Beşinci Ulusal Deprem Mühendisliği Konferansı, 26
Transcription
Beşinci Ulusal Deprem Mühendisliği Konferansı, 26
TIME HISTORIES FOR SEISMIC ANALYSIS OF STRUCTURES PROS AND CONS OF AVAILABLE METHODS Nicolas HUMBERT1, Irmela ZENTNER2, Paola TRAVERSA3, Frédéric ALLAIN4 ABSTRACT Due to increased potentialities of computers, it is nowadays possible to perform dynamic nonlinear computation of structures to evaluate their ultimate behaviour under seismic loads using refined finite element models. Nevertheless, one key parameter for such complex computations is the input motion, which may lead to important discrepancies in the results and therefore difficulties to deal with for engineering purpose. Like many codes worldwide, Eurocode 8 (EC8), allows to perform dynamic computation for seismic analysis of structures with the use of time histories. The method to get these accelerograms is not clearly defined by EC8, possible alternatives being (i) time histories selection in a waveform database, (ii) numerical waveform generation or (iii) a composite method using selection of recording with a scaling or a filtering step. However these methods are frequently presented in contradiction with each other: natural motions should give a less biased estimation of seismic load, or generated motions should not catch all the complexity of natural ones. The objective of this paper to evaluate these assertions using statistics based on heuristic cases (i.e. test case). For this purpose, each of the 10548 accelerograms in the NGA database is used as an input for a test case. For each test case, a time history is generated that matches several parameters of the natural one: response spectrum, strong motion duration or cumulative absolute velocity (CAV). Then a natural accelerogram is selected that matches magnitude, distance, soil condition, response spectrum (..) of the target. The numerical codes used in this work are Powerspec and Code Aster with an overall process that guaranties the representativeness of the generated motions. The selection process is a classical one based on macroseismic data, response spectrum and strong motion duration. The statistical evaluation of the NGA database compared to the new databases generated in this study allows us to give some recommendations on how to obtain input motion for the dynamic analysis. These recommendations are in the conclusion of this paper. 1 Engineer, EDF, Hydro Engineering Centre, France, nicolas.humbert@edf.fr R&D Engineer , EDF R&D, France, irmela.zentner@edf.fr 3 Seismologist, EDF – TEGG, France, paola.traversa@edf.fr 4 Engineer, EDF, SEPTEN, France, frederic-1.allain @edf.fr 2 1 INTRODUCTION This study uses the NGA database as input data for a large number of heuristic cases: each motion of the database is reproduced with the methods evaluated. The validity of a given method is then evaluated by its capacity to reproduce the NGA motion with an equivalent level of demand, for different types of mechanical models. Firstly, we present the input data (NGA database) and the methods used to generate or select the accelerograms. Secondly the evaluation method based on usual statistics and a Student Fisher estimator is described. Finally the results and the recommendations are presented. NGA DATABASE The NGA (Next Generation Ground-Motion Attenuation Models) project was a multidisciplinary research program coordinated by the Pacific Earthquake Engineering Research Center (PEER), in partnership with the U.S. Geological Survey and the Southern California. The main goal of the NGA project was to develop new ground-motion prediction models for shallow crustal earthquakes in the western United States and similar active tectonic regions. To attain this goal, a common ground motion database was implemented (Power et al., 2008). It consists of 3551 multicomponent records from 173 shallow crustal earthquakes, ranging in magnitude from 4.2 to 7.9. The NGA data collection includes acceleration time series of the multi-component recordings, pseudoabsolute-spectral acceleration at multiple damping levels and supporting information about the earthquakes and recordings. In particular, metadata consist of information about the record, the earthquake source, the strong-motion station, and the propagation path. NGA data were systematically checked and reviewed by experts and NGA developers (Chiou et al., 2008). For these reasons, the NGA database is a robust and statistically representative input motion for this study. Figure 1. Epicenter distribution of the 173 earthquakes of the NGA database (Chiou et al., 2008). 