4 - Groz Tools

Transcription

4 - Groz Tools

www.groz-tools.com
1500 DEVOTED MEN WORK TIRELESSLY
IN OVER 500,000 SQ.FT STATE-OF-THE-ART
GROZ MANUFACTURING FACILITIES
JUST TO GIVE YOU
A GOOD NIGHT'S REST
call +91.124.282.7777 or mail to info@groz-tools.com
Anyone can make tools. Many can even make good tools. But if
you are looking for peace of mind that comes with the assurance
that your specifications will be adhered to, your deadlines will be
bettered and that you can communicate with people in a language
that you understand, your choices are surely limited. For those
who have been in the business long enough to know the facts,
Groz is the natural choice. That is because we deliver hassle-free
solutions. Rest assured.
Tools to trust. Since 1976.
ADDITIONS
Dear Valued Customer,
It is my pleasure to present to you
our latest Professional Hand Tools
catalogue.
We have covered fair ground over
the last few years and with our
new state-of-the art production
facility, we can now do much more
than before. You will see many new
technologically superior products
as well as modifications to some of
the earlier designs, in the following
pages. Further, I assure you of the
same top performance to which
you are accustomed to from Groz.
We appreciate your business and
value your loyalty & trust.
Warm Regards,
15
Roll
Pin
Punches
15
Hinge
Centring
Punch
18
Hollow
& Arch
Punches
32
Chisel &
Bolster
Merchandisers
32
Engineer's
Steel Bench
Vice
58
Bench
Planes
60
DuplexRabbet
& Fillister
Plane
66
Woodworking
Front Vice
67
KWIK Action
Woodworking
Clamps
74
Wing
Compass
78
Tap & Reamer
Wrenches Industrial
89
CAT /
Aligning
Bars
ANIL BAMMI
Managing Director
96
Grommet
Kits
CB02 PRO HAND TOOLS
1
Punches & Chisels
08
10
14
14
15
15
16
16
17
Centre Punches
Pin Punches
Starting Punches
Drift Punches
Roll Pin Punches
Hinge Centring Punches
Prick Punches
Nail Punches
Automatic Centre Punches
18
20
21
22
25
25
26
28
32
Hollow & Arch Punches
Steel Stamps
About Chisels
Cold Chisels
Wrecking Bars
Brick Layer's Line Pins
Brick Bolsters
Punch & Chisel Kits
Chisel & Bolster Merchandisers
34
35
36
37
38
39
40
Professional Mechanic's Vices
Engineer's Steel Bench Vices
Drill Press Vices - Unigrip
DIY Drill Press Vices
Reversible Vice
Hobbyist Vices
Hand Vices
40
41
42
43
44
44
Anvils - Cast Steel
G Clamps - General Purpose
G Clamps - Drop Forged
G Clamps - Heavy Duty
G Clamps - Junior
G Clamps - Hobbyist's
46
47
48
49
51
52
Handyman's Hacksaw
Hacksaw Frame - Professional
Universal Saw
Junior Saw Frames
Piercing Saw Frames
Coping Saw Frames
53
54
54
55
55
56
Fret Saw Frames
Hacksaw Blades
Piercing Saw Blades
Fret Saw Blades
Coping Saw Blades
Mini Saw Blades
2
Vices & Clamps
3
Hacksaws & Blades
www.groz-tools.com
info@groz-tools.com
Whilst every effort has been made to ensure accuracy of information
given in this catalogue at the time of going to print, March 2008, our
policy of continuous improvement determines the right to change
specifications without notice. Customers must ensure that goods are
suitable for the purpose intended.
© Groz Engineering Tools (P) Ltd., 2008
The Groz name, symbol and logo are registered trademarks
Imperial dimensions shown as equivalent to metric sizes are
approximate and vice versa.
4
Woodworking
58
60
61
62
63
64
65
Bench Planes
Duplex Rabbet & Fillister Plane
Block Planes
Woodworking Vice - Plain Screw
Woodworking Vice - Portable
WoodworkingVice - Quick Release
Woodworking Vice - Rapid Action
66
67
68
69
69
70
70
Woodworking Front Vice
KWIKActionWoodworkingClamps
Rapid Action I Bar Clamps
Duo Bar Clamps
Cramp Head Set
Sash Bar Clamps
T Bar Clamps
Spring Dividers & Calipers
Craftsmen's Dividers & Calipers
Wing Compass
Adjustable Bevel
75
75
76
76
Centre Square
Precision Woodworker's Squares
Brass Calipers
Steel Rules
5
Measuring & Marking
72
73
74
74
6
Taps, Dies & Holders
78 AdjustableTap&ReamerWrenches
79 Tap Wrenches - T Handle Type
80 Die Stock Holders for Round Dies
81 Tap & Die Sets
82 Hand Taps - Carbon Steel
84 Dies - Carbon Steel
89 Roll Head Pry Bars
89 CAT / Aligning Bars
90 Wheel Wrenches Double Ended
90 Ring Slogging Wrenches
91 Box Spanners (Box Wrenches)
92 Brass Hammers
94 Paint Mixer
94 Revolving Punch Pliers
95 Metal Bender
96 Hobbyisit's Anvils
96 Grommet Kits
7
Automotive
8
DIY
www.groz-tools.com
1
Center Punches 8 Pin Punches 10 Starting Punches 14 Drift Punches 14 Roll Pin Punches 15
Hinge Centering Punch 15 Prick Punches 16 Nail Punches 16 Automatic Centre Punches 17
Hollow & Arch Punches 18 Steel Stamps 20 Cold Chisels 22 Wrecking Bar 25
Bricklayer's Line Pins 25 Bolsters 26 Punch & Chisel Kits 28 Chisel & Bolsters
- Merchandiser Packs 32
01 CENTRE PUNCHES <No. 251, No. 252>
Centre Punches — Heavy Duty <No. 252>
esp Granetes de trazar
frPointeau
deKörner
Single piece construction with hexagonal shank, these are amongst the
strongest and most durable of Centre Punches. Working ends are accurately
ground and the punch body is in premium powder coated finish.
Centre Punches are manufactured from selected carbon steel. These
are accurately hardened and tempered so that the point will withstand
continuous use and the striking end will not splinter. These are ideal for
clearly marking metal in work layout & making indentations in a work piece
before drilling to ensure correct location of drill points.
Cat.Nr.
The working tips are centered and ground to the correct angle
(90o included angle) for increased efficiency in marking. The
striking end is chamfered to prevent breakage.
Ordering
Nr.
Point Size (P)
Stock Size
Overall Length (L)
Inch
mm
Inch
mm
Inch
mm
CP/HD/5-64
25200
5/64
2
1/4
6
3.1/2
90
CP/HD/1-8
25201
1/8
3
5/16
8
4.1/4
108
uCP/HD/5-32
25202
5/32
4
3/8
10
5
125
25206
5/32
4
5/16
8
5.1/2
138
CP/HD/5-32/SPL
uCP/HD/1-4
90o
These are available in 3 types:
Centre Punches - Heavy Duty <No. 252>
Centre Punches - Round Head <No. 251>
Centre Punches - Square Head <No. 251>
25203
1/4
6
1/2
12
6
150
CP/HD/1-4/SPL
25207
1/4
6
3/8
10
6
150
CP/HD/3-8
25204
3/8
10
5/8
16
6.1/4
160
Sets
CP/HD/5/ST
u
25205
A set of 5 Centre Punches containing one each of
5/64" (2mm), 1/8" (3mm), 5/32" (4mm), 1/4" (6mm) &
3/8" (10mm) packed in a vinyl pouch.
BESTSELLER
UTILITY
P
automotive
52-58
HRC
industrial
l
HeavyDuty> CP/HD/5/ST
A set of 5 Centre Punches
containing one each of
5/64" (2mm), 1/8"(3mm),
5/32"(4mm), 1/4" (6mm)
& 3/8" (10mm) packed in a
vinyl pouch
CB 2
section 1
Centre Punches — Round Head <No. 251>
Centre Punches — Square Head <No. 251>
Single piece construction with round shank and round striking head. The
knurling is clean and well cut to provide a positive finger grip. This range of
punches have a rust inhibiting black oxide finish
Two piece construction with round shank and square striking head. Clean
cut knurling on the shank provides a positive finger grip. The 3/8" (9.5 mm)
square head provides a larger area for striking & also prevents the punch
from rolling off. This range of punches have rust inhibiting black oxide finish
Cat.Nr.
Ordering
Nr.
Point Size (P)
Body Diameter
Inch
mm
Inch
mm
Overall Length (L)
Cat.Nr.
Ordering
Nr.
Point Size (P)
Body Diameter
Overall Length (L)
Inch
mm
CP/1-16
25100
1/16
1.5
1/4
6
3
75
uCP/5-64
25101
5/64
2
5/16
8
4
100
CP/SQ/1-16
CP/3-32
25102
3/32
2.5
5/16
8
4
100
CP/SQ/3-32
CP/1-8
25103
1/8
3
5/16
8
4
100
CP/9-64
25104
9/64
3.5
5/16
8
4
100
CP/SQ/5-32
25153
5/32
4
9/32
7
4
100
uCP/5-32
25105
5/32
4
3/8
10
4
100
uCP/SQ/3-16
25154
3/16
5
9/32
7
4
100
uCP/SQ/1-4
CP/3-16
25106
3/16
5
3/8
10
4
100
CP/7-32
25107
7/32
5.5
3/8
10
4
100
25108
1/4
6
7/16
11
5
125
25111
1/4
6
1/2
13
5
125
uCP/1-4
CP/1-4/SPL
CP/SQ/3-16L
(Extra long
Punch)
u
Sets
uCP/5/ST
uCP/SQ/1-8
25109
A Set of 5 Centre Punches in sizes 1/16"(1.5mm), 5/64"
(2mm), 3/32" (2.5mm), 9/64"(3.5mm) & 5/32"(4mm) packed
in a vinyl pouch
CP/5/1-8/ST
25110
A Set of 5 Centre Punches in sizes 1/16" (1.5mm),
5/64"(2mm), 3/32"(2.5mm), 1/8"(3mm) & 5/32"(4mm)
packed in a vinyl pouch.
uCP/8/WD/ST
25120
A Set of 8 Centre Punches in sizes 1/16"(1.5mm), 5/64"
(2mm), 3/32" (2.5mm), 1/8"(3mm), 9/64"(3.5mm), 5/32"
(4mm), 3/16"(5mm) & 7/32"(5.5mm) packed to a wooden box
Inch
mm
Inch
mm
Inch
mm
25150
1/16
1.5
9/32
7
4
100
25151
3/32
2.5
9/32
7
4
100
25152
1/8
3
9/32
7
4
100
25155
1/4
6
3/8
9.5
4
100
25156
3/16
5
13/32
10.5
6.1/2
165
BESTSELLER
P
52-58
HRC
l
UTILITY
industrial
RoundHead> <SquareHead CP/8/WD/ST
A Set of 8 Centre Punches in sizes
1/16"(1.5mm),5/64"(2mm),3/32"(2.5mm),
1/8"(3mm), 9/64"(3.5mm), 5/32" (4mm),
3/16"(5mm) & 7/32" (5.5mm) packed to a
wooden box
CP/5/ST
A Set of 5 Centre Punches in
sizes1/16"(1.5mm),5/64"(2mm),
3/32"(2.5mm),9/64"(3.5mm)&
5/32"(4mm) packed in a vinyl
pouch
CB 3
section 1
02 PIN PunchES <No. 256P>
esp Botadores cilindricos
frChasse-goupilles
deSplinttreiber
Pin Punches are manufactured from high quality carbon steel, accurately
hardened and tempered so that the Pin will withstand continuous use and
the striking end will not splinter. These are induction hardened to ensure
consistent hardness and a special tempering process prevents the head
from fracturing, thereby preventing accidents.
1. Pin Punches - Heavy Duty
2. General Purpose Round Shank Pin Punches
Pin Punches – Heavy Duty <No. 256P>
Single piece construction with hexagonal shank. Single piece construction
imparts additional durability to the punch. Working ends are accurately
ground and the punch body is in premium powder coated finish.
Cat.Nr.
Ordering Pin Diameter (D)
Nr.
Inch
mm
Stock Size
Overall Length (L)
Inch
mm
Inch
mm
PP/HD/1-16
25600
1/16
1.5
1/4
6
4
100
uPP/HD/3-32
25601
3/32
2.5
5/16
8
4.1/2
112
25609
3/32
2.5
1/4
6
4.1/4
106
uPP/HD/1-8
PP/HD/3-32/SPL
25602
1/8
3
5/16
8
4.3/4
119
uPP/HD/5-32
25603
5/32
4
5/16
8
5
125
uPP/HD/3-16
25604
3/16
5
3/8
10
5.1/4
132
PP/HD/3-16/SPL
25610
3/16
5
5/16
8
5.1/4
132
PP/HD/7-32
25605
7/32
5.5
3/8
10
5.1/2
138
25606
1/4
6
3/8
10
5.3/4
145
PP/HD/5-16
25607
5/16
8
7/16
11
6
150
PP/HD/3-8
25608
3/8
10
1/2
12
6.1/2
163
UTILITY
uPP/HD/1-4
automotive
Sets
industrial
Pin Punches are used for driving out
andremovingalreadyloosenedpins&
keys after initial movement by a solid
or starting punch
PP/HD/6/ST
25612
A set of 6 Pin Punches containing one each 3/32" (2.5mm),
1/8"(3mm), 5/32"(4mm), 3/16"(5mm), 1/4"(6mm) & 5/16"
(8mm), packed in a vinyl pouch
uPP/HD/7/ST
25611
A set of 7 Pin Punches containing one each of 1/16" (1.5mm),
3/32" (2.5mm), 1/8"(3mm), 5/32"(4mm), 3/16" SPL (5mm),
7/32"(5.5mm) & 1/4"(6mm), packed in a vinyl pouch
u
BESTSELLER
D
52-58
HRC
CB 4
l
section 1
Extra Long Pin Punches - Heavy Duty <No. 256P>
The extra Long Pin Punches are useful for all applications where added
leverage is required.
Cat.Nr.
Ordering
Nr.
Pin Diameter (P)
Stock Size
Overall Length (L)
Inch
mm
Inch
mm
Inch
mm
uPP/HD/1-8L
25650
1/8
3
5/16
8
8
200
uPP/HD/3-16L
25651
3/16
5
3/8
10
8
200
uPP/HD/1-4L
25652
1/4
6
3/8
10
8
200
PP/HD/5-16L
25653
5/16
8
7/16
11
8
200
PP/HD/3-8L
25654
3/8
10
1/2
12
8
200
Sets
PP/HD/5L/ST
u
25655
PP/HD/6/ST
A set of 6 Pin Punches containing one
each of 3/32" (2.5mm), 1/8"(3mm),
5/32"(4mm), 3/16"(5mm), 1/4"(6mm) &
5/16"(8mm), packed in a vinyl pouch
A set of 5 extra long Pin Punches containing one each of
1/8" (3mm), 3/16"(5mm), 1/4"(6mm), 5/16"(8mm) & 2-3/8"
(10mm) packed in a vinyl pouch
BESTSELLER
D
52-58
HRC
l
PP/HD/5L/ST
A set of 5 extra long Pin Punches
containing one each of 1/8" (3mm),
3/16"(5mm),1/4"(6mm),5/16"(8mm)
&3/8"(10mm)packedinavinylpouch
CB 5
section 1
PIN PunchES <No. 255>
General Purpose Round Shank Pin Punches
These round shank pin punches have clean and well cut knurling which
provides positive, non slip grip. This range of punches has rust inhibiting
black oxide finish. These are available in 3 different lengths:
Pin Punches 4" (100 mm) long:
Single piece construction with 1" (25 mm) long pin.
Single piece construction with 1.3/4" (45 mm) long pin.
Pin Punches — 4" (100 mm long)
Cat.Nr.
UTILITY
Body Diameter
Inch
mm
Inch
mm
25560
1/16
1.5
9/32
7
PP/3-32
25561
3/32
2.5
9/32
7
uPP/1-8
25562
1/8
3
9/32
7
uPP/5-32
25563
5/32
4
9/32
7
uPP/3-16
25564
3/16
5
5/16
8
PP/7-32
25565
7/32
5.5
5/16
8
25566
1/4
6
3/8
10
25567
5/16
8
7/16
11
uPP/1-4
Sets
uPP/4/ST
25568
A Set of 4 Pin Punches containing one each of
1/8"(3mm), 5/32"(4mm), 3/16"(5mm) &1/4"(6mm)
packed in vinyl pouch.
PP/8/ST
25569
A Set of 8 Pin Punches containing one each of 1/16"
(1.5mm), 3/32"(2.5mm), 1/8"(3mm), 5/32"(4mm),
3/16"(5mm), 7/32"(5.5mm), 1/4"(6mm) & 5/16"(8mm)
25580
A Set of 8 Pin Punches containing one each of 1/16"
(1.5mm), 3/32"(2.5mm), 1/8"(3mm), 5/32"(4mm),
3/16"(5mm), 7/32"(5.5mm), 1/4"(6mm) & 5/16"(8mm)
packed in a wooden box.
uPP/8/WD/ST
u
industrial
Pin Diameter (D)
uPP/1-16
PP/5-16
Two piece construction with a 3.3/4" (90 mm) long pin. The two piece
construction allows the pin to have a separate hardness from the body
which prevents “peening” and also ensures complete straightness over such
a long length.
Ordering
Nr.
BESTSELLER
D
l = 6" (150 mm)
D
l = 4" (100 mm)
CB 6
section 1
Cat.Nr.
Ordering
Nr.
Pin Diameter (D)
Body Diameter
Inch
mm
Inch
mm
Cat.Nr.
Ordering
Nr.
Pin Diameter (D)
Body Diameter
Inch
mm
Inch
mm
PPR/1-16
25540
1/16
1.5
9/32
7
DDP/1-16
25500
1/16
1.5
23/64
9
uPPR/3-32
25541
3/32
2.5
9/32
7
DDP/3-32
25501
3/32
2.5
3/8
10
PPR/1-8
25542
1/8
3
9/32
7
25502
1/8
3
3/8
10
uPPR/5-32
25543
5/32
4
9/32
7
DDP/5-32
25503
5/32
4
3/8
10
uPPR/3-16
25544
3/16
5
5/16
8
uDDP/3-16
25504
3/16
5
1/2
12
PPR/7-32
25545
7/32
5.5
5/16
8
uDDP/1-4
25505
1/4
6
1/2
12
uPPR/1-4
uDDP/1-8
25546
1/4
6
3/8
10
uDDP/5-16
25506
5/16
8
1/2
12
PPR/5-16
25547
5/16
8
1/2
12
DDP/3-8
25507
3/8
9.5
1/2
12
PPR/3-8
25548
3/8
9.5
1/2
12
Sets
Sets
uPPR/6/ST
PPR/8/ST
25549
25550
A Set of 6 Pin Punches containing one each of
3/32" (2.5mm),1/8"(3mm), 5/32"(4mm), 3/16"
(5mm), 1/4"(6mm), & 5/16"(8mm) packed in
vinyl pouch
A Set of 8 Pin Punches containing one each
of 1/16"(1.5mm), 3/32"(2.5mm), 1/8"(3mm),
5/32"(4mm), 3/16"(5mm), 7/32"(5.5mm), 1/4"
(6mm) & 5/16"(8mm) packed in a vinyl pouch
uDDP/5/ST
25508
A Set of 5 Pin Punches in sizes 1/8" (3mm),
3/16"(5mm), 1/4"(6mm), 5/16"(8mm) &
3/8"(9.5mm) packed in a vinyl pouch
uDDP/8/ST
25509
A Set of 8 Pin Punches in sizes 1/16"(1.5mm),
3/32"(2.5mm), 1/8"(3mm), 5/32"(4mm),
3/16"(5mm) 1/4"(6mm), 5/16"(8mm) & 3/8"
(9.5mm) packed in a vinyl pouch
u
BESTSELLER
PP/8/WD/ST
D
l = 8" (200 mm)
A Set of 8 Pin punches
containingoneeachof1/16"
(1.5mm), 3/32"(2.5mm),
1/8"(3mm), 5/32"(4mm),
3/16"(5mm), 7/32"(5.5mm),
1/4"(6mm) & 5/16"(8mm)
packed in a wooden box.
PPR/6/ST
A Set of 6 Pin Punches
containing one each of
3/32"(2.5mm), 1/8"(3mm),
5/32"(4mm), 3/16"(5mm),
1/4"(6mm), & 5/16"(8mm)
packed in vinyl pouch
DDP/8/ST
A Set of 8 Pin punches
in sizes 1/16"(1.5mm),
3/32"(2.5mm), 1/8"(3mm),
5/32"(4mm),
3/16" (5mm), 1/4"(6mm),
5/16"(8mm) & 3/8" (9.5mm)
packed in a vinyl pouch
CB 7
section 1
03 Starting Punches <No. 257>
04 Drift Punches <No. 258>
esp Botadores Conico
frPoincon
deSplinttreiber
esp Botadores Conico
frPoincon
deDurchschläger
These Punches are used as a starting tool prior to using Pin Punches, as
they are useful for loosening frozen or tight pins and keys, or knocking
out rivets. These have a single piece construction with hexagonal shank.
Manufactured from selected carbon steel, they are accurately hardened for
extended service life. The working ends are machine ground with the body
in premium powder coated finish.
Manufactured from selected carbon steel, these have a single piece
construction. Punches are accurately hardened and tempered for increased
working life. The working ends are machine ground with the body in
premium powder coated finish.
Cat.Nr.
Ordering
Nr.
Tip Diameter (D)
Stock Size
Drift Punches are ideal for lining up holes in 2 or more pieces of metal and
for drawing pins through various assemblies. These are also referred to as
“Alignment Punches”.
Overall Length (L)
Inch
mm
Inch
mm
Inch
mm
SGP/HD/1-16
25700
1/16
1.5
3/8
10
5
125
SGP/HD/3-32
25701
3/32
2.5
3/8
10
5
125
SGP/HD/1-8
25702
1/8
3
3/8
10
5
125
SGP/HD/1-8/SPL
25720
1/8
3
5/16
8
5
125
SGP/HD/5-32
25703
5/32
4
3/8
10
5
125
SGP/HD/3-16
25704
3/16
5
3/8
10
5
125
SGP/HD/7-32
25705
7/32
5.5
3/8
10
5.1/2
140
SGP/HD/1-4
25706
1/4
6
3/8
10
5
125
SGP/HD/5-16
25707
5/16
8
1/2
12
6
150
SGP/HD/3-8
25708
3/8
9.5
5/8
16
6.1/2
165
SGP/HD/1-2
25709
1/2
12
5/8
16
7
175
D
52-58
HRC
l
Cat.Nr.
Ordering
Nr.
Tip
Diameter (D)
Stock
Size
Overall
Length (L)
Inch
mm
Inch
mm
Inch
mm
DFP/HD/3-32
25800
3/32
2.5
5/16
8
8
200
u
DFP/HD/1-8
25801
1/8
3
5/16
8
8
200
u
DFP/HD/5-32
25802
5/32
4
3/8
10
9
225
u
DFP/HD/5-32/SPL
25822
5/32
4
1/2
12
10
250
u
DFP/HD/3-16
25803
3/16
5
1/2
12
10
250
DFP/HD/3-16/SPL
25820
3/16
5
5/16
8
10
250
DFP/HD/7-32
25804
7/32
5.5
1/2
12
10
250
DFP/HD/7-32/SPL
25823
7/32
5.5
3/4
19
17.3/4
450
DFP/HD/1-4
25805
1/4
6
5/8
16
12
300
DFP/HD/1-4/SPL
25821
1/4
6
3/8
10
10
250
DFP/HD/5-16
25806
5/16
8
3/4
19
12
300
DFP/HD/3-8
25807
3/8
9.5
3/4
19
15
375
DFP/HD/3-8/SPL
25824
3/8
9.5
5/8
16
10
250
DFP/HD/1-2
25808
1/2
12
7/8
22
18
450
u
Sets
DFP/HD/7/ST
UTILITY
25809
A set of 7 Drift Punches in sizes 1/8"(3mm),
5/32"(4mm),3/16"(5mm), 7/32"(5.5mm)
1/4"(6mm),5/16"(8mm),& 3/8"(10mm)
u
automotive
BESTSELLER
Underlined
sizes find use
in construction
for aligning
scaffoldings
industrial
UTILITY
l
automotive
industrial
D
52-58
HRC
DFP/HD/7/ST
A set of 7 Drift Punches in
sizes 1/8" (3mm), 5/32"
(4mm), 3/16" (5mm),
7/32"(5.5mm), 1/4"(6mm),
5/16"(8mm) & 3/8"(9.5mm)
CB 8
Insert the punch into the hole,
pry or twist both into alignment.
Tapping gently with the long well
formed taper will ensure that the
holes are in perfect alignment.
section 1
05 RollPinPunches <No.256R>
06 HingeCenteringPunch
esp Botadore cilindricos
fr Chasse - goupilles
deSplinttreiber
esp Granetes de trazar
frPointeau
deKörner
Single piece construction with hexagonal shank imparts additional durability.
Body has a premium powder coated finish with chamfered striking end that
helps reduce mushrooming & chipping.
Hinge Centering Punches are used for starting and centering screw holes
when attaching countersunk hardware such as hinges, hangars, hasps,
brackets, locks and drawer pulls.
These precision-machined roll pin punches are specifically designed to
remove spring pins / roll pins. The heat –treated point has a rounded ball
to center the point into the pin allowing the point shoulder to maintain
maximum contact with the pin during removal and eliminating any damage
to the pin or wall
Punch has a spring action with a hardened steel pin for convenient marking.
The taper end of the punch ensures starting hole is correctly centered in the
screw hole.
