Simple Receiver (SRX)

Transcription

Hendricks QRP Kits
Simple Receiver (SRX)
Inexpensive CW Receiver for 30 and 40m
Superhet receiver with high level mixer, AGC, and active R/C audio filtering
by Dan Tayloe, N7VE
SRX-30/40 v1
5-5-2013
Page 1 of 50
Table of Contents
Receiver .................................................................................................................................................. 4
Building the Kit....................................................................................................................................... 5
Things you will need ............................................................................................................................... 5
Parts List ................................................................................................................................................. 7
Tools and Construction Hints ............................................................................................................... 10
Bare PC Board Pictures ........................................................................................................................ 11
Installation of Main Tuning and Band Segment Switch ....................................................................... 12
Installation of the resistors part 1 .......................................................................................................... 15
Installation of the resistors part 2 .......................................................................................................... 18
Installation of the capacitors part 1 ....................................................................................................... 21
Installation of band specific Rs and Cs ................................................................................................. 28
Installation of Inductors ........................................................................................................................ 30
Installation of misc items, part #1 ......................................................................................................... 34
Installation of misc items, part #2 ......................................................................................................... 39
Installation decals on chassis ................................................................................................................ 41
Installation of receiver into chassis ....................................................................................................... 42
VFO alignment...................................................................................................................................... 46
List of Figures
Figure 1. Working over an oversized cookie sheet is highly recommended ............................................. 5
Figure 2. A temperature controlled soldering helps a lot........................................................................... 6
Figure 3. A very pointed soldering iron tip is a big help for small components ....................................... 6
Figure 4. Headband Magnifiers. “Mag-eyes” from JoAnn Fabrics .......................................................... 7
Figure 5. Top side view of the SRX PC board ........................................................................................ 11
Figure 6. Overlay of the PCB with band segment switch and main tune polyvaricon cap ..................... 12
Figure 7. Temporarily mount PCB in chassis .......................................................................................... 12
Figure 8. Prepare the leads of the main tuning capacitor ......................................................................... 13
Figure 9. Mount the main tuning cap to the front panel .......................................................................... 13
Figure 10. Solder main tuning cap leads from the top side of the PCB ................................................... 13
Figure 11. PCB with main tuning cap and band segment switch installed .............................................. 14
Figure 12. Example of overlay resistors vs. PCB mounted resistors ....................................................... 15
Figure 13. Resistors are mounted vertically, with short leads, body on the circle, close to the PCB ...... 16
Figure 14. First set of resistors installed .................................................................................................. 16
Figure 15. Resistors installed in this section ............................................................................................ 17
Figure 16. PCB with first set of resistors installed .................................................................................. 17
Figure 17. Overlay for the next set of resistors plus some diodes ........................................................... 18
Figure 18. Picture of resistors installed in this section ............................................................................ 18
Figure 19. Match 1N4148 diode band with board diode band ................................................................ 19
Figure 20. All 1N4148 diodes shown as mounted on the PCB ............................................................... 19
SRX-30/40 v1
5-5-2013
Page 2 of 50
Figure 21. PCB with all the resistors installed ......................................................................................... 20
Figure 22. Overlay for the first set of installed capacitors ....................................................................... 21
Figure 23. Capacitor markings for the first set of capacitors installed .................................................... 21
Figure 24. PCB with first set of capacitors installed ............................................................................... 22
Figure 25. Overlay of the installation of second set of capacitors ........................................................... 23
Figure 26. Markings on the second set of capacitors to be installed ....................................................... 23
Figure 27. Lead form the 470 pf polystyrene caps and mount vertically as shown ................................ 24
Figure 28. PCB with second set of capacitors installed. .......................................................................... 24
Figure 29. Overlay of third capacitor set plus misc parts ........................................................................ 25
Figure 30. Parts installed in this pass. Xtals, power diode, 5v reg, trim cap, 10 uf cap ......................... 25
Figure 31. D1 details. Note diode band orientation! Use trimmed leads for 12v input ......................... 26
Figure 32. PCB with crystals, diodes regulators, and part # 3 caps. 40m version shown. ..................... 27
Figure 33. PCB with band specific Rs and Cs installed. 40m version shown. ....................................... 29
Figure 34. Overlay of PCB showing inductor placement (with JFETs) .................................................. 30
Figure 35. JFET transistors, 1000/100 mH molded chokes, and VFO T37-2 core ................................. 30
Figure 36. Lead forming and mounting of molded chokes L2, L3, and L10 ........................................... 31
Figure 37. Band specific jumpers installed. 40m jumpers shown. ......................................................... 31
Figure 38. VFO coil L9. 40m version shown. ........................................................................................ 32
Figure 39. PCB with Inductors (and JFETs) installed ............................................................................. 33
Figure 40. Overlay of the installation of misc items, part 1 .................................................................... 34
Figure 41. Picture of parts installed this in this section ............................................................................ 34
Figure 42. Keep all transistors close to the PCB (short leads!) ............................................................... 35
Figure 43. Notches on ICs line with outline on the PCB .......................................................................... 35
Figure 44. Lead forming for C45 ............................................................................................................. 35
Figure 45. L1 transformer. 40m shown: 29T primary, 3T secondary...................................................... 36
Figure 46. Primary and secondary winding connections of L1 to the board shown. 40m shown. .......... 36
Figure 47. Board with misc items part # 1 installed. ............................................................................... 37
Figure 48. Temporary installation of volume pot and headphone jack for testing ................................... 38
Figure 49. Overlay showing the last board mounted parts ...................................................................... 39
Figure 50. NE602 and 2N4401 parts shown ............................................................................................ 39
Figure 51. Installation of NE602. Match part and part outline notches. ................................................... 40
Figure 52. Completed receiver board........................................................................................................ 40
Figure 53. Visualization of PCB to chassis connections .......................................................................... 42
Figure 54. Mount PCB in case using four 4-40 screws ............................................................................ 42
Figure 55. Installation of main tuning hardware ....................................................................................... 43
Figure 56. Mounting of the headphone jack ............................................................................................. 43
Figure 57. Wiring of the headphone jack and volume control to the PCB ............................................... 43
Figure 58. Volume control pot mounted to the front panel ..................................................................... 44
Figure 59. Mounting of the antenna connector. ........................................................................................ 44
Figure 60. Connection of the 12v power jack to the PCB. ....................................................................... 45
Figure 61. Front and rear panel views with the mounted hardware (Headphones not included). ............ 45
Figure 62. Picture main tune set to the lowest frequency, band segment switch set to low freq ............ 46
Figure 63. View of VFO area and L1 front end area ............................................................................... 47
Figure 64. Picture of L9 with compressed and expanded windings for VFO fine tuning ....................... 48
Figure 65. Trimmer caps on this particular polyvaricon.......................................................................... 49
Figure 66. Trim cap to peak receiver front end ........................................................................................ 50
SRX-30/40 v1
5-5-2013
Page 3 of 50
Specifications and Features
As measured from current prototypes, some variance in performance is expected from unit to unit.
Receiver
Receiver Type: Superhet with a three crystal IF filter
Receiver sensitivity: Better than -120 dBm
Current Drain: ~ 17 mA at 12v.
Features:

