Mini Padder Part Manual

Transcription

OZZIES
MINI
PADDER
PARTS MANUAL
REV. A4
OZZIE’S PIPELINE PADDER
7102 WEST SHERMAN STREET
PHOENIX, ARIZONA, 85043
PHONE:(480) 585-9400
FAX:(480) 585-7977
MINI PADDER PARTS MANUAL – REV. A4
OZZIES
INTRODUCTION
This manual contains a complete list of the parts for the Ozzie’s Mini Series Backfill
Separation (padding) Machine, and instructions on how to order replacement parts.
Work involving earth moving equipment can be dangerous, and can result in injury or death
for the operator or for maintenance and support personnel. Most accidents involving
equipment operation, maintenance, and repair are caused by a failure to adhere to basic
safety principles. All personnel must remain alert to potential hazards at all times and take
appropriate precautionary measures to avoid accidents. Never operate or work on machines
unless you have been properly trained.
Please consult Ozzie’s Pipeline Padder, Inc., should you have any questions about this
Machine.
SPECIAL INSTRUCTIONS FOR VIEWING ON A COMPUTER
To correctly view this document in your pdf viewer like Adobe Reader, follow these steps:
In the View menu, Page Display item, the following options should be selected (check
marked):

Two Page View

Show Cover Page in Two Page View.
This will display the part drawing as the left page, and the corresponding parts table as the
right page.
II
INTRODUCTION
OZZIES
SAFETY INSTRUCTIONS
Read these safety instructions before starting any maintenance or repair
operation. Understand and follow these instructions during all maintenance or
repair operations.
 These instructions are meant to supplement your site specific safety information. You
should understand and follow your site specific safety guidelines and rules at all times, in
addition to these instructions.
 WARNING: Maintenance or repair of this machine can be dangerous unless performed
properly. All persons performing maintenance or repair should be properly trained, should
use the appropriate tools and equipment, and should follow the relevant safety procedures
at all times. Ozzie’s dealers are available to provide training, and to answer any questions.
 Do not attempt to perform any maintenance or repair work unless all equipment is lowered
and the hydraulics inoperable. The engine must be stopped, the disconnect switch turned
off, and the key removed before starting any work (unless otherwise specified).
 Wear a hard hat, protective shoes and protective glasses.
 Limit air pressure to 20 kPa (30 psi) when cleaning with air. Never point an air nozzle
toward anyone.
 Know the rating on cables, chains and slings before using them.
 If machine start up could cause injury, attach a ‘DO NOT OPERATE’ or similar warning
tag to the machine start switch before starting work on the machine. These tags are
available from your Ozzie’s dealer.
 Use steps and grab irons, and face the machine when climbing on or off the machine.
 Store rags that have oil or other flammable material on them in a protective container,
away from open fires, welding, or flame cutting areas.
 Operate the engine only in a well-ventilated area. If it is necessary to operate in a closed
area, vent the exhaust to the outside.
 There are certain hazards which must be recognized as potential causes of personal injury.
Be aware of these hazards listed in the next sections, and follow the recommendations.
General Machine Hazards
 Do not use kinked or frayed cable, as it is weaker and may fail. Wear gloves when handling
cable.
 Chips can fly from a steel object or hammer. Wear protective glasses when hammering on
steel, drifts, punches, or chisels. Never strike a punch, drift, or chisel that has a
mushroomed end.
 Any attachment can fall if a control is moved or a hydraulic line breaks.
 Support equipment when working beneath it. Do not depend on hydraulic cylinders to hold
it up.
Elevator Hazards
 Use caution when working around the elevator. Personal injury can result if the elevator or
conveyor is accidentally turned on while persons are on or close to the elevator.
 Be careful when adjustments are being done while the machine is moving or the engine is
running.
Conveyor Hazards
 Use caution when working around the conveyor. Personal injury can result if the elevator
or conveyor is accidentally turned on while persons are on or close to the conveyor.
SAFETY INSTRUCTIONS
III
OZZIES
 Be careful when adjustments are being done while the machine is moving or the engine is
running.
Engine Hazards
 The fan blades will throw or cut any object or tool that falls or is pushed into them.
Burns
 Lubricants will be hot enough to cause serious burns after machine compartments are up
to normal temperature. Allow the compartments to cool before draining lubricant.
 The hydraulic system will be pressurized by hot air in the top of the tank when the system
is at operating temperature.
 Never remove the hydraulic tank cap when the oil is hot. Remove the hydraulic tank cap
slowly to relieve tank pressure. Allow the tank to cool before draining oil.
Oil, Fuel, and Fluids
 Diesel fuel and all lubricants are flammable.
 Do not weld or flame cut on pipes or tubes that contain oil. Clean them thoroughly with
non-flammable solvent before welding or flame cutting on them.
 Do not smoke when refueling, or when working in areas containing fuels.
 Avoid overfilling fuels; clean up oil spills; and steam clean the machine as required to
reduce the risk of fire or explosion.
 Keep all lubricants stored in properly marked containers, and away from children.
 Never put maintenance fluids in glass bottles or in any glass container.
 Keep a close watch for leaks. If leaking is observed, find and correct the source of the leak,
and clean up the leaked fluid.
 Check the fluid levels more frequently than the recommended periods if leaking is
suspected or observed.
Lines, Tubes, and Hoses
 Loose or damaged lines, tubes, and hoses, which leak, can cause fires.
 Do not bend or strike high pressure lines. Do not install bent or damaged lines, tubes or
hoses.
 Inspect all lines, tubes and hoses carefully. Tighten all connections to the recommended
torque. Make sure that all clamps, guards and heat shields are installed correctly to prevent
vibration, rubbing against other parts, or excessive heat during operation.
 Shields, which protect hot exhaust components from oil or fuel spray, in the event of a
line, tube, or seal failure, must be installed correctly.
Battery
 Charging a battery produces a vapor, hydrogen, which is explosive. Do not smoke when
checking batteries, or working around them. Make certain that the disconnect switch is off
when working around batteries.
 A spark at a connection near a battery can cause an explosion. See the Operating Manual
for special precautions when boost starting.
 Battery electrolyte is an acid. Contact with it will harm skin and eyes.
IV
SAFETY INSTRUCTIONS
OZZIES
THIS PAGE INTENTIONALLY LEFT BLANK
V
OZZIES
TABLE OF CONTENTS
INTRODUCTION ........................................................................................................ II
SPECIAL INSTRUCTIONS FOR VIEWING ON A COMPUTER ..................................................... II
SAFETY INSTRUCTIONS.............................................................................................. III
TABLE OF CONTENTS .................................................................................................. VI
SECTION 0: HOW TO USE THIS MANUAL ....................................................................... 10
SECTION 0.1: ORDERING YOUR PARTS........................................................................... 10
SECTION 0.2: HOW TO FIND PART NUMBERS ................................................................... 11
SECTION 0.3: OZZIE'S PART NUMBERS EXPLAINED ............................................................ 13
SECTION 0.4: TERMS AND ABBREVIATIONS...................................................................... 14
SECTION 0.5: DEFAULT MATERIAL TYPES......................................................................... 14
SECTION 0.6: ADDITIONAL NOTES ............................................................................... 15
SECTION 1: FINAL ASSEMBLY ..................................................................................... 16
SECTION 1.1: QUICK CONNECT HOOK ASSEMBLY — 102-1001 ............................................ 18
SECTION 1.2: RIGHT SLACK ADJUSTER ASSEMBLY — 130-0005 ........................................... 20
SECTION 1.3: CUTTING BLADE ASSEMBLY — 130-0006 ..................................................... 22
SECTION 1.4: LEFT SLACK ADJUSTER ASSEMBLY — 130-0004 ............................................. 24
SECTION 1.5: LOWER ELEVATOR MOTOR COVER ASSEMBLY — 130-0007 ................................ 26
SECTION 1.6: LOWER ELEVATOR MOTOR TOP MOUNT ASSEMBLY — 130-0008 .......................... 28
SECTION 2: FRAME ATTACHMENTS VIEW 1 OF 2 ............................................................. 30
SECTION 2: FRAME ATTACHMENTS VIEW 2 OF 2 ................................................................ 32
SECTION 2.1: BOTTOM SUPPORT SKID ASSEMBLY — 132-0002 ............................................ 34
SECTION 2.2: LEFT ELEVATOR ROCK GUARD ASSEMBLY — 132-0003 ..................................... 36
SECTION 2.3: RIGHT ELEVATOR ROCK GUARD ASSEMBLY — 132-0004 ................................... 38
SECTION 2.3.1: TALL DEFLECTOR MOUNT — 151-0001 .................................................. 40
SECTION 2.3.2: SHORT DEFLECTOR MOUNT — 132-1008................................................ 42
SECTION 2.4: LEFT CONVEYOR SHIFT ASSEMBLY ............................................................... 44
SECTION 2.4.1: LEFT CONVEYOR SHIFT FRAME ASSEMBLY — 132-0005 ............................... 46
SECTION 2.4.2: CONVEYOR PIN HOLDING ASSEMBLY — 132-0012 ..................................... 48
SECTION 2.5: RIGHT CONVEYOR SHIFT ASSEMBLY ............................................................. 50
SECTION 2.5.1: RIGHT CONVEYOR SHIFT FRAME ASSEMBLY — 132-0006 ............................. 52
SECTION 2.6: ISOLATOR BRACKET ASSEMBLY — 132-0007 ................................................. 54
VI
TABLE OF CONTENTS
OZZIES
SECTION 2.7: ELEVATOR SPILL PLATE ASSEMBLY — 132-0008 .............................................56
SECTION 2.8: LEFT LOWER HEAD PULLEY COVER ASSEMBLY — 132-0010 ................................58
SECTION 2.9: RIGHT LOWER HEAD PULLEY COVER ASSEMBLY — 132-0011 ..............................60
SECTION 2.10: ELEVATOR WIPE ASSEMBLY — 130-0001 ....................................................62
SECTION 2.10.1: BUSHING HOUSING ASSEMBLY — 132-1011 ..........................................64
SECTION 2.10.2: ELEVATOR WIPE FRAME ASSEMBLY — 132-1010......................................66
SECTION 2.11: ELEVATOR ROLLER WIPE ASSEMBLY — 130-0002 ..........................................68
SECTION 2.11.1: ELEVATOR ROLLER WIPE FRAME ASSEMBLY — 132-1012 ............................70
SECTION 3: FRAME ASSEMBLY .................................................................................... 72
SECTION 3.1: RIGHT SCOOP ASSEMBLY — 132-1001 ........................................................74
SECTION 3.2: LEFT SCOOP ASSEMBLY — 132-1002 ..........................................................76
SECTION 3.3: HITCH PLATE ASSEMBLY — 132-1003 .........................................................78
SECTION 3.4: UPPER ELEVATOR PULLEY MOTOR MOUNT ASSEMBLY — 132-1004 ........................80
SECTION 3.5: BLADE SUPPORT ASSEMBLY — 132-1005 .....................................................82
SECTION 3.5.1: SUPPORTING ASSEMBLY — 132-1006 ....................................................84
SECTION 3.6: LOWER ELEVATOR MOTOR BOTTOM MOUNT ASSEMBLY — 132-1007 ......................86
SECTION 3.7: VALVE STACK ASSEMBLY — 134-0001 ........................................................88
SECTION 3.7.1: VALVE COVER ASSEMBLY — 134-1001 ...................................................90
SECTION 4: ELEVATOR ASSEMBLY................................................................................ 92
SECTION 4.1: UPPER ELEVATOR MOTOR ASSEMBLY .............................................................94
SECTION 4.2: LOWER ELEVATOR MOTOR ASSEMBLY ............................................................96
SECTION 4.3: ELEVATOR CHAIN & PULLEY ASSEMBLY ..........................................................98
SECTION 4.3.1: ELEVATOR CHAINS WITHOUT FLIGHTS ATTACHED ...................................... 100
SECTION 4.3.2: ELEVATOR SLACK PULLEY ASSEMBLY — 131-1004 ................................... 102
SECTION 4.3.3: UPPER ELEVATOR PULLEY ASSEMBLY— 131-1002 .................................... 104
SECTION 4.3.4: LOWER ELEVATOR HEAD PULLEY ASSEMBLY — 131-1003 ........................... 106
SECTION 4.4: ELEVATOR BELT ADJUSTER ASSEMBLY — 130-0003 ....................................... 108
SECTION 4.4.1: BELT ADJUSTER FRAME — 132-1015 ................................................... 110
SECTION 4.5: ELEVATOR BELT – 131-9027 .................................................................. 112
SECTION 5: VIBRATOR ASSEMBLY ............................................................................. 114
SECTION 5.1: VIBRATOR SHAFT ASSEMBLY .................................................................... 116
SECTION 5.2: VIBRATOR FRAME ASSEMBLY — 132-0009 .................................................. 118
SECTION 5.3: VIBRATOR MOTOR BRACKET ASSEMBLY — 132-1009...................................... 120
SECTION 5.4 WEIGHTED SHAFT ASSEMBLY — 132-2093................................................... 122
SECTION 6: CONVEYOR ASSEMBLY VIEW 1 OF 6 ........................................................... 124
TABLE OF CONTENTS
VII
OZZIES
SECTION 6: CONVEYOR VIEW 2 OF 6 ...........................................................................
SECTION 6.1: CONVEYOR BELT — 151-9005 ...............................................................
SECTION 6.2: CONVEYOR FRONT FRAME ASSEMBLY — 152-1001 ........................................
SECTION 6.3: CONVEYOR BACK FRAME ASSEMBLY — 152-1002 .........................................
SECTION 6.4: FRONT RIGHT DEFLECTOR ASSEMBLY — 152-1004 .......................................
SECTION 6.5: FRONT LEFT DEFLECTOR ASSEMBLY — 152-1005 .........................................
SECTION 6.6: BACK RIGHT DEFLECTOR ASSEMBLY — 152-1003 .........................................
SECTION 6.7: BACK LEFT DEFLECTOR ASSEMBLY — 152-1006 ...........................................
SECTION 6.8: CONVEYOR LEFT MOTOR MOUNT ASSEMBLY — 152-1008 ................................
SECTION 6.9: RIGHT MOTOR MOUNTING ASSEMBLY— 152-1009 ........................................
SECTION 6.10: PULLEY WIPER MOUNT ASSEMBLY — 152-1010 .........................................
SECTION 6.11: HEAD PULLEY ASSEMBLY — 151-0003 ....................................................
SECTION 6.12: CONVEYOR ROLLER ASSEMBLY — 151-0002..............................................
126
128
130
132
134
136
138
140
142
144
146
148
150
152
154
156
158
SECTION 7: ADDITIONAL LOADER, ELECTRICAL AND PADDER PARTS NOT SHOWN IN VIEWS ... 160
INDEX OF PART NUMBERS ........................................................................................ 161
INDEX OF PART NAMES ........................................................................................... 164
VIII
TABLE OF CONTENTS
OZZIES
THIS PAGE INTENTIONALLY LEFT BLANK
TABLE OF CONTENTS
IX
OZZIES
SECTION 0: HOW TO USE THIS MANUAL
This manual shows parts that can be ordered through Ozzie's parts department. Refer to
the ‘Ordering Your Parts’ section below for step by step instructions.
SECTION 0.1: ORDERING YOUR PARTS
Before ordering parts, be sure to read the introductory sections of this parts manual:

