Bubble Blowing Helicopter Manual

Transcription

Bubble Blowing Helicopter Manual
- Do not use the helicopter in direct sunlight or bright lighting, it will effect the infar-red
signal.
- Do not cover the aerial of the remote control as you will stop the signal to the helicopter.
- Do not stick any lables on to the helicopter, as it could effect the signal to the helicopter
from the remote control.
- This product is made from light weight materials and if not operated correctly, it will
damage the helicopter.
1. Only fly inside in calm air conditions. Away from air conditioners.
2. Fly in a space larger than 20ft(W) x 30ft (L) x 10ft(H)
3. Fly away from electric fans, airconditioners and other dangerous objects.
4. Don not fly near other people.
Please read this manual before
flying and retain for future reference
SPARE PARTS
SPARELIST
PARTS LIST
SPARE PARTS LIST
Order parts from your local retailer or Flying Gadgets - sales@flyinggadgets.com / 0208 952 0471
FG FLIGHT BUBBLE BLOWING HELICOPTER
PARTS EXPLAINED
Balance Bar
Upper Blade
Lower Blade
Rear Blade
Front Canopy
Main Fuselage
Bubble machine
Bubble Container
Landing Skid
Bubble Switch
Charging Socket
Remote Control
Direction Stick
ON/OFF Switch
Performance
Button
1
INFRA-RED Channel
Selector
Power Control
ON/OFF
Switch
Trimmer Switch
BATTERY INSTALLATION & CHARGING
BATTERY
INSTALLATION
Open the battery cover and
insert 6 (AA) batteries. Make
sure they are inserted with the
correct polarity. Then replace
the battery cover.
FORWARDS
To move FORWARDS, push the right
hand direction stick FORWARD and the
helicopter will move FORWARD..
BACKWARDS
To move the helicopter BACKWARDS, move the
left hand direction stick BACKWARDS and the
helicopter will move BACKWARDS.
CHARGING THE
HELICOPTER
BUBBLES
Connect to a
USB port
Remote control charging:
1. Turn the remote control (ON), turn the helicopter power (OFF).
2. Take out the charging wire from the compartment in the remote control.
3. Connect the helicopter up to the remote control.
4. When the LED light on the front of the remote control turns from RED to GREEN charging is completed.
USB Charging:
1. Plug the USB lead in to a computer or USB input.
2. Turn the helicopter (OFF)
3. Connect the lead to the helicopter.
4. When the RED light on the USB switches OFF, charging is completed.
A FULL CHARGE TAKES UP TO 45 MINUTES AND WILL LAST FOR 6 MINUTES.
To turn the bubbles ON, push the left hand
button on the top of the controller and the
helicopter will shoot bubbles out of the back of
the helicopter.
NOTE ON REFUELLING BUBBLES
To fill the bubble tank, use the squeeze bottle
and siringe end. Fill the squeeze bottle up with
bubble fluid then squeeze in to the bubble tank
access hole.
TRIMMING THE HELICOPTER
If the helicopter is moving to the left or the right without any
control inputs. Then you will need to trim the helicopter.
FLYING THE HELICOPTER
- Set the Infra-Red channel selector on the remote control to the same as the helicopter.
- Turn the remote control and then the helicopter (ON)
- Place the helicopter on a flat surface.
- Increase the power on the controller.
- The lights will start flashing on the helicopter and then you can start flying!
FLY UP AND DOWN
To make the helicopter move UP push the left
hand power stick up.
To make the helicopter move DOWN move the
left hand power stick towards you.
Use only small movements for smooth flying.
TURN LEFT/RIGHT
To make the helicopter spin to the LEFT, move
the right hand direction stick to the LEFT.
To make the helicopter spin to the RIGHT, move
the left hand direction stick to the LEFT.
HELICOPTER SPINS TO THE RIGHT
Press the L side of the trim button on the
remote control. Continue pressing until it
stops spinning to the right.