Bus switch first mixer improves handling of high level signal (40m SWBC!)

AGC – Automatically reduces large signals

3 pole Crystal filter
o Single sided receiver reception
o Wider 500 Hz filter decreases “ringing” and listener fatigue

Audio gain chain incorporates active R/C low pass filter
o Reduces unwanted high frequency audio gain stage hiss
o Provides >30 dB additional attenuation for signals more than 2KHz away

Headphone level output with diode limiting –
o Protects your ears from static crashes or sudden strong stations

Band coverage provided in two ranges
o Each tuning range ~ 20 KHz wide
o On board switch selects upper or lower band segments
 40m covers 7.000 to 7.022 and 7.024 to 7.049 MHz (DX and QRP segments)
 30m covers 10.100 to 10.120 MHz

External “mute” input (active low)
o Reduces receiver gain by ~ 70 dB
o Receiver input protected to 5w when muted (only when muted!)
SRX-30/40 v1
5-5-2013
Page 4 of 50
Building the Kit
Things you will need
- Solder sucker (highly recommended) or solder wick
- Temperature control soldering iron with a fine tip
- Magnifying headpiece and/or magnifying glass. 3.5 power reading glasses may work also. Try them
on and check for focus at a 6 to 8” operating distance.
- Cookie sheet (highly recommended for building on top of in order to catch stray parts and most
importantly to reduce static discharge damage to parts.
Figure 1. Working over an oversized cookie sheet is highly recommended
SRX-30/40 v1
5-5-2013
Page 5 of 50
Figure 2. A temperature controlled soldering helps a lot.
Figure 3. A very pointed soldering iron tip is a big help for small components
SRX-30/40 v1
5-5-2013
Page 6 of 50
Figure 4. Headband Magnifiers. “Mag-eyes” from JoAnn Fabrics
As far as magnification, I think that common reading glasses may be just as good. Try 3.5 or 3.25
magnification glasses. Try them on and check the focus distance. Ideal is a focus distance of about 8
inches.
I use the above Mag-eyes with my normal 1.5x reading glasses. I can gang both the reading glasses and
the Mag-eyes together to get a really good, close up look at the parts. However, it does drive my eyes a
bits nuts switching from no glasses to glasses, to Mag-eyes, to glasses plus Mag-eyes.
Parts List
Below is a list of the all parts that are included in the kit:
SRX-30/40 v1
5-5-2013
Page 7 of 50
Table 1. Inventory of band generic parts
Capacitor list
Quantity
1
1
1
2
2
3
21
3
2
1
1
Value
2.2 pf NPO
150 pf NPO
270 pf NPO
470 pf
Devices
0.1 uf
10 uf
100 uf
40 pf trim cap, 6mm
C11
C33
C6
C19, C22
C9, C10
C17, C38, C47
C1, C3, C12, C13, C14, C15, C16, C23, C24, C25, C28, C29, C30,
C31, C32, C35, C39, C41, C42, C43, C44
C36, C40, C48
C45, C46
C18
Main tuning Polyvaricon
C1
470 pf Polystyrene
4700 pf
Diode, Transistors and IC list
Quantity
1
1N5817
1N4148
7
1
1
1
1
74HC4053
2
1
4
2N5485
2N4401
2N7000
Value
78L05
NE602
LM833
Devices
D1
D3, D4,D5, D6, D7, D8, D11
IC1
IC2
IC3
IC4
Q4, Q7
Q6
Q1, Q2,Q3, Q5
Resistor list
Quantity
Value
1
22
3
390
6
1K
1
3.9K
5
22K
2
47K
3
100K
1
1K panel mount (volume)
Devices
R15
R9, R21, R23
R2, R7, R11, R13, R18, R22
R14
R5, R6, R8, R12, R19
R3, R10
R1, R4, R17
J6
SRX-30/40 v1
5-5-2013
Page 8 of 50
Inductor list
Quantity
1
1
1
Value
Devices
T37-2
L9
L10
L3
100 uH molded choke
1000 uH molded choke
Case hardware list
Quantity
1
4
1
1
4
Value
Devices
CHASSIS
4-40 x .25 Pan HEAD SCREW
Small NORCAL KNOB
Large NORCAL KNOB
RUBBER FEET, 1/4" THICK
Misc hardware list
Quantity
1
1
1
1
2
1
1
1
1
1
1
1
1
Value
Hole plug – unused rear hole
1/8th stereo jack – Keyer paddles/Key input
BNC antenna jack (with ground lug, lock washer, and nut)
Panel Mount Power Jack
Polyvaricon mounting screw
Polyvaricon 1/4" nylon shaft
Polyvaricon shaft screw
3 feet # 32 gauge wire
2 feet # 28 gauge wire
12 inches hook up wire
PC board
Sub mini slide switch
Decal Sheet
Notes
Table 2. Band Specific Part Values
C2
C4
C5
C20
C21
C26
C27
C34
30m
22 pf
22 pF
56 pF
680 pf
680 pf
220 pf
220 pf
220 pf
40m
27 pf
27 pF
68 pF
470 pf
470 pf
150 pf
150 pf
270 pf
L2
10 uH
molded
choke
33 uH
molded
choke
R16
30m
L1
T37-6
(yellow
core)
T37-2
(red
core)
Y1,Y2,Y3,Y4
7.37 MHz
series
crystal
4.915 MHz
series
crystal
40m
220
390
SRX-30/40 v1
5-5-2013
Page 9 of 50
Tools and Construction Hints
In building this transceiver as well as others, I have had some problems. These fall into several different
categories:
1)
2)
3)
4)
5)
ICs mounted backwards
Resistors and capacitors not soldered to the right pads (#2 most common problem!)
Diodes installed backwards
Not all parts were installed
Leads not totally stripped on the toroid cores (#1 most common problem!)
Please learn from my mistakes. Each time an IC is mounted, check the mounting polarity twice before
soldering it in. I suggest checking the IC polarity, soldering down one corner pin, and then checking it
one more time before finishing the job. I think the old saying is “measure twice, cut once.”
I have once been bit by not mounting all the parts. Double check the pictures against your kit to make
sure things end up in the right place.
You may find that the components in the pictures may be slightly different from what is in your kit.
Parts can change from order to order.
