SAWMILL LIQUIDATION SMALL LOG MILL LARGE LOG MILL

SAWMILL LIQUIDATION SMALL LOG MILL LARGE LOG MILL

NACHES, WA. 98937
SAWMILL LIQUIDATION
on
SMALL LOG MILL
LARGE LOG MILL
PLANER AND PACKAGING
ROLLING STOCK AND FILING ROOM
SMALL LOG MILL
EQUIPMENT
#1 LOG DECK INFEED:
ONE INFEED LOG DECK – 35 FT. LONG X 30
IN. WIDE – 6 RUNS OF #124 CHAIN – 6 PIN
STOPS – “S” DRIVE – INCLUDES HITACHI 20
HP. – 60 R.P.M. GEAR REDUCER – 2 STOP
AND LOADS – SUB-STEEL TO GROUND.
SOLD
#2 LOG CONVEYOR:
ONE LOG TROTH CONVEYOR – 45 FT. LONG #112 MILL CHAIN – “S” DRIVE WITH 10 HP. –
45 R.P.M. SKK GEAR REDUCER.
#3 LOG CUT OFF SAW:
SOLD
ONE 72 IN. DIAMETER LOG CUT OFF SAW –
SWING TYPE – INSERT TOOTH – 100 HP.
BELT DRIVEN ARBOR – TWO AIR LOG HOLD
DOWNS – 30 HP. HYDRAULIC POWER UNIT –
INCLUDES SAW SHARPENER AND ONE
SPARE SAW BLADE.
SOLD
#4 LOG STOPS WITH LOG CONVEYOR &
KICKER:
LOG STOPS: 8 FT. – 10 FT. – 12 FT. – 14 FT. 16 FT.-18 FT. – 20 FT. – AIR ACTUATED WITH
VALVES – 30 FT. LOG HAUL CONVEYOR
WITH #112 MILL CHAIN – “S” DRIVE – 10 HP.
– 45 R.P.M. SKK GEAR REDUCER – LEFT
HAND LOG DISCHARGE VIA PUNCH AND
DIE KICKERS – AIR ACTUATED.
#5 LOG HAUL CONVEYOR:
ONE 30 FT. LONG LOG HAUL CONVEYOR TO
DEBARKER INFEED – WITH #112 MILL
CHAIN – “S” DRIVE – WITH 10 HP. – 40 R.P.M.
SKK GEAR REDUCER. (RIGHT HAND
SOLD
SOLD
CONVEYOR)
#6 NICHOLSON 27 DEBARKER A-1:
ONE NICHOLSON 27 IN. MODEL A-1 RING
DEBARKER - SER. #215-30056 (MFG 1981)
SIX (6) TOOL ARM MACHINE – AIR HOLD
DOWNS – HYDRAULIC RING CENTERING –
AUTOMATIC HOLD DOWNS AND RING
CENTERING – 75 HP. TWO SPEED RING
DRIVE - 25 HP. TWO SPEED FEEDWORKS
DRIVE – FALK GEAR REDUCER – 20 HP.
HYDRAULIC POWER UNIT – RING LUBE
PUMP – OPERATORS CONTROL CAB AND
CONTROLS. POWERED INFEED HOURGLASS
ROLLS – CENTERING ROLL.
(NOTE: NEW RING BEARING AND AIR SEAL
INSTALLED IN 2004). MACHINE HAS ONLY
BEEN OPERATED ON A SINGLE SHIFT BASIS.
SOLD
#7 LOG HAUL CONVEYOR (barker outfeed):
ONE 30 FT. LONG LOG HAUL CONVEYOR
WITH #112 LADDER CHAIN – “S” DRIVE
WITH RIGHT HAND PUNCH AND DIE KICKER
– SKK 10 P. – 41 R.P.M. GEAR REDUCER.
#8 LOG INFEED TRANSFER TO MAXIMILL:
ONE LOG INFEED TRANSFER DECK, FIVE (5)
RUNS OF #124 MILL CHAIN – 45 FT.
OVERALL LENGTH – “S” DRIVE – FIVE (5)
PIN STOPS AT THE DISCHARGE END – 20 HP.
– 40 R.P.M. HITACHI GEAR REDUCER.