Ideal accessory for close quarter drilling
Cat.Nr.
Cat.Nr.
RPP/3-32
RPP/1-8
u
u
Ordering
Nr.
25640
25641
Ball Diameter (D)
Stock Size
Overall Length (L)
Inch
mm
Inch
mm
Inch
mm
3/32
1/8
2
3
1/4
1/4
6
6
3.1/2
3.3/4
89
94
RPP/5-32
25642
5/32
4
5/16
8
4.1/2
114
RPP/3-16
25643
3/16
5
5/16
8
4.1/2
114
RPP/1-4
25644
1/4
6
3/8
10
5.1/2
140
RPP/5-16
25645
5/16
8
3/8
10
6
150
RPP/6/ST
25646
A Set of 6 Roll Pin punches containing one each of
3/32"(2.5mm), 1/8"(3mm), 5/32"(4mm), 3/16"(5mm),
1/4"(6mm) & 5/16"(8mm) packed in a vinyl pouch
JCP/01
Ordering
Nr.
25004
Stock Size
Overall Length
Inch
mm
Inch
mm
3/8
10
2-1/2
63
UTILITY
Spring
loaded
woodworking
BESTSELLER
D
l
UTILITY
automotive
industrial
Roll Pin Punch being used to
remove spring pin from a gun
Punchbeingused
to mark screw
starting centres
on a door frame
CB 9
section 1
07 prick Punches <No. 254>
08 NAIL Punches <No. 253>
esp Punzon punta-labores pesados
fr Pointeau de tracage
deAnreißnadeln
esp Botadores para puntas
frChasse-clous
deNagelversenker
Prick Punches are used for marking metals in work layouts.
These punches have a very sharp point
(60° included angle), hence are highly suitable where very
precise marking / scorring is required. These have a single
60
piece construction with hexagonal shank. Manufactured
from selected carbon steel, they are accurately hardened for
extended service life. The working ends are machine ground with the body in
premium powder coated finish.
Nail Punches are manufactured from selected carbon steel, accurately
hardened and tempered for increased service life. Clean-cut knurled round
shank provides a positive non-slip grip. The 3/8" (9.5 mm) square head
provides a larger striking area and also prevents the punch from rolling off.
The striking end is chamfered to prevent breakage. This range of punches
has a black oxide finish.
o
Cat.Nr.
u
Ordering
Nr.
Point Size (P)
Stock Size
Inch
mm
Inch
mm
Overall Length (L)
Inch
mm
PKP/HD/1-4
25450
5/64
2
1/4
6
3
75
PKP/HD/3-8
25451
5/32
4
3/8
10
5
125
PKP/HD/1-2
25452
1/4
6
1/2
12
6
150
P
52-58
HRC
Nail Punches are designed for driving nail heads below the surface of
wood. The working end is cupped to follow the nail head without sliding off.
These can also be used to remove nails that have an exposed point. Place
the recessed tip against the point of the nail and strike the punch with a
hammer to back the nail out of the hole.
Cat.Nr.
Ordering
Nr.
Tip Diameter
Overall Length
Inch
mm
Inch
mm
u
NLP/SQ/1-32
25360
1/32
0.80
4
100
u
NLP/SQ/1-16
25361
1/16
1.5
4
100
u
NLP/SQ/3-32
25362
3/32
2.5
4
100
u
NLP/SQ/1-8
25363
1/8
3
4
100
NLP/SQ/5-32
25364
5/32
4
4
100
NLP/SQ/3-16
25365
3/16
5
4
100
l
Set
NLP/SQ/3/ST
UTILITY
u
25366
A set of 3 Nail Punches in sizes 1/32"
(0.80mm), 1/16"(1.5mm) & 3/32"(2.5mm)
BESTSELLER
UTILITY
automotive
woodworking
52-58
HRC
industrial
NLP/SQ/3/ST
A set of 3 Nail Punches
in sizes 1/32" (0.80mm),
1/16"(1.5mm)&3/32"(2.5mm)
CB 10
section 1
09 Automatic Centre Punches <ACP-1, ACP-H2, MP-88>
Automatic Centre Punch – Light Duty <ACP-1>
esp Granetes automatico
fr Pointeau a dispositif de frappe incorpore
de Automatischer Körner
Useful for light marking jobs.
Cat.Nr.
Groz manufactures a complete range of fully automatic single hand
operated spring loaded punches, wherein the built in mechanism delivers a
punch just with the pressing of the head.
The depth of the impression is variable and can be adjusted from light
marking to heavy blows by turning the knurled head. Screwing the cap
downwards produces heavy indentation; progressively lighter marking can
be obtained by screwing the cap upwards. Once the knurled cap is set to the
desired position, the punch will strike the same depth every time.
u
ACP/1B
25000
Body Diameter
Overall Length (L)
Inch
mm
Inch
mm
1/2
13
4.3/4
120
AutomaticCentrePunch–HeavyDuty <ACP-H2>
A heavy-duty version of the above punch. It is capable of making
very deep indentations.
These have a round shank with clean and well cut knurling for positive nonslip grip. Tips are made from hardened tool steel and can be easily removed
for re-sharpening or replacement.
These are available in three types:
1. Automatic Centre Punch - Light Duty <ACP-1>
2. Automatic Centre Punch - Heavy Duty <ACP-H2>
3. Marking Punch <MP-88>
Ordering
Nr.
Cat.Nr.
Ordering
Nr.
Body Diameter
Inch
mm
Overall Length (L)
Inch
mm
ACP/H-2
25010
23/32
18
5.3/4
146
STP/ACP/H2 (Spare tip)
25011
-
-
-
-
Marking Punch <MP-88>
A heavy duty punch with a single piece point and shank.
P
52-58
HRC
Cat.Nr.
l
Ordering
Nr.
MP/88
Spring
loaded
u
25020
Body Diameter
Overall Length (L)
Inch
mm
Inch
mm
5/8
16
6.13/64
157
BESTSELLER
UTILITY
automotive
MP/88 > ACP/1B> ACP/H-2> WARNING
no
hammering
CB 11
section 1
10 hollow & arch Punches
esp Sacabocados cilindricos y puente
frEmporte pieces sable
deHenkellocheisen
These punches are used for punching round
holes in gasket material, leather, rubber, canvas,
cardboard, plastic & other soft material.
Hollow Punches
These have a compact cylindrical construction
& are machined from one piece steel. They are
built only to cut small holes from 3/32" (2 mm)
to 1" (25 mm) diameter
Cat.Nr.
Special design of the cutting edge prevents
jamming of material inside the punch. Cutting
edge is induction hardened for extended
working life.
These are built in two different styles, as
detailed below:
1. Hollow Punches
2. Arch Punches
UTILITY
automotive
Ordering
Nr.
Inch
mm
2
26303
1/8
3
26304
5/32
4
HPL/5
26305
3/16
5
HPL/5.5
26371
7/32
5.5
HPL/6
26306
1/4
6
HPL/7
26307
9/32
7
HPL/8
26308
5/16
8
HPL/9
26309
23/64
9
u
HPL/10
26310
3/8
10
u
BESTSELLER
u
u
u
HPL/2
26302
HPL/3
HPL/4
u
Hole Diameter
3/32
u
40+
_50
HRC
Cat.Nr.
u
u
u
u
Ordering
Nr.
Hole Diameter
Inch
mm
HPL/10.5
26372
13/32
10.5
HPL/11
26311
7/16
11
HPL/12
26312
1/2
12
HPL/13
26313
17/32
13
HPL/14
26314
9/16
14
HPL/15
26315
19/32
15
HPL/16
26316
5/8
16
HPL/17
26317
11/16
17
HPL/18
26318
23/32
18
HPL/19
26319
3/4
19
HPL/20
26320
13/16
20
HPL/21
26321
27/32
21
HPL/22
26322
7/8
22
HPL/23
26323
29/32
23
HPL/24
26324
15/16
24
HPL/25
26325
1
25
HPL/14/ST
< Arch Punches
A set of 14 punches in sizes 1/4"
(6mm),5/16"(8mm),3/8"(10mm),
7/16"(11mm),17/32"(13mm),9/16"
(14mm),5/8"(16mm),3/4”(19mm),
7/8" (22mm), 1" (25mm), 1.3/16"
(30mm), 1.1/4" (32mm), 1.3/8"
(35mm)&1.1/2"(38mm)packedin
a wooden box
<HollowPunches
CB 12
section 1
Arch Punches
Cat.Nr.
As the name suggests, these have an Arch /
Bell Type construction. They are larger in form,
with long shaft for convenient holding.
u
These are built in a range of different hole
diameters all the way from 3/16" (5mm) to
2.3/4" (70 mm)
u
Cat.Nr.
Ordering
Nr.
Hole Diameter
Inch
mm
u
HPL/5/BEL
26400
3/16
5
u
HPL/6/BEL
26401
1/4
6
u
HPL/8/BEL
26402
5/16
8
u
HPL/10/BEL
26403
3/8
10
HPL/11/BEL
26404
7/16
11
HPL/12/BEL
26405
1/2
12
HPL/14/BEL
26406
9/16
14
u
u
u
u
u
u
HPL/16/BEL
26407
5/8
16
HPL/18/BEL
26408
23/32
18
HPL/19/BEL
26409
3/4
19
HPL/21/BEL
26410
27/32
21
HPL/22/BEL
26411
7/8
22
HPL/24/BEL
26412
15/16
24
HPL/25/BEL
26413
1
25
HPL/26
26326
1.1/64
26
HPL/27
26327
1.1/16
27
HPL/28
26328
1.3/32
28
HPL/29
26329
1.1/8
29
HPL/30
26330
1.3/16
30
HPL/31
26331
1.7/32
31
u
Ordering
Nr.
Sets
Hole Diameter
Inch
mm
1.1/4
32
HPL/32
26332
HPL/33
26333
1.5/16
33
HPL/34
26334
1.11/32
34
HPL/35
26335
1.3/8
35
HPL/36
26336
1.13/32
36
HPL/37
26337
1.15/32
37
HPL/38
26338
1.1/2
38
39
HPL/39
26339
1.17/32
HPL/40
26340
1.9/16
40
HPL/41
26341
1.5/8
41
HPL/42
26342
1.21/32
42
HPL/43
26343
1.11/16
43
HPL/44
26344
1.23/32
44
HPL/45
26345
1.25/32
45
HPL/46
26346
1.13/16
46
HPL/47
26347
1.27/32
47
HPL/48
26348
1.7/8
48
HPL/49
26349
1.15/16
49
HPL/50
26350
2
50
HPL/52
26352
2.5/64
52
HPL/54
26354
2.5/32
54
HPL/55
26355
2.3/16
55
HPL/57
26357
2.9/32
57
HPL/58
26358
2.19/64
58
HPL/60
26360
2.3/8
60
HPL/62
26362
2.15/32
62
63
HPL/63
26363
2.1/2
HPL/65
26365
2.9/16
65
HPL/67
26367
2.21/32
67
HPL/68
26368
2.2.-11/16
68
HPL/70
26370
2.3/4
70
Cat.Nr.
Ordering
Nr.
Constituents
HPL/5/ST
26390
A set of 5 Hollow
punches in sizes 3/32"
(2mm), 5/32" (4mm),
1/4"(6mm), 5/16" (8mm)
& 3/8"(10mm) packed in a
vinyl pouch
HPL/5/BEL/ST
26440
HPL/6/ST
26391
HPL/7/ST
26392
HPL/7/BEL/ST
26441
A set of 5 Bell type Arch
(6mm), 3/8" (10mm), 1/2"
(12mm), 5/8" (16mm) &
3/4" (19mm) packed in a
vinyl pouch
A set of 6 Hollow punches
in sizes 3/16" (5mm), 1/4"
(6mm), 5/16" (8mm), 3/8"
(10mm), 7/16" (11mm) &
1/2" (12mm) packed in a
vinyl pouch
A set of 7 punches in
sizes 1/2" (6mm), 5/16"
(8mm), 3/8" (10mm), 7/16"
(11mm), 17/32" (13mm),
5/8" (16mm) & 3/4"
(19mm) packed in a plastic
pouch
(6mm), 3/8" (10mm), 1/2"
(12mm), 5/8" (16mm),
3/4" (19mm), 7/8" (22mm)
& 1" (25mm) packed in a
vinyl pouch
HPL/7A/BEL/ST
26442
u
HPL/10/ST
26395
u
HPL/14-ST
26396
sizes 1/4" (6mm), 5/16"
(8mm), 3/8" (10mm),
7/16" (11mm), 17/32"
(13mm), 9/16" (14mm),
5/8" (16mm), 3/4” (19mm),
7/8" (22mm), 1" (25mm),
1.3/16" (30mm), 1.1/4"
(32mm), 1.3/8" (35mm) &
1.1/2" (38mm) packed in a
wooden box
HPL/16/ST
26397
sizes 1/4" (6mm), 5/16"
(8mm), 3/8" (10mm),
7/16" (11mm), 17/32"
(13mm), 9/16" (14mm),
5/8" (16mm), 3/4" (19mm),
7/8" (22mm), 1" (25mm),
1.3/16" (30mm), 1.1/4"
(32mm), 1.3/8” (35mm),
1.1/2” (38mm), 1.25/32”
(45mm) & 2” (50mm)
packed in a wooden box
u
u
HPL/7/BEL/ST
punchesinsizes1/4"(6mm),
3/8" (10mm), 1/2" (12mm),
5/8" (16mm), 3/4" (19mm),
7/8" (22mm) & 1" (25mm)
HPL/10/ST
A set of 10 Hollow punches in sizes
1/4" (6mm), 5/16" (8mm), 3/8" (10mm),
7/16"(11mm),17/32"(13mm),9/16"(14mm),
5/8" (16mm), 3/4" (19mm), 7/8" (22mm) &
1" (25mm) packed in a vinyl pouch
CB 13
HPL/6/ST
A set of 6 Hollow punches
in sizes 3/16" (5mm), 1/4"
(6mm), 5/16" (8mm), 3/8"
(10mm),7/16"(11mm)&1/2"
(12mm) packed in a pouch
(5mm), 5/16" (8mm), 7/16"
(11mm), 9/16" (14mm),
23/32" (18mm), 27/32"
(21mm) & 15/16" (24mm)
A set of 10 Hollow
(6mm), 5/16" (8mm),
3/8" (10mm), 7/16" (11mm),
17/32" (13mm), 9/16"
(14mm), 5/8" (16mm),
3/4" (19mm), 7/8" (22mm)
& 1" (25mm) packed in a
vinyl pouch
section 1
11 Steel stamps <No. 259, No. 261>
esp Juego punzones numeros / letras
fr Jeu de Poincons - numeros / lettres
de Schlagzahlen und Schlag-buchstablen
Number Stamp Set <No. 259>
Letter Stamp Set <No. 261>
The set contains 9 pieces, '0' - '9'. Numbers '6'
& '9' are interchangeable
The set contains 27 pieces, alphabets 'A'
through 'Z' and ampersand '&'
For Hand Held, Hammer struck applications
Cat.Nr.
GROZ, Letter and Number Stamps are
manufactured from selected quality carbon
steel. Punches are through induction hardened,
which gives durability and extended life for
repeated use. The hardness at the stamping end
is maintained at 58-62 HRC, the striking end
is tempered to 38-43 HRC. This prevents the
punch from splintering during use. The striking
end is chamfered to prevent breakage and
accidents due to flying splinters.
Ordering
Nr.
Stamp Size
Cat.Nr.
Inch
mm
Ordering
Nr.
Stamp Size
Inch
mm
NP/1
25900
1/16
1
LP/1
26100
1/16
1
NP/2
25901
3/32
2
LP/2
26101
3/32
2
NP/3
25902
1/8
3
LP/3
26102
1/8
3
NP/4
25903
5/32
4
LP/4
26103
5/32
4
u
NP/5
25904
3/16
5
u
LP/5
26104
3/16
5
u
NP/6
25905
1/4
6
u
LP/6
26105
1/4
6
NP/8
25906
5/16
8
LP/8
26106
5/16
8
NP/10
25907
3/8
10
LP/10
26107
3/8
10
NP/12
25908
1/2
12
LP/12
26108
1/2
12
u
u
u
BESTSELLER
58-62
HRC
UTILITY
automotive
industrial
Indentation
Actual size
E
Inch
1/16
Stamp size
1
(mm)
CB 14
8
E
8
E
8
E
3/32
1/8
5/32
3/16
1/4
5/16
2
3
4
5
6
8
8E
3/8
1/2
10
12
section 1
GROZ CHISELS &
BOLSTERS
Head design
directs striking
force to the tool
centre for greater
resistance to
mushroomingand
chipping
Hardness at
striking end
maintained
under 42 HRC
max
Cold Chisels are primarily used with building
material in masonry applications. Due to the alloy
content in the raw material these can also be used
for cutting, shaping or removing cold metals softer
than the chisel itself. Manufactured from alloy
steel these conform to BS3066.
Bolsters are used for cutting bricks, stone and
paving slabs. The Electrician's Floorboard Bolsters
are used for cutting to tongue in laid tongued
and grooved floorboarding or to remove a part
of a board. Chasing Chisels are used for cutting
channels for cable in cement, plaster, brick etc. All
Bolsters conform to BS 3066 Specification.
SPECIFICATIONS
Cold Chisels are individually forged
from alloy steel. The improved alloy
composition of these chisels allows
them to be used successfully on
building materials and also on metals.
These are accurately hardened and
tempered to applicable DIN, BS,
ANSI & ASTM standards. The cutting
edge is hardened to 52 - 58 HRC
with hardness at the striking end
maintained under 42 HRC max which
ensures that each chisel will provide
optimum cutting efficiency and yet
withstand the shock to which it is
subjected. The shank is powder coated
and the cutting edge accurately
ground.
Premium
Powder
Coated
Finish
Hardness at
cutting edge
52 - 58 HRC
www.groz-tools.com
CB 15
Size marking on
shank allows for easy
identification of the
tool. SAFETY WARNING
is neatly stamped on
the reverse side
Cuttingedgeground
to precise angles for
efficient cutting and
durability
section 1
12 cold chisels Octagonal Cold Chisels
esp Cinceles planas
frCiseaux
deMeißel
Acc BS 3066
Manufactured to the highest safety standards, cold chisels are individually
forged from high quality alloy steel. The alloy content in these makes them
ideal for all types of metalworking and masonry applications and also
increases wear resistance significantly. The precisely ground cutting edge
is induction hardened (52 – 58 HRC) to give improved performance over
longer periods of time. Hardness at the striking end is maintained to under
42 HRC, so that the head will not splinter when subject to hammer blows.
Shank is powder coated and the cutting edge is accurately ground.
They are used for general work on cutting and chipping of metals, and
shaping, facing and cutting of stonework. The extra long chisels are useful
for all cutting and shaping jobs where extra length is required. The larger
size cold chisels are also available with strong impact proof polypropylene
hand guards. These are designed to protect the user’s hands from misplaced
hammer blows.
UTILITY
masonry
industrial
forged
construction
These are available in the following types:
1. Octagonal Cold Chisels
2. Concrete Point Chisels
3. Scutch Holding Chisel
4. Plugging Chisel
W
52-58
HRC
l
CHS/ST/6/ST
A set of 6 Chisels of size 5"x 1/4" (125mm x 6mm),
5" x 5/16"(125 mm x 8mm), 5.5"x 3/8" (140mm
x 10mm, 6" x 1/2"((150 mm x 12mm), 6.5"x 5/8"
(163mm x 16mm), 7" x 3/4" (175mm x 19mm)
CB 16
section 1
Cat.Nr.
Ordering
Nr.
Blade
Width (W)
Inch
mm
Stock
Size
Inch
Overall
Length (L)
mm
Inch
Cat.Nr.
mm
Octagonal Cold Chisels
u
Ordering
Nr.
Blade
Width (W)
Stock
Size
Overall
Length (L)
Inch
mm
Inch
mm
Inch
mm
CHS/ST/8/7-8
32821
7/8
22
3/4
19
8
200
CHS/ST/4/1-4
32827
1/4
6
1/4
6
4
100
CHS/ST/12/7-8
32813
7/8
22
3/4
19
12
300
CHS/ST/5/1-4
32800
1/4
6
1/4
6
5
125
CHS/ST/8/0-1
32807
1
25
7/8
22
8
200
CHS/ST/6/1-4
32828
1/4
6
1/4
6
1/4
150
CHS/ST/9/0-1
32833
1
25
7/8
22
9
225
CHS/ST/5/5-16
32801
5/16
8
1/4
6
5
125
u
CHS/ST/10/0-1
32718
1
25
7/8
22
10
250
CHS/ST/4/3-8
32817
3/8
10
5/16
8
4
100
u
CHS/ST/12/0-1
32814
1
25
7/8
22
12
300
CHS/ST/5/3-8
32829
3/8
10
5/16
8
5
125
CHS/ST/15/0-1
32824
1
25
7/8
22
15
380
CHS/ST/5.5/3-8
32802
3/8
10
5/16
8
5.1/2
140
CHS/ST/18/0-1
32816
1
25
7/8
22
18
450
CHS/ST/6/1-2
32803
1/2
13
7/16
11
6
150
CHS/ST/24/0-1
32834
1
25
7/8
22
24
600
CHS/ST/8/1-2
32818
1/2
13
7/16
11
8
200
Set
CHS/ST/10/1-2
32831
1/2
13
7/16
11
10
250
CHS/ST/6/ST
CHS/ST/12/1-2
32810
1/2
13
7/16
11
12
300
32830
A set of 6 Chisels of size 5"x 1/4" (125mm x 6mm),
5" x 5/16"(125 mm x 8mm), 5.5"x 3/8" (140mm
x 10mm, 6" x 1/2"((150 mm x 13mm), 6.5"x 5/8"
(163mm x 16mm), 7" x 3/4" (175mm x 19mm)
CHS/ST/6.5/5-8
32804
5/8
16
1/2
13
6.1/2
163
CHS/ST/7/5-8
32819
5/8
16
1/2
13
7
175
CHS/ST/12/5-8
32811
5/8
16
1/2
13
12
300
CHS/ST/18/5-8
32820
5/8
16
1/2
13
18
450
u
CHS/ST/10/3-4/GRP/YE
32712
3/4
19
5/8
16
10
250
CHS/ST/7/3-4
32805
3/4
19
5/8
16
7
175
u
32812
3/4
19
5/8
16
12
300
u
CHS/ST/8/3-4
32711
3/4
19
5/8
16
8
200
32815
3/4
19
5/8
16
18
450
u
CHS/ST/10/3-4
32712
3/4
19
5/8
16
10
250
CHS/ST/8/0-1/GRP/YE
32807
1
25
7/8
22
8
200
u
CHS/ST/12/3-4
32812
3/4
19
5/8
16
12
300
u
32718
1
25
7/8
22
10
250
CHS/ST/18/3-4
32815
3/4
19
5/8
16
18
450
u
32814
1
25
7/8
22
12
300
CHS/ST/24/3-4
32832
3/4
19
5/8
16
24
600
32816
1
25
7/8
22
18
450
CHS/ST/7.5/7-8
32806
7/8
22
3/4
19
7.1/2
190
Octagonal Cold Chisels with Grip Guard
u
CB 17
BESTSELLER
section 1
cold chisels (Contd.)
Concrete Point Chisels
Scutch Holding Chisel
These are used for breaking up concrete floors, sidewalks etc. Channels in
concrete floors should be marked out with a flat chisel before using the
Concrete Point Chisel for stock removal.
These are designed for holding detachable stone dressing combs. Due to the
specific nature of application these are not hardened
Cat.Nr.
Cat.Nr.
CRP/150-13
Ordering
Nr.
32650
Point Size (P)
Stock Size
Overall Length (L)
Ordering
Nr.
Scutch Width
Stock Size
Overall Length
Inch
mm
Inch
mm
Inch
mm
Inch
mm
Inch
mm
Inch
mm
CHS/SCH/01
32656
1
25
5/8
16
8
200
5/32
4
1/2
13
6
150
CHS/SCH/1-1-2
32657
1.1/2
38
5/8
16
8
200
CRP/200-13
32651
5/32
4
1/2
13
8
200
CRP/250-16
32652
7/32
5
5/8
16
10
250
u
CRP/250-19
32653
1/4
6
3/4
19
10
250
u
CRP/300-19
32654
1/4
6
3/4
19
12
300
u
BESTSELLER
Plugging Chisel
These are designed to remove the mortar or cement between bricks or for
the complete removal of bricks. The cutting edge is wider than the blade to
give maximum clearance and the flute allows faster clearance of debris.
UTILITY
Cat.Nr.
forged
construction
masonry
CHS/PLG/01
Ordering
Nr.
32655
Blade Width
Stock Size
Overall Length
Inch
mm
Inch
mm
Inch
mm
1/4
6
5/8
16
10
250
P
52-58
HRC
l
< Plugging Chisel
<ConcretePointChisels
CB 18
ScutchHoldingChisel>
section 1
13 Wrecking Bars <No. 331W>
14 BRICKLAYER'S LINE PINS
esp Barras de descencofrar
fr Pince a decoffrer
deNageleisen
esp Línea Perno Del Albañil
fr Ligne Epingle de Maçon
de Maurer-Linie Stift
Manufactured from octagonal section steel, Wrecking Bars have a forged
construction. These are useful for leveraging timber and for pulling out
nails from timber, dismantling wooden crates etc. All Wrecking Bars come in
attractive powder coated finish
Used in conjunction with builder's lines for marking out positions or aligning
brickwork etc. Line Pins are individually forged.
Cat.No.
u
u
Ordering
Nr.