This manual has been set up to build a section, and then test it. The tests are normally quite simple. This
should find most problems as we go from stage to stage rather than getting to the end and not knowing
where to start.
I found building the transceiver over a large cookie sheet eliminated the problem of dropping parts and
losing them. However, when doing the applied voltage tests, you should place a few sheets of clean
paper under the boards to keep them from shorting out against the cookie sheet.
Some parts are static sensitive! Please take the suggestion to build over a conductive surface like a
large cookie sheet and always touch the cookie sheet before touching any part after leaving and
returning to work.
This receiver can be built in about six hours.
SRX-30/40 v1
5-5-2013
Page 10 of 50
Bare PC Board Pictures
Figure 5. Top side view of the SRX PC board
SRX-30/40 v1
5-5-2013
Page 11 of 50
Installation of Main Tuning and Band Segment Switch
Figure 6. Overlay of the PCB with band segment switch and main tune polyvaricon cap
Figure 7. Temporarily mount PCB in chassis
SRX-30/40 v1
5-5-2013
Page 12 of 50
In order for the main tuning capacitor to be aligned properly, the main tuning capacitor needs to be
soldered to the PCB when the PCB is in the chassis and the capacitor is mounted to the front panel.
Mount the PCB in the chassis as shown above. Use all four mounting screws. The PCB will only fit in
the chassis one way. Prepare the main tuning capacitor leads by first bending the leads straight back,
then forming and trimming them as shown below.
Figure 8. Prepare the leads of the main tuning capacitor
Figure 9. Mount the main tuning cap to the front panel
The main tuning cap needs to be mounted to the front panel with the main tuning shaft centered as much
as possible as shown above.
Figure 10. Solder main tuning cap leads from the top side of the PCB
SRX-30/40 v1
5-5-2013
Page 13 of 50
Solder the main tuning cap leads to the top of the board. Then remove the board and capacitor from the
chassis and trim the tuning capacitor on the bottom side of the board if needed.
Next mount the band segment switch as shown below.
Figure 11. PCB with main tuning cap and band segment switch installed
SRX-30/40 v1
5-5-2013
Page 14 of 50
Installation of the resistors part 1
It is very easy to get resistors confused. 22 and 22K resistors, and 390 and 3.9K resistors are
easy to confuse. First start by sorting all the resistors into different piles, one pile for each resistor type.
You can use a volt-ohm meter to double check the resistor values as an additional precaution.
The seven resistor types in this kit and their associated color codes are:
100K (brown – black – yellow) – 3 resistor total
47K (yellow – violet – orange) – 2 resistor total
22K (red – red – orange) – 5 resistors total
3.9K (orange – white – red) – 1 resistors total
1K (brown – black – red) – 6 resistors total
390 (orange – white – brown) – 3 resistors total
22 (red – red – black) – 1 resistor total
These are the resistors common across all the bands. There are band specific resistors.
All resistors are mounted vertically. The base of the resistor is mounted on the circle portion of PCB
symbol, while the direction of the pad for the other lead is indicated by the square on the circle as shown
below.
Figure 12. Example of overlay resistors vs. PCB mounted resistors
Notice the “Rxx” designation on the overlay diagram and the placement of the real resistors on the
board. Again, the resistor body goes on the circle, and the resistor lead goes in the direction of the small
square on the circle. Note in particular R48 and R50 in the first drawing and the direction it indicates
for the lead side of the resistor. Compare that with the mounted resistor in the photo. Like wise, in the
second drawing, R56 at the bottom is pointed North-South (NS) while the other resistors above it are
pointed East-West (EW).
The overlay has exaggerated the correct resistor installation direction by the use of a colored rectangle to
indicate the proper orientation when a resistor is to be installed in a particular spot.
SRX-30/40 v1
5-5-2013
Page 15 of 50
It is easy to place a resistor in the wrong spot. I suggest placing the resistor in the board, spreading the
leads outward on the bottom to hold them into place, then double checking the parts placement a second
time before soldering the resistors in place and trimming off their leads.
Figure 13. Resistors are mounted vertically, with short leads, body on the circle, close to the PCB
Figure 14. First set of resistors installed
SRX-30/40 v1
5-5-2013
Page 16 of 50
Figure 15. Resistors installed in this section
As the parts are installed, it is recommended to both check the box below and cross off the part on the
picture above. Install the following parts in the following order:
Install 22 resistors (marked red – red – black).  R15
Install 390 ohm resistors (marked orange – white – brown).  R9,  R21,  R23
Install 1K resistors (marked brown-black-red).  R2,  R7,  R11,  R13,  R18,  R22
Install 3.9K resistors (marked orange-white-red).  R14
Figure 16. PCB with first set of resistors installed
SRX-30/40 v1
5-5-2013
Page 17 of 50
Installation of the resistors part 2