Safety Instructions

How To Find Part Numbers

Part Numbers Explained

Terms and Abbreviations

Default Material Types

Additional Notes
In order to order your parts for your machine, you will need the following information:
1.
2.
3.
4.
YOUR COMPANY NAME
JOB LOCATION
ADDRESS WHERE PARTS WILL BE SENT
OZZIE'S MINI PADDER MACHINE SERIAL NUMBER: MP_ _ _
» THIS INFORMATION IN LOCATED ON THE PARTS BOX SUPPLIED WITH THE MACHINE, AND ON THE
SIDE OF THE MACHINE. IT WILL ALWAYS START WITH MP, AND END WITH THREE (3) DIGITS.
5. PART NUMBER(S)
» READ THE SECTION ‘HOW TO FIND PART NUMBERS’ TO GET HELP FINDING PART NUMBERS IN
THIS BOOK
6. OZZIE'S PARTS DEPARTMENT PHONE NUMBER
» THIS CAN BE FOUND ON THE FRONT AND BACK COVERS OF THIS PARTS MANUAL
7. JOB SITE CONTACT PHONE NUMBER
» SUPPLYING OZZIE'S WITH A PHONE NUMBER ALLOWS US TO COMMUNICATE ABOUT
AND TO REACH YOU IN THE CASE OF AN ISSUE.
10
SHIPMENTS,
OZZIES
SECTION 0.2: HOW TO FIND PART NUMBERS
This manual is designed to be displayed over two pages. The illustrations of the assemblies
and sub-assemblies are shown on the left hand (even-numbered) pages. Their component
parts are shown exploded out from the assembly, and are identified with callout numbers.
The parts list tables are shown on the right hand (odd-numbered) pages. The picture below
shows an example of a pair of part manual pages, followed by explanations of each section.
A
C
B
D
E
Section A (Header Block)
The header block is displayed at the top of every page. The outside edge has the document
name and version. The inside edge shows the Ozzie's logo.
Section B (Section Block)
The section block is on every page, below the header block. It has the section number, the
formal title of the assembly, and the assembly part number, where applicable.
It is important to understand that parts belong to sub-assemblies, and that sub-assemblies
belong to assemblies. If an entire assembly (or sub-assembly) is needed, then the assembly
part number should be used for the order. If only one or more of the component parts of a
sub-assembly or assembly are required, then refer to the parts list table for the correct
part number(s).
11
OZZIES
Section C (Illustration)
The illustrations are always displayed on the left hand page. This is a CAD drawing of an
assembly or sub-assembly, with its parts and/or sub-assemblies exploded out, and labeled
with callout numbers.
Use the diagram to find the part you need, and to determine its callout number. Use the
parts list table on the right hand page, and the callout number, to find the part number.
At the beginning of each new section, the main assembly for that section is shown with its
sub-assemblies exploded out. The ‘See Page’ column in the parts list table contains the
page number of the sub-assembly illustration.
The exploded view trail lines show the locations of the assembled parts.
necessarily show how to assemble the parts.
They do not
Section D (Parts List Table)
The parts list table shows the List of parts or assemblies for each exploded piece in the
illustration, along with the quantity, description and page number of additional information
(if applicable). The columns of the parts list table are described below:
Item # – The callout number on the illustration.
Part # – The number of the assembly or part.
Qty. – The total quantity of this piece used in the assembly. All pieces may not be exploded
out in the illustration, but will still be counted. Bolt, nuts, and washers will only be counted
when they are directly being used in the illustration. In the sample on the previous page,
bolt used to attach the hitch plate will be used, but bolts inside the unexploded assembly
will not be shown.
Description – The formal part or assembly description. If it says assembly at the end of
description, then it is an assembly number, and you will need to go to the page listed under
‘See Page’ to get component part numbers for that assembly.
The majority of parts follow the material defaults listed in the table below. If the parts are
not made of the material in the default table, then the material will be shown inside
parenthesis ().
See Page – If the piece exploded in the illustration is an assembly, then the page number
of the illustration for that assembly will be shown here. If the assembly can only be ordered
as a whole assembly (that is, if none of the component parts can be ordered, e.g. the dirt
deflector), then no page number will be shown.
Section E (Footer Block)
Located at the bottom of each page, the footer block has the page number on the outside
edge, and has the name of the main assembly that the illustrated assembly belongs to, on
the inside edge. For example, the cutting blade sub-assembly, part number 130-0006, has
its own two pages, but at the bottom of those pages, the footer reads ‘Final Assembly’,
because the cutting blade is considered part of the final assembly.
12
OZZIES
SECTION 0.3: OZZIE'S PART NUMBERS EXPLAINED
X X X X - X X X X
Serial Number
Part Type
Assembly Category
System
Machine
Machine:
0) Micro Padder
1) Mini Padder
2) OPP-200
3) OPP-300
4) MS-4000
5) MS-2500
6) Large Padders
7) Multiple Machines (Shared Parts)
8) Pumps
9) Shared Sideboom Parts
10) Liebherr 64 Sideboom
14) Liebherr Welding Tractor
15) Rock crushers
Mini Padder Systems:
0) General Assembly
1) Engine, Pumps, Coolers
2) Tracks, Carbody, Sub-Frame
3) Elevator, Scoop, Engine Platform
4) Shaker Assembly
5) Conveyor Assembly
6) Fuel Tank, Hyd. Tank, Air Tank
7) Operator Station
8) Accessories
9) Unassigned
Assembly Category:
0) Final Assembly (Labels, Decals, Specs)
1) Mechanical (Shafts, Sprockets, Idlers)
2) Weldment (Frames, Gussets, Brackets)
3) Transmission (Engine, Final Drive,
Elevator Drive)
4) Hydraulic (Pumps, Motors, Hoses,
Fittings, Valves, Cylinders)
5) Electrical (Lights, Sensors, Screens,
Wirings, Plugs, Controls)
6) Pneumatic (Lines, Fittings, Regulators)
7) Schematics (Hydraulic, Pneumatic,
Electrical)
8) Unassigned
9) Unassigned
Part Type:
0) Assemblies
1) Weldment
2) Built Parts
3) Built Parts
4) Built Parts
5) Built Parts
6) Built Parts
7) Built Parts
8) Built Parts
9) Purchased Parts
13
OZZIES
SECTION 0.4: TERMS AND ABBREVIATIONS
TERM
1020
A36
A500
AISI
ANSI
ASME
ASTM
CS
HSS
NPT
PURCHASED PARTS
T-1
TPI
UNC
UHMW
DEFINITION
1020 refers to AISI Specification, Type 1020 Steel
A standard steel alloy which is a common structural steel used in the
United States.
A500 refers to ASTM HSS A500 Grade B
American Iron and Steel Institute
an association of North American steel producers
American National Standards Institute
An international standards organization
American Society of Mechanical Engineers
A standards organization
American Society for Testing and Materials
An international standards organization
Counter Sunk
Hollow Structural Sections
a type of metal profile with a hollow tubular cross section. In some
countries they are referred to instead as a structural hollow section (SHS)
National pipe thread
a United States standard for tapered threads used to join pipe and fittings
Parts that be bought off the shelf from a vendor by supplying a brand and
part number
T-1 refers to A514 Steel, Type T-1
Threads per inch
a measure used with threaded fasteners
Unified National Coarse, or Unified Coarse Thread
defines a standard thread form for Hex Bolt threads
Ultra-high-molecular-weight polyethylene
an odorless, tasteless, nontoxic, and self-lubricating thermoplastic
polyethylene. Also known as UHMWPE, high-modulus polyethylene,
(HMPE), or high-performance polyethylene (HPPE)
SECTION 0.5: DEFAULT MATERIAL TYPES
Unless otherwise specified in the parts table, the following parts are made to the following
specifications:
PART TYPE
COUNTERSUNK HEX BOLT
FLAT WASHER
HEX BOLT
HEX NUT
HEX BOLT
LOCK WASHER
STEEL PLATE
TUBE
14
MATERIAL DEFAULT
ANSI B18.6.3
ANSI B18.22.1 TYPE B
ANSI/ASME B18.2.1
ANSI B18.2.2 TYPE B
ANSI B18.3
ANSI B18.21.1
A36 STEEL
A500
OZZIES
SECTION 0.6: ADDITIONAL NOTES

All bearings come with grease fittings installed, but additional fittings can be ordered

Some illustrations may be different from your unit.

Some illustrations might show parts covers removed for clarification.

Continuing improvement and advancement of product design may have caused changes
to your machine which may not be covered in this publication.