2 3 Figure 2. Magnitude and distance distribution of strong-motion records in the NGA database (Chiou et al., 2008). ACCELEROGRAMS GENERATION Different methods for the generation of accelerograms and numerous ground motion models are available in literature. One particular class of stochastic methods is based on the identification of a response-spectrum-compatible Power Spectral density (PSD). Vanmarcke was among the first to implement this approachfor engineering design (Simqke – Gasparini, 1976). Following models introduced non stationary features e.g. Preumont (1980 & 1985) and Mertens (1997). More recently, a module for the generation of artificial ground motion has been introduced in Code_Aster that addresses the above objectives. The two methods for the generation of accelerograms developed in this publication are based on POWERSPEC and Code_Aster. However these two codes are included in a selection process based on the recommendations of both, EC8 and ASN (Autorité de Sûreté Nucléaire, the French nuclear authority) guide 2.01: the generation of accelerograms is done using other parameter than spectral shape as target. For this reason, iterative generation process is implemented for both codes in order to fit parameters such as strong motion duration (Tstr), maximum velocity (Vmax), maximum displacement (Dmax), Arias intensity (Iarias) or Cumulative Absolute Velocity (CAV). THE NON STATIONARY MODEL IMPLEMENTED IN POWERSPEC POWERSPEC is a software developed by Westinghouse based on the work of Preumont and Mertens. The non separable PSD model implemented in Powerspec is presented in equation (1) : S , t A(, t ) G( ) 2 A, t t e ( )t (1) The α function has a polynomial evolution: 0 1 2 2 with α0, α1 and α2 determined with the strong motion duration target and two parameters xp and x0 , giving the evolution of the spectral content with the time. xp and x0 parameters represent respectively the decreasing rate of the number of cycles and the decreasing rate of the number of peaks. This parameter usually varies between 0. and 0.075. The way to determine these two parameters is developed by Saragoni (1974): the evolution of the central frequency is described by the exponential function (2) : C t 2 02 e X t (2) 0 POWERSPEC adds a new term to the Vanmarcke formula to identify PSD coherent with the target spectrum (Preumont 1985). Then iteration on the spectral content of the PSD is implemented to improve the adjustment with the target spectrum. Finally a polynomial correction (or «baseline correction ») is applied using equation (3) to avoid the drift on the displacement, obtained integrating twice the accelerogram. a a0 a1t a 2 t 2 (3) THE NON STATIONARY MODEL IMPLEMENTED IN CODE ASTER The detailed methodology for Code_Aster non-stationary model is described in the Code_Aster documentation (Zentner, 2013). Hereafter a quick overview of the process is given. The spectrum-compatible, non-stationary ground motion model based on the concept of evolutionary PSD (Priestley M B, 1965) implemented in Code_Aster uses a general formulation where ground motion is expressed as filtered white noise, close to the classical Kanai-Tajimi PSD model (Kanai, 1957 and Tajimi, 1960). Time dependency of the central frequency is introduced by considering the central frequency of the filter as a function of time, yielding an evolutionary PSD model, Eq. (4) S R , t R12 R22 2 2 0 (t ) 2 2 2 2 20 (t ) 2 (4) The parameters of this model, R1,R2,w0 and are identified by minimising the distance to the spectrum compatible PSD G (w). The variation of the amplitude is introduced by a deterministic modulating function h(t). The Gamma function and the Jennings&Housner model are proposed by Code_Aster. The obtained evolutionary PSD model will yield time histories whose median spectrum is close to the target. However, since the PSD