Length
Accurately hardened these are suitable for use with hardened mortar as
well. Line Pins have a rust inhibiting plated finish and are sold as a set of
two
Section
Inch
mm
Inch
mm
WB/000
33100
12
300
5/8
16
WB/00
33101
16
400
5/8
16
WB/01
33102
18
450
5/8
16
WB/02
33103
20
500
5/8
16
WB/03
33104
24
600
3/4
19
WB/04
33105
28
700
3/4
19
WB/05
33106
30
750
3/4
19
WB/07
32818
36
900
3/4
19
WB/06
33107
40
1000
3/4
19
Cat.No.
LPN/01/ST
32659
Overall Length
Inch
mm
6
150
UTILITY
masonry
u
Ordering
Nr.
forged
construction
BESTSELLER
Line Pin being
used for aligning
wall with corner
CB 19
section 1
15 Bolsters <BRC-75, BRC-100; FLR-63, FLR-75>
esp Cinceles-ladrillo & suelo
fr Ciseau a brique & Ciseau pour electricien
de Schlitzmeißel fur Steinbearbeitung und Elektrikermeißel
Brick Bolster <BCR-75, BCR-100>
Brick Bolsters are used for cutting brick, stone & paving slabs. These should
not be used on concrete containing reinforcing bars
Acc BS 3066
Bolsters are manufactured as a single piece forging from high quality carbon
steel, accurately hardened to BS 3066 specification.
Brick Bolsters
Cat.No.
The cutting edge is hardened 52 - 58 HRC with the striking end maintained
under 42 HRC
The complete Bolster is powder coated and the cutting edge is accurately
ground. Each Bolster is permanently marked with safety warning message.
Ordering
Nr.
Blade
Width (W)
Stock
Size
Overall
Length (L)
Inch
mm
Inch
mm
Inch
mm
u
BRC/75
32601
3
75
7/8
22
9
230
u
BRC/100
32602
4
100
7/8
22
9
230
l
BRC/115
32603
4.1/2
115
1
25
9
230
Brick Bolsters with Guard
Brick Bolsters are also available with polypropylene hand guards. These
hand guards are designed to protect the user's hands from misplaced
hammer blows.
u
BRC/75/GRP/YE
32621
3
75
7/8
22
9
230
u
BRC/100/GRP/YE
32622
4
100
7/8
22
9
230
l
BRC/115/GRP/YE
32628
4.1/2
115
1
25
9
230
u
BESTSELLER l NEW
forged
construction
W
UTILITY
52-58
HRC
l
masonry
< Brick Bolster
CB 20
< Brick Bolster
with grip guard
section 1
Electrician's Bolster <FLR-63, FLR-75>
Chasing Chisel
With a much thinner blade construction than a Brick Bolster, Electricians
Floorboard Bolsters are used for cutting tongued joints & lifting floorboards.
Chasing Chisels are used for cutting channels for cables in cement plaster,
brick etc. These should not be used for prising up floorboards.
Floor Chisels / Electrician Bolster
Cat.No.
u
Ordering
Nr.
Blade
Width (W)
Stock
Size
Overall
Length (L)
Inch
mm
Inch
mm
Inch
mm
FLR/CHS/9/2-1-2
32642
2.1/2
63
5/8
16
9
230
FLR/CHS/12/0-3
32641
3
75
3/4
19
12
300
Cat.No.
CHS/CC/50
Ordering
Nr.
Blade
Width (W)
Stock
Size
Overall
Length (L)
Inch
mm
Inch
mm
Inch
mm
2
50
3/4
19
9
225
32658
Floor Chisels / Electrician Bolsters with Guard
u
u
FLR/CHS/9/2-1-2/GRP/YE
32643
2.1/2
63
5/8
16
9
230
FLR/CHS/12/0-3/GRP/YE
32645
3
75
3/4
19
12
300
W
BESTSELLER
52-58
HRC
l
W
52-58
HRC
l
< Electrician's Bolster
CB 21
< Electrician's Bolster
with grip guard
< Chasing Chisel
section 1
16 punch and chisel kits
esp Juego punzones & cinceles
fr Jeu de Poincons et ciseaux
de Meißel-und Durchschläger - Sätze
CAT.Nr.: KIT/24/ST Ordering Nr.: 33003 / 24 PC punch and chisel kit
Constituents
Blade Width
Inch
mm
Stock Size
Inch
mm
Overall Length
Inch
mm
A range of kits carefully thought about, keeping in mind the needs of the
journeyman… the farmer or rancher…. the mechanic ….the carpenter. This
is an excellent way to keep your tools organized. These kits are packed in
heavy-duty vinyl rolls for easy access, organization and storage
UTILITY
CHS/ST/5/1-4
1 /4
6
1 /4
6
5
125
CHS/ST/5/5-16
5/16
8
1 /4
6
5
125
CHS/T/5.5/3-8
3/8
10
5/16
8
5.1/2
140
CHS/ST/6/1-2
1 /2
13
7/16
11
6
150
CHS/ST/6.5/5-8
5 /8
16
1 /2
13
6.1/2
163
CHS/ST/7/3-4
3 /4
19
5 /8
16
7
175
CHS/ST/7.5/7-8
7/8
22
3 /4
19
7.1/2
190
Centre Punches – Heavy Duty
industrial
CP/HD/1-4
1/ 4
6
1 /2
12
6
150
CP/HD/5-32
5/32
4
3/8
10
5
125
CP/HD/5-64
5/64
2
1 /4
6
3.1/2
90
100
Pin Punches – Heavy Duty
PP/HD/1-16
1/16
1.5
1 /4
6
4
PP/HD/3-32
3/32
2.5
5/16
8
4.1/2
112
PP/HD/1-8
1/8
3
5/16
8
4.3/4
119
PP/HD/5-32
5/32
4
5/16
8
5
125
PP/HD/3-16
3/16
5
3/8
10
5.1/4
132
PP/HD/1-4
1 /4
6
3/8
10
5.3/4
145
PP/HD/5-16
5/16
8
7/16
11
6
150
125
Starting Punches – Heavy Duty
SGP/HD/1-16
1/16
1.5
3/8
10
5
SGP/HD/1-8
1/8
3
3/8
10
5
125
SGP/HD/5-32
5/32
4
3/8
10
5
125
125
SGP/HD/3-16
3/16
5
3/8
10
5
SGP/HD/1-4
1/4
6
3/8
10
5
125
SGP/HD/5-16
5/16
8
1/ 2
12
6
150
ACP/1B
Automatic Center Punch, Black Powder Coated – Length
4.3/4" (120 mm), Body Diameter 33/64" (13 mm)
KIT/24/ST
CB 22
section 1
CAt.Nr.: KIT/26/ST Ordering Nr.: 33004 / 26 PC punch and chisel kit
Constituents
Blade Width
Inch
mm
Stock Size
Inch
mm
Overall Length
Inch
CAT. Nr.: KIT/14/ST Ordering Nr.: 33001 / 14 PC punch and chisel kit
Constituents
mm
Blade Width
Stock Size
Inch
mm
Inch
Overall Length
mm
Inch
mm
CHS/ST/5/1-4
1 /4
6
1 /4
6
5
125
CHS/T/5.5/3-8
3/8
10
5/16
8
5.1/2
140
CHS/ST/5/5-16
5/16
8
1 /4
6
5
125
CHS/ST/6/1-2
1/2
13
7/16
11
6
150
CHS/T/5.5/3-8
3/8
10
5/16
8
5.1/2
140
CHS/ST/6.5/5-8
5 /8
16
1/2
13
6.1/2
163
CHS/ST/6/1-2
1 /2
13
7/16
11
6
150
CHS/ST/7/3-4
3 /4
19
5/8
16
7
175
CHS/ST/6.5/5-8
5 /8
16
1 /2
13
6.1/2
163
CHS/ST/7.5/7-8
7/8
22
3 /4
19
7.1/2
190
CHS/ST/7/3-4
3 /4
19
5 /8
16
7
175
CHS/ST/7.5/7-8
7/8
22
3 /4
19
7.1/2
190
CP/HD/5-32
5/32
4
3/8
10
5
125
CHS/ST/8/0-1
1
25
1 /2
13
8
200
CP/HD/1-4
1/4
6
1/2
12
6
150
CHS/ST/12/1-2
1 /2
13
7/16
11
12
300
PP/HD/1-16
1/16
1.5
1 /4
6
4
CP/HD/1-4
1/ 4
6
1 /2
12
6
150
PP/HD/1-8
1/8
3
5/16
8
4.3/4
119
CP/HD/3-8
3/8
10
5/8
16
6.1/4
160
PP/HD/3-16
3/16
5
3/8
10
5.1/4
132
CP/HD/5-32
5/32
4
3/8
10
5
125
Drift Punches – Heavy Duty
DFP/HD/1-8
1/8
3
5/16
8
8
200
2.5
5/16
8
4.1/2
112
DFP/HD/5-32
5/32
4
3/8
10
9
225
PP/HD/3-32
3/32
100
PP/HD/1-8
1/8
3
5/16
8
4.3/4
119
PP/HD/5-32
5/32
4
5/16
8
5
125
SGP/HD/5-16
5/16
8
1/2
12
6
150
PP/HD/3-16
3/16
5
3/8
10
5.1/4
132
SGP/HD/1-8
1/8
3
3/8
10
5
125
PP/HD/1-4
1 /4
6
3/8
10
5.3/4
145
PP/HD/3-8
3/8
10
1 /2
12
6.1/2
163
125
SGP/HD/1-16
1/16
1.5
3/8
10
5
SGP/HD/1-8
1/8
3
3/8
10
5
125
SGP/HD/3-16
3/16
5
3/8
10
5
125
SGP/HD/1-4
1/4
6
3/8
10
5
125
DFP/HD/1-8
1/8
3
5/16
8
8
200
DFP/HD/3-16
3/16
5
1/ 2
12
10
250
DFP/HD/1-4
1/4
6
5/8
16
12
300
4
3/8
10
5
125
PKP/HD/3-8
5/32
UTILITY
industrial
KIT/26 >
< KIT/14
CB 23
section 1
punchandchiselkits(Contd.)
Cat.Nr.: KIT/16/ST Ordering Nr.: 33002 / 16 PC punch and chisel kit
CAT.Nr.: KIT/8/ST Ordering Nr: 33000 / 8 PC punch and chisel kit
Constituents
Blade Width
Inch
mm
Stock Size
Inch
mm
Overall Length
Inch
Constituents
Blade Width
Inch
mm
mm
Stock Size
Inch
Overall Length
mm
Inch
mm
CHS/ST/6/1-2
1 /2
13
7/16
11
6
150
CHS/ST/5/5-16
5/16
8
1 /4
6
5
125
CHS/ST/6-5/5-8
5 /8
16
1 /2
13
6.1/2
163
CHS/ST/6/1-2
1 /2
13
7/16
11
6
150
CHS/ST/7/3-4
3 /4
19
5 /8
16
7
175
CHS/ST/6-5/5-8
5 /8
16
1 /2
13
6.1/2
163
CHS/ST/7/3-4
3 /4
19
5 /8
16
7
175
CHS/ST/8/7-8/SPL
7/8
22
5/8
16
8
200
CP/HD/5-32/SPL
5/32
4
5/16
10
5.1/2
125
PP/HD/1-8
1/8
3
5/16
8
4.3/4
119
CP/HD/1-8
1/8
3
5/16
8
4.1/4
108
PP/HD/3-16/SPL
3/16
5
5/16
8
5.1/4
132
CP/HD/5-32/SPL
5/32
4
5/16
8
5.1/2
138
PP/HD/1-4
1 /4
6
3/8
10
5.3/4
145
CP/HD/1-4/SPL
1 /4
6
3/8
10
6
150
SGP/HD/3-16
3/16
5
3/8
10
5
125
UTILITY
automotive
PP/HD/1-8
1/8
3
5/16
8
4.3/4
119
PP/HD/3-16/SPL
3/16
5
5/16
8
5.1/4
132
PP/HD/1-4
1 /4
6
3/8
10
5.3/4
145
DFP/HD/3-16/SPL
3/16
5
5/16
8
10
250
DFP/HD/1-4/SPL
1 /4
6
3/8
9.5
10
250
industrial
SGP/HD/1-8/SPL
1/8
3
5/16
8
5
125
SGP/HD/3-16
3/16
5
3/8
10
5
125
UTILITY
< KIT/8/ST
automotive
industrial
KIT/16/ST>
CB 24
section 1
Constituents
Blade Width
Inch
mm
Stock Size
Inch
mm
Overall Length
Inch
Constituents
mm
Blade Width
Stock Size
Inch
mm
Inch
mm
Overall Length
Inch
mm
CHS/ST/6/1-2
1 /2
13
7/16
11
6
150
CHS/ST/6/1-2
1 /2
13
7/16
11
6
150
CHS/ST/6-5/5-8
5 /8
16
1 /2
13
6.1/2
163
CHS/ST/6-5/5-8
5 /8
16
1 /2
13
6.1/2
163
CHS/ST/7/3-4
3 /4
19
5 /8
16
7
175
CHS/ST/7/3-4
3 /4
19
5 /8
16
7
175
CP/HD/5-32
5/32
4
5/16
8
5.1/2
138
CP/HD/1-4
1 /4
6
PP/HD/1-8
1/8
3
5/16
8
4.3/4
119
PP/HD/1-8
1/8
3
5/16
8
4.3/4
119
PP/HD/3-16/SPL
3/16
5
5/16
8
5.1/4
132
PP/HD/3-16/SPL
3/16
5
5/16
8
5.1/4
132
PP/HD/1-4
1 /4
6
3/8
10
5.3/4
145
PP/HD/5-16
5/16
8
7/16
11
6
150
PP/HD/3-32/SPL
3/32
2.5
1/4
6
4.1/4
108
DFP/HD/5-32
5/32
4
3/8
10
9
230
UTILITY
DFP/HD/3-16
3/16
5
1/2
13
10
250
DFP/HD/5-32/SPL
5/32
4
1/2
13
10
250
DFP/HD/3-8/SPL
3/8
10
5/8
16
10
250
10
3/8
10
5
125
Prick Punches – Heavy Duty
automotive
PKP/HD/3-8
3/8
UTILITY
< KIT/7/ST
automotive
kit/13/st>
CB 25
section 1
17 Chisel&Bolster-Merchandiserpacks
esp Botadores y Cinselesseporte
fr Poincons et Ciseaux support
de Durchschläge und Meibel Standplatz
Well designed and constructed merchandisers for
convenient and safe display of bolsters and chisels.
Clean cut slots, with the cutting edge facing
downwards help in safe storage.
Come complete with constituents for ready display
on the shelf
UTILITY
masonry
Cat Nr. DST/01/ST
Ordering Nr. : 33050
Merchandiser with 64 slots for holding 8 each of:
Plugging Chisels
Cold Chisels 8" x 1/2"
(Groz Ref: CHS/PLG/01)
(Groz Ref CHS/ST/8/1-2)
1" Scutch Holding Chisels
(Groz Ref CHS/SCH/01)
Cold Chisels 10" x 1"
(Groz Ref CHS/ST/10/0-1
Cold Chisels 8" x 3/4"
(Groz Ref CHS/ST/8/3-4)
Floor Chisel 2.1/2"
(Groz Ref FLR/CHS/9/2-1-2)
Brick Bolster 4"
(Groz Ref BRC/100)
Brick Bolster 3"
(Groz Ref BRC/75)
Cat. Nr. DST/02/ST
Ordering Nr. : 33051
Merchandiser with 18 slots
for holding
4 each of:
Floor Chisel 2.1/2"
(Groz Ref FLR/CHS/9/2-1-2)
Brick Bolster 4"
(Groz Ref BRC/100)
Brick Bolster 3"
(Groz Ref BRC/75)
& 2 each of:
Floor Chisel 2.1/2" with grip
(Groz Ref FLR/CHS/9/2-1-2/GRP/
YE)
Brick Bolster 4" with grip
(Groz Ref BRC/100/GRP/YE)
Brick Bolster 3" with grip
(Groz Ref BRC/75/GRP/YE)
CB 26
section 1
www.groz-tools.com
2
Center Punches 8 Pin Punches 10 Starting Punches 14 Drift Punches 14 Roll Pin Punches 15
Hinge Centering Punch 15 Prick Punches 16 Nail Punches 16 Automatic Centre Punches 17
Hollow & Arch Punches 18 Steel Stamps 20 Cold Chisels 22 Wrecking Bar 25
Bricklayer's Line Pins 25 Bolsters 26 Punch & Chisel Kits 28 Chisel & Bolsters CB 33
section 2
18 Professional Mechanic’s Vices - Bench Vices <Series BV>
esp Tornillos de banco
frEtaux de mecanicien
deParallel - Schraubstöcke
Cat. Nr.
Ordering
Nr.
Jaw
Width
Inch
Jaw
Opening
mm
Inch
mm
Throat
Depth
Net Wt.
Each
Inch
mm
Kg.
5.500
Fixed Base Vices
Groz manufactures a comprehensive range of mechanic’s vices useful for
all medium to heavy duty applications. Manufactured from high quality
grey iron castings - a very strong material with excellent shock absorbing
capacity and immense strength under compression, these rigid & robust
vices machined to close tolerances, are designed for smooth operation and
reliability.
The front jaw beam with machined construction fully encloses the vice
spindle protecting the threads from contaminants and damage. The
long unbreakable malleable iron nut securely locked in the body ensures
maximum thread surface contact and constant alignment between body and
the sliding jaw. Jaws are hardened 45 + 5 HRC. Perfect alignment of main
screw and nut reduces wear and gives long trouble free service. Vices have
an attractive blue finish with main screw and handle plated. The anvil has a
ground finish.
A common sight in almost all workshops and garages, these are available
with a fixed base for regular usage or a swivel base that allows rotation
through 360º with firm locking at any position. The swivel base allows the
vice to be used in confined spaces or where the angle of the vice has to be
adjusted to accept work of varying lengths. The swivel base can be easily
removed and the vice converted back to a regular fixed base vice.
u
u
BV/F/75
35400
3
75
4
100
2
50
BV/F/100
35401
4
100
5
125
2.5/32
55
9.200
BV/F/125
35402
5
125
6
150
2.3/4
70
15.700
BV/F/150
35403
6
150
7
175
3.5/32
80
21.400
BV/F/200
35404
8
200
8
200
4
100
32.000
Swivel Base Vices
BV/S/75
35405
3
75
4
100
2
50
7.500
BV/S/100
35406
4
100
5
125
2.5/32
55
12.000
u
BV/S/125
35407
5
125
6
150
2.3/4
70
20.600
u
BV/S/150
35408
6
150
7
175
3.5/32
80
26.400
BV/S/200
35409
8
200
8
200
4
100
44.000
Swivel Bases
Cat. Nr.
Ordering
Nr.
Suitable for Vice
With Jaw Width
SWB/75
35420
3"
75 mm
SWB/100
35421
4"
100 mm
SWB/125
35422
5"
125 mm
SWB/150
35423
6"
150 mm
SWB/200
35424
8"
200 mm
u
BESTSELLER
20000 PSI
< Fixed BaseVice
1400 Kgf/cm2
Cast
tensile
strength
UTILITY
automotive
industrial
WARNING
< Swivel Base Vice
CB 34
no
hammering
section 2
19 Engineer’s Steel Bench Vices <Series EBV & Series OBV>
esp Tornillos de acero para ingenieros
frEtaux d' acier de Ingénieur
deParallel - Schraubstöcke
Cat.Nr.
Ordering
Nr.
Jaw
Width (W)
Inch
Jaw
Opening
mm
Inch
Throat
Depth (D)
mm
Inch
Net Wt
mm
kgs
Regular Jaw Vices
With an all steel construction, these fixed base vices are built to withstand
the shocks of hammering, chipping and other tough applications.
Each vice has an integrated anvil for shaping and beating, together with an
extra heavy-duty sliding jaw and large diameter screw. Forged tommy bar
along with the steel main screw helps in effective transmission of pressure
on the work piece.
Carbon Steel jaws are hardened 50 + 5 HRC to withstand tough use and
are serrated for non-slip grip. Safety stopper provided at the end of slide
prevents slide from fall during usage.
Also available is the Offset Jaw Vice: Offset jaw design allows for unlimited
vertical depth for holding long jobs without any obstruction from the vice
slide
EBV/F/100
35450
4
100
4.3/4
120
3.5/32
80
4.5
u
EBV/F/150
35451
6
150
6
150
3.5/8
90
14
u
EBV/F/200
35452
8
200
8
200
4.3/8
110
31
Offset Jaw Vices
u
u
OBV/F/100
35460
4
100
4.3/4
120
—
—
7
OBV/F/150
35461
6
150
7
175
—
—
20
OBV/F/200
35462
8
200
8
200
—
—
34
BESTSELLER
<RegularJawVice
UTILITY
automotive
industrial
Offset JawVice >
Offsetjawsholdlong
& bulky jobs without
obstructionfromthe
vice slide
CB 35
section 2
20 Drill Press Vices — Unigrip <Series UG>
esp Mordazas para Taladro
frEtaux de perceuse
deBohrmaschinenschraubstocke
Fully ground side face allows for right
angle machining with the same jaw
setting.Thejawwidthactsasjawheight
facilitatinglongerworkpiecestobeheld
Sturdy craftsman design for drill stands, bench drills and drill presses, these
compact vices have a low profile format making them suitable for multitude
of metal working and woodworking applications.
Manufactured from graded cast iron, vices have a precision ground base and
vice bed for smooth lateral movement of the movable jaw. Fixed jaw with
3 longitudinal and 1 transversal prisms allows firm gripping of round stock
both horizontally and vertically. Special seat in jaws facilitates clamping of
low height work pieces. Spindle moves inside the hollow hand grip allowing
the vice to be tightened at any position on the table thus increasing
the scope of application of the vice. Elongated clamping slots for rapid
adjustment of the vice on the work table help save time.
This vice is also available with 3 mounting options via 2 additional precisely
ground surfaces: end face and side face. This allows for drilling along all
axes with a single setting of the job and holding of long workpieces which
are cumbersome and difficult to manage in regular vices.
Drill Press Vices - Unigrip
Cat. Nr.
Ordering
Nr.
Jaw Width
Jaw Opening
Fully ground
end face allows
for right angle
machining
with the same
machinesetting
Jaw Depth
Inch
mm
Inch
mm
Inch
mm
DPV/UG/75
35120
3.3/16
80
2.3/4
70
1.3/16
30
u
DPV/UG/100
35121
4
100
3.5/8
92
1.3/16
30
u
DPV/UG/125
35122
5
120
4.3/8
110
1.3/8
35
100
3.1/2
88
1.3/16
30
3 Way Drill Press Vice – Unigrip
DPV/UG/3/100
35125
4
Cast
UTILITY
industrial
<3WayDrillPressVice-Unigrip
< Drill Press Vice - Unigrip
CB 36
section 2
21 DIY Drill Press Vices <Series CI>
esp Mordazas para Taladro - DIY
frEtaux de perceuse - DIY
deBohrmaschinenschraubstocke-DIY
Useful for light drilling operations, these vices are manufactured from
graded cast iron and have a ground base for smooth movement. Fixed
jaw with 3 longitudinal and 1 transversal prisms allows firm gripping of
round stock both horizontally and vertically. Special seat in jaws facilitates
clamping of low height work pieces
Cat.Nr.
Ordering
Nr.
Jaw Width
Jaw Opening
Jaw Depth
Inch
mm
Inch
mm
Inch
mm
DPV/CI/63
35194
2.1/2
63
2.3/8
61
1
25
DPV/CI/80
35195
3.3/16
80
3.9/32
84
1
25
DPV/CI/100
35196
4
100
3.3/8
86
1
25
Cast
UTILITY
industrial
www.groz-tools.com
No matter what the job at hand
may be, Groz vices are always
ready to face the challenge head
on. It's not surprising that most
people put their money on Groz
when it comes to the crunch.
Built Tough. Tough to Beat
CB 37
section 2
22 reversible vice <RV 37>
esp Tornillos de Banco - Reversible
frEtaux - Réversible
deSchraubstöcke - Umschaltbar
Cat.Nr.
Ordering
Nr.
RV/75-175
35530
Jaw
Width
Jaw
Opening
Throat
Depth
Pipe Jaw
Capacity
Inch
mm
Inch
mm
Inch
mm
Inch
mm
3.1/2
90
3.1/2
90
1.1/2
40
7/8
22
Reversed
A compact and convenient vice suitable for a variety of DIY applications.
Unique design additionally allows it to be used as a Pen Press.
7
175
Made from cast iron, the body and sliding jaw are aligned with two steel
guide rods and the main screw for smooth action. Polypropylene jaws
impart a soft yet firm grip. Under pressure these jaws deform around the
work piece and return to their original shape when the work is removed.
Jaw capacity can be doubled from 3.1/2" (90mm) to 7" (175mm) by
removing the sliding jaw and placing it at the back of the body-making the
vice reversible.
V Grooved
polypropylene
jaws help
in holding
round and
thin materials
gently but
firmly
With a 360° swivel base this is amongst the most versatile and convenient
work holding tools
Cast
UTILITY
woodworking
Pipe jaws for
holding pipes
upto 7/8"
(22 mm)
REVERSIBLE - Jaw capacity can be doubled from
3.1/2"(90mm)to7"(175mm)byremovingthemain
screw,guide,rods,slidingjawsectionandplacingit
in the back of the body
CB 38
section 2
23 Hobbyist Vices <No. 355>
esp Tornillos de banco bricolage
frEtau a agrafe amateur
deMini-Schraubstöck
Groz manufactures a complete range of compact vices for a wide variety of
metal and woodworking applications. While ideal for use by model makers
and DIY enthusiasts, these can also be used by the serious craftsman for
light duty jobs. Manufactured from high quality grey iron castings, these are
machined to close tolerances resulting in smooth operation and reliability.
