docPrisma Plus G - Catalogue 2012
download 
Report Transcription
Prisma Plus G - Catalogue 2012
Low Voltage Prisma Plus G Wall-mounted and floor standing enclosures for Electrical Distribution up to 630 A Catalogue 2012 Table of contents Index Presentation Alphabetical index Catalogue number index > page 2 > page 4 Overview > page 10 IEC 61439 standard Examples of switchboard configurations > page 16 > page 20 Functional system Functional units and distribution > page 32 Accessories > page 56 Distribution > page 66 Circuit breakers > p. 32 Switch-disconnect. > p. 38 Compact NSX 100/630 > p. 32 Easypact EZC 100/400 > p. 36 Front plates, rails, slotted mounting plates > p. 56 Panorama of the solution > p. 66 Manuel srce. changeover system > p. 40 Interpact INS-INV 250/630 > p. 38 Circuit breaker Compact NSX 100/250 > p. 40 Switch-disconnect. Interpact INS-INV250 > p. 41 Fixing accessories > p. 58 Partitioning > p. 59 Cable running > p. 60 Non-Centralised distribution > p. 68 630 A Insulated busbars > p. 68 400 A Rear busbars > p. 70 630 A Multi-stage busbars in duct > p. 72 Prisma Plus G enclosures IP30, IP31, IP43 enclosures > page 91 Pack enclosures Additional information Wall-mounted Floor standing enclosures > p. 94 Combinations > p. 96 Pack wallmounted and flush-mounted enclosures > p. 124 Installation > p. 97 Gland plates > p. 98 Accessories > p. 99 Spare-parts > p. 101 Kilowatt-hour meters > p. 125 Accessories > p. 126 Electrical characteristics Practical Information > page 138 > page 145 Insulated busbars > p. 128 Standards > page 146 Dimensions > p. 104 Distribution blocks > p. 130 Prisma Plus G Index p. 2 Determining catalogue numbers Presentation p. 10 > page 25 Functional system p. 29 Other devices > p. 50 Modular devices > p. 46 Fusegear > p. 42 Fupact INF > p. 42 Fupact ISFT / ISFT-N > p. 44 Switchboard lighting > p. 62 Switchboard incomer > p. 46 Outgoers > p. 47 TeSys, Altistart, Phaseo > p. 48 Kilowatt-hour meters > p. 50 Human-switchboard interface > p. 52 > page 56 Centralised distribution > p. 75 Insulated flexible bars > p. 74 Distribution blocks > p. 75 Comb busbars > p. 82 > page 32 Accessories Management of the internal temperature > p. 64 Finishing parts > p. 63 Functional units and distribution Earth / neutral blocks > p. 83 Earth bars > p. 84 Terminal blocks > p. 86 Terminal blocks layout > p. 87 Distribution > page 66 Prisma Plus G enclosures p. 89 IP55 enclosures > page 107 IP55 enclosures > p. 110 Combinations > p. 111 Accessories > p. 112 Gland plates > p. 113 Partial door > p. 114 Side panels > p. 115 Door accessories > p. 116 Dimensions > p. 134 Accessories > p. 132 Comb busbars, Distribution blocks > p. 131 Spareparts > p. 117 Dimensions > p. 118 Pack enclosures p. 121 Enclosure characteristics Thermal characteristics Practical Information > page 151 > page 159 > page 167 Additional information p. 137 1 Index Alphabetical index Designation 400 A rear busbars 630 A multi-stage busbars in duct A Additional block Adhesive labels for mimic diagrams After-sales service B Barrel locks Blanking plates Brackets C C120 Cable trunking for doors Cable-tie supports Canopy Central uprights Clip-nuts Comb busbars Combination Combination uprights Compact NSX 100/250 Compact NSX 400/630 Connections Connectors Covers D Devices 144 x 144 Devices 72 x 72 Devices 96 x 96 Distribloc Doors E Earth blocks Earthing braid Easypact EZC100/400 F Fan Filters Fixed lighting Flush-mounting kit Flush-mounting kit Front cover support uprights Front-plate Front-plate, Multiclip distribution bloc accessories Fupact INF Fupact ISFT and ISFT-N G Gasket Gland plates Grill with filter Grommets for wiring through front H Handles Heating elements Hexagonal spacers Hook-on rail system Human-switchboard interface I iC120 INS100/160 INS40/160 Inserts Insulated flexible bars Interpact INS-INV250/630 IP30 enclosures IP30 wall-mounted and floor standing enclosures IP55 enclosures J Joinable distribution block K Kilowatt-hour meters 2 Pages 70 72 69 63 101, 102, 103, 117 100, 116 127 97 46 61 61, 132 95, 110, 126 102 58 82, 131 96 127 32, 40 34 129 71 69, 129 54 53, 54 53 77, 130 110 84, 132 100, 132 36 64 64 62 97, 127 97 103 56, 103 103, 117 42 44 95, 126 98, 102, 113, 126 64 61 100, 116 65 58 97 52 46 46 46 100, 116 74 38 94 94 110 79 50, 125 Index Alphabetical index Designation L Lamps Lifting accessories Lifting cross-members Locks M Metal plate with cut-outs Modular devices Modular front-plate Modular incoming fusegear Modular rails Mounting plates Mounting supports Mounting uprights Multiclip Multiclip distribution block Multiple combination Multi-stage distribution block N Neutral bars NG125 NG160 P Padlocking Partial doors Partitioning Plinth cover panel Plinth gusset Plinths Pole Polybloc Power Meter Power supply block Powerclip busbars Prefabricated connections Pushbuttons R Rails Recessed slotted mounting plate Regulating Reinforcement cross-members Resistors S Self-tapping screws Side panels with cut-outs Source changeover system Spare-parts Straps Switchboard portable lamp Symbol sheets T Tap-off block Terminal block Terminal block layout TeSys, Altistart, Phaseo Thermostat Trunking Trunking spreader Trunking supports Universal angle bracket V Ventilated front-plate Vigi C120 Vigi iC120 Vigi NG125 Vigi NG160 Vigilohm Vigilohm system Vigirex W Wall mounting Pages 55 97 97 116 98, 113 46, 103, 117 133 46 133 114 112 111, 112 80 131 111 78, 130 84 46 46 100, 116 99, 114 59 112 112 102 112 75, 76, 130 53 69 68, 128 69 55 57 57, 133 65 112 65 58 115 40 101, 102, 103, 117 60 62 63 69, 129 86 86 48 65 60 98, 126 60 58 64 46 46 46 46 55 54 53, 55 127 3 Index Catalogue number index Cat. no. Designation 01000 01005 01006 01007 01008 01009 01017 01018 01020 01025 01028 Pages 01033 01034 01035 01036 01039 01040 01041 01042 01043 01044 01045 01046 01050 01051 01052 01053 01093 01094 01098 01201 01202 01210 01211 01220 01247 01248 01249 01250 01251 01252 01253 01254 01255 01256 01257 01258 01259 01260 01264 01265 Diagram lines, 10 black mimic, W=900 mm Diagram outgoing arrows, 10 black mimic Diagram incoming arrows, 10 black mimic Diagram transformers, 5 black mimic Diagram earth symbols, 5 black mimic Plain IP30 gland plate System G IP30 accessory FL21 gland plate for Pack enclosures IP55 single struts (2), RAL 9001 Combination piece for IP30 33-module System G floor-standing enclosures Combination piece for IP30 30-module System G floor-standing enclosures Combination piece for IP30 27-module System G floor-standing enclosures Closing accessories for IP30 System G floorstanding enclosures Side for 33-module System G floor-standing enclo. Side for 30-module System G floor-standing enclo. Side for 27-module System G floor-standing enclo. IP30 System G struts (4) System G IP30 support plate for duct, W=300 mm Side for 6-module System G wall-mounted enclo. Side for 9-module System G wall-mounted enclo. Side for 12-module System G wall-mounted enclo. Side for 15-module System G wall-mounted enclo. Side for 18-module System G wall-mounted enclo. Side for 21-module System G wall-mounted enclo. Side for 24-module System G wall-mounted enclo. Accessories for plinth with holes Accessories for plinth Plinth front, 600 mm Plinth front, 300 mm Self adhesive front plate grips (20) Accessories quarter turn closing Washers for System G rear panel (4) IPxxB clipon covers for Powerclip (2) Terminal covers for 200 A Multiclip (4) Powerclip busbar accessories, 160 to 400 A Powerclip busbar accessories, 630 A System G retrofit handle Set of spare parts for IP55 wall-mounted enclo. Set of spare parts for IP55 wall-mounted enclo. IP55 closing system spare parts Plates uprights AFS G 6 m Plates uprights AFS G 9 m Plates uprights AFS G 12 m Plates uprights AFS G 15 m Plates uprights AFS G 18 m Plates uprights AFS G 21 m Plates uprights AFS G 24 m Plates uprights AFS G 27 m Plates uprights AFS G 30 m Plates uprights AFS G 33 m Pack modular device rail AFS Pack decentered plate 4 m AFS Pack decentered plate 4.5 m AFS 03001 Modular device rail 03002 Adjustable modular device rail 03003 03004 Recessed modular device rail Rear modular device rail 03005 03008 03010 03011 DIN rail support (45°) Modular device rail for NG160 Pack Modular device rail, W=250 mm Adjustable modular device rail, W=250 mm 03030 Mount. plate for horizontal fixed NSX-INS250 with toggle Mount. plate for horizontal fixed NSX250 with rotary 32 handle 01029 01030 01032 03000 03031 4 63 63 63 63 63 102 101 102 117 102 102 102 101 95, 102 95, 102 95, 102 101 102 95, 102 95, 102 95, 102 95, 102 95, 102 95, 102 95, 102 102 102 102 102 56, 103, 117 103, 117 101 68, 103, 128 81, 103, 117 68, 103, 128 103 101 117 117 117 103 103 103 103 103 103 103 103 103 103 103, 117 103, 133 103, 133 46, 47, 48, 55, 57 46, 48, 55, 57, 75, 76, 86 49, 57, 133 48, 49, 57, 86, 133 57, 84, 86 133 46, 47, 48, 57 46, 48, 49, 57, 75, 76 32, 38 Cat. no. Designation 03032 03175 03176 03177 03178 03180 03181 03182 03183 03185 03186 03187 03194 03195 03196 03197 03198 03199 03202 03203 Mount. plate for horiz. NSX250 with motor mechanism/plug-in with toggle Mount. plate for horiz. fixed Vigi NSX250 with toggle Mount. plate for vert. fixed NSX250 with toggle Mount. plate for vert. fixed NSX250 with rotary handle Mount. plate for NSX-INS250 source changeover system with rotary handles Mount. plate for vert. fixed NSX-INS250 with toggle, W=250 mm Mount. plate for vert. fixed NSX-INS250 with rotary handle, W=250 mm Mount. plate for horiz fixed NSX630 with toggle Mount. plate for vert. fixed NSX-INS630 with toggle Mount. plate for vert. fixed NSX630 with rotary handle Mount. plate for vert. fixed NSX-INS630 with toggle, W=250 mm Mount. plate for vert. fixed NSX630 with rotary handle, W=250 mm Mounting plate for vertical EZC100, 1P Mounting plate for EZC250 /EZCV250 Mounting plate for EZC400 Mounting plate for INF32/40 Mounting plate for INF63-160 Mounting plate for vertical ISFT100 Mounting plate for ISFT160 Busbar assembly for mounting ISFT100N/160 Mount. plate for vertical ISFT160, W=250 mm Mounting plate for horizontal ISFT250 Mount. plate for vertical ISFT250, W=250 mm Mounting plate for ISFT100N Mounting plate for 2-meter service connection Front plate for 1 3-phase meter in duct Front plate for 3 1-phase meters Mounting plate for 1 3-phase meter in duct Mounting plate for 3 1-phase meters Front plate for 2 3-phase meters Front plate for Gould 3-phase fuses Mounting plate for 2 x 3PH meters 6 modules Clip-nuts for DIN rails, 20 M4 Clip-nuts for DIN rails, 20 M5 Clip-nuts for DIN rails, 20 M6 Slotted mounting plate, 4 modules, for wall-mounted or floor-standing enclosure Recessed slotted mounting plate, 4 modules, wall-mount. or fl.-standing encl. Recessed slotted mounting plate, 6 modules, wall-mount. or fl.-standing encl. Recessed slotted mounting plate, 9 modules, wall-mount. or fl.-standing encl. Slotted mounting plate, 4 modules, W=250 mm Recessed slotted mount. plate, 4 mod., W=250 mm Recessed slotted mount. plate, 6 mod., W=250 mm Recessed slotted mount. plate, 9 mod., W=250 mm Clip-nuts for slotted mounting plates, 20 M4 Clip-nuts for slotted mounting plates, 20 M5 Clip-nuts for slotted mounting plates, 20 M6 Self-tapping screws for functional unit mounting, 20 M5 Hexagonal spacers, H=9 mm, 4 M5 Hexagonal spacers, H=23 mm, 4 M5 Hexagonal spacers, H=55 mm, 4 M5 Captive nuts for M6 hexagonal spacers (20) Hexagonal spacers, H=9mm, 4 M6 Hexagonal spacers, H=23 mm, 4 M6 Hexagonal spacers, H=55 mm, 4 M6 Hexagonal spacers, H=25 mm, 4 M6 Hexagonal spacers, H=40+10mm, 4 M8 Modular front plate, 2 modules Modular front plate, 3 modules 03204 03205 03213 03214 03220 03221 Modular front plate, 4 modules Modular front plate, 5 modules Modular front plate, 3 modules, W=250 mm Modular front plate, 4 modules, W=250 mm Blanking strip, W=1000 mm Divisible blanking plates (4), W=90 mm 03033 03040 03041 03043 03050 03051 03070 03073 03074 03080 03081 03102 03104 03105 03113 03114 03120 03121 03122 03123 03124 03125 03126 03152 03154 03155 03156 03157 03158 03159 03160 03164 03165 03166 03170 03171 03172 03173 Pages 32, 39 32 33, 39 33 40, 41 33, 39 33 34, 38 35, 39 35 35, 39 35 37 36, 37 36, 37 42, 43 42, 43 45 44, 45 45 45 44 45 45 50, 125 50, 125 50 51 50, 125 50 46 51 58 58 58 57 49, 57 49, 57, 125 57 49, 57 57 57 57 57, 58 57, 58 57, 58 58 58, 84 58, 84 58, 84 58 57, 58, 86 57, 58, 86 57, 58, 86 58 58 56 47, 48, 55, 56, 133 46, 47, 56 46, 48, 56, 133 47, 48, 56 46, 47, 56 46, 47, 48, 127 46, 47, 48, 127 Index Catalogue number index Cat. no. Designation 03223 03228 03229 03231 03232 03303 03304 03305 03306 03307 03312 03313 03314 03315 03320 03321 03325 03326 03327 03328 03329 03342 03343 03344 03345 03352 03353 03354 03359 03581 03583 03801 Modular front plate, 3 rows Vertical modular front plate 9 mod. Vertical modular front plate 12 mod. Front plate for horizontal INS250 Front plate for horizontal fixed NSX250 with toggles and rotary handle Front plate for horizontal fixed NSX250 with motor mechanism Front plate for INS250 source changeover system with rotary handles Front plate for 3-4 vertical Vigi NSX250 devices with toggles Front plate for 3-4 vertical NSX250 devices Front plate for 3-4 vertical Vigi NSX250 devices with rotary handles or motor mechanisms Front plate for vertical NSX250 source changeover system with rotary handles Front plate for INS250 complete source changeover assembly Front plate for vertical INS250 Blanking plate for vertical NSX-INS250 Front plate for vertical fixed INS250 with toggle, W=250 mm Front plate for vertical fixed NSX250 with rotary handle, W=250 mm Front plate for horizontal INS630 Front plate for vertical INS630 Front plate for vertical NSX630 with rotary handle or motor mechanism Front plate for vertical fixed INS630 with toggle, W=250 mm Front plate for vertical NSX630 with rotary handle or motor mechanism, W=250 mm Front plate for horizontal plug-in NSX250 with toggle Front plate for horiz.fixed manual Vigi NSX250 Front plate for vertical fixed manual Vigi NSX250, W=250 mm Front plate for horiz. fixed NSX630 with toggle Front plate for vertical Vigi NSX630 Front plate for vertical fixed manual NSX630, W=250 mm Front plate for vertical fixed manual Vigi NSX630, W=250 mm Front plate for vertical EZC100 Front plate for horizontal EZC250/EZCV250 Front plate for vertical EZC250/EZCV250 Front plate for horizontal EZC400 Front plate for vertical EZC400 Front plate for vertical INF32/40, 3P Front plate for INF32/40, 4P and horiz. 3P Front plate for INF63-160, 3P and vert. INV63, 3P Front plate for vert. INF63, 4P and vert. INF160 Front plate for vertical ISFT100 Front plate for vertical ISFT160 Front plate for vertical ISFT100N Front plate for horizontal ISFT160 Front plate for horizontal ISFT160, W=250 mm Front plate for horizontal ISFT250 Front plate for vertical ISFT250, W=250 mm Transparent front plate, 4 modules Transparent front plate, 6 modules Transparent front plate, 9 modules Transparent front plate, 12 modules Transparent front plate, 4 modules,W=250 mm Transparent front plate, 6 modules,W=250 mm Transparent front plate, 9 modules,W=250 mm Front plate for Gould 1-phase fuses Universal angle brackets (2) Universal angle brackets (6) Plain front plate, 1 module 03802 Plain front plate, 2 modules 03234 03235 03241 03243 03244 03245 03247 03248 03249 03251 03253 03271 03274 03275 03281 03283 03290 03292 03293 03296 03297 03298 03299 Pages Cat. no. Designation 47, 56 47 47 38 32 03803 Plain front plate, 3 modules 03804 03805 03806 Plain front plate, 4 modules Plain front plate, 5 modules Plain front plate, 6 modules 32 03807 03808 03811 Plain front plate, 9 modules Plain front plate, 12 modules Plain front plate, 1 module, W=250 mm 03812 03813 03814 03815 03816 03817 03890 03891 03895 03900 03901 03902 03903 03904 03907 03908 03910 03911 03912 Plain front plate, 2 modules, W=250 mm Plain front plate, 3 modules, W=250 mm Plain front plate, 4 modules, W=250 mm Plain front plate, 5 modules, W=250 mm Plain front plate, 6 modules, W=250 mm Plain front plate, 9 modules, W=250 mm Front plate for fan or grill IP30 ventilated front plate, 1 module IP30 ventilated front plate, 3 modules Plain mounting plate for 72 x 72 mm meter Plain mounting plate for 96 x 96 mm meter Mounting plate with cut-out for 72 x 72 mm meter Mounting plate with cut-out for 96 x 96 mm meter Front plate with cut-outs for meter mount. plates Blanking plate, 72 x 72 Blanking plate, 96 x 96 for meters Front plate with cut-outs for 72 x 72 mm meters Front plate with cut-outs for 96 x 96 mm meters Front plate with cut-outs for 144 x 144 mm + 4 72 x 72 mm meters Front plate 96 x 96 for 1 device Front plate with holes for 22 mm dia. pushbuttons and lamps Visor for human/switchboard interface (HSI) Front plate for Vigilohm TR22A + 6 72 x 72 mm meters 41 33 33 33 40 41 39 37 39 33 38 39 35 39 35 32 32 33 34 35 35 35 37 36 37 36 37 43 42, 43 42, 43 43 45 45 45 44 45 44 45 48, 49, 55, 56 50, 51, 55, 56 50, 55, 56 55, 56 48, 49, 56 56 51, 56 46 58 58 32, 33, 35, 38, 39, 44, 45, 48, 49, 56 32, 33, 35, 39, 40, 41, 42, 43, 44, 45, 56 03913 03914 03928 03934 04000 04000 04008 04012 04013 04014 04018 04021 04024 04029 04030 04031 04033 04034 04037 04040 04041 04045 04046 04047 04052 04053 04054 04055 04060 04061 04062 04064 04065 04066 Multiclip distribution block, 4P, 80 A Multiclip distribution block, 4P, 63A, 1/2 row Multiclip distribution block, 2P, 200A, 1 row Multiclip distribution block, 3P, 200A, 1 row Multiclip distribution block, 4P, 200A, 1 row Multiclip distribution block, 4P, 160A, 1/2 row Powerclip busbar connection for 200 A Multiclip distribution block Duct busbar connection for 200 A Multiclip distribution block Rear busbar connection for 200 A Multiclip distribution block Multiclip/NG160 connection, 200 A Polybloc distribution block, 1P, 160 A Polybloc distribution block, 3P, 250 A Polybloc distribution block, 4P, 250 A Spacers Cu for Polybloc 250A distribution block (4) Distribloc 63 (top connection) Distribloc 63 (bottom connection) Distribloc 125 Distribloc 160 + connections Connections (4) between NG-INS125 and Distribloc distribution block Multi-stage distribution block, 4P, 160 A Multi-stage distribution block, 4P, 250 A Multi-stage distribution block, 4P, 400 A Multi-stage distribution block, 4P, 630 A Power supply block for horizontal NSX250 Universal power supply block, 250 A Connection between vertical NSX-INS250 and universal power supply block Connection between vertical NSX-INS250 in duct and universal power supply block Connection between vertical NSX-INS250 in duct and busbars Incoming connection block for NSX-INS250 supplied via the top Pages 34, 35, 38, 40, 48, 56 35, 49, 56 49, 56 39, 49, 50, 51, 56 50, 56 56 35, 46, 48, 49, 56 35, 39, 56 48, 56 49, 56 56 56 51, 56 56, 64 56, 64 56, 64 53 53 53 53 53 53, 54 53 53 53 54 53 55 53 54 80, 131 80, 131 81 81 81 81 69, 81 73, 81 71, 81 81 75, 130 76 76 76 77, 130 77, 130 77, 130 77, 130 77, 130 78 78 78 78 69 69 69 69 73 38 5 Index Catalogue number index Cat. no. Designation 04067 04070 04071 04073 04074 04075 04076 04103 04104 04107 04108 04111 04112 04113 04114 04116 04117 04118 04119 04121 04122 04123 04124 04126 04127 04128 04129 04145 04146 04147 04148 04149 04150 04151 04152 04155 04156 04158 04161 04162 04163 04171 04172 04173 04174 04190 04191 04192 04194 04195 04197 04198 04200 04201 04202 04205 04206 04207 04208 04210 04214 04215 04220 04223 04224 04226 6 Incoming connection block for NSX-INS250 supplied via the bottom Power supply block for horizontal NSX400 Power supply block for horizontal NSX630 Connection between vertical NSX-INS400-630 in duct and universal power supply block Universal power supply block, 400-630 A Connection between vertical NSX-INS630 in duct and busbars In-duct incoming connection block for NSX630 Powerclip busbars, 125 A, 3P, W=450 mm Powerclip busbars, 125 A, 4P, W=450 mm Powerclip busbars, 125 A, 3P, W=750 mm Powerclip busbars, 125 A, 4P, W=750 mm Powerclip busbars, 160 A, 3P, W=1000 mm Powerclip busbars, 250 A, 3P, W=1000 mm Powerclip busbars, 400 A, 3P, W=1000 mm Powerclip busbars, 630 A, 3P, W=1000 mm Powerclip busbars, 160 A, 3P, W=1400 mm Powerclip busbars, 250 A, 3P, W=1400 mm Powerclip busbars, 400 A, 3P, W=1400 mm Powerclip busbars, 630 A, 3P, W=1400 mm Powerclip busbars, 160 A, 4P, W=1000 mm Powerclip busbars, 250 A, 4P, W=1000 mm Powerclip busbars, 400 A, 4P, W=1000 mm Powerclip busbars, 630 A, 4P, W=1000 mm Powerclip busbars, 160 A, 4P, W=1400 mm Powerclip busbars, 250 A, 4P, W=1400 mm Powerclip busbars, 400 A, 4P, W=1400 mm Powerclip busbars, 630 A, 4P, W=1400 mm Connections, 125 A (4) Connections 160 A (4) Busbar/modular device connection, 160 A Busbar/Vigi modular device connection, 160 A Modular device/Polybloc connection, 160 A Covers for Powerclip busbars, 8 IPxxB Powerclip tap-off blocks with 6 mm² + 10 mm² terminals (12) Powerclip tap-off blocks with 16mm² terminals (12) Additional 35mm² block, 3P Additional 35mm² block, 4P Screws for Powerclip busbars (20) Bars with threaded holes (4), 160 A, W=1000 mm Bars with threaded holes (4), 250 A, W=1000 mm Bars with threaded holes (4), 400 A, W=1000 mm Bars with threaded holes (4), 160 A, W=1000 mm Bars with threaded holes (4), 250 A, W=1000 mm Bars with threaded holes (4), 400 A , W=1000 mm Bars with threaded holes (4), 630 A, W=1000 mm Copper angle brackets (4), 250A Rear busbar support Multi-stage bar support for duct Bolts for 5 mm bars, 20 M6 x 20mm Screws for bars with threaded holes, less than 630 A, 40 M6 x 16 mm Busbar power supply barrier, 630 A Rear busbar barrier Earth bar, 24 modules Earth bar for direct earth blocks, 12 x 3 mm Earth bars (2), 12 modules Supports for earth bar on DIN rail (2) Fixing brackets for vert. earth bar in wall-mount. or fl.-standing encl. H 15 mm Fixing brackets for vert. earth bar in wall-mount. or fl.-standing encl. H 45 mm Fixing brackets for vert. earth bar in wall-mount. or fl.-standing encl. H 80 mm Kit for neutral bar Earth blocks with 12x4mm² spring terminals (4) Earth blocks with 3x16mm² spring terminals (4) Mount. plate for terminal block and earth bar in duct Mount. plate with 4 vertical DIN rails for terminal blocks Raisers, 5 Practic Modular device rail, W=1600 mm Pages 38 69 69 69 69 73 34 128 128 128 128 68, 128 68 68 68 68 68 68 68 68, 126 68 68 68 68 68 68 68 69, 71, 129 69, 71, 129 69, 129 69, 129 75, 130 69, 129 69, 129 69, 129 69 69 69, 129 70, 72 70, 72 70, 72 70, 72 70, 72 70, 72 72 71 70 72 71, 73 71, 73 72 70 84, 132 84, 132 84 84 57, 84, 85, 86, 132 57, 84, 85, 86 57, 84, 85, 86 84 84, 132 84, 132 85, 87 85, 87 56 47, 57 Cat. no. Designation 04227 04233 04234 04235 04239 04243 04255 04256 04257 04263 04264 04265 04267 04330 04331 Pages 04332 04333 04742 04743 04746 04751 04752 04753 Rail and raisers modular Trunking for door, W=2000 mm Grommets for wiring through front (10) Flexible trunking for wiring to door Horizontal cable straps (12) Covers for horizontal cable straps (4) Horizontal trunking supports (12) Adaptable support for horizontal trunking (10) Horiz. trunking sections (4), W=450 mm, + supports Covers for vertical cable straps (2), W=1000 mm Vertical cable straps, System G (12) Vertical trunking supports (12) Vertical trunking, W=2000 mm Vertical partition Horizontal partition for wall-mounted or floor-standing enclosure Horizontal partition for duct Horizontal partition for Pack enclosure Insulated flexible bar 20 x 2 mm, W=1800 mm Insulated flexible bar 20 x 3 mm, W=1800 mm Insulated flexible bar 24 x 5 mm, W=1800 mm Insulated flexible bar 32 x 5 mm, W=1800 mm Insulated flexible bar 32 x 6 mm, W=1800 mm Insulated flexible bar 32 x 8 mm, W=1800 mm 46, 57, 133 61 61 61 60, 132 60, 132 60, 132 60, 132 60, 132 60 60 60 60 59 46, 50, 51, 59 51, 59 125 71, 73, 74 71, 73, 74 71, 73, 74 71, 73, 74 71, 73, 74 71, 73, 74 07051 07052 07053 Cable connectors (4), 160 A, 70 mm² Cable connectors (4), 250 A, 185 mm² Cable connectors (4), 400 A, 300 mm² 71 71 71 08002 08003 08004 08005 08006 08012 08013 08082 08083 08084 08085 08086 08092 08093 08094 08095 08096 08102 08103 08104 08105 08106 08107 08108 08109 08122 08123 08124 08125 08126 08127 08128 08132 08133 08134 08135 08136 08137 08138 08172 08173 08174 08175 08176 Surface-mount Pack enclosure, W=550 mm, 2 rows Surface-mount Pack enclosure, W=550 mm, 3 rows Surface-mount Pack enclosure, W=550 mm, 4 rows Surface-mount Pack enclosure, W=550 mm, 5 rows Surface-mount Pack enclosure, W=550 mm, 6 rows Pack extension enclosure, 2 rows Pack extension enclosure, 3 rows Plain door for Pack enclosure, W=550 mm, 2 rows Plain door for Pack enclosure, W=550 mm, 3 rows Plain door for Pack enclosure, W=550 mm, 4 rows Plain door for Pack enclosure, W=550 mm, 5 rows Plain door for Pack enclosure, W=550 mm, 6 rows Transparent door for Pack enclos., W=550 mm, 2 rows Transparent door for Pack enclos., W=550 mm, 3 rows Transparent door for Pack enclos., W=550 mm, 4 rows Transparent door for Pack enclos., W=550 mm, 5 rows Transparent door for Pack enclos., W=550 mm, 6 rows Wall-mounted enclosure, W=600 mm, 6 modules Wall-mounted enclosure, W=600 mm, 9 modules Wall-mounted enclosure, W=600 mm, 12 modules Wall-mounted enclosure, W=600 mm, 15 modules Wall-mounted enclosure, W=600 mm, 18 modules Wall-mounted enclosure, W=600 mm, 21 modules Wall-mounted enclosure, W=600 mm, 24 modules Wall-mounted enclosure, W=600 mm, 27 modules Plain door for wall-mounted enclosure, 6 modules Plain door for wall-mounted enclosure, 9 modules Plain door for wall-mounted enclosure, 12 modules Plain door for wall-mounted enclosure, 15 modules Plain door for wall-mounted enclosure, 18 modules Plain door for wall-mounted enclosure, 21 modules Plain door for wall-mounted enclosure, 24 modules Transp. door for wall-mounted enclos., 6 modules Transp. door for wall-mounted enclos., 9 modules Transp. door for wall-mounted enclos., 12 modules Transp. door for wall-mounted enclos., 15 modules Transp. door for wall-mounted enclos., 18 modules Transp. door for wall-mounted enclos., 21 modules Transp. door for wall-mounted enclos., 24 modules Duct for wall-mounted enclos., W=300 mm, 6 mod. Duct for wall-mounted enclos., W=300 mm, 9 mod. Duct for wall-mounted enclos., W=300 mm, 12 mod. Duct for wall-mounted enclos., W=300 mm, 15 mod. Duct for wall-mounted enclos., W=300 mm, 18 mod. 124 124 124 124 124 124 124 124 124 124 124 124 124 124 124 124 124 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94 94, 95 94, 95 94, 95 94, 95 94, 95 07000 08000 Index Catalogue number index Cat. no. Designation 08177 08178 08179 08182 08183 08184 08185 08186 08187 08188 08197 08198 08202 08203 08204 08212 08213 08214 08222 08223 08224 08232 08233 08234 08272 08273 08274 08282 08283 08284 08292 08293 08294 08302 08303 08304 08305 08306 08307 08309 08312 08313 08314 08315 08316 08317 08319 08322 08323 08324 08325 08326 08327 08329 08332 08333 08334 