Figure 17. Overlay for the next set of resistors plus some diodes
Figure 18. Picture of resistors installed in this section
SRX-30/40 v1
5-5-2013
Page 18 of 50
Figure 19. Match 1N4148 diode band with board diode band
Figure 20. All 1N4148 diodes shown as mounted on the PCB
Install 1N4148 diodes.  D3,  D4,  D5,  D6,  D7,  D8,  D11 Mount the diode vertically as
shown above. Double check the polarity of the diode against the band on the board.
Install 390 ohm resistors (marked orange – white – brown).  R9,  R21,  R23
Install 1K resistors (marked brown-black-red).  R2,  R7,  R11,  R13,  R18,  R22
Install 3.9K resistors (marked orange-white-red).  R14
All resistors should be installed now except for R16 which is band specific. It will installed later with
other band specific parts.
SRX-30/40 v1
5-5-2013
Page 19 of 50
Figure 21. PCB with all the resistors installed
SRX-30/40 v1
5-5-2013
Page 20 of 50
Installation of the capacitors part 1
Figure 22. Overlay for the first set of installed capacitors
Figure 23. Capacitor markings for the first set of capacitors installed
SRX-30/40 v1
5-5-2013
Page 21 of 50
-
Install 270 pf cap (marked “271”)  C6
- Install 470 pf caps (marked “471”)  C19,  C22 Note: These 470 pf capacitors are
flat disc capacitors as shown. They are ***not*** the plastic/silver tubular 470
pf polystyrene capacitors that will be installed in the next section.
-
Install 0.1 uf caps (Marked “104”)  C1,  C3,  C12,  C13,  C14,  C15,  C16,
 C23,  C24,  C25,  C28,  C29,  C30,  C31,  C32,  C35,  C39,
 C41,  C42,  C43,  C44
Figure 24. PCB with first set of capacitors installed
SRX-30/40 v1
5-5-2013
Page 22 of 50
Figure 25. Overlay of the installation of second set of capacitors
Figure 26. Markings on the second set of capacitors to be installed
SRX-30/40 v1
5-5-2013
Page 23 of 50
Figure 27. Lead form the 470 pf polystyrene caps and mount vertically as shown
Install 470 pf caps (marked “470”)  C9,  C10 as shown above.
Install 150 pf cap (marked “151”)  C33
Install 2.2 pf cap (marked “2.2”)  C11
Install 4700 pf caps (Marked “472”)  C17,  C38,  C47
Figure 28. PCB with second set of capacitors installed.
SRX-30/40 v1
5-5-2013
Page 24 of 50
Figure 29. Overlay of third capacitor set plus misc parts
Figure 30. Parts installed in this pass. Xtals, power diode, 5v reg, trim cap, 10 uf cap
SRX-30/40 v1
5-5-2013
Page 25 of 50
Figure 31. D1 details. Note diode band orientation! Use trimmed leads for 12v input
Install  D1 1N5817. This polarity protection diode is used to protect against connecting the 12v power
backwards. See details below. Make sure the banded end connects to the hole as shown on the D1 board
markings. Double check the polarity of the diode against the photos above. Use the trimmed as
temporary leads for the input voltage as shown below.
Install crystals  Y1,  Y2,  Y3,  Y4. 40m uses 4.9152 MHz crystals, 30m uses 7.37 MHz crystals
Install 78L05 5v regulator IC  IC2 Make sure flat side of the IC lines up with flat side of
the PCB outline
Install 40 pf trim cap  C18
Install 10 uf caps (marked 10 uf)  C36,  C40,  C48 These caps have a “long” lead and a
“short” lead. The long lead is the “+” side of the cap. The long lead needs to go
through the cap hole marked with “+” on the board.
SRX-30/40 v1
5-5-2013
Page 26 of 50
Figure 32. PCB with crystals, diodes regulators, and part # 3 caps. 40m version shown.
 Quick test # 1: Connect 12v to the 12v input power leads. The current drain in this stage is
roughly 2.3 mA. At this point, the main current drain is the 78L05 5v voltage regulator. Disconnect the
12v when done.
SRX-30/40 v1
5-5-2013
Page 27 of 50
Installation of band specific Rs and Cs
30m parts
Use this list to populate the PCB above if you have the 30m version on the receiver.
2
22 pf NPO (marked “22”)
C2, C4
1
C5
3
C26, C27, C34
2
680 pf (marked “681”)
C20, C21
1
220 resistor marked red-red-brown
R16
SRX-30/40 v1
5-5-2013
Page 28 of 50
40m parts
Use this list to populate the PCB above if you have the 40m version on the receiver.
2
27 pf (marked “27”)
C2, C4
1
68 pf (marked “68”)
C5
2
150 pf (marked 151”)
C26, C27
1
270 pf (marked “271”)
C34
2
470 pf (marked “471”)
C20, C21
1
390 resistor marked (orange-white-brown)
R16
Figure 33. PCB with band specific Rs and Cs installed. 40m version shown.
SRX-30/40 v1
5-5-2013
Page 29 of 50
Installation of Inductors
Figure 34. Overlay of PCB showing inductor placement (with JFETs)
Figure 35. JFET transistors, 1000/100 mH molded chokes, and VFO T37-2 core
SRX-30/40 v1
5-5-2013
Page 30 of 50
Install 2N5485  Q1,  Q7 – Match flat side with board outline as shown above! Keep the
leads short on all devices – mount the transistor low to the board.
Figure 36. Lead forming and mounting of molded chokes L2, L3, and L10
Install 1000 mH caps (brown-black-red)  L3 as shown above. This is mounted on end with the body
on the circle portion like a resistor.
Install 100 mH caps (brown-black-brown)  L10 as shown above.
Install band specific molded choke  L2 as shown above.
30m: 10 uH (brown-black-brown)
40m: 33 uH (orange-orange-brown)
Figure 37. Band specific jumpers installed. 40m jumpers shown.
Install band specific jumpers as shown above:
30m: Using a lead scrap, bend into a “U” form and insert into  J2 and  J4