Vices have an attractive enamelled finish with main screw and handle in
chrome plated finish. These are available in 3 types:
Hobbyist Vices with fixed and swivel bases
For applications that involve working in confined spaces, the swivel base
vice is the ideal answer.
Hobbyist Vices with an integrated clamp
The integrated clamp renders portability to the vice allowing it to be
clamped conveniently onto any working surface.
Hobbyist Vice with
swivel base and
integrated clamp
Hobbyist Vice with swivel base and integrated clamp
Portable and compact, the built in clamp allows the vice to be clamped onto
any surface 1.1/2" (38 mm) deep easily. The swiveling base further enhances
the versatility of the vice.
Cat. Nr.
Ordering
Nr.
Jaw Width
Integrated Clamp Capacity
Inch
mm
Inch
mm
Fixed Base
TBV/FB/32
35510
1.1/4
32
--
--
TBV/FB/40
35511
1.5/8
40
--
--
TBV/FB/50
35512
2
50
--
--
TBV/FB/60
35513
2.3/8
60
--
--
TBV/FB/75
35514
3
75
--
--
TBV/SB/32
35515
1.1/4
32
--
--
TBV/SB/40
35516
1.5/8
40
--
--
TBV/SB/50
35517
2
50
--
--
u
TBV/SB/60
35518
2.3/8
60
--
--
u
TBV/SB/70
35519
3
75
--
--
u
Swivel Base
Hobbyist Vices with an
integrated clamp
With Integrated Clamp
u
TBV/C/32
35521
1.1/4
32
1.1/8
29
TBV/C/40
35522
1.5/8
40
1.3/8
35
TBV/C/50
35523
2
50
1.3/8
35
TBV/C/60
35524
2.3/8
60
1.11/16
43
TBV/C/75
35525
3
75
1.3/4
45
TBV/C/100
35526
4
100
1.3/4
45
1.1/2
38
With Swivel Base and Integrated Clamp
u
TBV/RC/50
u
BESTSELLER
35520
2
50
Fixed Base Vice
Cast
UTILITY
Swivel Base Vice
CB 39
section 2
24 HAND VICES
25 Anvils — Cast Steel
esp Tornillos manuales
frEtaux manuels
deHandfeilkloben
espYunques
frEnclumes
deAmbosse
Manufactured from high grade cast iron, these vices are best suited for
working on small jobs. The vice can either be gripped in one hand or held
between the jaws of a larger vice thus allowing better access to the work
piece. The jaws are tightened by means of a large wing nut. Vice body has
an attractive enamelled finish, the main screw is plated which prevents
corrosion
Professional quality anvils, these are manufactured from cast steel
that allows these to be used for far more rigorous applications than a
conventional cast iron anvil. The anvil face is precision ground and provided
with Pritchel & Hardy holes .The beak is strong and can be used for bending
applications. Anvil body has an attractive oven baked finish. An unbreakable,
indispensable tool for any workshop
Cat. Nr.
u
Ordering
Nr.
Overall Length
Jaw Width
Inch
mm
Inch
mm
Cat. Nr.
Ordering
Nr.
Size
Kg
lbs
11
HV/75
35500
3
75
1.3/8
35
AVL/CS/5
14210
5
HV/100
35501
4
100
1.9/16
40
AVL/CS/10
14211
10
22
HV/125
35502
5
125
2
50
AVL/CS/15
14212
15
33
u
Cast
UTILITY
u
AVL/CS/20
14213
20
44
AVL/CS/30
14214
30
66
AVL/CS/40
14215
40
88
AVL/CS/50
14216
50
110
AVL/CS/60
14217
60
132
AVL/CS/75
14219
75
165
AVL/CS/80
14220
80
176
BESTSELLER
Cast
CB 40
section 2
26 GClamps-GeneralPurpose <Series13D,SeriesOH>
esp Tornillo para Ebanisteria
frSerre-joints type G
deG-Schraubzwingen
Cat. Nr.
The Groz 13D Series G clamps are by far the most superior and popular
amongst various G clamps of this category. Manufactured from SG iron with
a tensile strength of over 60,000 PSI these are guaranteed unbreakable
under normal usage. Further, the handle is so designed that it will bend
before the frame can be overstressed. Steel main screw has ACME threads
for smooth operation. The swiveling pad adopts the correct angle and
applies even pressure on the work piece.
Frames have attractive textured powder coated finish with spindle in black
oxide finish for increased resistance to corrosion.
Ordering
Nr.
Capacity (C)
Throat Depth (D)
Frame Proof Load
Inch
mm
Inch
mm
Kgs
lbs
50
1.5/8
42
363
800
GCL/13D/50
35807
2
GCL/13D/75
35800
3
75
1.11/16
44
455
1000
u
GCL/13D/100
35801
4
100
2.11/32
59
545
1200
u
GCL/13D/150
35802
6
150
3
75
635
1400
GCL/13D/200
35803
8
200
3.1/8
80
775
1700
GCL/13D/250
35804
10
250
3.1/2
90
1000
2200
GCL/13D/300
35805
12
300
4
100
1135
2500
One Hand G Clamp
u
u
GCL/OH/4
35850
4
100
2.3/8
61
545
1200
GCL/OH/6
35851
6
150
3.3/32
79
635
1400
BESTSELLER
C
Also available
One Hand Operated G Clamp: A unique design that is operated using just
one hand leaving the other free for holding workpiece
D
These are useful for a variety of metal and woodworking applications
Cast
<SeriesOH
UTILITY
woodworking
industrial
CB 41
One Hand G
Clamps can be
operatedbyone
hand using the
special knurled
nut, leaving the
other hand free
to hold the item
being clamped
<Series13D
section 2
27 G Clamps — Drop Forged <Series F>
esp Tornillo para hierro forjado - trabajos pesados
frSerre-joints type G - Estampe
deG-Schraubzwingen
Drop forged steel body with ribs for added strength and rigidity. The steel
mainscrew has precisely cut threads for added strength with broad steel
swivel pad which adopts the correct angle and applies pressure evenly.
Clamp design ensures that the handles will bend before the frame can
be overstressed. These are suitable for all industrial applications and
construction jobs demanding extra strength. The clamps have a rust
resistant grey enamelled finish.
These are available with :
Cat. Nr.
Ordering
Nr.
Grey Frame with
Black spindle
u
u
u
Cat. Nr.
Ordering Capacity
Nr.
(C)
Grey frame with
Copper spindle
Throat
Frame
Depth (D) Proof Load
Inch
mm
Inch
mm
Kgs
lbs
2700
GCL/F-50/BL
35700
GCL/F-50
35740
2
50
1.1/2
38
1225
GCL/F-75/BL
35701
GCL/F-75
35741
3
75
2
50
1450
3200
GCL/F-100/BL
35702
GCL/F-100
35742
4
100
2.3/8
60
1675
3700
GCL/F-150/BL
35703
GCL/F-150
35743
6
150
3
75
2125
4700
GCL/F-200/BL
35704
GCL/F-200
35744
8
200
3.3/8
85
2350
5200
BESTSELLER
C
D
Black Oxide Spindle
Black oxidation as against zinc plating provides for smoother operation and
retards corrosion
Copper Plated Spindle
Useful in welding application as copper plating is resistant to welding spatter
and also inhibits corrosion
UTILITY
industrial
forged
construction
With Copper Plated Spindle
With Black Oxide Spindle
The serrated swivel pad
alongwith vee grooved
anvil helps in securely
holdingroundandirregular
shape jobs
CB 42
section 2
28 GClamps—DropForged—HeavyDuty <SeriesFH>
esp Tornillo para hierro forjado - trabajos pesados
frSerre-joints ultrarobustes type G - Estampe
deG-Schraubzwingen
Particularly suitable for metalworking and fabrication work, these G clamps
are drop forged from high grade steel. The frames are ribbed, stressed and
shaped to absorb tensions and compressions well within the limits of the
material from which they are made. The steel mainscrew has precisely cut
Acme threads for smooth operation, fast action and maximum clamping
pressure. The serrated swivel pad alongwith vee grooved anvil helps in
securely holding round and irregular shape jobs. The deep throat design
helps clamping well in from the edge of the work.
These are available with:
Black Oxide Spindle
Black oxidation as against zinc plating provides for smoother operation and
retards corrosion
Useful in welding application as copper plating is resistant to welding spatter
and also inhibits corrosion
Cat. Nr.
Ordering
Nr.
Capacity
(C)
Throat
Depth (D)
Inch
mm
Inch
Frame Proof
Load
mm
Kg
lbs
Black Oxide Spindle
u
GCL/F/H-100/BL
35713
4
100
3.1/4
82
2820
6200
u
GCL/F/H-150/BL
35714
6
150
4
100
3000
6600
GCL/F/H-200/BL
35715
8
200
5
125
3135
6900
u
GCL/F/H-100
35710
4
100
3.1/4
82
2820
6200
u
GCL/F/H-150
35711
6
150
4
100
3000
6600
GCL/F/H-200
35712
8
200
5
125
3135
6900
u
With Copper
Plated Spindle
BESTSELLER
D
C
forged
construction
UTILITY
industrial
With Black
Oxide Spindle
CB 43
section 2
29 G Clamps — Junior <Series FSJ>
30 GClamps—Hobbyist’s <SeriesSM>
esp Tornillo junior
frPresses en C "Junior"
de Junior G-Schraubzwingen
esp Torniquete tipo "G"
frPresse en G
de G-Schraubzwingen Stanzbelch
Clamps are individually forged making them amongst the strongest junior
G Clamps. Frames are powder coated and Steel Screws are Zinc Plated for
increased resistance to corrosion
General purpose light duty clamps manufactured from high quality welded
steel plates with plated screw, handle and swivel pad. Strong, yet relatively
light in weight, these have the added advantage of a slim section. Slim
section allows for more clamps to be used in a given space. These clamps
are particularly useful for the craftsmen with smaller work, and the DIY
enthusiasts
Cat. Nr.
Ordering
Nr.
Capacity
(C)
Throat Depth
(D)
Frame
Proof Load
Inch
mm
Inch
mm
Kgs
lbs
GCL/FSJ/1
35730
1
25
1
25
225
500
GCL/FSJ/1-1-4
35731
1.1/4
31
1.1/4
31
365
800
u
GCL/FSJ/1-1-2
35732
1.1/2
38
1.1/2
38
385
850
GCL/SM/1
u
GCL/FSJ/0-2
35733
2
50
1.1/4
31
400
875
u
GCL/FSJ/0-3
35735
3
75
1.3/8
35
500
1100
GCL/FSJ/2-1-2
35734
2.1/2
63
2.1/2
63
385
850
Ordering
Nr.
Capacity (C)
Throat Depth (D)
Inch
mm
Inch
35820
15/16
24
1
mm
25
GCL/SM/2
35821
2
50
1
25
GCL/SM/2-1-2
35822
2.1/2
63
2.19/32
66
u
GCL/SM/3
35823
3
75
1.13/32
36
u
GCL/SM/4
35824
4
100
1.7/8
48
u
BESTSELLER
D
C
Cat. Nr.
forged
construction
UTILITY
UTILITY
industrial
CB 44
section 2
www.groz-tools.com
3
Handyman's Hacksaw 46 Hacksaw Frame - Professional 47
Universal Saw 48 Junior Saw Frame 49 Junior Saw - Baby Bite 49
Junior Saw Frames 50 Piercing Saw Frames 51 Coping Saw Frames 52
Fret Saw Frames 53 Hacksaw Blades 54 Piercing Saw Blades 54
Fret Saw Blades 55 Coping Saw Blades 55 Mini Saw Blades 56
CB 45
section 3
31 Handyman’s Hacksaw <HF 15>
espSierra bricolage
frScie bricolage
deMetallsägebogen
Cat. Nr.
uHF/15/BS
An adjustable frame with outstanding design and superior quality. The
rectangular section of the tubular bow ensures perfect combination of
rigidity and balance.The Aluminium die cast handle, unbreakable in normal
use provides a comfortable grip and also directs pressure in the correct line
of thrust for maximum efficiency
u
Ordering
Nr.
30010
BESTSELLER
Overall
Length (L)
Height (H)
Depth of
Bow (H)
Inch
mm
Inch
mm
Inch
mm
17
430
5.1/8
130
4.15/64
106
6000 PSI
420 Kgf/cm2
tensile
strength
The saw is adjustable for 10" (250 mm) & 12" (300 mm) blades. The blade
can additionally be set for sawing at 90o. A handy storage compartment in
the tubular bow allows for storing spare blades
The lightweight design of this saw makes it exceptionally useful for overhead
cutting or use from a ladder or scaffolding.
The saw comes complete with a 12" (300 mm) chrome steel hacksaw blade
UTILITY
metalworking
< HF/15/BS
HF/12/BC >
Adjustable for 10"(250mm)
& 12"(300mm) blade
Depth of
bow (h)
Height
(H)
Overall length (L)
CB 46
section 3
32 HacksawFrame—Professional <HF12>
espSierra profesional
frScie professionel
deMetallsägebogen
u
A rugged heavy-duty industrial quality hacksaw designed for the
professional. Strong aluminium die cast handle provides comfort and control
whilst the guarded grip design protects knuckles from grazing.
The tubular frame has a square section which provides the perfect
combination of balance and rigidity and a curved front end designed for
comfortable two hand usage. Easy to use blade tensioning device helps to
set the blade correctly.
The saw comes complete with a 12" (300 mm) chrome steel hacksaw blade
Cat. Nr.
Ordering
Nr.
Details
Overall
Length (L)
Height (H)
Depth of
Bow (h)
Inch
mm
Inch
mm
Inch
mm
HF/12/BC
30000
Chrome
Plated frame
with blue
handle
17.5/16
440
5.1/8
130
4
100
HF/12/RB
30001
Black frame
with red
handle
17.5/16
440
5.1/8
130
4
100
u
8000 PSI
BESTSELLER
560 Kgf/cm2
tensile
strength
UTILITY
metalworking
Depth of
bow (h)
Height
(H)
Overall length (L)
HF/12/RB >
CB 47
section 3
33 Universal Saw <UV-6>
espArco - Universal
frScie - Universel
deMetallsägebogen
Superior Quality Junior Saw –can be adjusted at any
position thus providing greater versatility in use
Wooden handle can be adjusted at any Position on
the plated steel frame by simply tightening the handle
at any point along the frame.
Very useful for working in confined spaces where
regular sawing is not possible.
The saw comes complete with a 6"(150mm) blade.
Cat. Nr.
Ordering
Nr.
Overall
Length (L)
Inch
JHF/UV/6
30140
12
mm
300
UTILITY
metalworking
Adjustablehandleallowsthesawtobeused
atoddanglesandinconfinedspaceswhere
regular sawing is not possible
CB 48
section 3
34 Junior Saw Frame <JHF 7>
35 Junior Saw — Baby Bite <P12>
espArco Sierra junior
frScie a decouper
deJunior-Metallsägebogen
espArco sierra junior
frScie a decoupes
de Junior -Metallsögebogen
An ideal saw for the DIY hobbyist. The frame is made from steel and has
a powder coated finish. Well designed plastic handle provides comfortable
grip. The saw comes complete with a 6" (150 mm) blade
This is a tough junior saw designed to provide the handyman and the
professional, the best means for coping with small sawing applications.
Cat. Nr.
JHF/7
Ordering
Nr.
30111
Overall
Length (L)
Height (H)
Depth of
Bow (h)
Inch
mm
Inch
mm
Inch
mm
11.3/16
284
3.3/8
85
2.3/4
70
The compact steel frame is light, yet strong and has a blade tensioning
device that locks when the correct blade tension is reached. Ergonomically
designed pistol grip handle is made from high quality ABS plastic and comes
in attractive colours. The saw comes complete with a 6" (150 mm) blade
Cat. Nr.
UTILITY
Ordering
Nr.
Details
JHF/P12/RD
30100
Red Handle
JHF/P12/GY
30101
Grey Handle
Overall
Length (L)
Height (H)
Depth of
Bow (h)
Inch
mm
Inch
mm
Inch
10
250
4
100
2
50
10
250
4
100
2
50
mm
metalworking
Depth of
bow (h)
Height
(H)
Overall length (L)
UTILITY
metalworking
< JHF/7
< JHF/P12/GY
< JHF/P12/RD
CB 49
section 3
36 Junior Saw Frames <JHF-4>
espArco Sierra junior
frScie a decouper
deJunior-Metallsägebogen
Superior quality steel wire frame is designed to ensure correct alignment
and give perfect blade tension during use. Blade holders intrinsic in the
frame avoid protrusion of the blade from the ends. Blade replacement is
simply by compressing the front end of the frame against any solid surface.
These are available in two types:
Junior Saw Frame — Powder Coated
u
Cat. Nr.
Ordering
Nr.
Overall
Length
Height
Depth of
Bow
Inch
mm
Inch
mm
Inch
JHF/4PD/BU
30130
10.3/8
260
2.3/4
70
2.3/8
60
JHF/4PD/GY
30131
10/38
260
2.3/4
70
2.3/8
60
245
2.3/8
60
2.1/8
53
mm
Junior Saw Frame — PLATED
u
JHF/4
u
BESTSELLER
30120
9.3/4
1. Junior Hacksaw Frame – Powder Coated: Steel wire frame has rust
inhibiting powder coated finish. Available in attractive blue or grey finish.
2. Junior Hacksaw Frame – Plated: Chrome plated steel wire frame has a
finger guard preventing injury to the user.
UTILITY
metalworking
< JHF/4
< JHF/4PD/BU
BluePowderCoated
< JHF/4PD/GY
GreyPowderCoated
CB 50
section 3
37 Piercing Saw Frames <PSF-8, PSF-A11>
espArcos joyero
frArc de scie pour metaux fins
deDurchstechendesägebogen
Piercing saws are used by skilled craftsmen in metalworking, jewellery and
dentistry applications for precision profile cutting of thin metals, plastics etc.
All piercing saw frames come fitted with piercing saw blades
1. Adjustable Piercing Saw Frame.
2. Deep Bow Piercing Saw Frame.
Adjustable Piercing Saw Frame <PSF-A11>
Adjustable Piercing Saw Frame Being adjustable for different blade lengths,
it is able to accommodate even broken blades thus extending blade life
Deep Bow Piercing Saw Frame <PSF-8>
Deep Bow Piercing Saw Frame Specially designed with a deeper bow,
allowing use on applications that require larger depth
Cat.
Nr.
UTILITY
Ordering
Nr.
Details
Overall
Length (L)
Height (H)
Depth of
Bow (h)
Inch
mm
Inch
mm
Inch
mm
PSF/A/11
30200
Adjustable
13
325 (Max.)
3.11/32
85
2.3/4
70
PSF/8
30201
Deep Bow
11.3/32
282
4.1/2
115
3.3/4
95
jeweller's
tool
Depth of
bow (h)
Height
(H)
Overall length (L)
PSF/A/11 >
Adjustable Piercing Saw Frame
Being adjustable for different blade
lengths, it is able to accomodate
even broken blades thus extending
blade life
PSF/8 >
Deep Bow Piercing Saw Frame
Specially designed with a deeper
bow, allowing use on applications
that require larger depth
CB 51
section 3
38 Coping Saw Frames <CSF-10>
espArcos sierra marqueteria
frScie maquettiste poignee bois
deStiftsägebogen
Cat. Nr.
An ideal saw for the
discerning craftsman and DIY
enthusiasts, the Coping Saw
is useful for cutting intricate
shapes in wood. Blade can be
turned to cut at any angle,
correct tension being applied
by turning the handle.
Ordering
Nr.
Details
Inch
mm
Inch
mm
Inch
mm
CSF/10
30200
Blue Powder
Coated Frame
12.3/4
320
5.7/16
136
5
125
u
CSF/10/CP
30221
Chrome Plated
Frame
12.3/4
320
5.7/16
136
5
125
u
BESTSELLER
Rigid and well balanced frame is available in a choice of
blue powder coated or premium chrome plated finish. Well
designed wooden handle provides comfortable grip.
Overall
Length (L)
Depth of
bow (h)
Height (H)
Depth of
Bow (h)
Height
(H)
The saw comes complete with a well set coping saw blade
UTILITY
Overall length (L)
woodworking
jeweller's
tool
VENEERS &
laminates
< CSF/10/CP
PIPES &
TUBES
1.
Loosen the handle
(Nut insert inside
the handle)
2.
Endsbecomeloose
Blade can be
turned to cut
at any angle
3.
Twist as you want
< CSF/10
CB 52
section 3
39 Fret Saw Frames <FSF-9>
espArco sierra materiales finos
frScie maquettiste acier
deLaubsägebogen
Cat. Nr.
Ordering
Nr.
Details
Inch
mm
Inch
mm
Inch
mm
FSF/9
30223
Blue Powder
Coated Frame
12
300
12
300
11.3/8
285
30222
Chrome Plated
Frame
12
300
12
300
11.3/8
285
This is an exceptionally rigid and well designed saw, very useful for fine
cutting work in most materials.
u
FSF/9/CP
The design of the bow allows the blade to be tensioned as it is clamped
in the frame. The serrated clamps operated via the screw and wing nut
maintain firm grip on the blade.
u
BESTSELLER
The Fret Saw is available in a choice of blue powder coated or premium
chrome plated finish. Well designed wooden handle provides comfortable
grip.
Overall
Length
Height
Depth of
Bow
UTILITY
woodworking
VENEERS &
laminates
PIPES &
TUBES
The saw comes complete with a standard fret saw blade.
FSF/9/CP >
FSF/9 >
CB 53
section 3
40 Hacksaw Blades <HB-C>
41 Piercing Saw Blades <PSB>
espSierras de mecanico
fr Lames pour scie
deHandsägeblättern
esp Hojas sierra metales finos
fr Lames pour scies metaux fins
deSageblättern
Manufactured from high grade chrome alloy steel, these are useful for light
and medium sawing work.
These are ideal for hand and light machine sawing of gold, silver, steel,
copper, brass, aluminium, nickel etc.
These are available in two lengths 10" (250 mm) and 12" (300 mm), both
with 18 TPI and 24 TPI.
Whilst designed for use with the Groz Piercing Saw Frames, these will also
conveniently fit onto standard Piercing Saw Frames of other makes. Overall
length 5" (125 mm).
Sold as a pack of 10 blades
Cat. Nr.
HB/C/01
Ordering
Nr.
Length
TPI (Threads
per inch)
30324
10" (250 mm)
18
Cat. Nr.
Ordering
Nr.
Blade Nr.
TPI (Threads
per inch)
HB/C/02
30325
10" (250 mm)
24
PSB/G2/0
30343
2/0
58
u
HB/C/03
30326
12" (300 mm)
18
PSB/G1/0
30344
1/0
58
u
HB/C/04
30327
12" (300 mm)
24
58-62
HRC
UTILITY
METALWORKING
PSB/G/0
30345
0
52
u
PSB/G/1
30346
1
48
u
PSB/G/2
30342
2
42
PSB/G/3
30347
3
42
PSB/G/4
30348
4
32
PSB/G/5
30349
5
32
PSB/G/6
30380
6
32
UTILITY
u
BESTSELLER
jeweller's
tool
Piercing Saw Blades
CB 54
section 3
42 Fret Saw Blades <FSB>
43 Coping Saw Blades <CSB>
espPelos de segueta
fr Lames pour scies metaux fins
deLaubsägeblättern
esp Hojas sierra marqueteria
fr Lames pour scies marqueterie
deStiftsägeblättern
These are ideal for hand and light machine sawing of wood, bone, vulcanite,
fibre, horn and plastics etc.
These are manufactured from high quality steel and are accurately heat
treated to give the correct combination of hardness and toughness. Teeth
are properly shaped set to ensure speed of cutting and ease of turning
Whilst designed for use with the Groz Fret Saw Frame these will also
conveniently fit onto standard Fret Saw Frames of other makes. Overall
length 5" (125 mm).
Cat. Nr.
u
u
Whilst designed for use with the Groz Coping Saw frames, these will also
conveniently fit onto Standard Coping Saw Frames of other makes.
Ordering
Nr.
Blade Nr.
TPI
(Threads per inch)
FSB/3
30357
3
18
FSB/4
30358
4
18
FSB/5
30359
5
16
FSB/6
30360
6
16
FSB/8
30361
8
14
FSB/10
30362
10
12
FSB/12
30363
12
10
Cat. Nr.
CSB/170
UTILITY
Length
TPI
(Threads per inch)
30314
6.1/2" (165mm)
14
UTILITY
woodworking
u
Ordering
Nr.
jeweller's
tool
BESTSELLER
woodworking
HacksawBlades
FretSawBlades
Coping Saw Blades
CB 55
section 3
44 Mini Saw Blades <MSB>
espSierras junior
fr Lames pour mini-scies
deSageblättern
Cat. Nr.
Standard 6"(150mm) long mini saw blades these are unbreakable in normal
use and provide a handy and efficient means for cutting metals and other
materials.
u
Available in 2 distinct types for metal cutting and wood cutting applications.
u
Metal Cutting Blades
Available in two types:
a) Shatterproof blades with hardened teeth
b) All hard blades
Wood Cutting Blades
Ordering
Nr.
TPI (Threads
per inch)
Specifications
MSB/55
30304
32
Shatterproof blades with hardened
teeth. Useful for all metal working
applications.
MSB/H/55
30303
32
All hard blades. Useful for all metalworking applications
MSB/WD/55
30305
14
Wood Cutting Blades
BESTSELLER
UTILITY
woodworking
METALWORKING
Useful for general purpose sawing especially on soft woods.