Each publication is reviewed and revised, as required, to update and include any
changes in later editions.
15
OZZIES
SECTION 1: FINAL ASSEMBLY
16
OZZIES
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
PART #
102-1001
HEX BOLT
WASHER
182-2009
130-0005
HEX BOLT
WASHER
704-9001
131-9016
704-9000
704-9004
130-0007
130-0008
WASHER
HEX BOLT
HEX BOLT
130-0006
130-0004
QTY.
1
32
32
1
1
12
8
4
2
2
2
1
1
2
2
5
1
1
DESCRIPTION
QUICK CONNECT HOOK ASSEMBLY
3/ ” ⌀ X 2” LENGTH – 10 UNC
4
3/ ”, LOCK
4
DIRT DEFLECTOR
RIGHT SLACK ADJUSTER ASSEMBLY
1/ ” ⌀ X 11/ ” LENGTH – 13 UNC
2
2
1/ ” , FLAT, NARROW
2
GREASE FITTING (STRAIGHT, 1/8” , NPT)
BEARING
GREASE FITTING (90°, 1/8” NPT)
GREASE FITTING (STRAIGHT, 1/4” , 28 UNC)
LOWER ELEVATOR MOTOR SHIELD ASSEMBLY
LOWER ELEVATOR MOTOR TOP COVER ASSEMBLY
3/ ” , FLAT, REGULAR
8
3/ ” ⌀ X 1” LENGTH – 16 UNC
8
1/ ” ⌀ X 11/ ” LENGTH – 13 UNC, CS HEX HEAD
2
2
CUTTING BLADE ASSEMBLY
LEFT SLACK ADJUSTER ASSEMBLY
SEE PAGE
18
—
—
—
20
—
—
—
—
—
—
26
28
—
—
—
22
24
17
OZZIES
SECTION 1.1: QUICK CONNECT HOOK ASSEMBLY — 102-1001
2
1
3
18
4
5
6
OZZIES
ITEM #
1
2
3
4
5
6
SECTION 1.1: QUICK CONNECT HOOK ASSEMBLY — 102-1001
PART #
102-2003
102-2002
102-2004
102-2001
102-2006
102-2005
QTY.
4
1
2
2
2
1
DESCRIPTION
HOOK DOUBLER PLATE
BACK PLATE
STOP BLOCK
QUICK CONNECT HOOK
RIB
HITCH BOLT PLATE
SEE PAGE
—
—
—
—
—
—
19
OZZIES
SECTION 1.2: RIGHT SLACK ADJUSTER ASSEMBLY — 130-0005
20
OZZIES
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
SECTION 1.2: RIGHT SLACK ADJUSTER ASSEMBLY — 130-0005
PART #
HEX NUT
HEX NUT
132-2133
132-2129
132-2128
132-2134
132-2132
WASHER
132-2135
132-9005
132-2131
132-2125
132-2124
132-2127
132-2126
132-2130
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
DESCRIPTION
5/ ”
8
⌀– 18 UNC
1” ⌀– 8 UNC
THREADED ROD
GUSSET
MOUNT PLATE
SPACING PLATE
UPPER SPRING SEAT
ASTM F436 1”, CIRCULAR
SLACK ADJUSTER ROD END
SPRING
LOWER SPRING SEAT
GREASE INNER TUBE
GREASE OUTER TUBE
BEARING MOUNT PLATE
ADJUSTER MOUNTING PLATE
BRACKET
SEE PAGE
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
21
OZZIES
SECTION 1.3: CUTTING BLADE ASSEMBLY — 130-0006
1
2
22
OZZIES
ITEM #
1
2
SECTION 1.3: CUTTING BLADE ASSEMBLY — 130-0006
PART #
132-2136
132-2137
QTY.
DESCRIPTION
1 CUTTING EDGE PLATE (AR500)
4 CUTTING EDGE FINS (AR500)
SEE PAGE
—
—
23
OZZIES
SECTION 1.4: LEFT SLACK ADJUSTER ASSEMBLY — 130-0004
24
OZZIES
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
SECTION 1.4: LEFT SLACK ADJUSTER ASSEMBLY — 130-0004
PART #
132-2129
132-2126
132-2130
HEX NUT
HEX NUT
132-2133
132-2128
132-2134
132-2132
WASHER
132-2135
132-9005
132-2131
132-2125
132-2124
132-2127
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
DESCRIPTION
GUSSET
ADJUSTER MOUNTING PLATE
BRACKET
5/ ” ⌀– 18 UNC
8
1” ⌀– 8 UNC
THREADED ROD
MOUNTING PLATE
SPACING PLATE
UPPER SPRING SEAT
ASTM F436 1”, CIRCULAR
SLACK ADJUSTER ROD END
SPRING
LOWER SPRING SEAT
GREASE INNER TUBE
GREASE OUTER TUBE
BEARING MOUNT PLATE
SEE PAGE
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
25
OZZIES
SECTION 1.5: LOWER ELEVATOR MOTOR COVER ASSEMBLY — 130-0007
1
2
3
4
26
OZZIES
ITEM #
1
2
3
4
SECTION 1.5: LOWER ELEVATOR MOTOR COVER ASSEMBLY — 130-0007
PART #
132-2138
132-2141
132-2139
132-2140
QTY.
1
1
1
1
DESCRIPTION
MOTOR COVER MOUNTING PLATE
MOTOR COVER DEFLECTING PLATE
COVER TUBE (A53 GRADE B)
MOTOR COVER END PLATE
SEE PAGE
—
—
—
—
27
OZZIES
SECTION 1.6: LOWER ELEVATOR MOTOR TOP MOUNT ASSEMBLY — 130-0008
3
2
1
28
OZZIES
ITEM #
1
2
3
SECTION 1.6: LOWER ELEVATOR MOTOR TOP MOUNT ASSEMBLY — 130-0008
PART #
132-2041
132-2142
132-2143
QTY.
1 FRONT PLATE
1 COVER PLATE
2 SEAT BLOCK
DESCRIPTION
SEE PAGE
—
—
—
29
OZZIES
SECTION 2: FRAME ATTACHMENTS
3
1
2
6
5
4
7
3
8
10
13
3
9
7
15
16
12
11
14
20
21
15
19
18
16
17
10
3
10
30
3
OZZIES
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
PART #
132-0003
HEX BOLT
WASHER
131-2007
701-9000
132-0004
HEX BOLT
131-2009
132-2147
HEX BOLT
131-2035
131-2034
—
—
HEX BOLT
WASHER
132-0011
HEX BOLT
132-0010
130-0001
130-0002
QTY.
1
12
31
2
2
1
20
2
1
5
2
2
1
1
8
8
1
8
1
1
1
DESCRIPTION
LEFT ELEVATOR ROCK GUARD ASSEMBLY
3/ ” ⌀ X 11/ ” LENGTH – 16 UNC
8
2
8
RETAINER PLATE
ELEVATOR RUBBER FLASHING
RIGHT ELEVATOR ROCK GUARD ASSEMBLY
3/ ” ⌀ X 3/ ” LENGTH – 16 UNC
8
4
DEFLECTOR STOP
VIBRATOR WIPE PLATE
3/ ” ⌀ X 1” LENGTH – 16 UNC
8
RUBBER RETENTION PLATE
VIBRATOR ROLLER RUBBER
LEFT CONVEYOR SHIFT ASSEMBLY
RIGHT CONVEYOR SHIFT ASSEMBLY
1/ ” ⌀ X 13/ ” LENGTH – 13 UNC
2
4
2
RIGHT LOWER HEAD PULLEY COVER ASSEMBLY
1/ ” ⌀ X 11/ ” LENGTH – 13 UNC, CS FLAT HEAD
2
2
LEFT LOWER HEAD PULLEY COVER ASSEMBLY
FRICTION DRIVE WIPE ASSEMBLY
ELEVATOR ROLLER WIPE ASSEMBLY
SEE PAGE
36
—
—
—
—
38
—
—
—
—
—
—
44
50
—
—
60
—
58
62
68
31
OZZIES
SECTION 2: FRAME ATTACHMENTS VIEW 2 OF 2
12
3
11
10
1
1
2
3
4
5
6
9
7
8
32
OZZIES
ITEM #
SECTION 2: FRAME ATTACHMENTS VIEW 2 OF 2
PART #
QTY.
1
HEX BOLT
8
2
3
4
5
6
7
8
9
10
11
12
WASHER
HEX NUT
132-0007
131-2003
HEX BOLT
WASHER
132-0002
132-2146
131-2002
WASHER
132-0008
64
8
24
1
7
7
2
2
1
16
1
1/ ”
2
1/ ”
2
1/ ”
2
⌀
X 11/2”
DESCRIPTION
LENGTH – 13 UNC
, FLAT, REGULAR
⌀ – 13 UNC
ISOLATOR BRACKET ASSEMBLY
RIGHT SIDE PLATE
3/ ” ⌀ X 1” LENGTH – 16 UNC
8
8
BOTTOM SUPPORT SKID ASSEMBLY
SCOOP WEAR PLATE
LEFT SIDE PLATE
2
ELEVATOR SPILL PLATE ASSEMBLY
SEE PAGE
—
—
—
54
—
—
—
34
—
—
—
56
33
OZZIES
SECTION 2.1: BOTTOM SUPPORT SKID ASSEMBLY — 132-0002
3
2
1
34
OZZIES
ITEM #
1
2
3
SECTION 2.1: BOTTOM SUPPORT SKID ASSEMBLY — 132-0002
PART #
132-2049
132-2047
132-2048
QTY.
1 SKID PLATE
1 TOP PLATE
2 RIB PLATE
DESCRIPTION
SEE PAGE
—
—
—
35
OZZIES
SECTION 2.2: LEFT ELEVATOR ROCK GUARD ASSEMBLY — 132-0003
6
5
1
3
2
4
36
OZZIES
ITEM #
1
2
3
4
5
6
SECTION 2.2: LEFT ELEVATOR ROCK GUARD ASSEMBLY — 132-0003
PART #
132-2053
132-2052
132-2054
HEX NUT
132-2051
132-2050
QTY.
1
4
1
6
1
1
DESCRIPTION
END RIB
RIB PLATE
INSIDE FLUSH PLATE
3/ ” ⌀ – 16 UNC
8
OUTSIDE FLUSH PLATE
TOP PLATE
SEE PAGE
—
—
—
—
—
—
37
OZZIES
SECTION 2.3: RIGHT ELEVATOR ROCK GUARD ASSEMBLY — 132-0004
1
2
3
4
5
6
8
7
38
OZZIES
ITEM #
1
2
3
4
5
6
7
8
SECTION 2.3: RIGHT ELEVATOR ROCK GUARD ASSEMBLY — 132-0004
PART #
132-2055
132-2058
132-2052
132-2053
132-2056
151-0001
132-1008
HEX NUT
QTY.
1
1
4
1
1
1
1
6
DESCRIPTION
TOP PLATE
INSIDE FLUSH PLATE
RIB PLATE
END RIB
OUTSIDE FLUSH PLATE
TALL DEFLECTOR MOUNT
SHORT DEFLECTOR MOUNT
3/ ” ⌀ – 16 UNC
8
SEE PAGE
—
—
—
—
—
40
42
—
39
OZZIES
SECTION 2.3.1: TALL DEFLECTOR MOUNT — 151-0001
1
2
3
40
OZZIES
ITEM #
1
2
3
SECTION 2.3.1: TALL DEFLECTOR MOUNT — 151-0001
PART #
151-2001
HEX NUT
151-2002
QTY.
DESCRIPTION
1 PIPE (A53 GRADE B)
1 3/8” ⌀ – 16 UNC
1 THREADED ROD (1020 STEEL)
SEE PAGE
—
—
—
41
OZZIES
SECTION 2.3.2: SHORT DEFLECTOR MOUNT — 132-1008
3
2
1
42
OZZIES
ITEM #
1
2
3
SECTION 2.3.2: SHORT DEFLECTOR MOUNT — 132-1008
PART #
151-2002
HEX NUT
132-2057
QTY.
DESCRIPTION
1 THREADED ROD
1 3/8” ⌀– 16 UNC
1 PIPE (A53 GRADE B)
SEE PAGE
—
—
—
43
OZZIES
SECTION 2.4: LEFT CONVEYOR SHIFT ASSEMBLY
44
OZZIES
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
SECTION 2.4: LEFT CONVEYOR SHIFT ASSEMBLY
PART #
751-9000
HEX BOLT
WASHER
132-0012
151-0002
HEX NUT
WASHER
721-9000
HEX NUT
WASHER
131-9004
132-0005
HEX NUT
WASHER
HEX BOLT
QTY.
2
2
2
2
1
2
2
2
2
2
2
1
4
8
4
DESCRIPTION
CONVEYOR ROLLER PIN
1/ ” ⌀ X 5/ ” LENGTH – 20 UNC
4
8
4
ROLLER PIN HOLDING ASSEMBLY
CONVEYOR ROLLER ASSEMBLY
11/4” ⌀– 12 UNC
11/4” , FLAT, NARROW
GUIDE ROLLER
5/ ” ⌀– 18 UNC
8
8
GUIDE ROLLER
LEFT CONVEYOR SHIFT FRAME ASSEMBLY
3/ ” ⌀–16 UNC
8
8
3/ ” ⌀ X 11/ ” LENGTH – 16 UNC
8
2
SEE PAGE
—
—
—
48
158
—
—
—
—
—
—
46
—
—
—
45
OZZIES
SECTION 2.4.1: LEFT CONVEYOR SHIFT FRAME ASSEMBLY — 132-0005
1
2
3
8
7
6
2
5
4
4
2
9
2
10
1
11
46
OZZIES
ITEM #
1
2
3
4
5
6
7
8
9
10
11
SECTION 2.4.1: LEFT CONVEYOR SHIFT FRAME ASSEMBLY — 132-0005
PART #
HEX BOLT
WASHER
132-2064
HEX NUT
132-2067
132-2063
132-2066
132-2065
132-2060
132-2062
132-2061
QTY.
6
12
1
6
1
2
1
1
1
2
1
1/ ”
2
1/ ”
2
X 13/4”
DESCRIPTION
LENGTH– 13 UNC
⌀
, FLAT, NARROW
REAR FRAME PLATE
1/ ” ⌀– 13 UNC
2
INNER WIPE MOUNT
REAR ROLLER MOUNTING PLATE
RUBBER FLASHING (1/2” X 4”)
OUTER WIPE MOUNT
MOUNTING PLATE
BASE COUPLING PLATE
FRONT FRAME PLATE
SEE PAGE
—
—
—
—
—
—
—
—
—
—
—
47
OZZIES
SECTION 2.4.2: CONVEYOR PIN HOLDING ASSEMBLY — 132-0012
48
OZZIES
ITEM #
1
2
SECTION 2.4.2: CONVEYOR PIN HOLDING ASSEMBLY — 132-0012
PART #
132-2098
132-2099
QTY.
DESCRIPTION
1 PIN HOLDING SLEEVE
1 PIN HOLDING PLATE
SEE PAGE
—
—
49
OZZIES
SECTION 2.5: RIGHT CONVEYOR SHIFT ASSEMBLY
50
OZZIES
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
14
15
—
SECTION 2.5: RIGHT CONVEYOR SHIFT ASSEMBLY
PART #
151-0002
132-0012
751-9000
131-2004
131-9035
131-9018
704-9002
131-9057
131-9050
704-9001
131-9049
131-9034
131-2010
154-9001
154-9002
132-0006
131-9040
QTY.
1
2
2
1
2
2
1
4
1
1
1
4
4
1
1
1
1
DESCRIPTION
CONVEYOR ROLLER PIN
SLIDE DRIVE SHAFT
CONVEYOR SLIDE DRIVE SPROCKET
BEARING
GREASE FITTING (45°, 1/8” , NPT)
SLIDE SPROCKET
4 PIECE COUPLER HOUSING
CONVEYOR SPROCKET CHAIN
SLIDE SPROCKET
MOTOR KEY (5/16” X 11/4” )
CONVEYOR MOTOR TYPE E
CONVEYOR MOTOR TYPE D
RIGHT CONVEYOR SHIFT FRAME ASSEMBLY
BUNDLE OF ITEMS #9 AND #10
SEE PAGE
158
48
—
—
—
—
—
—
—
—
—
—
—
—
52
—
51
OZZIES
SECTION 2.5.1: RIGHT CONVEYOR SHIFT FRAME ASSEMBLY — 132-0006
1
2
3
8
9
4
8
5
7
6
8
2
2
1
8
10
11
10
12
13
2
14
15
16
52
OZZIES
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
SECTION 2.5.1: RIGHT CONVEYOR SHIFT FRAME ASSEMBLY — 132-0006
PART #
HEX BOLT
WASHER
132-2075
132-2145
132-2076
132-2074
132-2068
HEX NUT
132-2144
HEX BOLT
132-2072
132-2071
HEX BOLT
132-2070
132-2073
132-2069
QTY.
8
18
2
1
2
2
1
17
1
4
1
1
5
1
1
1
3/ ”
8
3/ ”
8
X 11/4”
DESCRIPTION
LENGTH – 16 UNC
⌀
, FLAT, REGULAR
WEAR PLATE HOLDER MOUNT
WEAR PLATE HOLDER
WEAR PLATE (1/2” , UHMW)
ROLLER MOUNTING PLATE
FRAME MOUNTING PLATE
3/ ” ⌀– 16 UNC
8
WEAR PLATE HOLDER
3/ ” ⌀ X 11/ ” LENGTH – 16 UNC, CS FLAT HEAD
8
4
SIDE MOUNTING PLATE
WIPER CLAMPING PLATE
3/ ” ⌀ X 11/ ” LENGTH – 16 UNC
8
2
RUBBER WIPER (1/2” X 4”)
SIDE MOUNTING PLATE
MOTOR MOUNTING PLATE
SEE PAGE
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
53
OZZIES
SECTION 2.6: ISOLATOR BRACKET ASSEMBLY — 132-0007
3
2
1
54
OZZIES
ITEM #
1
2
3
SECTION 2.6: ISOLATOR BRACKET ASSEMBLY — 132-0007
PART #
132-2077
132-2078
132-9006
QTY.
DESCRIPTION
1 SQUARE TUBE
1 MOUNT PLATE
1 RUBBER ISOLATOR
SEE PAGE
—
—
—
55
OZZIES
SECTION 2.7: ELEVATOR SPILL PLATE ASSEMBLY — 132-0008
1
2
3
4
5
6
56
OZZIES
ITEM #
1
2
3
4
5
6
SECTION 2.7: ELEVATOR SPILL PLATE ASSEMBLY — 132-0008
PART #
132-2079
PIN
WASHER
132-2080
132-2082
132-2081
QTY.
1
2
2
1
2
1
DESCRIPTION
SPILL PLATE HINGE ROD (1020)
EXTENDED PRONG (3/16” X 2”, SQUARE CUT)
ASTM F436 5/8” , CIRCULAR
SCH40 X 3/4” HINGE PIPE (A53 GRADE B)
TAB
ELEVATOR SPILL PLATE
SEE PAGE
—
—
—
—
—
—
57
OZZIES
SECTION 2.8: LEFT LOWER HEAD PULLEY COVER ASSEMBLY — 132-0010
2
1
58
OZZIES
ITEM #
1
2
SECTION 2.8: LEFT LOWER HEAD PULLEY COVER ASSEMBLY — 132-0010
PART #
132-2096
132-2095
QTY.
DESCRIPTION
1 ROLLER GUARD PLATE LEFT
1 COVER PIPE SECTION (A53 GRADE B)
SEE PAGE
—
—
59
OZZIES
SECTION 2.9: RIGHT LOWER HEAD PULLEY COVER ASSEMBLY — 132-0011
1
2
60
OZZIES
ITEM #
1
2
SECTION 2.9: RIGHT LOWER HEAD PULLEY COVER ASSEMBLY — 132-0011
PART #
132-2097
132-2095
QTY.
DESCRIPTION
1 GUARD PLATE
1 COVER PIPE SECTION (A53 GRADE B)
SEE PAGE
—
—
61
OZZIES
SECTION 2.10: ELEVATOR WIPE ASSEMBLY — 130-0001
1
3
2
4
5
6
7
8
62
OZZIES
ITEM #
1
2
3
4
5
6
7
8
SECTION 2.10: ELEVATOR WIPE ASSEMBLY — 130-0001
PART #
132-2100
HEX BOLT
132-2101
HEX NUT
132-1010
132-1011
704-9003
132-2102
QTY.
2
8
1
8
1
2
2
2
DESCRIPTION
RETAINER PLATE
3/ ” ⌀ X 11/ ” LENGTH – 16 UNC
8
4
WIPER (RUBBER)
3/ ” ⌀– 16 UNC
8
ELEVATOR WIPE FRAME ASSEMBLY
BUSHING HOUSING ASSEMBLY
WIPE SHAFT BUSHING
SEE PAGE
—
—
—
—
66
64
—
—
63
OZZIES
SECTION 2.10.1: BUSHING HOUSING ASSEMBLY — 132-1011
64
OZZIES
ITEM #
1
2
SECTION 2.10.1: BUSHING HOUSING ASSEMBLY — 132-1011
PART #
132-2109
132-2110
QTY.
DESCRIPTION
1 MOUNT PLATE (T-1)
1 PIPE
SEE PAGE
—
—
65
OZZIES
SECTION 2.10.2: ELEVATOR WIPE FRAME ASSEMBLY — 132-1010
66
OZZIES
ITEM #
1
2
3
4
5
6
SECTION 2.10.2: ELEVATOR WIPE FRAME ASSEMBLY — 132-1010
PART #
132-2107
132-2104
132-2105
132-2106
132-2108
132-2103
QTY.
1
1
2
2
2
1
DESCRIPTION
RETAINER PLATE
LONG LENGTH GUSSET
MEDIUM LENGTH GUSSET
SHORT LENGTH GUSSET
SHAFT RETENTION PLATE
HINGE ROD (1020 STEEL)
SEE PAGE
—
—
—
—
—
—
67
OZZIES
SECTION 2.11: ELEVATOR ROLLER WIPE ASSEMBLY — 130-0002
68
OZZIES
ITEM #
1
2
3
4
SECTION 2.11: ELEVATOR ROLLER WIPE ASSEMBLY — 130-0002
PART #
132-2115
132-1012
HEX BOLT
WASHER
QTY.
1
1
5
5
DESCRIPTION
ROLLER WIPER BLADE
ELEVATOR ROLLER WIPER FRAME ASSEMBLY
3/ ” ⌀ X 1” LENGTH – 16 UNC
8
8
SEE PAGE
—
70
—
—
69
OZZIES
SECTION 2.11.1: ELEVATOR ROLLER WIPE FRAME ASSEMBLY — 132-1012
4
5
3
2
1
70
OZZIES
ITEM #
1
2
3
4
5
SECTION 2.11.1: ELEVATOR ROLLER WIPE FRAME ASSEMBLY — 132-1012
PART #
132-2111
132-2112
132-2114
132-2113
HEX NUT
QTY.
1
2
5
1
5
DESCRIPTION
WIPE MOUNTING TUBE
FRAME MOUNTING PLATE
WIPE GUSSET
SUPPORT PLATE
3/ ” ⌀– 16 UNC
8
SEE PAGE
—
—
—
—
—
71
OZZIES
SECTION 3: FRAME ASSEMBLY
6
4
5
3
2
1
7
8
24
9
23
10
22
11
12
13
18
14
21
15
20
19
16
17
72
OZZIES
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
PART #
132-2001
132-1003
132-2023
132-2039
132-2015
134-0001
132-2046
132-1004
HEX BOLT
132-2002
132-2003
132-2013
132-1007
132-2004
132-2017
132-2028
132-1001
132-2045