08335 08336 08337 08339 08342 08343 08344 08345 08346 08347 08349 08352 08353 Duct for wall-mounted enclos., W=300 mm, 21 mod. Duct for wall-mounted enclos., W=300 mm, 24 mod. Duct for wall-mounted enclos., W=300 mm, 27 mod. Door for wall-mounted enclosure duct, 6 modules Door for wall-mounted enclosure duct, 9 modules Door for wall-mounted enclosure duct, 12 modules Door for wall-mounted enclosure duct, 15 modules Door for wall-mounted enclosure duct, 18 modules Door for wall-mounted enclosure duct, 21 modules Door for wall-mounted enclosure duct, 24 modules Transp. door for wall-mounted enclos. duct, 21 mod. Transp. door for wall-mounted enclos. duct, 24 mod. Floor-standing enclosure, W=600 mm, 27 modules Floor-standing enclosure, W=600 mm, 30 modules Floor-standing enclosure, W=600 mm, 33 modules Floor-standing enclos. extension, W=600 mm, 27 mod. Floor-standing enclos. extension, W=600 mm, 30 mod. Floor-standing enclos. extension, W=600 mm, 33 mod. Plain door for wall-mounted and floor-standing enclosure, 27 modules Plain door for floor-standing enclosure, 30 modules Plain door for floor-standing enclosure, 33 modules Transparent door for wall-mounted and floorstanding enclosure, 27 modules Transp. door for floor-standing enclos., 30 modules Transp. door for floor-standing enclos., 33 modules Duct for floor-standing enclos., W=300 mm, 27 mod. Duct for floor-standing enclos., W=300 mm, 30 mod. Duct for floor-standing enclos., W=300 mm, 33 mod. Door for wall-mounted and floor-standing enclosure duct, 27 modules Door for floor-standing enclosure duct, 30 modules Door for floor-standing enclosure duct, 33 modules Transparent door for wall-mounted and floor-standing enclosure duct, 27 modules Transp. door for floor-standing enclos. duct, 30 mod. Transp. door for floor-standing enclos. duct, 33 mod. IP55 enclosure, 7 modules IP55 enclosure, 11 modules IP55 enclosure, 15 modules IP55 enclosure, 19 modules IP55 enclosure, 23 modules IP55 enclosure, 27 modules IP55 enclosure, W=850 mm, 33 modules IP55 enclosure extension, 7 modules IP55 enclosure extension, 11 modules IP55 enclosure extension, 15 modules IP55 enclosure extension, 19 modules IP55 enclosure extension, 23 modules IP55 enclosure extension, 27 modules IP55 enclosure extension, 33 modules IP55 plain door, 7 modules IP55 plain door, 11 modules IP55 plain door, 15 modules IP55 plain door, 19 modules IP55 plain door, 23 modules IP55 plain door, 27 modules IP55 plain door, 33 modules IP55 transparent door, 7 modules IP55 transparent door, 11 modules IP55 transparent door, 15 modules IP55 transparent door, 19 modules IP55 transparent door, 23 modules IP55 transparent door, 27 modules IP55 transparent door, 33 modules IP55 duct, W=300 mm, 7 modules IP55 duct, W=300 mm, 11 modules IP55 duct, W=300 mm, 15 modules IP55 duct, W=300 mm, 19 modules IP55 duct, W=300 mm, 23 modules IP55 duct, W=300 mm, 27 modules IP55 duct, W=300 mm, 33 modules IP55 side panels, 7 modules IP55 side panels, 11 modules Pages Cat. no. Designation 94, 95 94, 95 94, 95 94, 95 94, 95 94, 95 94, 95 94, 95 94, 95 94, 95 94, 95 94, 95 94 94 94 94 94 94 94 08354 08355 08356 08357 08359 08362 08363 08364 08365 08366 08367 08369 08371 08372 08374 94 94 94 08377 94 94 94, 95 94, 95 94, 95 94, 95 94, 95 94, 95 94, 95 94, 95 94, 95 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 110 08375 08376 08381 08382 08383 08384 08386 08387 08391 08392 08393 08394 08395 08396 08585 08783 08801 08803 08804 08805 08807 08811 08812 08813 08814 08815 08816 08817 08818 08819 08820 08821 08822 08823 08824 08826 08827 08830 08831 08832 08833 08841 08850 IP55 side panels, 15 modules IP55 side panels, 19 modules IP55 side panels, 23 modules IP55 side panels, 27 modules IP55 side panels, 33 modules IP55 side panels with cut-outs, 7 modules IP55 side panels with cut-outs, 11 modules IP55 side panels with cut-outs, 15 modules IP55 side panels with cut-outs, 19 modules IP55 side panels with cut-outs, 23 modules IP55 side panels with cut-outs, 27 modules IP55 side panels with cut-outs, 33 modules Top and bottom plates, W=600 mm Top and bottom plates, W=300 mm IP55 4-module partial plain door for 11-27 module enclosures IP55 6-module partial plain door for 33-module enclosures IP55 4-module partial door with cut-outs for 11-27 module enclosures IP55 6-module partial door with cut-outs for 33-module enclosures IP55 horizontal/vertical combination kit IP55 L combination kit IP55 square combination kit IP55 vertical partition Canopy for IP55 wall-mounted or floor-standing enclosure, W = 600 mm Canopy for IP55 duct, W = 300 mm IP55 mounting upright IP55 plinth gusset IP55 plinth cover panels, W=600 mm IP55 plinth cover panels, W=300 mm Pole-mount kit for enclosures IP55 lifting rings 52° Front plate hinge kit (set of 2 hinges) Form C cable-tie support W=1600 Lifting rings (2) External wall-mounted brackets (4) for Pack enclos. External wall-mounted brackets (4) Plinth raiser for floor-standing enclosures, 100 mm Plinth raiser for ducts, 100 mm Lifting/reinforcement cross-members (2) for 2 wall-mounted or floor-standing enclosures Lifting/reinforcement cross-members (2) for single wall-mounted or floor-standing enclosure and duct Lifting-reinf. cross-members (2) for wall-mount. or fl.-standing encl. + ducts Lifting/reinforcement cross-members (2) for duct + enclos. + duct + enclos. or duct + enclos. + enclos. + duct IP30 combination kit for floor-standing enclosures Combination kit Combination uprights (2) Multiple combination kit Flush-mounting kit, 6 to 18 modules Flush-mounting kit, 21 to 27 modules Trunking spreader for Pack enclosure Pack flush-mount kit Pack IP31 canopy Trunking spreader for wall-mounted or floor-standing enclosure Lifting/reinforcement cross-members (2) for duct + enclosure + duct + enclosure + duct Canopy for duct + single wall-mounted or floor-standing enclosure + duct, IP31 IP31 canopy for 2 wall-mounted or 2 floor-standing enclosures Canopy for 2 wall-mounted or 2 floor-standing associated enclosures, IP31 Canopy for floor-standing enclosure, IP31 Canopy for enclosure + duct + enclosure, IP31 IP43 door gasket kit, 6-33 modules Partial door for wall-mounted or floor-standing enclosure, 6-module Pages 110 110 110 110 110 115 115 115 115 115 115 115 110 110 114 114 114 114 111 111 111 59 110 110 111, 112 112 112 112 112 111 56 61 97 127 97 97 97 96, 97 96, 97 96, 97 96, 97 96 96 96, 127 96 97 97 126 127 126 98 96 95 95 95 95 95 95, 126 99 7 Index Catalogue number index Cat. no. Designation 08851 08861 08862 08863 08864 08866 08867 08868 08870 08871 08872 08874 08875 08876 08878 08879 08880 08881 08882 08884 08887 08888 08891 08892 08895 08896 08897 08898 08899 08900 08903 08904 08905 08906 08910 08911 08913 08914 08915 08916 08917 08918 08931 08932 08933 08934 08935 08936 08938 08939 08940 08941 08942 08943 08944 08945 08946 08947 08948 08949 08950 08951 08952 08953 08955 08956 8 Partial door with cut-out for human/switchboard interface (HSI) for wall-mounted or floorstanding enclosure, 6-module Plain mounting plate, 210 x 150 mm Mounting plate with eight 22 mm diameter holes Mounting plate with two 65 x 85 mm holes for industrial sockets IP55 mounting plate with 65 x 85 mm and 90 x 100 mm holes for industrial sockets Cable tie support adapter Cable tie supports for wall-mounted or floor-standing enclosure (2) Cable tie supports for ducts (4) Plain metal gland plate for wall-mounted or floor-standing enclosure Interface for gland plate for wall-mounted or floor-standing enclosure Membrane-type gland plate, 25 entries Plain metal gland plate for duct Interface for gland plate for duct IP55 gland plate interface Plastic gland plate and interface for Pack enclosures Plain metal gland plate for Pack enclosures Plastic gland plate and interface for wall-mounted or floor-standing enclosure Plain gland plate Plain plate for wall-mounted and floor-standing enclos. Plastic gland plate and interface for ducts Gland plate for floor-standing enclosure plinth Gland plate for duct plinth Knockout gland plate with 4xM12/20 + 4xM16/25 Knockout gland plate with 2xM20/32 + 2xM25/40 Gland plate with 13 knockouts Membrane-type gland plate, 35 entries Membrane-type gland plate, 2 entries Gland plate 39 incoming 7/26 IP55 Gland plate 2 incoming 33/72 IP55 Switchboard identification plate Adhesive label holders (12), H=24 mm, W=432 mm Adhesive label holders (12), H=36 mm, W=432 mm Adhesive label holders (12), H=24 mm, W=180 mm Adhesive label holders (12), H=36 mm, W=180 mm Earthing braid, 6 mm² Earthing wire, 6 mm² Clip-on labels (12), 18 x 35 mm Engraving plates (12), 18 x 35 mm Clip-on labels (12), 18 x 72 mm Engraving plates (12), 18 x 72 mm Clip-on labels (12), 25 x 85 mm Engraving plates (12), 25 x 85mm Standard handle, Ral 7016 EURO handle without insert Handle without insert, ASSA-ABLOY Handle for cylinder, EURO, IP55 Handle, IP55, L = 155 mm IP55 door latch with lock and 2 no. 405 keys Handle padlocking kit IP55 handle padlocking kit Barrel lock no. 405 Barrel lock no. 455 Barrel lock no. 1242E Barrel lock no. 3113A Barrel lock no. 2433A DIN double bar insert Screwdriver slot insert Triangle insert, 6.5 mm male Triangle insert, 7 mm male Triangle insert, 8 mm male Triangle insert, 9 mm male Square insert, 6 mm male Square insert, 7 mm male Square insert, 8 mm male Square insert, 6 mm female Barrel lock no. 2432E Pages 99 114 114 114 114 61 32, 61, 132 61 98, 113 98 98, 113 98 98 113 126 126 98 98, 113 96 98 97, 98, 113 98 98, 113 113 98, 113 98, 113 98, 113 113 113 63 63 63 63 63 51, 100, 132 125 63 63 63 63 63 63 100 100 100 116 116 116 100 116 100, 116 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 Cat. no. Designation Pages 08961 08963 08964 08965 08987 08988 08989 08990 08992 08993 08994 08998 Touch-up paint brush Adhesive drawing holder Switchboard lighting Switchboard portable lamp Fan Grill with filter Filters, 5 standard Filters, 5 fine Resistor, 55 W Resistor, 90 W Resistor, 250 W Thermostat 63 63 62 62 64 64 64 64 65 65 65 65 09931 09932 09933 09934 09937 09939 09942 09943 09945 09946 09947 09948 09949 09981 09982 09983 09984 09985 09986 09987 09988 09989 Slot handle insert IP55 for screwdriver Double bar handle insert IP55, 3 mm IP55 barrel + 2 no. 2433 A keys IP55 8 mm male triangle insert for handle (CNOMO) IP55 7 mm male triangle insert for handle IP55 9 mm male triangle insert for handle IP55 barrel + 2 no. 1242E keys IP55 barrel + 2 no. 3113A keys IP55 barrel + 2 no. 455 keys IP55 6 mm female square insert for handle IP55 7 mm male square insert for handle IP55 8 mm male square insert for handle IP55 6 mm male square insert for handle IP55 screwdriver slot insert for door IP55 3 mm double bar insert for door IP55 7 mm male triangle insert for door IP55 8 mm male triangle insert for door (CNOMO) IP55 9 mm male triangle insert for door IP55 6 mm male square insert for door IP55 7 mm male square insert for door IP55 8 mm male square insert for door IP55 6 mm female square insert for door 116 116 116 116 116 116 116 116 116 116 116 116 116 116 116 116 116 116 116 116 116 116 13142 115 13506 13507 13508 13510 13512 13514 13515 13516 13517 13518 13735 13736 Installation accessory for Kaedra enclosure: 103 x 225 mm plate - 2 openings Installation accessory for Kaedra enclosure: 103 x 225 mm plate - for 65 x 65 or 75 x 75 mm outlet Installation accessory for Kaedra enclosure: 103 x 225 mm plate - for 100 x 107 mm outlet Two-pole multi-stage distrib. block, 100 A (2 x 7 holes) Two-pole multi-stage distrib. block, 125 A (2 x 13 holes) Four-pole multi-stage distrib. block, 40 A (4 x 13 holes) Four-pole multi-stage distrib. block, 100 A (4 x 7 holes) Four-pole multi-stage distrib. block, 125 A (4 x 13 holes) Four-pole multi-stage distrib. block, 125 A (4 x 17 holes) Additional neutral bar for cat. no. 13508 Additional neutral bar for cat. no. 13510 Additional neutral bar for cat. no. 13512 Additional neutral bar for cat. no. 13514 Self-adhesive label sheets for common symbols (10) Self-adhesive label sheets for special symbols (10) 14811 14812 14813 14814 14818 14881 14882 14883 14884 14885 14886 14887 14888 14891 14892 14893 14894 Comb busbar (W=430 mm, 16 poles) 1P Comb busbar (W=430 mm, 16 poles) 2P Comb busbar (W=430 mm, 16 poles) 3P Comb busbar (W=430 mm, 16 poles) 4P Tooth caps (set of 20) Comb busbar, 24-module (9 mm modules) 1P Comb busbar, 24-module (9 mm modules) 2P Comb busbar, 24-module (9 mm modules) 3P Comb busbar, 24-module (9 mm modules) 4P Insulated connectors for 25 mm² cables (4) End-caps 1P/2P/1P + N, for comb busbars (40) End-caps 3P/4P/3P + N, for comb busbars (40) Tooth-caps for comb busbar teeth (40) Comb busbars, 2 48-module (9 mm modules) 1P Comb busbars, 2 48-module (9 mm modules) 2P Comb busbars, 2 48-module (9 mm modules) 3P Comb busbars, 2 48-module (9 mm modules) 4P 82 82 82 82 82 82, 131 82, 131 82, 131 82, 131 82, 131 82, 131 82 82, 131 82, 131 82, 131 82, 131 82, 131 09000 13000 13143 13144 14000 115 115 79, 130 79, 130 79, 130 79, 130 79, 130 79, 130 79, 130 79, 130 79, 130 79, 130 63 63 Index Cat. no. Catalogue number index Designation Pages 14936 14937 14938 14939 80A joinable distribution block 1P - 25 and 16 mm² 80A joinable distribution block 2P - 25 and 16 mm² 80A joinable distribution block 1P - 35 and 25 mm² 80A joinable distribution block 2P - 35 and 25 mm² 79 79 79 79 21086 21088 21089 21090 21092 21093 21094 21095 21096 21098 comb busbar for DPN - 2P - 24 mod (9mm) comb busbar for DPN - 2P - 48 mod (9mm) comb busbar for DPN - 2P - 96 mod (9mm) comb busbar for DPN - 3P - 24 mod (9mm) comb busbar for DPN - 3P - 48 mod (9mm) comb busbar for DPN - 3P - 96 mod (9mm) lateral tooth-caps - 2P lateral tooth-caps - 3P Tooth-caps (12) Insulated connectors (4) 82, 131 82, 131 82, 131 82, 131 82, 131 82, 131 82, 131 82, 131 82, 131 82, 131 28947 28948 lateral tooth-caps - 2P lateral tooth-caps - 3P Tooth-caps (12) 69, 129 69, 129 29324 29358 29359 Long terminal shield INS-INV 250 Coupling accessory NSX 100/250-3P Coupling accessory NSX 100/250-4P 38, 39, 41 40, 41 40, 41 31064 31073 31140 31141 31142 31143 31144 31145 31146 31147 Raiser Mechanical interlocking Source changeover assembly-100A-3P Source changeover assembly-100A-4P Source changeover assembly-200A-3P Source changeover assembly-200A-4P Source changeover assembly-160A-3P Source changeover assembly-160A-4P Source changeover assembly-250A-3P Source changeover assembly-250A-4P 41 41 41 41 41 41 41 41 41 41 32565 Long terminal shield INS-INV 320/630 38, 39 49658 49659 49869 49872 Long terminal shield Fupact INF40/60 Long terminal shield Fupact INF100/160 Long terminal shield Fupact ISFT160-3P Long terminal shield Fupact ISFT250-3P 42, 43 42, 43 44, 45 44, 45 Stop plate for markers 2-pole commoning link for 35 mm² screw term.block 2-pole commoning link for 70 mm² screw term.block 2-pole commoning link for 150 mm² screw term.block Markers - 6 mm pitch Markers - 6 mm pitch Markers - 6 mm pitch Markers - 6 mm pitch Markers - 6 mm pitch Markers - 6 mm pitch Markers - 6 mm pitch Markers - 6 mm pitch Markers - 6 mm pitch Markers - 6 mm pitch Markers - 6 mm pitch Markers - 8 mm pitch Markers - 8 mm pitch Markers - 8 mm pitch Markers - 8 mm pitch Markers - 8 mm pitch Markers - 8 mm pitch Markers - 8 mm pitch Markers - 8 mm pitch Markers - 8 mm pitch Markers - 8 mm pitch Markers - 6 mm pitch Markers - 8 mm pitch Markers - 6 mm pitch 87 86 21000 28000 29000 31000 32000 49000 AB1 AB1 AB8P35 AB1 ALN352 AB1 ALN702 AB1 ALN1502 AB1 B6L1 AB1 B6L2 AB1 B6L3 AB1 B610 AB1 B620 AB1 B630 AB1 B640 AB1 B650 AB1 B660 AB1 B680 AB1 B690 AB1 B810 AB1 B820 AB1 B830 AB1 B840 AB1 B850 AB1 B860 AB1 B870 AB1 B880 AB1 B890 AB1 B6100 AB1 B670 AB1 B8100 AB1 BV6 86 86 87 87 87 87 87 87 87 87 87 87 87 87 87 87 87 87 87 87 87 87 87 87 87 87 Cat. no. Designation Pages AB1 BV6BM AB1 BV6RP AB1 BV8 AB1 RRAL42 AB1 RRAL102 AB1 RRAL162 AB1 RRN435U2BL AB1 RRN435U2GR AB1 RRN435U3BL AB1 RRN435U3GR AB1 RRN635U2BL AB1 RRN635U2GR AB1 RRN1035U2BL AB1 RRN1035U2GR AB1 RRN1635U2BL AB1 RRN1635U2GR AB1 RRNAC442BL AB1 RRNAC442GR AB1 RRNAC443BL AB1 RRNAC443GR AB1 RRNAC643BL AB1 RRNAC643GR AB1 RRNAC1042BL AB1 RRNAC1042GR AB1 RRNAC1642BL AB1 RRNAC1642GR AB1 RRNAL62 AB1 RRNTP435U2 AB1 RRNTP435U3 AB1 RRNTP635U2 AB1 RRNTP1035U2 AB1 RRNTP1635U2 AB1 RRNTPAC442 AB1 RRNTPAC443 AB1 RRNTPAC642 AB1 RRNTPAC1042 AB1 RRNTPAC1642 AB1 S1 AB1 VVN3535U AB1 VVN3535UBL AB1 VVN7035U AB1 VVN7035UBL AB1 VVN15035U AB1 VVN15035UBL Markers - 6 mm pitch Markers - 6 mm pitch Markers - 8 mm pitch 2-pole insulated commoning link - 4 mm² 2-pole insulated commoning link - 10 mm² 2-pole insulated commoning link - 16 mm² Terminal block 1in/1out-blue-4 mm² Terminal block 1in/1out-grey-4 mm² Terminal block 1in/2out-blue-4 mm² Terminal block 1in/3out-grey-4 mm² Terminal block 1in/1out-blue-6 mm² Terminal block 1in/1out-grey-6 mm² Terminal block 1in/1out-blue-10 mm² Terminal block 1in/1out-grey-10 mm² Terminal block 1in/1out-blue-16 mm² Terminal block 1in/1out-grey-16 mm² Blue end plate - 4 mm² Grey end plate - 4 mm² Blue end plate - 4 mm² Grey end plate - 4 mm² Blue end plate - 6 mm² Grey end plate - 6 mm² Blue end plate - 10 mm² Grey end plate - 10 mm² Blue end plate - 16 mm² Grey end plate - 16 mm² 2-pole insulated commoning link - 6 mm² Terminal block 1in/1out-green/yellow-4 mm² Terminal block 1in/2out-green/yellow-4 mm² Terminal block 1in/1out-green/yellow-6 mm² Terminal block 1in/1out-green/yellow-10 mm² Terminal block 1in/1out-green/yellow-16 mm² Separation partition - 4 mm² Separation partition - 4 mm² Separation partition - 6 mm² Separation partition - 10 mm² Separation partition - 16 mm² Label for markers Screw terminal block grey 35 mm² Screw terminal block blue 35 mm² Screw terminal block grey 70 mm² Screw terminal block blue 70 mm² Screw terminal block grey 150 mm² Screw terminal block blue 150 mm² 87 87 87 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 86 EZ4TSHD3P EZ4TSHD4P EZATSHD3P EZATSHD4P EZETSHD3P EZETSHD3PN EZETSHD4P EZETSHD4PN Long terminal shield EZC/EZCV250 3P Long terminal shield EZC/EZCV250 4P Long terminal shield EZC100-3P Long terminal shield EZC100-4P Long terminal shield EZC250-3P Long terminal shield EZC250-3P Long terminal shield EZC250-4P Long terminal shield EZC250-4P 36, 37 36, 37 37 37 36 37 36 37 LV429285 LV429306 LV429307 LV429369 32, 33, 35 32 32 40 LV429515 LV429516 LV429517 LV429518 LV432593 LV432594 Sas Vigi NSX 100/250 400/630 Adaptator NSX 100/250 3P Adaptator NSX 100/250 4P Mechanical interlocking for NSX 100/250 changeover system Short terminal shield NSX400/630 3P Short terminal shield NSX400/630 4P Long terminal shield NSX100/250 3P Long terminal shield NSX100/250 4P Long terminal shield NSX400/630 3P Long terminal shield NSX400/630 4P PRA90045 PRA90046 PRA90047 PRA90048 PRA90049 PRA90050 PRA90051 50 mm² terminal block kit 25 mm² terminal block kit 4 x 6 mm² terminal block kit Splitter block kit Splitter block kit Splitter block kit Terminal block support kit 83 83 83 83 83 83 83 EZ LV PRA 32, 33, 35 32, 33, 35 32, 33, 40 32, 33, 40 35 35 9 Presentation Overview To respond to increasing building requirements Improve the continuity of service 10 Ensure the safety of life and property Control deadlines and costs Prisma Plus: the optimised, tested and IEC compliant solution, for low voltage electrical distribution and control switchboards. Prisma Plus, a comprehensive range of enclosures and cubicles > A solution based on more than 25 years of experience in low voltage switchboards. > Integrating Schneider Electric switchgear offerings and ensuring electrical, mechanical and communication functions complete consistency. > Quality production, certified ISO 9001. 11 Presentation Overview G System > Small companies > Buildings > Offices 160 A > Schools > Hotels, etc. 12 Pack > Residential > Laboratories > Healthcare centres > Shopping centres > Supermarkets > Malls, etc. P System 3200 A > Hospitals > Bottling factories > Packaging Packaging factories 630 A > Automobile factories > Food industry > Deary > Internet data centres Prisma Plus P > Logistics centres, etc. Prisma Plus G 13 Presentation Overview Simple, functional systems for safe, up to 630 A Switchboards that are safe… With Prisma Plus G you can be sure to build 100 % Schneider Electric switchboards that are safe, optimised: > All components (switchgear, distribution blocks, prefabricated connections, etc.) are perfectly rated and coordinated to work together; > All switchboard configurations, even the most demanding ones, have been tested. You can prove that your switchboard meets the current standards, at any time. You can be sure to build a reliable electrical installation and give your customers full satisfaction in terms of dependability and safety for people and the installation. …aesthetics Prisma Plus G with its discreet design, blends harmoniously into all tertiary and industrial buildings, including in entrance halls and passageways. Available power Safety of people and property Controlled costs and delivery times Upgradeability 14 upgradeable LV switchboards …optimised and upgradeable With Prisma Plus G you can build just the right switchboard for your customer, sized precisely to fit costs and needs. With this complete, prefabricated and tested system, it's easy to upgrade your installation and still maintain the performance levels. > The wall-mounted and floor-standing enclosures combine easily with switchboards already in service. > Devices can be replaced or added at any time. Simple moves for cabling in the workshop Efficient installation and connection work on site Easy maintenance throughout the switchboard All connection points are fully accessible and easy to check. Easy connection on site, whatever the cable cross-section or installation location. Easy and direct access to devices, in a switchboard in service. 15 Presentation IEC 61439 standard The switchboard, central to the electrical installation Both the point of arrival of energy and a device for distribution to the site applications, the LV switchboard is the intelligence of the system, central to the electrical installation. It plays an essential role in the availability of electric power, while meeting the needs of personal and property safety. Its definition, design and installation are based on precise rules; there is no place for improvisation. The IEC 61439 standard aims to better define "low-voltage switchgear and controlgear assemblies", ensuring that the specified performances are reached. It specifies in particular: > the responsibilities of each player, distinguishing those of the original equipment manufacturer; the organization that performed the original design and associated verification of an assembly in accordance with the standard, and of the assembly manufacturer - the organization taking responsibility for the finished assembly; > the design and verification rules, constituting a benchmark for product certification. All the component parts of the electrical switchboard are concerned by the IEC 61439 standard. Equipment produced in accordance with the requirements of this switchboard standard ensures the safety and reliability of the installation. A switchboard must comply with the equirements of standard IEC 61439-1 and 2 to guarantee the safety and reliability of the installation. Managers of installations, fully aware of the professional and legal liabilities weighing on their company and on themselves, demand a high level of safety for the electrical installation. What is more, the serious economic consequences of prolonged halts in production mean that the electrical switchboard must provide excellent continuity of service, whatever the operating conditions. The Schneider Electric solution > Specify switchboards that comply with standard IEC 61439-1 and 2. > guarantee a level of safety that has been 100 % tested, from the day the switchboard is installed and throughout its service life. > ensure a lasting investment through easy upgrading of the installation in compliance with the standard. > guarantee that the switchboard complies with the technical specifications. 16 Prisma Plus tested switchboards The conformity of the switchboard has been tested and proven. A Prisma Plus switchboard is: > made up of Schneider Electric low-voltage devices and components that all comply with the applicable standards; > based on configurations in our catalogue; > made up of Prisma Plus mechanical and electrical components that have been subjected to the verification of original equipment manufacturer; > mounted and wired by a panelbuilder in compliance with professional standards; > subjected to the individual verification. Schneider Electric makes available to the panelbuilder everything required to create tested Prisma Plus switchboards, including the basic configurations in the low voltage distribution catalogue, all the documentation for switchboard design and mounting, calculation and design software, etc. Panelbuilders can demonstrate conformity with standard IEC 61439-1 and 2 by presenting the declarations or certificates of conformity for type tests carried out by independent laboratories (ASEFA, ASTA, KEMA, etc.) and supplied by Schneider Electric. The panelbuilder is responsible for the individual routine verification and delivers the corresponding declarations of conformity. Original Manufacturer and Assembly Manufacturer: Both involved in tested assemblies Standard IEC 61439 clearly defines the type of verifications that must be conducted by both organisations involved in final conformity of the solution: the Original Manufacturer, guaranteeing assembly system design and the Assembly Manufacturer, responsible for the final conformity of the switchboard. Proje ct spe cifica tion* Specifier sse ly mb A Original Manufacturer The organisation that has carried out the original design and the associated verification of an assembly system. He is responsible for the "Design verifications" listed by IEC 61439-2 including many electrical tests. Sy m ste Tes t Assembly Manufacturer (Panel builder) ed As > Specifies the needs and constraints for design, installation, operation and upgrading of the complete system. > Checks that its requirements have been fully integrated by the Assembly Manufacturer. Depending on the application, the specifier could be the end-user or a design office. sem bly The organisation (whether or not the same as the OM) responsible for the completed assembly. He is responsible for "Routine verifications" on each panel produced, according to the standard. If he derivates from the instructions of the original manufacturer he has to carry out again design verifications. End-User Should ask for a certified LV switchboard. By systematically requesting routine verifications, he ensures that the assembly system used is compliant. * Schneider Electric has developed a specification guide. 