RG500_chassis_files/High Speed Damping peter verdone

Peter Verdone Designs - High Speed Damping
06/24/2006 11:28 AM
High Speed Damping, Valves
I've been putting a lot of time into understanding all of the different valve designs out there.
I am getting convinced that the Ohlins fork valve kits are really the way to go. They repair most of the problems
with the Honda HMAS valves and do not flow too much oil like the Racetech valves. Dan Kyle is the "go to
guy" in the US for these.
If any information contained
in this site is not completely
accurate, is vauge, or flat
out wrong, please contact
me by e-mail immediately
and I will address the
problem.
Motorcycles:
Introduction
Suspension
Springs
Oil Height
Understanding Damping
Low Speed Damping
High Speed Damping
Oil Locks
Passive Elements
Geometry
Ride Height & Sag
Squat & Jack
Castor &Trail
Gearing
Understanding gearing
Choosing a FDR gear
Speedometer Recalibration
Chains & Sprockets
Tires
Lubrication
Motor Oils
Oil Filters
Oil Filter Testing
Fuel
Understaning The System
The Throttle
Power Comanders
Gasoline & Octane
Rider Position & Controls
Feet
Hands
CRG Levers
Windscreen
Saddle
Breaking in a New Bike
Wave Rotors
Plumbing
Special Tools
About Torque Wrenches
Books to Own
2005 Honda CBR600RR
General
Break-in
Forks
Shock
Gearing
Yoyodyne Slipper Clutch
Speedometer Recalibration
Yoyodyne Throttle
HRC Throttle
Tapered Roller Head Bearings
PAIR / SMOG Removal
Power Commander & Map
Double Bubble Windscreen
AIM Laptimer & Mount
CRG Shorty Levers
TCM Rear Rotor Modification
1000RR Radial Master
Factory Evo Star Shift Kit
Frame Sliders
2001 Honda CBR600F4i
2004 600RR Shock Disassembly
Forums & Links
Dan Kyle Suspension Seminar
That said, they will still require modification to reduce turbulence; ie. heavy chamfering of the back side of the
refill and valve ports, they will need some lapping to make a perfect shim seal prior to installation, and the
actual valve port size may need some fine tuning depending on how you use your fork and how it is set up.
For reasons stated earlier regarding the factories desire to make a bike that will work reasonably well for a
fixed price point, most stock cartridge damping systems are designed for saftey and economy rather than
performance. The cheapest hole to make is, of course, round. Also, to prevent excessive travel in high speed
by heavy riders or really hard hits the ports are small. By opening these ports up, the fork will be able to move
at much higher speeds and the shim stack exclusively will adjust the high speed damping curve. A high flow
compression valve is a very good tune to make for riders that push their bike very hard and are looking for superior suspension
performance. The sequence of the shim stack serves two functions. one is to determine when the H.S. valve starts functioning; two is to determine the
shape that the damping curve that the H.S. circuit will form in the transition region of the damping curve.
Shim stacks can be constructed in single, two, or three stage configuration. Sportbikes tend to have a single
stage stacks. motocross bikes tend to have two stage stacks. It isn't that a single stage stack is really better or
worse than the multi stage stacks, it's just that it makes tuning far simpler with very good results.
Learn more about how to stack shims HERE.
Formula for Conversion Between Shim Thickness:
(N1) * (M1) / (M2) = N2
Formula Key:
N1 = Number of shims to replace.
M1= Factor of the shim to replace.
M2=Factor of replacement shim.
N2= Number of replacement shims.
Lists of Shim Thickness and Factors (M)
Thickness Factor
Shim Thickness Moment of 17mm shim Moment of 22 mm shim Conversion Factor (M)
0.10 mm
0.00481
0.00635
1.00
0.15 mm
0.01622
0.02143
3.37
0.20 mm
0.03846
0.05081
8.00
Working Example:
We have (10) 0.10mm’s
We would like to replace them with 0.15mm’s.
(10) * (1) / (3.37) = 3 (or (3) 0.15mm shims)
This conversion is obtained by doing a simplistic moment of inertia calculation on different shim thicknesses.
This does not compensate for the non-uniform sectional area on the shims, but it is valid enough for
comparison.