132-2043
132-2044
132-1002
132-2016
132-2014
132-1005
QTY.
1
1
4
4
1
1
1
1
2
1
2
1
1
2
1
2
1
2
2
2
1
1
1
1
DESCRIPTION
LEFT SIDE PLATE (T-1)
HITCH PLATE ASSEMBLY
RIB PLATE
GUSSET
BACK PLATE
VALVE STACK ASSEMBLY
SUPPORT PLATE
UPPER MOTOR MOUNT ASSEMBLY
1/ ” ⌀ X 21/ ” LENGTH – 20 UNC
4
2
RIGHT SIDE PLATE (T-1)
SKID MOUNT PLATE
RIGHT SKI
LOWER MOTOR MOUNT BOTTOM ASSEMBLY
BOTTOM SKID BAR
RIGHT SKI WEAR PLATE
SCOOP RIB PLATE SPACER
RIGHT SCOOP ASSEMBLY
COVER PLATE
LOWER SHAFT PLATE
SHAFT COVER
LEFT SCOOP ASSEMBLY
LEFT SKI WEAR PLATE
LONG LEFT WEAR PLATE (T-1)
BLADE SUPPORT ASSEMBLY
SEE PAGE
—
78
—
—
—
88
—
80
—
—
—
—
86
—
—
—
74
—
—
—
76
—
—
82
73
OZZIES
SECTION 3.1: RIGHT SCOOP ASSEMBLY — 132-1001
1
3
2
4
6
5
74
OZZIES
ITEM #
1
2
3
4
5
6
SECTION 3.1: RIGHT SCOOP ASSEMBLY — 132-1001
PART #
132-2007
132-2008
132-2005
132-2009
132-2006
132-2010
QTY.
1
1
1
2
1
1
DESCRIPTION
BACKING PLATE
TOP COVER PLATE
SCOOP PLATE
GUSSET PLATE
SIDE PLATE
GUSSET PLATE
SEE PAGE
—
—
—
—
—
—
75
OZZIES
SECTION 3.2: LEFT SCOOP ASSEMBLY — 132-1002
3
2
1
4
5
6
76
OZZIES
ITEM #
1
2
3
4
5
6
SECTION 3.2: LEFT SCOOP ASSEMBLY — 132-1002
PART #
132-2006
132-2008
132-2007
132-2009
132-2010
132-2005
QTY.
1
1
1
2
1
1
DESCRIPTION
BACKING PLATE LEFT SCOOP ASSEMBLY
TOP COVER PLATE LEFT SCOOP ASSEMBLY
SIDE PLATE LEFT SCOOP ASSEMBLY
GUSSET PLATE LEFT SCOOP ASSEMBLY
GUSSET PLATE
SCOOP PLATE LEFT SCOOP ASSEMBLY
SEE PAGE
—
—
—
—
—
—
77
OZZIES
SECTION 3.3: HITCH PLATE ASSEMBLY — 132-1003
1
2
3
4
5
6
78
OZZIES
ITEM #
1
2
3
4
5
6
SECTION 3.3: HITCH PLATE ASSEMBLY — 132-1003
PART #
132-2022
132-2018
HEX NUT
132-2020
132-2019
132-2021
QTY.
1
1
32
1
1
1
DESCRIPTION
TOP HITCH SUPPORT PLATE
HITCH PLATE
3/ ” ⌀– 10 UNC
4
RIB
BOTTOM HITCH SUPPORT PLATE
HITCH BACK PLATE
SEE PAGE
—
—
—
—
—
—
79
OZZIES
SECTION 3.4: UPPER ELEVATOR PULLEY MOTOR MOUNT ASSEMBLY — 132-1004
1
2
3
4
5
6
80
OZZIES
ITEM #
1
2
3
4
5
6
SECTION 3.4: UPPER ELEVATOR PULLEY MOTOR MOUNT ASSEMBLY — 132-1004
PART #
132-2027
132-2026
132-2025
132-2024
WASHER
HEX BOLT
QTY.
4
1
1
1
4
4
DESCRIPTION
GUSSET
BACK PLATE
BOLT PLATE
2
1/ ” ⌀ X 1” LENGTH – 13 UNC
2
SEE PAGE
—
—
—
—
—
—
81
OZZIES
SECTION 3.5: BLADE SUPPORT ASSEMBLY — 132-1005
82
OZZIES
ITEM #
1
2
3
4
5
6
7
8
9
SECTION 3.5: BLADE SUPPORT ASSEMBLY — 132-1005
PART #
132-2029
132-1006
132-2030
132-2031
132-2034
132-2033
132-2035
132-2032
HEX NUT
QTY.
1
2
1
1
4
1
4
1
5
DESCRIPTION
BLADE REAR SUPPORT PLATE (T-1)
BOTTOM SUPPORT SKID POCKET
BLADE TOP SUPPORT PLATE
BLADE FRONT SUPPORT PLATE
FRONT GUSSET
REINFORCING RIB
BACK GUSSET
BOTTOM PLATE
1/ ” ⌀– 13 UNC
2
SEE PAGE
—
84
—
—
—
—
—
—
—
83
OZZIES
SECTION 3.5.1: SUPPORTING ASSEMBLY — 132-1006
2
1
3
84
OZZIES
ITEM #
1
2
3
SECTION 3.5.1: SUPPORTING ASSEMBLY — 132-1006
PART #
132-2037
132-2036
132-2038
QTY.
DESCRIPTION
1 BLADE SUPPORT BASE PLATE
2 BLADE SUPPORT SIDE PLATE
1 BLADE SUPPORT FRONT PLATE
SEE PAGE
—
—
—
85
OZZIES
SECTION 3.6: LOWER ELEVATOR MOTOR BOTTOM MOUNT ASSEMBLY — 132-1007
1
3
2
86
OZZIES
ITEM #
1
2
3
SECTION 3.6: LOWER ELEVATOR MOTOR BOTTOM MOUNT ASSEMBLY — 132-1007
PART #
132-2042
132-2040
132-2041
QTY.
2 SEAT BLOCK
1
BASE PLATE
1 FRONT PLATE
DESCRIPTION
SEE PAGE
—
—
—
87
OZZIES
SECTION 3.7: VALVE STACK ASSEMBLY — 134-0001
1
2
8
3
9
7
4
10
5
11
6
88
OZZIES
ITEM #
1
2
3
4
5
6
7
8
9
10
11
SECTION 3.7: VALVE STACK ASSEMBLY — 134-0001
PART #
134-1001
134-2010
134-2011
134-2002
134-9001
134-2001
134-2004
WASHER
HEX BOLT
134-2003
134-2005
QTY.
1
1
1
1
1
1
2
2
2
1
1
DESCRIPTION
VALVE STACK COVER ASSEMBLY
GAUGE MOUNTING PLATE
SEAT MOUNTING PLATE
MOUNTING CHANNEL
VALVE STACK
BANK SEAT PLATE
SEAT MOUNTING PLATE
8
3/ ” ⌀ X 3/ ” LENGTH – 16 UNC
8
4
VALVE MOUNTING PLATE
VALVE SUPPORT PLATE
SEE PAGE
90
—
—
—
—
—
—
—
—
—
—
89
OZZIES
SECTION 3.7.1: VALVE COVER ASSEMBLY — 134-1001
1
2
3
4
5
6
7
8
90
OZZIES
ITEM #
1
2
3
4
5
6
7
8
SECTION 3.7.1: VALVE COVER ASSEMBLY — 134-1001
PART #
134-2007
134-2009
134-2008
HEX NUT
134-2006
134-2012
WASHER
HEX BOLT
QTY.
1
1
1
4
1
1
4
4
DESCRIPTION
HANDLE
VALVE COVER TOP
ENCLOSURE
1/ ” ⌀– 20 UNC
4
COVER BOLT PLATE
VALVE STACK FRONT COVER
1/ ” ⌀– 20 UNC X 1/ ”
4
2
SEE PAGE
—
—
—
—
—
—
—
—
91
OZZIES
SECTION 4: ELEVATOR ASSEMBLY
1
2
3
4
5
92
OZZIES
ITEM #
1
2
3
4
5
—
—
—
PART #
—
—
—
130-0003
131-9027
131-9056
131-9058
QTY.
1
1
1
1
1
—
—
131-9055
1
—
131-9044
—
DESCRIPTION
ELEVATOR CHAIN & PULLEY ASSEMBLY
UPPER ELEVATOR MOTOR ASSEMBLY
LOWER ELEVATOR MOTOR ASSEMBLY
ELEVATOR BELT ADJUSTER ASSEMBLY
ELEVATOR BELT
ELEVATOR BELT LACING PIN
ELEVATOR BELT LACING PIN GUIDE
ELEVATOR BELT LACING KIT
(INCL. NUTS, BOLTS, PIN, GUIDE, SLEEVE)
ELEVATOR BELT LACING DRILL TEMPLATE
SEE PAGE
98
94
96
108
112
—
—
—
—
93
OZZIES
SECTION 4.1: UPPER ELEVATOR MOTOR ASSEMBLY
1
2
3
5
4
6
7
6
8
9
17
16
10
15
11
19
12
13
14
18
19
20
94
OZZIES
ITEM #
1
2
3
4
5
6
7
8
9
10
11
11
12
13
14
15
16
17
18
19
20
21
—
SECTION 4.1: UPPER ELEVATOR MOTOR ASSEMBLY
PART #
131-0001
704-9002
131-9026
131-9029
704-9001
131-9031
131-9009
131-9002
131-9028
132-1004
134-9002
134-9003
WASHER
HEX NUT
HEX BOLT
HEX BOLT
WASHER
PIN
704-9000
131-9016
131-2013
WASHER
131-9030
QTY.
1
2
1
1
1
1
1
2
1
1
1
1
2
2
2
8
8
2
2
2
2
2
1
DESCRIPTION
BEARING
ELEVATOR CHAIN SPROCKET
ELEVATOR SPROCKET CHAIN
RUBBER SEAL
MOTOR SPROCKET
UPPER MOTOR MOUNT ASSEMBLY
MOTOR TYPE E
MOTOR TYPE D
1/ ” , LOCK
2
1/ ” ⌀– 13 UNC
2
1/ ” ⌀ X 2” LENGTH – 13 UNC, CS (66°, 0.89”)
2
1/ ” ⌀ X 23/ ” LENGTH – 13 UNC
2
4
2
EXTENDED PRONG (1/4” X 11/2” , SQUARE CUT)
BEARING
ELEVATOR IDLER SPACER
11/2” , FLAT, NARROW
SEE PAGE
98
—
—
—
—
—
—
—
—
80
—
—
—
—
—
—
—
—
—
—
—
—
—
95
OZZIES
SECTION 4.2: LOWER ELEVATOR MOTOR ASSEMBLY
96
OZZIES
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
12
13
14
15
16
17
18
19
20
21
22
23
24
—
SECTION 4.2: LOWER ELEVATOR MOTOR ASSEMBLY
PART #
131-0001
131-2008
HEX BOLT
WASHER
704-9000
704-9001
131-9031
131-9009
131-9002
131-9028
131-2005
134-9002
134-9003
130-0007
WASHER
HEX BOLT
HEX NUT
WASHER
HEX BOLT
131-9029
HEX BOLT
131-9026
131-2006
130-0008
131-2037
131-9030
QTY.
1
1
2
2
2
1
1
1
2
1
1
1
1
1
12
4
2
2
2
1
8
2
2
1
2
1
DESCRIPTION
MOTOR GUARD BACK PLATE
3/ ” ⌀ X 1” LENGTH– 16 UNC
8
8
ELEVATOR SPROCKET CHAIN
RUBBER SEAL
MOTOR SPROCKET
MOUNTING PLATE
MOTOR TYPE E
MOTOR TYPE D
LOWER ELEVATOR MOTOR SHIELD ASSEMBLY
2
1/ ” ⌀ X 11/ ” LENGTH – 13 UNC
2
2
1/ ” ⌀– 13 UNC
2
1/ ” , LOCK
2
1/ ” ⌀ X 2” LENGTH – 13 UNC, CS (66°, 0.89”)
2
ELEVATOR CHAIN SPROCKET
1/ ” ⌀ X 23/ ” LENGTH – 13 UNC
2
4
BEARING
SEAT BLOCK
LOWER ELEVATOR MOTOR TOP COVER ASSEMBLY
ROLLER BEARING KEY (1/2” X 31/12” )
SEE PAGE
98
—
—
—
—
—
—
—
—
—
—
—
—
26
—
—
—
—
—
—
—
—
—
28
—
—
97
OZZIES
SECTION 4.3: ELEVATOR CHAIN & PULLEY ASSEMBLY
2
1
3
4
98
OZZIES
ITEM #
1
1
1
1
2
3
4
SECTION 4.3: ELEVATOR CHAIN & PULLEY ASSEMBLY
PART #
131-1005
131-1006
131-1007
131-1008
131-1002
131-1004
131-1003
QTY.
1
1
1
1
1
1
1
DESCRIPTION
3/ ” PRODUCING ELEVATOR CHAIN WITH FLIGHTS
8
8
8
11/2” PRODUCING ELEVATOR CHAIN WITH FLIGHTS
UPPER ELEVATOR PULLEY ASSEMBLY
ELEVATOR SLACK PULLEY ASSEMBLY
LOWER ELEVATOR HEAD PULLEY ASSEMBLY
SEE PAGE
100
100
100
100
104
102
106
99
OZZIES
SECTION 4.3.1: ELEVATOR CHAINS WITHOUT FLIGHTS ATTACHED
2
1
100
OZZIES
ITEM #
1
1
1
1
2
SECTION 4.3.1: ELEVATOR CHAINS WITHOUT FLIGHTS ATTACHED
PART #
131-9051
131-9052
131-9053
131-9054
131-2023
QTY.
1
1
1
1
29
DESCRIPTION
SEE PAGE
PRODUCING ELEVATOR CHAIN (1/2” X 13' 6”)
—
PRODUCING ELEVATOR CHAIN (1” X 13' 6”)
—
PRODUCING ELEVATOR CHAIN (11/4” X 13' 6”)
—
1
3
1 /2” PRODUCING ELEVATOR CHAIN (1 /4” X 13' 6”)
—
ELEVATOR FLIGHT
—
3/ ”
8
5/ ”
8
7/ ”
8
101
OZZIES
SECTION 4.3.2: ELEVATOR SLACK PULLEY ASSEMBLY — 131-1004
1
2
102
OZZIES
ITEM #
1
2
SECTION 4.3.2: ELEVATOR SLACK PULLEY ASSEMBLY — 131-1004
PART #
131-9001
131-2018
QTY.
DESCRIPTION
1 CHAIN IDLE SHAFT
1 CHAIN IDLE ROLLER
SEE PAGE
—
—
103
OZZIES
SECTION 4.3.3: UPPER ELEVATOR PULLEY ASSEMBLY— 131-1002
1
7
6
5
4
3
2
104
OZZIES
ITEM #
1
2
3
4
5
6
7
SECTION 4.3.3: UPPER ELEVATOR PULLEY ASSEMBLY— 131-1002
PART #
131-2016
131-2012
HEX BOLT
131-2030
131-2029
131-2017
131-2028
QTY.
1
2
4
2
2
2
1
DESCRIPTION
UPPER PULLEY SHAFT
ROLLER BEARING KEY (1/2” X 31/12” )
1/ ” ⌀ X 1” LENGTH – 13 UNC, HEX HEAD CAP
2
TAPER-LOCK BUSHING
TAPER-LOCK WELD ON HUB
PULLEY FLANGE END KIT
UPPER ELEVATOR PULLEY ROLLER (VULCANIZED)
SEE PAGE
—
—
—
—
—
—
—
105
OZZIES
SECTION 4.3.4: LOWER ELEVATOR HEAD PULLEY ASSEMBLY — 131-1003
1
4
3
2
106
OZZIES
ITEM #
1
2
3
4
SECTION 4.3.4: LOWER ELEVATOR HEAD PULLEY ASSEMBLY — 131-1003
PART #
131-2020
131-2022
131-2021
131-2019
QTY.
1
2
2
1
DESCRIPTION
LOWER PULLEY SHAFT
LOWER PULLEY END CAP
LOWER PULLEY PIPE
LOWER PULLEY GROOVE
SEE PAGE
—
—
—
—
107
OZZIES
SECTION 4.4: ELEVATOR BELT ADJUSTER ASSEMBLY — 130-0003
2
3
1
4
5
6
7
8
108
OZZIES
ITEM #
1
2
3
4
5
6
7
8
SECTION 4.4: ELEVATOR BELT ADJUSTER ASSEMBLY — 130-0003
PART #
131-9033
704-9000
131-9016
132-2116
132-1015
131-9043
704-9004
HEX BOLT
QTY.
1
2
2
1
1
2
2
4
DESCRIPTION
ELEVATOR BELT IDLER ROLLER
BEARING
ROLLER WIPER
ROLLER WIPER FRAME ASSEMBLY
ELEVATOR FRICTION DRIVE BELT TELESCOPER
1/ ” ⌀ X 1” LENGTH – 13 UNC
2
SEE PAGE
—
—
—
—
110
—
—
—
109
OZZIES
SECTION 4.4.1: BELT ADJUSTER FRAME — 132-1015
2
1
110
OZZIES
ITEM #
1
2
SECTION 4.4.1: BELT ADJUSTER FRAME — 132-1015
PART #
132-2122
132-2123
QTY.
1 TUBE
2 LINK PLATE
DESCRIPTION
SEE PAGE
—
—
111
OZZIES
SECTION 4.5: ELEVATOR BELT – 131-9027
112
OZZIES
SECTION 4.5: ELEVATOR BELT – 131-9027
ITEM #
1
2
PART #
751-9001
131-9056
3
131-9055
4
—
—
131-9027
131-9058
131-9044
QTY.
DESCRIPTION
2 HINGE PIN CLIP
— ELEVATOR BELT LACING PIN
ELEVATOR BELT LACING KIT
1
1 ELEVATOR BELT
— ELEVATOR BELT LACING PIN GUIDE
— ELEVATOR BELT LACING DRILL TEMPLATE
SEE PAGE
—
—
112
—
—
113
OZZIES
SECTION 5: VIBRATOR ASSEMBLY
1
4
3
5
2
6
114
OZZIES
ITEM #
1
2
3
4
5
6
PART #
—
HEX NUT
WASHER
HEX BOLT
132-0007
132-0009
QTY.
1
16
32
16
4
1
DESCRIPTION
VIBRATOR SHAFT ASSEMBLY
1/ ” ⌀ – 13 UNC
2
2
1/ ” ⌀ X 11/ ” LENGTH – 13 UNC
2
2
ISOLATOR BRACKET ASSEMBLY
VIBRATOR FRAME ASSEMBLY
SEE PAGE
116
—
—
—
54
118
115
OZZIES
SECTION 5.1: VIBRATOR SHAFT ASSEMBLY
12
11
10
9
8
7
6
5
4
3
2
1
116
OZZIES
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
SECTION 5.1: VIBRATOR SHAFT ASSEMBLY
PART #
HEX BOLT
WASHER
131-9014
132-1009
HEX NUT
131-9013
131-9012
131-9011
704-9000
131-9025
131-9015
132-2093
QTY.
2
2
1
1
2
1
1
1
2
2
1
1
7/ ”
16
7/ ”
16
X 13/4”
DESCRIPTION
LENGTH– 14 UNC
⌀
, FLAT, NARROW
MOTOR TYPE E
VIBRATOR MOTOR BRACKET ASSEMBLY
7/ ” ⌀– 14 UNC
16
MOTOR COUPLING HUB
FLEX COUPLING
SHAFT COUPLING HUB
BEARING
VIBRATOR KEY (1/4” X 11/2” )
WEIGHTED SHAFT ASSEMBLY
SEE PAGE
—
—
—
120
—
—
—
—
—
—
—
122
117
OZZIES
SECTION 5.2: VIBRATOR FRAME ASSEMBLY — 132-0009
118
OZZIES
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
SECTION 5.2: VIBRATOR FRAME ASSEMBLY — 132-0009
PART #
WASHER
HEX BOLT
132-2083
131-1001
HEX BOLT
WASHER
704-9002
HEX NUT
132-2084
132-2085
132-2094
HEX BOLT
132-1009
132-2088
132-2086
132-2092
131-9016
132-2093
QTY.
8
8
1
2
14
36
4
18
2
4
8
4
1
2
2
2
4
1
DESCRIPTION
1/ ”
2
1/ ”
2
, FLAT, NARROW
⌀ X 11/2” LENGTH– 13 UNC
LONG SQUARE TUBE
VIBRATOR ROLLER ASSEMBLY
1/ ” ⌀ X 33/ ” LENGTH – 13 UNC
2
4
1/ ” ⌀– 13 UNC
2
SHORT SQUARE TUBE
FRAME MOUNT PLATE
VIBRATOR FRAME GUSSET
1/ ” ⌀ X 31/ ” LENGTH– 13 UNC
2
4
VIBRATOR MOTOR BRACKET ASSEMBLY
BEARING MOUNTING PLATE
COVER PLATE
BEARING
WEIGHTED SHAFT ASSEMBLY
SEE PAGE
—
—
—
—
—
—
—
—
—
—
—
—
120
—
—
—
—
122
119
OZZIES
SECTION 5.3: VIBRATOR MOTOR BRACKET ASSEMBLY — 132-1009
1
2
3
120
OZZIES
ITEM #
1
2
3
SECTION 5.3: VIBRATOR MOTOR BRACKET ASSEMBLY — 132-1009
PART #
132-2089
132-2091
132-2090
QTY.
DESCRIPTION
1 VIBRATOR FRAME MOUNTING PLATE
2 SIDE PLATE
1 MOTOR MOUNTING PLATE
SEE PAGE
—
—
—
121
OZZIES
SECTION 5.4 WEIGHTED SHAFT ASSEMBLY — 132-2093
1
2
3
122
OZZIES
ITEM #
1
2
3
SECTION 5.4 WEIGHTED SHAFT ASSEMBLY — 132-2093
PART #
131-2025
131-2026
131-2027
QTY.
1 SHAFT
2 DONUT
1 PIPE
DESCRIPTION
SEE PAGE
—
—
—
123
OZZIES
SECTION 6: CONVEYOR ASSEMBLY
2
3
1
4
5
6
7
9
8
10
11
12
13
16
14
15
124
OZZIES
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PART #
152-1005
HEX NUT
WASHER
152-2017
152-2018
152-2046
HEX BOLT
152-1006
HEX BOLT
WASHER
152-1004
152-2007
152-1003
152-1002
152-1001
152-2041
QTY.
1
2
2
2
2
2
2
1
26
26
1
9
1
1
1
2
DESCRIPTION
FRONT LEFT DEFLECTOR ASSEMBLY
1/ ” ⌀– 13 UNC
2
2
HINGE TAB
HINGE TAB
HINGE TAB
1/ ” ⌀ X 11/ ” LENGTH – 13 UNC, CS (66°, 0.89”)
2
2
BACK LEFT DEFLECTOR ASSEMBLY
3/ ” ⌀ X 11/ ” LENGTH – 16 UNC
8
2
8
FRONT RIGHT DEFLECTOR ASSEMBLY
CONVEYOR INNER BRACE TUBE
BACK RIGHT DEFLECTOR ASSEMBLY
BACK FRAME ASSEMBLY
FRONT FRAME ASSEMBLY
CONVEYOR STOP
SEE PAGE
144
—
—
—
—
—
—
148
—
—
142
—
146
140
138
—
125
OZZIES
SECTION 6: CONVEYOR VIEW 2 OF 6
126
OZZIES
ITEM #
1
1
2
3
4
5
6
7
PART #
154-9001
154-9002
HEX BOLT
152-2029
704-9001
131-9018
152-2050
151-0003
QTY.
1
1
4
1
1
2
1
1
DESCRIPTION
MOTOR TYPE E
MOTOR TYPE D
3
/8” ⌀ X 11/4” LENGTH – 16 UNC, HEX HEAD CAP
CONVEYOR MOTOR COUPLING
BEARING
CONVEYOR PULLEY KEY (1/4” X 23/4”)
HEAD PULLEY ASSEMBLY
SEE PAGE
—
—
—
—
—
—
—
156
127
OZZIES
128
OZZIES
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
PART #
751-9000
HEX BOLT
WASHER
132-0012
HEX BOLT
WASHER
152-2028
152-1009
HEX BOLT
WASHER
152-2043
152-2039
HEX NUT
HEX NUT
152-2012
152-2013
152-2011
151-0002
QTY.
8
2
2
10
8
8
2
1
2
2
2
1
2
4
1
1
1
4
DESCRIPTION
CONVEYOR ROLLER PIN
1/ ” ⌀ X 5/ ” LENGTH – 20 UNC
4
8
4
3/ ” ⌀ X 11/ ” LENGTH – 16 UNC
8