#9 MAXI MILL SYSTEM:
ONE MAXI-MILL SMALL LOG BREAKDOWN
SYSTEM - 8 FT. TO 20 FT. LOG LENGTHS X 22
IN. DIAMETER CAPACITY. COMPLETE
SYSTEM INCLUDES THE FOLLOWING:
INFEED TO CHARGER – X/Y CHARGER,
OVERHEAD END DOGGING CARRIAGE WITH
90 DEGREE INDEX FOR CUTTING 4 SIDED
CANTS – 150 HP. DC CARRIAGE DRIVE AND
SCR CONTROLLER – 85 FT. 120 LB “V” AND
FLAT RAIL – BUMPER STOPS – TWIN 8 KNIFE
TM7E SLABBERS WITH 150 HP. MOTORS –
QUAD SIX 6FT. KLAMATH IRON WORKS
MECHANICAL STRAIN BANDMILLS WITH
150 HP. MOTORS – OUTFEED CANT/BOARD
ROLL CASE AND TRANSFER – FOUR (4) 40
HP. HYDRAULIC PUMPS AND MOTORS
FLOODED SUCTION WITH RESERVOIR AND
HEAT EXCHANGER. OPERATORS
CONTROLS AND MOTOR CONTROL CENTER.
THIS WAS INSTALLED IN THE EARLY 80’S
AND IS IN GOOD TO VERY GOOD
CONDITIONS.
SOLD
SOLD
SOLD
#10 KLAMATH 6 FT. LINE BAR RESAW:
- FIXED LINE BAR –
MOVEABLE SAW “V” AND FLAT WAY
SOLD
DESIGN – MOVEABLE TOP GUIDE – TILT
BACK WHEEL GUARD –– 20 FT. INFEED ROLL
CASE – ROLLS
ARE 10 IN. DIAMETER X 26 IN. WIDE JUMP
CHAINS – CANT TURNER.
(New band wheels in 2005)
#10A - CANT/LUMBER TRANSFER ( TO
RESAW FROM MAXI-MILL):
ONE CANT /LUMBER TRANSFER FROM
MAXI-MILL TO RESAW INFEED ROLLCASE (5) RUNS # 78 MILL CHAIN - 10' OVERALL
LENGTH = “S” DRIVE - WITH 5 HP - 40 RPM
HITACHI GEAR REDUCER.
#10B - RESAW OUT FEED ROLLCASE:
ONE RESAW OUTFEED ROLLCASE 25'
OVERALL LENGTH, ROLLS ARE 8"
DIAMETER X 48" WIDE.
#11 - BOARD TRANSFER TO EDGER:
ONE BOARD TRANSFER TO EDGER - 6 RUNS
OF # 78 MILL CHAIN - 24' LONG X 18' WIDE “S” DRIVE - HITACHI 5 HP - 40 RPM GEAR
REDUCER.
#12 - CANT LANDING TABLE:
ONE CANT LANDING TABLE - 10' OVERALL
LENGTH X 10' WIDE - # 138 CAMEL BACK
CHAIN - WITH 5 HP - 40 RPM HITACHI GEAR
REDUCER.
#13 - LUMBER TRANSFER (TO EDGER):
ONE LUMBER TRANSFER TO EDGER - 8'
LONG X 18' WIDE - 7 RUNS OF # 78 CHAIN “S” DRIVE - 5 HP - 40 RPM HITACHI GEAR
REDUCER.
#14 - SCHURMAN EDGER SYSTEM:
ONE SCHURMAN MODEL 4TA48 BOARD
EDGER - S/N 2257 - TOP KEYED ARBOR - ONE
FIXED SAW - TWO MOVEABLE - AIR
SETWORKS - RIGHT HAND GATE MOVEABLE LASER LIGHTS - 150 HP ARBOR
1,900.00
1,900.00
2,900.00
1,200.00
Missing Photo
1,200.00
16,500.00
DRIVE - TWO SPEED FEEDWORKS - INFEED
TABLE INCLUDES JUMP CHAINS MOVEABLE LINE BAR - BOARD TURNERS OUTFEED TABLE INCLUDES MOVEABLE
POTLATCH EDGING PICKERS.
