
8
9 C 6
DD
C
D6
8
S
P
P
C
8
P
P
D
D
DO
D
6
99
9
S
DD
S
S
S
C
6
BC
D
D
D
D
D
D
D
D
6
8
DD
DD
P P
8
8
6
6
OC
OCB
OC
OCB
P
P
P 6
P
P6
D
6
8
6
8
6
DS
9
8
6
6
6
8
P
P
P
P
P
P
P 6
P
P6
P66
P
P
P
P
D
D
D
D
P
9
6
D
C
9
P DJ
B DJ
PRS DJ
PRS DJ
PRS DJ
OP DJ
D
6
P
P
9
6
9
PRS
JP
JP
JP
JP
JP
JP
DD
JP
JP
8
DB
6
DB
DB
DB
8
P
P
P
P
6
6
8
9
D8
D9
D
D
6
P
P
P
P
P
D
D
DB
DB
DB 8
DB
8
8
D
D
D
D
6
6
8
8
9
6
D
D
6
6
6
CC
8
8
9
SS
SS
6
6
8
8
8
89
B
99
8
8
P
P
P
P
P
P
P
6
O
Protection timer
D
D
DD
SS
SS
SS
D
O Protection timer
6
6
6
6
66
B
B
B
D B
D B
B
B
B
B
DB 8
DB 9
DB
DB
86
8
88
89
D
D
D
D
B8
B9
B
B
DB
DB
DB
DB
9
9
9
9
D
D
D6
D
CS
CS
CDS
CDS
6
6
PRS
PRS
PRS
P
P
8
9
P
B
DUP
8
C
6
8
9
D
B
B
B
B
6
8
CC
CC
SS
SS
SS
SS
SS
SS
SS
9
B 6
B
B 8
B 9
6
6
8
9
9
DD
6
6
CS
S
9
RD
9
8
6
9
P
6
P
6
P
P
96
9
(OD)
(OD)
(OD)
(OD)
(OD)
(OD)
(OD)
(OD)
69
6
8
8
9
6
C B P
99
9
9
CC
SS
SS
SS
SS C
SS
B
B
B
B
B
B
B 8
B 9
D S
D S
C
C
C 6
C
C
C
C 8
C
B
B
B
B
B
B
B6
B
O
O
O
O
O
O
O
O
Protection timer
P PP
6
8
9
D
D
OD
(OD)
(OD)
(OD)
(OD)
B
DD
9
8
68
6
6
6
6
OD 8
S B
CC
CC
SS
SS
SS
6
BC
DP
Protection timer
OP
BC
BC
6
8
B
B
B
B
B
B
B6
S
S
S
S
S
S
OD
SS
SS
SS
B
B
B
B
8
SC
D
DO
D
DO
8
9
BC
6
D
Protection timer
DP
S
S
(OD) S
S
S
S
S
DD
DD
C
6
66
6
8
9
B
BB
BB
BB
BB
BB
BB 6
S
S
S
S
S
S
CO
BC
6
8
D
D
SC
SD
S
SD
S
DD
DD
DD
SS
SS
8
C
BUSY
D
S B
CS
P
O
O
O
B BC
DB
DB
DB
DB
C
9
S BB
DD
DD
DD
SS
SS
9
DB 6
DB 9
DB
DB
6
DD
BC
(OD)
(OD)
(OD)
BC
BC
6
S B
6
D O
JP
JP
P
9
9
8
6
8
BC
P
D
D
D6
D
8
9
O
B
BC
8
9
C B
B S B
DB
S BB
CS B
DD
OC
OCB
OC
OCB
8 S
D
8
9
D
D
D
D
D
D
D 6
D
6
C
C DB
O8
9
P
O8
O9
O
D
D
D
SDB
O
O
O
8
8
8
8
8
8
6
CS
CS 6
(PD)
(PD)
C
98
9
96
9
8
P6
P6
C
DO
6
6
6
66
D
P6
D
8
8
9
D
DD
B
OC
OCB
P
P
S
B
6
88
C
DS
6
6
6
8
S
CS
D
B
8
6
SPB
(OD)
(OD)
(OD)
(OD)
(OD)
(OD)
(OD)
(OD)
C
C
CO
9
6
CC
8
6
SB
S
S
S
S
DB
B
B
6
BB
BB
CS B P
6
68
D
P
P
P
P
P
P
P
P
D
D
D
D
D
D
D
S
S
S
S
68
69
BB
BB
D
DD
CS
CS
8
9
CS
6
8
P6
P6
CS
8
D
D
CS
69
DD
8
9
6
P
P
CS
CS
6
6
6
B
C
DD
8
D
C
86
CS C
(1/5)
– 31 –
Flash
Flash
EPSON BA-T500 Compatible
Manufacturer: molex
(2/5)
– 32 –
(3/5)
– 33 –
Pitch, Thermistor
(4/5)
– 34 –
(5/5)
– 35 –
5-2. Parts List
Main Logic Board
BC01
BC02A-2B
BC02C-2D
BC03A
BC03B-3D
BC03E
BC03F-3G
BC04
BC11
BC12-13
BC14
BC21A
BC21B
BC22
BC23
BC24