4
RIGHT MOTOR MOUNTING ASSEMBLY
1/ ” ⌀ X 11/ ” LENGTH – 13 UNC
2
2
2
PULLEY WIPE MOUNTING PLATE
PULLEY WIPE PLATE
1/ ” ⌀– 13 UNC
2
3/ ” ⌀– 16 UNC
8
WIPE RUBBER
WIPER FASTENING PLATE
SEE PAGE
—
—
—
48
—
—
—
152
—
—
—
—
—
—
—
—
—
158
129
OZZIES
130
OZZIES
ITEM #
1
1
2
3
4
5
6
7
8
9
10
11
PART #
154-9001
154-9002
HEX BOLT
152-2029
152-2050
151-0003
704-9001
131-9018
132-9001
WASHER
HEX BOLT
704-9004
QTY.
1
1
4
1
1
1
2
2
2
4
4
2
DESCRIPTION
MOTOR TYPE E
MOTOR TYPE D
3/ ” ⌀ X 11/ ” LENGTH – 16 UNC, HEX HEAD CAP
8
4
CONVEYOR MOTOR COUPLING CLAMP
HEAD PULLEY ASSEMBLY
BEARING
BELT ADJUSTER ASSEMBLY
1/ ” ⌀ X 1” LENGTH – 13 UNC
2
SEE PAGE
—
—
—
—
—
156
—
—
—
—
—
—
131
OZZIES
1
2
3
4
5
2
6
7
8
9
10
11
9
12
132
OZZIES
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
PART #
HEX NUT
WASHER
152-2014
152-2015
152-2016
HEX BOLT
152-1008
HEX NUT
WASHER
152-2040
152-1010
HEX BOLT
QTY.
4
8
1
1
1
4
1
4
2
1
2
2
DESCRIPTION
3/ ”
8
3/ ”
8
⌀– 16 UNC
, FLAT, NARROW
WIPER FASTENING PLATE
RUBBER WIPER
3/ ” ⌀ X 11/ ” LENGTH – 16 UNC
8
2
MOTOR MOUNT ASSEMBLY
1/ ” ⌀– 13 UNC
2
2
PULLEY WIPE PLATE
PULLEY WIPER MOUNT ASSEMBLY
1/ ” ⌀ X 21/ ” LENGTH – 13 UNC
2
4
SEE PAGE
—
—
—
—
—
—
150
—
—
—
154
—
133
OZZIES
134
OZZIES
ITEM #
1
2
3
4
5
—
—
PART #
152-2048
151-9005
HEX BOLT
WASHER
HEX BOLT
151-9012
—
—
151-9006
151-9011
151-9007
QTY.
2
1
2
2
2
—
—
—
—
FLASHING (1/2” X
DESCRIPTION
4”,RUBBER)
BELT
1/ ” ⌀ X 11/ ” LENGTH – 13 UNC, CS (66°, 0.89”)
2
2
2
1/ ” ⌀– 13 UNC
2
LACING DRILL TEMPLATE
LACING KIT
LACING PIN
LACING PIN GUIDE
SEE PAGE
—
136
—
—
—
—
—
—
—
135
OZZIES
SECTION 6.1: CONVEYOR BELT — 151-9005
136
OZZIES
SECTION 6.1: CONVEYOR BELT — 151-9005
ITEM #
1
2
PART #
151-9005
751-9001
3
151-9007
4
—
—
151-9006
151-9012
151-9011
QTY.
DESCRIPTION
1 BELT
2 HINGE PIN CLIP
LACING KIT
1
1 LACING PIN
— LACING DRILL TEMPLATE
— LACING PIN GUIDE
SEE PAGE
—
—
—
—
—
137
OZZIES
SECTION 6.2: CONVEYOR FRONT FRAME ASSEMBLY — 152-1001
6
7
1
2
3
4
5
138
OZZIES
ITEM #
1
2
3
4
5
6
7
SECTION 6.2: CONVEYOR FRONT FRAME ASSEMBLY — 152-1001
PART #
152-2005
HEX NUT
152-2002
152-2006
152-2004
152-2001
152-2003
QTY.
1
13
1
1
1
1
2
DESCRIPTION
TOP RIB
3/ ” ⌀– 16 UNC
8
RIGHT FRONT RIB
BASE PLATE
SLIDE RACK
LEFT FRONT RIB
HOLD TAB
SEE PAGE
—
—
—
—
—
—
—
139
OZZIES
SECTION 6.3: CONVEYOR BACK FRAME ASSEMBLY — 152-1002
7
1
6
2
3
5
4
140
OZZIES
ITEM #
1
2
3
4
5
6
7
SECTION 6.3: CONVEYOR BACK FRAME ASSEMBLY — 152-1002
PART #
152-2010
HEX NUT
152-2009
152-2006
152-2004
152-2003
152-2008
QTY.
1
13
1
1
1
2
1
DESCRIPTION
TOP RIB
3/ ” ⌀– 16 UNC
8
RIGHT BACK RIB
BASE PLATE
SLIDE RACK
HOLD TAB
LEFT BACK RIB
SEE PAGE
—
—
—
—
—
—
—
141
OZZIES
SECTION 6.4: FRONT RIGHT DEFLECTOR ASSEMBLY — 152-1004
5
4
2
1
3
142
OZZIES
ITEM #
1
2
3
4
5
SECTION 6.4: FRONT RIGHT DEFLECTOR ASSEMBLY — 152-1004
PART #
152-2019
152-2020
151-0001
152-2021
152-2022
QTY.
1
1
1
1
1
DESCRIPTION
MOUNTING PLATE
VERTICAL RIB
FLASHING BASE PLATE
FLASHING RETAINER
SEE PAGE
—
—
40
—
—
143
OZZIES
SECTION 6.5: FRONT LEFT DEFLECTOR ASSEMBLY — 152-1005
5
3
4
2
1
144
OZZIES
ITEM #
1
2
3
4
5
SECTION 6.5: FRONT LEFT DEFLECTOR ASSEMBLY — 152-1005
PART #
152-2023
152-2024
151-0001
152-2025
152-2026
QTY.
1
1
1
1
1
DESCRIPTION
MOUNTING PLATE
VERTICAL RIB
FLASHING BASE PLATE
FLASHING RETAINER
SEE PAGE
—
—
40
—
—
145
OZZIES
SECTION 6.6: BACK RIGHT DEFLECTOR ASSEMBLY — 152-1003
2
3
1
4
5
146
OZZIES
ITEM #
1
2
3
4
5
SECTION 6.6: BACK RIGHT DEFLECTOR ASSEMBLY — 152-1003
PART #
151-0001
152-2019
152-2020
152-2021
152-2022
QTY.
1
1
1
1
1
DESCRIPTION
MOUNTING PLATE
VERTICAL RIB
FLASHING BASE PLATE
FLASHING RETAINER
SEE PAGE
40
—
—
—
—
147
OZZIES
SECTION 6.7: BACK LEFT DEFLECTOR ASSEMBLY — 152-1006
3
1
2
4
5
148
OZZIES
ITEM #
1
2
3
4
5
SECTION 6.7: BACK LEFT DEFLECTOR ASSEMBLY — 152-1006
PART #
152-2023
152-2024
151-0001
152-2025
152-2026
QTY.
1
1
1
1
1
DESCRIPTION
MOUNTING PLATE
VERTICAL RIB
FLASHING BASE PLATE
FLASHING RETAINER
SEE PAGE
—
—
40
—
—
149
OZZIES
SECTION 6.8: CONVEYOR LEFT MOTOR MOUNT ASSEMBLY — 152-1008
1
3
2
4
150
OZZIES
ITEM #
1
2
3
4
SECTION 6.8: CONVEYOR LEFT MOTOR MOUNT ASSEMBLY — 152-1008
PART #
152-2035
152-2036
152-2037
152-2038
QTY.
1
1
1
2
DESCRIPTION
BASE PLATE
RIB
ALIGNMENT TAB
SEE PAGE
—
—
—
—
151
OZZIES
SECTION 6.9: RIGHT MOTOR MOUNTING ASSEMBLY— 152-1009
1
2
3
4
152
OZZIES
ITEM #
1
2
3
4
SECTION 6.9: RIGHT MOTOR MOUNTING ASSEMBLY— 152-1009
PART #
152-2035
152-2037
152-2036
152-2038
QTY.
1
1
1
2
DESCRIPTION
RIB
BASE PLATE
ALIGNMENT TAB
SEE PAGE
—
—
—
—
153
OZZIES
SECTION 6.10: PULLEY WIPER MOUNT ASSEMBLY — 152-1010
2
1
154
OZZIES
ITEM #
1
2
SECTION 6.10: PULLEY WIPER MOUNT ASSEMBLY — 152-1010
PART #
152-2044
152-2045
QTY.
1 PIPE
1 PLATE
DESCRIPTION
SEE PAGE
—
—
155
OZZIES
SECTION 6.11: HEAD PULLEY ASSEMBLY — 151-0003
1
2
3
4
5
156
OZZIES
SECTION 6.11: HEAD PULLEY ASSEMBLY — 151-0003
ITEM #
1
2
3
4
5
PART #
151-9002
151-9003
151-9004
151-2009
HEX BOLT
QTY.
1
1
2
2
4
—
151-0005
1
DESCRIPTION
PULLEY SHAFT
HEAD PULLEY
TAPER-LOCK BUSHING
3/ ” ⌀ X 5/ ” LENGTH– 16 UNC, HEX SET SCREW
8
8
CONVEYOR HEAD PULLEY GROUP
GROUP OF ITEMS #2, 3, 4 & 5
SEE PAGE
—
—
—
—
—
157
OZZIES
SECTION 6.12: CONVEYOR ROLLER ASSEMBLY — 151-0002
1
2
158
OZZIES
ITEM #
1
2
SECTION 6.12: CONVEYOR ROLLER ASSEMBLY — 151-0002
PART #
151-9001
151-9000
QTY.
DESCRIPTION
1 CONVEYOR ROLLER
2 SINGLE ROW BEARING
SEE PAGE
—
—
159
OZZIES
SECTION 7: ADDITIONAL LOADER, ELECTRICAL AND PADDER PARTS NOT SHOWN IN VIEWS
PART #
104-1000
104-9001
104-9002
124-9004
124-9005
131-9041
131-9042
134-9007
134-9008
172-1000
172-2001
174-9000
174-9001
174-9002
174-9003
175-9000
175-9001
175-9002
175-9003
175-9004
175-9005
185-2001
701-9000
701-9001
701-9002
701-9003
701-9004
701-9005
714-9000
785-9001
785-9002
785-9003
785-9004
785-9005
785-9006
785-9007
160
DESCRIPTION
RADIATOR MOUNT
MASTER HITCH CYLINDER
SHUTTLE VALVE
LOADER FLOW DISTRIBUTION HYDRAULIC BLOCK
KAT MASTER HITCH 755C
PROP. COIL FOR VALVE STACK PVG
PRESSURE GAUGE
DAMAN HEADER MANIFOLD 90°, CASE DRAIN
REBUILT VALVE STACK CVA-8572
SIDE PLUG BULKHEAD
CONTROL BOX DASH PLATE
4 WAY 3 POSITION CARTRIDGE VALVE
VICKERS SOLENOID VALVE
TTP HEAT EXCHANGER (MP)
FAN MOTOR COMBO (FOR 174-9002)
VICKERS DEUTSCH 24VDC COIL
24 VOLT COIL W/ WIRE LEADS
HYDRAFORCE IRON BODY
CARTRIDGE VALVE BODY
ETI JOYSTICK ROCKER POT
RAM MOUNT
CONTROL BOX TO SD1 HARNESS
8" WIDE FLASHING PER FOOT
4" WIDE BULLDOG FLASHING PER FOOT
8" WIDE BULLDOG FLASHING PER FOOT
HIGH PRESSURE FILTER, 90GPM, 20µ
SAUER DANFOSS MC024-020 MICRO CONTROLLER
1/ " STUCCI FEMALE QUICK COULPING
2
1/ " STUCCI MALE QUICK COUPLING
2
1” STUCCI FEMALE QUICK COULPING
1” STUCCI MALE QUICK COUPLING
11/4" STUCCI FEMALE QUICK COULPING
11/4" STUCCI MALE QUICK COUPLING
SECTION 7: ADDITIONAL LOADER, ELECTRICAL AND PADDER PARTS NOT SHOWN IN VIEWS
OZZIES
INDEX OF PART NUMBERS
102-1001 ............... 17, 18, 19
131-2020 ........................ 107
131-9055....................93, 113
102-2001 ...........................19
131-2021 ........................ 107
131-9056....................93, 113
102-2002 ...........................19
131-2022 ........................ 107
131-9057........................... 51
102-2003 ...........................19
131-2023 ........................ 101
131-9058....................93, 113
102-2004 ...........................19
131-2025 ........................ 123
132-0002................ 33, 34, 35
102-2005 ...........................19
131-2026 ........................ 123
132-0003................ 31, 36, 37
102-2006 ...........................19
131-2027 ........................ 123
132-0004................ 31, 38, 39
104-1000 ......................... 160
131-2028 ........................ 105
132-0005................ 45, 46, 47
104-9001 ......................... 160
131-2029 ........................ 105
132-0006................ 51, 52, 53
104-9002 ......................... 160
131-2030 ........................ 105
132-0007.........33, 54, 55, 115
124-9004 ......................... 160
131-2034 .......................... 31
132-0008................ 33, 56, 57
124-9005 ......................... 160
131-2035 .......................... 31
132-0009.................. 115, 119
130-0001 ............... 31, 62, 63
131-2037 .......................... 97
132-0010................ 31, 58, 59
130-0002 ............... 31, 68, 69
131-9001 ........................ 103
132-0011................ 31, 60, 61
130-0003 ............ 93, 108, 109
131-9002 ..................... 95, 97
130-0004 ............... 17, 24, 25
131-9004 .......................... 45
132-0012......... 45, 48, 49, 51,
.................................. 129
130-0005 ............... 17, 20, 21
131-9009 ..................... 95, 97
132-1001................ 73, 74, 75
130-0006 ............... 17, 22, 23
131-9011 ........................ 117
132-1002.........73, 76, 77, 105
130-0007 .......... 17, 26, 27, 97
131-9012 ........................ 117
132-1003.........73, 78, 79, 107
130-0008 .......... 17, 28, 29, 97
131-9013 ........................ 117
132-1004.......... 73, 80, 81, 95
131-0001 ............... 95, 97, 99
131-9014 ........................ 117
132-1005................ 73, 82, 83
131-0004 ......................... 103
131-9015 ........................ 117
132-1006................ 83, 84, 85
131-1001 ......................... 119
131-9016 ...... 17, 95, 109, 119
132-1007................ 73, 86, 87
131-1002 ................... 99, 104
131-9018 ............ 51, 127, 131
132-1008................ 39, 42, 43
131-1003 ................... 99, 106
131-9025 ........................ 117
131-1004 ...........................99
131-9026 ..................... 95, 97
132-1009..........117, 119, 120,
................................... 121
131-1005 ...........................99
131-9027 ................... 93, 113
131-1006 ...........................99
131-9028 ..................... 95, 97
131-1007 ...........................99
131-9029 ..................... 95, 97
131-1008 ...........................99
131-9030 ..................... 95, 97
131-2002 ...........................33
131-9031 ..................... 95, 97
131-2003 ...........................33
131-9033 ........................ 109
131-2004 ...........................51
131-9034 .......................... 51
131-2005 ...........................97
131-9035 .......................... 51
131-2006 ...........................97
131-9040 .......................... 51
131-2007 ...........................31
131-9041 ........................ 160
131-2008 ...........................97
131-9042 ........................ 160
131-2009 ...........................31
131-9043 ........................ 109
131-2010 ...........................51
131-9044 ................... 93, 113
131-2012 ......................... 105
131-9049 .......................... 51
131-2013 ...........................95
131-9050 .......................... 51
131-2016 ......................... 105
131-9051 ........................ 101
131-2017 ......................... 105
131-9052 ........................ 101
131-2018 ......................... 103
131-9053 ........................ 101
131-2019 ......................... 107
131-9054 ........................ 101
132-1010................ 63, 66, 67
132-1011................ 63, 64, 65
132-1012................ 69, 70, 71
132-1015...........109, 110, 111
132-2001........................... 73
132-2002........................... 73
132-2003........................... 73
132-2004........................... 73
132-2005..................... 75, 77
132-2006..................... 75, 77
132-2007..................... 75, 77
132-2008..................... 75, 77
132-2009..................... 75, 77
132-2010..................... 75, 77
132-2013........................... 73
132-2014........................... 73
132-2015........................... 73
132-2016........................... 73
132-2017........................... 73
161
OZZIES
132-2018 ...........................79
132-2066 .......................... 47
132-2113........................... 71
132-2019 ...........................79
132-2067 .......................... 47
132-2114........................... 71
132-2020 ...........................79
132-2068 .......................... 53
132-2115........................... 69
132-2021 ...........................79
132-2069 .......................... 53
132-2116......................... 109
132-2022 ...........................79
132-2070 .......................... 53
132-2122......................... 111
132-2023 ...........................73
132-2071 .......................... 53
132-2123......................... 111
132-2024 ...........................81
132-2072 .......................... 53
132-2124..................... 21, 25
132-2025 ...........................81
132-2073 .......................... 53
132-2125..................... 21, 25
132-2026 ...........................81
132-2074 .......................... 53
132-2126..................... 21, 25
132-2027 ...........................81
132-2075 .......................... 53
132-2127..................... 21, 25
132-2028 ...........................73
132-2076 .......................... 53
132-2128..................... 21, 25
132-2029 ...........................83
132-2077 .......................... 55
132-2129..................... 21, 25
132-2030 ...........................83
132-2078 .......................... 55