#15 – LANDING TABLE (Behind Edger):
ONE 8 FT. LONG X 14 FT. WIDE – FIVE (5)
STRAND #138 CAMEL BACK CHAIN WITH 5
HP. – 40 R.P.M. Hitachi gear reducer.
# 16 - LUMBER TRANSFER:
1,200.00
ONE LUMBER TRANSFER, 5 STRAND -35'
LONG X 14' WIDE - # 78 MILL CHAIN - WITH 5
HP - 40 RPM HITACHI GEAR REDUCER.
#17 - LUMBER TRANSFER - (UNDER RESAW
OUTFEED):
1,900.00
ONE LUMBER TRANSFER, 5 STRAND - 12'
LONG X 14' WIDE - # 78 MILL CHAIN - WITH 5
HP - 40 RPM HITACHI GEAR REDUCER.
# 18 - LUMBER TRANSFER:
ONE LUMBER TRANSFER, 5 STRAND - 12'
LONG X 14 WIDE - # 78 MILL CHAIN WITH
AIR ACTUATED PIN STOPS - 5 HP - 40 RPM
HITACHI GEAR REDUCER.
1,200.00
1,200.00
#19 - LUMBER TRANSFER:
ONE LUMBER TRANSFER, 5 STRAND - 12'
LONG X 14' WIDE - # 78 MILL CHAIN WITH
TIPPLE GATE - AIR ACTUATED - 5 HP - 40
RPM HITACHI GEAR REDUCER.
#20 - IRVINGTON MOORE TRIMMER
SYSTEM:
ONE IRVINGTON MOORE LEFT HAND - 4"
TRIMMER SYSTEM - TRIM 20' PASS 26' - 40 HP
LINE SHAFT DRIVE - S/N 19159-L - AIR
OPERATED DROP SAWS - WITH GATHERING
CHAINS - LUG FEEDER - AIR LEAF FENCE. 10
HP SCR FEEDWORKS DRIVE.
SOLD
SOLD
#21 - LUMBER ROLLCASE (BEHIND
TRIMMER TO SORTER):
ONE ROLLCASE TRANSFERRING LUMBER
FROM THE TRIMMER TO THE LSI SORTER
- POWERED ROLLS ARE 8" DIAMETER X 36"
WIDE, 50' OVERALL LENGTH WITH 10 HP 180 RPM HITACHI GEAR REDUCER.
1,700.00
#22 - ROLLCASE BEHIND RESAW:
ONE 38' POWERED ROLLCASE, 8" DIAMETER
X 46" WIDE ROLLS - WITH 10 HP - 155 RPM
HITACHI GEAR REDUCER.
#23 - OVER HEAD LANDING TABLE:
1,900.00
ONE LANDING TABLE – (6) RUNS #138 CHAIN
– 8 FT. LONG X 14 FT. WIDE WITH 5 HP. – 40
R.P.M. GEAR REDUCER.
# 24 - FLOOR CHAINS (PIT):
900.00
ONE FLOOR CHAINS - 12 RUNS OF # 78 MILL
CHAIN WITH LUGS - 28' LONG X 25' WIDE WITH 10 HP - 30 RPM HITACHI GEAR
REDUCER.
# 25 - BELT CONVEYOR (FROM SWAMP
LINE TO RESAW LANDING TABLE):
ONE PAN TYPE BELT CONVEYOR - 100'
LONG X 18" WIDE X 12" DEEP - WITH
RETURN PAN - 15 HP - 155 RPM HITACHI
GEAR REDUCER.
1,900.00
SOLD
#26 - LANDING TABLE & TRANSFER TO
RESAW:
ONE COMBINATION LANDING TABLE AND
TRANSFER, LANDING TABLE HAS 5 RUNS OF
# 138 CAMEL BACK CHAIN AND 5 RUNS OF #
78 MILL CHAIN - 17' OVERALL LENGTH.
WITH 5 HP - 40 RPM HITACHI GEAR
REDUCER.