17 Presentation IEC 61439 standard The main 10 functions of standard IEC 61439 For each of the following 10 functions, the standard IEC 61439 requires design verifications from the system manufacturer - mainly through type-tests - and routine verifications on each panel from the Panel Builder to achieve 3 basic goals: safety, continuity of service and compliance with end-user requirements. Safety Voltage stresses withstand capability To withstand long term voltages, and transient and temporary overvoltages according to the insulation coordination principles and requirements. Current-carrying capability To protect against burns and to withstand temperature rise: > when any circuit is continuously loaded, alone, to the specified current > when the assembly is loaded to the specified current according to the specified load pattern (between circuits and/or as a function of the time). Short-circuit withstand capability To withstand the stresses resulting from the prospective short-circuit current and from the associated data (High forces between conductors, temp. rise in a very short time, air ionization, overpressure). Protection against electric shock > Hazardous-live-parts not to be accessible (basic protection) > Accessible conductive parts not to become hazardous-live (fault protection). Protection against risk of fire or explosion > Resistance to internal glowing elements > Note: Protection of persons, and optional protection of the assembly, against arcing due to internal fault can be specified through a "special test" according to IEC 61641. Continuity of service Maintenance and modification capability Capability to preserve continuity of supply without impairing safety during assembly maintenance or modification > Electrical condition of the assembly or various circuits > Speed of exchange of the functional units > Test facilities… Electro-Magnetic compatibility To properly function (immunity) and not to generate EM disturbances (emission) in specified environmental conditions: > Industrial networks or locations (Environment A) > Domestic, commercial, and light industrial locations (Environment B). Compliance with end-user requirements Capability to operate the electrical installation To properly function, according to: > The electrical diagram of the overall system and related information (voltages, coordination…) > The specified operating facilities (e.g. free or restricted access to Man Machine Interfaces, isolation of the outgoing circuits…). Capability to be installed on site > To withstand handling, transport, storage… and installation constraints > Capability to be erected and connected (type of enclosure, type, material and cross sectional areas of external conductors). Protection of the assembly against mechanical and atmospheric environmental conditions > Presence of water or solid foreign bodies (IP according to IEC 60529) > External mechanical impacts (optional IK according to IEC 62262) > Indoor or outdoor installation (humidity, UV). 18 IEC 61 439-1 paragraph 11.4 Protection against electric shocks and integrity of protection circuits The following should be checked visually: > Presence of protective shields against direct and indirect contacts on live parts; > Presence of the PE conductor. The continuity of protection circuits is ensured by compliance with the assembly instructions delivered with each product. Standard individual check sheet in accordance with the IEC 61439-1 and 2 standard from the assembly manufacturer (panelbuilder) IEC 61 439-1 paragraph 11.5 Integration of incorporated components The assembly manufacturer must comply with the instructions of the original equipment manufacturer for installation and wiring of the components used. Job No.: ................................................................................................. Switchboard No.: ................................................................................... Drawing No./Rev. No.: ............................................................................ Chapter IEC 61 439-1 paragraph 11.6 Degrees of protection provided by enclosures 11.2 Internal electric circuits and connections Insulation clearances and creepage distances 11.3 Protection against electric shocks and integrity of protection circuits 11.4 Integration of incorporated components 11.5 This allows: > not only self-checking to check effective tightening to torque; > but also identification of any loosening. Internal electric circuits and connections 11.6 Terminals for external conductors 11.7 Mechanical operation 11.8 IEC 61 439-1 paragraphe 11.9 Dielectric properties 11.9 Dielectric properties Wiring, operating performance and function 11.10 The main circuits, and the auxiliary and control circuits connected to the main circuit, shall be subjected to the test voltage in accordance. Date of verification: Schneider Electric recommends marking the nut with a tinted acrylic lacquer, indelible and temperature-resistant. Verified ............ / ............ /............. IEC 61 439-1 paragraph 11.10 Wiring, operating performance and function Verification of wiring and marking conformity with the drawings, parts list and diagram. Verifications performed by: ..........................................................................………………………… 19 Incomer Compact NSX250 4P Fixed, front connection Toggle Incoming cables via bottom to incoming connection block Examples of switchboard configurations PD390891_SE Presentation Distribution Polybloc distribution block Outgoing devices Multi 9 or Acti 9 devices Supply 80 A Multiclip Comb busbars Cable running Straps + cover Connection Terminal block at top of switchboard Motor circuit breakers Supply Comb busbars Cable running Straps + cover Connection Terminal block at top of switchboard IP30 enclosure PD390287_SE Wall-mounted enclosure, W = 595 mm, H = 930 mm Plain door Partial plain door 20 Incomer Interpact INS160 4P Incoming cables via top Examples of switchboard configurations PD390446R_SE Presentation Distribution 160 A Powerclip busbars Outgoing devices Multi 9 or Acti 9 devices Supply 80 A Multiclip Comb busbars Cable running Straps + cover Connection Terminal block in duct, W = 300 mm Motor circuit breaker + contactor combinations Supply Cable wiring Cable running Straps + cover Connection Terminal block in duct, W = 300 mm IP30 enclosure PD395007_SE Wall-mounted enclosure, W = 595 mm, H = 1230 mm Transparent door Duct, W = 305 mm, H = 1230 mm Plain door 21 Incomer Compact NSX250 Fixed, front connection Toggle Incoming cables via top to incoming connection block Examples of switchboard configurations PD390288_SE Presentation Distribution Powerclip busbars Outgoing devices Multi 9 or Acti 9 devices Supply 80/200 A Multiclip Comb busbars Cable running Straps + cover Trunking Connection Terminal block in duct, W = 300 mm Motor circuit breakers Supply Cable wiring Cable running Trunking Connection Terminal block in duct, W = 300 mm IP30 enclosure PD390289_SE Wall-mounted enclosure, Transparent door W = 595 mm, H = 1230 mm Duct, W = 305 mm, Plain door H = 1230 mm 22 Incomer Interpact INS160 Lateral handle Incoming cables via bottom, directly to device Examples of switchboard configurations PD390450R_SE Presentation Distribution Distribloc distribution block Outgoing devices Multi 9 or Acti 9 devices Supply Comb busbars Cable running Cable running Straps + cover Connection Terminal block at bottom of enclosure Motor control and protection devices Supply Comb busbars Cable running Trunking Connection Terminal block at bottom of enclosure IP55 enclosure PB110003 Wall-mounted enclosure, Transparent door W = 595 mm, H = 1250 mm 23 Presentation Incomer Compact NSX400 Fixed, front connection Toggle Incoming cables via bottom in duct (W = 300 mm) to incoming connection block PD395034_SE Examples of switchboard configurations Distribution Powerclip busbars Outgoing devices Compact NSX250 Fixed, front connection Toggle Supply Powerclip busbars with power supply block Multi 9 or Acti 9 devices Supply Comb busbars 200 A Multiclip Cable running Trunking Connection Vertical terminal block at bottom of floor-standing enclosure Appareils protection et commande moteur Supply Multiclip 200 A Cable running Trunking Connection Vertical terminal block at bottom of floor-standing enclosure Enveloppe IP30 PD390893_SE Floor-standing enclosure, Transparent door W = 595 mm, H = 1830 mm Duct, W = 305 mm, Plain door H = 1830 mm 24 Presentation Determining catalogue numbers Rapsody software Easy design with Rapsody software A time-saver in the design and quotation phases. More flexibility since modifications and upgrades are possible throughout the project. 5 easy steps to design a switchboard Define the switchboard's electrical and environmental characteristics, in a few clicks. Choose and configure the devices to be installed, with no risk of error. Customise, and easily modify the single-line diagram. Move or duplicate devices. Generate current distribution and connection systems. Choose the switchboard and let the software set up the enclosure. A list of mounting and connection accessories is proposed to make mounting work easier. Automatically export the information required to make a clear, comprehensive and professional quotation. 25 Determining catalogue numbers Starting with the electrical diagram: IP30 switchboard DD384078 Presentation NSX250 Installation/connection Distribution using Powerclip busbars Multi 9 or Acti 9 > see page 47 C60 ou IC60 NSX100/250 NSX NSX 03232 NSX All Multi 9 or Acti 9 devices Multi 9 or Acti 9 devices y 40 A DD384085 DD383519 Order the mounting plates and front plates taking into account: b supply to the rows b cable running. 1 DD383518 Install the modular devices All Multi 9 or Acti 9 devices 2 TeSys "U" > see page 49 DD381978 Multi 9 or Acti 9 devices y 40 A DD381880 b Multiclip distribution block > see page 80 b cable running > see page 60 Determine the size of the switchboard b count the number of occupied modules 19 modules b determine the corresponding wall-mount enclosure 21 modules b order the additional plain front plate. 26 Plain front plate > see page 56 DD381979 DD383521 DD381878 2 NSX100/250 DD383961 b order the mounting plates and the front plates b the incoming connection block b the power supply block for the Powerclip busbars. 1 DD384084 DD381888 > see page 32 DD383850 Install the incomer C60 ou IC60 DD383960 C60 ou IC60 Powerclip busbars > see page 68 IP wall-mount enclosure 2 Duct, W = 300 mm DD381983 3 Cable tie supports 4 Accessories for lifting, handling, wall mounting, finishing parts, etc. DD381884 1 DD381885 DD381892 > see page 89 DD381985 Select the enclosures DD381982 DD383523 > see page 84 DD383520 Select the terminal blocks and the earth bar DD384356 DD381882 DD383522 Plan the distribution system DD384355 Determining catalogue numbers Presentation Wall-mount enclosure (IP30) 27 Functional system 28 Functional system Contents Presentation .................................................................................30 Functional units and distribution...........................32 Circuit breakers ............................................................................32 Compact NSX 100/250 horizontal mounting ....................................................... 32 Compact NSX 100/250 vertical mounting ........................................................... 33 Compact NSX 400/630 horizontal mounting ....................................................... 34 Compact NSX 400/630 vertical mounting ........................................................... 35 Easypact EZC100/400 horizontal mounting........................................................ 36 Easypact EZC100/400 vertical mounting ............................................................ 37 Switch-disconnectors ...................................................................38 Interpact INS-INV250/630 horizontal mounting................................................... 38 Interpact INS-INV250/630 vertical mounting....................................................... 39 Manual source changeover system ..............................................40 Compact NSX 100/250 changeover system ....................................................... 40 Interpact INS-INV250 changeover system.......................................................... 41 Fusegear ......................................................................................42 Fupact INF horizontal mounting .......................................................................... 42 Fupact INF vertical mounting .............................................................................. 43 Fupact ISFT and ISFT-N horizontal mounting ..................................................... 44 Fupact ISFT and ISFT-N vertical mounting ......................................................... 45 Modular devices............................................................................46 Modular devices 80/160 A switchboard incomer ................................................. 46 Modular devices outgoers y 63 A......................................................................... 47 Industrial control devices ..............................................................48 TeSys, Altistart, Phaseo ...................................................................................... 48 Other devices................................................................................50 Kilowatt-hour meters Classe II ............................................................................ 50 Kilowatt-hour meters ........................................................................................... 51 Human-switchboard interface ............................................................................. 52 Accessories ................................................................. 56 Front plates, rails, slotted mounting plates .......................................................... 56 Fixing accessories .............................................................................................. 58 Partitioning.......................................................................................................... 59 Cable running...................................................................................................... 60 Switchboard lighting............................................................................................ 62 Finishing parts..................................................................................................... 63 Management of the internal temperature ............................................................ 64 Distribution ................................................................. 66 Panorama of the solution .................................................................................... 66 Non-Centralised distribution .........................................................68 630 A insulated busbar........................................................................................ 68 400 A rear busbars .............................................................................................. 70 630 A multi-stage busbars in duct........................................................................ 72 Insulated flexible bars ......................................................................................... 74 Centralised distribution .................................................................75 Distribution block ................................................................................................ 75 Comb busbars..................................................................................................... 82 Earth block / neutral block ................................................................................... 83 Earth bars ........................................................................................................... 84 Terminal blocks ................................................................................................... 86 Terminal blocks layout......................................................................................... 87 29 Functional system Presentation Readily available close by Straightforward organisation to make your job easier The kit concept makes handling and transport easier and you get to benefit from Schneider Electric’s efficient international logistics.Your distributor, hand-picked by Schneider Electric, can give you the very best advice. For determining catalogue numbers, > see page 25. > Clearly identified functions. The switchboard is set up in different functional units, organised naturally. Compact NSX 160 Mounting plate Terminal block Busbar power connection Front plate Example: "Incomer" functional unit. > A switchboard with a high degree of legibility. The easy-to-read switchboard circuit diagram makes on-site cabling and connection operations simple. 30 Functional system Presentation The Prisma Plus functional system The Prisma Plus functional system can be used for all types of low-voltage distribution switchboards up to 630 A, in commercial and industrial environments. Switchboard design is very simple. A functional structure for devices made up of wall-mounted and floor-standing enclosures that can be used alone or combined. A distribution system made up of Centralised distribution blocks and vertical busbars installed on the side or in the rear of the switchboard. Complete functional units Each device is part of a functional unit comprising: b a dedicated mounting plate for device installation b a front plate to block direct access to live parts b prefabricated busbar connections b systems for on-site connections and running of auxiliary wires. The functional units are modular and are arranged rationally, one on top of another, within the enclosure. The system includes everything required for functional unit mounting, supply and onsiteconnection. The components of the Prisma Plus system and those of the functional units in particular have been designed and tested taking into account device characteristics. This design approach ensures a high degree of reliability in system operation and optimum safety for personnel. Electrical characteristics Prisma Plus components comply with standard IEC 61439-1 et 2 and have the following electrical characteristics: b rated insulation level of main busbars at rear of enclosure: 1000 V b rated operational current Ie (40 °C): 630 A b rated peak withstand current Ipk: 53 k b rated short-time withstand current Icw: 25 kA rms / 1 second b frequency: 50/60 Hz. 31 Functional system Compact NSX 100/250 horizontal mounting Functional units and distribution Circuit breakers 300 600 Devices DD380594 Horizontal fixed (1) DD383856 Mounting Toggle Number of devices per row No. of vertical modules Mounting plates Front plates with cut-out [No. of vertical upstream modules] downstream Incoming connection block Long terminal shields + cable tying Direct rotary handle NSX100/250 1 5 03030 03232 [4] 03801 [1] cables via top: 04066 cables via bottom: 04067 - Vigi NSX100/250 NSX100/250 Motor mechanism module Vigi NSX100/250 NSX100/250 1 6 03033 03292 [4] 03802 [2] - 1 8 03031 03232 [4] 03802 [2] 03802 [2] - 1 8 03031 03292 [4] + LV429285 (sas) 03802 [2] 03802 [2] - 1 8 03032 03234 [4] 03802 [2] 03802 [2] - 3P: LV429517 4P: LV429518 08867 3P: LV429517 4P: LV429518 - 3P: LV429517 4P: LV429518 3P: LV429517 4P: LV429518 (1) Maximum size of connection cables: 70 mm². For cable cross-sections greater than 70 mm², use of a cable duct is recommended. Devices Toggle Direct rotary handle + adaptator NSX100/250 Vigi NSX100/250 NSX100/250 NSX100/250 1 4 03030 03232 [4] 1 4 03033 03292 [4] 1 6 03031 03232 [4] 1 6 03032 03234 [4] 1 4 03032 03290 [4] 3P: LV429517 4P: LV429518 - - 03802 [2] 03802 [2] 3P: LV429517 4P: LV429518 3P: LV429306 4P: LV429307 Powerclip busbars All type Busbars / distribution blocks Power supply block Short terminal shield 3P: 04033 > see page 75 > see page 68 4P: 04034 04060 (2) 04060 (2) 3P: LV429515 4P: LV429516 Rear busbars DD380777 Type of connected devices 1 6 03031 03292 [4] + LV429285 (sas) 03802 [2] DD380522 Polybloc distribution block DD380587 Distribution Toggle NSX (2) Supplied with connections - (3) Connection must be made. 32 Toggle NSX100/250 NSX100/250 with ammeter module or Vigi Number of devices per row No. of vertical modules Mounting plates Front plates with cut-out [No. of vertical modules] downstream Long terminal shields Motor mechanism module NSX with ammeter module or Vigi NSX Direct rotary handle or All type motor mechanism module > see page 70 04061 (3) - Busbars in duct DD380761 300 DD383855 Horizontal plug-in DD380589 600 Horizontal fixed DD383855 Mounting All type > see page 72 Functional system Compact NSX 100/250 vertical mounting Functional units and distribution Circuit breakers Vertical fixed 300 600 Devices DD380666 DD383871 Mounting Toggle Number of devices per row No. of vertical modules (1) Mounting plates Front plates with cut-out [No. of vertical modules] upstream downstream Incoming connection block Divisible 85 x 147 mm blanking plates 107 x 147 mm Direct rotary handle NSX100/160 NSX250 4 x 3P or 3 x 4P 7 9 03040 03040 03243 [5] 03243 [5] Vigi NSX100/160 Vigi NSX250 NSX100/160 NSX250 8 03040 03241 [7] 11 03040 03241 [7] Vigi NSX100/160 Vigi NSX250 4 x 3P or 3 x 4P 7 9 8 03041 03041 03041 03243 [5] 03243 [5] 03244 [7] + LV429285 (sas) 03802 [2] 03802 [2] 03802 [2] 03801 [1] 11 03041 03244 [7] + LV429285 (sas) 03802 [2] 03802 [2] 03802 [2] 03802 [2] 03802 [2] 03802 [2] 03801 [1] 03802 [2] 3P: LV429517 4P: LV429518 03249 (to add modular devices to a row with Compact NSX 3P or 4P without electronic trip unit) 03222 (to add modular devices to a row with Compact NSX 3P or 4P with electronic trip unit) Devices Number of devices per row No. of vertical modules (2) Mounting plates Cut-out front plates Incoming connection block NSX 100/250 DD380777 DD380761 Direct rotary handle Vigi NSX NSX 100/250 100/250 1 1 1 9 11 9 03050 03050 03253 03293 3P: LV429517 4P: LV429518 (2) With or without spreaders. Vigi NSX 04061 04062 3P: LV429515 4P: LV429516 must be made Distribution Polybloc distribution block in duct Vertical fixed Toggle NSX > see page 68 03051 03253 Type of connected devices Distribution block / busbars Adjustable rail Power supply block Connection block Short terminal shield All type > see page 70 Busbars Powerclip (3) All type NSX 3P: 04033 4P: 04034 All type > see page 72 Multi-stage busbars Rear busbars or multi-stage distribution block in duct DD380777 600 > see page 75 DD382305 300 All type 3P: 04033 4P: 04034 03002 - DD383858 Mounting Busbars in duct DD382567 Adjustable rail Power supply block Connection block Short terminal shield Rear busbars DD380745 Type of connected devices Distribution block / busbars Polybloc distribution block Powerclip busbars DD380593 Distribution DD380780 (1) With or without spreaders, whatever the distribution solution. All type All type > see page 68 > see page 72 > see page 70 03011 - 04061 - - 04062 04065 Vigi NSX > see page 75 - must be made 3P: LV429515 4P: LV429516 - (3) Space available at the top of the enclosure after mounting the universal power supply block: - NSX 100/250 = 7 modules - Vigi NSX 100/250 = 9 modules. Space required by power supply block on Powerclip busbars = 5 modules. 33 Functional system Compact NSX 400/630 horizontal mounting Functional units and distribution Circuit breakers Devices Number of devices per row No. of vertical modules Mounting plates Front plates cut-out [No. of vertical upstream modules] Incoming connection block DD383851 NSX400/630 1 9 03070 03296 [6] 03803 [3] 1 6 03070 03296 [6] - 04076 04076 Powerclip busbars Rear busbars DD380783 Distribution Toggle Type of connected devices Busbars Power supply block 34 NSX400 NSX630 04070 04071 > see page 68 Busbars in duct All type DD380761 300 DD380777 600 Horizontal fixed DD383852 Mounting All type > see page 70 > see page 72 - - Functional system Compact NSX 400/630 vertical mounting Functional units and distribution Circuit breakers 300 600 Devices DD383854 Vertical fixed DD383853 Mounting Toggle Direct rotary handle NSX400 Number of devices per row No. of vertical modules (1) Mounting plates Front plates cut-out [No. of vertical modules] upstream downstream Long terminal shield NSX630 Vigi NSX400 Vigi NSX630 NSX400/630 1 11 03073 03275 [9] 1 12 03073 03275 [9] 1 13 03073 03297 [11] 1 14 03073 03297 [11] 1 14 03074 03275 [9] 03802 [2] 3P: LV432593 4P: LV432594 03802 [2] 03801 [1] 03802 [2] - 03802 [2] 03801 [1] 03802 [2] 03803 [3] Vigi NSX400/630 1 17 03074 03297 [11] + LV429285 (sas) 03802 [2] 03804 [4] (1) With or without spreaders. All type All type > see page 68 > see page 70 Busbars in duct DD380761 Type of connected devices Busbars Power supply block Short terminal shield Rear busbars DD380777 Powerclip busbars DD383825 Distribution All type > see page 72 04074 (2) 3P: LV429515 4P: LV429516 Devices Number of devices per row No. of vertical modules (3) Mounting plates Front cut-out plates [No. of upstream vertical downstream modules] Long terminal shield Toggle Direct rotary handle NSX400 NSX630 Vigi NSX400/630 NSX 400/630 1 1 1 11 03080 03298 [8] 12 03080 03298 [8] 03812 [2] 03811 [1] 03812 [2] 03812 [2] 14 03080 03299 [10] 03812 [2] 03812 [2] 1 03081 03283 [12] - Rear DD380777 Type of connected devices Busbars Power supply block Connection block Short terminal shield Barrier Powerclip (4) Multi-space in duct Dd382305 600 DD383858 300 Busbars Vertical fixed DD383857 Mounting Dd382567 (2) Connection must be made All type All type All type > see page 68 > see page 70 > see page 72 04074 - - 04073 04075 - 3P: LV432591 4P: LV432592 included 04197 04198 (4) Space available at the top of the enclosure after mounting the universal power supply block: - NSX 100/250 = 7 modules - Vigi NSX 100/250 = 9 modules Space required by power supply block on Powerclip busbars = 5 modules. 