is a parametrical model, exact matching is in general not possible. The equal energy criterion (Preumont 1985) allows then to conciliate the spectrumcompatible model h(t)2G(ω) with the evolutionary PSD h(t)2S(ω,t)S0(ω), where S0(ω) is the corrective term: 0 ht S R , t S0 dt 0 ht G dt T T 2 2 (5) Moreover, a high pass filter allows to remove the low frequency components of synthetic ground motion (ω² decrease), yielding non diverging behaviour of the integrated velocity and displacement time histories. The filtered PSD reads (Clough & Penzien 1975): S , t 2 2f 2 2i f f 2 S R , t (6) The filter frequency ωf is also known as the corner frequency in the literature (Rezaeian and Der Kiureghian, 2008). Iterations on the frequency content of the accelerogram are performed to adjust the spectral match. 4 5 METHODOLOGY FOR THE SELECTION OF STRONG MOTIONS The selection process is a usual two-step method (Buratti, 2008) based on (i) macroseismic parameters and (ii) accelerometric parameters. First, the 20 motions that best fit the macroseismic score presented in the following equation are selected: K1 k 0 M M TARGET 2 k1 logD / DTARGET 2 k 2 logVs30 / Vs30TARGET 2 , (7) with M the magnitude, D the hypocentral distance, Vs30 the mean velocity of shear waves in the last 30 meters, and k0, k1 and k2 fitted to minimize the distance between spectra (for this paper k0=0.3, k1=1, k2=1) Secondly, the 20 resulting motions are classified using a score on spectrum and strong motion duration. 30Hz K2 k Sp f Sp ' 0 TARGET f 2 df k 0' TSTR TSTR _ CIBLE , 2 (8) 1Hz with Sp the spectral acceleration, TSTR, the strong motion, and k’0 and k’1 fitted in order to represent the sensitivity of the model to each parameter, the for this study k’0=1.5 and k’1=1. Moreover, the selected motion cannot be linked to the same station, the same earthquake or an aftershock/main shock of the same earthquake that the accelerogram we try to reproduce. For the selection of natural motions we do not use any scaling factor or frequency filter. This type of composite method is not developed in this paper but gives results very close to the generation methods. EVALUATION OF THE GENERATION AND SELECTION METHODS The comparison of the level of seismic demand from natural and artificial time histories will be made on the 10 548 time histories of the NGA database and on each of the 6 fragility models. Based on this 52 740 comparisons, this paper will conclude on the eventual over-conservatism or bias of artificial accelerograms. Models NGA data Record 1 Record 2 ... Record 10548 Conclusions Statistical Analysis Figure 3. Overview of the process The three methods studied in this paper to obtain accelerograms (two methods of generation and one of selection) are evaluated with respect to the level of demand they give in mechanical models. Two issues are evaluated: first they have to be unbiased; secondly they have to be as precise as possible. These two issues are addressed by performing a statistical comparison between the design value obtained for each accelerogram of the NGA dataset and the generated or selected one. Bias is evaluated by the global distance between the “x=y” line and the plot. The Bias 1 N ln( D(acc AccNGA NGA )) ln( D(acc copy NGA )) , (9) Efficiency of the method is evaluated with the standard deviation of the “copy” data around the respective NGA data (with a natural logarithm as Eq. (10)). 1 N ln( D(acc AccNGA NGA 2 )) ln( D(acc copy NGA )) , (10) For purposes of clarity this paper gives an estimation of the number of computation needed to obtain a 30% precision on the mean result with a 95% confidence. The evaluation of this number is based on the Student-Fisher estimator (Viallet et al. 2005 & 2007). The main characteristics of this estimator are described in the next paragraph. Figure 4. Illustration of the validation process: left figure: OK, no bias, low SD / middle figure: NOK, bias (here over-conservatism) / right figure: No bias, but high SD DESCRIPTION OF THE STUDENT FISHER ESTIMATOR Student-Fisher law SN (N being its degree of freedom) is commonly used in statistics. Its main characteristic is to tend to a Normal law when N tends to infinity. This law is particularly appropriate to