BC25
BC31
BC32
C01
C02
C03-04
C09
C12
C13
C14
C15
C16
C17
C18
C20
C21
C22
C23
C24
C26
C28
C30
C301
C32
C34
C36
C37
C39
C40
C400-404
C405-408
C41-42
C43-44
C45-46
C47
C48-49
CN11
CN21
CN22
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
PARTS NAME
CERA.CAPA.CHIP1608 0.022UF 50V
CERA. CAPA. CHIP 0.1UF 50V
CHEM. CAPA.
47UF 35V
CHEM. CAPA.
47UF 35V
CHEM. CAPA.
47UF 35V
CERA.CAPA.CHIP1608 1000PF 50V
CERA. CAPA. CHIP
1UF 10V
CHEM. CAPA. 1000UF 35V
CERA. CAPA. CHIP
1UF 10V
CHEM. CAPA.
47UF 35V
CERA. CAPA. CHIP 100PF 50V
CERA. CAPA. CHIP 100PF 50V
CONNECTOR 5273-04A
CONNECTOR B15B-PH-K-S
– 36 –
Q'TY
1
2
2
1
3
1
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
5
4
2
2
2
1
2
1
1
1
REMARKS
RANK
Main Logic Board
CN23
CN31
CN32
CN33
CN41
CN42
D11
D21-24
DSW1
DSW2
FB01
FB11A-12A
FB21
FB22
FB23
FB31-34
FB41-42
IC01
IC02
IC03
IC04
IC05
IC11
IC12
IC11-12
IC13
IC14
IC15
IC21
IC22
IC23
IC24
IC31
IC32
JP2A
JP3B
JP4-8
JP9A-9B
L1
LED1
LED2
Q1
R001
R002
R003
R004
R005
R006
R007
R008
R009
R010
R011
R015-16
R017-18
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
PARTS NAME
CONNECTOR B8B-PH-K
CONNECTOR PHEC40R-R111
SCHOTTKY DIODE RB160L-40*
SCHOTTKY DIODE CHIP D1FS4*
DIP SWITCH 210B008MS
CHIP RESISTOR
0 OHM 1/16W
BEADS INDUCTOR RH035047RT-Y7
CHIP BEADS IND. BK1608HS601*
CHIP RESISTOR
0 OHM 1/16W
IC-RESET S-80130AN*
CPU
HD6412324SVF25
GATE ARRAY LC24108B-TSPB
EEPROM AT93C46-10SI25
CMOS
74ALVC1G08*
FLASH MEMORY 28F800BJ-70
FLASH MEMORY 28F800BJ-70
FLASH MEMORY SEAL KEI-801
SRAM
D444012AGY-B55X
IC-REG BP5250-24
IC-REG L88M33T*TL
IC-MOTOR MTD2003F-4072
IC-LIN UPC358G2*T1
IC-LIN UPC393G2*T1
IC-MOTOR TA8428K
IC-MOTOR TA8428K
IC-LIN HA17339F*EL
CHIP RESISTOR
0 OHM 1/16W
CHIP RESISTOR
0 OHM 1/16W
CHIP RESISTOR
0 OHM 1/16W
CHIP RESISTOR
0 OHM 1/10W
INDUCTOR CDH74-220L*
LED CHIP LT1E40A*
LED CHIP LT1D40A*
FET CHIP CPH6306*TL
CHIP RES1608 1.5 KOHM 1/16W 5%
CHIP RESISTOR 10 K-OHM 1/16W
CHIP RESISTOR 2.2 K-OHM 1/16W
CHIP RESISTOR 470 OHM 1/16W
CHIP RES1608 220 OHM 1/16W 5%
– 37 –
Q'TY
1
1
1
1
1
1
1
4
1
1
1
2
1
1
1
4
2
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
5
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
REMARKS
TB9 *.*
T9#CH*.*
RANK
Main Logic Board
R019
R020-23
R024
R026-27
R028-30