3P: LV432593 4P: LV432594 (3) With or without spreaders 35 Functional system Functional units and distribution Easypact EZC100/400 horizontal mounting Circuit breakers 600 300 Devices Horizontal fixed DD383994 Mounting Toggle EZC250 / EZCV250 Distribution Rear busbars Busbars in duct Type of connected devices Busbars / distribution block All type 36 > see page 70 DD380761 4P 1 4 03104 03304 EZETSHD4P DD380777 Number of devices per row No. of vertical modules Mounting plates Cut-out front plates Long terminal shield (set of 2) 3P 1 4 03104 03304 EZETSHD3P All type > see page 72 EZC400 3P 1 5 03105 03306 EZ4TSHD3P 4P 1 5 03105 03306 EZ4TSHD4P Functional system Functional units and distribution Easypact EZC100/400 vertical mounting Circuit breakers Devices Toggle EZC100 4P 3 5 03102 03303 EZATSHD4P EZC250 / EZCV250 3P 4 7 03104 03305 EZETSHD3PN - Distribution Polybloc distribution block Rear busbars DD380761 3P 5 5 03102 03303 EZATSHD3P DD380777 1P 15 5 03102 03303 03249 DD383493 Number of devices per row No. of vertical modules Mounting plates Cut-out front plates Long terminal shield (set of 2) Divisible blanking plate H = 85 mm, L = 147 mm DD383993 300 DD383044 600 Vertical fixed DD38110 Mounting Type of connected devices Busbars / distribution block Fixed rail EZC100 04031 (x no. of pole) 03001 > see page 70 All type All type 4P 3 7 03104 03305 EZETSHD4PN EZC400 3P 1 10 03105 03307 EZ4TSHD3P 4P 1 10 03105 03307 EZ4TSHD4P Busbars in duct > see page 72 37 Functional system Interpact INS-INV250/630 horizontal mounting Functional units and distribution Switch-disconnectors 300 Devices Direct front handle Number of devices per row No. of vertical modules Mounting plates Front plates cut-out [No. of vertical upstream modules] Incoming cables via top connection cables via top block Horizontal fixed, direct connection 300 Devices Direct front handle Distribution Polybloc distribution block Powerclip busbars Dd381346 Dd381349 Number of devices per row No. of vertical modules Mounting plates Front plates cut-out [No. of vertical upstream modules] Long terminal shield (set of 2) Type of connected devices INS-INV250 Distribution block / busbars Power supply block (1) 3P 04033 - INS-INV 250 (1) Supplied with connection 38 4P 04034 INS-INV 320/400 04070 INS-INV320/630 INS-INV320/630 1 4 03030 03231 [4] 1 9 03070 03271 [6] 1 6 03070 03271 [6] - 03803 [3] - 29324 32565 32565 Rear busbars INS-INV 500/630 > see page 68 04060 INS-INV250 04071 Busbars in duct DD380761 600 04066 04067 DD380670 Mounting INS-INV250 1 5 03030 03231 [4] 03801 [1] DD380777 600 Horizontal fixed with connection block DD380669 Mounting All type All type > see page 70 > see page 72 Functional system Interpact INS-INV250/630 vertical mounting Functional units and distribution Switch-disconnectors Vertical fixed with or without spreaders Dd380761 Mounting 300 Direct front handle Lateral handle INS/INV320/400 INS/INV500/630 1 8 03040 03248 [5] 03801 [1] 03802 [2] 29324 1 10 03073 03274 [10] 32565 Distribution Polybloc distribution block Type of connected devices INS-NV250 Distribution block / busbars Front handle 3P 4P 04033 04034 INS-INV 250 Adjustable modular device rail Power supply block Connection block Short terminal shield 03002 - 03002 INS/INV250 1 12 03073 03274 [10] 03802 [2] 32565 Powerclip busbars Lateral handle 3P 4P > see page 68 04033 04034 + 04037 (1) + 04037 (1) 03003 03003 04060 04062 29322 1 8 03032 03806 [6] 03802 [2] 29324 Rear busbars INS-INV 320/630 Busbars in duct DD380761 Number of devices per row No. of vertical modules Mounting plates Front plates cut-out [No. of vertical upstream modules] downstream Long terminal shield (set of 2) Dd381348 INS/INV250 Dd381347 Devices DD380777 600 All type All type > see page 70 > see page 72 04074 must be made 32563 Type of connected devices Devices Front direct rotary handle INS-INV INS-INV INS-INV 250 320/400 500/630 Number of devices per row No. of vertical modules Mounting plates Front plates cut-out [No. of downstream vertical modules] Long terminal shield (set of 2) 1 1 1 9 03050 03251 [9] - 10 03080 03281 [10] - 12 03080 03281 [10] 03812 [2] 29324 32565 32565 Distribution blocks / Busbars Adjustable modular device rail Power supply block Connection block Short terminal shield Barrier Powerclip busbars (2) Multi-stage busbars in a duct INS-INV 250 INS-INV INS-INV INS-INV INS-INV All type 250 320/630 250 320/630 3P 04033 4P 04034 Rear busbars DD380777 Polybloc distribution block DD382571 600 Distribution DD382570 300 Vertical fixed with or without spreaders DD80773 Mounting DD382569 (1) Copper spacer. > see page 68 > see page 70 > see page 72 03011 - - - - 04061 04074 - - - 04064 04073 04065 04075 - - 29322 32563 29322 32563 - - included 04197 04198 (2) Space available at the top of the enclosure after mounting the universal power supply block: 7 modules. Encombrement du bloc d’alimentation sur Powerclip: 5 modules 39 Functional units and distribution Manual source changeover system Compact NSX 100/250 circuit breaker changeover system Mounting 600 300 Fixed (changeover with mechanical interlocking) DD380535 Functional system ON I reset O F OFF OF O Devices Front connection, direct rotary handle NSX100/250 No. of vertical modules Mounting plates Front plates cut-out [No. of vertical upstream modules] downstream Mechanical interlocking Long terminal shield Coupling accessory 40 3P 10 03043 03245 [5] 03802 [2] 03803 [3] LV429369 LV429517 29358 4P 10 03043 03245 [5] 03802 [2] 03803 [3] LV429369 LV429518 29359 Functional system Functional units and distribution Manual source changeover system 300 Fixed (Complete source changeover assembly) DD380537 600 Fixed (changeover with mechanical interlocking) DD380536 Mounting Interpact INS-INV250 switch-disconnector changeover system I ON I ON OFF O Devices Front, direct rotary handle INS-INV250 No. of vertical modules Mounting plates Front plates cut-out [No. of vertical upstream modules] downstream Mechanical interlocking Complete source changeover assembly Long terminal shield Coupling accessory Front, direct rotary handle 3P 9 03043 + 2 x 31064 (raiser) 03235 [5] 03802 [2] 03802 [2] 31073 - 4P 9 03043 + 2 x 31064 (raiser) 03235 [5] 03802 [2] 03802 [2] 31073 - 29324 29358 29324 29359 INS250 3P 9 03043 03247 [5] 03802 [2] 03802 [2] 100 A: 31140 160 A: 31144 200 A: 31142 250 A: 31146 29324 29358 4P 9 03043 03247 [5] 03802 [2] 03802 [2] 100 A: 31141 160 A: 31145 200 A: 31143 250 A: 31147 29324 29359 41 Functional system Fupact INF horizontal mounting Functional units and distribution Fusegear 300 Devices Extended rotary handle INF32 Number of devices per row No. of vertical modules Mounting plates Front plates cut-out [No. of vertical downstream modules] Long terminal shield Dd382475 600 Horizontal DD382474 Mounting INF40/60 INF100/160 3P or 4P 1 3 03113 03313 3P 1 5 03114 03314 4P 1 5 03114 03314 3P 1 7 03114 03314 [5] 4P 1 7 03114 03314 [5] - - - 03802 [2] (1) 03802 [2] (1) - 49658 49658 x 2 49659 x 6 49659 x 8 Multi-stage busbars in a duct DD381380 Type of connected devices All type Distribution blocks / busbars Additional 35 mm2 block Connection block > see page 70 INF100/160 3P must be made Powerclip busbars (2) > see page 68 04155 must be made 4P 04156 (2) The mounting plate for INF Fupact does not leave a passage for the busbar; it can only be installed below the plate. The distribution system is installed under the functional unit. 42 Rear busbars DD380777 Distribution DD383846 (1) Not needed if direct distribution. All type > see page 72 Functional system Fupact INF vertical mounting Functional units and distribution Fusegear 300 Devices Extended rotary handle INF32/40 Number of devices per row No. of vertical modules Mounting plates Front plates cut-out [No. of vertical downstream modules] Long terminal shield DD382478 600 Vertical DD382477 Mounting INF63 INF100/160 3P 4 3 03113 03312 4P 3 3 03113 03313 3P 3 5 03114 03314 4P 2 5 03114 03315 3P 2 7 03114 03315 [5] 4P 2 7 03114 03315 [5] - - - - 03802 [2] (1) 03802 [2] (1) - - 49658 49658 x 2 49659 x 6 49659 x 8 (1) Not needed if direct distribution. 4P 04031 x 4 03002 must be made DD380761 Distribution blocks / busbars Adjustable modular device rail Universal power supply block Connection block INF100/160 3P 04031 x 3 03002 must be made Busbars in duct DD380777 Type of connected devices Rear busbars DD381380 Polybloc distribution block Powerclip busbars (2) DD383658 Distribution INF100/160 All type All type > see page 70 > see page 68 > see page 72 04061 must be made (2) The mounting plate for INF Fupact does not leave a passage for the busbar; it can only be installed below the plate. The distribution system is installed under the functional unit. 43 Functional system Functional units and distribution Fupact ISFT and ISFT-N, 3P horizontal mounting Fusegear 600 300 Devices Number of devices per row No. of vertical modules Mounting plates Front plates cut-out [No. of vertical upstream modules] downstream Long terminal shield Horizontal DD342480 Mounting On mounting plate ISFT160 1 6 03121 03326 [3] 03801 [1] 03802 [2] (1) 49869 x 2 ISFT250 1 6 03124 03328 [5] 03801 [1] 49872 x 2 44 Powerclip busbars Rear busbars Dd380777 Type of connected devi ces Distribution blocks / busbars Universal power supply block Connection block All type All type > see page 68 04061 must be made > see page 70 Busbars in duct Dd380761 Busbars Dd382481 (1) Not needed if direct distribution. All type > see page 72 Functional system Fupact ISFT and ISFT-N, 3P vertical mounting Functional units and distribution Fusegear Dd382483 300 600 Vertical Dd382482 Mounting Number of devices per row No. of vertical modules Mounting plates Front cut-out plates upstream [No. of downstream vertical modules] Long terminal shield On mounting plate Comb busbar DD382484 Distribution Devices On busbars ISFT100 ISFT100N ISFT160 ISFT100N ISFT160 5 8 4 6 4 7 03120 03320 [6] 03801 [1] 8 03126 03325 [8] - 8 03121 03321 [6] 03802 [2] (1) 8 03122 03325 [8] - 8 03122 03321 [6] 03802 [2] (1) - - 49869 x 2 - 49869 x 2 Connected devices Comb busbar Type Number Coupler to connect 2 busbars Tooth cover Set of 3 connectors 25 to 95 mm2 ISFT100 2 3 4 5 49861 49862 49863 49861 + 49862 49890 49864 49865 DD382847 Polybloc distribution block Powerclip busbars Rear busbars Type of connected devices Connectors / distribution block / busbars Adjustable modular device rail Universal power supply block Connection block ISFT100 49860 All type 04031 x 3 All type must be made 03002 must be made 04061 must be made > see page 68 Busbars in duct DD380761 Connectors (2) DD380777 Distribution DD383659 (1) Not needed if direct distribution. All type All type > see page 70 > see page 72 (2) Set of 3 connectors 3 x 10 mm2 300 600 Devices Vertical fixed Dd382488 Mounting On mounting plate ISFT160 ISFT250 1 9 03125 03329 49872 x 2 Polybloc distribution block Powerclip busbars Type of connected devices Distribution block / busbars Adjustable modular device rail Universal power supply block Connection block ISFT160 04031 x 3 03011 must be made Multi-stage busbars in a duct Rear busbars DD380777 Distribution Dd382490 1 6 03123 03327 49869 x 2 Dd382843 Number of devices per row No. of vertical modules Mounting plates Cut-out front plates Long terminal shield All type All type All type 04061 must be made must be made > see page 68 > see page 70 > see page 72 45 Functional system Modular devices 80/160 A switchboard incomer Functional units and distribution Modular devices Devices No. of vertical modules Rail (48 modules of 9 mm) Modular front plates Blanking plate strip > see page 127 divisible Switch-disconnector Dd383995 300 600 Circuit breaker Dd383268 Mounting NG160, Vigi NG160 5 03002 (adjustable) (1) 03205 03220 03221 NG125, Vigi NG125, C120, Vigi C120, iC120, Vigi iC120 5 03001 03205 INS40/160 4 03001 03204 03220 03221 INS100/160 with long terminal shields 5 03001 03205 (1) Can be completed by a rail + raiser (ctn.no 04227) to instal modular devices on. 600 Devices No. of vertical modules Rail (20 modules of 9 mm) Front plates modular [No. of vertical modules] downstream Blanking plate strip > see page 127 divisible Switch-disconnector Dd383496 300 Circuit breaker Dd383626 Mounting NG160 5 03011 (adjustable) (2) 03214 [4] INS40/160 4 03010 03214 [4] INS100/160 with long terminal shields 5 03010 03214 [4] 03811 [1] 03220 03221 03220 03221 03811 [1] 03220 03221 (2) Can be completed by a rail + raiser (ctn.no 04227) to instal modular devices on. Multi-stage distribution DD382813 Distribloc distribution block DD383301 Polybloc distribution block 160 A DD383300 Busbars in duct DD380761 Rear busbars DD380777 Type of connected devices Distribution block / busbars Connection block Powerclip busbars Dd383270 Distribution All type All type All type All type All type All type must be made must be made > see page 68 > see page 68 > see page 70 > see page 72 > see page 75 > see page 75 > see page 77 > see page 77 Service connection 300 Devices Number of devices per row No. of vertical modules Rail (48 modules of 9 mm) Cut-out front plates Horizontal partitioning (3) Dd383531 600 Modular incoming fusegear Dd383530 Mounting Modular incoming fusegear 1 Ph 8 4 03001 03359 04331 Modular incoming fusegear 3 Ph 3 4 03001 03159 04331 (3) Order twice the catalogue number in case of other installation than at top enclosure 46 > see page 78 must be made Functional system Functional units and distribution Modular devices outgoers 63 A Modular devices Modular devices 40 A 48 4 (1) 03001 03204 03220 03221 48 3 03001 03203 03220 03221 Dd383121 Rail length (modules of 9 mm) No. of vertical modules Rail (48 modules of 9 mm) Modular front plates Blanking plate strip > see page 127 divisible All modular devices Vertical Dd383266 Devices Horizontal distances between centres: 150 mm Dd383265 300 600 Horizontal distances between centres: 200 mm Dd383264 Mounting 48 8 03001 x 3 03223 03220 03221 All modular devices 48 64 9 12 04226 04226 03228 03229 03220 03221 (1) Note: For a modular row with a 160A (half row) and 200 A Multiclip distribution block positioned directly below a non-modular mounting-plate (Compact, Interpact, etc...), or at the top of a switchboard, add one additional module (i.e. 4+1) and a plain upstream front plate(03801) Dd383489 Devices Rail length (modules of 9 mm) No. of vertical modules Rail (20 modules of 9 mm) Modular front plates Blanking plate strip > see page 127 divisible All modular devices 20 4 03010 03214 03220 03221 Modular devices 40 A 20 3 03010 03213 03220 03221 Distribution Comb busbar Multiclip distribution block DD384088 Horizontal distances between centres: 150 mm Dd383490 Horizontal distances between centres: 200 mm Dd382484 Distances between rows According devices All type 300 600 Type of connected devices Comb busbars / distribution blocks > see page 82 > see page 80 47 Functional system TeSys, Altistart, Phaseo Functional units and distribution Industrial control devices TeSys D, TeSys K contactors 300 Devices Useful length for rail No. of vertical modules Rail Plain front plates DD380708 600 For 600 mm wide wall-mounted For 300 mm wide duct and floor standing enclosures DD381613 Mounting LC1Dp or LC1Kp ( 40 A) 432 mm 3 03004 (in rear) 03803 LC1Dp or LC1Kp ( 40 A) 180 mm 3 03011 (adjustable) 03813 TeSys GV2/GV3 circuit breakers 300 Devices Useful length for rail No. of vertical modules Rail Front plates cut-out [No. of vertical upstream modules] downstream Blanking plate strip > see page 127 divisible TeSys GV2 432 mm 3 03001 03203 [3] 03220 03221 DD383492 600 For 600 mm wide wall-mounted For 300 mm wide duct and floor standing enclosures DD383494 Mounting TeSys GV3 432 mm 5 03002 03205 [5] 03220 03221 TeSys GV2 180 mm 3 03010 03213 [3] 03220 03221 TeSys GV3 180 mm 5 03011 (adjustable) 03213 [3] 03811 [1] 03811 [1] 03220 03221 Combined TeSys GV2 circuit breaker + contactor 300 Devices Useful length for rail No. of vertical modules Rail Front plates transparent [No. of vertical plain modules] downstream 48 For 300 mm wide duct DD381189 600 For 600 mm wide wall-mounted and floor standing enclosures DD381318 Mounting GV2 + LC1Dp or LC1Kp ( 40 A) 432 mm 5 03004 (in rear) 03342 [4] 03801 [1] GV2 + LC1Dp or LC1Kp ( 40 A) 180 mm 5 03011 (adjustable) 03352 [4] 03811 [1] Functional system TeSys, Altistart, Phaseo Functional units and distribution Industrial control devices Tesys U starter-controler 300 Devices Useful length for rail No. of vertical modules Rail Front plates transparent [No. of vertical plain modules] For 300 mm wide duct DD381190 600 For 600 mm wide wall-mounted and floor standing enclosures DD381319 Mounting TeSys U 432 mm 5 03004 (in rear) 03342 [4] (2) 03801 [1] TeSys U (1) 432 mm 4 03004 (in rear) 03342 [4] (3) - TeSys U 180 mm 5 03011 (adjustable) 03352 [4] (2) 03811 [1] TeSys U (1) 180 mm 4 03011 (adjustable) 03352 [4] (3) - (1) TeSys U without communication module, neither auxiliary contact, neither inverter module. (2) If the communication module is installed, the transparent front plate is mandatory. If not, the 2 front plates can be replaced by one plain front plate (cat.no 03805 in wall-mounted or floor-standing enclosure, 03815 in duct). (3) Or plain front plate (cat.no 03804 in wall-mounted or floor-standing enclosure, 03814 in duct). Soft starters Altistart 01 Number of devices per row Useful length No. of vertical modules Rail Slotted plates Plain front plates ATS01N103FT ATS01N109FT ATS01N222 ATS01N106FT ATS01N112FT to 232 ATS01N206 to 212 19 9 9 432 mm 432 mm 432 mm 4 5 6 03004 03003 03003 (in rear) 03804 03805 03806 DD381191 ATS01N230LY ATS01N272LY, ATS01N285LY ATS01N244LY ATS01N272Q, ATS01N285Q ATS01N244Q ATS01N103FT ATS01N106FT 2 432 mm 5 03003 2 420 mm 6 - 19 180 mm 4 03011 (adjustable) 03805 03172 03806 03814 Supply and LV/LV Phaseo transformer Mounting 600 300 Devices Useful length for mounting plate No. of vertical modules Slotted plates Plain front plates On recessed slotted mounting plate (L = 600 mm) On a slotted plate (L = 300 mm) DD380709 Devices DD382604 300 On recessed slotted On rail in duct mounting plate (L = 600 mm) (L = 300 mm) DD382816 600 On rail in the enclosure (L = 600 mm) DD382603 Mounting ABL6TS/TD, ABL6-RF 420 mm 4 03171 03804 ABL6TS/TD, ABL6-RF 172 mm 4 03175 03814 49 Functional system Kilowatt-hour meters Classe II Functional units and distribution Other devices Mounting 600 300 Devices Number of devices per row No. of vertical modules Mounting plates Front plate at transparent your choice plain Horizontal partitioning Insulating plates Accessories DD382949 Devices Number of devices per row No. of vertical modules Mounting plates Metering front plates Horizontal partitioning Insulating plate Accessories Single-phase (Ph + N) 3 6 03157 03155 04331 03154 M5 spacers for mounting plate > see page 58 3-phase (3 Ph + N) 2 9 03152 03158 04331 03154 Behind front plate (1) DD382951 300 DD382948 600 Accessible (1) DD382950 Mounting Single-phase (Ph + N) 3 6 03157 03343 03806 04331 03154 M5 spacers for mounting plate > see page 58 3-phase (3 Ph + N) 2 9 03152 03344 03807 04331 03154 (1) Order one additional horizontal partition in case of installation other than at the top of enclosure. Note: Meters can be installed directly on mounting plate equipped with 6 mm² earthing braid (cat.no 08910) and combined with partitioning or front plates. 50 Functional system Functional units and distribution Kilowatt-hour meters Other devices Devices Number of devices per row No. of vertical modules Mounting plates Front plates at transparent your choice plain Horizontal partitioning Earthing braid (2) Accessories Mounting 300 600 Devices Number of devices per row No. of vertical modules Mounting plates Front plates at transparent your choice plain Horizontal partitioning Earthing braid (2) Accessories 3-phase kilowatt-hour meters Connection blocks (3 Ph + N) 2 2 6 6 03160 03160 03343 03343 03806 03806 04331 04331 08910 08910 M5 spacers for mounting plate > see page 58 DD383047 DD383046 DD383045 300 600 Behind front plate (1) 3-phase kilowatt-hour meters (3 Ph + N) + connection block 1+1 6 03160 03343 03806 04331 08910 Behind front plate (1) DD382956 Mounting 3-phase (3 Ph + N) 1 9 03156 03354 03817 04332 08910 M5 spacers for mounting plate > see page 58 (1) Order one additional horizontal partition in case of installation other than at the top of enclosure. (2) Meters can be installed directly on mounting plate equipped with 6 mm² earthing braid (cat.no 08910) and combined with partitioning or front plates. 51 Functional system Functional units and distribution Human-switchboard interface Other devices 3 mounting types in Prisma Plus System G 2 types of device mounting 72x72 and 96x96 1 1 > In the device zone of wall-mounted and floor-standing enclosures Dd381705 Dd381685 > On an interface with plastic mounting plates clipped onto the metal front plate with cut-outs A 40 40 60 40 10 0 10 0 A 40 60 10 0 60 A 60 A 10 0 b The interface is made up of a metal front plate and plastic mounting plates that clip onto the front plate. b The devices are attached in the cut-outs of the plastic mounting plates and insulated from the front plate. Dd381687 2 > On a partial door with cut-outs in wall mounted and floor-standing enclosures Dd381643 Dd381688 Dd382574 b A system at the rear of the mounting plates guides the wires. 0 0 0 0 b Each mounting plate can receive an adhesive label. b Plain mounting plates are available to blank off any unused locations. b With flexible trunking to protect and guide wiring to door (04235). 3 2 > On a partial door with cut-outs, on an inclined visor by 30 ° Dd382636 Dd381689 > Directly on a metal front plate with cut-outs b Devices are attached directly to the metal front plate. b Blanking plates are available to blank off any unused locations. b With cut-out plastic mounting plate directly clipped on the visor. b Supplied with a drilling diagram for mounting on a plain door. Note: - to maintain the IP55 degree of protection, the measurement devices must be installed behind a transparent door. - if they are installed on a plain door, use the corresponding mounting plates. ( > see page 53). 52 Functional system Functional units and distribution Human-switchboard interface Other devices Vigirex and other devices 72 x 72 Measurement, inspection, indication DD382636 Other devices 72 x 72 6 3 03910 - Vigirex and other devices 72 x 72 5 03928 03902 03900 To blank-off or install: - from 1 to 4 buttons, ø 16 or 22 mm - 1 device 45 x 45 03907 To blank-off or install: - 1 or 2 buttons, ø 22 mm - 1 device 45 x 45 03900 To blank-off or install: - from 1 to 4 buttons ø 16 or 22 mm - 1 device 45 x 45 DD382575 Number of devices per row No. of vertical modules Visor Metal front plates with cut-outs Plastic mounting plates with cut-outs Blanking plate or device support Vigirex (1) and other devices 72 x 72 5 3 03904 03902 DD382575 Devices DD381689 300 Directly on a metal front plate On an inclined visor by 30 ° with cut-outs with plastic mounting plates DD383637 600 On an interface with plastic mounting plates DD381705 Mounting (1) RHU, RH10P, RH21P, RH99 relay, RM12T Multiplexer, for 72 x 72 mm version. Power Meter and other devices 96 x 96 Measurement, inspection, indication Number of devices per row No. of vertical modules Metal front plates with cut-outs Visor Plastic mounting plates with cut-outs Blanking plate or device support Other devices 96 x 96 Dd382636 DD383662 Dd381711 On an inclined visor by 30 ° with plastic mounting plates 4 3 03904 03903 Power Meter (2) and other devices 96 x 96 4 1 3 3 03911 03913 - Power Meter (2) and other devices 96 x 96 4 03928 03903 03901 To blank-off or install: - from 1 to 4 buttons ø 16 or 22 mm - 1 device 45 x 45 - 1 device 72 x 72 03908 To blank-off or install: - 1 or 2 buttons ø 22 mm - 1 device 45 x 45 - 1 device 72 x 72 03901 To blank-off or install: - from 1 to 4 buttons ø 16 or 22 mm - 1 device 45 x 45 - 1 device 72 x 72 DD382633 Devices Directly on a metal front plate with cut-outs DD383634 300 Dd382632 600 On an interface with plastic mounting plates DD382633 Mounting (2) Power Meter PM200 / PM700 / PM800, FDM121. 53 Functional system Functional units and distribution Human-switchboard interface Other devices Device 144 x 144 + 4 devices 72 x 72 Measurement, inspection, indication 600 300 Device 144 x 144 + devices 72 x 72 1+4 4 03912 03907 To blank-off the unused locations 72 x 72 or install: - 1 or 2 buttons ø 22 mm - 1 device 45 x 45 Dd382637 Devices Number of devices per row No. of vertical modules Metal front plates with cut-outs Blanking plate or device support On a metal front plate with cut-outs Dd381712 Mounting Vigilohm system 600 300 (1) Vigilohm TR22A/AH insulation monitor. 