132-2130..................... 21, 25
132-2031 ...........................83
132-2079 .......................... 57
132-2131..................... 21, 25
132-2032 ...........................83
132-2080 .......................... 57
132-2132..................... 21, 25
132-2033 ...........................83
132-2081 .......................... 57
132-2133..................... 21, 25
132-2034 ...........................83
132-2082 .......................... 57
132-2134..................... 21, 25
132-2035 ...........................83
132-2083 ........................ 119
132-2135..................... 21, 25
132-2036 ...........................85
132-2084 ........................ 119
132-2136........................... 23
132-2037 ...........................85
132-2085 ........................ 119
132-2137........................... 23
132-2038 ...........................85
132-2086 ........................ 119
132-2138........................... 27
132-2039 ...........................73
132-2088 ........................ 119
132-2139........................... 27
132-2040 ...........................87
132-2089 ........................ 121
132-2140........................... 27
132-2041 ..................... 29, 87
132-2090 ........................ 121
132-2141........................... 27
132-2042 ...........................87
132-2091 ........................ 121
132-2142........................... 29
132-2043 ...........................73
132-2092 ........................ 119
132-2143........................... 29
132-2044 ...........................73
132-2144........................... 53
132-2045 ...........................73
132-2093 ......... 117, 119, 122,
.................................. 123
132-2046 ...........................73
132-2094 ........................ 119
132-2146........................... 33
132-2047 ...........................35
132-2095 ..................... 59, 61
132-2147........................... 31
132-2048 ...........................35
132-2096 .......................... 59
132-9001......................... 131
132-2049 ...........................35
132-2097 .......................... 61
132-9005..................... 21, 25
132-2050 ...........................37
132-2098 .......................... 49
132-9006........................... 55
132-2051 ...........................37
132-2099 .......................... 49
134-0001................ 73, 88, 89
132-2052 ..................... 37, 39
132-2100 .......................... 63
134-1001................ 89, 90, 91
132-2053 ..................... 37, 39
132-2101 .......................... 63
134-2001........................... 89
132-2054 ...........................37
132-2102 .......................... 63
134-2002........................... 89
132-2055 ...........................39
132-2103 .......................... 67
134-2003........................... 89
132-2056 ...........................39
132-2104 .......................... 67
134-2004........................... 89
132-2057 ...........................43
132-2105 .......................... 67
134-2005........................... 89
132-2058 ...........................39
132-2106 .......................... 67
134-2006........................... 91
132-2060 ...........................47
132-2107 .......................... 67
134-2007........................... 91
132-2061 ...........................47
132-2108 .......................... 67
134-2008........................... 91
132-2062 ...........................47
132-2109 .......................... 65
134-2009........................... 91
132-2063 ...........................47
132-2110 .......................... 65
134-2010........................... 89
132-2064 ...........................47
132-2111 .......................... 71
134-2011........................... 89
132-2065 ...........................47
132-2112 .......................... 71
134-2012........................... 91
162
132-2145........................... 53
OZZIES
134-9001 ...........................89
152-2007 ........................ 125
172-2001......................... 160
134-9002 ..................... 95, 97
152-2008 ........................ 141
174-9000......................... 160
134-9003 ..................... 95, 97
152-2009 ........................ 141
174-9001......................... 160
134-9007 ......................... 160
152-2010 ........................ 141
174-9002......................... 160
134-9008 ......................... 160
152-2011 ........................ 129
174-9003......................... 160
151-0001 ....... 39, 40, 41, 143,
.................... 145, 147, 149
152-2012 ........................ 129
175-9000......................... 160
152-2013 ........................ 129
175-9001......................... 160
151-0002 ..... 45, 51, 129, 158,
................................... 159
152-2014 ........................ 133
175-9002......................... 160
152-2015 ........................ 133
175-9003......................... 160
152-2016 ........................ 133
175-9004......................... 160
152-2017 ........................ 125
175-9005......................... 160
152-2018 ........................ 125
182-2009........................... 17
152-2019 ................. 143, 147
185-2001......................... 160
152-2020 ................. 143, 147
701-9000....................31, 160
152-2021 ................. 143, 147
701-9001......................... 160
152-2022 ................. 143, 147
701-9002......................... 160
152-2023 ................. 145, 149
701-9003......................... 160
152-2024 ................. 145, 149
701-9004......................... 160
152-2025 ................. 145, 149
701-9005......................... 160
152-2026 ................. 145, 149
704-9000........17, 95, 97, 109,
.................................. 117
151-0003 ... 127, 131, 156, 157
151-0005 ......................... 157
151-2001 ...........................41
151-2002 ..................... 41, 43
151-2009 ......................... 157
151-9000 ......................... 159
151-9001 ......................... 159
151-9002 ......................... 157
151-9003 ......................... 157
151-9004 ......................... 157
151-9005 .......... 135, 136, 137
151-9006 ................. 135, 137
151-9007 ................. 135, 137
151-9011 ................. 135, 137
151-9012 ................. 135, 137
152-1001 .......... 125, 138, 139
152-1002 .......... 125, 140, 141
152-1003 ................. 125, 146
152-1004 .......... 125, 142, 143
152-1005 .......... 125, 144, 145
152-1006 .......... 125, 148, 149
152-1008 .......... 133, 150, 151
152-1009 .......... 129, 152, 153
152-1010 .......... 133, 154, 155
152-2001 ......................... 139
152-2002 ......................... 139
152-2003 ................. 139, 141
152-2004 ................. 139, 141
152-2005 ......................... 139
152-2006 ................. 139, 141
152-2028 ........................ 129
152-2029 ................. 127, 131
152-2035 ................. 151, 153
152-2036 ................. 151, 153
152-2037 ................. 151, 153
152-2038 ................. 151, 153
152-2039 ........................ 129
152-2040 ........................ 133
152-2041 ........................ 125
152-2043 ........................ 129
152-2044 ........................ 155
152-2045 ........................ 155
152-2046 ........................ 125
152-2048 ........................ 135
152-2050 ................. 127, 131
154-9001 ............ 51, 127, 131
154-9002 ............ 51, 127, 131
704-9001......... 17, 51, 95, 97,
............................ 127, 131
704-9002.............. 51, 95, 119
704-9003........................... 63
704-9004............ 17, 109, 131
714-9000......................... 160
721-9000........................... 45
751-9000.............. 45, 51, 129
751-9001.................. 113, 137
785-9001......................... 160
785-9002......................... 160
785-9003......................... 160
785-9004......................... 160
785-9005......................... 160
785-9006......................... 160
785-9007......................... 160
172-1000 ........................ 160
163
OZZIES
INDEX OF PART NAMES
Conveyor
Belt ................. 135, 136, 137
•Flashing ........................ 135
•Lacing Drill Template ...........
............................ 135, 137
•Lacing Kit .............. 135, 137
•Lacing Pin ............. 135, 137
•Lacing Pin Guide .... 135, 137
Belt Adjuster ................... 131
Belt Wipe ........................ 129
Belt Wiper Clamp ............. 129
Belt Wiper Fastening ........ 129
Deflector, Back, Lt ................
........................ 25, 148, 149
•Flashing Base ................ 149
•Mount ........................... 149
•Retainer ........................ 149
•Rib ............................... 149
Deflector, Back, Rt ................
...................... 125, 146, 147
•Flashing Base ................ 147
•Mount ........................... 147
•Retainer ........................ 147
•Rib ............................... 147
Deflector, Front, Lt ................
...................... 125, 144, 145
•Flashing Base ................ 145
•Mount ........................... 145
•Retainer ........................ 145
•Rib ............................... 145
Deflector, Front, Rt ...............
...................... 125, 142, 143
•Flashing Base ................ 143
•Mount ........................... 143
•Retainer ........................ 143
•Rib ............................... 143
Dirt Deflector ....................17
•Mount, Short ....... 39, 42, 43
Pipe ..............................43
Threaded Rod .................43
•Mount, Tall ......... 39, 40, 41,
.............. 143, 145, 147, 149
Pipe ..............................41
Threaded Rod .................41
Frame, Back ..... 125, 140, 141
•Base ............................. 141
•Hold Tab ....................... 141
•Rib, Lt .......................... 141
•Rib, Rt .......................... 141
•Rib. Top ........................ 141
•Slide Rack ..................... 141
Frame, Front .... 125, 138, 139
•Base ............................. 139
164
•Hold Tab ......................
•Rib, Lt ..........................
•Rib, Rt .........................
•Rib. Top .......................
•Slide Rack ....................
139
139
139
139
139
Hinge Tab ...................... 125
Inner Brace Tube ............ 125
Pulley .......127, 131, 156, 157
•Bearing ................. 127, 131
•Bearing, Mount .............. 129
•Bushing ........................ 157
•Coupling Clamp ............. 131
•Group .......................... 157
•Key ................ 127, 131, 157
•Motor Mount, Lt ...................
..................... 133, 150, 151
Alignment Tab ...... 151, 153
Base ........................... 151
Mount ......................... 151
Rib ............................. 151
•Motor Mount, Rt ..................
..................... 129, 152, 153
Base ........................... 153
Mount ......................... 153
Rib ............................. 153
•Motor, Type D ........ 127, 131
•Motor, Type E ........ 127, 131
•Roller ........................... 157
•Shaft ........................... 157
•Shaft Coupling .............. 127
•Wipe ..................... 129, 133
•Wipe Mount Tab ............ 129
•Wiper Mount ... 133, 154, 155
Pipe ............................ 155
Plate ........................... 155
Roller .............. 129, 158, 159
•Bearing ........................ 159
•Pin ............................... 129
Shift Assembly, Lt .. 31, 44, 45
•Frame ................. 45, 46, 47
Coupling Plate, Front ...... 47
Coupling Plate, Rear ....... 47
Frame Plate, Front .......... 47
Frame Plate, Rear ........... 47
Mount Plate ................... 47
Roller Mounting Plate, Rear
.................................... 47
Wipe ............................. 47
Wipe Mount, Inner .......... 47
Wipe Mount, Outer ......... 47
•Guide Roller .................... 45
•Pin Holder..... 45, 48, 49, 129
Hold Plate...................... 49
Sleeve .......................... 49
•Roller ............................. 45
•Roller Pin ........................ 45
Shift Assembly, Rt .. 31, 50, 51
•4 Pcs Coupler .................. 51
•4 Pcs Coupler with Zerk .... 51
•Bearing........................... 51
•Drive Shaft ..................... 51
•Frame ................. 51, 52, 53
Frame Mount .................. 53
Motor Mount .................. 53
Roller Mount .................. 53
Side Mount .................... 53
Wear Plate ..................... 53
Wear Plate Holder ........... 53
Wear Plate Mount ........... 53
Wipe ............................. 53
Wiper Clamp .................. 53
•Key ................................ 51
•Motor, Type D ................. 51
•Motor, Type E .................. 51
•Pin Holder ....................... 51
•Roller ............................. 51
•Sprocket ......................... 51
•Sprocket Chain ................ 51
Shift Stop ....................... 125
View 1 .................... 124, 125
View 2 .................... 126, 127
View 3 .................... 128, 129
View 4 .................... 130, 131
View 5 .................... 132, 133
View 6 .................... 134, 135