All are sold as a pack of 10 blades
MiniSawBlade-WoodCutting
MiniSawBlade-AllHard
MiniSawBlade-Shatterproof
CB 56
section 3
www.groz-tools.com
4
Bench Planes 58 Duplex Rabbet & Fillister Plane 60 Block Planes 61 Woodworking Vices Plain Screw 62 Woodworking Vice - Portable 63 Woodworking Vices - Quick Release 64
Woodworking Vices - Rapid Action 65 Woodworking Front Vice 66 Kwik Clamps Quick Action Woodworking Clamps 67 Rapid Action I Bar Clamps 68 Duo Bar
CB 57
section 4
45 Bench Planes <SP-3, SP-4, JP-5, FP-6, JP-7>
esp Cepillo de carpintero
frRabot
deBankhobel
Cat. Nr. Ordering
Nr.
Highest Quality Bench planes, engineered to exacting tolerances while
maintaining traditional standards of workmanship, design & performance
Groz planes have fine & robust Grey Cast Iron bases which are accurately
machined & ground to high precision. Sole is flat to 0.003"(0.075mm).
Spring steel cutter blade is hardened to 55 + 5 HRC and hones quickly to a
razor sharp, long lasting edge. Accurately machined blade seating eliminates
blade “chatter”. Fully adjustable frog provides the required setting for the
specific job.
Attractive hardwood handle and knob with brass adjusting nut and screw
heads makes this a favourite with the discerning woodworker
Type
Suitable
For
Length
Cutter Width
Inch
mm
Inch
mm
SP/3
39700
Smoothing
Plane
Final finishing
work
9.1/2
240
1.3/4
45
u
SP/4
39701
Smoothing
Plane
Final finishing
work
10.1/4
260
2
50
u
JP/5
39702
Jack Plane
For heavy
stock removal
when preparing
sawn timber prior
to final finishing
14
355
2
50
lFP/6
39703
Fore Plane
Used for flattening and smoothening wider
panels such as
table tops and
work bench tops
18
458
2.3/8
60
lJP/7
39704
Jointer Plane
Used for truing
up the edges of
long boards prior
to joining them
together to
create large
boards
22
560
2.3/8
60
u
BESTSELLER
l
NEW
JP/7 >
FP/6 >
CB 58
section 4
Cat. Nr. SP/4 - BP/605/ST
Ordering Nr. 39721
Set of Smoothing Plane #4 (SP/4)
andAdjustableMouthBlockPlane
(BP/605) in an attractive
blow moulded case
< JP/5
SP/4 >
SP/3 >
CB 59
section 4
46 DuplexRabbet&FillisterPlane <DRFP-78>
esp Cepillo de carpintero
frRabot
deSimshobel
Manufactured from high quality grey iron castings, the plane is used for
producing rabbeting cuts in doorframes, windows, furniture & cabinet
carcasses. Cuts rabbets both with & across the grain!
The plane has 2 positions for the cutter. The rear position for regular rabbet
work & the forward position for bull-nose work. When used in usual rear
position, the cutter is adjustable for depth of cut.
Cat. Nr.
uDRFP/78
u
Ordering
Nr.
39730
Length
Cutter Width
Inch
mm
Inch
mm
8.1/2
212
1.1/2
40
BESTSELLER
< Rabbet & Fillister Plane
The plane is fitted with:
Spur: Kept flush with the base when cutting with the grain. It is brought into
use by turning through 90˚ when cutting across the grain. The Spur in this
position prevents tearing & splintering of wood which otherwise would occur
when cutting across the grain.
Adjustable fence: Can be fitted on either side of the plane.
Depth gauge: Adjustable upto 1/2" (12mm). This also is removable
cuts rabbets both with and
across the grain
makes rabbet cuts in wood for
doorframes,windows,furniture
and cabinet carcasses
CB 60
section 4
47 Block Planes <BP-220, BP-605>
espRabot D' Ebeniste
fr Chanda de 1.5/8" de Cortè
deEinhandhobel
These are small planes especially useful for working on end grain of timber
& small-scale chamfering and planing jobs.
Cat. Nr.
Ordering
Nr.
Length
Cutter Width
Inch
mm
Inch
mm
Blade
Angle
BP/220
39791
7
180
1.5/8
42
21°
uBP/605
39790
6.1/4
160
1.3/8
35
13.1/2°
u
Type
Fixed Mouth
Adjustable Mouth
BESTSELLER
Robust grey cast iron bases are accurately machined and ground with
flatness of sole within 0.003" (0.075mm) . The plane iron is set at a low
angle to ensure efficient end grain planing jobs.
Block Planes are available in two types:
With Adjustable Mouth: Especially useful for cutting plastic laminate and
other man-made materials. The cutter is set at an angle of 13.1/2° and is fully
adjustable for depth of cut. Mouth is adjustable for coarse or fine work
With Fixed Mouth: General purpose block plane with screw for adjusting
depth of cut. The cutter is held rigidly by a knurled wheel and screw and set
at 21° angle
BP/220 >
<BP/605
CB 61
section 4
48 Woodworking Vices — Plain Screw <Series WWV & Series WWV/E>
Heavy Duty Full Size Workshop Vices <Series
WWV>
esp Tornillo de banco carpintero
frPresse d' etabli
deTischler-Schraubstock
Manufactured in 3 capacities, these full size vices have large jaw openings
These are manufactured from close-grained grey cast iron for long trouble
free service. Accurately machined housings assure smooth sliding movement.
Accurately fitted solid steel guide rods reduce wear and tear giving the vices a
smooth and true parallel action, free of side or cross deflection.
Vice jaws are equipped with a “TOE – IN” feature.
When fully closed, the jaws meet only at the top to
provide even clamping on the whole depth of the
work piece.
Square body seating provides easy fitment under
the bench top so that jaws are flush with the bench
top.
The steel main screw has Buttress threads for smooth, accurate and responsive
adjustment. Body and sliding jaw have provision for attaching wooden liners to
protect the vice, the work piece and working tools.
Cat.Nr.
WWV/150
u
Ordering
Nr.
39000
Jaw Width
Jaw Opening
Net Wt
Inch
mm
Inch
mm
kgs
6
150
4.1/2
115
2.300
WWV/175
39001
7
175
8
200
7.250
WWV/225
39002
9
225
13
330
13.750
Home Carpenter’s Vices <Series WWV/E>
A range of light weight vices for the amateur home carpenter or the young
woodworker, yet robust enough for the professional who needs a compact
vice for smaller work.
Cat.Nr.
1. Heavy Duty Full Size Workshop Vices <Series WWV>
2. Home Carpenter's Vices <Series WWV/E>
u
Ordering
Nr.
Jaw Width
Jaw Opening
Net Wt
Inch
mm
Inch
mm
kgs
WWV/EC/175
39004
7
175
6
150
2.5000
WWV/EC/225
39005
9
225
9
225
5.5000
BESTSELLER
Cast
< Heavy Duty Workshop Vice
CB 62
section 4
49 woodworkingvice—Portable <P-6>
esp Tornillo de banco carpintero - transportable
frPresse d' etabli
deTischler-Schraubstock
Vice jaws are equipped with a “TOE – IN” feature.
When fully closed, the jaws meet only at the top to
provide even clamping on the whole depth of the
work piece.
A useful, lightweight vice for the young woodworker or home handyman,
yet robust enough for professional use. The design allows for two clamping
options:
The steel main screw, guide rods and handle are
chrome plated for increased resistance to corrosion
a)Permanent clamping on the workbench via clamping slots provided in
the vice.
b)Additional clamping option via the 2.5/32"(55mm) integrated clamp.
This allows the vice to be conveniently clamped to any work surface.
Cat.Nr.
uWWV/P/6
u
Ordering
Nr.
39006
Jaw Width
Jaw Opening
Net Wt. each
Inch
mm
Inch
mm
kgs
6
150
4.1/2
112
2.750
BESTSELLER
Vice body and front plates are made from close grained cast iron. Body and
sliding jaw have provision for attaching wooden liners to protect the vice,
the work piece and working tools.
Cast
UTILITY
Additional
clamping option
via 2.5/32"(55mm)
integrated clamp
< Portable Vice
< Home Carpenter's Vice
CB 63
section 4
50 Woodworking Vices — Quick Release <DQ-7, DQ-9, DQ-11>
esp Tornillo de banco carpintero - rapida
frPresse d' etabli serrage rapide
de Tischler-Schraubstock mit Schnellverstellung
A traditional pattern woodworking vice equipped with the quick release
mechanism. Simply pressing the trigger initiates the quick action, with
the front jaw sliding freely, thereby allowing large or small work pieces to
be interchanged smoothly. Releasing the trigger returns the mechanism
to normal for fine adjustment. A very useful feature in repetitive work
situations.
feature. When fully closed the jaws meet only at the
top to provide even clamping on the whole depth of
the work piece.
The steel main screw has Buttress threads for smooth,
accurate and responsive adjustment. Body and
sliding jaw have provision for attaching wooden
liners to protect the vice, the work piece and working tools.
Cat.Nr.
Vices are equipped with an adjustable front dog which when used in conjunction
with a bench stop allows oversize work pieces too large to be held between the
jaws, to be securely held. This useful addition provides a normal vice and a tail vice
in one tool. Manufactured from close-grained grey cast iron, these robust vices
have accurately machined housings for smooth sliding movement and true parallel
action free of side or cross movement. Vice jaws are equipped with a “TOE – IN”
Ordering Nr.
Jaw Width
Jaw Opening
Net Wt
Inch
mm
Inch
mm
kgs
7
175
8
200
8.250
WWV/D/Q/7
39007
u
WWV/D/Q/9
39009
9
225
13.1/2
340
15.500
l
WWV/D/Q/10-1-2
39014
10.1/2
270
16
400
17.000
u
BESTSELLER
l
NEW
Cast
Vices are equipped
with an adjustable
front dog
Quick
Release
Trigger
< Quick Release Woodworking Vice
CB 64
section 4
51 Woodworking Vices — Rapid Action <R7, R9>
esp Tornillo de banco carpintero - rapida
frPresse d' etabli serrage rapide
de Tischler-Schraubstock mit Schnellverstellung
One of the most well designed vices by Groz, this one’s really brilliant. The
vice has a rapid action mechanism which is unique and different from the
conventional quick release mechanism. To tighten the vice, turn the handle
in the usual way. As soon as the handle is turned in the opposite direction,
the screw is disengaged and the front jaw slides freely. No springs, levers or
bars. A very useful feature in repetitive work situation for holding different
size pieces.
Manufactured from close grained grey cast iron these robust vices have
accurately machined housings for smooth sliding movement and true
parallel action free of side or cross movement.
Vice jaws are equipped with a “TOE – IN” feature
When fully closed, the jaws meet only at the top
to provide even clamping on the whole depth of
the work piece. The steel main screw has Buttress
threads for smooth, accurate and responsive
adjustment. Body and sliding jaw have provision for
attaching wooden liners to protect the vice,work piece and working tools
Cat.Nr.
Ordering
Nr.
Jaw Width
Jaw Opening
Net Wt
Inch
mm
Inch
mm
kgs
WWV/R/7
39011
7
175
8
200
7.250
u
WWV/R/9
39012
9
225
13
330
13.750
u
BESTSELLER
Cast
< Rapid Action Woodworking Vice
Rapid
release via
counter
clockwise
rotation
CB 65
section 4
52 Woodworking Front Vice <F7>
esp Tornillo de banco Carpintero
frPresse Horizontale pour Etabli
deVorderzangenführung
Front Vices are used by wood-workers wanting to make their own vice
assemblies and on work benches.
Strong and robust casting, cast iron handle socket, precision rolled threads
and twin guides, these are exceptionally sturdy, very easy to use and
distortion free. Vices come complete with a well finished wooden handle
Cat.Nr.
WWV/F/7
CB 66
Ordering
Nr.
39020
Jaw Width
Jaw Opening
Inch
mm
Inch
mm
7
175
8.3/4
255
section 4
53 KWIK Clamps — Quick Action Woodworking Clamps <Series KBC>
espAprieto carpintero - rapida
frSerre-Joint
deKorpuszwinge
Cat. Nr.
KBC/12
u
These quick action clamps are by far amongst the most
convenient, strong & accurate. These clamps have the quickest
adjustment mechanism - simply lifting the Aluminium die-cast
handle allows the sliding jaw to be moved anywhere on the rail.
u
u
Ordering
Nr.
Clamping Capacity
39180
Inch
mm
12
300
KBC/24
39181
24
600
KBC/31
39182
31
775
KBC/40
39183
40
1000
KBC/50
39184
50
1250
BESTSELLER
The rail is made from special "K" section steel profiled to
minimize flexing & bending. The steel rails have serrations
that engage with a hardened steel insert in the moving jaw to
eliminate slippage. Four hardened rollers in the moving head
maintain a constant 90° angle under load, ensuring that the
clamp heads remain parallel to each other & at right angles to
the rail at all times. The clamp jaws are encased in non-marring,
glue resistant polypropylene casing.
section
1.1/8"(29mm) x 3/8"(9mm)
x 1/4"(6mm)
Th
3.11 roat De
p
/32"
(85mth:
m)
Width of
clamp
face:
1.7/16"
(37mm)
5/8" (16 mm)
The clamp can be hand
tightened upto clamping
pressure of 2500 KN &
remains perfectly square
to the rail
The clamp is fitted with
a plastic end stop to
maintain it at level. By
removing this end stop,
the movable jaw can be
reversed and be used as
a spreader - very useful
inbuildingwindow&door
frames
CB 67
<QuickAction
Clamp as a
spreader
section 4
54 Rapid Action I Bar Clamps <No. 391 I>
esp Viguetas perfil "I" - rapida
frEtaux reglable en forme I - rapide
deSchnellschraubzwingen
A Rapid action I section Bar clamp designed and manufactured for hard,
everyday production jobs.
I Section drawn bars are rolled dead straight with quick action non-slip
clutches on side faces at intervals of 3/4"(19mm). Head and tail piece made
from virtually unbreakable 60,000 PSI SG Iron (Ductile Iron).
Movable head has a lock lever mechanism - A simple press of the lever
allows quick opening: closing is simply by pushing the movable head to
required position. Main Screw & handle are made from high-grade steel with
rolled threads for wear resistance.
Cat. Nr.
Ordering
Nr.
Bar Length
Capacity
Inch
mm
Inch
mm
600
IBC/T/2
39160
30
750
24
IBC/T/2-1-2
39161
36
900
30
750
u
IBC/T/3
39162
42
1050
36
900
u
IBC/T/4
39163
54
1350
48
1200
u
IBC/T/5
39164
66
1650
60
1500
IBC/T/6
39165
78
1950
72
1800
u
BESTSELLER
I section
1.1/2"(38mm)x13/32"(10mm)
x 3/16"(4.5mm)
Superior strength combined with the convenient to use rapid action
mechanism & large clamping faces makes these a real favourite with the
user.
Load Capacity: 6000 lbs (2700 kg)
Widthof
Clamp
Face:
1.7/8"
(47mm)
mm)
/16" (46
pth: 1.13
e
D
t
a
ro
Th
5/8"
(16mm)
Simple press of the
lever allows quick
opening. Closing is by
pushing the movable
head to the required
position
CB 68
section 4
55 Duo Bar Clamps <No. 391 D>
56 Cramp head set
esp Viguetas - doble accion
frEtaux menuisier action libre
deSchnellschraubzwingen - Doppelte Handlung
esp Tornillos de apriete des montable
frSerre-joint tetes mobiles
deSpannelement
Incorporating advanced features to the traditional Sash Cramp, the DUOBAR
is every woodworker’s delight. Rigid and robust malleable iron head and
slide can be easily reversed on the bar allowing both internal as well as
external clamping.The spring loaded pin allows the head and slide to be
adjusted at any desired position on the bar. Internal clamping is especially
useful for holding window or door frames in position or holding partioning
in place during construction etc. Bars made from drawn steel with a section
of 1.1/4" x 1/4" (32 mm x 6 mm) are furnished with holes equally spaced
along the entire length for clamping of a vast range of sizes. The enhanced
features of this set of cramps allows the user greater flexibility. Just one set
of head and slide and a range of bars makes for a complete clamping kit.
Cramp heads are a low cost alternative to the full size T Bar and Sash Bar
Cramps. A bar cramp of any length can be made by using a piece of timber
1"(25mm) thick. The timber is drilled with holes producing a light duty bar
cramp as strong and as true as the timber chosen. The heads are made
from malleable iron, the handle screw and pin from high quality steel for
hard wearing long life. Blackened screw has rolled threads for extra strength
and resistance to wear.
Cat. Nr.
Ordering
Nr.
Bar Length
mm
Ordering Nr.
39120
External Capacity
Inch
mm
DBC/24
39130
24
600
18
450
DBC/30
39131
30
750
24
600
u
DBC/36
39132
36
900
30
750
u
DBC/42
39133
42
1050
36
900
u
DBC/48
39134
48
1200
42
1050
DBC/54
39135
54
1350
48
1200
u
Inch
Cat. Nr.
CHST/25-25
BESTSELLER
rectangular section
1.1/4"(32mm) x 1/4"(6mm)
Duo Bar DoubleAction
Sash Cramp:
Internal
Clamping
1/2"
(12mm)
Width of
Clamp Face:
1.3/16"
(30 mm)
5mm)
:2.1/8"(5
th
p
e
D
Throat
Duo Bar Double Action
Sash Cramp:
External
Clamping
CB 69
section
4
CB 69
57 Sash Bar Clamps <No. 391 S>
58 T Bar Clamps <No. 391 T>
espViguetas
frEtaux menuisier
esp Viguetas perfil "T"
frEtaux reglable en forme T
These Bar Cramps are especially useful for clamping large section
workpieces during fabrication,gluing in joinery, carpentry and boat building.
The bars are made from drawn steel with a section of 1.1/4" x 1/4" (32 mm
x 6 mm).Malleable iron head and slides provide rigidity and strength even
under heavy tension. Both head and slide have a flat bottom allowing the
bar to stand upright without support. The head is fitted square to the bar
with 1.1/2° - 2° taper for true parallel clamping action.
A robust set of clamps designed for applications that require extra
resilience under extreme pressure, these can be permanently fixed onto the
workbench as well. The “T” section bar is made from special cold drawn
steel with a section of 1" x 1.5/8" which offers great resistance to bending
in use. Malleable iron head and slide allow these clamps to be used in
extra heavy duty applications. The main screw has rolled Acme threads for
smooth movement and increased resistance to wear. The sliding head is
fastened to the T Bar by inserting a steel pin through any of the locating
holes on the bar. The steel bar,head and slide have an attractive powder
coated finish, the main screw,handle and pins are blackened for increased
resistance to corrosion.
Main screw and handle are made from high-grade steel and have a
blackened finish for increased resistance to corrosion.The screw has rolled
Acme threads that impart extra strength and are wear resistant.
Throat Depth: 1.7/8" (48 mm)
Width of Clamp Face: 2.1/8" (54 mm)
Throat Depth: 2" (50 mm)
Width of Clamp Face: 1.3/16" (30 mm)
Cat. Nr.
Cat. Nr.
SBC/24
Ordering
Nr.
39110
Bar Length
Capacity
Inch
mm
Inch
mm
24
600
18
450
Ordering
Nr.
Bar Length
Capacity
Inch
mm
Inch
mm
TBC/3
39100
36
900
30
750
u
TBC/4
39101
48
1200
42
1050
SBC/30
39111
30
750
24
600
u
TBC/5
39102
60
1500
54
1350
u
SBC/36
39112
36
900
30
750
u
TBC/6
39103
72
1800
66
1650
u
SBC/42
39113
42
1050
36
900
TBC/7
39151
84
2100
78
1980
u
SBC/48
39114
48
1200
42
1050
SBC/54
39115
54
1350
48
1200
u
BESTSELLER
T section
1.7/8"(48mm) x 7/8"(22mm)
rectangular section
1.1/4"(32mm) x 1/4"(6mm)
Width of
Clamp Face
1.3/16"
(30 mm)
< Sash Bar Cramp
Throat Depth
2" (50 mm)
Throat Depth
1.7/8" (48 m
m)
Width of
clamp
face
2.1/8"
(54 mm)
T Bar Cramp >
CB 70
section 4
www.groz-tools.com
5
Spring Calipers & Dividers 72
Craftsmen's Spring Calipers & Dividers 73
Wing Compass 74 Adjustable Bevel 74
Centre Square 75 Precision Squares 75
CB 71
section 5
59 Spring Calipers & Dividers <No. 014>
esp Calibradores & divisores muelle
fr Compas et diviseurs A ressort
deFeder-Spitzzirkel und Spitzzirkel
Amongst the oldest comparative measuring tools, Calipers are designed
for taking transfer measurements or for comparing external and internal
measurements. Dividers are used for marking on steel or for transferring
measurements from master templates.Divider points are hardened for
increased wear resistance
Manufactured from high grade steel with a polished finish, the legs pivot
on a roller and are tensioned by a bow spring. Measuring adjustment is via
an adjusting nut that allows fine settings. Measuring capacity/ Size is the
distance between the fulcrum and the end of the leg.
1. With Solid Nut.
2. With Quick Nut - the threads of the
split quick adjusting nut engage the
screw at the slightest pressure of the leg
and when the pressure is withdrawn, the
nut releases itself sliding freely over the
screw. This feature helps save valuable
time in opening & closing when a variety
of measurements have to be taken
consecutively
Cat. Nr.
Ordering Nr.
With Solid Nut
Cat. Nr.
Ordering Nr.
With Quick Nut
Size
Inch
mm
Inside Calipers
ID/3
01400
ID/Q-3
01430
3
75
u
ID/4
01401
ID/Q-4
01431
4
100
u
ID/6
01402
ID/Q-6
01432
6
150
u
ID/8
01403
ID/Q-8
01433
8
200
ID/10
01404
ID/Q-10
01434
10
250
ID/12
01405
ID/Q-12
01435
12
300
Outside Calipers
OD/3
01410
OD/Q-3
01440
3
75
u
OD/4
01411
OD/Q-4
01441
4
100
u
OD/6
01412
OD/Q-6
01442
6
150
u
OD/8
01413
OD/Q-8
01443
8
200
OD/10
01414
OD/Q-10
01444
10
250
OD/12
01415
OD/Q-12
01445
12
300
Spring Dividers
DD/3
01420
DD/Q-3
01450
3
75
u
DD/4
01421
DD/Q-4
01451
4
100
u
DD/6
01422
DD/Q-6
01452
6
150
u
DD/8
01423
DD/Q-8
01453
8
200
DD/10
01424
DD/Q-10
01454
10
250
DD/12
01425
DD/Q-12
01455
12
300
u
BESTSELLER
UTILITY
metalworking
CB 72
woodworking
size
section 5
60 Craftsmen’s Spring Calipers & Dividers
esp Calibradores & divisores muelle - Premium
fr Compas et diviseurs A ressort - premium
deFeder-Spitzzirkel und Spitzzirkel
These are amongst the finest calipers and dividers, especially useful for
the discerning craftsmen. Made from high grade steel, legs are machined
to a smooth taper with an attractive black powder coated finish. The finely
machined and polished nut runs smoothly to secure the legs exactly to
dimension. Truly, every woodworker’s delight, these are available individual
or as a set.
1. With Solid Nut
2. With Quick Nut - the threads of the
split quick adjusting nut engage the
screw at the slightest pressure of the leg
and when the pressure is withdrawn, the
nut releases itself sliding freely over the
screw. This feature helps save valuable
time in opening & closing when a variety
of measurements have to be taken
consecutively
Cat. Nr.
Ordering Nr.
Solid Nut
Cat. Nr.
Ordering Nr.
With Quick Nut
Size
Inch
mm
Inside Calipers
ID/SP/3
01460
ID/SP/Q-3
01560
3
75
ID/SP/4
01461
ID/SP/Q-4
01561
4
100
uID/SP/6
01462
ID/SP/Q-6
01562
6
150
uID/SP/8
01463
ID/SP/Q-8
01563
8
200
ID/SP/10
01454
ID/SP/Q-10
01564
10
250
ID/SP/12
01455
ID/SP/Q-12
01565
12
300
OD/SP/3
01470
OD/SP/Q-3
01570
3
75
OD/SP/4
01471
OD/SP/Q-4
01571
4
100
uOD/SP/6
01472
OD/SP/Q-6
01572
6
150
uOD/SP/8
01473
OD/SP/Q-8
01573
8
200
OD/SP/10
01474
OD/SP/Q-10
01574
10
250
OD/SP/12
01475
OD/SP/Q-12
01575
12
300
DD/SP/3
01480
DD/SP/Q-3
01580
3
75
DD/SP/4
01481
DD/SP/Q-4
01581
4
100
uDD/SP/6
01482
DD/SP/Q-6
01582
6
150
uDD/SP/8
01483
DD/SP/Q-8
01583
8
200
DD/SP/10
01484
DD/SP/Q-10
01584
10
250
DD/SP/12
01485
DD/SP/Q-12
01585
12
300
CD/SP/ST-6
01492
A set of one each : 6"(150mm) Inside & Outside
Calipers & Springs Dividers
uCD/SP/ST-8
01494
A set of one each : 8"(200mm) Inside & Outside
Calipers & Springs Dividers
Outside Calipers
Spring Dividers
UTILITY
Sets
metalworking
woodworking
u
BESTSELLER
size
CD/SP/ST-6
A set of one each : 6"(150mm)
Inside & Outside Calipers &
Springs Dividers
CB 73
section 5
61 WingCompass <WC-6,WC-8,WC-16>
62 Adjustable Bevel <AB 10>
espBrújula
fr Compas de Menuisier 1/4 circle
deSpitzzirkel
esp Bisel regulable
frFausse equerre de menuisier
deSchmiegen
These rugged industrial grade compasses are manufactured from heavy
gauge steel with an attractive black powder coated finish. The tip is
accurately ground. Heavy Duty hinge and knurled locking nut help in
convenient movement.
These bevels are especially useful for marking dovetails and other unusual
angles.The offset slot in the blade enables a line to be drawn along the full
length of the blade without interference from stock.