54 40 10 0 60 A Vigilohm system (1) + devices 72 x 72 1+6 4 03934 03907 To blank-off the unused locations 72 x 72 or install: - 1 or 2 buttons ø 22 mm - 1 device 45 x 45 Dd382637 Devices Number of devices per row No. of vertical modules Metal front plates with cut-outs Blanking plate or device support On a metal front plate with cut-outs Dd381699 Mounting Functional system Functional units and distribution Human-switchboard interface Other devices Pushbuttons and lamps 600 300 Devices Number of devices per row No. of vertical modules Metal front plates with cut-outs DD381690 Pushbuttons and lamps ø 22 mm Metal front plate with knock-outs ø 22 mm (1) 12 2 03914 (1) Harmony Style 4, 5 and 7 Other modular devices 300 DD383480 600 DD383479 Vigirex, Vigilohm and other modular devices 2 2 3 4 5 3 4 5 A A Devices Vigirex (1), Vigilohm (2) No. of vertical modules Rail (48 modules of 9 mm) Cut-out front plates 3 03001 03203 Other modular devices (ammeter, voltmeter, lamp, pushbuttons, etc.) 2 03001 03002 (3) (1) RH10, RH21, RH99, RMH relay and RM12T Multiplexer. (2) EM9, TR5A, SM21, IMD-IM9. (3) For installation at the top or bottom of the enclosure, use a 3-module modular front plate (03203). Other devices behind transparent front plates 600 Transparent front plates 300 4 mod. (H = 200 mm) 6 mod. (H = 300 mm) 9 mod. (H = 450 mm) 12 mod. (H = 600 mm) DD383481 Other devices behind transparent front plates 03342 03343 03344 03345 55 Functional system Front plates, rails, slotted mounting plates Accessories Plain and transparent front plates Nb. of vertical modules 1 2 3 4 5 6 9 12 DD381584 DD381585 Duct L300 DD381582 Enclosure L600 DD381583 Used for Height Plain Transparent Plain Transparent 50 mm 100 mm 150 mm 200 mm 250 mm 300 mm 450 mm 600 mm 03801 03802 03803 03804 03805 03806 03807 03808 03342 03343 03344 03345 03811 03812 03813 03814 03815 03816 03817 - 03352 03353 03354 - Other front plates Nb. of vertical modules 1 2 3 4 5 7 8 9 12 1 row of modular devices 3 rows of modular devices Ventilated With cut-out for fan or filter > see page 64 1 row of modular devices 50 mm 100 mm 150 mm 200 mm 250 mm 350 mm 400 mm 450 mm 600 mm 03202 03203 03204 03205 - 03223 - 03891 03895 03890 - 03213 03214 - Pratic raiser - Accessories for front plates Front plate hinge kit Self adhesive front plate grips DD383950 DD381314 Used for DD381576 56 DB124226 DD381676 Height Accessories for rails and slotted mounting plates Catalogue number Characteristics DD60759 Duct L300 DB124224 Enclosure L600 DB124225 Used for 04224 Set of 5 Heigth 10 mm, length 27 mm Colour: RAL 9001, insulating material Catalogue numbers Characteristics 08585 Set of 2 hinges 01093 Set of 20 white RAL9001 Functional system Front plates, rails, slotted mounting plates Accessories Rails Duct L300 DD383497 DD381371 DD381353 DD381352 DD383497 DD381371 Catalogue numbers Useful length DD381370 Enclosure L600 DD381351 Used for Fixed 03001 432 mm Adjustable 03002 432 mm Rear 03004 432 mm Recessed 03003 432 mm Fixed 03010 180 mm Adjustable 03011 180 mm 9 mm modules number 48 48 48 48 20 20 Useful depth behind front plate 50 mm de 47 à 114 mm 128 mm 158 mm 50 mm de 47 à 114 mm Installation accessories 03005 Set of 2 04206 H = 15 mm Hexagonal spacers DD383506 Brackets DD383505 Catalogue numbers Characteristics 45° supports DD383504 Used for 04207 H = 45 mm 04208 H = 80 mm 03195 H = 9 mm 03196 H = 23 mm 03197 H = 55 mm Adjustable rails DD383292 Catalogue numbers Characteristics DD381310 Rail to be cut 04226 04227 Set of 2 rails, useful length: 1600 mm Rail and 4 modular raisers with 4 holes, dia. 6.4 mm, 450 mm Useful length: 432 mm between centres Slotted mounting plate 03172 6 300 mm 03173 9 450 mm DD381375 Recessed 03171 4 200 mm 420 mm 160 mm DD381369 Flat 03170 4 200 mm 440 mm 140 mm Duct L300 Flat 03175 4 200 mm 172 mm 140 mm Recessed 03176 4 200 mm 152 mm 160 mm 03177 6 300 mm 03178 9 450 mm Clip-nuts For slotted mounting plates DD381312 DD381375 Catalogue numbers Nb. of vertical modules Height Useful length Useful depth behind front plate Enclosure L600 DD381369 Used for M4 M5 M6 Characteristics 03180 03181 03182 Set of 20. Can also be mounted on cable-tie support cat. no. 08876. Offers installation of various devices 57 Functional system Fixing accessories Accessories Clip-nuts M4 M5 M6 Mounting on Characteristics 03180 03181 03182 Slotted mounting plate and also on cable-tie support (08876) Set of 20 Mounting of various devices DD381637 DD381612 DD381313 DD381312 Clip-nuts 03164 03165 03166 Rail 03194 Functional uprights of IP30 / 55 enclosures Set of 20 Set of 20 Self-tapping screws DD384035 Self-tapping screws 03183 Set of 20 Mounting on functionnal uprights M5 Characteristics Hexagonal spacers 03185 03195 Height: 9 mm Set of 4 03186 03196 Height: 23 mm Set of 4 03198 Height: 25 mm Set of 4 Dd380828 Dd380828 Dd380828 Dd380828 M5 M6 M8 Characteristics Dd380828 Hexagonal spacers 03187 03197 Height: 55 mm Set of 4 03199 Height: 40 + 10 mm Set of 4 Universal angle bracket 58 Dd383078 Catalogue numbers Characteristics Dd381577 Universal angle bracket 03581 Set of 2 03583 Set of 6 Functional system Accessories Partitioning Horizontal partitioning The metal partitions are used to: b separate the functional units from one to another b create a physical separation between devices and a terminal block, for example. IP30 and IP55 ducts Catalogue numbers Characteristics DD381419 IP30 and IP55 enclosures DD381418 Used for 04331 04332 Metal. It is mounted directly on the functional uprights. Lateral and rear cut-outs are available for cable running or the installation of busbars at the rear of the switchboard. Vertical partitioning The metal partition creates a physical separation between the device compartment and a wide duct. It is used to: b separate the devices from busbars or a distribution block installed in the duct, b set up a special zone for terminal blocks in the duct. Wall-mounted enclosures and IP55 duct DD383119 Cat. no. Description Wall-mounted, floor-standing enclosures and IP30 duct DD383509 Used for 04330 Can be used for partitioning up to 33-modules. It can be cut to length every 150 mm. 08384 Metal. There are cut -outs for cable running. Quantity to order according to height. Nb. of vertical modules 7 11 of 50 mm Height (mm) 450 650 Quantity 1 15 19 23 27 33 850 2 1050 1250 3 1450 1750 59 Functional system Accessories Cable running Straps and covers Covers for vertical cable straps Dd381618 Dd381621 04264 Set of 12 Covers for horizontal cable straps Dd381633 Dd381628 Catalogue numbers Characteristics Horizontal cable straps Dd383484 Vertical cable straps Dd383485 Type 04263 Set of 2 x 1 m 04239 Set of 12 Have the same capacity as 60 x 30 mm trunking 04243 Set of 4 covers of 430 mm Trunking supports Adaptable support for horizontal trunking Dd381623 Dd381626 Dd382922 Dd383486 Horizontal trunking supports Dd383477 Vertical trunking supports Dd383476 Type Catalogue numbers Characteristics 04265 Set of 12 04255 Set of 12 04256 Set of 10 Aligns the cover of a horizontal trunking section (H = 60 or 80 mm) with that of a vertical trunking section (H = 80 mm) Note: not designed for use with Pack enclosures. Trunkings 60 Horizontal trunkings 60 x 30 mm Dd381639 Catalogue numbers Characteristics Vertical trunkings 80 x 60 mm Dd381640 Type 04267 04257 Set of 18 L = 2000 mm Set of 4 L = 450 mm Supplied with supports Functional system Cable running Accessories Cable trunkings for doors Catalogue numbers Characteristics DD381641 Cable trunkings DD380863 Flexible trunkings for wiring to door DD381643 Type 04235 L = 500 mm, Inner diameter = 19 mm 04233 Set of 30 adhesive trunkings 30 x 30 mm, L = 2000 mm Grommets for wiring through front DD380864 DD380865 Grommets 04234 Set of 10. For wiring through front. Catalogue number Characteristics Cable-tie supports Cable-tie support adapters DD381171 C-shaped cable-tie supports for wall mounted or floor standing enclosures and ducts DD383424 Catalogue numbers Characteristics Cable-tie supports in a duct DD383423 Cable-tie supports for wall-mounted or floor-standing enclosures 08867 08868 08783 08866 b Set of 2 b Supplied with hardware for mounting on the functional uprights of the enclosure. b Set of 4 b Supplied with hardware for mounting on the functional uprights of the duct. b L = 1600 mm, can be cut to length as needed. b Cables secured by ties or cable clamps. b Supplied with hardware for mounting on the functional uprights of the enclosure or duct. b Set of 2 b Makes it possible to tie down the cables next to the gland plate and gain one module in height. DD381820 Used for 61 Functional system Accessories Switchboard lighting Fixed lighting 600 300 Catalogue number Presentation Characteristics DD381719 Fixed lighting 08964 This system is generally used to illuminate the front of a switchboard. b v v v v b b b The kit is made up of: a base, a neon tube, a front plate with cut-out (1 module), a door contact. Supply voltage: 220/240 V Power rating: 8 W Height: 1 vertical module (50 mm) Switchboard portable lamp DD381675 Switchboard portable lamp Catalogue number Presentation Characteristics 62 08965 b Lamp with a magnetic base for installation behind a door or directly on the cubicle framework. b Supplied without a power cord. b It does not take up any useful space in the switchboard. b Supply voltage: 220/240 V b Power rating: 11 W Functional system Finishing parts Accessories Clip-on labels Engraving plates DD381714 DD381757 Identification labels IERE LUM 08913 08915 08917 18 x 35 18 x 72 25 x 85 b Set of 12 b The clip-on support is supplied with a paper label and a transparent cover. b It clips onto the front plate horizontally or vertically and can be screwed to any support (plain door, plain front plate, etc.). 08905 08906 08903 08904 24 x 180 36 x 180 24 x 432 36 x 432 b Set of 12 b The adhesive label holders are supplied with a paper label and a transparent cover. 13735 b b v v DD381752 DD381751 Catalogue numbers Dimensions (mm) Characteristics Symbol sheets DD381715 Adhesive labels 08914 08916 08918 18 x 35 18 x 72 25 x 85 b Set of 12 b These plates simply replace the paper labels. DD381753 Catalogue numbers Dimensions (mm) Characteristics IERE LUM 13736 Set of 10 adhesive symbol sheets Standard symbols: loads: sockets, lights, heating units, etc. rooms: bedroom, bathroom, etc. b Set of 10 adhesive symbol sheets b Special symbols: v loads: lightning arrestor, gate, swimming pool, etc. v rooms: technical room, computer room, etc. Adhesive labels for mimic diagrams Earth symbols 01006 01009 01007 01008 Catalogue numbers Characteristics Switchboard identification plate Adhesive drawing holder DD381008 Accessories DD381208 01005 Set of 10 Outgoing arrows Incoming arrows Transformers DD381721 Catalogue numbers Characteristics Lines, 900 mm long (7 mm thick) Touch-up paint brush 08900 Colour: RAL 9001 08963 Colour: RAL 9001 08961 Colour: RAL 9001 63 Functional system Accessories Management of the internal temperature Ventilation In most cases and notably for IP30 switchboards, convection takes place naturally and does not require fans. However, when the switchboard is installed in temperate environments or when the degree of protection is high (IP55), ventilation accessories are indispensable. For more in-depth information on selecting air-conditioning accessories and the thermal management of switchboards. > see page 158 to page 167. Catalogue numbers Installation 08987 08988 Generally installed at the bottom of floor-standing enclosures: b by cutting out a side panel; b or by using the front plate with cut-out for fan, directly clipped on (03890). Characteristics The set comprises the fan with a grill and a filter. b Power rating: 70 W. b Input voltage: 230 V. b Noise level: 69 db. b Degree of protection: IP54. b Weight: 3 kg. b Unimpeded throughput: 460 m3/h. b Throughput with counterpressure (grill + standard filter, cat. no. 08988): 350 m3/h. Supplied with standard filter. b Maximum throughput 350 m3/h. b Degree of protection: IP54. DD381723 DD381724 DD381704 Grill with filter DD381703 Fan Dimensions Front plate for fan or grill DD60759 Front plate for fan or grill Filters Catalogue numbers Characteristics Standard filters 08989 Set of 5 (for replacement) Fine filters 08990 Set of 5 (for replacement) Ventilated front plate Catalogue number Characteristics 03890 Front plate with cut-out for fan or filter. b Degree of protection: IP30. b Height: 7 modules. Dd381676 Ventilated front plate 03891 03895 1 vertical module, 3 vertical modules, H = 50 mm H = 150 mm Surface area of the openings 80 cm2 250 cm2 Characteristics Degree of protection: IP30. Located at the top and bottom of the switchboard, IP30 ventilated front plates facilitate natural convection in the switchboard. Catalogue numbers Height 64 Management of the internal temperature Heating elements The resistors prevent condensation, corrosion and superficial leakage currents. They maintain a positive temperature in the enclosures when external temperatures drop very low. Catalogue numbers Power rating Characteristics 08992 DD381573 Heating resistor DD381574 Accessories 08993 08994 55 W 90 W 250 W b Horizontal or vertical mounting. b Aluminium case with fins. b Temperature: v turns off at 60 °C, v turns on at 25-30 °C (temperature of the resistor itself). b Equipped with a symetrical rail for rapid mounting (clips on). b Input voltage: 230 V. Regulating Used to control the temperature inside electrical switchboards in conjunction with heating resistors and fans. Thermostat DD381575 Functional system Catalogue number Characteristics 08998 b Setting range: +5 °C to +60 °C. b Input voltage: 230 V. b Fixing: clips onto a modular rail. 65 Functional system Panorama of the solution Distribution blocks Prisma Plus G System > For incoming devices > For rows of modular devices 160 to 250 A Polybloc 125 to 160 A Distribloc Distribution - Spring terminals for electrical connections that stay tight - Front designed to integrate perfectly with modular devices 63/200 A Multiclip - Reliable spring-terminal connections requiring no maintenance - Reliable spring-terminal connections for outgoing circuits, requiring no maintenance - Fast installation - Horizontal or vertical installation in minimum space - Easy upgrades through replacement or addition of devices - Easy balancing of phases 160 to 630 A multi-stage distribution block 80 to 125 A comb busbars - Fast and direct connections, adaptable to all needs - Fast, economical connections 63/160 A adaptable earthing terminal blocks - Traditional, highly polyvalent solution - Many installation possibilities 66 - Innovative solution Functional system Distribution Panorama of the solution Customised organisation of your switchboard > Busbars up to 630 A for all switchboard architectures Powerclip busbars: compact for fast upgrades. Flat busbars: for traditional distribution. Prefabricated connections, optimised and fully insulated. Rear busbars. > Row distribution blocks for modular devices Lateral busbars. The bars are staggered for easy access to connection points. > Wiring routing components Comb busbars: a simple, cost-effective solution. Multiclip: a fast, flexible and reliable solution. Cable straps: a fast and efficient solution. Trunkings: for a neat finish. Comb busbars are fully insulated. Device can de connected in a single operation. 80 A Multiclip. Snapped onto the back of rails, cable straps are a solution for clear and well-organised cabling. They can be used for all configurations, whatever the number of cables and cable cross-sections. A cover protects the wiring and provides a neat finish. Horizontal and vertical, with different cross-sections, they are interconnected by adjustable trunking supports. 200 A Multiclip. The Multiclip distribution block snaps easily onto the back of the rails. All types of modular devices can be mixed in the same row and phase balancing is simple. It's easy to change or add devices. > Centralised distribution blocks for switchboard incomers 160 A Distribloc: practical and aesthetic. Répartiteur monobloc modulaire à connexion rapide. 160 A Polybloc: "à la carte" distribution block. 160 A multistage distribution block: a traditional solution. Modular combinable components for fast connections. Installation on modular rail on mounting-plate. Screw-terminal connections. Polybloc 250 A: modular and compact. Installed directly downstream of Compact circuit breakers and Interpact switches without taking up any extra vertical modules. Fast connections in spring-loaded terminals. 67 Functional system 630 A insulated busbar Distribution Non-Centralised distribution Compact busbars, IPxxB, ready for installation in the switchboard (supplied with supports and extremity obturators) PD390337 PD390545 Powerclip busbars 160 / 630 A ETP H12 channelled copper bars with threaded M6 holes every 25 mm, can be cut every 200 mm PD390546 Tap-off blocks for 6 mm² and 10 mm² cable Bars mounted on insulated bases that screw to the functional upwrights Wide choice of prefabricated and tested connections Clip-on covers that block off the connected cable lugs PD391009 Clip-on covers to protect against direct contacts from the front (IPxxB). They can be easily cut for the connections to the devices The ends are protected by extremity obturators 200 A connection for Multiclip distribution block Powerclip busbars Additional accessories* 3P W = 1000 mm W = 1400 mm 4P W= 1000 mm W = 1400 mm 2 Powerclip supports + 2 extremity obturators + mounting hardware 2 IPxxB clip-on covers, L= 200 mm Spare parts* * For more information > see page 103 Rating 160 A 400 A 630 A 04112 04117 04122 04127 01210 04113 04118 04123 04128 01210 04114 04119 04124 04129 01211 01201 01201 01201 01201 Electrical characteristics Rated withstand current max. 160 A 250 A 400 A 630 A 250 A 04111 04116 04121 04126 01210 Rated level Short-time withstand current Icw Withstand peak Ipk Insulation Ui Impulse withstand voltage Uimp (kA rms / 1 s) (V) (kV) 10 13 20 25 (kÂ) 30 30 52,5 52,5 750 750 750 1000 8 8 8 8 Choice of connections depending on devices Device to connect Compact NSX Interpact INS-INV Fupact INS NG NSX400 horizontal NSX630 horizontal NSX400/630 vertical with or without Vigi NSX100/250 horizontal with or without Vigi NSX100/250 vertical without Vigi NSX100/250 vertical with Vigi INS-INV250 horizontal INS-INV320/400 horizontal INS-INV500/630 horizontal INS-INV250 vertical INS-INV320/630 vertical INF100/160 horizontal INF100/160 vertical ISFT 100/250 vertical or horizontal INS40/125 3P 4P INS160 NG125 NG160 Vigi NG160 NSA160 C120, iC120 Multiclip 63/80/160 A 200 A Modular devices 68 Catalogue numbers (see details on next page) 04070 04071 04074 + connection must be made (in enclosure) or 04074 + 04073 (in duct) 04060 04061 + 04062 (in enclosure) or 04061 + connection must be made (with rotary handle in enclosure) or 04061 + 04064 (in duct) 04061 + connection must be made (in enclosure)04061 + 04064 (in duct) 04060 04070 04071 04061 + 04062 (in enclosure) or 04061 + 04064 (in duct) 04074 + connection must be made (in enclosure) or 04074 + 04073 (in duct) 04155 + connection must be made (3P) or 04156 + connection must be made (4P) 04061 + connection must be made 04061 + connection must be made 04145 + 28947 04145 + 28948 04147 or 04148 or 04146 04145 or 04147 or 04148 or 04146 04147 or 04148 or 04146 04148 04147 or 04148 or 04146 04147 or 04148 04151 or 04152 04021 04151 or 04152 Functional system 630 A insulated busbar Distribution Non-Centralised distribution Busbar connection DD380593 DD380522 Description Power supply block with connection Universal power supply block + prefabricated connections Universal power supply block + connections must be made (possibility to use insulated flexible bars) DD381659 Set of 4 125 A connections, L= 230 mm 35 mm² ferrule + 45° angle lug ( insulated covers IPxxB, cat. No 04150) Set of 4 160 A connections, L= 230 mm 45 mm² ferrule + 45° angle lug ( insulated covers IPxxB, cat. No 04150) One-piece connection 3/4P - 160 A, L = 150 mm b Fast connection to busbars b Equipped with male fittings one end for tunnel terminals b Respects the degree of protection IPxxB b Neutral is clearly indicated (blue) Cat. no. 04060 Compact NSX100/250 toggle in enclosure Interpact INS-INV250 vertical in enclosure Compact NSX100/250 with or without Vigi in duct Interpact INS-INV250 vertical in duct Compact NSX400/630 with or without Vigi in duct Interpact INS-INV320/630 in duct Compact NSX100/250 rotary handle in enclosure Fupact INF100/160 vertical Fupact ISFT Compact NSX400/630 with or without Vigi in enclosure Interpact INS-INV320/630 in enclosure NSX, Multiclip 200 A, Fupact 04061 + 04062 04061 + 04064 04074 + 04073 04061 04070 04071 04074 > see page 74 NG125, NSA equipped with tunnel terminals or comb, 04145 INS with tunnel terminals Catalogue numbers 28947 or 28948 NSA160, INS160, 04146 NG125, NG160 NSA160, NG160 (located on left-hand side), NG125, INS160, C120, iC120 04147 NSA160, NG160 (located on left-hand side), Vigi NG160 (located in the middle), NG125, INS160, C120, iC120 04148 Fupact INF100/160 3P horizontal 04155 Fupact INF100/160 4P horizontal 04156 12 tap-off blocks for 6 mm² and 10 mm² cable Respects the degree of protection IPxxB 12 tap-off blocks for 16 mm² Respects the degree of protection IPxxB All type of device, equipped with tunnel terminals, 160/200 A Multiclip 04151 All type of device, equipped with tunnel terminals, 160/200 A Multiclip 04152 Set of 4 200 A connections Supplied with mouting hardware + Insulating cover Multiclip 200 A 04021 + 04150 One-piece connection 3/4P - 160 A, L = 440 mm b Fast connection to busbars b Equipped with male fittings one end for tunnel terminals b Respects the degree of protection IPxxB b Neutral is clearly indicated (blue) Additional 35 mm² block + connection must be made Accessories Connection cover DD381385 DD383472 DD383498 DD381405 DD383276 DD383295 DD383274 DD383294 Universal power supply block + insulated flexible bars DD381379 > see page 74 Allows connection of Compact NSX100/250 horizontal with or without Vigi Interpact INS-INV250 horizontal Compact NSX400 horizontal Interpact INS-INV320/400 horizontal Compact NSX630 horizontal Interpact INS-INV500/630 horizontal Cat. no. b Clip-on covers that block off the connected 04150 cable lugs and can be cut as needed. b They maintain IPxxB with 90° angle lugs and/ or cable sizes from 10 to 25 mm². b 8 IPxxB covers for Powerclip busbars 8.8 class mounting hardware Set of 20 CHC M6 x 12 mm screws for Powerclip busbars Cat. no. 04158 69 Functional system Distribution 400 A rear busbars Non-Centralised distribution PD390532 Rear busbars 160 / 400 A Dd381192 Presentation The rear busbars are mounted directly on the uprights of the framework. There are three and four-pole versions with ratings from 160 to 400 A. Available in two lengths, 1000 and 1400 mm, they can be cut as needed. The connection with a Compact or Interpact incoming device occupies two vertical modules (50 mm each). Dd381388 Barrier protect against direct contact with connections. Dd381389 Flat, copper bars with threaded M6 holes every 25 mm for connection along the entire length of the busbars. b Connection by: v 16 mm² to 50 mm² flexible cables, with crimped lugs v insulated flexible bars Bars supports in insulating material direct installation on the functional uprights. > see page 74 Rating Bars (Set of 4) Insulating support (1) (2) Accessories 160 A 250 A 400 A Cross-sectional areas of conductors Length 1000 mm 1400 mm Catalogue numbers 15 x 5 mm 04161 04171 04191 20 x 5 mm 04162 04172 04191 32 x 5 mm 04163 04173 04191 Barrier, H = 100 mm, supplied with mounting hardware 04198 04198 04198 (1) The insulating supports can receive a fifth bar, 15 x 5 mm or 20 x 5 mm to create an earth bar. (2) Rating (A) 160 250 400 Size of bars Distance between support centres (mm) (3) (mm) Icw (kA rms / 1 s) y 10 y 13 y 15 y 20 y 25 15 x 5 20 x 5 450 300 225 32 x 5 (3) Multiclip 200 A distribution blocks equipped with connections (04029) can be used as intermediate supports (200 mm max.distance between centres) in addition to the top and bottom supports (04191). Electrical characteristics Rating Icw (kA) Short-time withstand current Icw 160 A 250 A 400 A 70 (kA rms / 1 s) 10 13 15, 20, 25 Ui (V) Rated peak withstand current Rated insulation level (kÂ) 30 40 55 (V) 1000 1000 1000 Functional system Distribution 400 A rear busbars Non-Centralised distribution Connection between busbar DD383511 DD383510 Designation For the connection of Catalogue numbers Set of 4 rear busbar connection - 125 A, L = 230 mm A 35 mm² ferrule for connection to tunnel terminals + A 45° ring lug b A comb busbar b NG125, NSA and INS equipped with tunnel terminals 04145 Set of 4 rear busbar connection - 160 A, L = 250 mm A 45 mm² ferrule for connection to tunnel terminals + A 45° ring lug NSA160 04146 Set of 4 rear busbar connection - 200 A Multiclip 200 A 04029 Set of 4 copper angle brackets - 250 A Electrical connections between two sets of rear busbars. 04190 Insulated flexible bars NSX100 NSX160/250 NSX400 NSX630 INS125/160 INS250 INS400 INS630 200 A multiclip Fupact 250 Fupact 400 Fupact 630 04742 04743 04751 04753 04742 04743 04751 04752 04743 04746 04751 04753 > see page 74 Accessories 8.8 class mounting hardware DD381398 20 bolts M6x20 + 20 nuts + 40 contact washers 40 screws M6x16 + 40 contact washers Catalogue numbers 04194 04195 Set of 4 connectors for copper or aluminium cables Catalogue numbers 07051 250 A for rigid cables 185 mm² 07052 400 A for rigid cables 300 mm² 07053 E56851 E56852 180 A for rigid cables 70 mm² E56850 E13771 DD381659 DD381458 Note: Multiclip 200 A distribution blocks equipped with connections (04029) can be used as intermediate supports (200 mm max. distance between centres) in addition to the top and bottom supports. 71 Functional system 630 A Multi-stage busbars in duct Presentation The multi-stage busbars are installed in a 300 mm wide duct. They are particularly useful for distribution to two enclosures on each side of the duct. All connection points are easily accessible from the front. The inclination of the bars facilitates connections and improves cable running. There are three and four-pole versions with ratings from 160 to 630 A. Available in two lengths, 1000 and 1400 mm, they can be cut as needed. Busbar 160 / 630 A PD390533 Non-Centralised distribution Dd381396 Distribution Dd381388 Front barrier protect against direct contact with connections (in option). Dd381395 Flat, copper bars with threaded M6 holes every 25 mm for connection along the entire length of the busbars. b Connection: v 16 mm² to 50 mm² flexible cables, with crimped lugs v insulated flexible bars Bars supports in insulating material direct installation on the functional uprights of the duct. > see page 74 Rating Bars (Set of 4) Insulating support (1) (2) Accessories (1) Rating Size of bars (A) (mm) 160 250 400 630 15 x 5 20 x 5 32 x 5 32 x 8 Cross-sectional areas of conductors Length 1000 mm 1400 mm Catalogue numbers Barrier, H = 1500 mm 160 A 15 x 5 mm 04161 04171 04192 04197 250 A 20 x 5 mm 04162 04172 04192 04197 400 A 630 A 32 x 5 mm 04163 04173 04192 04197 32 x 8 mm must be made 04174 04192 04197 Distance between support centres (mm) Icw (kA rms / 1 s) y 10 y 13 y 15 y 20 y 25 450 300 300 (3) (2) Supplied with mounting hardware for barrier, cat.no. 04197. (3) With Icw 25 kA rms / 0,6 s.: distance between supports 300 mm (Rating 400 A with bars 32 x 5 mm only). Electrical characteristics Rating Icw (kA) Short-time withstand current Icw 160 A 250 A 400 A 630 A 72 (kA rms / 1 s) 10 13 15, 20 25 Ui (V) Rated peak withstand current Rated insulation level (kÂ) 30 40 55 55 (V) 750 750 750 750 Functional system Distribution Non-Centralised distribution 630 A Multi-stage busbars in duct Connection between busbar For the connection of Catalogue numbers b Compact NSX 100/250 vertical in duct b Interpact INS-INV 250 vertical in duct 04065 Set of 4 rear busbar connection - 630 A b Compact NSX 400/630 vertical in duct b Interpact INS-INV 320/630 vertical in duct 04075 Set of 4 rear busbar connection - 200 A Multiclip 200 A 04024 Insulated flexible bars NSX100 NSX160/250 NSX400 NSX630 INS125/160 INS250 INS400 INS630 200 A multiclip Fupact 250 Fupact 400 Fupact 630 04742 04743 04751 04753 04742 04743 04751 04752 04743 04746 04751 04753 > see page 74 Accessories 8.8 class mounting hardware Dd381398 DD381659 Dd383499 Dd382305 Description Set of 4 rear busbar connection - 250 A 20 bolts M6 x 20 + 20 nuts + 40 contact washers 40 screws M6x16 + 40 contact washers Catalogue numbers 04194 04195 73 Functional system Distribution Insulated flexible bars Non-Centralised distribution Dd381659 The insulated flexible bars are tested in a type-tested switchboard environment. Their design takes into account the switchboard architecture where they are often in close proximity to a protection device (circuit breaker or fuse) with significant heat losses. The sizes for the flexible bars indicated below take into account the heat losses of Schneider Electric devices in a Prisma Plus switchboard. Dd382008 Characteristics Length Rated insulation level (Ui) 1800 mm 1000 V Connection between device busbar The flexible bars are determined taking into account the connected device, whatever the internal temperature of the switchboard. The bar sizes indicated below take into account the derating curves of devices. Device NSX100 NSX160/250 NSX400 NSX630 INS125/160 INS250 INS400 INS630 200 A multiclip Fupact 250 Fupact 400 Fupact 630 Size (mm) 20 x 2 20 x 3 (1) 32 x 5 32 x 8 20 x 2 20 x 3 32 x 5 32 x 6 20 x 3 24 x 5 32 x 5 32 x 8 Catalogue numbers 04742 04743 04751 04753 04742 04743 04751 04752 04743 04746 04751 04753 (1) To connect a Compact NSX250 to Powerclip busbars, use a 24 x 5 mm flexible bar (04746). Connection between busbars Flexible bars are designed for connections between busbars taking into account the following characteristics: b a maximum temperature of 60 °C inside the switchboard. This corresponds to the average temperature inside a switchboard for an ambient temperature of 35 °C b the maximum withstand temperature for the insulating material is 125 °C. Ie* Max. 200 A 250 A 400 A 520 A 580 A 660 A * Rated operational current. 