Opel Passion Newsletter Vol. 2
Transcription
Opel Passion Newsletter Vol. 2
INSIDE THIS ISSUE: “Opel’s In the Spotlight” 1. A classic Opel gets into the “Spotlight” on criminal minds & New GT Concept Car 2. Across America! A short story of why people own classic Opel's 3. Upcoming OGTS Events 4. Greetings From Gil 5. Opel Tech Tip: “this one is important” Classic cars are everywhere these days. Articles and images of classic cars show up on start pages like Yahoo, MSN, AOL, and all of the major TV media’s pages. Walk into a decent bookstore and the automobile section of their magazine racks are full of classic car articles and images. For years now, major manufactures have been reaching back to their glory days of individuality “retro designs” and trying to incorporate design cues from the good old days to no avail. 25—40+ years ago … an Opel was definitely an Opel. A BMW was a BMW, nothing else looked like a Mercedes, Jaguars had their own special look, same for Porsche, Alpha’s, Lotus, Pontiac, Buick, MG’s, etc. etc. etc. In short … the design cues from every manufacture had their own flavor and it was great! Continued on page 2 ... Photo by Maurice Van Sevecotte (not staged) Presented by Opel GT Source www.opelgtsource.com / www.opelgts.com Vol. 1 / Issue #2 “Opel’S In the Spotlight” continued - “Opel's In the Spotlight” continued - Things have changed as the years have passed and have blended into a vanilla flavor. Those individual design cues that separated the marquis’ have been diluted by the advancements in manufacturing. http://www.cbs.com/shows/criminal_minds/video/ aIS3rC25RWpX1A9tGEJPJFhGI2RYFf3O/criminal-minds -drive/ Enjoy! In today’s mega factories, a left-side is stamped, the right-side is stamped, the bottom & tops are stamped and the large machinery to produce these shapes have taken precedence over the free design of more hand built cars from our pasts when the panels were much smaller and led to more control over the design lines that were available to work with. http://www.caranddriver.com/news/opel-gt-conceptofficial-photos-and-info-news The image below was posted on Yahoo January 27, 2016 and illustrates what this article is about. Also in the spotlight the past few weeks … The NEW Opel GT Concept Car: The moral to this story is … We Opel owners drive cars that have more character, personality, and gorgeous design lines that cannot be created in production cars these days. To get anything close, you are in the 6 - 7 figure price range of today’s cars. Classic Opel’s are beautiful mechanical machines with tactile feedback for our senses to enjoy! (remove the badges & grills and it’s pretty vanilla) A current Chevrolet TV commercial shows a host bringing in a group of perspective buyers to look at a car with all marquis badges removed and asked if they can tell him who the manufacture is? The group of men and women are not able to identify who makes the car. Wow! Have things changed. It’s now the excepted design standard that if your car looks like every other car … that’s a good thing. Individuality has left the building! Now, back to our Opel's. Recently the Opel GT showed up on Criminal Minds (Season 11/Episode 12) that aired 1.20.2016 on CBS. The beautiful white GT is owned by Joe Mantegna, star of the popular TV show. It was restored with a fuel injected 2.0L & 5 speed tranny, Team Dynamics wheels, etc. from Opel GT Source. Go to this link to view the episode. The Opel GT shows up at (1:12 minutes) and (38:40 minutes) Continued in next column ... Presented by Opel GT Source www.opelgtsource.com / www.opelgts.com Vol. 1 / Issue #2 ACROSS AMERICA ~ (Dave Macey 1970 Opel GT in Dodge Viper Blue) I chose the Opel GT based on a love affair that started during a chance meeting with a high school friend after graduating in 1985. This friend was driving a GT, and it was for sale. As we were talking, I noticed the car had seen much better days. Rust bubbles had devoured a good portion of the front quarter tops. Being the great friend that he was, he convinced me that it was not the right car for me, but I was 18 and captivated! Over the next 8 years I searched for a car worthy of restoring. It was more a journey and a quest. In 1993, I found the GT I wanted to restore. It too needed a lot of work; For instance, Sporting Euro-type floppy mirrors and Escort GT plastic emblems, rust bubbles under the camouflage of thick black strips and Bondo. It was going to be a labor of love, but the vision was clear. That vision was a replica of my buddy’s car I fell in love with back in 1985! Wheels First and foremost were new tires and rims. A good friend told me about a great place to find some. It was an open warehouse full of wheels stacked (and un-stacked) on posts. I sorted through the piles and found one, then two, then three distinctive American Racing turbine rims with what looked like the correct pattern offset. Fortunately after rummaging around for what seemed like hours, the fourth one appeared. When it did, I took them to the counter and asked if I could try them on for size (luckily I brought the Opel with me). The guy laughed at me and stated, “You know, they only fit on three types