R035-40
R041
R042-43
R044
R045-46
R047-51
R053
R057
R062-64
R065-66
R067
R068-71
R101
R102
R103
R104
R105
R106
R107
R108
R109
R201-203
R204
R205-207
R208
R209
R210
R211-212
R213-216
R217
R218-220
R221
R222
R223
R251-256
R257
R258-259
R260
R261
R262
R271
R272
R273
R274
R275
R276
R277
R280
R281
R282
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
PARTS NAME
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
CHIP
RESISTOR 100 OHM 1/16W
RESISTOR 10 K-OHM 1/16W
RESISTOR
0 OHM 1/16W
RES1608 220 OHM 1/16W 5%
RES1608 220 OHM 1/16W 5%
RESISTOR 2.2 K-OHM 1/16W
RES3216 0.1 OHM 1/4W
5%
RES1608 30 KOHM 1/16W 1%
RESISTOR
0 OHM 1/16W
RESISTOR 1.0 OHM 1W
RES1608 1 KOHM 1/16W
1%
RES1608 100 KOHM 1/16W 1%
RES1608 5.1 KOHM 1/16W 1%
– 38 –
Q'TY
1
4
1
2
3
6
1
2
1
2
5
1
1
3
2
1
4
1
1
1
1
1
1
1
1
1
3
1
3
1
1
1
2
4
1
3
1
1
1
6
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
REMARKS
RANK
Main Logic Board
R283
R284
R285-286
R291-292
R293-294
R296-297
R301
R302-303
R304-305
R306
R307
R309
R310-311
R312
R313
R315
R316-317
R318
R319
R321
R322
R323
R324
R325
R326
R327
R329
R330-331
R332-335
R336-337
R338-339
R401-403
R404
R405
R407-408
R411-412
R413-414
R415-418
R419-422
R423-424
R433
RA01-04
RA05-09
RA10-12
RA13
RA14-15
RA16-20
SW1-2
TR01
TR02
TR11
TR12
TR13
TR14
TR21
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
PARTS NAME
CHIP RES1608 68 KOHM 1/16W 5%
CHIP RESISTOR
0 OHM 1/10W
CHIP RES1608 220 OHM 1/16W 5%
RESIS. ARRAY CHIP MNR14J221*
PUSH SWITCH SKHHAL
CHIP TRANSISTOR 2SA1362GR*85L
CHIP TRANSISTOR 2SC3875S-G*AL
DIGITAL TRANSISTOR FN1A4P
CHIP TRANSISTOR 2SA1362GR*85L
DIGITAL TRANSISTOR FA1A4P
CHIP TRANSISTOR 2SA1649Z*E1
– 39 –
Q'TY
1
1
2
2
2
2
1
2
2
1
1
1
2
1
1
1
2
1
1
1
1
1
1
1
1
1
1
2
4
2
2
3
1
1
2
2
2
4
4
2
1
4
5
3
1
2
5
2
1
1
1
1
1
1
1
REMARKS
RANK
Main Logic Board
TR22
TR23
VR1-2
VR4-6
XTAL
ZD1
ZD2
ZD3
ZD4
ZD5
-
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
PARTS NAME
CHIP TRANSISTOR 2SA1338-67*TA
RP CHIP RESISTOR EVM3S-47K
RP CHIP RESISTOR EVM3S-47K
CERA. OSC CSACW25M0X51*
ZENER DIODE CHIP HZU20B2TRF
ZENER DIODE CHIP RD3.9SB1*
S/N SEAL KEI-802
– 40 –
Q'TY
1
1
2
3
1
1
1
1
1
1
1
REMARKS
RANK
6.
Control Panel Board
6-2. Parts List
Control Panel Board
CN1
LED1
LED2
R1-2
SW1-2
-