40m: Using a lead scrap, bend into a “U” form and insert into  J1 and  J3
Instructions for winding inductors
The first inductor to be wound will be L9. The toroid core (T37-2) has a red color. It is very important
to use the right number of turns! We will wind and install L9 first and will illustrate how to count
the number of turns.
SRX-30/40 v1
5-5-2013
Page 31 of 50
Cut xx” of green # 32 gauge wire. The number of turns used depends on the band the kit is being built
for. The VFO coil is tapped. This means that a certain number of turns of wire will be wound, a wire
loop for a tap will be formed, and then a second set of windings will be added.
30m: 10 turns - tap - then 31 more turns; 41 turns in total
40m: 13 turns - tap - then 39 more turns; 52 turns in total
Cut 28 inches of the # 32 wire. This is the thinner of the two wire types provided (#28 and #32 gauge).
The first turn is placed through the core from the bottom as shown below. Hold the short end on the
bottom, with the long end of the wire out the top of the core as shown below:
Figure 38. VFO coil L9. 40m version shown.
Above shows the winding sequence for a 40m VFO coil10 turn coil. On the “13 turn” picture, you can
count 13 turns on the inside of the coil, but only 12 on the outside. It is the inside turns that
counts! I always double check by counting the outside turns and add 1. Add turns to the
coil counter-clockwise with each new turn coming in from the bottom side. Look closely
at the 13 turn picture and you can count 13 turns on the inside of the core and 12 turns on the outside.
12 + 1 =13.
Double check all the coils you wind for the right number of turns!
Next the leads need to be trimmed and stripped. The enamel wire used in this kit is special in that it
strips more easily than normal with heat. I simply use a blob of solder on the end of the iron and start
from the cut end of the wire, burning off insulation and working towards the core edge. The burnt
enamel fowls the solder, so I keep adding fresh solder as I go.
It is very important that the twisted wire portion of the tap be properly soldered together. The #1
failure in kits can be traced to not properly stripping the leads of the toroid inductors. Use an ohm meter
to check from the “start” wire to the “end” wire to make sure the “tap” wires are properly soldered
together.
Install VFO inductor  L9 using a red T37-2 toroid core. The two ends of the coil L9 connect to pads
1 and 2 while the tap connects to pad 3 as shown below. The connection to pin 1 should be temporarily
soldered to the top side of the pad, while the other two wires (2 and 3) should be soldered through the
holes. This is because the frequency of the VFO will likely be too low, and turns will need to be
removed from the coil on the pad 1 side and soldering to the top of pad 1 will make that easier.
SRX-30/40 v1
5-5-2013
Page 32 of 50
 Check L9 to make sure it has good solder contact: Use an ohm meter and make sure there is a short
(i.e., zero ohms) between the pads 1, 2, and 3 that L9 is connected to.
Figure 39. PCB with Inductors (and JFETs) installed
roughly 8.5 mA. This number is not precise. However, if the current drain is a lot higher (like 15 mA),
there is probably a problem that needs to be resolved first before moving on to the next stage.
Disconnect the 12v when done.
SRX-30/40 v1
5-5-2013
Page 33 of 50
Installation of misc items, part #1
Figure 40. Overlay of the installation of misc items, part 1
Figure 41. Picture of parts installed this in this section
SRX-30/40 v1
5-5-2013
Page 34 of 50
Figure 42. Keep all transistors close to the PCB (short leads!)
Install 2N7000 transistors  Q1,  Q2,  Q3,  Q5 Keep all transistors low to the PCB with
short leads as shown below. Transistor flat side must match PCB layout!
Figure 43. Notches on ICs line with outline on the PCB
Install 74HC4053  IC1 Make sure the IC notch lines up with the notch on the PCB as shown above.
Install LM833  IC4 Make sure the IC notch lines up with the notch on the PCB as shown above.
Figure 44. Lead forming for C45
SRX-30/40 v1
5-5-2013
Page 35 of 50
Install 100 uf cap  C45 with the leads formed as shown above on top of IC4 (LM833) also as shown.
Install 100 uf cap  C46 Make sure the longer “+” lead goes through the “+” hole on the board.
Wind L1, a two winding resonate input RF transformer. The core type used for this transformer depends
on the band used.
40m: A red T37-2 toroid core is used
30m: A yellow T37-6 toroid core is used
Likewise, the windings are band specific also. Cut 18” of #28 (the thicker wire) for the primary
winding, 5” of #32 (the thinner wire) for the secondary winding.
40m: 29 turns primary (#28 larger gauge wire), 3 turns secondary (#32 smaller gauge wire)
30m: 22 turns primary (#28 larger gauge wire), 2 turns secondary (#32 smaller gauge wire)
The exact number of turns is very important! Please verify the right number of turns. The construction
of L1 is shown below. The primary winding is wrapped first (40m: 29T, 30m:22 T). In this case the
last lead wrap should end as the same point the other lead started as these two leads will be inserted as a
pair into the board. The secondary winding is wrapped in between the windings of the primary as