Wiper ............................. 133
Wiper Clamping Plate ....... 133
Wiper Fastening Plate ...... 133
Electronics
Control Box Dash Plate ..... 160
Control Box to SD1 Harness
..................................... 160
Eti Joystick Rocker Pot ..... 160
MC24 Micro Controller ...... 160
Ram Mount ..................... 160
Elevator .....................92, 93
Belt Wipe .............. 31, 62, 63
•Bushing Housing ... 63, 64, 65
Mount Plate.................... 65
Pipe .............................. 65
•Frame ................. 63, 66, 67
Gusset Short .................. 67
Gusset, Long .................. 67
Gusset, Medium ............. 67
Hinge Rod ...................... 67
INDEX OF PART NAMES
OZZIES
Retainer Plate .................67
Shaft Retention Plate .......67
•Retainer Plate ..................63
•Shaft Bushing ..................63
•Wipe ...............................63
Chain ........ 93, 95, 97, 98, 99
•11/2”Producing w/ Flights...99
•11/2”Producing w/o Flights
.................................... 101
•3/8”Producing w/ Flights ....99
•3/8”Producing w/o Flights . 101
•Belt Adjuster .... 93, 108, 109
Bearing ........................ 109
Frame........... 109, 110, 111
Tube ......................... 111
Roller .......................... 109
Telescoper ................... 109
Wiper .......................... 109
•Belt Drive
Belt ................ 93, 112, 113
Lacing Drill Template93, 113
Lacing Kit ............... 93, 113
Lacing Pin .............. 93, 113
Lacing Pin Clip ...... 113, 137
Lacing Pin Guide ..... 93, 113
•Chains without Flights ..........
............................ 100, 101
•Elevator Flight ............... 101
Coupler Housing with Grease
Fitting ........................ 95, 97
Lower Elevator Motor Shield
Assembly .................... 17, 97
Lower Elevator Motor Top
Cover Assembly ........... 17, 97
Lower Head Pulley, Lt, Cover
........................... 31, 58, 59
•Cover Pipe .......................59
•Guard Plate .....................59
Lower Head Pulley, Rt, Cover
........................... 31, 60, 61
•Cover Pipe .......................61
•Guard Plate .....................61
Lower Head Pulley, Wipe........
........................... 31, 68, 69
•Blade ..............................69
•Frame ................. 69, 70, 71
Frame Mount ..................71
Gusset ...........................71
Support .........................71
Wipe Mount ....................71
Lower Motor
•Mount, Bottom ..... 73, 86, 87
INDEX OF PART NAMES
Base ............................. 87
Front ............................ 87
Seat Block ..................... 87
Lower Pulley ......... 93, 95, 97,
.................. 98, 99, 106, 107
•Belt Adjuster ..... 93, 108, 109
Bearing ....................... 109
Frame ........... 109, 110, 111
Tube ......................... 111
Roller .......................... 109
telescoper ................... 109
Wiper.......................... 109
•Belt Drive
Belt ................ 93, 112, 113
Lacing Drill Template93, 113
Lacing Kit ............... 93, 113
Lacing Pin............... 93, 113
Lacing Pin Clip ...... 113, 137
Lacing Pin Guide...... 93, 113
•Coupler Seal ................... 97
•Coupler Sprocket ............. 97
•End Cap ....................... 107
•Groove ......................... 107
•Motor .................. 93, 96, 97
4 Pcs Coupler ................. 97
Bearing ......................... 97
Coupler Chain ................ 97
Coupler with Zerk ...... 97, 99
Guard Back.................... 97
Mount ........................... 97
Seat Block ..................... 97
Type D Motor ................. 97
Type E Motor ................. 97
•Pipe ............................. 107
•Roller Bearing Key ........... 97
•Shaft ........................... 107
Rock Guard, Lt ....... 31, 36, 37
•End Rib .......................... 37
•Flashing ......................... 31
•Flashing Retainer Plate ..... 31
•Flush Plate, Inside ........... 37
•Flush Plate, Outside ......... 37
•Rib Plate......................... 37
•Top Plate ........................ 37
Rock Guard, Rt ...... 31, 38, 39
•End Rib .......................... 39
•Flashing ......................... 31
•Mount, Short ........ 39, 42, 43
Pipe .............................. 43
Threaded Rod ................ 43
•Mount, Tall ......... 39, 40, 41,
..............143, 145, 147, 149
Pipe .............................. 41
Threaded Rod ................ 41
•Rib Plate ......................... 39
•Top Plate ........................ 39
Scoop, Lt ............... 73, 76, 77
•Backing .......................... 77
•Gusset ............................ 77
•Main Plate ....................... 77
•Rib Spacer ...................... 73
•Side ............................... 77
•Top Cover ....................... 77
•Wear Plate ...................... 33
Scoop, Rt .............. 73, 74, 75
•Backing .......................... 75
•Gusset ............................ 75
•Main Plate ....................... 75
•Rib Spacer ...................... 73
•Side ............................... 75
•Top Cover ....................... 75
•Wear Plate ...................... 33
Side Plate, Lt .................... 33
Side Plate, Rt .................... 33
Slack Pulley ....... 99, 102, 103
•Roller ........................... 103
•Shaft ............................ 103
Spill Plate .............. 33, 56, 57
•Hinge Pipe ...................... 57
•Hinge Rod ....................... 57
•Spill Plate ....................... 57
•Tab ................................ 57
Upper Motor Mount ...............
...................... 73, 80, 81, 95
•Back............................... 81
•Bolt Plate ........................ 81
•Gusset ............................ 81
•Mount............................. 81
Upper Pulley ......... 93, 95, 97,
................... 98, 99, 104, 105
•Bushing ........................ 105
•Motor .................. 93, 94, 95
4 Pcs Coupler ................. 95
Bearing ......................... 95
Coupler Chain ................ 95
Coupler with Zerk ........... 95
Idler Spacer ................... 95
Rubber Seal ................... 95
Sprocket ........................ 95
Type D Motor ................. 95
Type E Motor.................. 95
•Pulley Flange ................. 105
•Roller ........................... 105
•Roller Bearing Key ......... 105
•Weld Hub ...................... 105
Upper Pulley
•Shaft ............................ 105
Elevator Chain
Motor, Lower, Cover .... 26, 27
•Cover Tube ..................... 27
165
•Deflecting Plate ................27
•End Plate ........................27
•Mount Plate .....................27
Motor, Lower, Cover Mount ....
................................. 28, 29
•Cover Plate......................29
•Front Plate ......................29
•Seat Plate .......................29
Slack Adjuster, Lt .. 17, 24, 25
•Bearing ...........................17
•Bearing Mount Plate .........25
•Bracket ...........................25
•Grease Tube, Inner ..........25
•Grease Tube, Outer ..........25
•Gusset ............................25
•Mounting Plate .................25
•Rod End ..........................25
•Spacing Plate ...................25
•Spring ............................25
•Spring Seat, Lower ...........25
•Spring Seat, Upper ...........25
•Threaded Rod ..................25
Slack Adjuster, Rt .. 17, 20, 21
•Bearing ...........................17
•Bearing Mount Plate .........21
•Bracket ...........................21
•Grease Tube, Inner ..........21
•Gusset ............................21
•Mount Plate .....................21
•Rod End ..........................21
•Spacing Plate ...................21
•Spring ............................21
•Spring Seat, Lower ...........21
•Spring Seat, Upper ...........21
•Threaded Rod ..................21
•Tube, Outer .....................21
Final Assembly .......... 16, 17
Flashing
10" Wide Flashing per Foot ....
..................................... 160
4" Wide Flashing per Foot ......
..................................... 160
6" Wide Bulldog Flashing per
Foot ............................... 160
6" Wide Flashing per Foot ......
..................................... 160
8" Wide Bulldog Flashing per
Foot ............................... 160
•Fins ............................... 23
•Support Frame ..... 73, 82, 83
Bottom ......................... 83
Bottom Support Skid Pocket
......................... 83, 84, 85
Base ........................... 85
Front .......................... 85
Side ........................... 85
Front Support ................ 83
Gusset, Back ................. 83
Gusset, Front ................. 83
Rib ............................... 83
Support ......................... 83
Top Support .................. 83
Hitch Plate ............ 73, 78, 79
•Back Plate ...................... 79
•Main Plate ...................... 79
•Rib ................................ 79
•Support, Top ................... 79
Hitch Plate, Support Bottom 79
Lower Elevator Motor Mount
........................... 73, 86, 87
•Base .............................. 87
•Front.............................. 87
•Seat Block ...................... 87
Lower Elevator Motor Shield
Assembly .................... 17, 97
Lower Elevator Motor Top
Cover Assembly ........... 17, 97
Motor, Lower, Cover ..... 26, 27
•Cover Tube ..................... 27
•Deflecting Plate ............... 27
•End Plate ........................ 27
•Mount Plate .................... 27
Motor, Lower, Cover Mount ....
................................. 28, 29
•Cover Plate ..................... 29
•Front Plate ...................... 29
•Seat Plate ....................... 29
Plate, Back ....................... 73
Quick Connect ....... 17, 18, 19
•Back Plate ...................... 19
•Hitch Bolt Plate ............... 19
•Hook .............................. 19
•Hook Doubler Plate .......... 19
•Rib ................................ 19
Back Rib ...........................73
Scoop, Lt .............. 73, 76, 77
•Backing .......................... 77
•Gusset ........................... 77
•Main Plate ...................... 77
•Rib Spacer ...................... 73
•Side ............................... 77
•Top Cover ....................... 77
Cutting Blade .............. 17, 22
•Blade ..............................23
Scoop, Rt .............. 73, 74, 75
•Backing .......................... 75
8" Wide Flashing per Foot . 160
Frame ............ 16, 17, 72, 73
Back Gusset ......................73
166
OZZIES
•Gusset ............................ 75
•Main Plate ....................... 75
•Rib Spacer ...................... 73
•Side ............................... 75
•Top Cover ....................... 75
Side, Lt ............................ 73
Side, Rt ............................ 73
Ski, Lt .............................. 73
•Wear Plate ...................... 73
Ski, Rt ............................. 73
•Wear Plate ...................... 73
Skid Bar ........................... 73
Skid Mount ....................... 73
Slack Adjuster, Lt ... 17, 24, 25
•Bearing........................... 17
•Bearing Mount Plate ......... 25
•Bracket ........................... 25
•Grease Tube, Inner .......... 25
•Grease Tube, Outer .......... 25
•Gusset ............................ 25
•Mounting Plate ................ 25
•Rod End .......................... 25
•Spacing Plate .................. 25
•Spring ............................ 25
•Spring Seat, Lower .......... 25
•Spring Seat, Upper........... 25
•Threaded Rod .................. 25
Slack Adjuster, Rt ... 17, 20, 21
•Bearing........................... 17
•Bearing Mount Plate ......... 21
•Bracket ........................... 21
•Gusset ............................ 21
•Mount Plate ..................... 21
•Rod End .......................... 21
•Spacing Plate .................. 21
•Spring ............................ 21
•Spring Seat, Lower .......... 21
•Spring Seat, Upper........... 21
•Spring Tube, Inner ........... 21
•Spring Tube, Outer .......... 21
•Threaded Rod .................. 21
Support ............................ 73
Upper Elevator Motor Mount
...................... 73, 80, 81, 95
•Back............................... 81
•Bolt Plate ........................ 81
•Gusset ............................ 81
•Mount............................. 81
Valve Stack ........... 73, 88, 89
•Bank Seat ....................... 89
•Bolt Plate ........................ 91
•Cover .................. 89, 90, 91
Enclosure....................... 91
Handle .......................... 91
top ............................... 91
INDEX OF PART NAMES
OZZIES
•Mounting .........................89
•Mounting Channel ............89
•Seat Mount ......................89
•Seat Mounting .................89
•Support ..........................89
•Valve Bank ......................89
Frame Attachments
Bottom Support Skid .............
........................... 33, 34, 35
•Bottom Skid Plate.............35
•Pocket ................ 83, 84, 85
Base ..............................85
Front .............................85
Side ..............................85
•Rib Plate .........................35
•Top Plate.........................35
Conveyor Shift Assembly, Lt
........................... 31, 44, 45
•Frame ................. 45, 46, 47
Coupling Plate, Front .......47
Coupling Plate, Rear ........47
Frame Plate, Front ..........47
Frame Plate, Rear ...........47