74 Size (mm) 20 x 2 20 x 3 24 x 5 32 x 5 32 x 6 32 x 8 Catalogue numbers 04742 04743 04746 04751 04752 04753 Functional system Distribution Distribution block 160 A Polybloc The 160 A Polybloc is made up of individual elements that can be used alone or with others to make two-pole, three-pole or four-pole distribution blocks. Mounting is very fast. It clips onto a modular rail and is supplied by cables via a tunnel terminal. The connection spring terminals are slanted to facilitate cable entry and bending of the flexible and rigid cables. It is supplied with a cover that also guides the cables. Dd383658 Dd381392 Dd383300 Dd382981 160 A Polybloc Catalogue number Total connection capacity 04031 b Supply direct to a tunnel terminal, for cables up to 70 mm². b Distribution via cables, up to 6x16 mm² cables. Clip onto a modular rail. 70 Dd384321 Installation Space required 95 36 Rated insulation level (Ui) Impulse withstand voltage (Uimp) Short-circuit withstand current 750 V 8 kV The reinforced breaking capacity due to cascading in circuit breaker combinations is maintained. The worst-case situations were tested.The electrical characteristics are perfectly compatible with the connected devices. Neither the temperature derating curves nor the performance levels of the circuit breakers and switch-disconnectors are altered. Choice of accessories depending on devices Device to connect Fupact INF100/160 vertical ISFT vertical INS NG C120, iC120 INS40/125/160 NG160 Catalogue numbers Connection must be made + rail 03002 Connection must be made + rail 03002 or 03011 04149 04149 04149 Distribution block connection Description For the connection of Four 160 A connections for modular INS40/125/160 devices, W = 380 mm NG160 Two 45 mm² end fittings for C120, iC120 tunnel terminals Cat. no. 04149 Accessories Adjustable modular rails Dd381371 DD381399 Centralised distribution For wall-mounted or floor-standing enclosure For a duct Cat. no. 03002 03011 75 Functional system Distribution block Distribution Centralised distribution DD381399 250 A Polybloc Applications The Polybloc distribution block is designed for installation directly downstream of Compact circuit breakers and Interpact switch-disconnectors devices up to 250 A. It can be rapidly mounted in the horizontal position. Electrical connections are made directly to the device terminals. It has the same width as the devices and does not take up any additional space in the switchboard. The connection terminals are slanted to facilitate cable entry and not exceed the bending radius of the flexible and rigid cables. 04033 04034 Supply directly to the terminals of the Compact NSX and Interpact INS devices up to 250 A. Directly on the mounting plates of horizontally mounted Compact NSX100/250 and Interpact INS250 devices in the enclosures. It can also be mounted downstream of vertically mounted Compact NSX100/250 and Interpact INS250 devices in the enclosures. In this case, the Polybloc is mounted on a depth-adjustable modular rail 105 140 138 138 63 63 H L P DD381406 Space required Rated insulation level (Ui) Impulse withstand voltage (Uimp) Short-circuit withstand current DD380745 Catalogue numbers Total connection capacity Installations Dd381346 DD380780 4P PD390549R 3P 750 V 8 kV The reinforced breaking capacity due to cascading in circuit-breaker combinations is maintained. The worst-case situations have been tested. Choice of accessories depending on devices Device to connect Compact Interpact NSX100/250 with or without Vigi horizontal NSX100/250 with or without Vigi vertical INS-INV250 horizontal INS-INV250 vertical INS-INV250 Lateral handle vertical Catalogue numbers 04033 (3P) 04034 (4P) 04033 (3P) 04034 (4P) + rail 03002 or 03011 04033 (3P) 04034 (4P) 04033 (3P) 04034 (4P) + rail 03002 or 03011 04033 (3P) 04034 (4P) + rail 03002 or 03011 + spacer 04037 Accessories Dd381371 Adjustable modular rails For wall-mounted or floor-standing enclosure For a duct Copper spacer Catalogue numbers 03002 03011 Catalogue number 04037 35 mm² additional blocks These blocks with screw terminals can be mounted on the 250 A Polybloc for connection of two 35 mm² cables per phase. DD381403 Designation 76 Catalogue numbers 35 mm², 3P additional blocks (3 blocks) 04155 35 mm², 4P additional blocks (4 blocks) 04156 Functional system Distribution Distribution block Centralised distribution Distribloc 125 et 160 A 125 A 160 A PD390657 PG123021 054947 Dd383474 Rated operational current (Ie) 40 °C + Distribution block 4P Connections block Total connection capacity (ø for flexible cables) Connections characteristics Installation Dd381608 Dimensions From the top or from bottom From the top or from bottom 04045 04046 04047 Supplied b Incoming connection in a terminal for 10 to 35 mm² cable per phase b Distribution spring terminals: v 7 outgoers from 1.5 to 4 mm2 v 3 outgoers from 2.5 to 6 mm2 v 2 outgoers from 4 to 10 mm2 b Distribution in tunnel terminal: v 1 outgoer from 4 to 16 mm2 For INS100/160 or NSA160, For NG125 and INS125 Installed on the right or left. Set of four flexible Set of 4 flexible connections 35 mm2, L = 210 mm connections supplied with the distribution block b Clipped onto a modular rail: 12 modules (9 mm each) b Screwed to plain or slotted backplate. Distances between centres = 100 x 75 mm. Rated insulation level (Ui) Impulse withstand voltage (Uimp) Short-circuit withstand current Degree of protection Accessories supplied Dd381609 Supply Catalogue numbers 750 V 8 kV The reinforced breaking capacity due to cascading in circuit breaker combinations is maintained. The worst-case situations have been tested. IPxxB An identification label Adhesive labels for phase identification Distribloc 63 A Distribution block 4P Installation Dimensions Rated insulation level (Ui) Rated operational voltage (Ue) Impulse withstand voltage (Uimp) Short-circuit withstand current Degree of protection From the top From bottom 04040 04041 b Incoming connection in a tunnel terminal for 25 mm² cable per phase b Distribution spring terminals: v 4 outgoers from 6 mm2 for each phase v 12 outgoers from 6 mm2 for the neutral b Clipped onto a modular rail: 8 modules (9 mm each) Dd122616 Incoming Catalogue numbers Total connection capacity (ø for flexible cables) PB104499 63 A PB104500 Rated operational current (Ie) 40 °C 500 V CA 440 V CA 6 kV Up to the breaking capacity of Schneider Electric circuit breakers, even in cascading configuration IP20 77 Functional system Distribution Distribution block Centralised distribution Multi-stage distribution block 160 / 630 A Installation Composition Busbar size Space required Rated insulation level (Ui) Impulse withstand voltage (Uimp) Rated short-time withstand current (Icw) Rated peak withstand current (Ipk) 78 400 A 630 A 04052 04053 04054 04055 b 13 threaded M6 holes for outgoers b Four 12.2 mm diameter holes to supply the distribution block. b Screwed horizontally onto the functional uprights of wall-mounted and floor standing enclosures. b Screwed vertically onto the functional uprights of the 300 mm wide duct. b Screwed to plain or slotted backplate. b Two staggered supports made of an insulating material b Four slanted copper bars with holes every 25 mm b M6 hardware b One IPxxB insulating barrier for the front. 15 x 5 mm 20 x 5 mm 32 x 5 mm 32 x 8 mm DD381344 Catalogue numbers Total connection capacity 250 A Dd381343 160 A DD381342 PD390659 Rated operational current (Ie) for 40 °C 750 V 8 kV 10 kA rms /1 s 30 k 13 kA rms /1 s 30 k 20 kA rms /1 s 40 k 25 kA rms /1 s 40 k Functional system Distribution block Distribution Centralised distribution Multi-stage distribution block 40 / 125 A 4P 058930d 2P 058923d Distribution block 13506 100 A 2P 1 term 16 mm2 Catalogue numbers Additional neutral bar Rated operational current (Ie) Pole number Supply (screw terminal) per phasis Distribution (screw terminal) per phasis 13507 125 A 2P 1 term 25 mm2 13508 13516 40 A 4P 2 term 10 mm2 13510 13515 100 A 4P 1 term 16 mm2 13512 13517 125 A 4P 1 term 25 mm2 3 term 6 mm2 3 term 10 mm2 5 term 6 mm2 11 term 6 mm2 3 term 6 mm2 5 term 6 mm2 5 term 10 mm2 3 term 10 mm2 5 term 10 mm2 2 term 16 mm2 2 term 16 mm2 7 modules (9 mm) 12 modules (9 mm) 10 modules (9 mm) 7 modules (9 mm) 12 modules (9 mm) 40 x 62 x 50 mm 40 x 107 x 50 mm 81 x 89 x 50 mm 81 x 62 x 50 mm 81 x 107 x 50 mm b Rated insulation level (Ui): 500 V CA b Short-circuit withstand current: compatible with all Schneider Electric circuit-breakers. b With other device, it is advised to check the energy limiting curve of the upstream device b Rated short-time withstand current (Icw): 3.5 kA rms /1 s b Rated peak withstand current Ipk = 20 k Designed to be clipped onto rail Dimensions (H x W x P) Electrical characteristics Installation 13514 13518 4P 1 term 25 mm2 7 term 6 mm2 7 term 10 mm2 2 term 16 mm2 15 modules (9 mm) 81 x 134 x 50 mm Joinable distribution blocks 80 A Catalogue numbers Pole number Supply per phasis Distribution per phasis Electrical characteristics Installation Dimensions 14936 14938 1P 1P 2 1 screw terminal 35 mm2 1 screw terminal 25 mm 4 screw terminal 16 mm2 4 screw terminal 25 mm2 b Rated operational current (Ie): 80 A b Rated insulation level (Ui): 500 V CA Designed to be clipped onto rail 2.5 modules 18 mm 030925d 2P 030925d 1P 030925d Distribution block 14937 2P 2 x 2 screw terminal 25 mm2 2 x 4 screw terminal 16 mm2 14939 2P 2 x 2 screw terminal 35 mm2 2 x 4 screw terminal 25 mm2 5 modules 18 mm 79 Functional system Distribution Distribution block Centralised distribution Multiclip 63 / 80 A PD384088 04000 b Rating: 80 A b 4 P b 48 modules (9 mm) 24 modules (18 mm) Tunnel terminals up to 25 mm2 b Spring terminals: v 6 for each phase (6 mm2) v 18 for the neutral (6 mm2) DB124195 By clipping at the rear of a modular rail, or by screwing. 100 mm long bared copper connections 10 of 4 mm2 + 6 of 6 mm2 6 mm2 bared copper connections (12 blue + 12 black) DB124196 Installation PD381661 Supply Distribution 04008 b Rating: 63 A b 4 P b 24 modules (9 mm), 12 modules (18 mm) Tunnel terminals up to 25 mm2 b Spring terminals: v 4 for each phase (2 x 4 mm2 + 2 x 6 mm2) v 8 for the neutral (4 x 4 mm2 + 4 x 6 mm2) By clipping at the rear of a modular rail, or by screwing. DB404608 Catalogue numbers Characteristics 80 A PD104505 63 A DD383403 Multiclip 63 / 80 A Accessories supplied 80 Functional system Distribution block Distribution Centralised distribution Multiclip 160 / 200 A Distribution Installation Accessories supplied DD381673 DD381671 DD381670 DD381672 Connections to the block Description Supplied with Catalogue numbers Connection 4P 200 A (supplied with mounting hardware) Powerclip busbars 04021 Connection 4P 200 A (supplied with mounting hardware) Busbars in duct 04024 Connection 4P 200 A (supplied with mounting hardware) Connection 4P 160 A for Multiclip 1/2 row A rear busbars 04029 Device 04030 4 terminal covers for 200 A Multiclip 01202 Spare parts Description DD384505 Supply 04012 04013 04014 04018 b 2P b 3P b 4P b 4P b Rating: 200 A b Rating: 200 A b Rating: 200 A b Rating: 160 A b 48 modules (9 mm), b 48 modules (9 mm), b 48 modules (9 mm), b 24 modules (9 mm), 24 modules (18 mm) 24 modules (18 mm) 24 modules (18 mm) 12 modules (18 mm) 1/2 row b Rated insulation level (Ui): 750 V b Impulse withstand voltage (Uimp): 8 kV b Short-circuit withstand current: the reinforced breaking capacity due to cascading in circuit breaker combinations is maintained. The worst-case situations have been tested. v 10 mm² cable outgoer: Imax = 50 A v two 10 mm² cables: Imax = 63 A. b From Powerclip insulated busbars in a wall-mounted or floor-standing enclosure (04021) b From lateral, channelled busbars in a cubicle (connection must be made) b From busbars in the duct of a wall-mounted or floor-standing enclosure (04024) b From busbars in the rear of a wall-mounted or floor-standing enclosure (04029) b 12 connection points for b 12 connection points for each phase b 6 connection points phase and neutral b 18 connection points for the neutral for each phase b 9 connection points for the neutral b Clipped onto the rear of modular rail b Screwed to plain or slotted backplate. b 100 mm long, bared 10 mm² copper connections b 2 sets of 12 connections b Protection covers for the supply terminals (IPxxB) 100 mm long, bared 10 mm² b The hardware required for the supply terminals copper connections b Protection covers for the supply terminals (IPxxB) b The hardware required for the supply terminals Dd383472 Catalogue numbers Characteristics 160 A Dd383617 PD390661R Multiclip 160 / 200 A 200 A Catalogue number 81 Functional system Comb busbars Distribution Centralised distribution Comb busbars for DPN Lateral tooth-caps Tooth-caps Insulated connectors 21094 DD382981 Comb busbar Catalogue numbers Characteristics 2-pole 21086 3-pole 21090 21092 24 modules (9 mm) 48 modules (9 mm) 12 modules (18 mm) 24 modules (18 mm) Rating: 80 A Quantity per catalogue numbers: 1 4 lateral tooth-caps 1 tooth-caps 2 tooth-caps Supplied accessories 21088 21089 21096 21098 21093 21095 96 modules (9 mm) 48 modules (18 mm) Set of 40 21096 6 modules (9 mm) 3 modules (18 mm) Set of 12 0 0 - 21098 Set of 4 For 25 mm2 cable - - Comb busbars for C60 and iC60 Lateral tooth-caps Tooth-caps Insulated connectors 14886 14886 14887 14887 Set of 40 14888 14888 14888 14888 Set of 40 14885 14885 14885 14885 Set of 4 For 25 mm2 cable - - - DB123466 Comb busbar Catalogue numbers Characteristics 1-pole 2-pole 3-pole 4-pole Supplied accessories 14881 14891 14882 14892 14883 14893 14884 14894 b 24 modules (9 mm) b 48 modules (9 mm) b 12 modules (18 mm) b 24 modules (18 mm) b 1 piece b Set of 2 Rating: 80 A with 1 supply point 100 A with 2 supply points 2 lateral tooth-caps Comb busbars for C120 and NG125 Lateral tooth-caps + tooth-caps 054948d Comb busbar Catalogue numbers Characteristics 1-pole 2-pole 3-pole 4-pole Supplied accessories 82 14813 14811 14812 14814 b 45 modules (9 mm) b 48 modules (9 mm) b 22.5 modules (18 mm) b 24 modules (18 mm) b 1 piece b Set of 1 Rating: 125 A 63 A maxi by outgoers Tooth-caps (8 for 1 and 2-pole, 4 for 1 and 2-pole) 2 lateral tooth-caps 14818 14818 14818 14818 4 lateral tooth-caps + 20 tooth-caps - Functional system Earth blocks / neutral blocks Distribution Centralised distribution Earth blocks / neutral blocks 25 mm terminal block kit 4 x 6 mm2 terminal block kit Catalogue numbers Characteristics Permissible current Terminal block support kit Splitter block kit PRA90045 PRA90046 PRA90047 PRA90051 b Set of 2 b W = 2 blocks b Set of 5 b W = 1 blocks b Set of 10 b Set of 1 b W = 1 blocks b W = 34 blocks max. b Mounting on the functional uprights 160 A to 40 °C 90 A to 40 °C 63 A to 40 °C - PRA90048 PRA90050 DB107886 DB107887 DB107891 PB101639_32 DB107885 DB107884 DB107883 PB101638_68 2 DB107888 50 mm terminal block kit 2 PRA90049 b Set of 4 b Set of 1 b Set of 10 b W = 1 blocks b W = 8 blocks b W = 2 blocks b Designed to be clipped onto modular rail b Ui: 400 V - Uimp: 6 kV 90 A with 1 jonction 160 A with 2 jonctions in parallel Examples of composition E101371d E101372d E101373d 3-phase distribution block E101370d Used Catalogue numbers Single-phase distribution block E101369d Single-phase terminal block 90 A 1 x PRA90051 1 x PRA90045 2 x PRA90046 1 x PRA90050 160 A 1 x PRA90051 1 x PRA90045 2 x PRA90046 2 x PRA90050 80 A 2 x PRA90048 1 x PRA90045 2 x PRA90046 1 x PRA90050 125 A 2 x PRA90048 1 x PRA90045 2 x PRA90046 2 x PRA90050 160 A 3 x PRA90048 4 x PRA90045 3 x PRA90046 4 x PRA90050 83 Functional system Earth bars Distribution Centralised distribution Earth blocks with spring terminals Dd383501 Dd381560 Earth blocks with spring terminals to clip-on 04201 b Size: 12 x 3 mm b W = 330 mm b Equipped with a 35 mm² tunnel terminal (for earth blocks with spring terminals) Catalogue numbers Characteristics Dd381560 Bare earth bar They are installed: b In a duct, which may be a dedicated zone, totally separate from the devices b In the device compartment, at the top or bottom. Dd381560 Earth bars 04214 b 12 x 4 mm2 b Set of 4 b W = 75 mm 04215 b 3 x 16 mm2 b Set of 4 b W = 37 mm Earth bar with clamps DD381516 Earth bar with clamps 04200 b Earth bar with 40 clamps + one 35 mm² terminal b W = 450 mm Catalogue numbers Characteristics 04202 b 2 earth bars with 20 clamps + one 35 mm² terminal b W = 200 mm Dd383513 Neutral bars DD382529 Kit for neutral bar 04210 Insulating spacers to insert under an earth bar Catalogue number Description Accessories for top or bottom installation 84 On hexagonal spacers 04205 03005 04206 04207 04208 03185 Set of 2 supports Set of 2 supports H= H= 15 mm 45 mm Set of 2 brackets H= 80 mm H= H= H= 9 mm 23 mm 55 mm Set of four M5 hexagonal spacers In enclosure: earth bars W = 450 mm with clamps or spring terminals In duct: earth bar with clamps W = 200 mm DD383516 On fixing brackets DD383515 Used earth bars On 45° supports DD383514 Catalogue numbers Characteristics On rear of modular rail DD383512 Fixing mode 03186 03187 Functional system Distribution Earth bars Centralised distribution Accessories for installation on the side This solution saves considerable space in the device zone and avoids the need for the 300 mm wide duct. 2 fixing brackets for the earth bar on the functional uprights Dd383517 Fixing mode Catalogue numbers Characteristics Used earth bars 04206 04207 04208 H = 15 mm H = 45 mm H = 80 mm Set of 2 brackets Earth bar with clamps or spring terminals. Accessories for installation in duct On mounting plate for terminal block and earth bar Dd383495 Fixing mode Catalogue number Characteristics Used earth bars 04220 b A mounting plate (04220), made up of two supports, is equipped with: v a 1600 mm modular rail (04226) for terminal blocks v an earth bar The supports have cut-outs that can be used to easily tie down the connection wires. Earth bar with clamps or spring terminals. Accessories for installation on a dedicated mounting plate, in device compartment On mounting plate DD383488 Fixing mode Catalogue number Characteristics Used earth bars 04223 The mounting plate for terminal blocks (04223) can be equipped with two earth bars with clamps 200 mm earth bar with clamps. 85 Functional system Terminal blocks Distribution Centralised distribution Terminal block layout They can be installed: b In a duct, which may be a dedicated zone, totally separate from the devices b In the device compartment, at the top or bottom. Fast-connection terminal blocks 16 mm2 DD383821 10 mm2 DD383821 6 mm2 DD383820 4 mm2 DD383819 4 mm DD383818 Size of the conductor 2 Number of points 1 incomer, 1 outgoer 1 incomer, 2 outgoers 1 incomer, 1 outgoer 1 incomer, 1 outgoer 1 incomer, 1 outgoer Width 6 mm 6 mm 8 mm 10 mm 12 mm Catalogue 1 Terminal Grey numbers blocks and Blue quantity Green / Yellow 2 Separation partition 3 End Grey plate Blue AB1 RRN435U2GR 100 AB1 RRN435U2BL 100 AB1 RRNTP435U2 100 AB1 RRNTPAC442 10 AB1 RRNAC442GR 10 AB1 RRNAC442BL 10 AB1 RRAL42 10 4 2-pole insulated commoning link AB1 RRN435U3GR 100 AB1 RRN435U3BL 100 AB1 RRNTP435U3 100 AB1 RRNTPAC443 10 AB1 RRNAC443GR 10 AB1 RRNAC443BL 10 AB1 RRAL42 10 AB1 RRN635U2GR 50 AB1 RRN635U2BL 50 AB1 RRNTP635U2 50 AB1 RRNTPAC642 10 AB1 RRNAC643GR 10 AB1 RRNAC643BL 10 AB1 RRNAL62 10 AB1 RRN1035U2GR 50 AB1 RRN1035U2BL 50 AB1 RRNTP1035U2 50 AB1 RRNTPAC1042 10 AB1 RRNAC1042GR 10 AB1 RRNAC1042BL 10 AB1 RRAL102 10 AB1 RRN1635U2GR 50 AB1 RRN1635U2BL 50 AB1 RRNTP1635U2 50 AB1 RRNTPAC1642 10 AB1 RRNAC1642GR 10 AB1 RRNAC1642BL 10 AB1 RRAL162 10 Terminal blocks screw technology 35 mm2 70 mm2 150 mm2 501687_1R 501686_1R 501685_1R Size of the conductor Number of points 1 incomer, 1 outgoer 1 incomer, 1 outgoer 1 incomer, 1 outgoer Width 16 mm 24 mm 28 mm Catalogue 1 Terminal Grey numbers blocks and Blue quantity 2 2-pole insulated commoning link AB1 VVN3535U 20 AB1 VVN3535UBL 20 AB1 ALN352 10 (insulated) AB1 VVN7035U 20 AB1 VVN7035UBL 20 AB1 ALN702 10 (non-insulated) AB1 VVN15035U 10 AB1 VVN15035UBL 10 AB1 ALN1502 10 (non-insulated) Accessories for top or bottom installation Catalogue numbers Characteristics 86 03002 03004 b Depth adjustable modular rail b W = 432 mm b Rear modular b Set of 2 supports rail b Rail catalogue numbers 03004 b W = 432 mm ordered separately 03005 04206 On hexagonal spacers DD383506 On fixing brackets DD383505 On 45° supports DD383504 Directly on the functional uprights DD383503 Fixing mode 04207 04208 H= H= H= 15 mm 45 mm 80 mm b Set of 2 brackets b Rail catalogue numbers 03004 ordered separately 03195 H = 9 mm 03196 03197 H= H= 23 mm 55 mm b Set of four M6 hexagonal spacers b Rail catalogue numbers 03004 ordered separately Functional system Distribution Terminal blocks layout Centralised distribution Dd383500 Accessories for installation in the duct In a duct DD383502 Mounting 04220 b A mounting plate, made up of two supports can be equipped with: v a modular rail for the terminal blocks, that is 1600 mm long, can be cut to length and has 6.4 mm holes every 450 mm v an earth bar. b The supports have cut-outs that can be used to easily tie down the connection wires. Catalogue number Characteristics Accessories for installation on a dedicated mounting assembly This mounting assembly is used to easily install and connect a large number of terminal blocks in a minimum amount of space. It is particularly useful when a duct is not warranted or cannot be installed. In device compartment DD383507 Mounting Catalogue number Characteristics Markers DG113069 Catalogue numbers Characteristics Marking Blank 1 to 10 11 to 20 21 to 30 31 to 40 41 to 50 51 to 60 61 to 70 71 to 80 81 to 90 91 to 100 L1 L2 L3 + red – blue Clip-on Set of 25 04223 b Mounting brackets, fixed to the functional uprights at the top or bottom of the enclosure, is equipped with four 200 mm symetrical rails. They are installed vertically to facilitate cable running. b To facilitate mixing of different size terminal blocks and ensure convenient connections from the front or the side, the distance between rails and the depth of each rail can be adjusted. b The assembly has cut-outs that can be used to easily tie down the connection wires. b Earth bars, supplied separately, can be installed between the rows of terminal blocks to form different configurations, e.g.: v four sets of terminal blocks v 3 sets of terminal blocks + one or two earth bars (W = 290 mm). b The mounting assembly occupies a height of 250 mm, i.e. five 50 mm vertical modules. Accessories 6 mm pitch AB1 BV6 AB1 B610 AB1 B620 AB1 B630 AB1 B640 AB1 B650 AB1 B660 AB1 B670 AB1 B680 AB1 B690 AB1 B6100 AB1 B6L1 AB1 B6L2 AB1 B6L3 AB1 BV6RP AB1 BV6BM 8 mm pitch AB1 BV8 AB1 B810 AB1 B820 AB1 B830 AB1 B840 AB1 B850 AB1 B860 AB1 B870 AB1 B880 AB1 B890 AB1 B8100 - Label Stop plate AB1 S1 AB1 AB8P35 Clip-on 4.5 x 8.3 mm Set of 500 Screwable Set of 100 87 Prisma Plus G enclosures Prisma Plus G enclosures Contents IP30, IP31, IP43 enclosures ...................................... 91 Presentation .................................................................................91 Wall-mounted and floor standing enclosures ................................94 Combinations................................................................................96 Installation / lifting accessories......................................................97 Gland plates..................................................................................98 Accessories ..................................................................................99 Door accessories ........................................................................100 Spare-parts.................................................................................101 Dimensions.................................................................................104 IP55 enclosures........................................................ 107 Presentation ...............................................................................107 IP55 enclosures ..........................................................................110 Multiple combinations ................................................................. 111 Installation accessories...............................................................112 Wall-mounted enclosures IP55 gland plates ...............................113 Partial doors and functional units ................................................114 Side panels with cut-outs ............................................................115 Door accessories ........................................................................116 Spare-parts.................................................................................117 Dimensions.................................................................................118 89 Prisma Plus G enclosures IP30, IP31, IP43 enclosures Prisma Plus G enclosures IP30, IP31, IP43 enclosures Presentation For safe and upgradeable electrical switchboards > Safety of people and property > Continuity of service > Optimization and upgradeability > Ergonomics and complete accessibility > Controlled costs (installation, maintenance) and delivery times 100 % reliable and in compliance with existing standards All the components (switchgear, splitter blocks, prefabricated connections, etc.) have been designed to work together. All switchboard configurations have been tested. Optimized, upgradeable installation With Prisma Plus G, you can build the right switchboard for your customer, sized precisely to fit costs and needs. Thanks to the organization around functional units, the installation evolves simply while preserving its original performance. Ease of setup The complete accessibility of all mounting and connection points facilitates assembly and cabling in the workshop. The functional units are clearly identified: operations are intuitive and reliable, and connection and checking are performed naturally. 