predict the average value of a population D based on the average value of the sample DAV and its standard deviation SD, for a desired confidence level and depending on the size of the sample N, considering the following expression. Where T0.05;N-1 is the Student-Fisher parameter taken for N-1 degrees of freedom and for the appropriate probability (0.05 unilateral for 95% confidence level in our case). See next table to get characteristic values of Student-Fisher parameter. Table 1. Student-Fisher Parameters for a confidence level of 95%. N 5 10 15 20 30 50 Confidence level: 95% (unilateral) t(0.05; N-1) t(0.05;N-1)/N1/2 2.13 0.95 1.83 0.58 1.76 0.45 1.73 0.39 1.70 0.31 1.68 0.24 This parameter is inverted in order to obtain the number of computations needed to obtain a given precision on the mean value. For this study the precision needed is taken equal to 30% and the confidence level equal to 95%. DESCRIPTION OF FRAGILITY MODELS SELECTED The structural damages produced by real earthquake and artificial time histories are evaluated on several simplified models, from the most linear, to the most non linear: Mono modal linear model: this model represents a structure or a material with one controlling mode which represent the majority of the mass. 6 7 Multimodal linear model: this model is a finite differences computation of a double mode structure or material. This model gives information of the capacity of the generation or selection method to represent a combination of solicitations. Model with hardening behaviour: this model has a bilinear behaviour. For this study it represents the first step to non linearity. (The equivalent linear models are not presented here but for reasonable level of distortion the result is close to the linear models) Force 1. 50E+02 1. 00E+02 5. 00E+01 Displacment 0. 00E+00 - 3. 00E- 0 1 - 2. 00E- 0 1 - 1. 00E- 0 1 0. 00E+00 1. 00E- 01 2. 00E- 01 3. 00E- 01 - 5. 00E+01 - 1. 00E+02 - 1. 50E+02 Figure 5. Schematic loops “force .vs. displacement” Hardening behaviour. Takeda behaviour: elastic-plastic model taking into account an hysteretic behaviour characteristic of structures under earthquakes, and finally, a simplified model based on the frequency degradation as a function of a damage index. Force 1. 50E+02 1. 00E+02 5. 00E+01 Displacment 0. 00E+00 - 3. 00E- 0 1 - 2. 00E- 0 1 - 1. 00E- 0 1 0. 00E+00 1. 00E- 01 2. 00E- 01 3. 00E- 01 4. 00E- 01 - 5. 00E+01 - 1. 00E+02 - 1. 50E+02 Figure 6. Schematic loops “force .vs. displacement” Takeda bilinear model. Stiffness degradation with the number of cycles: represents a soil behaviour Force 150 100 50 Displacment 0 - 1. 5 -1 - 0. 5 0 0. 5 1 1. 5 - 50 - 100 - 150 Figure 7. Schematic loops “force .vs. displacement” Stiffness degradation model. Elastoplastic model: sliding structure – cliff edge effect. The demand parameter for this model is the maximum displacement. Acceleration 0. 15 0. 1 0. 05 Displacment 0 - 0. 000006 - 0. 000005 - 0. 000004 - 0. 000003 - 0. 000002 - 0. 000001 0 0. 000001 - 0. 05 - 0. 1 Figure 8. Elasto-plastic model left: Schematic loops “force .vs. displacement”. Right: Acceleration vs. displacement - 0. 15 RESULTS FOR THE GENERATION WITH CODE ASTER Mono-modal behaviour Takeda behaviour Multi-modal behaviour Stiffness degradation with the number of cycles Hardening behaviour Elastoplastic Figure 9. Analysis of the validity of the generation process with Code Aster 8 9 RESULTS FOR THE GENERATION WITH POWERSPEC Mono-modal behaviour Takeda behaviour Multi-modal behaviour Stiffness degradation with the number of cycles Hardening behaviour Elastoplastic Figure 10. Analysis of the validity of the generation process with POWERSPEC RESULT FOR THE SELECTION OF NATURAL ACELEROGRAMS Mono-modal behaviour Takeda behaviour Multi-modal behaviour Stifness degradation with the number of cycles Hardening behaviour Elastoplastic Figure 11. Analysis of the validity of the generation process with the selection of natural motions ANALYSIS OF RESULTS The following table summarizes the results of the analysis. The three methods of generation/selection tested present no bias and are validated for linear and non linear analysis. The generation of accelerograms gives a higher precision than the