#27 - BARKER AND HOG MCC:
SELL WITH BARKER
1,900.00
SOLD
#28 - MAXI MILL MCC:
SELL WITH MAXI-MILL
SOLD
#28A - MAXI MILL MCC:
SELL WITH MAXI-MILL
SOLD
#29 - HOG MCC:
SELL WITH HOG
SOLD
#30 - TRIMMER MCC:
SELL WITH TRIMMER
SOLD
#31 - LSI SORTER:
ONE LSI RIGHT HAND 19 BIN - “J” BAR
SORTER - 20' LONG MATERIAL WITH 25 HP
HYDRAULIC POWER UNIT - 4 RUNS TAKE
AWAY CHAINS. 1981 MODEL INCLUDES ALL
DRIVES AND GEAR REDUCERS - BUILDING
ROOF AND TRUSSES.
SOLD
#32 - LUNDEEN 20' STACKER:
ONE LUNDEEN 20' RIGHT HAND STACKER
SYSTEM - WITH STICK LAYER, INCLUDES
UNSCRAMBLER - TRANSFER CHAINS TO
THE STACKER AS WELL AS PACKAGE
REMOVAL - ALL ELECTRICAL - HYDRAULIC
AND GEAR REDUCERS.
NOTE: NO BUILDING
SOLD
MILL WASTE SYSTEM
#33 - WASTE CONVEYOR UNDER THE
MAX-MILL:
ONE WASTE CONVEYOR - 87' OVERALL
LENGTH - 18" WIDE X 18" DEEP - #112
CHAIN WITH FLIGHTS - 10 HP - 40 RPM
HITACHI GEAR REDUCER.
$ 5,900.00
#34 - WASTE CONVEYOR - SECTION # 2
(MAIN):
ONE WASTE CONVEYOR - 70' OVERALL
LENGTH - 18" WIDE X 18" DEEP - #112
CHAIN WITH FLIGHTS - 10 HP - 40 RPM
HITACHI GEAR REDUCER - NEW CHAIN.
#35 - WASTE CONVEYOR ( UNDER
RESAW):
SOLD
ONE WASTE CONVEYOR - 18' OVERALL
LENGTH - 18" WIDE X 18" DEEP - #112
CHAIN - 5 HP 40 RPM HITACHI GEAR
REDUCER.
#36 - WASTE CONVEYOR (UNDER
EDGER):
1,900.00
ONE WASTE CONVEYOR - 30' OVERALL
LENGTH - 18" WIDE X 18" DEEP - #112
CHAIN - 5 HP 40 RPM HITACHI GEAR
REDUCER.
#36A - WASTE CONVEYOR - (UNDER
EDGER INFEED):
ONE WASTE CONVEYOR - 20' OVERALL
LENGTH - 18" WIDE X 18" DEEP - #112
CHAIN - 5 HP - 40 RPM HITACHI GEAR
REDUCER.
#37 - WASTE CONVEYOR (TRIMMER TO
MAIN WASTE):
SOLD
SOLD
SOLD
2,200.00
ONE WASTE CONVEYOR - 72' OVERALL
LENGTH - 18" WIDE X 18" DEEP - #112
CHAIN - 10 HP - 40 RPM HITACHI GER
REDUCER.
# 38 - WASTE CONVEYOR (TRIMMER TO
MAIN WASTE):
ONE WASTE CONVEYOR - 72' OVERALL
LENGTH - 18" WIDE X 18" DEEP - #112
CHAIN - 10 HP - 40 RPM HITACHI GER
REDUCER.
#39 - VIBRATING CONVEYOR:
ONE GENERAL KINEMATICS 68' LONG
BALANCED VIBRATING WASTE
CONVEYOR, S/N 0-4661-1 / M.O. 9027X2X68 - 1/4" PAN THICKNESS - 5'
FIBERGLASS METAL DETECTOR
SECTION - 24" WIDE X 12" DEEP - WITH 24'
SAWDUST AND CHIP SHAKEOUT
SCREENS - RIGHT HAND DISCHARGE TRANSITION TO A KOCKUMS 58"
CHIPPER SPOUT. 10 HP TEFC DRIVE
MOTOR.
2,200.00
SOLD
# 39A - MDI METAL DETECTOR
/SEARCH COIL:
ONE MDI MODEL CCW -78 METAL
DETECTOR WITH 30" WIDE SEARCH
COIL, S/N 51881.
