SaoCal Net

Edited by Foxit PDF Editor
Copyright (c) by Foxit Software Company, 2004 - 2007
For Evaluation Only.
OPERATING MANUAL
RS-485 to 10BaseT Ethernet LAN Converter
SaoCal Net
■ łączność przez sieć Ethernet
■ nadzór i kontrola z poziomu przeglądarki inetrnetowej
■ współpraca z programem SaoCal Soft
Uwagi!!
● Przed rozpoczęciem montażu i obsługi uważnie przeczytać niniejszą instrukcję.
● Obsługę i serwis urządzenia należy wykonywać zgodnie z opisem w niniejszej instrukcji,
by uniknąć zniszczeń lub szkód.
● Nie wolno uruchamiać urządzenia na podstawie przypuszczeń.
● Proszę mieć zawsze pod ręką instrukcję montażu i obsługi.
● Wątpliwości związane z instrukcją należy koniecznie wyjaśnić z działem technicznym producenta.
● Niewłaściwa instalacja przyrządu może prowadzić do zagrożenia życia lub zdrowia użytkowników.
HUSTY ul. Rzepakowa 5e, 31-989 Kraków
tel. 012-645-03-04, tel. 012-645-03-33, e-mail: info@husty.pl www.husty.pl
Omschrijving piktogrammen
Edited by Foxit PDF Editor
Copyright (c) by Foxit Software Company, 2004 - 2007
For Evaluation Only.
Attention! Danger! Caution! -Warning or important note!
Risk of electric sock or safety.
Handle and use note.
Manufacturer notes
The manufacturer reserves the right to improve and update the technical details in connection
with continuously upgrading device functionality.
PREFACE
This user manual ivolves the instalation and operation of SaoCal Net interface to connect SAOCAL controler to the computer using software SaoCal Soft and/or by the own www page to
any gear (p.e: handy or smart phone, tablet etc) using WiFi or 3g net.
SaoCal Net/122k10/HUSTY/INSTRUKCJA
The unit is manufactured in complies with the respective EU regulations.
Converter can not be install and use in a hazardous areas.
DELIVERY NOTES
Converter is delivered as ready to use as blow:
● Converter SaoCal Net.
● USB cable.
● LAN RJ45 cross cable (red plugs) for start programing.
● LAN RJ45 (green plugs) green cable for normal ETHERNET operation.
● Power adapter 230VAC/12VAC.
● Operating manual.
HUSTY sp.J.
ul. Rzepakowa 5e, 31-989 Kraków tel. +48-12-645-03-04, faks: +48-12-645-03-33,
e-mail:info@husty.pl www.husty.pl
All righst reserved. No part of this manual may be duplicated and/or made public throught the Internet, by mans of printing, photocoping,
microfilm or in any other without prior written permision from HUSTY.
2
TABLE OF CONTENT
TABLE OF CONTENT
PAGE
SYMBOLS AND GENERAL REMARKS..............................................................................2
TABLE OF CONTENT..........................................................................................................3
1.PURPOSE.........................................................................................................................4
2.INSTALLATION................................................................................................................5
2.1. MECHANICAL INSTALATION .................................................................................5
2.2. Electrical installation.................................................................................5
2.2.1 Power supply and RS-485 connection..............................................6
2.2.2 LAN network connection......................................................................6
3.SETTINGS and CONFIGURATION.................................................................................7
3.1. First configuration.........................................................................................7
3.2. Changing the configuration........................................................................11
3.3. Restoring default settings.........................................................................11
4.LED DIODES....................................................................................................................13
5.TECHNICAL DATA...........................................................................................................14
6.MANUFACTURER............................................................................................................14
SaoCal Net/122k10/HUSTY/INSTRUKCJA
7.NOTES..............................................................................................................................15
3
1. PURPOSE
1. Purpose
Typical application
Converter SaoCal Net allows data transfer between master
system (PC computer, PLC controller) which works in LAN
network with TCP/IP communication protocol and SaoCal
controller devices with RJ-9 serial port. Every client can
connect using computer software SaoSoft Terminal or SaoSoft Service with SaoCal controller using IP address and
port number set during configuration of SaoCal Net converter. In “Transparent” mode – converter receives character
string from LAN network and sends it to RS-485 network
and vice versa.