selection of natural motions. This is mainly due to the fact that the sample of selected natural accelerograms includes variability on magnitude / distance and soil condition. These uncertainties are carried over to the result variability. Table 2. Analysis of the validity of results. MonoMultimodal Model with Takeda Stiffness Elastoplastic modal linear linear hardening behaviour degradation model model model behaviour POWERSPEC generation ASTER generation Sigma 0.11 0.15 0.19 0.24 0.33 1.1 Number of computations* 3 3 4 5 7 52 Sigma 0.07 0.09 0.24 0.25 0.35 0.72 Number of computations* 2 2 5 5 7 23 0.48 0.56 4.22 11 15 >100 SIgma 0.36 0.37 0.43 SELECTION of natural Number of 7 8 10 accelerograms computations* * number of computations needed to match a 30% precision on the result Codes and guides usually recommend using a minimum of 3 computations for linear models and 5 for non linear model. Based on this study, we propose to limit this recommendation using synthetic accelerograms. In the case of natural accelerogram selection, this number should be raised to 8 for linear models and 11 for non linear models. For models with stiffness degradation, we recommend a minimum of 7 accelerograms in the case of synthetic accelerograms and 15 in the case of natural accelerograms selection. For highly non linear models (such as sliding structures) the number of accelerograms required has to be discussed case by case. In any case, the number of computations has to be discussed depending on the type of model, the type of generation of accelerograms and the needed precision for the results. CONCLUSION The three methods studied in this paper are validated: the generation with either, Code_Aster, or Powerspec, as well as the selection of natural accelerograms from strong motion databases, do not show any bias for any degree of non linearity of the studied structure or material. The whole variability of the ground motions included in the NGA database can be reproduced using a numerical code with a sufficient degree of complexity (spectrum matching for a given damping / realistic evolution of amplitude / non stationary model). Moreover the accelerograms generation methods are not over-conservative and well reproduce the intensity of natural strong motion. However a computation based on a selection of natural accelerograms need a higher number of computations to reach the same level of precision on the mean result. Furthermore the main issue to obtain a dynamic analysis without any bias is not a software or a natural vs. artificial question. The quality of the study is based on the attention given to the interfaces between the seismic hazard assessment team, the dynamic computation team and the team in charge of the accelerograms generation. For this reason, we recommend the teams that realize dynamic study to follow these five steps: 10 11 Evaluation of the dynamic model retained to represent the behaviour of the structure, evaluation of the (structural?) parameters of influence for the model. Assessment by the seismic hazard study of the target for the parameters of influence determined by step 1 coherent with the level of hazard needed (cf. table 3). Generation or selection of the times histories that match the target (in mean value or each one). Dynamic assessment; Evaluation of the mean value with a Student Fisher coefficient. (e.g. mean+0.95 Standard-deviation for 5 computations and 95% confidence level) In case of a result judged over-conservative, go to step 3 and raise the number of time histories. The feedback proves that in most cases this is the pre-study (phase 1) that is missing. We recommend assessing systematically a pre-study of the structure or material before the seismic hazard study and then communicate to the hazard assessment team the needed parameters (damping value / sensitivity to duration, strong motion / effect of vertical or horizontal excitation, etc.). Table 3 gives in detail the main recommendations for the generation of time histories. Table 3. Recommendations for the generation of time histories Type of dynamic model Elastic + 1 main mode Elastic + multimodal several dampings Non linear Highly non linear Needed parameter for the time history