Product info Installation overview, Mover®

Product info
Installation overview, Mover® 01.2015
MANOEUVERING SYSTEMS
Fitting the Truma Mover® to chassis made by different manufacturers
Mover® XT, XT2 and XT4
Mover® XT L
Mover® SE R, TE R and TE R4
Mover® SR
The mounting set is included in the scope of delivery Various mounting sets are available as accessories for fitting to
almost any chassis.
More comfort on the move
Product info
Installation overview, Mover® Installation dimensions
Installation of a Mover® is possible for tyre sizes of between
165/70 R13 and 225/70 R15.
In order for the lateral bar of the Mover® to be affixed using
the mounting set, sufficient space must be available on the
underside of the frame. To determine whether this is the
case, a distance 1 (mm) needs to be measured (either
in front of or behind the axle) from the tyre. If there is an
attachment (that cannot be moved, e.g. a waste water tank)
or a joint in the chassis in this location, the short mounting
set cannot be used as an alternative mounting. The Mover®
XT L can only be fitted behind the axle using the XT L
mounting set.
The distance from the bottom edge of the frame to the
ground must be at least 170 mm, to ensure a final floor
clearance of 110 mm once installation is complete.
XT, XT2, XT4
The following distances must be adhered to when the
Mover® is swivelled out:
110 mm minimum floor clearance of laden vehicle
20 mm between the drive roller and the vehicle tyre
When the optimal distance between the tyres and the drive
rollers is set, the tyres must be under load.
Installation over a pit is therefore simpler than with an auto
hoist. After installation, if an auto hoist is used, the caravan
must first be lowered before the distance between the drive
rollers and the tyres can be set.
Please pay attention to the additional notes in the relevant
installation instructions!
320
Caravan base
1
XT L
max. 20
140
min. 25
U-profile
min. 35
min.
170*
160
110*
min.
min.
140
L-profile
min.
20
min. 80 / max. 180
min. 1350 / max. 2000
20
Caravan base
5°
min. 160
110*
ca. 1400
Direction of travel
S(R)
340
Caravan base
20
max. 20
min.
XT L
min.
170
L-profile
SE(R), TE(R)
min. 25
U-profile
1
min.
170*
110*
106
min.
min. 35
min. 50 / max. 180
min. 1200 / max. 2000
All dimensions in mm
* for loaded vehicles with maximum allowed total weight
2
Product info
Installation overview, Mover® Mounting set
The mounting set (picture 1 – included in scope of delivery
of the Mover® XT, XT2, XT4) suitable for all standard L-profile
and U-profile frames, likewise the predecessor model
(picture 3).
In the event of deviating frame conditions or substructures
and interfering edges, installation can be achieved using
special accessories – see Chassis variants and accessories
overview.
Extra reinforcement is required for AL-KO chassis with
a frame thickness of less than 2.8 m – see mounting
of variant 5a. No other accessories are required for the
Mover® XT L, and the height of the mounting set differs
(picture 2).
Attention:
You must not drill into* or weld onto the vehicle frame.
* Exception: when using the flat frame kit with chassis from
various manufacturers – see Accessories overview.
Wheel suspension parts must not be removed under any
circumstances.