PRICE $1,900
SOLD
# 40 - 58" KOCKUMS CHIPPER:
ONE KOCKUMS 58"BIG MOUTH CHIPPER MODEL 58 - S/N 059-262 -(8) EIGHT KNIFE HORIZONTAL FEED - TOP DISCHARGE.
(DISK NEEDS REBUILDING) WITH 200 HP 1200 RPM ODP MOTOR. BELT DRIVE.
INCLUDES PIPE TO SURGE BIN.
SOLD
# 41 - CHIP SURGE BIN:
ONE 6 UNIT DOUBLE AUGER
SURGE/METERING BIN - WITH 7 ½ HP - 40
RPM HITACHI GEAR REDUCER.
1,200.00
# 42 - KOCKUMS 7' X 7' CHIP SCREEN:
ONE KOCKUMS MODEL KS-77 CHIP
SCREEN - S/N 018062 - 7' X 7'
SOLD
#43 - OVERS CONVEYOR:
ONE OVERS CONVEYOR – 26 FT.
OVERALL LENGTH – 17 IN. WIDE WITH
#112 CHAIN WITH 5 HP. – 40 R.P.M.
HITACHI GEAR REDUCER.
# 44 - DUST CONVEYOR - (FROM
VIBRATING CONVEYOR TO SURGE
BIN):
SOLD
1,400.00
ONE DUST CONVEYOR - 60' OVERALL
LENGTH - 17" WIDE - #112 CHAIN - WITH 7
½ HP - 40 RPM HITACHI GEAR REDUCER.
# 45 - CHIP CONVEYOR - FROM
VIBRATING CONVEYOR TO SURGE BIN
ONE CHIP CONVEYOR:
45' OVERALL LENGTH - 12" WIDE - #110
CHAIN - WITH5 HP - 40 RPM HITACHI
GEAR REDUCER.
# 46 - CHIP CONVEYOR -(FROM SCREEN
TO TRUCK BIN):
ONE CHIP CONVEYOR, 115' OVERALL
LENGTH - 14" WIDE - #112 CHAIN WITH
FLIGHTS - 15 HP - 40 RPM HITACHI GEAR
REDUCER.
SOLD
#47 - HIGH PRESSURE BLOWER:
ONE SUTOBILT 10 X 24 HIGH PRESSURE
BLOWER - VERTICAL INLET AND
DISCHARGE - WITH 125 HP BELT DRIVE
INCLUDES DONALD SON 2' X 6' HIGH
INLET MUFFLER AND 24 X 9' HIGH
DISCHARGE MUFFLER - MERCOID
PRESSURE SWITCH.
SOLD
#48 - 20 X 20 FEEDER:
ONE RADAR MODEL 20 X 20 ESW - S/N 921
FEED WITH 5 HP MOTOR AND DODGE
SHAFT MOUNT GEAR REDUCER - 8"
INJECTION “T”.
# 49 - 8" BLOW PIPE WITH TWO WAY
DIVERTER:
PRICE $ 1.50 PER LINEAR FOOT
SOLD
500 FT.
SOLD
# 50 – FIRST - 30 UNIT TRUCK BIN:
ONE 30 UNIT PEERLESS TRUCK BIN WITH
MAN LADDERS - CAT WALKS - LEVELING
AUGER - BINDICATOR’S HYDRAULIC
GATES (No Hydraulic Power Unit)
SOLD
# 51 – SECOND - 30 UNIT TRUCK BIN:
ONE 30 UNIT PEERLESS TRUCK BIN WITH
MAN LADDERS - CAT WALKS - LEVELING
AUGERS - BINDICATORS HYDRAULIC
GATES (No Hydraulic Power Unit)
SOLD
#52 - 14 UNIT TRUCK BIN:
ONE 14 UNIT TRUCK BIN WITH 6'
CYCLONE - MAN LADDERS - HYDRAULIC
GATES. (No hydraulic power unit) HAS BEEN
DISASSEMBLED.
SOLD
# 52-A - HYDRAULIC POWER UNIT FOR
TRUCK BINS:
ONE 10 HP HYDRAULIC POWER UNIT FOR
THE TRUCK BINS, WITH RESERVOIR.
SOLD
# 53 - BARK CONVEYOR:
ONE BARK CONVEYOR - 62' OVERALL
LENGTH - #112 CHAIN - 18" WIDE X 18"
DEEP - WITH 5 HP - 40 RPM HITACHI
GEAR REDUCER.