Skateboard:
PVD Pro Slalom Trucks
Bearings & Lubrication
Skateboarding and the Law
Removing Skate Prevention Blocks
General Info
My Story
Bicycle:
http://www.peterverdonedesigns.com/highspeed.htm
Page 1 of 8
Peter Verdone Designs - High Speed Damping
06/24/2006 11:28 AM
Bicycle:
Shimano Mineral Oil
HollowTech II Bottom Brackets
Bicycle Chains
Chain Cleaning and Lube
Suspension
Choosing One -Speed Gears
Wheels
Wheel Components and Disk Wheel
Lacing Patterns
General
GPSracing:
GPS Dynomometer
Media:
Photo
Video
Sound
Resume:
Resume
Portfolio
Solid Models
References
Contact
These pictures are of the ultra high end K-tech 25mm Cartridge Fork Internals.
The picture below shows a stock Showa cartridge fork compression valve (right) and a Race Tech Gold Valve
replacement (left). you can see how much more oil the Gold Valve will pass compared to the stock part.
http://www.peterverdonedesigns.com/highspeed.htm
Page 2 of 8
Peter Verdone Designs - High Speed Damping
06/24/2006 11:28 AM
Below is a picture from Dan Kyle's website.
http://www.peterverdonedesigns.com/highspeed.htm
Page 3 of 8
Peter Verdone Designs - High Speed Damping
06/24/2006 11:28 AM
Here is a picture of Öhlins, Honda 4 port (HMAS), Racetech goldvalves and Showa 3 port (from a Suzuki very similar to Honda 3 port).
Top two rows are rebound and bottom two rows are compression.
First row shows the shim face for all rebound valves and for compression valves row three shows shim face for
Öhlins and RT and fourth row shows shim face for Showa.
Above is from an artical by Max McAllister
A Showa/Honda RS250 GP 25mm valve.
http://www.peterverdonedesigns.com/highspeed.htm
Page 4 of 8
Peter Verdone Designs - High Speed Damping
06/24/2006 11:28 AM
A vavle from a Fox shock:
Compression
rebound
Below is a worksheet I made in an attempt to understand how the number of ports change the flow of the oil
and bending shape of the shims. Clearly, the 3 port design is the most flexible and efficient design. I cannot for
the life of me understand 4 or 5 port valves. Why do Showa and Ohlins do it?
http://www.peterverdonedesigns.com/highspeed.htm
Page 5 of 8
Peter Verdone Designs - High Speed Damping
06/24/2006 11:28 AM
Modifying the valves
Below is a picture of a pair of Showa GSX-R valves that I performed some very conservative mods on. Note
the polished face finish, the large champher on the back side of the compression ports and the slight champher
on the back side of the refill port. This is done to ensure proper sealing and reduce turbulance of the oil during
flow. Reducing turbulance is very important when modifying valves. Any amount of turbulance effectively
shrinks the orfice size.(stock is on the left)
http://www.peterverdonedesigns.com/highspeed.htm
Page 6 of 8
Peter Verdone Designs - High Speed Damping
06/24/2006 11:28 AM
below is a fairly wild valve mod by zenostoic (James) -
Understanding and tuning Honda HMAS valves.
My current take on them is that they initially offer some transitional high speed damping like a high flow valve, but they then begin to
behave more like an orifice as the speed reaches peak, in general, progressive high speed damping.
The Ohlins valves are very similar to the Honda valves. What do you do with the ohlins valves? Can you really notice the difference going
from Honda to Ohlins ?
I also figure that the shim stack may become far more of a factor with these valves when using an ISO 15 fluid rather than the stock ISO
37 fluid. Reducing the oil height to a more realistic height than stock, so that the shock isn't ramping up like crazy regardless of high
speed damping, is certainly a necessity.
I'm going to attempt to work with them on my next bike, since I never really worked with them on my current bike before switching to the
race tech high flow valves. I'd just hate to feel that i didn't give a good part it's due before changing it.
The facts for 20mm fork: (compression and rebound are identical other than the o-ring
seal/bushings)
4 x 1.8 mm valve ports
4 x 2.8 mm refill ports
each valve port area - 2.54 mm^2
all valve port area - 10.18 mm^2
each refill port area - 6.16 mm^2
all refill port area - 24.16 mm^2
rod diameter - 10 mm
rod area - 78.54 mm^2
http://www.peterverdonedesigns.com/highspeed.htm
Page 7 of 8
Peter Verdone Designs - High Speed Damping
http://www.peterverdonedesigns.com/highspeed.htm
06/24/2006 11:28 AM
Page 8 of 8