1
50
50
2
XT
Mover® XT, XT2
as of model year
07/2013
L
Mover® XT4
as of model year
01/2014
XT L
Mover® XT L
as of model year
07/2013
5°
XT
L
40
50
Mover® SR
as of model year
05/2012
3
Mover® S
up to model year
04/2012
Mover® SE R
and TE R(4)
as of model year
05/2012
Mover® SE and TE
up to model year
04/2012
3
Product info
Installation overview, Mover® Chassis variants overview
Tip: You can find the chassis model on the vehicle registration certificate/manufacturer's plate on the chassis
Chassis
manufacturer
Model
Weight
Base length
Installation variant
(see page 5 – 8)
BPW
Vario IV one piece (picture 1)
up to 1300 kg
no data
1a or 2
BPW
Vario IV (picture 2)
1500 - 1800 kg
up to 5500 mm
4
BPW
Vario IV reinforced (picture 3)
1500 - 1800 kg
from 5500 mm
1b
BPW
Vario III one piece
no data
no data
3
BPW
Vario III two piece
no data
no data
3
AL-KO
Vario III /AV
with entry step
1800 kg/
up to 1700 kg
no data
no data
5a
5a and 7
AL-KO
Vario IV
AL-KO
M (with axle shift)
up to 1800 kg
5b or 1a behind the axle
AL-KO
M (continuous frame)
1900 - 2000 kg
5c or 1a behind the axle
AL-KO
Lightweight chassis
up to 1500 kg
1c, only with Mover® XT L
5b or 1a behind the axle
Example illustrations of BPW chassis
Vario IV one piece
Vario IV
1
Vario IV reinforced
2
3
Special models overview
Caravan
manufacturer
Model
Installation variant
(see page 5 – 8)
Hymer
Eriba Touring (except Puck)
8a
Hymer
Eriba Troll
8a in front of axle or
8b behind the axle
(if little space available)
Hymer
Nova L 380, 425, 450, 470
Feeling 230, 380, 425, 470
1c, only with Mover® XT L
(Feeling 230 with spacer piece
if necessary and
Mover® XT)
Fendt
Bianco: 445 TFB
Saphir: 470 TFB, 490 TF, 510 TFB
Platin: 470 TFB, 510 TFB
Topas: 490 TF, 510 TFB, 520 TFB
6
Knaus Tabbert
W03 Eurostar:
500 EU, 500 FU 590 FUS
W23 Grande Puccini: 490 EU, 590 TD, 655 DF, 750 HTD
W29 Supreme:
590 MDW, 630 MDW, 660 MDW
Accessories
Short mounting set, approved
for Mover® XT, XT2 und XT4
(see page 11)
4
Installation options overview
Option
Installation site
1a
L-profile or U-profile
Installation in front of the
axle
Installation behind the axle
1b
BPW Vario IV, reinforced
Installation on the
reinforcement brace
(Page 4, picture 3)
1c
2
3
4
Installation site illustration
Direction of travel
A1 / A2
Mover
Mover
–
–
XT-L
Mover
Mover
Accessories
(see page
9 – 11)
–
Mover
L-profile or U-profile
Installation behind the axle
Frame height of
< 140 – 110 mm (A1) or
frame height of
< 110 – 80 mm (A2)
L-profile or U-profile
Mounting in front of or
behind the axle, frame
height less than 110 mm, for
greater ground clearance
Mover
Mover
AL-KO lightweight chassis
mounting only possible with
Mover® XT L and only behind
the axis
L-profile or U-profile
Mounting in front of or behind the axle, frame height
less than 80 mm, for BPW 
Vario III one/two piece and
BPW Vario IV (Page 4, picture 2)
Profile illustration
(with accessories)
Mover
Mover
C1
C2
5
Installation options overview
Option
5a
Installation site
AL-KO Vario III/IV,
L-profile or U-profile
Frame thickness less than
2.8 mm
Installation behind the axle
only
5b
AL-KO Vario IV and
AL-KO Vario M
frame with axle shift
Montage in front of the axle
5c
AL-KO Chassis M
with continuous frame
Installed in front of the axle
6
7
8a
Installation site illustration
Direction of travel
Profile illustration
(with accessories)
D1
Mover
D2
as of
07/2013
Mover
D3
Mover
L-profile or U-profile
Installation below the entry
step
A1 / A2
Mover
AL-KO Vario III/AV
L-profile or U-profile
Frame thickness less than
2.8 mm. Installation below
the entry step
Rectangular profile
Mounting in front of or
behind * the axle
(minimum tyre size 14")
D1 +
A1 / A2
Mover
Mover
Accessories
(see page
9 – 11)
Mover
E1
* The waste water pipe system needs
to be moved!