Converter is dedicated to work in industrial or laboratory
systems, in electric or control cabinets or inside control rooms as standalone device or mounted on DIN rail (version
with locking clip).
SaoCal Net/122k10/HUSTY/INSTRUKCJA
Connection to other part of
local networki or Internet
4
2. INSTALLATION
2. 1. Mechanical instalation
Version with locking clip allows to install converter on DIN
rail.
Converter installed on DIN rail
2. 2. Electrical instalation
not used
Converter has got two sockets, one for connection to
LAN network and second one is six positions screw terminal to connect to RS-485 bus and to power supply.
That screw terminal is preinstalled and connected
to transformer and with RJ-9 plug ready for connection to
controller.
Plug RJ45
pin no.
1
Description
+12V DC /12 AC
Additional informations
Power supply
2
3
4
5
6
A (+)
A (+)
B (-)
B (-)
GND DC /12 AC
"GND" and port RS-485
SaoCal Net/122k10/HUSTY/INSTRUKCJA
pin no.
-
Ethernet
Description
Additional informations
Ethernet
Plug RJ45
RS-485 and power supply
Plug RS-485
5
2. INSTALLATION
2. 2. 1. Power supply
and RS-485 connection
SaoCal should be connected 12 V AC/DC e.g. voltage from transformer 230 VAC / 12 VAC.
Podłączenie wtyczki
zasilanie i RS-485
SaoCal Net/122k10/HUSTY/INSTRUKCJA
2. 2. 2. LAN network connection
6
There are tow cables in the converter kit: UTP twisted pair cable (green) and cross-over (black with red boots). Normally in LAN network UTP cable (green) should be
used. Cross-over cable should be used to connect converter with computer directly.
3. SETTINGS and CONFIGURATION
3. 1. First configuration
A PC computer has to be used to make proper configuration. It should be done through LAN network using standard
Internet Web browser.
Normally LAN network configuration causes that converter with default settings is not “visible” in network.
During first configuration SaoCal Net converter should be first connected to PC computer using cross-over cable (black with red boots).
Computer should have network configuration setup
to dynamic host configuration.
(Moje miejsce sieciowe ►Właściwości ► Połączenie sieciowe ► Ogólne ► Właściwości ► Ogólne ► Protokół
internetowy (TCP/IP) ► Właściwości ► Uzyskaj adres IP
automatycznie).
For configuration properties it is no need to connect
RS-485 bus but power supply has
SaoCal Net/122k10/HUSTY/INSTRUKCJA
Converter direct connection to PC computer
7
3. SETTINGS and CONFIGURATION
Using a Web Browser in address bar converter IP address should be typed in: 1.0.0.1.
After that a following configuration screen appears:
SaoCal Net/122k10/HUSTY/INSTRUKCJA
Then LOGIN should be pressed, following screen appears:
User is admin and default password is ‘12345’,
8
3. SETTINGS and CONFIGURATION
after that following screen appears:
Default password is ‘12345’ and it is necessary to be entered to accept any changes.
In “RS-485” tab are serial port settings and the same password have to be used. In “password” tab user can change password and set LED diodes TxD and RxD on and off for test.
9
SaoCal Net/122k10/HUSTY/INSTRUKCJA
There are four tabs in menu: “SaoCal”, “ethernet”, “rs485” and “password”.
In “ethernet” tab are network settings and 5 characters password.
Default settings for LAN network are as follow:
IP address: 1.0.0.1
Port: 502
Subnet mask: 255.255.255.0
Default gateway: 1.0.0.1
Server DHCP: ON
Connection timeout: 60 s
3. SETTINGS and CONFIGURATION
During first configuration following parameters should be filled up: IP address, subnet
mask, default gateway in accord with network where it will be use. DHCP server should be turned off. In default settings it is turned on for communication between converter and computer
during first configuration. Connection Timeout is maximal time without exchange of data with
master system and have to be set properly according to user application.
Acceding the Connection Timeout causes client connection close.