91 Prisma Plus G enclosures IP30, IP31, IP43 enclosures Commercial buildings: hotels, offices, shops, etc. Industry: technical room, etc. Presentation Surface mounting enclosures Enclosure delivered flat: total accessibility Designed for electrical continuity b 160 A b IP30 b IK07/08 Gland plate PD390300 b Dismountable and cuttable Quick fastening on hook-on rail b Easy wall mounting Safety b Powerclip busbars, IPxxB, pre-fitted Ergonomic handle Quick-connect terminal blocks Fast operation and easy maintenance Ergonomics and safety b Easy front plate handling thanks to the ergonomic gripper b Legible "Open/closed" positions of front plate b Integrated front plate sealing function PD390240 b Straightforward organization in functional units Continuity of service b Direct accessibility of functional unit thanks to the front plate hinges kit b Total accessibility of switchgear thanks to the installation of hinges on all front plate (allows the front panel to be made swivelling) Main characteristics Steel sheet metal with electrophoresis treatment + hot-polymerised polyester epoxy powder. Enclosure: b width: 600 mm, with duct: 300 mm b height: 330 to 1380 mm, b depth: 205 mm without door / 250 mm with door. Designation G IP30 - IP31 - IP43 enclosure Rated operational current Color Standards conformity Degree of protection Easy design with Rapsody software > see page 25 Degree of protection against mechanical impacts Isolation Doors Mounting 630 A - Icc = 50 kA White colour RAL 9001 EN 62208, IEC 61439-2 IP30 with or without door, IP31 with canopy + door, IP43 with canopy + door + gasket IK08 with door, IK07 without door Class 1 b Plain or transparent, opening to right or left b By design, electrical continuity of moving parts (hinges…) b Supplied with a handle and keylock (key 405) Distance behind door = 58 mm (possibility of push-buttons, lamps installation). Surface mounting, floor standing, flush mounting via a kit > see page 97 93 Wall-mounted and floor standing enclosures Prisma Plus G enclosures IP30, IP31, IP43 enclosures IP30 630 A enclosures Reversible doors (opening to left or right), equipped with a handle and keylock (key 405). Ducts, width 300 mm No. of vertical modules of 50 mm 6 9 12 15 18 21 24 27 DD380627 DD380626 DD382928 DD380624 DD380623 DD380622 DD380618 DD382927 Wall-mounted enclosures, width 600 mm Height in mm Enclosure Plain door Transparent door No. of vertical Height modules of in mm 50 mm Rear + top and bottom plates (1) Plain door Transparent door 330 480 630 780 930 1080 1230 1380 08102 08103 08104 08105 08106 08107 08108 08109 08122 08123 08124 08125 08126 08127 08128 08222 08132 08133 08134 08135 08136 08137 08138 08232 6 9 12 15 18 21 24 27 08172 08173 08174 08175 08176 08177 08178 08179 08182 08183 08184 08185 08186 08187 08188 08282 08197 08198 08292 330 480 630 780 930 1080 1230 1380 (1) Supplied with a combination kit for enclosure + duct association. Floor standing enclosures IP30 Reversible doors (opening to left or right), equipped with a handle and keylock (key 405). b two basic floor standing enclosures cannot be combined; b to create a switchboard comprising a number of enclosures, use a basic floor standing enclosure and one or more floor-standing enclosure extensions; b floor standing enclosure extensions are supplied with a combination kit for the basic floor standing enclosure; b cables can be run on the sides of the plinth (diameter y 140 mm). Partitionning > see page 59 94 Height Basic Plain in mm enclosure door 1530 1680 1830 08202 08203 08204 08222 08223 08224 Transparent door 08232 08233 08234 No. of vertical modules of 50 mm 27 30 33 Height in mm Rear Plain door 1530 1680 1830 08212 08222 08213 08223 08214 08224 Dd380640 Transparent door Rear + top and bottom plates Plain door 08232 08233 08234 08272 08273 08274 08282 08292 08283 08293 08284 08294 Spare parts (rear accessories, door accessories, sides, uprights, etc. ) > see page 101 Dd380639 Dd380638 Dd380637 Dd380636 Dd380635 Dd380636 Dd380636 Dd380634 No. of vertical modules of 50 mm 27 30 33 Enclosure extensions, Ducts, width 300 mm width 600 mm Dd381354 Dd380631 Floor standing enclosures, width 600 mm Transparent door Prisma Plus G enclosures IP30, IP31, IP43 enclosures Wall-mounted and floor standing enclosures Accessories to increase the degree of protection IP Used with Catalogue numbers Designation Dd381268 Gasket for the door to increase the IP value from IP31 to IP43 Dd381257 Canopy to increase the IP value from IP30 to IP31 1 wall mounted enclosure 1 wall mounted enclosure + 1 duct (1) 2 wall mounted enclosures 2 wall mounted enclosures + 1 duct (1) 1 wallmounted enclosure + 2 ducts (2) Enclosures or a duct from 6 to 33 modules 08830 08832 08831 08833 08827 08841 The addition of a canopy over a wall-mounted or floor standing enclosure equipped with When the switchboard is equipped with a canopy, a door ensures compliance with the degree of protection IP31. a gasket for the doors ensures compliance with the degree of protection IP43. L = 5.3 m (1) Whatever the duct position. (2) Ducts on the sides. No. of vertical modules of 50 mm 6 9 12 15 18 21 24 27 Dd380627 Dd380626 Dd383030 Dd382928 Dd383028 Wall-mounted enclosures, width 300 mm Height in mm Rear + top and bottom plates Side panels Plain door Transparent door 330 480 630 780 930 1080 1230 1380 08172 08173 08174 08175 08176 08177 08178 08179 2 x 01040 2 x 01041 2 x 01042 2 x 01043 2 x 01044 2 x 01045 2 x 01046 2 x 01035 08182 08183 08184 08185 08186 08187 08188 08282 08197 08198 08292 No. of vertical modules of 50 mm 27 30 33 Dd380640 Dd380639 Dd383030 Dd380631 Dd380631 Floor standing enclosures, width 300 mm Height in mm Rear + top and bottom plates Side panels Plain door Transparent door 1530 1680 1830 08272 08273 08274 2 x 01035 2 x 01034 2 x 01033 08282 08283 08284 08292 08293 08294 Spare parts (rear accessories, door accessories, sides, uprights, plinths, etc.) > see page 101 95 Prisma Plus G enclosures IP30, IP31, IP43 enclosures Combinations Multiple combinations To make the combination more rigid, particularly during transport, it is mandatory to use a set of cross-members secured to the rear of the switchboard. Combination kits Horizontal 1 wall-mounted enclosure + 1 duct Set of two lifting/reinforcement 08812 cross-members or vertical uprights + combination kit (2) - 1 wall-mounted enclosure + 2 ducts 08811 2 wall-mounted enclosures 08811 2 wall-mounted enclosures + 1 duct 08813 2 wall-mounted enclosures + 2 ducts 08814 2 wall-mounted enclosures + 3 ducts 08826 2 wall-mounted enclosures 08817 (1) - 08816 08816 08816 08816 08816 1 floor standing enclosure + 2 ducts 1 floor standing enclosure + 1 enclosure extension 08811 1 floor standing enclosure + 2 ducts + 1 enclosure extension 08814 1 wall-mounted enclosure + 3 ducts + 1 enclosure extension 08826 1 floor standing enclosure + 1 wall-mounted enclosure 08811 1 floor standing enclosure + 1 duct + 1 enclosure extension 08813 08817 (1) - - - - - 08816 - - - - - 08882 4 wall-mounted enclosures 4 wall-mounted enclosures + 4 ducts 08814 4 wall-mounted enclosures + 6 ducts 08826 2 additional ducts 08811 4 wall-mounted enclosures + 2 ducts 08813 2 additional wall-mounted enclosures must be made 08817 08816 08817 08816 08817 08816 08817 08816 2 supplied with the ducts 2 supplied with the enclosure extensions 08818 08818 2 x 08818 3 x 08818 4 x 08818 08818 08818 1 floor standing enclosure + 1 wall-mounted enclosure + 2 ducts 1 floor standing enclosure + 1 enclosure extension + 2 wall-mounted enclosures 08811 1 floor standing enclosure + 1 enclosure extension + 2 ducts + 2 wall-mounted enclosures 08813 1 floor standing enclosure + 1 enclosure extension + 4 ducts + 2 wall-mounted enclosures 08814 1 floor standing 2 more ducts enclosure + 1 enclosure extension + 6 ducts + 2 wall-mounted enclosures 08826 must be made must be made 08817 08815 08817 - 08817 - 08817 - - - 08818 2 x 08882 2 x 08818 2 x 08882 3 x 08818 2 x 08882 4 x 08818 2 x 08882 08818 - 08818 08882 DD384000 For wall-mounted enclosure Vertical DD384000 For floor standing enclosure 1 floor standing enclosure + 1 duct Set of two lifting/reinforcement 08812 cross-members or vertical uprights + combination kit (2) - + plain plate Combination kits - Multiple DD384000 For wall-mounted enclosures 2 wall-mounted enclosures + 2 ducts Set of two lifting/reinforcement 08812 cross-members Set of two vertical uprights (1) 08817 + combination kit (2) 08816 DB124228 + multiple combination kit must be made For floor standing enclosure DD384000 Set of two lifting/reinforcement 08812 cross-members Set of two vertical uprights 08817 + combination kit (2) 08815 2 floor standing enclosures + 2 additional wall-mounted enclosures + multiple combination kit + plain plate 08818 08882 (1) Note: for more than 33 combined modules, these vertical uprights are mandatory. (2) A combination kit is supplied with each duct or enclosure extension. It can be necessary to use one kit more than those already supplied. 96 Prisma Plus G enclosures IP30, IP31, IP43 enclosures Installation / lifting accessories Lifting accessories The lifting rings are used to move a single wall-mounted or floor standing enclosure. For combined enclosures, use the lifting/reinforcement cross-members (see below). Catalogue numbers Characteristics Lifting/reinforcement cross-members for combined enclosures DD381653 DD384010 2 lifting rings for single wall-mounted or floor standing enclosures 08801 08812 08811 08811 08813 08814 Set of two lifting rings Have 2 types of holes: for lifting and for mounting on a wall 08826 Installation possibilities Switchboards can be mounted on a wall in three manners: with the hook-on rail system, via the inside of the enclosure or using external wall-mounted brackets. Combined enclosures can be mounted using the lifting/reinforcement crossmembers set of two lifting/reinforcement cross-members. DD384038 Delivered with the enclosure The enclosure comes with 2 cross-members secured to the back of the enclosure (top and bottom) and a support rail (with levelling adjustment) for screw mounting on the wall. The enclosure is easily mounted on the hook-on rail system. 08804 The enclosure can be mounted through 4 external wall-mounted brackets. the spacers in the 4 holes provided on the enclosure using using 8 mm diameter screws (2 knockouts can be removed if necessary to provide 2 other holes). Plinth raiser Dd380633 For floor standing enclosure Catalogue numbers Characteristics 08805 For basic floor standing enclosure or extension 08807 For a duct Flush-mounting kit For wall-mounted enclosure Dd381256 Catalogue numbers Characteristics Mounting using the external wall-mounted brackets DD384037 Mounting via the inside DD384036 Hook-on rail system Catalogue numbers Characteristics 08819 6 to 18 modules 08820 21 to 27 modules 97 Prisma Plus G enclosures IP30, IP31, IP43 enclosures Gland plates G gland plates Enclosures (wall-mounted, floor standing, ducts) are supplied with a plastic gland plate installed on the top or bottom for wall-mounted enclosures and the top for floor standing enclosures. For some connections needs, the existing plastic gland plate can be replaced by this metal gland plate. Used with Cat. no. Dd380861 Metal plates with cut-outs + plastic gland plates Dd382817 Plain metal gland plates At the top or bottom of a wall-mounted enclos. or duct, at the top of a floor standing enclos. Wall-mounted or floor standing enclos. Duct 08870 08874 Used with Using at the top or bottom of a wall-mounted enclosure (+ duct) at he top of a floor standing enclosure (+ duct) Wall-mounted or floor standing enclosure. Duct 08880 08884 Catalogue numbers FL21 cut-out metal plates Metal plate with cut-outs This plastic gland plate can be replaced by an interface plate with cut-outs for special cable entry systems made of an insulating material (plain, with knockouts or membrane-type). Trunking spreader Metal plate with cut-outs Dd381636 Dd382933 Trunking spreader Wall-mounted or floor standing enclosure 08871 Duct 08875 Metal gland plates for plinth Used with Catalogue numbers DB124235 DB124234 Cat. no. 08824 Characteristics For a professional-looking connection between the trunking and the enclosure. Can be installed at the top or bottom. The spreader is marked for cut-outs for standard trunking sizes. The maximum capacity is two 250 x 80 mm trunking sections. Used with Catalogue numbers Between the plinth and the bottom of a floor standing enclosure or duct, for ensuring IP20 Floor standing enclosure Duct 08887 08888 FL21 gland plates, plain with knockouts or membrane-type The gland plates are easy to install using the mounting kit (supplied with each gland plate) that positions and holds the nuts during installation. This makes it possible to mount the gland plates using a single tool. 08892 2 2 08895 5 8 - Number of entries - 12 4 13 From 5 to 7 mm dia. From 6 to 10 mm dia. From 7 to 12 mm dia. From 8 to 12 mm dia. From 10 to 14 mm dia. From 12 to 18 mm dia. From 14 to 20 mm dia. From 17 to 32 mm dia. From 20 to 26 mm dia. From 28 to 60 mm dia. Dd382936 08891 4 4 4 - Dd382936 08881 - Dd382936 Dd382935 Membrane-type Catalogue numbers M12 M12 or M20 M16 or M25 M20 M20 or M32 M25 or M40 98 Dd382935 With knockouts Dd382935 Plain Dd382934 Gland plates 08872 4 4 12 4 1 25 08896 2 6 8 16 2 1 35 08897 2 2 Partial doors Type Plain door Partial door with cut-outs (for 72 x 72 or 96 x 96 mm devices) Catalogue numbers Characteristics Dd381636 IP30, IP31, IP43 enclosures Accessories Dd381636 Prisma Plus G enclosures 08850 08851 Height: 6 modules. Useful height behind a partial door: 5 modules. Installation on a wall-mounted enclosure at least 12 modules high (H u 630 mm). Reversible (opening to left or right), equipped with a handle and keylock (key 405). Note: each wall-mounted enclosure and basic floor standing enclosure or extension can be equipped with only one partial door. The front must be completed with another door. Partitionning > see page 59 Canopy - Gasket > see page 95 99 Door accessories Prisma Plus G enclosures IP30, IP31, IP43 enclosures Door handles and padlocking DD383885 Padlocking DD383883 Standard handle DD383882 Catalogue numbers Characteristics ASSA/ABLOY handle DD383881 EURO handle 08932 Supplied without barrel 08933 Supplied without barrel 08931 Supplied with barrel lock (key no. 405) RAL 7016 08938 The kit can be installed on the door handles equipped with any of the barrel locks and inserts above Barrel locks, inserts The barrel locks and inserts below can be mounted on handle 08931 and on all the door handles of the Prisma Plus G IP30. DD381203 08940 1 key no. 405 08941 2 keys no. 455 08942 2 keys no. 1242E DD383884 DD383884 Catalogue numbers Characteristics DD383884 Barrel locks 08943 2 keys no. 3113A 08944 2 keys no. 2433A 08956 2 keys no.2432E 08945 08946 DIN double bar insert Screwdriver slot insert 08947 08948 08949 Male triangle insert 6.5 mm 7 mm 8 mm 08950 9 mm DD383884 Catalogue numbers Characteristics DD383884 DD383884 Inserts 08951 08952 08953 Male square insert 6 mm 7 mm 8 mm 08955 Female square insert 6 mm Earthing braid The earthing braid is used to earth a door or partial door with devices. DD384005 08911 Equipped with a 5 mm diameter lug at one end and a 6 mm diameter lug on the other DD384052 08910 Equipped with a 4 mm diameter lug at one end and a 6 mm diameter lug on the other DD381338 Catalogue numbers Characteristics Earthing wire, 6 mm2 DD384005 Earthing braid, 6 mm 2 Finishing parts > see page 63 100 Prisma Plus G enclosures IP30, IP31, IP43 enclosures Spare-parts Accessories (IP30) Duct accessories 01036 DD384483 4 kit pillars + pillar heads 1 earthing braid plug 4 washers 2 combination uprights 2 short combination crossbars 2 base blanking plugs 2 association fasteners 4 spacers 2 screws with flange 1 self threading screw 2 A-angle parts 2 B-angle parts 7 nuts HX grooved Wall-mounted and floor standing enclosure accessories 01018 DD384484 4 kit pillars + pillar head 2 A-angle parts 2 B-angle parts 8 self threading screws 1 earthing braid plug 4 base blanking plugs 4 spacers DD384485 4 nuts HX grooved 4 spacers 01098 Accessory for closing, wall-mounted and floor standing enclosure 01032 DD384486 Door accessories (IP30) 1 earthing braid plug 2 door stops 3 self threading screws M5 x 10 1 handle staple 1 handle 1 square rod 3 fixed hinges 3 hinge pins 3 stop bolt 4 self threading screws M5 x 17 DD384487 Retrofit handle 01220 1 handle 1 key no.405 1 handle staple 1 Pack kit pin 1 assembled rod angle 1 peg and angle assembly for G cubicle 1 pozidriv screw for handle staple 1 self threading screw for Pack enclosure 1 pozidriv screw for wall-mounted and floor standinbg enclosures 101 Prisma Plus G enclosures IP30, IP31, IP43 enclosures Spare-parts DD384490 DD384488 Gland plates (IP30) Plain bottom gland plate 01017 Duct bottom plate 01039 DD384491 Side (IP30) Wall-mounted enclosures Side for 6-module wall-mounted enclosures 01040 Side for 9-module wall-mounted enclosures 01041 Side for 12-module wall-mounted enclosures 01042 Side for 15-module wall-mounted enclosures 01043 Side for 18-module wall-mounted enclosures 01044 Side for 21-module wall-mounted enclosures 01045 Side for 24-module wall-mounted enclosures 01046 Floor standing enclosures Side for 27-module floor standing enclosures 01035 Side for 30-module floor standing enclosures 01034 Side for 33-module floor standing enclosures 01033 Floor standing enclosures Side for 27-module floor standing enclosures 01030 Side for 30-module floor standing enclosures 01029 Side for 33-module floor standing enclosures 01028 DD384492 Central uprights (IP30) Plinths (IP30) DD384493 Floor standing enclosures 01050 Left drilled base bracket + Right drilled base bracket 4 self threading screws DD384494 Accessories for plinth 01051 Left base bracket + Right base bracket 4 self threading screws DD384495 Plinth front, 600 mm 01052 Base cover + plinth 2 self threading screws Plinth front, 300 mm DD384496 Base cover + plinth 2 self threading screws 102 01053 Prisma Plus G enclosures IP30, IP31, IP43 enclosures DD384500 Front cover support uprights (IP30) Spare-parts 2 front cover support uprights - 6 modules 01250 2 front cover support uprights - 9 modules 01251 2 front cover support uprights - 12 modules 01252 2 front cover support uprights - 15 modules 01253 2 front cover support uprights - 18 modules 01254 2 front cover support uprights - 21 modules 01255 2 front cover support uprights - 24 modules 01256 2 front cover support uprights - 27 modules 01257 2 front cover support uprights - 30 modules 01258 2 front cover support uprights - 33 modules 01259 DD384501 20 front-plate locking handles with sticker 01093 DD384502 Front-plate accessories 10 sets of front-plate locking handles 01094 Accessories Powerclip 160/400 A 01210 DD384503 Powerclip busbar accessories (IP30) 2 extremity obturators 2 brackets 2 screws Accessories Powerclip 630 A 01211 2 extremity obturators 2 metallic supports 2 brackets for support 2 hexagonal spacers DD384504 8 self threading screws 2 IPxxB clipon cover Powerclip 01201 103 Dimensions Wall-mounted enclosures Floor standing enclosures Floor standing enclosures H1 6 9 12 15 18 21 24 27 27 30 33 330 480 630 780 930 1080 1230 1380 1530 1680 1830 - - - - - - - - 1380 1530 1680 DD384040 H DD383050 No. of vertical modules DD383049 Wall-mounted enclosures DD384044 Dd381897 DD384039 IP30, IP31, IP43 enclosures DD381914 Prisma Plus G enclosures DD383052 DD383826 DD384045 DD384041 Ducts 147 104 Prisma Plus G enclosures Dimensions Cable entry Trunking spreader DD383841 DD383841 IP30, IP31, IP43 enclosures 157 496 206 Wall-mounted installation Ducts 545 483 Wall-mounted enclosures DD384043 255 193 DD384317 DD384318 Wall-mounted and floor standing enclosures Ø9 Floor standing enclosures Ø9 No. of vertical modules H1 H2 6 9 12 15 18 21 24 27 27 30 33 246 396 546 696 846 996 1146 1296 1488 1638 1788 430 580 730 880 1030 1180 1330 1480 1580 1730 1880 DD383062 Floor standing plinth fixation Depth behind front plate Dd383061 Adjustable rail Cat. no. 03002 or 03011 Dd383059 Fixed rail Cat. no. 03001 or 03010 Slotted mounting plate Recessed mounting plate Cat. no. 03171, 03172, 03173, 03176, 03177 or 03178 Dd383061 Dd383056 Dd383057 Modular rail Dd383058 Dd383055 Functional uprights 0 Recessed rail Cat. no. 03003 Rear rail Cat. no. 03004 Flat plate Cat. no. 03170 or 03175 105 Prisma Plus G enclosures IP55 enclosures Prisma Plus G enclosures IP55 enclosures Presentation Great capability for meeting the requirements of your installation > Safety of people and property > Continuity of service > Robustness > Ergonomics and complete accessibility > Optimization and upgradeability 100 % reliable and in compliance with existing standards All the components (switchgear, splitter blocks, prefabricated connections, etc.) have been designed to work together. All switchboard configurations have been tested. Even the most demanding. Optimized, upgradeable installation Prisma Plus G IP55 is the only switchboard in this category designed as a "kit". All configurations and combinations are possible, with full access. Thanks to the organization around functional units, the installation evolves simply while preserving its original performance. Ease of setup The complete accessibility of all mounting and connection points facilitates assembly and cabling in the workshop. The functional units are clearly identified: operations are intuitive and reliable, and connection and checking are performed naturally. 107 Prisma Plus G enclosures Presentation IP55 enclosures Weatherproof enclosures Metallic indoor enclosures to compose Severe environments: industrial and agricultural buildings, basements, kitchens, etc. Enclosure delivered flat: total accessibility Designed for electrical continuity b 630 A b IP55 b IK10 b Functionalized installation of push buttons, power sockets, etc. b Installation of power sockets on the side PE60330 Practical Ergonomics and safety b Easy panel handling thanks to the ergonomic gripper b Legible "Open/closed" positions of front plate, b Integrated front plate sealing function Continuity of service b Direct accessibility of functional unit if front plates are equiped with hinges Wide range of combination possibilities Numerous installation possibilities b Vertical, horizontal with duct, etc. b Direct installation on: self-supporting structure, pole-mounted, wall mounted Weaterproofing PE60331 b Broad choice of IP55 gland plates Main characteristics Steel sheet metal with electrophoresis treatment + hot-polymerised polyester epoxy powder. Enclosure: b width: 575 mm, with duct: 325 mm b height: 450 to 1750 mm, b depth: 260 mm with door. Delivered with earthing braid (with door). Description IP55 enclosure Easy design with Rapsody software > see page 25 Rated operational current Color Standards conformity Degree of protection Degree of protection against mechanical impacts Isolation Doors Earthing Combination 630 A - Icc = 50 kA White colour RAL 9001 EN 62208, IEC 61439-2 IP55 with door IK10 Class 1 b Plain or transparent, opening to right or left b By design, electrical continuity of moving parts (hinges…) b Supplied with a handle and keylock (key 405) Distance behind plain door = 78 mm, Distance behind transparent door = 73 mm Earthing braid delivered with enclosure > see page 111 109 IP55 enclosures Prisma Plus G enclosures IP55 enclosures Enclosures and doors Reversible doors (opening to left or right), equipped with a handle and keylock (key 405). 450 650 850 1050 1250 1450 1750 08302 08303 08304 08305 08306 08307 08309 08322 08323 08324 08325 08326 08327 08329 08332 08333 08334 08335 08336 08337 08339 Height in mm 450 650 850 1050 1250 1450 1750 Rear + plain door 08342 08343 08344 08345 08346 08347 08349 Dd381523 Dd381522 Dd381526 Top and bottom plates for side-by-side combination 08371 08371 08371 08371 08371 08371 08371 Side panels for vertical combination Frame + plain door Frame + transparent door 08352 08353 08354 08355 08356 08357 08359 08322 08323 08324 08325 08326 08327 08329 08332 08333 08334 08335 08336 08337 08339 Top and bottom plates 08372 08372 08372 08372 08372 08372 08372 Rear + plain door 08342 08343 08344 08345 08346 08347 08349 Top and bottom plates 08372 08372 08372 08372 08372 08372 08372 Dd383032 Wall-mounted enclosures, width 300 mm Dd381528 Dd381527 Ducts, width 300 mm 08312 08313 08314 08315 08316 08317 08319 Dd381525 Dd381524 Frame + plain Frame Rear door + transparent door Type No. of vertical modules of 50 mm 7 11 15 19 23 27 33 Dd381523 Basic enclosure Dd381527 7 11 15 19 23 27 33 Extension enclosures, width 600 mm Height in mm Dd381528 No. of vertical modules of 50 mm Dd381522 Basic enclosure, width 600 mm Dd381521 Type Side panels 2 struts 08352 08353 08354 08355 08356 08357 08359 2 x 01025 2 x 01025 2 x 01025 2 x 01025 2 x 01025 2 x 01025 2 x 01025 Spare parts > see page 117 Dimensions > see page 118 Canopy For enclosure For duct DB404577 Using Catalogue numbers Characteristics Dimensions > see page 118 Partitioning > see page 59 110 08386 08387 b Installed on the mounting uprights or directly on the wall, canopies improve switchboard protection against vertically falling water and objects. b Colour: RAL 7016. b Supplied with: v the hardware required for mounting on the uprights v the components required for combination with another canopy. Prisma Plus G enclosures IP55 enclosures Multiple combinations Combination kits Catalogue numbers Catalogue numbers Characteristics Horizontal/vertical combination kit "L" combination kit Square combination kit Single pillar Mounting upright 08381 2 double pillars 08382 1 triple pillar + 1 single pillar 08383 1 quadruple pillar Supplied with basic enclosures 08391 L = 1950 mm Mounting example Wall-mounted enclosures Dd381436 In square DB404572 In L Dd381434 Simple 1 Basic enclosure 1 1 basic enclosure 1 1 basic enclosure 2 Rear plate for enclosure extension 2 1 rear + door for duct 3 Rear plate for enclosure extension 3 1 set of two top and bottom plates for duct 2 3 rear plates for enclosure extensions 4 1 rear plate for enclosure extension 5 1 set of two side panels Combination kits 4 1 horizontal/vertical combination kit 08381 6 1 "L" combination kit 08382 7 1 horizontal/vertical combination kit 08381 Mounting uprights - - 3 1 set of two top and bottom plates for enclosure extensions 4 1 set of two side panels 5 1 square combination kit 08383 6 2 horizontal/vertical combination kits 2 x 08381 7 3 mounting uprights W = 1950 mm (to reinforce the switchboard) 3 x 08391 Note: for combinations of more than two enclosures, the switchboard must be reinforced using mounting uprights (08391). Lifting Dd381455 Lifting rings Catalogue number Characteristics 08396 Set of two. Supplied with mounting hardware. The lifting rings are secured directly to the switchboard or to the mounting uprights. 111 Installation accessories Prisma Plus G enclosures IP55 enclosures Mounting supports Catalogue numbers Catalogue numbers Characteristics Quantity to order Mounting uprights Plinth gusset 08391 b W = 1950 mm b Colour: RAL 7016 b Supplied with: v two adjustable fixing brackets, v one joint for combination with a plinth or another upright. Leave space behind the switchboard for cable running and to improve ventilation. For one enclosure, order two uprights. For each enclosure extension or duct, order one additional upright. 