09100860
08300101
08300069
06753314
09010068
30721760
09991910
PARTS
NAME
CONNECTOR S6B-PH-K-R
LED GL3KG8
LED GL3PR8
PUSH SWITCH SKHHBV
CABLE UNIT 6X220CC
TUP9
S/N SEAL KEI-802
– 41 –
Q'TY
1
1
1
2
2
1
1
REMARKS
RANK
7.
Sub-board
7-2. Parts List
Sub-board
C1
CN1
CN2
F1
JP1-3
SW1
-
PARTS NAME
Q'TY
REMARKS
NOT MOUNTED
NPN
NPN
NPN
NPN
NPN
NPN
NPN
CONNECTOR TCS7960-53-2010
CABLE UNIT 4X60CC
PBD-9
FUSE MRT3.15A-250V*
JUMPER WIRE STP122
SEESAW SWITCH SF-W1P1A03BB
– 42 –
1
1
1
1
3
1
1
RANK
8.
Serial Interface Board (25pin)
– 43 –
8-2. Parts List
C1
C2
C3-6
C7-8
C9
CN1
CN2
D1-2
D3
D4-5
DSW1
IC1
IC2
L1-7
L8
L9
R1-2
R3-4
R5-6
R7
R8
R9
R10
R11-12
R13
R14-15
R16
R17
R18
R19-20
R21
R22
R23
R24
RA1
TR1
TR2
TR3
TR4
TR5
TR6
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
PARTS NAME
Q'TY
CHEM. CAPA.
1UF 50V
CHEM. CAPA.
1UF 50V
CONNECTOR PHEC40P-R111
CONNECTOR DBLD-J25SAF-21L9-1
DIODE CHIP MC2840
DIODE CHIP MC2836
1
1
4
2
1
1
1
2
1
IC-I/F ST232CWR*
IC-LIN UPC393G2*T1
CHIP RESISTOR
0 OHM 1/16W
1
1
1
7
1
RESIS. ARRAY 10 K-OHM 1/8W 8EL
CHIP TRANSISTOR 2SA1179M6-STR
2
2
2
1
1
1
1
2
1
2
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
REMARKS
RANK
NOT MOUNTED
NPN
08200201
NPN
NPN
NPN
S
NOT MOUNTED
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
– 44 –
9.
– 45 –
9-2. Parts List
C1
C2
C3-6
C26-35
R1-2
R4-5
R6-7
R8
R11-13
RA1
IC1
IC2-3
IC4
L1-7
L8-9
DSW1
CN1
CN2
CN3
PARTS NAME
Q'TY
NPN
NPN
NPN
CHEM. CAPA.
1UF 50V
1
1
4
NPN
NPN
2
2
CHIP RESISTOR
0 OHM 1/16W
RESIS. ARRAY 10 K-OHM 1/8W 8EL
IC-I/F SP208ECA/TR*
1
3
1
1
REMARKS
RANK
NOT MOUNTED
NOT MOUNTED
NPN
NPN
NPN
08200203
S
NOT MOUNTED
NPN
NPN
CMOS
TC7WU04FU*12L
1
7
NPN
NPN
NPN
CONNECTOR 17LE-23090-27D41
1
1
1
NOT MOUNTED
NOT MOUNTED
– 46 –
10. USB Interface Board
– 47 –
10-2. Parts List
USB Interface Board
BC1
BC2A-2C
BC3
BC4-5
C01
C02
C03
C04
C05
C06
C07
C08
C09-10
C11
CN1
CN2
IC1
IC2
IC3
IC4
IC5
IC6
L1-10
RA01-02
RA03-04
RA05
R01
R02-09
R10-11
R12
R13
R14
R15-16
R17
R18-19
R20
R21
R22-26
R27
TR1
TR2
ZD1
XTAL
PARTS NAME
Q'TY
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
CHEM. CAPA. CHIP 4.7UF 35V
TANTALUM CAPA. CHIP 2.2UF 16V
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
CERA. CAPA. CHIP
51PF 50V
CONNECTOR V23590-T3111