of cars… MG, Vega, and Opel.” That was a good sign. To my good fortune, they fit perfectly! College and GT Parts Financing (1993-2000) I began working on a plan to work hard and put the rewards into my GT. While taking night classes and receiving employer tuition reimbursement, and with every successful A or B grade, 100 % went back into the dream. Over the years this financed and installed: Weber 38 DGAS Carburetor (to replace the Solex monstrosity), Crane CAMS electronic optical electronic ignition (points were always inconsistent), and front and rear stabilizer bars were just a few college gifts. Body (1997 – 2000) From the first visual inspection, rust bubbles were pretty extensive. Then, when it came time to clean out, that’s where the rust was found to be extremely pervasive. First, I started chipping away in small portions, and then, as I continued to dig, the rust was noticeably widespread. By the time I hit clean metal, I was totally through the rocker panel all the way through up to my wrist! So, out came the big guns. The dye grinder and reciprocating saw. When the cutting was complete, I swept away an enormous amount of rusty sand and chunks of deformed metal. It was now Frankenstein! With the help of some California friends (both big names in Opel's), I purchased clean cut west-coast rockers, and lower rear skins, reproduction lenses, NOS parts; original driver and passenger side view mirrors, and a beautiful new functional gas cap. The cutting and trimming of the metal to fit the existing body was more art than science. In the end, I put them together using a tongue and groove approach (Pop rivets and scraps of metal). Then, when it was all stitched together; it was taking shape and ready for welding. After that was completed, a friend recommended a body shop that could weld the pieces I stitched. They ran the welder over the lines and rivet holes, did a little grinding and it was done! A Single stage integrated clear paint was completed to perfection by Maaco. All glass, chrome and accessories were removed prior to paint. Choosing the paint color was easy, an updated version of that midnight blue car I wanted 1985--Dodge Viper Blue! Other notable projects include, sending out the dash and center console for recover, and outsourcing all chrome and stainless to be re-plated, straightened, and polished. Continued on next page ... Presented by Opel GT Source www.opelgtsource.com / www.opelgts.com Vol. 1 / Issue #2 By the time the paint was complete, all parts were ready to reinstall on my new Blue GT – (Graduated with undergrad in MIS and began project management) The efforts and coordination were the culmination of planning on my first project. Engine and Suspension (2007 – 2008) An engine overhaul was much needed. Pulled the engine with help from a mutual friend who owned a repair shop. Once on the engine stand, I found three cylinders with 65 lbs. and one with 92 lbs. of compression. This engine required a complete overhaul. Newbies in the rebuild included Glyco bearings, and higher lift performance CAM, rings, and a full gasket set. This was coupled with my earlier work in the 1990’s: Weber DGAS, and Crane CAMS electronic ignition. Some suspension work included polyurethane bushings, and a lower transverse leaf spring for the front end. This was coupled with existing anti-sway bars installed back in my earlier work in the 1990’s. Interior (2009) Replaced Headliner, seat covers, and new carpet Big Brakes (2011) Euro Master Cylinder – Booster (2012) 1970 GT Specs: Original numbers matching 1900 cc Weber 38 DGAS Carburetor American Racing Turbine Rims with 205-60R 13 Tires Crane CAMS Optical Electronic Ignition Header Exhaust Manifold Turbo Muffler with two Monza big bore resonators “y” pipe Polyurethane front bushings with lowered front end using shorter transverse leaf spring Front and Rear Stabilizer bars GT Grant Steering Wheel with MOMO Adapter Three core radiator with 7 blade Fan 1975 Big brake Rotors and Calipers 22 mm Bore European Master Cylinder 9” diameter brake booster Presented by Opel GT Source www.opelgtsource.com / www.opelgts.com Vol. 1 / Issue #2 Upcoming Opel Events: At just $199 plus shipping, it’s a real bargain too! Easy 15 minute installation and No core required. 1. We are also working on a new production of CIH rocker arm studs and rocker arm nuts which we will have in stock in the coming months. 2. 3. 4. 5. 