shown.
Figure 45. L1 transformer. 40m shown: 29T primary, 3T secondary
Figure 46. Primary and secondary winding connections of L1 to the board shown. 40m shown.
SRX-30/40 v1
5-5-2013
Page 36 of 50
 Install L1 – double check for the right number of turns for the band used (40m: 29T/3T, 30m:
22T/2T) Make sure to strip the leads up to the edge of the core as was done with L1.
 Check L1 to make sure it has good solder contact: Use an ohm meter and make sure there is a short
(i.e., zero ohms) between the two primary winding pads, and between the two secondary winding pads.
Figure 47. Board with misc items part # 1 installed.
SRX-30/40 v1
5-5-2013
Page 37 of 50
Figure 48. Temporary installation of volume pot and headphone jack for testing
Temporarily connect the volume control pot using some scrap leads as shown above. Next add the
headphone jack to that using more scrap leads as shown above. We will keep this arrangement until the
board is mounted in the chassis.
roughly 13 mA. This number is not precise. However, if the current drain is a lot higher (like 20 mA),
there is probably a problem that needs to be resolved first before moving on to the next stage.
 Quick test # 4: Connect headphones to the temporary headphone jack. With power applied and
the volume control turned all the way up, hiss ought to be heard. Touching R9 or R23 with a damp
finger (near the crystals and the front of the board) should produce a good 60 Hz “hum” to the
headphones.
Disconnect the 12v when done.
SRX-30/40 v1
5-5-2013
Page 38 of 50
Installation of misc items, part #2
Figure 49. Overlay showing the last board mounted parts
Figure 50. NE602 and 2N4401 parts shown
SRX-30/40 v1
5-5-2013
Page 39 of 50
Install 2N4401 transistor  Q6 Keep all transistors low to the PCB with short leads.
Transistor flat side must match PCB layout!
Figure 51. Installation of NE602. Match part and part outline notches.
Install NE602  IC3. Make sure the IC notch lines up with the notch on the PCB as shown above.
Figure 52. Completed receiver board
SRX-30/40 v1
5-5-2013
Page 40 of 50
Installation decals on chassis
The decals are applied the same as model decals. Cut around each group of text or symbols you wish to
apply. It doesn’t have to be perfect as the background film is transparent. Apply the decals before you
mount anything to the chassis. Use the above picture to get the correct spacing around the holes and
cutouts, as it is very easy to do a great decal installation and have a portion covered up with a knob
Thoroughly clean the surface of the panel to remove any oils or contamination. We have found
that moving the decals into position on bare aluminum chassis is difficult, due to the brushed
surface, so we advise pre-coating the chassis with the Krylon clear before applying the decals, and
then, after as well.
Trim around the decal. After trimming, place the decal in a bowl of lukewarm water, with a small drop
of dish soap to reduce the surface tension, for 10-15 seconds. Using tweezers, handle carefully to avoid
tearing. Start to slide the decal off to the side of the backing paper, and place the unsupported edge of
the decal close to the final location. Hold the edge of the decal against the panel, with your finger, and
slide the paper out from under the decal. You can slide the decal around to the right position, as it will
float slightly on the film of water. Use a knife point or something sharp to do this. When in position,
hold the edge of the decal with your finger and gently squeegee excess water out from under the decal
with a tissue or paper towel. Work from the center, to both sides. Remove any bubbles by blotting or
wiping gently to the sides. Do this for each decal, and take your time. Allow to set overnight, or speed
drying by placing near a fan for a few of hours. When dry, spray two light coats of matte finish, Krylon,
clear to seal and protect the decals, and allow to dry in between coats. All decals come with two
complete sets, in case you mess one up.
SRX-30/40 v1
5-5-2013
Page 41 of 50
Installation of receiver into chassis
Figure 53. Visualization of PCB to chassis connections
Figure 54. Mount PCB in case using four 4-40 screws
Remove the temporary headphone, volume pot and power leads, then mount the PCB as shown in the
chassis. It will only mount one way.
SRX-30/40 v1
5-5-2013
Page 42 of 50
Figure 55. Installation of main tuning hardware
After the PCB is mounted in the chassis, add the hardware for the main tuning cap. The tuning shaft
should be centered in the hole so that it does not touch the edges. After the tuning shaft hardware is
added, check to see if the shaft turns smoothly with no drag. If drag is felt, the two mounting screws
might be a bit too deep. If so, place 1 turn of the wire (#28 gauge shown here) under the screw to give
the tuning cap a bit more room.
Finally, add the tuning knob. It should not be mounted flush with the case, but should have a slight gap
so that it will turn without rubbing the case.
Figure 56. Mounting of the headphone jack
Mount the headphone jack to the front panel as shown. Do not install the volume control (shown above)