# 54 - DUST CONVEYOR - UNDER CUT
OFF SAW:
ONE DUST CONVEYOR - 34' OVERALL
LENGTH - #112 CHAIN - 18" WIDE X 18"
DEEP - WITH 5 HP - 40 RPM HITACHI
GEAR REDUCER.
# 55 - BARK CONVEYOR :
ONE BARK CONVEYOR - 65' OVER ALL
LENGTH - #112 CHAIN - 18" WIDE X 18"
DEEP - WITH 5 HP - 40 RPM HITACHI
GEAR REDUCER.
#56 - HOG INFEED CONVEYOR:
ONE HOG INFEED CONVEYOR - INCLINE
TYPE - 75' OVERALL LENGTH, #112 CHAIN
- 18" WIDE X 18" DEEP - WITH 10 HP - 40
RPM HITACHI GEAR REDUCER.
# 57 - JEFFERY HAMMER HOG:
ONE JEFFERY MODEL WB-45 HAMMER
HOG - S/N 13441 - WITH 200 HP 1770 RPM
MOTOR - BELT DRIVE - WITH INFEED
CHUTE. GOOD CONDITION
SOLD
1,500.00
1,900.00
2,900.00
SOLD
# 58 - DISCHARGE CONVEYOR:
ONE HOG DISCHARGE CONVEYOR - 110'
OVERALL LENGTH - #112 CHAIN INCLINE TO DEEP PILE HOG FUEL.
SOLD
#59 – BOILER FUEL SILO:
ONE BOILER FUEL SILO – 80 UNITS
9,500.00
FILING ROOM
EQUIPMENT
AND ROLLING STOCK
# 63 - KNIFE SHARPENER:
HANCHET MODEL 54-LG - S/N SHOP 60 $ 600.00
#64 – BANDSAW BENCH WITH STRETCHER
ROLL:
ONE ARMSTRONG #4 BANDSAW STRETCHER
ROLL – SER. #13776 WITH TWO 12 IN. X 48 IN. X
4 IN. THICK ANVILS AND ARMSTRONG #14
HEATED WELDING CLAMP.
3,500.00
# 65 - DUAL SIDE GRINDER:
ONE BELL MODEL W1000 - S/N 81H2 DUAL SIDE
GRINDER.
# 66 - SYSTEMATIC GRINDER:
ONE SYSTEMATIC MANUAL TOPPER FACER
GRINDER WITH STAND.
# 67 - ACME SAW GRINDER:
CIRCLE SAW GUMMER GRINDER - S/N 6297 TALL MODEL
# 68 - CIRCLE SAW STRETCHER ROLL:
ONE ARMSTRONG MODEL 3-10 CIRCLE SAW
STRETCHER ROLL - S/N 13714
# 69 - BANDSAW GUIDE DRESSER:
ONE THOMPSON MODEL B - S/N 542 BANDSAW
GUIDE DRESSER
750.00
SOLD
1,100.00
4,900.00
990.00
# 70 - BANDSAW SHARPENER:
ONE ARMSTRONG # 4 LEFT HAND BANDSAW
GRINDER - S/N 13761 WITH FILING CLAMP AND
SAW STANDS
# 71 - BANDSAW SHARPENER:
ONE ARMSTRONG # 4 RIGHT HAND BANDSAW
GRINDER - S/N 13749 WITH FILING CLAMP AND
SAW STANDS.
# 72 - SCHURMAN GUIDE DRESSER
6,900.00
6,900.00
(Will be included in sale of Board Edger)
# 74 - TM&E BENT KNIFE GRINDER
ONE TM&E BENT KNIFE GRINDER - STACK
GRINDER TYPE MODEL MK-299
450.00
ROLLING STOCK
#75 - PURCHASED IN 2003 - HYSTER MODEL H190 H- S/N FOO7EO15557 - S/O
410649 - 16,676 LBS @ 24" - 1000-20
TIRES PERKINS DIESEL ENGINE53"
LONG FORKS - 148" LOAD HEIGHT FORK POSITIONERS – SIDE SHIFT 7,400 HRS. ENCLOSED CAB WITH
AC/HEATER AUTO SHIFT
#76 - CAT MODEL 966D, S/N 99Y03251 – WITH
MEDFORD LOG FORKS, 26.5X25 TIRES
SOLD
SOLD
# 77 - HYSTER MODEL HI50 – MANUAL
TRANSMISSION - PERKINS DIESEL
ENGINE W/O SIDE SHIFT
SOLD
#78 - HYSTER MODEL H150 - MANUAL
TRANSMISSION - PERKINS DIESEL ENGINE W/O
SID SHIFT.