SaoCal Net/122k10/HUSTY/INSTRUKCJA
After that SaoCal Net has to be
- reconnected using UTP (green) cable to HUB
- connect to SaoCal controller using prepared cable with RJ-9 plug, as presented at the page 4.
- connnect computer to the net
- turn on program SaoCal Soft Terminal or SaoCal Soft Service
- take from menu "Datas transmission" – ethernet web
- take new IP address SaoCal Net (preprogramed elier in section Ethernet data transmission)
That new IP address has to be used while connection between computer and SaoCal need to
be established.
10
3. SETTINGS and CONFIGURATION
3.2. Changing the configura-
Any change of configuration can be done using PC computer in similar way like for first configuration. But there is no
need to connect converter directly to the computer again. If
converter is present in LAN network then user is able to
start configuration window with Web
Browser using converter IP address.
3.3. Restoring default settings
Execution 1
In some service cases a need to set up default settings may
occur. Especially user has to do it in case when converter network parameters are forgotten. To make parameters
reset to default first the converter housing case has to be
removed using 4 screws on the bottom.
Case remove
Next pins 4 and 5 have to connected with a jumper
(picture below) followed by power on.
TxD and RxD diodes should start blink. Then jumper on
pins 4 and 5 should be removed and power should be turned off. Default settings are restored.
Short-circuit of other pins or components may permanently destroy converter.
Execution 2
small reset
hole in housing
1.
2.
3.
4.
To make parameters reset to default:
Remove green power plug from the converter.
Using thin stick press and hold RESET switch
inside housing.
Using grenn power plug switch on power supply for
converter SaoCal Net.
Release RESET switch - converter are restored to
default setting (see page 9).
SaoCal Net/122k10/HUSTY/INSTRUKCJA
“Reset” jumper on pines 4 and 5,
two peripheral pins on left side.
“Reset” contact inside housing.
11
4. LED DIODES
Converter has got 5 LED diodes allowing to monitor the converter status:
sygnalling power supply
sygnalling data recive to RS 485
sygnalling data transmission to RS 485
sygnalling acive connection to LAN network
SaoCal Net/122k10/HUSTY/INSTRUKCJA
sygnalling data transmission thruogh LAN port
12
5. TECHNICAL DATA
POWER SUPPLY
CONV485E -1 (24 V DC/AC):
LED diodes:
POWER SUPPLY
Work temperature / Store temperature:
Humidity:
MECHANICAL DIMENSIONS
Dimension (length x width x height):
Casing degree of protection:
Weight:
10BaseT Ethernet
TCP, ICMP (ping), DHCP server, http server
300 B
RJ45
2, internal in RJ45 socket
2.4, 4.8, 9.6 ,19.2, 38.4, 57.6, 115.2 kbps
1 start bit, 8 data bit, 1 stop bit (1 b or 2 stop bit for None)
Even, Odd, None1, None2
300 B
A(+), B(-)
32 eceivers / transmitters
internal, switched by relay
54Ω
1200m
- 8V - 13V
1,5V (for R0= 54Ω)
200mV / RWE= 12kΩ
Yes
2, TxD and RxD signalization, yellow colour
24VAC (+5% / -10%) / 1VA
24VDC (8 do 30 VDC) / 0,9W
1, presence of power supply, green colour
-20oC do +60oC / -30oC do +70oC
5 – 95% (without condensation)
93mm x 57mm x 21mm(without clip for DIN rail)
IP 30
about 0,06kg
SaoCal Net/122k10/HUSTY/INSTRUKCJA
INTERFACE ETHERNET
Interface: Supported protocols
Data buffer:
Socket:
LED diodes:
RS-485 SERIAL INTERFACE
Baud rate:
Data frame:
Parity control:
Data buffer:
Signals on terminal:
Maximum load:
Line terminator:
Minimum impedance for data transmission line:
Maximal line length:
Maximal voltage on terminals A(+) and B(-):
Minimal transmitter output signal:
Minimal receiver sensitivity:
Short-circuit / thermal protection:
LED diodes
13
SaoCal Net/122k10/HUSTY/INSTRUKCJA
6. MANUFACTURER
14
SaoCal Net/122k10/HUSTY/INSTRUKCJA
7. NOTES
15