until after the headphone jack is wired to the PCB. Install the shorting wire between the left and right
side of the headphone jack if it is not still in place from the temporary installation. See above.
Figure 57. Wiring of the headphone jack and volume control to the PCB
SRX-30/40 v1
5-5-2013
Page 43 of 50
Wire the headphone jack to the PCB as shown above using a scrap piece of enameled wire. This is a
very low current connection, so the thinner #32 gauge wire can be used for this task.
Figure 58. Volume control pot mounted to the front panel
Mount the volume control to the front panel. Make sure the washer is on the inside of the case. Tighten
the mounting nut and add the knob. Finally, wire the volume control to the PCB as shown above in the
headphone picture. If in doubt, see the visualization diagrams at the beginning of this section.
Figure 59. Mounting of the antenna connector.
The antenna connector is mounted as shown on the back panel. A lead scrap is used to connect the
antenna connector center pin to the PCB. Ground connection to the antenna jack is provided via the
PCB mounting screw and standoff near that connector so that a connection to the antenna “ground” pad
is not really ineeded.
The center hole in the real panel is not used. A hole plug has been provided to fill that hole.
SRX-30/40 v1
5-5-2013
Page 44 of 50
Figure 60. Connection of the 12v power jack to the PCB.
Mount the 12v power jack and connect to the PCB as shown using scrap #28 gauge wire. As shown
above, the center power lug goes to the “+” side of the 12v power input, while the outer terminal goes to
the ground side.
The last step is to add the four rubber “feet” to the bottom of the case.
The receiver is now fully assembled. The next phase is tuning up the front end band pass filter and
setting the VFO on frequency.
Figure 61. Front and rear panel views with the mounted hardware (Headphones not included).
SRX-30/40 v1
5-5-2013
Page 45 of 50
VFO alignment
In order to set the VFO frequency, set the main tuning to the low frequency with the main knob set full
counter clockwise as shown below. Next set the band segment switch to the lower frequency segment
(slide set away from the board edge) as shown below. Between these two settings, the VFO will be set
to the lowest received frequency. In the end, we want this to be 7.000 MHz for 40m and 10.100 for
30m.
Figure 62. Picture main tune set to the lowest frequency, band segment switch set to low freq
The crystals used on 40m are 4.915 MHz crystals. Thus the VFO needs to set to 7-4.915 or 2.085 MHz
for 40m. For 30m, 7.37 MHz crystals are used so the VFO needs to be set to 10.1-7.37 or 2.73 MHz
for 30m.
There are three types of VFO tuning that will be done:
-
Removing turns from L9.
Compressing or expanding the turns on L9
Using the trimmers on the back of the main tuning capacitor
First, removing turns from the VFO coil L9 provides the initial rough tuning. The coil has been
designed with a couple turns to many.
Secondly, the VFO coil turns are wound “shoulder to shoulder” as tightly as they can. This leaves some
spare coil space unused. Expanding the coil turns will raise the frequency by roughly as much as
removing one turn. This is used for VFO fine tuning. Playing with expanding/compressing the winding
can get the receiver very close.
Finally, there are trimmers on the back of the main tuning cap which provide about 2 KHz of total
tuning range. These can be used to tweak the VFO right where it should be.
SRX-30/40 v1
5-5-2013
Page 46 of 50
A frequency counter can be used to set the VFO to the correct frequency. Connect the counter to the
“CNTR” jack as shown below. This point has a 2.2 pf coupling cap. Attaching the frequency counter to
this point will make the frequency a bit low, a bit under less than1 KHz. After the frequency counter is
removed, the final received frequency can be touched up by a combination of expanding/compressing
the L9 coil and adjusting the main tune trim caps.
Figure 63. View of VFO area and L1 front end area
The simplest way to set the VFO on frequency is to use a signal generator, like a DDS VFO, and use the
generator to feed an insulated wire that is placed close to L1. If an actual signal generator is used, set it
to a relatively large signal level such as -40 dBm. Now sweep the signal generator as listed below until
the signal generator signal is heard.
In either case, if a frequency counter or a signal generator is used the following step should be used to
set the VFO. Note that the VFO coil turns is deliberately set to start the VFO frequency low since it is
easier to remove turns than to add one back. If you are using the signal generator method, you may need
to search around a bit depending on exactly how many turns have actually been placed on L9. It is easy
to be off by one or two turns either way.
40m: Sweep 6.6 to 7.1 MHz. My receiver 40m started at 6.914 MHz while having L9 two turns short
as verified by counting turns in the pictures of the VFO coil.
30m: Sweep 9.5 to 10.2 MHz
The VFO should come up too low in frequency. The VFO is course tuned by removing turns from the
39T (40m) or 31T (30m) side of L9. This Each turn removed raises the frequency by about 30 kHz