Mount Plate ....................47
Roller Mounting Plate, Rear
....................................47
Wipe .............................47
Wipe Mount, Inner ..........47
Wipe Mount, Outer ..........47
•Guide Roller ....................45
•Pin Holder .... 45, 48, 49, 129
Hold Plate ......................49
Sleeve ...........................49
•Roller..............................45
•Roller Pin ........................45
Conveyor Shift Assembly, Rt
........................... 31, 50, 51
•4 Pcs Coupler...................51
•Bearing ...........................51
•Drive Shaft ......................51
•Frame ................. 51, 52, 53
Frame Mount ..................53
Motor Mount ...................53
Roller Mount ...................53
Side Mount .....................53
Wear Plate .....................53
Wear Plate Holder ...........53
Wear Plate Mount ............53
Wipe .............................53
Wiper Clamp ..................53
•Key ................................51
•Motor, Type D ..................51
•Motor, Type E ..................51
•Pin Holder .......................51
•Roller..............................51
•Sprocket .........................51
•Sprocket Chain ................51
INDEX OF PART NAMES
Conveyor Shift Assembly, Rt
•4 Pcs Coupler with Zerk .... 51
Deflector Stop .................. 31
Elevator Belt Wipe .. 31, 62, 63
•Bushing Housing... 63, 64, 65
Mount Plate ................... 65
Pipe .............................. 65
•Frame ................. 63, 66, 67
Gusset, Long ................. 67
Gusset, Medium ............. 67
Gusset, Short ................ 67
Hinge Rod ..................... 67
Retainer Plate ................ 67
Shaft Retention Plate ...... 67
•Retainer Plate ................. 63
•Shaft Bushing ................. 63
•Wipe .............................. 63
Elevator Rock Guard, Lt .........
........................... 31, 36, 37
•End Rib .......................... 37
•Flashing ......................... 31
•Rib Plate......................... 37
•Top Plate ........................ 37
Elevator Rock Guard, Rt .........
........................... 31, 38, 39
•End Rib .......................... 39
•Flashing ......................... 31
•Mount, Short ........ 39, 42, 43
Pipe .............................. 43
Threaded Rod ................ 43
•Mount, Tall ......... 39, 40, 41,
..............143, 145, 147, 149
Pipe .............................. 41
Threaded Rod ................ 41
•Rib Plate......................... 39
•Top Plate ........................ 39
Elevator Scoop, Lt
•Wear Plate ...................... 33
Elevator Scoop, Rt
•Wear Plate ...................... 33
Elevator Side Plate, Lt........ 33
Elevator Side Plate, Rt ....... 33
Elevator Spill Plate . 33, 56, 57
•Hinge Pipe ...................... 57
•Hinge Rod....................... 57
•Spill Plate ....................... 57
•Tab ................................ 57
•Master Hitch Cylinder ..... 160
Lower Head Pulley, Lt, Cover
............................ 31, 58, 59
•Cover Pipe ...................... 59
•Guard Plate ..................... 59
Lower Head Pulley, Rt, Cover
............................ 31, 60, 61
•Cover Pipe ...................... 61
•Guard Plate ..................... 61
Lower Head Pulley, Wipe ... 31,
68, 69
•Blade ............................. 69
•Frame ................. 69, 70, 71
Frame Mount .................. 71
Gusset .......................... 71
Support ......................... 71
Wipe Mount ................... 71
Rubber Retention Plate ....... 31
Shaft
•Bearing......................... 117
Vibrator................... 114, 115
•Flex Coupling ................ 117
•Frame ................... 115, 119
Bearing ....................... 119
Bearing Mount .............. 119
Cover Plate .................. 119
Gusset ........................ 119
Square Tube, Long ........ 119
Square Tube, Short ....... 119
•Frame Mount ................. 119
•Isolator ........................ 115
•Motor Bracket ........ 117, 119,
............................ 120, 121
Motor Mount ................ 121
Mount ......................... 121
Side ............................ 121
•Motor Coupler ............... 117
•Motor, Type E ................ 117
•Roller ........................... 119
•Shaft ..............115, 116, 117
Key ............................. 117
•Shaft Coupling ............... 117
•Weighted Shaft ...... 117, 119,
122, 123
Donut.......................... 123
Pipe ............................ 123
Shaft ........................... 123
Vibrator Isolator Bracket .......
............................ 33, 54, 55
•Isolator .......................... 55
•Mount Plate ..................... 55
•Square Tube ................... 55
Vibrator Roller Rubber ........ 31
High Pressure Filter, 90GPM,
20µ ............................... 160
Vibrator Wipe Plate ............ 31
Kat Master Hitch ............. 160
View 2 ............................. 33
View 1 ....................... 31, 32
167
OZZIES
Gauge Mounting Plate
Gauge Mount.....................89
Grease Fittings
45° Head
•1/8”NPT .............. 51, 95, 119
65° Head
•1/8”NPT ...........................63
90° Head
•1/8”NPT . 17, 95, 97, 109, 117
Straight Head
•1/4”28 UNC ....... 17, 109, 131
•1/8”NPT .......... 17, 51, 95, 97
•1/8”NPT ................ 127, 131
Hex Bolts
- 1/2” ⌀
•1” Length, 13 UNC .. 81, 109,
131
•11/2” Length, 13 UNC ...........
..... 17, 33, 97, 115, 119, 129
•13/4” Length, 13 UNC .. 31, 47
•21/4” Length, 13 UNC ...... 133
•23/4” Length, 13 UNC .. 95, 97
•31/4” Length, 13 UNC ...... 119
•33/4” Length, 13 UNC ...... 119
- /2” ⌀ Counter Sunk
•11/2” Length, 13 UNC .. 17, 31
•11/2” Length, 13 UNC ..........
............................ 125, 135
•2” Length, 13 UNC ..... 95, 97
1
- 1/2” ⌀ Hex Socket
•1” Length, 13 UNC ......... 105
- 1/4” ⌀
•1/2” Length, 20 UNC ..........91
•21/2” Length, 20 UNC ........73
•5/8” Length, 20 UNC .. 45, 129
- 3/4” ⌀
• 2” Length, 10 UNC ...........17
- /8” ⌀
•1” Length, 16 UNC 17, 31, 33
•1” Length, 16 UNC .... 69, 97
•11/2” Length, 16 UNC ...........
.......................... 31, 45, 53
•11/2” Length, 16 UNC ..... 133
•11/4” Length, 16 UNC ...........
......................... 53, 63, 129
•11/8” Length, 16 UNC ..... 125
•3/4” Length, 16 UNC .... 31, 89
3
- /8” ⌀ Counter Sunk
•11/4” Length, 16 UNC ........53
3
- 3/8” ⌀ Hex Set Screw
•5/8” Length, 13 UNC ........ 157
- 3/8” ⌀ Hex Socket
•11/4” Length, 16 UNC ...........
............................ 127, 131
168
- 7/16” ⌀
•13/4” Length, 14 UNC ..... 117
Ttp Heat Exchanger ......... 160
/2” ⌀, 13 UNC ........ 33, 47, 83
Valve Stack
•Coil .........................89, 160
•Presure Gauge ............... 160
/2” ⌀, 13 UNC ......................
.................. 95, 97, 115, 119
Vickers Solenoid Valve ..... 160
Hex Nuts
1
1
/2” ⌀, 13 UNC ......................
...............125, 129, 133, 135
1
/4” ⌀, 20 UNC ................... 91
1
1” ⌀, 8 UNC ................. 21, 25
11/4” ⌀, 12 UNC ................. 45
/4” ⌀, 10 UNC ................... 79
3
/8” ⌀, 16 UNC ... 37, 39, 41, 43
3
/8” ⌀, 16 UNC .. 45, 53, 63, 71
3
3
/8” ⌀, 16 UNC ......................
...............129, 133, 139, 141
/8” ⌀, 18 UNC ........ 21, 25, 45
5
/16” ⌀, 14 UNC ............... 117
7
Hydraulic
/2” Stucci Female Quick
Coupling ........................ 160
1
/2” Stucci Male Quick
Coupling ........................ 160
1
1” Stucci Female Quick
Coupling ........................ 160
1” Stucci Male Quick Coupling
.................................... 160
11/4” Stucci Female Quick
Coupling ........................ 160
11/4” Stucci Male Quick
Coupling ........................ 160
Hydraulics
24 Volt Coil W/ Wire Leads 160
4 Way 3 Position Cartridge
Valve ............................. 160
Cartridge Valve Body ....... 160
Daman Header Manifold 90°,
Case Drain ..................... 160
Fan Motor Combo ............ 160
High Pressure Filter, 90GPM,
20µ ............................... 160
Hydraforce Iron Body ...... 160
Master Hitch Cylinder....... 160
Radiator Mount ............... 160
Rebuilt Valve Stack Cva-8572
.................................... 160
Shuttle Valve .................. 160
Side Plug Bulkhead .......... 160
Steel Hydraulic Block ....... 160
Vickers Deutsch 24vdc Coil160
Loader
Controls
•Control Box Dash Plate ... 160
•Control Box to SD1 Harness
................................... 160
•Eti Joystick Rocker Pot .... 160
•MC24 Micro Controller .... 160
•Ram Mount ................... 160
Hitch Plate ............. 73, 78, 79
•Back Plate ....................... 79
•Main Plate ....................... 79
•Rib ................................. 79
•Support, Bottom .............. 79
•Support, Top ................... 79
Hydraulics
•1/2” Stucci Female Quick
Coupling ....................... 160
•1/2” Stucci Male Quick
Coupling ....................... 160
•1” Stucci Female Quick
Coupling ....................... 160
•1” Stucci Male Quick
Coupling ....................... 160
•11/4” Stucci Female Quick
Coupling ....................... 160
•11/4” Stucci Male Quick
Coupling ....................... 160
•High Pressure Filter, 90GPM,
20µ .............................. 160
•Kat Master Hitch
Master Hitch Cylinder .... 160
•Kat Master Hitch ............ 160
•Radiator Mount .............. 160
•Shuttle Valve................. 160
•Side Plug Bulkhead ........ 160
•Steel Hydraulic Block ...... 160
Quick Connect ........ 17, 18, 19
•Back Plate ....................... 19
•Hitch Bolt Plate ................ 19
•Hook .............................. 19
•Hook Doubler Plate .......... 19
•Rib ................................. 19
Pins
Extended Prongs
•1/4” x 11/2” ...................... 95
•3/16” x 2”......................... 57
Vibrator .................114, 115
Flex Coupling .................. 117
Frame ..................... 115, 119
INDEX OF PART NAMES
OZZIES
•Bearing ......................... 119
•Bearing Mount ............... 119
•Cover Plate.................... 119
•Gusset .......................... 119
•Square Tube, Long ......... 119
•Square Tube, Short ........ 119
Frame Mount ................... 119
Isolator .......................... 115
Isolator Bracket ..... 33, 54, 55
•Isolator ...........................55
•Mount Plate .....................55
•Square Tube ....................55
Motor Bracket .......................
............... 117, 119, 120, 121
•Motor Mount .................. 121
•Mount ........................... 121
•Side ............................. 121
Motor Coupler ................. 117
Motor, Type E .................. 117
INDEX OF PART NAMES
Roller ............................ 119
•5/8” ................................ 57
Roller Rubber ................... 31
Flat Washers, Narrow
•1/2” .......... 17, 31, 33, 47, 95
•1/2” ................... 81, 97, 119
•1/2” ....... 125, 129, 133, 135
•1/4” .........................45, 129
•11/2” .............................. 95
•11/4” ............................... 45
•3/8” ....................... 125, 133
•7/16” ............................. 117
Roller Wipe Plate ............... 31
Rubber Retention Plate ...... 31
Shaft ............... 115, 116, 117
•Bearing ........................ 117
•Key .............................. 117
Shaft Coupling ................ 117
Weighted Shaft 117, 119, 122,
123
•Donut .......................... 123
•Pipe ............................. 123
•Shaft ........................... 123
Washers
ASTM Washers
•1/2” ....................... 119, 131
•1/4” ................................ 91
•1” ............................. 21, 25
•3/8” .............................. 129
Flat Washers, Regular
•1/2” .........................33, 115
•3/8” .... 17, 31, 33, 45, 53, 69
•3/8” .......................... 89, 97
•5/8” ................................ 45
Lock Washers
•1/2” .......................... 95, 97
•3/4” ................................ 17
169
OZZIES
NOTES
MINI PADDER PARTS MANUAL
AUGUST 2014 – REV. A4
PHONE:(480) 585-9400
FAX:(480) 585-7977
Opening its doors in the 1980s, Ozzie’s delivered the first all-in-one padding machine to
the world. Since then we have established ourselves as the premier source for pipeline
padding equipment large and small, and continue to push the envelope in pipeline
OZZIES
equipment engineering.
Contact us today to see how we can help you.
Corporate Office
ESI Energy Services Inc.
Robert Dunstan - President & CEO
Suite 500
727 - 7th Ave SW
Calgary, AB T2P 0Z5
Canada
Direct:
+1 403.205.7188
Mobile:
+1 403.618.5983
Email:
robert.dunstan@energyservicesinc.com
T:+1 403.262.9344
F:+1 403.571.5191
Canada
Ozzie’s Pipeline Padder of Canada
A division of ESI Pipeline Servies Ltd.
Gabriel Pupaza – Operations Manager
Direct:
+1 780.980.2781
7506 - 43 street
Leduc, AB T9E 7E8
Canada
Mobile:
+1 780.913.5056
OZZIES
Email:
gabriel.pupaza@toranpower.com
T:+1 780.980.8000
F:+1 780.980.8001
United States
Ozzie’s Pipeline Padder, Inc.
7102 West Sherman Street
Phoenix, AZ 85043
USA
T:+1 480.585.9400
F:+1 480.585.7977
Chris Argue – Operations Manager
OZZIES
Direct:
+1 623.889.7941
Mobile:
+1 623.738.1081
Email:
chris.argue@ozzies.com
Scott Jeter – Sales
Direct:
+1 623.889.7945
Mobile:
+1 281.702.6903
Email:
scott.jeter@ozzies.com
MINI PADDER PARTS MANUAL
AUGUST 2014 – REV. A4
Scan to visit Ozzies.com
PHONE:(480) 585-9400
FAX:(480) 585-7977

Mini Padder Part Manual

Transcription

Similar documents

JD644-A LOADER