HELICOPTER SPINS TO THE LEFT
Press the R side of the trim button on
the remote control. Continue pressing
until it stops spinning to the left.
BATTERY INSTALLATION & CHARGING
BATTERY
INSTALLATION
Open the battery cover and
insert 6 (AA) batteries. Make
sure they are inserted with the
correct polarity. Then replace
the battery cover.
FORWARDS
To move FORWARDS, push the right
hand direction stick FORWARD and the
helicopter will move FORWARD..
BACKWARDS
To move the helicopter BACKWARDS, move the
left hand direction stick BACKWARDS and the
helicopter will move BACKWARDS.
CHARGING THE
HELICOPTER
BUBBLES
Connect to a
USB port
Remote control charging:
1. Turn the remote control (ON), turn the helicopter power (OFF).
2. Take out the charging wire from the compartment in the remote control.
3. Connect the helicopter up to the remote control.
4. When the LED light on the front of the remote control turns from RED to GREEN charging is completed.
USB Charging:
1. Plug the USB lead in to a computer or USB input.
2. Turn the helicopter (OFF)
3. Connect the lead to the helicopter.
4. When the RED light on the USB switches OFF, charging is completed.
A FULL CHARGE TAKES UP TO 45 MINUTES AND WILL LAST FOR 6 MINUTES.
To turn the bubbles ON, push the left hand
button on the top of the controller and the
helicopter will shoot bubbles out of the back of
the helicopter.
NOTE ON REFUELING BUBBLES
To fill the bubble tank, use the squeeze bottle
and siringe end. Fill the squeeze bottle up with
bubble fluid then squeeze in to the bubble tank
access hole.
TRIMMING THE HELICOPTER
If the helicopter is moving to the left or the right without any
control inputs. Then you will need to trim the helicopter.
FLYING THE HELICOPTER
- Set the Infra-Red channel selector on the remote control to the same as the helicopter.
- Turn the remote control and then the helicopter (ON)
- Place the helicopter on a flat surface.
- Increase the power on the controller.
- The lights will start flashing on the helicopter and then you can start flying!
FLY UP AND DOWN
To make the helicopter move UP push the left
hand power stick up.
To make the helicopter move DOWN move the
left hand power stick towards you.
Use only small movements for smooth flying.
TURN LEFT/RIGHT
To make the helicopter spin to the LEFT, move
the right hand direction stick to the LEFT.
To make the helicopter spin to the RIGHT, move
the left hand direction stick to the LEFT.
HELICOPTER SPINS TO THE RIGHT
Press the L side of the trim button on the
remote control. Continue pressing until it
stops spinning to the right.
HELICOPTER SPINS TO THE LEFT
Press the R side of the trim button on
the remote control. Continue pressing
until it stops spinning to the left.
- Do not use the helicopter in direct sunlight or bright lighting, it will effect the infar-red
signal.
- Do not cover the aerial of the remote control as you will stop the signal to the helicopter.
- Do not stick any lables on to the helicopter, as it could effect the signal to the helicopter
from the remote control.
- This product is made from light weight materials and if not operated correctly, it will
damage the helicopter.
Please read this manual before
flying and retain for future reference
1. Only fly inside in calm air conditions. Away from air conditioners.
2. Fly in a space larger than 20ft(W) x 30ft (L) x 10ft(H)
3. Fly away from electric fans, airconditioners and other dangerous objects.
4. Don not fly near other people.
SPARE PARTS LIST
Order parts from your local retailer or Flying Gadgets - sales@flyinggadgets.com / 0208 952 0471
FG FLIGHT BUBBLE BLOWING HELICOPTER
PARTS EXPLAINED
Balance Bar
Upper Blade
Lower Blade
Rear Blade
Front Canopy
Main Fuselage
Bubble machine
Bubble Container
Landing Skid
Bubble Switch
Charging Socket
Remote Control
Direction Stick
ON/OFF Switch
Performance
Button
1
INFRA-RED Channel
Selector
Power Control
ON/OFF
Switch
Trimmer Switch