(40m) or 60 kHz (30m). Expect to remove 2 to 4 turns (perhaps more) to get the VFO on frequency.
SRX-30/40 v1
5-5-2013
Page 47 of 50
The goal in removing turns (rough tuning) is to get within one turn of the final frequency. I.e., you
always want to end up low in frequency compared to the desired setting.
Assume 30 kHz (40m) or 60 kHz (30m) frequency change per turn removed and that the receiver is 150
kHz low. This 150 kHz difference means that removing 5 turns (40m) and 2 turns (30m) is needed to
get to less than 1 turn low in frequency. Don’t take all these turns off at the same time. Start by
removing one (if close) or two turns (if far away) at a time. These extra turns are removed from L9 at
the end (pad “1”) indicated by the figure above. This lead that should have been soldered to the top of
its pad to make it easier to unsolder and reattach when finished. Remove the one or two turns, cut off
the excess wire, tin the wire and re-solder it to the top of the pad. Now double check the received
frequency either using a frequency counter or a signal generator, sweeping the signal generator around
until it is again heard in the receiver. Each time a turn or two is removed, double check the frequency
shift and use that to estimate the next round of turns removal (if needed). Each time turns are removed,
cut off the extra wire, re-tin the lead, and solder it down to the top of pad 1 of L9. With the turns on L9
as compressed as possible, we need to get within less than one turn of the final frequency. Again, we
need to end up this “rough tune” step being low in frequency.
Figure 64. Picture of L9 with compressed and expanded windings for VFO fine tuning
When turns have been removed to less than one turn lower than the final frequency, the next step is coil
compression/expansion. L9 should have been wound with the turns “shoulder to shoulder” with no gaps
between the turns. This creates a “bare core” gap from the start winding to the end winding (pad 1 and 2
on the PCB). When the turns are spread out to cover more of this “gap”, the VFO frequency will
increase. Notice that it is not necessary to expand the turns evenly around core to increase the
frequency. See the pictured examples above.
SRX-30/40 v1
5-5-2013
Page 48 of 50
Figure 65. Trimmer caps on this particular polyvaricon
It is a bit difficult to get the edge frequency “right on” spreading and compressing the turns. There are
trimmers on the back of the main tuning capacitor which has roughly a 2 KHz of total frequency shift
which can be used to “fine tune” the final frequency if desired. The trimmer locations shown are for the
specific polyvaricon tuning cap that was used in this build. The one you get might have a different
configuration and you will need to experiment to see which one is used for the band you are building.
When the surface the receiver is bumped, a bit of “twang” might be heard in the receiver due to some
vibration of L9. If this is the case, it might be desirable to use a **small** amount of hot candle wax or
hot glue to stick the coil to the surface of the PCB. An alternative might also be to use a nylon 4-40
screw (1”), a nylon washer, and a nylon nut. 6-32 nylon hardware will work also. These nylon
components can be found at Ace Hardware or other hardware stores. These additions will shift the VFO
frequency, so it is not recommended to do this unless you want to go through another round of VFO
adjustments.
Never use glues to cement L9 into place! Some glues will ruin the operation of the VFO (like Gorilla
Glue, Super glue, or J B Weld are known problems). Do not risk this. Please stick with candle wax,
hot glue, or nylon hardware to stabilize L9 if it does have a vibration problem.
A note on VFO stability. For best drift performance, I have found that VFOs need to be “broken in” for
best VFO stability. I suggest leaving the rig on continuously for at least three days to accomplish this.
Since this is designed to be inexpensive (yet high performance!), the chassis is left open. Air
conditioning (summer) or heating (winter) drafts may cause drifting. If this is a problem a paper top
“shell” can be formed over the receiver to protect the VFO from drafts. You will need to cut a square
notch in the shell if you need to get to the band segment switch.
SRX-30/40 v1
5-5-2013
Page 49 of 50
Figure 66. Trim cap to peak receiver front end
The only thing left to do is to connect an antenna (or weak signal generator) and peak the receiver input
(trim cap C18) for the best signal reception. As both sides of this cap is “hot”, use very short, insulated
screw driver. A tuning tool is best for this purpose. A normal screw driver will detune the circuit and
potentially get a false peak.
At this point in time, the kit is done.
SRX-30/40 v1
5-5-2013
Page 50 of 50

Simple Receiver (SRX)

Transcription

Similar documents

Part 1: What is a Rockmite, Acquisition and PCB Assembly

Cencorp Depaneling

Audio Restoration Repair Philips CD650

Audio Restoration Repair Arcam AVR350 Receiver

March ing Band Photograph - Spirit of Waxahachie Indian Band

HB 125 HYDRAULIC CHAIN TENSIONER INSTRUCTIONS

www.bstreetband.com

BYOC Overdrive 2 Kit Instructions

Service Manual

Printable Version - Daily Commercial