6. April 16, 2016: NorCal Opel Fun Run: ending with a with BBQ at OGTS. Attend the fun run and or just join us in the afternoon for the BBQ/potluck. Info: Mike Meier mlmeier@kstreetstudio.com or Gil at 209-928-1110 for details / rsvp. May 20-22, 2016 Carlisle Opel Nationals: Celebrating it’s 20th anniversary of Opel’s in attendance. Come out and meet Gil in person. June ? OMC Picnic, TBA watch for next issue. July ? Yosemite Fun Run & Photo Shoot: typically 2nd weekend of July weather permitting. TBA July 30, Opel’s of Washington. Kelley’s Kafe, 16302 Pacific Ave South, Spanaway, Washington (Info: contact John at 253-581-5372 October? We are considering a fun run to Durango, Silverton & Ouray Colorado for the fall colors in 2016. To be confirmed and announced at a later date. Greetings From Gil: If you are into upgrades to your GT interior look, we have a new lower cost, mass production, of the Oil temp/Voltmeter that replaces the clock in your GT instrument panel. It matches the style of the other two instruments and would pass, to the untrained eye, as original. We are now on our second production run of GT stainless steel exhaust systems. They are now finished and will be shipped out of Europe this week. We should have them in March. We have many other projects in the works and will be announced as they are closer to be delivered. Our new “Opel Passion Newsletter” will be published throughout the year for your reading pleasure. We are passionate about classic Opel’s and wish to share that with you via Opel Images, Articles, Tech Tips and Your Opel Stories in our “Across America” column. Another new tool for you … is our new domain/ website: www.opelgts.com Dear Fellow Opel Owners: 2016 looks to be another great year for our Opel’s here in the USA. With more exposure on TV, auctions and car shows the Opel is finally getting some mainstream attention. It also helps that Opel in Germany is debuting it’s new Opel GT concept car at the 2016 Geneva auto show. This has brought the classic GT back in the spotlight as the media reminisces and compares the classic to the new concept car. On the new product development side. We have been busy here at OGTS investing in new products that would otherwise be discontinued. Our new replacement GT steering wheels are finished and those who got the early delivery wheels are sending us very happy feedback with how awesome the new steering wheel has transformed the look and feel of the interior. If you have not ordered one yet, you need to. It is your direct hands on connection to your GT and the new wheel not only looks amazing, but the feel of the new wheel is fantastic! Our production will be arriving in March and we have a few of the original style in stock ready for immediate shipping. Across America Column: We consider anyone driving a classic Opel these days are unique and has a story to share of their Opel(s), so please submit them to rich@opelgtsource.com for consideration. We thank you for choosing Opel GT Source to fulfill your Opel passion! Maintaining the Marque, Gil Wesson Opel GT Source Continued in next column ... Presented by Opel GT Source www.opelgtsource.com / www.opelgts.com Vol. 1 / Issue #2 OPEL TECH TIP: “A bright idea that you will get a charge from!” Tools required: 8mm nut driver or socket. Dremel with brass wire brush, or equiv. It’s all about current flow! Think of the alternator as the heart in our Opel’s and the fuse box as the main artery system. If our artery system is not clean and is filled with oxidation / corrosion … then many components will not work as they are intended to. Procedure: Disconnect (+) battery cable from Battery. Using an 8mm nut driver, remove 1 nut and washer then the associated wire from the terminal block. Remove the 2nd nut and washer and proceed to remove all the oxidation from the nuts, wire connection lug, terminal stud, and underlying terminal strip connector. Once oxidation is removed, reassemble in reverse order of disassembly and ensure each washer and nut are securely tightened to provide a solid contact. The effects of oxidation / corrosion in our fuse box causes voltage drops that lead to: 1. 2. 3. 4. Improper battery charging Inaccurate gauge readings Dimmer headlights Inconsistent turn signal indicator function Repeat this for the next 3 terminals. Location: Fuse box is located on the drivers side foot well above your left knee when seated. Reconnect battery when finished. You should see the improvements right away. Note: Cleaning each fuse contact and fuse end connec- tion would be the next step, followed by each quick slide connection (replacing any cracked or broken connectors on wires where needed). Cleaning the contacts on the ammeter terminals, nuts and wire connections are also very important. You can take on these cleaning projects as needed. Feel free to go through ALL the electrical connections and remove oxidation and corrosion, including all the light bulbs and sockets too! (Notice corrosion and oxidation typical for this area. Shown prior to cleaning) To improve current flow: start with the 4 main electrical studs in the middle of the fuse block terminal as shown in this image. This is where the power enters the system from the battery/ starter and then splits off to the ammeter and back to the fuse block. Continued in next column ... Presented by Opel GT Source www.opelgtsource.com / www.opelgts.com Vol. 1 / Issue #2
Similar documents
May June 08 Blitz - Opel Motorsports Club
Last month Tom Esterkin mailed me a photocopy of an article from Automobile magazines ‘Ignition’ column, written by Jamie Kitman and entitled, ‘Domestic carmakers took their eye off the ball. It’s ...
More informationFight The Future - Opel Motorsports Club
7 speakers stereo with integrated navigational system with 7” Display - Roof Antenna 19” wheels standard w/ 245/40/19 - Brembo calipers with 355 mm vented and cross drilled rotors Driver/Passenger ...
More information