8b
L-Profile
Installed behind the axle,
if 8a in front of the axle is not
possible due to lack of space
Mover
E2
6
Installation options overview
Option
1a
1b
2
Installation site
L-profile or U-profile
Installation in front of the
axle
Installation behind the axle
(not illustated)
BPW Vario IV, reinforced
Installation on the
reinforcement brace
(Page 4, picture 3)
L-profile or U-profile
Installation behind the axle
Frame height
110 – <170 mm
Installation site illustration
Direction of travel
Profile illustration
(with accessories)
Accessories
(see page
9 – 11)
–
–
B1 / B2
3
L-profile or U-profile
Mounting in front of or behind the axle, frame height
less than 110 mm, for BPW 
Vario III one/two piece and
BPW Vario IV (Page 4, picture 2)
C1
4
L-profile or U-profile
Mounting in front of or
behind the axle, frame height
less than 110 mm, for greater
ground clearance and for
BPW Vario III one piece
C2
5a
AL-KO Vario III/IV,
L-profile or U-profile
Frame thickness less than
2.8 mm
Installation behind the axle
only
D1
5b
AL-KO Vario IV and
AL-KO Vario M
Montage in front of the axle
D2
5c
AL-KO Chassis M
with continuous frame
Installed in front of the axle
D3
7
Installation options overview
Option
6
7
8a
Installation site
L-profile or U-profile
Installation below the entry
step
AL-KO Vario III/AV
L-profile or U-profile
Frame thickness less than
2.8 mm. Installation below
the entry step
Rectangular profile
Mounting in front of or
behind * the axle
(minimum tyre size 14")
Installation site illustration
Direction of travel
Profile illustration
(with accessories)
Accessories
(see page
9 – 11)
B1 / B2
D1 +
B1 / B2
E1
* The waste water pipe system needs
to be moved!
8b
L-Profile
Installed behind the axle,
if 8a in front of the axle is not
possible due to lack of space
E2
8
Accessories overview
Spacer sets for mounting system
From construction year 05/2012
Item Accessory
A1
A2
Illustration
Spacer set 30 mm
Part number
60030-95000
Spacer set 60 mm
60030-95100
for
Mover®
Important notes
XT
XT2
XT4
To compensate a height of
30 mm for a frame height of
< 140 mm to 110 mm
SR2
SER
TER(4)
To compensate a height of
30 mm for a frame height of
< 170 mm to 140 mm
XT
XT2
XT4
To compensate a height of
60 mm for a frame height of
< 110 mm to 80 mm
SR2
SER
TER(4)
To compensate a height of
60 mm for a frame height of
< 140 mm to 110 mm
for
Mover®
Important notes
Spacer sets for mounting system
Up to construction year 04/2012
Item Accessory
B1
Spacer plates kit
Consisting of 2 x 15 mm
spacer plates
Illustration
Part number
60010-66000
SE(R)
TE(R)
S(R)
and
B2
For compensating for
heights of up to 45 mm
(corresponds to 3 spacer
plates kits)
and
Set of screws
Consisting of
8 screws (DIN 933)
M10 x 95 8.8
60010-70000
Spacer plates kit
Consisting of 2 x 4 15 mm
spacer plates, 8 bolts
(DIN 933) M10 x 110 8.8 and
nuts
60010-70500
Required for installing the
spacer plates kit
SE(R)
S(R)
For compensating for
heights of up to 60 mm for
single-axle caravans with
AL‑KO Vario III / AV chassis
and up to 1700 kg total
weight
9
Accessories overview
Can be used for both mounting systems
Item Accessory
C1
C2
D1
D2
D3
E1
E2
Illustration
Part number
for
Mover®
Important notes
Flat frame kit
Consisting of mounting plates
(each 240 mm high) including
bolts and nuts
60010-64900
XT
XT2
XT4
For compensating for a
frame height of less than
80 mm
SE(R)
TE(R)(4)
S(R)
For compensating for a
frame height of less than
110 mm
Flat frame kit, short
Consisting of mounting plates
(each 170 mm high) including
bolts and nuts
60030-37600
XT
XT2
XT4
To compensate a chassis
height of below 80 mm
and for greater ground
clearance
SE(R)
TE(R)(4)
S(R)
To compensate a chassis
height of below 110 mm
and for greater ground
clearance
XT
Mandatory for frame
reinforcement on caravans
with frame thicknesses of
less than 2.8 mm
Installation kit
AL-KO Vario III / AV
Incl. 6 bolts and 6 nuts
(M10 x 35)
60010-21500
Adapter set M
for AL-KO frames with
axle shift up to 1800 kg
permissible total weight
including 10 bolts (M12 x 40)
and 10 nuts
60030-38600
as of 07/2013
Adapter set M
for AL-KO with continuous
frame and 1900-2000 kg
permissible overall weight
including 10 bolts (M12 x 30)
and 10 nuts
60031-02000
Eriba Touring
installation kit
Incl. 4 bolts and 4 nuts
(M10 x 70)
60030-09000
Eriba Touring Troll
including 4 bolts (M10 x 30)
coated and 4 nuts
60031-03000
SE(R)
S(R)
XT
SE(R)
S(R)
XT
to compensate chassis
edges
Design-related structural
modification as of 07/2013!