#79 - CAT MODEL 966C - S/N 76J2671
PARTS MACHINE
# 80 – 81 FORD CAB-OVER LUMBER TRUCKS
(YARD)
PRICE $900 EACH (TWO)
SOLD
SOLD
1,800.00
AIR SYSTEM – MILL PARTS
INVENTORY
# 83 - 150 HP AIR COMPRESSOR:
ONE QUINCY NORTHWEST MODEL 740 -B - S/N
810229 ROTARY SCREW AIR COMPRESSOR - NEW
AIR END IN 2005 - AIR COOLED
# 84 - 50 HP AIR COMPRESSOR:
QUINCY NORTHWEST MODEL Q241-D - S/N 950197
- AIR COOLED SKID MOUNTED WITH STARTER
# 85 - AIR DRYER:
ONE PNEUMATECH MODEL AD-750 REFRIGERANT
TYPE AIR DRYER.
# 86 - AIR RECEIVER TANK:
ONE AIR RECEIVER TANK - 48" DIAMETER X 10'
HIGH (VERTICAL) 125 PSIG - WITH WASHINGTON
STATE INSPECTION.
# 87 - NEW 6' KLAMATH IRON WORKS WHEEL:
SOLD
SOLD
1,900.00
SOLD
10" FACE WITH ARBOR
SOLD
# 88 - MILL MACHINERY PARTS INVENTORY:
BEARINGS ARE SOLD
SPROCKETS ARE SOLD
LARGE LOG MILL
EQUIPMENT
#B-1 - INFEED LOG DECK:
ONE INFEED LOG DECK - 6 RUNS OF #132
CHAIN - 32' LONG X 26' WIDE SPLIT DIVES
- TWO (2) SKK 15 HP GEAR REDUCERS (6) SIX PIN STOPS FOR FEEDING INTO
LOG TROTH CONVEYOR - WITH 20 HP
HYDRAULIC POWER UNIT.
SOLD
#B-2 - DEBARKER INFEED CONVEYOR:
ONE 40' LARGE LOG INFEED CONVEYOR C-131 CHAIN - “S” DRIVE - 15 HP
RADICON GEAR REDUCER.
#B-3 - NICHOLSON 60" RING DEBARKER
SYSTEM:
SOLD
ONE NICHOLSON MODEL A-2 - 60" RING
DEBARKER - S/N 220-50101 WITH LARGE
LOG BY-PASS - 78" DIAMETER - 4 TOOL
ARM MACHINE - 75 HP -1200 R.P.M.
FEEDWORKS DRIVE SKK 35:1 GEAR
REDUCER - RING DRIVE IS A 125 HP. –
1200 R.P.M.
MACHINE WAS REBUILT IN 2003 WITH A
NEW RING BEARING AND AIR SEALS SYSTEM INCLUDES CAB WITH
CONTROLS - 3 SECTION MCC CENTER - 20
HP HYDRAULIC POWER UNIT - RING
LUBE PUMP -AUTO HOLDOWN AND RING
CENTERING.
SOLD
#B-4 - POND SAW:
ONE CHAIN POND SAW - 6' BAR - 10 HP
WITH LOG LIFTER
1,500.00
#B-5 - STRETCHER ROLL/BENCH:
ONE ARMSTRONG #5 BANDSAW
STRETCHER ROLL S/N 5665 WITH TWO
14" WIDE X 48" LONG X 4" THICK ANVILS
AND WELDING CLAMP
# B-6 - BANDSAW SHARPENER:
ONE ARMSTRONG MODEL 6D RIGHT
HAND BANDSAW SHARPENER WITH
FILING CLAMP AND STANDS - S/N 5582
CAST MACHINE.