Used for precisely scribing arcs and circles on projects and drawings.
Cat. Nr.
Ordering
Nr.
Size
Scribing Capacity
Inch
mm
WC/6
01551
6
150
8
200
uWC/8
01553
8
200
10.1/2
265
01554
16
400
22
550
WC/16
The polished wooden handle is fitted with thick brass fittings which protect
the ends from damage.Blade adjustment is achieved via a forged steel
wingnut.
Inch
mm
u
BESTSELLER
Cat. Nr.
AB/10
Ordering
Nr.
39400
Size
Inch
mm
10
250
UTILITY
UTILITY
woodworking
woodworking
CB 74
section 5
63 Centre Square <CS-1, CS-2>
64 Precision Squares
espEscuadra centrador
frEsquerres pour centrer
deZentrierwinkel
espEscuadras precision
frEsquerres de precision
dePräzisions Zimmermanns Haarwinkel
An extremely useful tool for locating centers of round stocks and parts,
quickly and easily. The knife edge blade is made from spring Steel, hardened
and ground for extended life
An excellent range of Steel Squares with accuracies conforming to BS 939
grade B for squareness. Blades are made from hardened spring steel
with both stock and blade precisely ground to ensure straightness and
parallelism. These are very useful for woodworkers and cabinet makers and
are of particular value when setting up power tools
Cat. Nr.
Ordering
Nr.
Size
Inch
mm
CS/1
03521
1.1/2
38
uCS/2
03522
3
75
u
Cat. Nr.
Ordering
Nr.
BESTSELLER
Accuracy for
Internal
and external
Squareness
Inch
mm
Inch
mm
Inch
Microns
01000
2
50
2
50
0.00063
16
SS/A/3
01001
3
75
2.3/8
60
0.00063
16
uSS/A/4
01002
4
100
3
75
0.00063
16
uSS/A/6
01003
6
150
4
100
0.00063
16
SS/A/8
01004
8
200
5
125
0.00063
16
SS/A/9
01005
9
225
6.5/16
160
0.00094
24
SS/A/10
01006
10
250
6.1/2
165
0.00094
24
SS/A/12
01007
12
300
8.9/32
210
0.00094
24
METALworking
Position the vee of the center
square onto the round face
of the stock and scribe a
line along the knife edge.
Rotate the square and repeat
process.The common point of
intersection is the center of
the stock
Stock Length
(From edge of
stock to outer
edge
of blade)
SS/A/2
UTILITY
woodworking
Blade Length
(From inner
edge of
stock to end
of blade)
Sets
uSS/A/2-4-6
SS/A/2-3-4-6
u
01012
Set contains one each of 2"(50mm), 4"(100mm) &
6"(150mm) Squares
01011
Set contains one each of 2"(50mm), 3"(75mm), 4"(100mm)
& 6"(150mm) squares
BESTSELLER
SS/A/2-4-6
blade length
Set contains one each of
2"(50mm), 4"(100mm) &
6"(150mm) Squares
UTILITY
woodworking
METALworking
stock length
CB 75
section 5
65 Brass Calipers
66 Steel Rules
esp Calibradores de laton
fr Compas en laiton
deMessingtastzirkel
espReglas de acero
frRegles d' acier
deStahlmaßstäbe
A handy pocket caliper, made from solid brass. Close tolerance dovetail
design ensures smooth motion of the caliper and provides accurate
measurements. Graduated in both imperial and metric graduations with a
least count of 1/16" on the imperial scale and 0.1 mm on the metric scale,
these are ideal for use by mechanics, hobby crafters etc. who need to take
measurements on small objects such as nails, screws, lenses, tubing etc.
Made from stainless steel, these rules have a polished finish with
permanently engraved clear to read graduations.
1. Brass Calipers (Outside)
2. Brass Calipers (Inside and Outside)
Imperial & Metric combined rules: These rules are graduated in metric
dimensions on one edge and imperial on the other.Imperial dimensions are
in 1/16th , 1/32nd & 1/64 ths. Metric dimensions are in 0.5mm & mm. Reverse
side of the rule has a permanently engraved metric to imperial conversion
table.
1) Brass Calipers (Outside) — Used for making external measurements from
zero to the measuring range of the caliper.
2) Brass Calipers (Inside and Outside) — Used for making both internal and
external measurements. External measurements can be made from 0 - 4"
(0 - 100 mm), whereas internal measurements can be made from 7/32"
(5 mm) to 4" (100 mm)
Cat. Nr.
Ordering Nr.
Measuring Range
Inch
1. Imperial& Metric Combined Rules
2. Metric Rules
Metric rules: Graduated in metric dimensions 0.5mm & mm on both edges
Cat. Nr.
Imperial
& Metric
Ordering Nr.
Imperial
& Metric
Cat. Nr.
Metric
Ordering Nr.
Metric
Inch
mm
uSR/6
01330
SR/150
01340
6
150
uSR/12
01331
SR/300
01341
12
300
SR/18
01332
SR/450
01342
18
450
SR/24
01333
SR/600
01343
24
600
uSR/40
01334
SR/1000
01344
40
1000
SR/48
01335
SR/1200
01345
48
1200
mm
Brass Calipers - Outside
BC/ORD-75
01300
0-3
0-75
uBC/ORD-100
01301
0-4
0-100
BC/ORD-150
01302
0-5
0-150
Outside: 0-4
Inside: 7/32-4
0-100
5-100
u
Brass Calipers - Inside & Outside
BC/ORD/ID-100
01304
Length
BESTSELLER
Brass Calipers - Outside
UTILITY
woodworking
Brass Calipers - Inside & Outside
Steel Rules
CB 76
section 5
www.groz-tools.com
6
Adjustable Tap & Reamer Wrenches - Bar Type 78
Tap Wrenches - T Handle Type 79
Die Stock Holders For Round Dies 80
Tap & Die Sets 81 Hand Taps - Carbon Steel 82
CB 77
section 6
67 Adjustable Tap & Reamer Wrenches — Bar Type <No. 092D, 092R, 092>
esp Giramachos Adjustables
frTourne-a-gauche
de Verstellbare Windeisen
Cat. Nr.
Ordering
Nr.
Length
Jaw Holding Capacity
Square Size
Inch
mm
Inch
mm
Tap Size
Inch
mm
M2-M6
Acc DIN 1814
The straight handle design of these tap wrenches provides
greater leverage, particularly useful when working with large
diameter taps.
These are manufactured in three types.
Type A: Acc DIN 1814 <No. 092D>
Type B: Professional Quality <No. 092R>
Type C: Industrial Quality <No. 092>
Type A: Acc DIN 1814 <No. 092D>
With zinc die cast body and hardened steel jaws, these have an
exceptionally rugged construction. Chrome plated handles with
knurled ends provide a comfortable non slip grip. Larger sizes
have a cross hole drilled on one end for easy tightening using a
tommy bar.
Type B: Professional <No. 092R>
Professional quality tap wrenches with an all steel body, these
provide a positive grip combined with the sensitivity required
when tapping a blind hole. Jaws are hardened and tempered for
increased resistance to wear. The wrench body is black powder
coated with attractive chrome plated handles.
ATWR/D-0
09200
6.19/64
160
5/64-13/64
2-5
1/16-1/4
u
ATWR/D-1
09201
7.5/64
180
5/64-1/4
2-6.3
1/16-5/16
M2-M8
u
ATWR/D-2
09202
11
280
5/32-23/64
4-9
3/16-9/16
M5-M14
ATWR/D-3
09203
15
375
3/16-15/32
4.9-12
1 /4-3/4
M6-M18
M3-M5
Professional
ARWR/1-SPL
09210
5
125
7/64-5/32
2.5-4
1/8-3/16
u
ARWR/2-SPL
09211
8.17/64
210
1/8-1/4
3.15-6.3
3/16-5/16
M4-M8
u
ARWR/3-SPL
09212
12.13/64
310
1/8-3/8
3.15-9.5
3/16-9/16
M4-M14
ARWR/44-SPL
09213
16
400
7/32-5/8
5.6-16
7/16-1.1/8
M7-M27
M1-M12
Industrial
ARWR/SG/0
09221
8
200
5/64-21/64
1.77- 8.49
1/8-3/8
ARWR/SG/00
09220
4.88
122
1/16-13/64
1.42-5.19
1/8-1/4
M1-M6
ARWR/SG/5
09222
10.8
270
1/8-25/64
3.00-10.18
3/16-5/8
M4-M16
ARWR/SG/6
09223
14.8
370
1/8-31/64
3.00-12.5
3/16-7/8
M4-M20
ARWR/SG/7
09224
19.6
490
13/64-41/64
4.8-16.5
1/4-1/8
M6-M30
ARWR/SG/8
09225
29.6
740
17/64 - 1
6.5-25.4
1/2-1.3/4
M9-M45
u
BESTSELLER
UTILITY
metalworking
Type C : Industrial <No. 092>
Extra heavy duty, industrial quality tap wrenches - virtually
unbreakable. Nr. 0, 00, 5 & 6 have a forged steel body. Nr. 7 & 8
are cast from S.G.Iron
<TypeA:AccDIN1814
< Type B: Professional
< Type C: Industrial
Square
Size
CB 78
section 6
68 Tap Wrenches - T Handle Type <No. 093, 093R>
esp Giramachos en T
frPorte - tarauds en bout
deWerkzeughalter
Cat. Nr.
Ordering
Nr.
Overall
Length (L)
Inch
mm
Jaw Holding Capacity
Square Size
Tap Size
Inch
mm
Inch
mm
Regular
This range of tap wrenches are ideal for holding taps, reamers, screw
extractors and other such small hand turned tools. All wrenches have a
sliding T handle frictionally held, that allows these tap wrenches to be used
even in confined spaces.
TW/3-16
09300
2.23/64
60
5/64 – 5/32
2–4
1/16 – 3/16
M2 – M5
TW/1-4 SPL
09301
2.3/4
70
5/64 – 13/64
2–5
1/16 – 1/4
M2 – M6
09302
2.3/4
70
1/8 – 13/64
3.15 – 5
5/32 – 1/4
M4 – M6
09303
3.9/64
80
5/32 – 1/4
4 – 6.3
3/16 – 5/16
M5 – M8
09304
3.35/64
90
13/64 – 5/16
5–8
1 /4 – 1/2
M6 – M10
uTW/R/1-4
09320
3.3/8
86
7/64 – 7/32
2.6 – 5.5
5/32 – 1/4
M4 – M6
uTW/R/5-16
09321
4.3/8
111
3/16 – 5/16
4.6 – 8
1/4 – 1/2
M6 – M12
uTW/1-4
TW/5-16
uTW/1-2
1. Regular T Handle Type <No. 093>
2. Ratchet Type <No. 093R>
Regular T Handle Type <No. 093>
Ratchet Type
u
BESTSELLER
UTILITY
Self-centering hardened steel jaws provide a positive grip on taps, reamers
and other such small tools.
Ratchet Type <No. 093R>
These tap wrenches have self centering hardened steel jaws and knurled
chuck sleeve, which provide positive grip on taps, reamers and other such
small tools. The ratchet can be set left or right, or direct engagement in
neutral position. This feature allows them to be used in confined areas with
ease
metalworking
<RatchetType
<RegularType
Square
Size
CB 79
section 6
69 Die Stock Holders for Round Dies
espPorta terrajas
frPorte - filleres
deSchneideisenhalter
Cat. Nr.
Ordering
Nr.
Suitable For Die Size
Length
DS/D/20-5
09100
20x5
DS/D/20-7
09101
20x7
200 mm
DS/D/25-9
09102
25x9
224 mm
DS/D/30-11
09103
30x11
280 mm
DS/D/38-14
09104
38x14
315 mm
DS/13-16
09110
13/16"
6.1/2"
DS/0-1
09111
1"
8.1/4"
DS/1-5-16
09112
1.5/16"
10"
DS/1-1-2
09113
1.1/2"
12.3/8"
15.3/8"
mm
Acc Din 225
This range of die holders is best suited for applications requiring
efficient and clean cutting of external threads. Die holders have a rugged
construction with heavy duty set screws that hold the die firmly in place.
These are manufactured in two types:
Type A: Acc DIN 225
Type B: Professional Quality
Type A: Acc DIN 225
u
u
Professional
u
u
u
These have steel bodies with chrome plated handles.
Type B: Professional
This range of die holders have an all steel construction with black powder
coated body. Handles have knurled ends, the ends being black powder
coated.
200 mm
u
DS/0-2
09114
2"
DS/2-1-2
09116
2.1/2"
19"
DS/0-3
09117
3"
22.1/2"
DS/3-1-2
09118
3.1/2"
29.3/4"
DS/0-4
09119
4"
33"
BESTSELLER
UTILITY
metalworking
AccDIN225>
Professional >
CB 80
section 6
70 Tap & Die Sets
esp Juego giramachos & portacojinetes
fr Coffret tarauds et filieres
deGewindeschneidzeug-Sätze
Cat. Nr.
TDE/ST-1
Ordering Nr.
10000
Constituets
21 pcs Metric Tap & Die Set
Bar Type Tap Wrench 2 mm - 6.3 mm
Bar Type Tap Wrench 4.9 mm - 12 mm
Die Holders for Round Dies of dia. 1"
Die Holders for Round Dies of dia. 1.1/2"
A complete range of taps and dies alongwith suitable tap wrenches and die
holders packed in strong, attractive and convenient to store boxes. Contents
are housed in a well fitted inserts.
8 Round Dies:
6mm , 8mm, 10mm, 12mm,
14mm, 16mm, 18mm, 20mm
8 Metric Tap Sets:
6mm , 8mm, 10mm, 12mm,
14mm, 16mm, 18mm, 20mm
TDE/ST/41/M/ST>
TDE/ST-41I
110015
41 pcs Tap & Die Set
T handle Tap Wrench 0 - 1/4"
T handle Tap Wrench 1/4" - 1/2"
Bar Type Tap Wrench 0 - 1/2"
Die Holders for Round Dies of dia. 13/16"
Thread Pitch Gage (18 leaves, #8 to #44)
17 individual Hand Taps & Round Dies in sizes:
4-40 NC, 6-32 NC, 8-32 NC, 10-24 NC, 10-32 NF, 12-24
NC, 1/8"-27 NPT, 1/4"-20 NC, 1/4"-28 NF, 5/16"-18 NC,
5/16"-24 NF, 3/8"-16 NC, 3/8"-24 NF, 7/16"-14 NC,
7/16"-20 NF, 1/2"-13 NC, 1/2"-20 NF
TDE/ST-41M
10015
41 pcs Metric Tap & Die Set
T handle Tap Wrench 0 - 1/4"
T handle Tap Wrench 1/4" - 1/2"
Bar Type Tap Wrench 0 - 1/2"
Die Holders for Round Dies of dia. 13/16"
Thread Pitch Gage (16 leaves, 0.35mm to 3mm)
17 individual Hand Taps & Round Dies in sizes:
3mm - 0.50mm, 4mm - 0.70mm, 4mm - 0.75mm,
5mm - 0.80mm, 5mm - 0.90mm, 6mm - 1.00mm,
7mm - 1.00mm, 8mm - 1.00mm, 8mm - 1.25mm,
9mm - 1.00mm, 9mm - 1.25mm, 10mm - 1.25mm,
10mm - 1.50mm, 11mm - 1.50mm, 12mm - 1.50mm,
12mm - 1.75mm, 1/8" - 28mm BSP
UTILITY
metalworking
< TDE/ST-1
CB 81
section 6
71 Hand Taps - Carbon Steel
espRoscas de macho
frTarauds
deHandgewindebohrer
British StandardWhitworth (BSW) 55° - Set of 3
Nominal
Size
Cat. Nr.
TPI
(Thread
per Inch)
Nominal
Size
Inch
Taps are used for cutting internal threads in
predetermined holes.These perform best in
materials where the cutting action results in
chips which break up readily and do not present
problems of chip disposal. Taps are usually used
in sets of 3 (taper,second and bottom).
Taper
Used to provide a quick & easy start, but
this will not cut the thread down to the
bottom of the hole.
Second
Inch
60
3/16
TAP/BSF/3-16
09800
32
3/32
TAP/3-32
09401
48
7/32
TAP/BSF/7-32
09801
28
1/8
TAP/1-8
09402
40
1/4
TAP/BSF/1-4
09802
26
5/32
TAP/5-32
09403
32
9/32
TAP/BSF/9-32
09803
26
3/16
TAP/3-16
09404
24
5/16
TAP/BSF/5-16
09804
22
7/32
TAP/7-32
09405
24
3/8
TAP/BSF/3-8
09805
20
1/4
TAP/1-4
09406
20
7/16
TAP/BSF/7-16
09806
18
9/32
TAP/9-32
09407
20
1/2
TAP/BSF/1-2
09807
16
5/16
TAP/5-16
09408
18
9/16
TAP/BSF/9-16
09808
16
3/8
TAP/3-8
09409
16
5/8
TAP/BSF/5-8
09809
14
7/16
TAP/7-16
09410
14
11/16
TAP/BSF/11-16
09810
14
1/2
TAP/1-2
09411
12
3/4
TAP/BSF/3-4
09811
12
9/16
TAP/9-16
09412
12
13/16
TAP/BSF/13-16
09812
12
5/8
TAP/5-8
09413
11
7/8
TAP/BSF/7-8
09813
11
TAP/11-16
09414
11
15/16
TAP/BSF/15-16
09814
11
TAP/3-4
09415
10
1
TAP/BSF/0-1
09815
10
TAP/13-16
09416
10
1.1/8
TAP/BSF/1.1/8
09816
9
TAP/7-8
09417
9
1.1/4
TAP/BSF/1.1/4
09817
9
TAP/15-16
09418
9
1.3/8
TAP/BSF/1-3-8
09818
8
TAP/0-1
09419
8
1.1/2
TAP/BSF/1-1-2
09819
8
1.1/8
TAP/1-1-8
09420
7
1.3/4
TAP/BSF/1-3-4
09820
7
1.1/4
TAP/1-1-4
09421
7
2
TAP/BSF/0-2
09821
7
1.3/8
TAP/1-3-8
09422
6
1.1/2
TAP/1-1-2
09423
6
1.3/4
TAP/1-3-4
09424
5
TAP/0-2
09425
4.1/2
7/8
15/16
1
2
UTILITY
TPI
(Thread
per Inch)
09400
13/16
Used for follow through right to the bottom
to obtain full depth of thread. As opposed to
straight threads such as BSW, UNC, UNF, Metric
etc; taps with parallel threads are shorter in
length and are used for parallel threading.
These are used in sets of 2. All taps are right
hand taps.
Ordering
Nr.
TAP/1-16
3/4
Bottom
Cat. Nr.
1/16
11/16
Used to increase the size of cut.
British Standard FINE (BSF) 55° - Set of 3
Ordering
Nr.
metalworking
Taper>
CB 82
Second >
Bottom >
section 6
Unified Coarse (UNC) 60° - Set of 3
Nominal
Size
Cat. Nr.
Unified FINE (UNF) 60° - Set of 3
Ordering
Nr.
TPI
(Thread
per Inch)
Nominal
Size
Inch
Cat. Nr.
Metric -Set of 3
Ordering
Nr.
TPI
(Thread
per Inch)
Inch
Nominal
Size
Cat. Nr.
Ordering
Nr.
Pitch
Inch
1/4
TAP/UNC/1-4
09900
20
1 /4
TAP/UNF/1-4
10100
28
2
TAP/2M
09602
0.40
9/32
TAP/UNC/9-32
09909
20
5/16
TAP/UNF/5-16
10101
24
3
TAP/3M
09603
0.50
5/16
TAP/UNC/5-16
09901
18
3/8
TAP/UNF/3-8
10102
24
4
TAP/4M
09604
0.70
3/8
TAP/UNC/3-8
09902
16
7/16
TAP/UNF/7-16
10107
20
5
TAP/5M
09605
0.80
7/16
TAP/UNC/7-16
09903
14
1 /2
TAP/UNF/1-2
10103
20
6
TAP/6M
09606
1.00
1 /2
TAP/UNC/1-2
09904
13
9/32
TAP/UNF/9-32
10117
7
TAP/7M
09607
1.00
9/16
TAP/UNC/9-16
09910
12
9/16
TAP/UNF/9-16
10108
18
8
TAP/8/1/M
09660
1.00
5/8
TAP/UNC/5-8
09905
11
5/8
TAP/UNF/5-8
10104
18
8
TAP/8M
09608
1.25
TAP/UNC/11-16
09911
11
11/16
TAP/UNF/11-16
10109
18
TAP/9/1/M
09661
1.00
TAP/UNC/3-4
09906
10
3/ 4
TAP/UNF/3-4
10105
16
9
TAP/9M
09609
1.25
TAP/UNC/13-16
09912
10
13/16
TAP/UNF/13-16
10110
16
10
TAP/10M/SPL1
09663
1.00
TAP/UNC/7-8
09907
9
7/8
TAP/UNF/7-8
10111
14
10
TAP/10M/SPL
09662
1.25
TAP/UNC/15-16
09913
9
15/16
TAP/UNF/15-16
10112
14
10
TAP/10M
09610
1.50
TAP/UNC/0-1
09908
8
1
TAP/UNF/0-1
10106
12
11
TAP/11M
09611
1.50
1.1/8
TAP/UNC/1-1-8
09914
7
1.1/8
TAP/UNF/1-1-8
10113
12
TAP/12M/SPL2
09666
1.00
1.1/4
TAP/UNC/1-1-4
09915
7
1.1/4
TAP/UNF/1-1-4
10114
12
12
TAP/12M/SPL
09664
1.25
1.3/8
TAP/UNC/1-3-8
09916
6
1.3/8
TAP/UNF/1-3-8
10115
12
12
TAP/12M/SPL1
09665
1.50
1.1/2
TAP/UNC/1-1-2
09917
6
1.1/2
TAP/UNF/1-1-2
10116
12
12
TAP/12M
09612
1.75
1.3/4
TAP/UNC/1-3-4
09918
5
14
TAP/14M/SPL
09667
1.25
TAP/UNC/0-2
09919
4.1/2
TAP/14M/SPL1
09668
1.50
TAP/14M
09614
2.00
TAP/16M/SPL
09669
16
TAP/16M
09616
2.00
18
TAP/18M/SPL
09670
1.50
TAP/18M/SPL1
09671
2.00
TAP/18M
09618
2.5
TAP/20M/SPL
09672
1.5
TAP/20M/SPL1
09673
2.00
11/16
3 /4
13/16
7/8
15/16
1
2
British Standard Parallel (BSP) 55° - Set of 2
Nominal
Size
Cat. Nr.
Ordering
Nr.
Inch
TPI
(Thread
per Inch)
1/8
TAP/2/BSP/1-8
09500
28
1 /4
TAP/2/BSP/1-4
09501
19
3/8
TAP/2/BSP/3-8
09502
19
1 /2
TAP/2/BSP/1-2
09503
14
5/8
TAP/2/BSP/5-8
09504
14
3 /4
TAP/2/BSP/3-4
09505
14
7/8
TAP/2/BSP/7-8
09507
14
1
TAP/2/BSP/0-1
09506
11
1.1/4
TAP/2/BSP/1-1-4
09508
11
1.1/2
TAP/2/BSP/1-1-2
09509
11
1.3/4
TAP/2/BSP/1-3-4
09511
11
TAP/2/BSP/0-2
09510
11
2
14
18
20
TAP/20M
09620
2.5
TAP/22M/SPL1
09674
1.50
22
TAP/22M
09622
2.5
24
TAP/24M
09624
3.0
27
TAP/27M
09627
3.0
30
TAP/30M
09630
3.5
33
TAP/33M
09633
3.5
36
TAP/36M
09636
4.0
39
TAP/39M
09639
4.0
42
TAP/42M
09642
4.5
45
TAP/45M
09645
4.5
48
TAP/48M
09648
5.0
52
TAP/52M
09652
5.0
Pitch
Length of Square
Shank
Diameter
Pitch
Diameter
Thread Length
Length of Shank
Overall Shank
CB 83
section 6
72 Dies – Carbon Steel
espTerrajas
frFilieres
deSchneideisen
Unified Round Dies
Nominal
Size
Dies are used for cutting external threads.These are used as individual
pieces, the same die being passed over the job many times to obtain clean
threading. Manufactured from carbon steel.
These are available in two types: Round and Hexagonal
British Standard Round Dies
Nominal
Size
Outer
Diameter
Inch
Inch
Cat. Nr.
Ordering
Nr.
British Standard
Whitworth 55° (BSW)
Cat.Nr.
Ordering
Nr.
British Standard
Fine 55° (BSW)
Outer
Diameter
Cat. Nr.
Ordering
Nr.
Cat. Nr.
Ordering
Nr.