Attention: up to 06/2013
the adapter set may not
be used to attach the
Mover® XT!
to compensate chassis
edges
SE(R)
S(R)
XT
For fitting a Mover® to a
chassis with a square profile
SE(R)
S(R)
XT
SE(R)
S(R)
for installing a Movers®
behind the axle if E1 is not
possible
Le Mover® et les accessoires mentionnés sont inclus dans l’attestation d’homologation générale (valable pour l’Allemagne) et
sont donc homologués en Allemagne. Une réception par le service des mines (TÜV) n’est pas nécessaire (exception voir Rep.
C1 et C2). Dans les autres pays, observer la réglementation correspondante.
10
Accessories overview
Short mounting system
Accessories
Illustration
Short mounting system
including distance of 30
mm and 60 mm
Part number
for Mover® Important note
60031-20000
XT
XT2
XT4
Alternative mounting if
attachment is not possible
because of substructures /
interfering edges
SR
SER
TER(4)
Attention: TÜV approval
is required for the
Mover® SR, SER, TER(4)
with the short mounting
system in Germany.
Mounting examples
11
Accessories
Part number:
Description
74102-01
SolarSet 23
for battery trickle charging for
Mover® PowerSet
incl. solar installation kit
Module output:
23 Wp
Solar battery charger SC 3: max. charging
current 3 A
Only available
from wholesalers
PowerSet light
for Mover® XT and Mover® XT2
Scope of delivery
BC 10 charger
–– 2 plug-in DC connector cables
for battery connection
(optionally with ring eyelets or clamps)
–– Temperature sensor
–– Easy clicK® diecast terminal clamps
–– Battery cut-off switch
Optima® YT S 2.7 (38 Ah)
Battery weight: 11.6 kg
PowerSet
for Mover® XT4 and Mover® SR
Scope of delivery
BC 10 charger
–– 2 plug-in DC connector cables
for battery connection
(optionally with ring eyelets or clamps)
–– Temperature sensor
–– Easy clicK® diecast terminal clamps
–– Battery cut-off switch
Optima® YT S 4.2 (55 Ah)
Battery weight: 19.5 kg
47000-00800
Battery holder for OPTIMA® YT S battery
The battery holder ensures that the battery is
quickly and easily secured.
for OPTIMA® YT S 2.7,
OPTIMA® YT S 4.2 and
OPTIMA® YT S 5.5
(excludes battery)
The product infos for SolarSet and Mover® PowerSet can be found at www.truma.com under “Dealer Login”.
Truma Gerätetechnik GmbH & Co. KG
Wernher-von-Braun-Straße 12
85640 Putzbrunn, Germany
Telefon +49 (0)89 4617-0
info@truma.com
Service
Telefon +49 (0)89 4617-2010
Telefax +49 (0)89 4617-2159
service@truma.com
www.truma.com
The right to effect technical modifications is reserved!
– 18.06.2013 – Montage Mover® – GB
TSEhm
– 28.01.2015
Only available
from wholesalers