# B-7 -BANDSAW SHARPENER:
ONE ARMSTRONG MODEL 4 RIGHT HAND
BANDSAW SHARPENER WITH FILING
CLAMP AND STANDS - S/N 5729 - CAST
FRONT MACHINE.
1,600.00
1,000.00
2,900.00
# B-8 - CIRCLE SAW SHARPENER:
ONE ACME CIRCLE SAW SHARPENER
850.00
# B-9 - KNIFE GRINDER:
ONE HANCHET MODEL DN-40 –
S/N 9201-P
# B-10 - BABBITT POT
SOLD
ONE RITE-HEAT 30 QUART BABBITT POT
- 110 VOLT .
# B-11 – CHIPPER:
SOLD
ONE BLACK CLAWSON MODEL 6120 S/N
45968 CHIPPER -60" DISK - SIX KNIFE HORIZONTAL FEED - SLANT DISK TYPE WITH 200 HP TEFC 1200 RPM MOTOR.
BELT DRIVE - WORN DISK
7,500.00
# B-11 A SPARE CHIPPER MOTOR:
2,000.00
RE- BUILT - 200 HP @ 1200 ODP
LAYMAN LUMBER
PLANER MILL AREA
#P-1 PLANER- INFEED – BRIDGE –
PLANER:
ONE STETSON ROSS MODEL 505-E
PLANER INFEED - 7' LONG BRIDGE STETSON ROSS MODEL 6-12-C1 PLANER
WITH PROFILES- S/N 4916 – 15 IN. WIDE 16 KNIFE HEADS - 130 HP TOP HEAD - 65
HP BOTTOM HEAD. INSIDE HEAD IS ____
HP OUTSIDE HEAD IS 65 HP. - PROFILE
TOP HEAD IS 65 HP. PROFILE BOTTOM
HEAD IS _______.
SOLD
#P-2 STETSON ROSS GRINDER:
STETSON ROSS MODEL 372 SIDE HEAD
GRINDER
#P-3 KNIFE GRINDER:
ONE HANCHET MODEL DN-40 - S/N 9149
KNIFE GRINDER
#P-4 – COE HYDRAULIC BREAKDOWN:
ONE USED COE HYDRAULIC 20 FT. X 54
IN. HIGH PACKAGE BREAKDOWN TILT
HOIST SYSTEM <-> FOUR INFEED
CHAINWAYS WITH #78 CHAIN AND 7-1/2
HP. GEARHEAD <-> FOUR ARM COE TILT
HOIST AND 20 HP. HYDRAULIC POWER
UNIT WITH 50 GALLON TANK WITH 30 X
30 IN. HEAT EXCHANGER <-> 57 IN.
ELEVATION TO THE TOP OF INFEED
SOLD
1,250.00
SOLD
CHAINWAYS - FROM LEFT TO RIGHT
CHAINWAYS ARE - 0" - 40" - 51" - 68"
SPACING <-> TILT HOIST FOUR ARMS
ARE ON A 57 IN. CENTER.
#P-5 - LOW PRESSURE BLOWER:
ONE LOW PRESSURE 6' BLOWER - 28"
INLET
3,700.00
#P-6 - PEERLESS TRUCK BIN:
ONE PEERLESS 62 UNIT MONO STYLE
TRUCK BIN - S/N 689089 - WITH 10 HP
HYDRAULIC POWER UNIT - MAN
LADDERS - CATWALKS - LEVELING
AUGER
SOLD
#P-7- PACKAGE MAKER:
ONE MAC-FAB 20' PACKAGE MAKER WITH INFEED TO END SQUEEZE RETRACTABLE GATE - SIGNODE MODEL
M22LP S/N 018 SIDE AND TOP LUMBER
SQUEEZE AND BANDER - WITH BOTTOM
CORNER PROTECTORS.
ALL HYDRAULICS AND PLC INCLUDED
45,000.00
P-8 - KILN CARTS:
APPROXIMATELY 150 - GOOD
CONDITION - 9' “I” BEAM
CONSTRUCTION
PRICE EACH $25.00 - LOTS OF 25
MINIMUM
SOLD 162 CARTS
SOLD 300 FT. OF RAIL
3,750.00