Inch
Inch
1/16
13/16
DI/UNF/0-47
15000
DI/UNC/0-70
15100
3/32
13/16
DI/UNF/0-48
15001
DI/UNC/0-71
15101
1/ 8
13/16
DI/UNF/0-49
15002
DI/UNC/0-72
15102
5/32
13/16
DI/UNF/0-50
15003
DI/UNC/0-73
15103
3/16
13/16
DI/UNF/0-51
15004
DI/UNC/0-74
15104
7/32
13/16
DI/UNF/0-52
15005
DI/UNC/0-75
15105
1 /4
1
DI/UNF/0-53
15006
DI/UNC/0-76
15106
1 /4
13/16
DI/UNF/0-53/SPL
15007
DI/UNC/0-76/SPL
15107
5/16
1
DI/UNF/0-54
15008
DI/UNC/0-77
15108
3/8
1
DI/UNF/0-55
15009
DI/UNC/0-78
15109
5/16
1.1/2
DI/UNF/0-56
15010
DI/UNC/0-79
15110
3/8
1.1/2
DI/UNF/0-57
15011
DI/UNC/0-80
15111
Unified Fine 60° (UNF)
Unified Coarse 60° (UNC)
1/16
13/16
DI/0-1
10201
DI/BSF/0-24
14900
7/16
1.1/2
DI/UNF/0-58
15012
DI/UNC/0-81
15112
3/32
13/16
DI/0-2
10202
DI/BSF/0-25
14901
1 /2
1.1/2
DI/UNF/0-59
15013
DI/UNC/0-82
15113
1/ 8
13/16
DI/0-3
10203
DI/BSF/0-26
14902
9/16
1.1/2
DI/UNF/0-60
15014
DI/UNC/0-83
15114
5/32
13/16
DI/0-4
10204
DI/BSF/0-27
14903
5/8
1.1/2
DI/UNF/0-61
15015
DI/UNC/0-84
15115
3/16
13/16
DI/0-5
10205
DI/BSF/0-28
14904
11/16
1.1/2
DI/UNF/0-62
15016
DI/UNC/0-85
15116
7/32
13/16
DI/0-6
10206
DI/BSF/0-29
14905
3 /4
1.1/2
DI/UNF/0-63
15017
DI/UNC/0-86
15117
1 /4
1
1 /4
13/16
DI/0-7
10207
DI/BSF/0-30
14906
7/8
2
DI/UNF/0-64
15018
DI/UNC/0-87
15118
DI/0-7/SPL
10224
DI/BSF/0-30/SPL
14907
1
2
DI/UNF/0-65
15019
DI/UNC/0-88
5/16
15119
1
DI/0-8
10208
DI/BSF/0-31
14908
1.1/8
2.1/4
DI/UNF/0-66
15020
DI/UNC/0-89
15120
3/8
1
DI/0-9
10209
DI/BSF/0-32
14909
1.1/8
2.1/2
DI/UNF/0-66/SPL
15021
DI/UNC/0-89/SPL
15121
5/16
1.1/2
DI/0-10
10210
DI/BSF/0-33
14910
1.1/4
2.1/4
DI/UNF/0-67
15022
DI/UNC/0-90
15122
3/8
1.1/2
DI/0-11
10211
DI/BSF/0-34
14911
1.1/4
2.1/2
DI/UNF/0-67/SPL
15023
DI/UNC/0-90/SPL
15123
7/16
1.1/2
DI/0-12
10212
DI/BSF/0-35
14912
1.3/8
3
DI/UNF/0-68
15024
DI/UNC/0-91
15124
1 /2
1.1/2
DI/0-13
10213
DI/BSF/0-36
14913
1.1/2
3
DI/UNF/0-69
15025
DI/UNC/0-92
15125
9/16
1.1/2
DI/0-14
10214
DI/BSF/0-37
14914
5/8
1.1/2
DI/0-15
10215
DI/BSF/0-38
14915
11/16
1.1/2
DI/0-16
10216
DI/BSF/0-39
14916
3 /4
1.1/2
DI/0-17
10217
DI/BSF/0-40
14917
7/8
2
DI/0-18
10218
DI/BSF/0-41
14918
1
2
DI/0-19
10219
DI/BSF/0-42
14919
1.1/8
2.1/4
DI/0-20
10220
DI/BSF/0-43
14920
1.1/8
2.1/2
DI/0-20/SPL
10225
DI/BSF/0-43/SPL
14921
1.1/4
2.1/4
DI/0-21
10221
DI/BSF/0-44
14922
1.1/4
2.1/2
DI/0-21/SPL
10226
DI/BSF/0-44/SPL
14923
1.3/8
3
DI/0-22
10222
DI/BSF/0-45
14924
1.1/2
3
DI/0-23
10223
DI/BSF/0-46
14925
UTILITY
metalworking
Outside
Diameter
Clearance
Hole
CB 84
Cutting
Edge
section 6
Metric Round Dies
British Standard Parallel 55° (BSP) Round Dies
Nominal Size
Outer Diameter
Cat. Nr.
Ordering Nr.
Inch
Inch
2x0.4
13/16
DI/2M
10402
1/ 8
1
DI/BSP/0-93
15200
3x0.5
13/16
DI/3M
10403
1 /4
1.1/2
DI/BSP/0-94
15201
4x0.7
13/16
DI/4M
10404
3/8
1.1/2
DI/BSP/0-95
15202
4 X 0.75
13/16
DI/4M-SPL
10440
1/ 2
2
DI/BSP/0-96
15203
5x0.8
13/16
DI/5M
10405
5/8
2
DI/BSP/0-97
15204
5 X 0.90
13/16
DI/5M-SPL
10441
3/ 4
2
DI/BSP/0-98
15205
6x1.0
1
DI/6M
10406
1
2.1/4
DI/BSP/0-99
15206
6 x 1.0
1.1/2
DI/6M-SPL
10442
1
2.1/2
DI/BSP/0-100
15207
7x1.0
1
DI/7M
10407
1.1/4
3
DI/BSP/0-101
15208
8x1.0
1
DI/8M-SPL1
10443
8x1.25
1
DI/8M
10408
8x1.25
1.1/2
DI/8M-SPL
10444
9 x 1.0
1
DI/9M-SPL
10445
9x1.25
1
DI/9M
10409
10 X 1.25
1
DI/10M-SPL1
10447
10x1.5
1
DI/10M
10410
10x1.5
1.1/2
DI/10M-SPL
10446
11 X 1.5
1.1/2
DI/11M
104411
12 X 1.5
1.1/2
DI/12M-SPL
10448
12x1.75
1.1/2
DI/12M
10412
13x1.75
1.1/2
DI/13M
10413
14x2.0
1.1/2
DI/14M
10414
10416
16x2.0
1.1/2
DI/16M
18x2.5
1.1/2
DI/18M
10418
20x2.5
2
DI/20M
10420
22x2.5
2
DI/22M
10422
24x3.0
2
DI/24M
10424
27x3.0
2.1/2
DI/27M
10427
30x3.5
2.1/2
DI/30M
10430
CB 85
Nominal Size
Outer Diameter
Inch
Inch
Cat. Nr.
Ordering Nr.
section 6
HexagonalDies–CarbonSteel
(BSF) 55° Hexagonal Dies
Nominal A/F (Across Thickness
Size
Flats)
(UNC) 60° Hexagonal Dies
Cat. Nr.
Ordering
Nr.
Inch
Inch
Inch
1/8
0.710
1 /4
DI/H/BSF/1-8
10600
5/32
0.710
1 /4
DI/H/BSF/5-32
10607
7/32
0.710
1 /4
DI/H/BSF/7-32
10608
1 /4
0.710
1 /4
DI/H/BSF/1-4
10601
9/32
0.820
5/16
DI/H/BSF/9-32
10609
5/16
0.820
5/16
DI/H/BSF/5-16
10610
3/8
0.920
3/8
DI/H/BSF/3-8
10602
7/16
1.010
7/16
DI/H/BSF/7-16
10611
1 /2
1.100
1/ 2
DI/H/BSF/1-2
10603
9/16
1.300
5/8
DI/H/BSF/9-16
10612
5/8
1.300
5/8
DI/H/BSF/5-8
10604
3/4
1.480
11/16
DI/H/BSF/3-4
10605
7/8
1.670
13/16
DI/H/BSF/7-8
10613
1
2.050
15/16
DI/H/BSF/0-1
10606
1.1/8
2.220
1.1/16
DI/H/BSF/1-1-8
10614
1.1/4
2.220
1.1/16
DI/H/BSF/1-1-4
10615
1.3/8
2.580
1.1/8
DI/H/BSF/1-3-8
10616
1.1/2
2.760
1.1/4
DI/H/BSF/1-1-2
10617
1.5/8
2.760
1.1/4
DI/H/BSF/1-5-8
10618
1.3/4
3.150
1.3/8
DI/H/BSF/1-3-4
10619
1.7/8
3.150
1.3/8
DI/H/BSF/1-7-8
16620
2
3.330
1.3/4
DI/H/BSF/0-2
10621
Nominal Size
A/F (Across Flats) Thickness
Inch
Inch
Inch
Cat. Nr.
Ordering
Nr.
1/8
0.710
1 /4
DI/H/UNC/1-8
14808
5/32
0.710
1 /4
DI/H/UNC/5-32
14810
7/32
0.710
1 /4
DI/H/UNC/7-32
14811
1 /4
0.710
1 /4
DI/H/UNC/1-4
14800
9/32
0.820
5/16
DI/H/UNC/9-32
14812
5/16
0.820
5/16
DI/H/UNC/5-16
14801
3/8
0.920
3/8
DI/H/UNC/3-8
14802
7/16
1.010
7/16
DI/H/UNC/7-16
14813
1 /2
1.100
1/ 2
DI/H/UNC/1-2
14803
9/16
1.300
5/8
DI/H/UNC/9-16
14814
5/8
1.300
5/8
DI/H/UNC/5-8
14804
3/4
1.480
11/16
DI/H/UNC/3-4
14805
7/8
1.670
13/16
DI/H/UNC/7-8
14809
1
2.050
15/16
DI/H/UNC/0-1
14806
1.1/8
2.220
1.1/16
DI/H/UNC/1-1-8
14807
1.1/4
2.220
1.1/16
DI/H/UNC/1-1-4
14815
1.3/8
2.580
1.1/8
DI/H/UNC/1-3-8
14816
1.1/2
2.760
1.1/4
DI/H/UNC/1-1-2
14817
1.5/8
2.760
1.1/4
DI/H/UNC/1-5-8
14818
1.3/4
3.150
1.3/8
---
---
1.7/8
3.150
1.3/8
---
---
2
3.330
1.3/4
---
---
(BSW) 55° Hexagonal Dies
Nominal Size
A/F (Across Flats)
Thickness
Inch
Inch
Inch
Cat. Nr.
Ordering
Nr.
1/8
0.710
1 /4
DI/H/1-8
10800
5/32
0.710
1 /4
DI/H/5-32
10809
7/32
0.710
1 /4
DI/H/7-32
10810
3/16
0.710
1/4
DI/H/3-16
10823
1 /4
0.710
1 /4
DI/H/1-4
10802
9/32
0.820
5/16
DI/H/9-32
10811
5/16
0.820
5/16
DI/H/5-16
10812
3/8
0.920
3/8
DI/H/3-8
10803
7/16
1.010
7/16
DI/H/7-16
10813
1 /2
1.100
1/ 2
DI/H/1-2
10804
9/16
1.300
5/8
DI/H/9-16
10814
5/8
1.300
5/8
DI/H/5-8
10805
3/4
1.480
11/16
DI/H/3-4
10806
7/8
1.670
13/16
DI/H/7-8
10807
1
2.050
15/16
DI/H/0-1
10808
1.1/8
2.220
1.1/16
DI/H/1-1-8
10815
1.1/4
2.220
1.1/16
DI/H/1-1-4
10816
1.3/8
2.580
1.1/8
DI/H/1-3-8
10817
1.1/2
2.760
1.1/4
DI/H/1-1-2
10818
1.5/8
2.760
1.1/4
DI/H/1-5-8
10819
1.3/4
3.150
1.3/8
DI/H/1-3-4
10820
1.7/8
3.150
1.3/8
DI/H/1-7-8
10821
2
3.330
1.3/4
DI/H/0-2
10822
Across
Flat
Clearance
Hole
CB 86
Cutting
Edge
section 6
Metric Hexagonal Dies
(UNF) 60° Hexagonal Dies
Nominal Size
Inch
Inch
Inch
Cat. Nr.
Ordering
Nr.
Nominal Size
mm
Inch
Cat. Nr.
Inch
Ordering
Nr.
1/8
0.710
1 /4
DI/H/UNF/1-8
10911
3
0.710
DI/H/3M
10503
5/32
0.710
1 /4
DI/H/UNF/5-32
10912
4
0.710
1 /4
DI/H/4M
10504
7/32
0.710
1 /4
DI/H/UNF/7-32
10913
5
0.710
1 /4
DI/H/5M
10505
1 /4
0.710
1 /4
DI/H/UNF/1-4
10900
6
0.710
1 /4
DI/H/6M
10506
9/32
0.820
5/16
DI/H/UNF/9-32
10914
7
0.820
5/16
DI/H/7M
10507
5/16
0.820
5/16
DI/H/UNF/5-16
10901
8
0.820
5/16
DI/H/8M
10508
3/8
0.920
3/8
DI/H/UNF/3-8
10902
9
0.920
3/8
DI/H/9M
10509
7/16
1.010
7/16
DI/H/UNF/7-16
10915
10
0.920
3/8
DI/H/10M
10510
1 /2
1.100
1/ 2
DI/H/UNF/1-2
10903
11
1.010
7/16
DI/H/11M
10511
9/16
1.300
5/8
DI/H/UNF/9-16
10916
12
1.100
1/2
DI/H/12M
10512
5/8
1.300
5/8
DI/H/UNF/5-8
10904
14
1.300
5/8
DI/H/14M
10514
3/4
1.480
11/16
DI/H/UNF/3-4
10905
16
1.300
5/8
DI/H/16M
10516
7/8
1.670
13/16
DI/H/UNF/7-8
10910
18
1.300
5/8
DI/H/18M
10518
1
2.050
15/16
DI/H/UNF/0-1
10906
18
1.480
11/16
DI/H/18M-SPL
10519
1.1/8
2.220
1.1/16
DI/H/UNF/1-1-8
10908
20
1.480
11/16
DI/H/20M
10520
1.1/4
2.220
1.1/16
DI/H/UNF/1-1-4
10909
22
1.670
13/16
DI/H/22M
10522
1.3/8
2.580
1.1/8
DI/H/UNF/1-3-8
10917
24
2.050
15/16
DI/H/24M
10524
1.1/2
2.760
1.1/4
DI/H/UNF/1-1-2
10918
27
2.220
1.1/16
DI/H/27M
10527
1.5/8
2.760
1.1/4
DI/H/UNF/1-5-8
10919
30
2.220
1.1/16
DI/H/30M
10530
1.3/4
3.150
1.3/8
---
---
33
2.580
1.1/8
DI/H/33M
10533
1.7/8
3.150
1.3/8
---
---
2
3.330
1.3/4
---
---
55° BSP Hexagonal Dies
Nominal Size
Inch
Inch
Inch
Cat. Nr.
Ordering
Nr.
1/8
0.920
3 /8
DI/H/BSP/1-8
10700
1 /4
1.100
1 /2
DI/H/BSP/1-4
10701
3/8
1.300
5/8
DI/H/BSP/3-8
10702
1 /2
1.670
13/16
DI/H/BSP/1-2
10703
5/8
1.670
13/16
DI/H/BSP/5-8
10704
3/ 4
2.050
15/16
DI/H/BSP/3-4
10705
7/8
2.220
1.1/16
DI/H/BSP/7-8
10707
1
2.580
1.1/8
DI/H/BSP/0-1
10706
1.1/4
2.760
1.1/4
DI/H/BSP/1-1-4
10708
1.1/2
3.150
1.1/4
DI/H/BSP/1-1-2
10709
1.3/4
3.330
1.1/4
DI/H/BSP/1-3-4
10710
HEXAGONAL DIES - Also referred to as Die Nuts, these are
used in the same way as Round Dies but are more resilient
and can be easily tightened using a spanner
CB 87
section 6
www.groz-tools.com
Roll Head Pry Bars 89 CAT/Aligning Bars 89
Wheel Wrenches - Double Ended 90
Ring Slogging Wrenches 90
Box Spanners (Box Wrenches) 91
Brass Hammers 92
7
73 Roll Head Pry Bars <No. 331R>
74 Cat / aligning Bars <No. 331C>
esp Barras de Palanca
frPince a Levier
de Hebeleisen mit Rollkopf
esp Barras de Alinear
frPince a Aligner
de Hebeleisen mit Klaue
Manufactured from Chrome Vanadium Steel these are fully hardened
and tempered. Specifically designed for heavy prying & fulcrum prying
especially in automotive applications with the tapered end used for
aligning applications.
These are heavy duty Bars forged from chrome alloy steel. The prying end
is on one side with lining up on the other. The body is fully hardened to
resist any bending. These are available with a round section or hexagonal
section. Both come in an attractive chrome finish which also makes it easier
to locate in crowded work environments.
Cat.Nr.
Ordering
Nr.
Length
Stock Size
Inch
mm
Inch
mm
Cat.Nr.
Ordering
Nr.
PRY/6
33150
6
150
5/16
8
PRY/12
33151
12
300
7/16
11
Round Section Bars
Length
Stock Size/ HEX (A/F)
Inch
mm
Inch
mm
PRY/16
33152
16
400
9/16
14
CAT/18
33170
18
450
5/8
16
PRY/20
33153
20
500
11/16
17
CAT/24
33171
24
600
3/4
19
PRY/4-ST
33154
CAT/30
33172
30
750
7/8
22
CAT/36
33173
36
900
7/8
22
16
400
5/8
16
Set of above 4 Pry Bars
Hexagonal Section Bar
CAT/H/16/CP
38-43
HRC
forged
construction
33175
UTILITY
UTILITY
automotive
35-40
HRC
forged
construction
automotive
CB 89
section 7
75 WheelWrenches–DoubleEnded
76 Ring Slogging Wrenches
esp Llaves rueda
fr Cles doubles pour camion
deSteckschlüsel
esp Anilla de remaches para golpear
fr Cles pour frappe de bague
deSchlagringschlüssel
Heavy duty double ended wheel wrenches; these are made from high grade
alloy steel and have rust preventing bright nickel plated finish. In normal
course each wheel wrench is supplied complete with tommy bar, however,
spare wrenches and tommy bars are also available.
Drop forged from chrome vanadium steel, these are hardened and tempered
and have an attractive black powder coated finish. The design incorporates
a heavy duty hexagon pattern at one end with the other end being the
striking end.
Cat. Nr.
Ordering Nr.
Size
mm
Wheel Wrench with Tommy Bar
WW/D/24-27
31900
24 x 27
uWW/D/27-30
31901
27 x 30
WW/D/27-32
31902
27 x 32
WW/D/27-33
31903
27 x 33
uWW/D/30-32
31904
30 x 32
uWW/D/30-33
31905
30 x 33
WW/D/32-38
31906
32 x 38
WW/D/35-17
31907
35 x 17
WW/D/38-21
31908
38 x 21
uWW/D/41-21
31909
41 x 21
Spare Tommy Bar
TMB/430-19
u
31940
These are used for tightening and slackening large nuts & bolts in ship
maintenance, mining, piping and industrial applications. One end is shaped
to a fit a nut and the other is enlarged to receive blows from a hammer. The
shock of the impact is useful in breaking rust / paint.
Cat. Nr.
Ordering
Nr.
Size
RSW/24
31800
24
uRSW/27
31801
27
uRSW/30
31802
30
RSW/32
31803
32
34
RSW/34
31804
uRSW/36
31805
36
RSW/38
31806
38
uRSW/41
31807
41
430mm x 19mm
BESTSELLER
forged
construction
RSW/46
31808
46
RSW/50
31809
50
RSW/55
31810
55
RSW/60
31811
60
RSW/65
31812
65
RSW/70
31813
70
lRSW/75
31815
75
lRSW/80
31816
80
lRSW/85
31817
85
lRSW/90
31818
90
lRSW/95
31819
95
lRSW/100
31820
100
lRSW/105
31821
105
u
CB 90
mm
39-46
HRC
forged
construction
BESTSELLER l NEW
section 7
77 Box Spanners (Box Wrenches)
esp Llaves vaso
fr Cles en tube
deRohrsteckschlüssel
Cat. Nr.
Manufactured from high quality steel tubing, these double ended box
wrenches have a different socket size on each end. Thin and long body
allows these to be used to loosen or tighten nuts and bolts in narrow,
recessed areas. Box wrenches are used with tommy bars which is passed
through the holes provided in the sides of the wrench. Supplied complete
with tommy bars.
1. Metric Sizes
Size is measured as the width of
the nut across hexagon flats
Ordering
Nr.
Nominal Size
BW/6-7
32000
6 mm x 7 mm
BW/8-9
32001
8 mm x 9 mm
BW/10-11
32002
BW/12-13
Length
mm
Tommy Bar
Length
(mm)
Dia
(mm)
102
77
3
102
102
6
10 mm x 11 mm
102
102
6
32003
12 mm x 13 mm
102
102
6
BW/14-15
32004
14 mm x 15 mm
127
152
9
BW/16-17
32005
16 mm x 17 mm
127
152
9
BW/18-19
32006
18 mm x 19 mm
127
152
9
BW/20-21
32007
20 mm x 21 mm
127
152
9
BW/22-23
32008
22 mm x 23 mm
127
152
9
BW/24-25
32009
24 mm x 25 mm
152
203
12
BW/26-27
32010
26 mm x 27 mm
152
203
12
BW/30-32
32010
30 mm x 32 mm
152
256
16
Sets
BW/6M-ST
2. BA Sizes
Measured in accordance with
British Association specifications
32019
A set of 6 Box wrenches in sizes 8x9, 10x11, 12x13, 14x15,
16x17 & 18x19 with two Tommy bars, packed in a vinyl pouch.
BA Sizes
BW/BA/0-1
32200
0.413” x 0.365”
76.5
77
5
BW/BA/2-3
32201
0.324” x 0.282”
76.5
77
5
BW/BA/4-5
32202
0.248”x 0.220”
76.5
77
5
BW/BA/6-7
32203
0.193” x 0.172”
76.5
77
3
BW/BA/8-9
32204
0.152” x 0. 131”
76.5
77
3
32205
0.11776.5”
76.5
77
3
nBW/BA/10
Sets
BW/6-ST
n
CB 91
32209
A set of 6 Box wrenches in sizes : 0.413”x 0.365”, 0.324”
x 0.282”, 0.248”x 0.220”, 0.193” x 0.172”, 0.152” x 0. 131”,
0.11776.5” with two Tommy bars, packed in a vinyl pouch.
SINGLE ENDED
section 7
78 Brass Hammers
esp Martillo de laton
fr Marteau de laiton
deMessinghämmer
An ideal combination of Brass & Aluminum makes these hammers very safe
for use even in explosive environments. The Brass Head does not spark and
protects metal surfaces from any damage such as denting or marking during
use. The Non slip aluminium handle is knurled for comfortable non-slip grip.
CB 92
Cat.Nr.
Ordering Nr.
Head Wt.
u
BRH/6oz
32490
6oz
u
BRH/1
32491
1 lb
BRH/2-1-2
32492
2.1/2 lbs
BRH/3
32493
3 lbs
BRH/4
32494
4 lbs
u
BESTSELLER
section 7
www.groz-tools.com
8
Paint Mixers 94
Revolving Punch Pliers 94
Metal Bender 95
Hobbyist's Anvils 95
Grommet Kits 96
CB 93
section 8
79 Paint Mixers
80 Revolving Punch Pliers
esp Mezclador de pintura
fr Melangeur de peintures
deRührquirl
espSacabocados tipo estrella
fr Pince emporte - piece
deRevolver-Lochzange
Paint mixers are ideal for mixing paint and a multitude of other low
density materials. Manufactured from a 5/16”(8mm) hexagonal shaft with
fluted construction, these have an attractive red powder coated finish for
increased protection against rust.
Using Paint Mixers
Place Paint Mixer in the container of material and gently work around the
container edges till the material starts flowing towards the center of the
blades.
• Continue to gently work on the material till it is of desired consistency.
• For coarse or stiff materials, reverse the direction of the drill and follow
above steps. The mixer works best with a variable speed reversible drill
machine with 400 – 600 watts minimum power.Recommended speed
between 200 – 700 rpm depending upon the material being mixed.
Professional quality pliers, these are made from heavy gauge pressed steel
sheet.
Punches are accurately heat treated for extended life and are exposed to
a brass anvil which prevents the edges from getting damaged in use. Each
punch locates exactly in position locking in place with the prawl and ratchet
mechanism.
Spring loaded revolving head incorporates 6 punches of sizes 5/64" (2 mm),
3/32"(2.5 mm), 1/8"(3.0 mm), 9/64" (3.5 mm), 5/32"(4 mm) & 3/16" (4.5 mm).
Cat. Nr.
uRPL/6
Ordering
Nr.
31600
Length
Inch
mm
8.3/4
220
Important
• Do not use Paint Mixer with lacquer or other such inflammable liquids (with
flashpoint under 32°C – 70°F)
• Insert mixer well into the material before turning on the drill.
• When mixing is complete, wait for the mixer to come to a halt before
removing it from the container.
Cat. Nr.
Ordering
Nr.
Dia. of
Mixing Wheel
Length
Fits Drill Size
Inch
mm
Inch
mm
Inch
mm
uPMX/60
14620
2.3/8
60
16
400
3/8
9.5
PMX/80
14621
3.3/16
80
16
400
3/8
9.5
u
BESTSELLER
<PMX/80
PMX/60>
CB 94
section 8
81 Metal Bender
82 Hobbyist’s Anvils
espCurva-metales
frCourbe-metaux
deBieger-Metall
esp Yunques bricolage
frEnclumes - amateur
deLiebhaber-Ambosse
A unique light weight tool, used for bending metal, pipes & solid bars. Ideal
for use in industry, model making and in DIY applications at home, garages,
workshops etc.
Forged from selected steel, anvils are chrome plated for increased resistance
to corrosion. These are especially useful in jewellery making and other DIY
applications.
The unit comes complete with an assortment of mandrels & grooved
bending rollers which can be used for shaping hinges, brackets, wrought
iron, chain links, hooks, clamps, tubings and much more. The complete unit
comes packed in a convenient and easy to store metal case. The bender can
be mounted using a vice or holes drilled in the body and set up on a work
bench.
Cat. Nr.
Ordering
Nr.