generation Only spectrum with the damping of the structure or Spectrum for the minimal damping of the structure + strong motion duration (Tstr) or IARIAS or CAV Add a first computation to evaluate an equivalent damping for the structure and use this damping for the target spectrum. If this step is not possible, prefer a low damping for the target spectrum. Other parameters: at least TSTR (but the following parameters are recommended too: IARIAS, CAV, VMAX, DMAX or AMAX/VMAX + specific parameter for the study: e.g. De Biasio 2014. The chronological time evolution of the frequency content seems to have only a second order effect on the noxiousness of the time history, but this evolution can nevertheless be taken into account, especially if the eigen frequencies decrease with the number or the amplitude of the cycles. Idem non linear + Anticipate a large number of computations (more than 5) + prefer generation than selection of natural accelerograms in order to avoid a too large number of computations REFERENCES Bommer J J, Acevedo A B (2004) “The use of real earthquake accelerograms as input to dynamic analysis”, Journal of Earthquake Engineering 8, Special Issue, 1, pp. 43–91. Bommer J J, and Ruggeri C (2002). “The specification of acceleration time-histories in seismic design codes, European Earthquake Engineering” 16(1), 3–17. Buratti N. (2008) “Assessment of seismic safety: response surface approach and accelerogram selection issues” Phd. Chiou B., R. Darragh, N. Gregor and W. Silva (2008). “NGA Project Strong-Motion Database”, Earthquake Spectra, Volume 24, No. 1, pages 23–44. Clough R W and Penzien J, (1975). Dynamics of Structures. McGraw-Hill. Code_Aster, general public licensed structural mechanics finite element software, http://www.codeaster. Org De Biasio M, Grange S, Dufour F, Allain F, Petre-Lazar I, (2014) “A simple and efficient measure accounting for non-linear behavior of structures” submitted to Earthquake Spectra 2014. Gasparini D A, Vanmarcke E.H. “SIMQKE : Users manual and Documentation” Dept. of Civil Eng. Massachusetts Institute of Technology, (1976). Kanai K, (1957) “Semi-empirical formula for the seismic characteristics of the ground motion.” Bulletin of the Earthquake Research Institute, volume 35, pages 308–325. University of Tokyo, 1957. Mertens P G, Preumont A, (1997) “Improved Generation and Application of Artificial Time Histories and PSD Functions”, SMIRT 14 – K21/7 NGA database: http://peer.berkeley.edu/peer_ground_motion_database Power M., B. Chiou, N. Abrahamson, Y. Bozorgnia, T. Shantz and C. Roblee (2008). “An Overview of the NGA Project”, Earthquake Spectra, Volume 24, No. 1, pages 3–21. Preumont A, (1980) A method for generating artificial earthquake accelerograms, Nuclear Engineering and Design 59, 357-368 Preumont A, (1985) “The generation of non-separable artificial earthquake accelerograms for the design of nuclear power plants.” Nuclear Engineering and Design 88, pp. 185 Priestley M B, (1965), “Evolutionary spectra and nonstationary processes.” J. Royal Statistical Society, 27(2):204 – 237. Rezaeian S and Der Kiureghian A, (2008). “A stochastic ground motion model with separable temporal and spectral nonstationarities”. Earthquake Engineering & Structural Dynamics, 37(13):1565–1584. Saragoni G R, Hart G C, (1974) « Simulation of Artificial Earthquakes » - Earthquake Engineering and Structural Dynamics, Vol. 2, 249 – 267. Tajimi H. (1960) “A statistical method of determining the maximum response of a building structure during an earthquake.” In 2nd WCEE, pages 781–798, Tokyo. Takeda, T., Sozen, M. A., and Nielsen, N. N. (1970). „„Reinforced concrete response to simulated earthquakes.‟‟ J. Struct. Div., ASCE, 96(12), 2557–2573. Viallet E, Heinfling G, (2005) “Natural And Artificial Time Histories For Non-Linear Seismic Studies : Which are Better ?”, SMIRT 18 - K09-3 – Beijing Viallet E., Humbert N. (2007) “Considerations on the Use of Natural and Artificial Time Histories for Seismic Transient Non-Linear Analyses of Structures and Variability Assessment” SMIRT 19, Toronto Zentner I. (2013), Code_Aster Documentation R4.05.05 Génération de signaux sismiques. http://www.codeaster.org/V2/doc/default/fr/man_r/r4/r4.05.05.pdf. 12