IC-RESET M51953BFP*E2
CPU
M37641M8-128FP
IC SOCKET IC160-0324-300
OTPROM A276308AL-70
CMOS
74LV02AFP*EL
CMOS
74LV573AFP*EL
CMOS
74LV1G04ACME*
CHIP RESISTOR
0 OHM 1/10W
NPN
NPN
NPN
1
1
8
NPN
1
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
CHIP RES3216 33 OHM 1/8W
1%
ZENER DIODE CHIP NNCD5.6LG*T1
CERA. OSC CHIP EFJC2405E5B*
1
2
1
2
1
1
5
1
1
1
1
1
REMARKS
1
3
1
2
1
1
1
1
1
1
1
1
NOT MOUNTED
1
1
1
1
1
1
1
1
1
1
10
2
NOT MOUNTED
NOT MOUNTED
NOT MOUNTED
– 48 –
RANK
11. Parallel Interface Board
– 49 –
11-2. Parts List
Parallel Interface Board
BC1-3
C1
C2
C3-4
C5
CN1
CN2
IC1
IC2
IC3
L1-2
L3-6
L7
L8-10
R1
R2-9
R10
R11
R12
R13
R14
R15
R16
R17
R18
R19-20
R21
R22
R23
R24
R25
RA1
RA2
TR1
PARTS NAME
Q'TY
NPN
3
NPN
1
NPN
NPN
NPN
08211042
NPN
08210126
NPN
09990754
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
CHEM. CAPA.
1UF 50V
CONNECTOR CA-M57R41-2754C
TTL IC 74LS374NSR*EL
TTL IC 74ALS32FP*EL
TTL IC 74LS05FP*EL
CHIP RESISTOR
0 OHM 1/16W
CHIP RESISTOR
0 OHM 1/16W
1
1
1
1
1
1
2
4
1
3
1
8
1
1
1
1
1
1
1
RESIS. ARRAY 4.7K-OHM 1/8W 8EL
RESIS. ARRAY 1.8K-OHM 1/8W 5EL
1
2
1
1
1
1
1
1
1
1
REMARKS
RANK
NOT MOUNTED
NOT MOUNTED
S
S
S
NOT MOUNTED
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
NPN
– 50 –
ELECTRONIC PRODUCTS DIVISION
STAR MICRONICS CO., LTD.
536 Shimizunanatsushinya,
Shizuoka, 424-0066 Japan
Tel : 0543-47-0112
Fax: 0543-48-5013
OVERSEAS SUBSIDIARY COMPANIES
STAR MICRONICS AMERICA, INC.
1150 King Georges Post Road, Edison,
NJ 08837-3729 U.S.A.
Tel : 732-623-5555
Fax: 732-623-5590
http://www.starmicronics.com
STAR MICRONICS EUROPE LTD.
Star House, Peregrine Business
Park, Gomm Road, High Wycombe,
Bucks, HP13 7DL, U.K.
Tel : 01494-471111
Fax: 01494-473333
http://www.StarMicronicsEurope
Please access the following URL
http://www.star-micronics.co.jp/service/frame_sp_spr_e.htm
for the lastest revision of the manual.
Distributed by
2003.09.10
Printed in Japan, 80873386

TECHNICAL MANUAL TUP900 SERIES

Transcription

Similar documents

service manual service-anleitung

service manual - Encompass Parts

DLP Projection TV SERVICE MANUAL

PLASMA TV Parts and Diagrams

Service Manual - Encompass Parts

swiss army knives cutlery timepieces travel gear

Service Manual - LG Parts and Accessories