Height
Inch
Base Dimensions
mm
Inch
mm
Type
AVL/CP-01
14200
1.3/4
45
2.1/4 x 1 /4
56 X 32
Without Base
AVL/CP-02
14201
3.5/16
83
Ǿ 2.7/8
Ǿ 72
With Base
Suitable for shaping
• Metal sheets upto 1.9/16” (40 mm) wide and 5/32” (4 mm) thick.
• Pipes with external diameter upto 3/8” (10 mm).
• Solid bars upto 1/4” (6 mm).
forged
construction
Cat. Nr.
MTB/01
Jeweller's
tool
Ordering Nr.
14440
< AVL/CP-02
< AVL/CP-01
Metal Bender >
CB 95
section 8
83 Grommet KITS
espOjales
frCanonsisolants
de Gummimuffen
Grommets or eyelets as they are commonly called are used to repair canvas,
tarpaulins, tents, awnings, sailcloth, lawn furniture, pool covers etc.
These are offered as a kit containing:
• Solid Brass Grommets
• Hole Punch
• Backer block
• Setting Tool
• Anvil
Grommets are made from solid brass making them rust resistant. Hole
Punch and Setting Tool are precision machined from single bar of solid steel
for additional durability.
Replacement Grommets also available
Cat.Nr.
Ordering
Nr.
Size
Kit Constituents
GRMT/1-4/ST
26600
1/4"(6mm)
Includes 24 brass grommets
(eyelets), hole punch, backer block,
setting tool and anvil
GRMT/3-8/ST
26601
3/8"(10mm)
Includes 12 brass grommets
(eyelets), hole punch, backer block,
setting tool and anvil
GRMT/1-2/ST
26602
1/2"(12mm)
1/2"(13mm)Includes 12 brass grommets (eyelets), hole punch, backer
block, setting tool and anvil
Grommet Kits
Replacement Grommets
GRM/B/1-4/ST24
26650
1/4"(6mm)
24 Replacement Grommets
GRM/B/3-8/ST12
26651
3/8"(10mm)
GRM/B/1-2/ST12
26652
1/2"(12mm)
Hole Punch >
< Setting Tool
GROMMET KIT
< Washer
Grommets
< Grommet
< Anvil
< Backer Block
CB 96
section 8
CB02 INDEX
alphabeticalindex
Page
A
Adjustable Bevel
CB 74
Adjustable Tap & Reamer Wrenches - Bar Type
CB 78
Aligning Bars / Cat Bars
CB 89
Anvils
Cast Steel
CB 40
Hobbyist's
CB 95
Arch & Hollow Punches
CB 19
Automatic Centre Punches
CB 17
B
Page
Fret
Concrete Point
CB 24
Handyman's
Electrician's
CB 27
Junior
Plugging
CB 24
Junior - Baby Bite
Scutch Holding
CB 24
Junior Saw
Clamps
Piercing Duo Bar Clamp
CB 69
Professional
G - Drop Forged - Heavy Duty
CB 43
Universal
G -Drop Forged
CB 42
Hand Taps - Carbon Steel
G -General Purpose
CB 41
Hand Vices
G- Hobbyist's
CB 44
Hinge Centering Punch
G -Junior
CB 44
Hobbyist's Anvils
KWIK - Quick Action
CB 67
Hobbyist's Vices
Rapid Action I Bar
CB 68
Hollow & Arch Punches
Sash Bar
CB 70
T Bar
CB 70
Compass, Wing
CB 74
Concrete Point Chisels
CB 24
Coping Saw Blades
CB 55
I Bar Clamps - Rapid Action
Coping Saw Frames
CB 52
Cramp Head Set
CB 69
Bar Clamps
Duo Bar
CB 69
Rapid Action I Bar
CB 68
Sash Bar
CB 70
T Bar
CB 70
Bar Type Tap & Reamer Wrenches
CB 78
Bars
Aligning / Cat
CB 89
Pry Bars
CB 89
Die Stock Holders
CB 80
Wrecking Bars
CB 25
Dies - Carbon Steel
Bench Planes
CB 58, CB 59
Round
CB 84, CB 85
Bench Vices
Hexagonal
CB 86, CB 87
Engineer's Steel Vices
CB 35
Dividers
CB 72
Mechanic's Vices
CB 34
Drift Punches
CB 14
Offset Jaw Vices
CB 35
Drill Press Vices
Blades
DIY
CB 37
Coping Saw
CB 55
Unigrip
CB 36
Fret Saw
CB 55
Duo Bar Clamps
CB 69
Hacksaw
CB 54
Duplex Rabbet & Fillister Plane
CB 60
Mini Saw
CB 56
Piercing Saw
CB 54
Block Planes
CB 61
Bolsters
Brick
CB 26
Electrician's Bolsters
CB 27
Chasing
CB 27
Engineer's Bench Vice - All Steel
CB 35
Electricians
CB 27
Eyelets/ Grommets
CB 96
Bolsters & Chisel Merchandiser Packs
CB 32
Box Spanners
CB 91
Brass Calipers
CB 76
Brass Hammers
CB 92
Bricklayer's Line Pins
CB 25
Fret Saw Blades
CB 55
Fret Saw Frames
CB 53
Front End Woodworking Vice
CB 66
D
E
F
C
Page
CB 53
CB 46
CB 49
CB 49
CB 50
CB 51
CB 47
CB 48
CB 82, CB 83
CB 40
CB 15
CB 95
CB 39
CB 19
I
CB 68
J
Junior Saw Frames
CB 49
K
Kits - Punch & Chisel
CB 28, CB 29, CB 30, CB 31
Kwik Action Woodworking Clamps
CB 67
L
Letter & Number Stamps
Line Pins - Bricklayer's CB 20
CB 25
M
Marking Punch
Merchandiser Packs - Chisels & Bolsters
Metal Bender
Mini Saw Blades
CB 17
CB 32
CB 95
CB 56
N
Nail Punches
CB 16
Number & Letter Stamps
CB 20
Calipers
Brass
CB 76
Craftmen's Calipers & Dividers
CB 73
G Clamps
Spring Calipers & Dividers
CB 72
Drop Forged
CB 42
Offset Jaw Vices
CB 35
Cat Bars / Aligning Bars
CB 89
Drop Forged - Heavy Duty
CB 43
Centre Punches
General Purpose
CB 41
Automatic CB 17
Hobbyist's
CB 44
Heavy Duty
CB 8
Junior
CB 44
Paint Mixers
CB 94
Round Shank - Round Head
CB 9
Grommet Kits
CB 96
Piercing Saw Blades
CB 54
Round Shank - Square Head
CB 9
Piercing Saw Frames
CB 47
Centre Square
CB 75
Planes
Chasing Chisels
CB 27
Bench
CB 58, CB 59
Chisel & Bolster Merchandiser Packs
CB 32
Hacksaw Blades
CB 54
Block
CB 61
Chisels
Hacksaw Frame
Duplex Rabbet & Fillister
CB 60
Chasing
CB 27
Coping
CB 52
Plier - Revolving Punch
CB 94
Cold
CB 22, CB 23
G
O
P
H
CB 97
section 1
CB02 INDEX
alphabeticalindex
Page
Page
Plugging Chisel
CB 24
Precision Squares
CB 75
Pry Bars - Roll Head
CB 89
Punch & Chisel Kits
CB 28, CB 29, CB 30, CB 31
Punches
Automatic
CB 17
Centre Punch - Heavy Duty
CB 8
Centre Punch - Round Shank
Round Head
CB 9
Centre Punch - Round Shank
Square Head
CB 9
Drift CB 14
Hinge Centering
CB 15
Hollow & Arch
CB 18, CB 19
Letter & Number
CB 20
Marking
CB 17
Nail
CB 16
Pin Punches - Heavy Duty
CB 10, CB 11
Pin Punches - General Purpose
CB 12, CB 13
Prick Punches CB 16
Roll Pin CB 15
Starting CB 14
S
Page
V
Sash Bar Clamps
CB 70
Vices
Saw Frames
Bench
CB 34
Coping Saw
CB 52
Drill Press - DIY
CB 37
Fret Saw
CB 53
Drill Press - Unigrip
CB 36
Handyman's
CB 46
Engineer's Steel Vice
CB 35
Junior
CB 49, CB 50
Hand
CB 40
Piercing Saw
CB 47
Hobbyist's
CB 39
Professional
CB 47
Offset Jaw Vice
CB 35
Universal
CB 48
Reversible
CB 38
Scutch Holding Chisel
CB 24
Woodworking - Front
CB 66
Slogging Wrenches
CB 90
Woodworking - Plain Screw
CB 62
Spanners - Box
CB 91
Woodworking - Portable
CB 63
Spring Calipers & Dividers
CB 72
Woodworking - Quick Release
CB 64
Squares
Woodworking - Rapid Action
CB 65
Centre
CB 75
Precision
CB 75
Starting Punches
CB 14
Steel Rules
CB 76
Steel Stamps - Number & Letters
CB 20
Wing Compass
CB 74
Swivels Bases - Bench Vices
CB 34
Woodworking Clamps - Rapid Action
CB 68
Woodworking Vices
Front
CB 66
Plain Screw
CB 62
Quick Action Woodworking Clamps
CB 67
Portable
CB 63
T - Bar Clamps
CB 70
Quick Release
CB 64
Tap & Die Sets
CB 81
Rapid Action
CB 65
Tap & Reamer Wrenches - Bar Type
CB 78
Wrecking Bar
CB 25
Tap Wrenches - T Handle Type
CB 79
Wrenches
Rapid Action Woodworking Clamps
CB 68
Taps - Carbon Steel
CB 82, CB 83
Box
CB 91
Reversible Vice
CB 38
Ring Slogging
CB 90
Revolving Punch Pliers
CB 94
Tap - Bar Type
CB 78
Ring Slogging Wrenches
CB 90
Tap - T Type
CB 79
Roll Pin Punches
CB 15
Wheel - Double Ended
CB 90
Rules - Steel
CB 76
Universal Saw Frame
CB 48
Q
W
T
R
U
numerical index
Ordering Nr.
Page
Ordering Nr.
25200
25201
25202
25206
25203
25207
25204
25205
25100
25101
25102
25103
25104
25105
25106
25108
25109
25110
25120
25150
25151
25152
25153
CB 8
CB 8
CB 8
CB 8
CB 8
CB 8
CB 8
CB 8
CB 9
CB 9
CB 9
CB 9
CB 9
CB 9
CB 9
CB 9
CB 9
CB 9
CB 9
CB 9
CB 9
CB 9
CB 9
25154
25155
25156
25600
25601
25609
25602
25603
25604
25610
25605
25606
25607
25608
25612
25611
25650
25651
25652
25653
25654
25655
25560
CB 98
Page
CB 9
CB 9
CB 9
CB 10
CB 10
CB 10
CB 10
CB 10
CB 10
CB 10
CB 10
CB 10
CB 10
CB 10
CB 10
CB 10
CB 11
CB 11
CB 11
CB 11
CB 11
CB 11
CB 12
Ordering Nr.
25561
25562
25563
25564
25565
25567
25568
25569
25580
25540
25541
25542
25543
25544
25545
25546
25547
25548
25549
25550
25500
25501
25502
Page
CB 12
CB 12
CB 12
CB 12
CB 12
CB 12
CB 12
CB 12
CB 12
CB 13
CB 13
CB 13
CB 13
CB 13
CB 13
CB 13
CB 13
CB 13
CB 13
CB 13
CB 13
CB 13
CB 13
Ordering Nr.
25503
25504
25505
25506
25507
25508
25509
25700
25701
25702
25703
25706
25707
25708
25709
25800
25801
25802
25822
25803
25820
25804
25823
Page
CB 13
CB 13
CB 13
CB 13
CB 13
CB 13
CB 13
CB 14
CB 14
CB 14
CB 14
CB 14
CB 14
CB 14
CB 14
CB 14
CB 14
CB 14
CB 14
CB 14
CB 14
CB 14
CB 14
Ordering Nr.
25805
25806
25807
25824
25808
25809
25640
25641
25642
25643
25644
25645
25646
25004
25450
25451
25452
25360
25361
25362
25363
25364
25365
Page
CB 14
CB 14
CB 14
CB 14
CB 14
CB 14
CB 15
CB 15
CB 15
CB 15
CB 15
CB 15
CB 15
CB 15
CB 16
CB 16
CB 16
CB 16
CB 16
CB 16
CB 16
CB 16
CB 16
Ordering Nr.
25366
25000
25010
25011
25020
26302
26303
26304
26305
26371
26306
26307
26308
26309
26310
26372
26311
26312
26313
26314
26315
26316
26317
Page
CB 16
CB 17
CB 17
CB 17
CB 17
CB 18
CB 18
CB 18
CB 18
CB 18
CB 18
CB 18
CB 18
CB 18
CB 18
CB 18
CB 18
CB 18
CB 18
CB 18
CB 18
CB 18
CB 18
Ordering Nr.
26318
26319
26320
26321
26322
26323
26324
26325
26400
26401
26402
26403
26404
26405
26406
26407
26408
26409
26410
26411
26412
26413
26326
Page
CB 18
CB 18
CB 18
CB 18
CB 18
CB 18
CB 18
CB 18
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB02 INDEX
numerical index
Ordering Nr.
26327
26328
26329
26330
26331
26332
26333
26334
26335
26336
26337
26338
26339
26340
26341
26342
26343
26344
26345
26346
26347
26348
26349
26350
26352
26354
26355
26357
26358
26360
26362
26363
26365
26367
26368
26370
26390
26440
26391
26392
26441
26442
26395
26396
26397
25900
25901
25902
25903
25904
25905
25906
25907
25908
26100
26101
26102
26103
26104
26105
26106
26107
26108
32827
32800
32828
32801
32817
CB 99
Page
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 19
CB 20
CB 20
CB 20
CB 20
CB 20
CB 20
CB 20
CB 20
CB 20
CB 20
CB 20
CB 20
CB 20
CB 20
CB 20
CB 20
CB 20
CB 20
CB 23
CB 23
CB 23
CB 23
CB 23
Ordering Nr.
32829
32802
32803
32818
32831
32810
32804
32819
32811
32820
32805
32811
32812
32815
32832
32806
32821
32813
32807
32833
32718
32814
32824
32816
32834
32830
32712
32812
32815
32807
32718
32814
32816
32650
32651
32652
32653
32654
32656
32657
32655
33100
33101
33102
33103
33104
33105
33106
33107
33818
32659
32601
32602
32603
32621
32622
32628
32642
32641
32643
32645
32658
33001
33003
33004
33000
33002
33005
Page
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 23
CB 24
CB 24
CB 24
CB 24
CB 24
CB 24
CB 24
CB 24
CB 25
CB 25
CB 25
CB 25
CB 25
CB 25
CB 25
CB 25
CB 25
CB 25
CB 26
CB 26
CB 26
CB 26
CB 26
CB 26
CB 27
CB 27
CB 27
CB 27
CB 27
CB 28
CB 29
CB 29
CB 30
CB 30
CB 31
Ordering Nr.
33006
33050
33051
35400
35401
35402
35403
35404
35405
35406
35407
35408
35409
35420
35421
35422
35423
35424
35450
35451
35452
35460
35461
35462
35120
35121
35122
35125
35194
35195
35196
35530
35510
35511
35512
35513
35514
35515
35516
35517
35518
35519
35521
35522
35523
35524
35525
35526
35520
35500
35501
35502
14210
14211
14212
14213
14214
14215
14216
14217
14219
14220
35807
35800
35801
35802
35803
35804
Page
CB 31
CB 32
CB 32
CB 34
CB 34
CB 34
CB 34
CB 34
CB 34
CB 34
CB 34
CB 34
CB 34
CB 34
CB 34
CB 34
CB 34
CB 34
CB 35
CB 35
CB 35
CB 35
CB 35
CB 35
CB 36
CB 36
CB 36
CB 36
CB 37
CB 37
CB 37
CB 38
CB 39
CB 39
CB 39
CB 39
CB 39
CB 39
CB 39
CB 39
CB 39
CB 39
CB 39
CB 39
CB 39
CB 39
CB 39
CB 39
CB 39
CB 40
CB 40
CB 40
CB 40
CB 40
CB 40
CB 40
CB 40
CB 40
CB 40
CB 40
CB 40
CB 40
CB 41
CB 41
CB 41
CB 41
CB 41
CB 41
Ordering Nr.
35805
35850
35851
35700
35701
35702
35703
35704
35740
35741
35742
35743
35744
35713
35714
35715
35710
35711
35712
35730
35731
35732
35733
35735
35734
35820
35821
35822
35823
35824
30010
30000
30001
30140
30111
30100
30101
30130
30131
30120
30200
30201
30220
30221
30223
30222
30324
30325
30326
30327
30343
30344
30345
30346
30342
30347
30348
30349
30380
30357
30358
30359
30360
30361
30362
30363
30314
30303
Page
CB 41
CB 41
CB 41
CB 42
CB 42
CB 42
CB 42
CB 42
CB 42
CB 42
CB 42
CB 42
CB 42
CB 43
CB 43
CB 43
CB 43
CB 43
CB 43
CB 44
CB 44
CB 44
CB 44
CB 44
CB 44
CB 44
CB 44
CB 44
CB 44
CB 44
CB 46
CB 47
CB 47
CB 48
CB 49
CB 49
CB 49
CB 50
CB 50
CB 50
CB 51
CB 51
CB 52
CB 52
CB 53
CB 53
CB 54
CB 54
CB 54
CB 54
CB 54
CB 54
CB 54
CB 54
CB 54
CB 54
CB 54
CB 54
CB 54
CB 55
CB 55
CB 55
CB 55
CB 55
CB 55
CB 55
CB 55
CB 56
Ordering Nr.
30304
30305
39700
39701
39702
39703
39704
39721
39730
39791
39790
39000
39001
39002
39004
39005
39006
39007
39009
39014
39011
39012
39020
39180
39181
39182
39183
39184
39160
39161
39162
39163
39164
39165
39130
39131
39132
39133
39134
39135
39120
39110
39111
39112
39113
39114
39115
39100
39101
39102
39103
39151
01400
01401
01402
01403
01404
01405
01430
01431
01432
01433
01434
01435
01410
01411
01412
01413
Page
CB 56
CB 56
CB 58
CB 58
CB 58
CB 58
CB 58
CB 59
CB 60
CB 61
CB 61
CB 62
CB 62
CB 62
CB 62
CB 62
CB 63
CB 64
CB 64
CB 64
CB 65
CB 65
CB 66
CB 67
CB 67
CB 67
CB 67
CB 67
CB 68
CB 68
CB 68
CB 68
CB 68
CB 68
CB 69
CB 69
CB 69
CB 69
CB 69
CB 69
CB 69
CB 70
CB 70
CB 70
CB 70
CB 70
CB 70
CB 70
CB 70
CB 70
CB 70
CB 70
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
Ordering Nr.
01414
01415
01420
01421
01422
01423
01424
01425
01430
01431
01432
01433
01434
01435
01440
01441
01442
01443
01444
01445
01450
01451
01452
01453
01454
01455
01460
01461
01462
01463
01464
01465
01470
01471
01472
01473
01474
01475
01480
01481
01482
01483
01484
01485
01492
01494
01560
01561
01562
01563
01564
01565
01570
01571
01572
01573
01574
01575
01580
01581
01582
01583
01584
01585
01551
01553
01554
39400
Page
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 72
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 73
CB 74
CB 74
CB 74
CB 74
Ordering Nr.
03521
03522
01000
01001
01002
01003
01004
01005
01006
01007
01012
01011
01300
01301
01302
01304
01330
01331
01332
01333
01334
01335
01340
01341
01342
01343
01344
01345
09200
09201
09202
09203
09210
09211
09212
09213
09221
09220
09222
09223
09224
09225
09300
09301
09302
09303
09304
09320
09321
09100
09101
09102
09103
09104
09110
09111
09112
09113
09114
09116
09117
09118
09119
10001
10014
10015
09400
09401
Page
CB 75
CB 75
CB 75
CB 75
CB 75
CB 75
CB 75
CB 75
CB 75
CB 75
CB 75
CB 75
CB 76
CB 76
CB 76
CB 76
CB 76
CB 76
CB 76
CB 76
CB 76
CB 76
CB 76
CB 76
CB 76
CB 76
CB 76
CB 76
CB 78
CB 78
CB 78
CB 78
CB 78
CB 78
CB 78
CB 78
CB 78
CB 78
CB 78
CB 78
CB 78
CB 78
CB 79
CB 79
CB 79
CB 79
CB 79
CB 79
CB 79
CB 80
CB 80
CB 80
CB 80
CB 80
CB 80
CB 80
CB 80
CB 80
CB 80
CB 80
CB 80
CB 80
CB 80
CB 81
CB 81
CB 81
CB 82
CB 82
section 1
CB02 INDEX
numerical index
Ordering Nr.
Page
Ordering Nr.
Page
Ordering Nr.
Page
Ordering Nr.
Page
Ordering Nr.
Page
Ordering Nr.
Page
Ordering Nr.
09402
09403
09404
09405
09406
09407
09408
09409
09410
09411
09412
09413
09414
09415
09416
09417
09418
09419
09420
09421
09422
09423
09424
09425
09800
09801
09802
09803
09804
09805
09806
09807
09808
09809
09810
09811
09812
09813
09814
09815
09816
09817
09818
09819
09820
09821
09900
09909
09901
09902
09903
09904
09905
09906
09907
09910
09911
09912
09913
09908
09914
09915
09916
09917
09918
09919
10100
10101
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 82
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
10102
10107
10103
10117
10108
10104
10109
10105
10110
10111
10112
10106
10113
10114
10115
10116
09500
09501
09502
09503
09504
09505
09506
09507
09508
09509
09510
09511
09602
09603
09604
09605
09606
09607
09660
09608
09661
09609
09663
09662
09610
09611
09666
09664
09665
09612
09667
09668
09614
09669
09616
09670
09671
09618
09672
09673
09620
09674
09622
09624
09627
09630
09633
09636
09639
09642
09645
09648
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
CB 83
09652
10201
10202
10203
10204
10205
10206
10207
10224
10208
10209
10210
10211
10212
10213
10214
10215
10216
10217
10218
10219
10220
10225
10221
10226
10222
10223
14900
14901
14902
14903
14904
14905
14906
14907
14908
14909
14910
14911
14912
14913
14914
14915
14916
14917
14918
14919
14920
14921
14922
14923
14924
14925
15000
15001
15002
15003
15004
15005
15006
15007
15008
15009
15010
15011
15012
15013
15014
CB 83
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
15015
15016
15017
15018
15019
15020
15021
15022
15023
15024
15025
15100
15101
15102
15103
15104
15105
15106
15107
15108
15109
15110
15111
15112
15113
15114
15115
15116
15117
15118
15119
15120
15121
15122
15123
15124
15125
10402
10403
10404
10405
10406
10407
10408
10409
10410
10411
10412
10413
10414
10416
10418
10440
10441
10442
10443
10444
10445
10446
10447
10448
10420
10422
10424
10427
10430
15200
15201
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 84
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
15202
15203
15204
15205
15206
15207
15208
10800
10809
10810
10823
10802
10811
10812
10803
10813
10804
10814
10805
10806
10807
10808
10815
10816
10817
10818
10819
10820
10821
10822
10600
10607
10608
10601
10609
10610
10602
10611
10603
10612
10604
10605
10613
10606
10614
10615
10616
10617
10618
10619
10620
10621
14808
14810
14811
14800
14812
14801
14802
14813
14803
14814
14804
14805
14809
14806
14807
14815
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 85
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
CB 86
14816
14817
14818
10911
10912
10913
10900
10914
10901
10902
10915
10903
10916
10904
10905
10910
10906
10908
10909
10917
10918
10919
10503
10504
10505
10506
10507
10508
10509
10510
10511
10512
10514
10516
10518
10519
10520
10522
10524
10527
10530
10533
10700
10701
10702
10703
10704
10705
10706
10707
10708
10709
10710
33150
33151
33152
33153
33154
33170
33171
33172
33173
33175
31900
31901
31902
31903
31904
CB 86
CB 86
CB 86
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 87
CB 89
CB 89
CB 89
CB 89
CB 89
CB 89
CB 89
CB 89
CB 89
CB 89
CB 90
CB 90
CB 90
CB 90
CB 90
31905
31906
31907
31908
31909
31940
31800
31801
31802
31803
31804
31805
31806
31807
31808
31809
31810
31811
31812
31813
31815
31816
31817
31818
31819
31820
31821
32000
32001
32002
32003
32004
32005
32006
32007
32008
32009
32010
32010
32019
32200
32201
32202
32203
32204
32205
32209
32490
32491
32492
32493
32494
14620
14621
31600
14440
14200
14201
26600
26601
26602
26650
26651
26652
CB 100
Page
CB 90
CB 90
CB 90
CB 90
CB 90
CB 90
CB 90
CB 90
CB 90
CB 90
CB 90
CB 90
CB 90
CB 90
CB 90
CB 90
CB 90
CB 90
CB 90
CB 90
CB 90
CB 90
CB 90
CB 90
CB 90
CB 90
CB 90
CB 91
CB 91
CB 91
CB 91
CB 91
CB 91
CB 91
CB 91
CB 91
CB 91
CB 91
CB 91
CB 91
CB 91
CB 91
CB 91
CB 91
CB 91
CB 91
CB 91
CB 92
CB 92
CB 92
CB 92
CB 92
CB 94
CB 94
CB 94
CB 95
CB 95
CB 95
CB 96
CB 96
CB 96
CB 96
CB 96
CB 96

4 - Groz Tools

Transcription

Similar documents

Kunst Gestaltendes Werken Textiles Gestalten Niedersachsen

Sa?genkatalog_210207 _NEU_14:Layout 1

Für eine Sortimentsübersicht klicken Sie hier (PDF