08392 b H = 150 mm b Colour: RAL 7016 Plinth cover panel (for enclosure) 08393 b L = 600 mm b Colour: RAL 7016 Plinth cover panel (for duct) 08394 b L = 300 mm b Colour: RAL 7016 For the basic enclosure, order two gussets and one 600 mm wide plinth cover panel. For each enclosure extension or duct, order one additional gusset and the corresponding cover panel. Mounting example Designation Remarks 3 x 08392 + 08393 + 08394 Free-standing structure DB404576 08391 On wall structure DB404575 DB404574 Catalogue numbers On plinth DB404573 On uprights 3 x 08391 + 3 x 08392 + 08393 + 08394 3 gussets 3 uprights + 3 gussets + 1 plinth cover panel for enclosure + 1 plinth cover panel for enclosure + 1 plinth cover panel for duct + 1 plinth cover panel for duct 4 x 08391 + 4 x 08392 + 2 x 08393 3 mounting uprights 4 uprights + 4 gussets + 2 plinth cover panels for enclosure The uprights are used to The plinth, installed in the factory The switchboard can be mounted The free-standing structure is mount on a wall one or or on-site, raises the switchboard on the structure in the factory or on simply two wall structures more enclosures combined to protect it and facilitate spreading site. combined back-to-back. horizontally or vertically. of cables arriving from a trough. Two wall-fixing brackets supplied The switchboard can be The wall-fixing brackets supplied with the basic enclosure ensure positioned anywhere. with the plinth ensure that the that the switchboard cannot topple It can be fixed to the floor and switchboard cannot topple over. over. moved easily using the lifting rings (08396). It can be equipped with one or more enclosures with Schneider sockets. Mounting on a pole DD381450 2 reinforcement cross-members to support the enclosure Catalogue number Characteristics 112 08395 The kit is used to mount an enclosure or an enclosure + duct combination, without drilling, to an I-beam or concrete pole that can be rectangular or cylindrical. The maximum circumference of the pole is 580 mm. Supplied with mounting hardware. Wall-mounted enclosures IP55 gland plates Prisma Plus G enclosures IP55 enclosures Gland plates Enclosures are supplied with metal gland plates installed on the top or bottom panel of the enclosures (2 plates) or 300 mm wide ducts (1 plate). These plates can be replaced by metal plates with cut-outs for special cable entry systems made of an insulating material (plain, with knockouts or membrane-type). They are designed for entry of cables of different cross-sectional areas via the bottom of a switchboard while maintaining the IP55 degree of protection. The gland plates are easy to install using the mounting kit (supplied with each gland plate) that positions and holds the nuts during installation. This makes it possible to mount the gland plates using a single tool. DD383827 Metal plate with cut-outs 08876 08891 4 4 4 12 08892 2 2 4 08895 5 8 13 DB124230 DD383829 08881 - Other gland plates DD383829 DD383829 08898 39 x 7 to 26 mm diameter entries 08899 2 x 33 to 72 mm diameter entries 39 2 Catalogue numbers From 5 to 7 mm cable diameters From 6 to 10 mm cable diameters From 7 to 12 mm cable diameters From 8 to 12 mm cable diameters From 10 to 14 mm cable diameters From 12 to 18 mm cable diameters From 14 to 20 mm cable diameters From 17 to 32 mm cable diameters From 20 to 26 mm cable diameters From 28 to 60 mm cable diameters Number of entries 08872 4 4 12 4 1 25 08896 2 6 8 16 2 1 35 DD383830 DD383830 FL21 membrane-type gland plates DD383830 Catalogue numbers M12 M12 or M20 M16 or M25 M20 M20 or M32 M25 or M40 Number of entries DD383828 FL21 plain gland plates and gland plates with knockouts DB124229 Catalogue number 08897 2 2 Spare parts (FL21 gland plate for Pack enclosures) > see page 117 Dimensions > see page 119 113 Partial doors and functional units for partial door Prisma Plus G enclosures IP55 enclosures Partial doors 4 modules (H = 200 mm) for enclosure from 11 to 27 modules 6 modules (H = 300 mm) for enclosure at least 33 modules high Installation With cut-outs DD381438 Plain DD382674 Type 08374 08376 08375 08377 b On a wall-mounted enclosure at least 11 modules high (H = 650 mm). b The front must be completed with another door (plain or transparent). b Each enclosure or extension can be equipped with only one partial door. b Designed for two mounting plates with 22 mm diameter devices or Schneider Electric industrial sockets. b They are supplied with an insulating plain mounting plate that can be used to: v blank off a reserve hole, v install all types of devices (sockets, EPO devices, measurement devices). b The dimensions of the two holes are 200 mm x 112 mm. b Hinges that open 170° b Equipped with a 8 mm male triangle insert (key not supplied). Characteristics Functional units for partial doors They can be installed: b horizontally on the partial doors with cut-outs b horizontally vertically at any point on a door or side panel. 114 For industrial sockets 08862 b For installation of eight 22 mm diameter devices (lights, switches, pushbuttons, etc.) b Supplied with 4 blanking plug 08863 b With two 65 x 85 mm holes b Intended for the installation of: v 10/16 A residential sockets v flush-mount 16 A LV sockets, inclined or straight, IP44/IP67 08864 b Intended for the installation of: v residential sockets (< 10 /16 A) in the 65 x 85 mm hole (1a) v flush-mount inclined or straight 16 A LV sockets, IP44/ IP67, IK08, in the 65 x 85 mm hole (1b) v inclined 16 and 32 A IP44 and IP67 sockets in the 90 x 100 mm hole (1) DD381444 08861 b Can be used to: v blank off partial doors with cut-outs v mount any type of device (EPO devices, measurement devices, sockets) DD381443 DB404553 For 22 mm diameter devices DD381442 Catalogue numbers Characteristics Plain DB404552 Type Prisma Plus G enclosures IP55 enclosures Side panels with cut-outs Side panels with cut-outs These panels are designed to replace the standard side panel. They can be mounted on the left or right-hand side. DB404578 Side panels with cut-out No. of vertical modules of 50 mm 7 11 15 19 23 27 33 Height in mm 450 650 850 1050 1250 1450 1750 No. of 103 x 255 mm holes 1 2 2 2 2 2 2 Catalogue numbers 08362 08363 08364 08365 08366 08367 08369 The cut-outs are designed for the installation of Pratika PK industrial sockets up to 63 A either directly or on 103 x 225 mm adaptation plates of the Kaedra enclosure range. Installation is direct (in 103 x 225 mm cut-outs) for: b 16/32 A interlocked LV sockets, IP44/IP65, IK08 b 16 A VLV sockets with safety transformers, IP44/IP65, IK08. DD382841 DD382841 Functional units catalogue numbers DD382839 Size for industrial sockets DD382842 Industrial sockets and functional units DD382840 Industrial sockets and functional units 103 x 225 mm b 16/32 A interlocked LV sockets b 16 A VLV sockets with safety transformers 103 x 225 mm b 16 A and 32 A LV b VLV sockets b RJ45 sockets b 63 A LV sockets b 16 or 32 A VLV sockets (after uncapping of the opening) b blanking plate 65 x 85 mm + 90 x 100 mm 13142 100 x 107 mm 65 x 65 mm - 13144 13143 13143 Direct installation 115 Door accessories Prisma Plus G enclosures IP55 enclosures Locks b The small plain and transparent doors (7 to 23 modules) are supplied with a small handle comprising a barrel lock no. 405. b The large plain and transparent doors (27 to 33 modules) are supplied with a large handle comprising a barrel lock no. 405. b The partial doors are supplied with an 8 mm male triangle insert. b All doors can receive as optional equipment: v a large or small handle with a barrel lock no. 405. The latter can be replaced by other barrel locks or special inserts v a large EURO handle, supplied without a barrel lock v door inserts (squares, triangles, double bars, screwdriver slots). Handles for replacement Dd380704 Dd380704 Handles Catalogue numbers 08936 Designation Door latch with lock and 2 no. 405 keys 08935 08934 Handle (W = 155 mm) EURO handle without with lock and a barrel lock (1) 2 no. 405 keys (1) Do not suit to barrels with an automatic return stroke of the key. Padlocking Dd380706 Padlocking 08939 The kit can be installed on all IP55 doors, except those equipped with an EURO lock. Kit designed for three padlocks. Catalogue number Designation Handle barrel locks and inserts These components may equip handles after removing the standard barrel lock no. 405. Supplied with Catalogue numbers Dd380706 Dd380706 Dd380706 Dd380706 Dd380706 Dd380706 Handle barrel locks (1) 2 keys 2 keys 2 keys 2 keys Screwdriver Double Male triangle insert Male square insert no. 2433A no. 455 no. 1242E no. 3113A slot insert bar insert 7 mm 8 mm 9 mm 6 mm 7 mm 8 mm 3 mm (CNOMO) 09933 09945 09942 09943 09931 09932 09937 09934 09939 09949 09947 09948 Female square insert 6 mm 09946 (1) Others A and E combinations are available from Ronis, please contact us. Partial door inserts These inserts simply replace the standard male triangle insert (8 mm). Type Screwdriver slot insert Catalogue numbers 09981 3 mm double Male triangle insert bar insert 7 mm 8 mm (CNOMO) 09982 09983 09984 9 mm Male square insert 6 mm 7 mm 8 mm 6 mm female square insert 09985 09986 09988 09989 Finishing parts > see page 63 116 Dd380705 Dd380705 Dd380705 Dd380705 Dd380705 Door insert 09987 Prisma Plus G enclosures IP55 enclosures Spare-parts Dd384507 Accessories (IP55) 2 pillars 01025 Set of spare parts for wall-mounted enclosure 01247 Dd384508 24 screws M6 x 12 + stubs contact 4 simple fixing brackets 4 screws pillar/seating 12 nylon washers 12 self threading screws 4 conical washers 4 screws M8 x 16 Set of spare parts for door 01248 Dd384508 1 screw M6 x 12 + stub washers 2 keys no.405 1 spring nut 4 screws frame/pillar 3 hinge pins 8 o-ring joints 3 stop rings Spare parts for closing system 01249 Dd384510 1 stop washer 1 screw body 1 screw cap 1 o-ring 1 screw nut 1 composite seal 1 captive screw 1 special washer 1 cam 1 washer DD384502 DD384501 Front-plate accessories 20 front-plate locking handles with sticker 01093 10 sets of front-plate locking handles 01094 117 Dimensions Prisma Plus G enclosures IP55 enclosures A B 425 625 825 1025 1225 1425 1725 375 575 775 975 1175 1375 1675 525 725 925 1125 1325 1525 1825 Dd381728 Dd381730 Dd381727 7 11 15 19 23 27 33 H1 Dd381735 No. of vertical modules Dd381737 Doors Dd381734 Ducts Dd381729 Dd381726 Wall-mounted enclosures Dd381731 Surface utile No. of vertical modules (1) Multifix rail. (2) Recessed slotted mounting plate. (3) Transparent door. (4) Plain door. (5) Front plate. (6) Door. Dd381732 7 11 15 19 23 27 33 Canopy Dd381742 Dd381738 Dd381742 Enclosure combinations 118 C E H 420 620 820 1020 1220 1420 1720 284 484 684 884 1084 1284 1584 450 650 850 1050 1250 1450 1750 Dimensions Prisma Plus G enclosures IP55 enclosures Dd381744 Dd381733 Partial door with cut-outs Dd381745 Side panels with cut-outs Gland plates Dd381743 7 modules From 11 to 33 modules (1) Cat. no. 08376 for wall-mounted enclosures from 11 to 27 modules (2) Cat. no. 08377 for wall-mounted enclosures at least 33 modules Cat. no 08863 Dd381750 Dd381748 Dd381749 Dd381746 Functional mounting plates Cat. no 08864 Cat. no 08862 Cat. no 08861 Dd381739 Dd381740 Dd381741 Wall structure 119 Pack enclosures Pack enclosures Contents Presentation ...............................................................................123 Pack wall-mounted and flush-mounted enclosures.....................124 Kilowatt hour meters ...................................................................125 Accessories ................................................................................126 Distribution Insulated busbars .......................................................................128 Power supply of rows from the incoming device Distribution blocks.......................................................................130 Power supply of rows from the incoming device Comb busbars, distribution blocks ..............................................131 Power supply of a modular devices row Accessories ................................................................................132 Spare-parts.................................................................................133 Dimensions.................................................................................134 121 Pack enclosures Pack enclosures Metallic indoor enclosures, supplied mounted, can be ordered with a single catalogue number. 1 product reference = a complete modular enclosure ready to be equipped b 160 A b IP30 b IK07/08 PD391279 An enclosure + modular rails + front plates + blanking plates + a plastic gland plate + an earth bar + a template for drilling wall-mounted holes. Presentation Gland plate b Removable, easy-to install and easy-to-cut Accessibility b Side panels dismountable for full access Double rail b Double rail supplied premounted in the 4-, 5- and 6-row enclosures allowing mixing of devices of different depths Installation PD390161 b Door easy to install without any tool b Plain or transparent reversible door Main characteristics Steel sheet metal with electrophoresis treatment + hot-polymerised polyester epoxy powder. Enclosure: b width: 555 mm, b height: 480 to 1080 mm, b depth: 157 mm without door / 186 mm with door. Description Pack enclosures Rated operational current Colour Standards conformity Degree of protection Degree of protection against mechanical impacts Isolation Doors Mounting 160 A - Icc = 50 kA White colour RAL 9001 EN 62208, IEC 61439-2, NFC 61-910 IP30 with or without door IK08 with door IK07 without door Class 1 b Plain or transparent, opening to right or left b By design, electrical continuity of moving parts (hinges…) b Supplied with a handle and keylock (key 405) b No possibility to install push buttons (distance behind door = 42 mm) The Pack enclosures can be built-in easily using its flush mounting kit The design of Pack enclosures ensures easy device access and mounting. Optimised depth and an extra-thin door ensure perfect integration in all environments. Models with 4, 5 and 6 rows are particularly well-suited for the incomer function: b more space available for wiring of the incoming device b optimised number of front plates. 123 Pack enclosures Pack wall-mounted and flush-mounted enclosures DD383985 Wall-mounted enclosures for modular devices Enclosures include: b 1 modular rail per row (L= 24 modules of 18mm). The recessed rail at the top of 4, 5, 6-row enclosures is for NG160 installation and supplied with another rail + 4 raisers for modular devices. b earth bar, b 1 front plate with cut-out per row (height depending on model), b 1 plastic gland plate, b divisible blanking plates (number depending on model). 9 12 15 18 21 Height Width Depth 480 555 157 without door 630 175 with 780 door + 11 930 for handle 1080 Nb. of divisible Enclosure Door blanking plates Top Intermediate Bottom 225 150 225 3 250 200 6 DD381802 2 3 4 5 6 Height of front plates (mm) DD381801 Nb. of Nb. of vertical Dimensions in mm rows modules DD383299 DD383298 Doors are: b reversible, opening to left or right, b supplied with a handle and barrel with keylock (key 405), b barrel locks and inserts > see page 100 08002 08003 08004 08005 08006 Plain 08082 08083 08084 08085 08086 Transparent 08092 08093 08094 08095 08096 Flush-mounting kit > see page 127 DD383982 Enclosure extension Meters can be installed at different levels on the functional uprights of enclosures. Class 1: Depending on preferences and needs, meters can be installed directly on mounting plates equipped with earthing braids and combined with partitioning or front plates. The mounting plates can be raised using M5 spacers. Doors are: b reversible, opening to left or right, b supplied with a handle and barrel with keylock (key 405), b barrel locks and inserts > see page 100 124 Width 555 Depth 157 without door 175 with door + 11 for handle Door DD382406 Height 480 630 Enclosure DD382405 9 12 Dimensions (mm) DD382404 Nb. of vertical modules (50 mm) 08012 08013 Plain 08082 08083 Transparent 08092 08093 Pack enclosures Kilowatt-hour meters Kilowatt-hour meters, Class 2 Class 1: Depending on preferences and needs, meters can be installed directly on mounting plates (without insulating plate) equipped with earthing braids of 6 mm2 (08910) and combined with partitioning or front plates. The mounting plates can be raised using M5 spacers > see page 58 DD383982 DD383981 In an enclosure extension DD382945 In Pack wall-mounted enclosures DD382947 Installation Device Nb. of devices per row Nb. of vertical modules Mounting plate Insulating plate Horizontal partitioning (1) Front plate transparent plain Enclosure Door Single-phase meters 3 6 03157 03154 04333 03343 or 03806 Pack enclosure Depending on enclosure 3-phase meters 2 9 03152 03154 04333 03344 or 03807 Pack enclosure Depending on enclosure Earthing wire 6 mm2 Combination uprights (set of 2) 08911 - 08911 - Single-phase meters 3 6 03157 03154 03343 or 03806 08012 08092 (transparent) or 08082 (plain) 08911 08817 (2) 3-phase meters 2 9 03152 03154 03344 or 03807 08013 08093 (transparent) or 08083 (plain) 08911 08817 (2) (1) If not installed at the top of a Pack enclosure, order an addition horizontal partition (04333). (2) To make the combination more rigid, particularly during transport, it is mandatory to use a set of combination uprights secured to the rear of the switchboard. 125 Pack enclosures Accessories Gland plates DD383990 Catalogue numbers Characteristics DD383989 Gland plates Top or bottom plate with plastic gland plate 08878 - Metal gland plate 08879 Plain metal gland plate Trunking spreader DD383991 Trunking spreader Catalogue number 08821 Canopy DD383933 Canopy for IP31 Catalogue number Characteristics 08823 The canopy cannot be mounted on the existing top plate. It therefore comes with a special top plate that must be mounted in place of the existing top plate. The existing top plate is remounted at the bottom of the enclosure to allow cable entry and exit via the bottom. The addition of a canopy over a wall-mounted or floor-standing enclosure equipped with a door ensures compliance with the degree of protection IP31. Gasket DD381268 Gasket for IP43 Catalogue number Characteristics 126 08841 When the switchboard is equipped with a canopy, a gasket for the doors ensures compliance with the degree of protection IP43. L = 5.3 m Accessories Combination uprights DD383984 Combination uprights Catalogue number Characteristics 08817 Set of 2 uprights. Particularly during transport, it is mandatory to use a set of combination uprights secured to the rear of the switchboard, to make the combination more rigid. Wall mounting DD384071 Wall mounting Catalogue number Characteristics 08803 4 external wall-mounted brackets 08803 Flush-mounting kit DD381256 Flush-mount kit Catalogue number 08822 Blanking plates Blanking plates DD384029 Pack enclosures Catalogue numbers Characteristics 03220 b Blanking strip b H = 46 mm, L = 1 m 03221 b Divisible b Set of 4 b H = 46 mm, L = 90 mm Finishing parts > see page 63 127 Pack enclosures Insulated busbars power supply of rows from the incoming device Powerclip busbars 125 to 160 A PD390546_SE PD390545_SE Distribution Powerclip tap-off blocks with 6 mm² + 10 mm² terminals Clip-on covers to block off the connected cable lugs. b Compact busbars, fully insulated(IPxxB), ready for installation (supplied with supports and clip-on covers) b Copper bars: v channelled ETPH12, v threaded M6 holes every 25 mm, v can be cut every 150 mm (125 A) or 200 mm (160 A). b Mounted on insulated bases. b Delivered with supports that screw to the functional upwrights of enclosures. b Large choice of prefabricated and tested connections. b Clip-on covers protect against direct contact. Can be easily cut for the connections to the devices. b Ends are protected by shutters. Powerclip busbars 3P 4P Spare parts* L = 450 mm L = 750 mm L = 1000 mm L = 450 mm L = 750 mm L = 1000 mm 2 busbars supports + 2 end plugs + 2 screws 2 IPxxB clip-on cobers, L. 200 mm DD381380 160 A DD382673 125 A 04103 04107 04104 04108 - 04111 04121 01210 - 01201 * For more information, > see page 103 Electrical characteristics Rating 125 A 160 A Rated short-time withstand current Icw (kA rms / 1 s) 8,5 10 Rated peak withstand current Ipk (kÂ) Rated insulation voltage Ui (V) Impulse withstand voltage Uimp (kV) 20 30 500 750 8 8 Choice of connection / device Device to connect INS NG NSA 160 C120, iC120 Multiclip Modular devices 128 INS40/125 3P 4P INS160 NG125 NG160 Vigi NG160 160 A 200 A Catalogue numbers (see details on next page) 04145 + 28947 04145 + 28948 04147 or 04148 04145 or 04147 or 04148 or 04146 04147 or 04148 or 04146 04148 04147 or 04148 or 04146 04147 or 04148 04151 or 04152 04021 04151 or 04152 Pack enclosures Insulated busbars Distribution power supply of rows from the incoming device Description For the connection of Catalogue numbers Set of four 125 A connections, W = 230 mm 35 mm² ferrule + 45° ring lug (IPxxB covers 04150) NG125, NSA equipped with tunnel terminals or combbusbar INS with tunnel terminals: cat.no. 28947 or 28948 04145 Set of four 160 A connections, W = 250 mm 45 mm² ferrule + 45° ring lug (IPxxB covers 04150) NSA160, INS160, NG160, NG125 04146 One piece connection, 3/4P, 160 A, W = 150 mm Fast connection to busbars Equipped with male fittings one end for tunnel terminals Respects the degree of protection IPxxB Neutral is clearly indicated (blue) NSA160, INS160, NG160 (located on left-hand side), NG125, C120, iC120 04147 One piece connection, 3/4P, 160 A, W = 150 mm Fast connection to busbars Equipped with male fittings one end for tunnel terminals Respects the degree of protection IPxxB Neutral is clearly indicated (blue) NSA160, INS160, 04148 NG160 (located on left-hand side), Vigi NG160 (located in the middle), NG125, C120, iC120 DD383498 DD383276 DD383295 DD383274 DD383294 DD381379 Busbar connections 12 tap-off blocks with 6 mm² and 10 mm² terminals Respects the degree of protection IPxxB All device equipped with tunnel terminals Multiclip 160 A 04151 12 tap-off blocks with 16 mm² terminals Respects the degree of protection IPxxB All device equipped with tunnel terminals Multiclip 160 A 04152 Description Catalogue numbers DD381385 Accessories 8 IPxxB covers Set of 8 clip-on covers that can be cut as needed Maintain IPxxB with 90° angle lugs and/or cable sizes from 10 to 25 mm² 04150 8.8 class mounting hardware Set of 20 CHC M6 x 12 mm 04158 129 Pack enclosures Distribution blocks Distribution power supply of rows from the incoming device Polybloc 160 A DD381200 DD382981 Polybloc distribution block 160 A Set of four 160 A connections, W 380 mm Catalogue numbers Characteristics 04031 Installation on a raised modular rail Other characteristics > see page 75 04149 Two 45 mm² end fittings for tunnel terminals For the connection of: INS40/160, NG125, NG160, C120, iC120 with or without Vigi Distribloc 63, 125 and 160 A Distribloc 160 A (top connection / bottom connection) PD390657 PG123021 054947 DD383301 Distribloc 63 A Distribloc 125 A (bottom connection) (top connection / bottom connection) PB104499 Distribloc 63 A (top connection) PB104500 Types + Catalogue numbers Characteristics Distribution block 4P Connections 04040 04041 Supplied Supplied b Installation on a raised modular rail b Width: 4 modules de 18 mm Other characteristics > see page 77 04045 04046 04047 b Installation on a modular rail b Width: 6 modules of 18 mm b Connections L = 210 mm for NG125, INS40/125, C120, iC120 Supplied b Installation on a modular rail b Width: 6 modules of 18 mm b Connection for NG160, INS100/160 with or without Vigi Multi-stage distribution blocks 40, 100 and 125 A Rating Catalogue numbers Characteristics 130 Distribution block Additional neutral bar 058930d 058923 Distribution blocks 2P Distribution blocks 4P DD382813 Types 100 A 125 A 40 A 13506 13507 13508 13516 2 x 7 holes 2 x 13 holes 4 x 13 holes Other characteristics > see page 78 100 A 13510 13515 4 x 7 holes 125 A 13512 13517 4 x 13 holes 125 A 13514 13518 4 x 17 holes Pack enclosures Comb busbars, distribution blocks Distribution power supply of a modular devices row Comb busbars for DPN Lateral bracket Tooth-caps Insulated connectors 21089 21093 96 modules of 9 mm 48 modules of 18 mm 21094 21095 Set of 40 21096 21096 Set of 12 6 modules of 9 mm 3 modules of 18 mm 21098 21098 Set of 4 For 25 mm2 cables 0 - - - DD382981 Comb busbars Catalogue numbers Characteristics Two-pole Four-pole Supplied accessories 21086 21090 24 modules of 9 mm 12 modules of 18 mm Rating: 80 A Set of 1 4 lateral bracket 1 tooth-caps 21088 21092 48 modules of 9 mm 24 modules of 18 mm 2 tooth-caps Comb busbars for C60 and iC60 Lateral bracket Tooth-caps Insulated connectors 14886 14886 14887 14887 Set of 40 14888 14888 14888 14888 Set of 40 14885 14885 14885 14885 Set of 4 For 25 mm2 cables - - - DB123466 Comb busbars Catalogue numbers Characteristics One-pole Two-pole Three-pole Four-pole Supplied accessories 14881 14882 14883 14884 b Set of 1 b 24 modules of 9 mm b 12 modules of 18 mm Rating: 80 A with 1 feeding point 100 A with 2 feeding points 2 lateral bracket 14891 14892 14893 14894 b Set of 2 b 48 modules of 9 mm b 24 modules of 18 mm Multiclip distribution blocks Rating Catalogue numbers Characteristics Supplied accessories 63 A 04008 b 4P b 24 x 9 mm modules, 12 x 18 mm modules b Upstream connection: tunnel terminals for cables up to 25 mm² b Downstream connection spring terminals: v 4 for each phase (2 x 4 mm2 + 2 x 6 mm2) v 8 for the neutral (4 x 4 mm2 + 4 x 6 mm2) Clipped onto the rear of modular rail or screwed. Bared copper connections (L=100 mm) 10 of 4 mm2 + 6 of 6 mm2 DB123466 DD383403 DB404608 Distribution blocks Multiclip 80 A 04000 b 4P b 48 x 9 mm modules, 24 x 18 mm modules b Upstream connection: tunnel terminals for cables up to 25 mm² b Downstream connection spring terminals: v 6 for each phase (6 mm2) v 18 for the neutral (6 mm2) Bared copper connections 6 mm2 (12 blue + 12 black) 131 Accessories Cable running Cable-tie supports DD381819 Pack enclosures DD381820 Cable-tie supports 08867 Set of 2 Supplied with hardware for mounting on the functional uprights of the enclosure Catalogue number Characteristics Cat. no. 04257 Earth and neutral bars 04255 04206 Bare earth bar Catalogue numbers Characteristics 04201 b Size: 12 x 3 mm b Connection space: 330 mm Equipped with a 35 mm² tunnel terminal b Can receive earth blocks with spring terminals DD381560 Blocks with spring terminals DD381560 Trunking 4 horizontal sections, 60 x 30 mm, W = 450 mm + supports 12 horizontal trunking supports 2 fixing brackets, H = 15 mm (for vertical trunking) Cat. no. 04239 04243 DD381860 Cable straps 12 horizontal cable straps 4 covers for horizontal cable straps, W = 430 mm Earth blocks with spring terminals to clip 04214 04215 b 12 x 4 mm2 b Set of 4 b Length: 75 mm b 3 x 16 mm2 b Set of 4 b Length: 37 mm DD381516 Earth bar with clamps 04200 40 clamps and 1 x 35 mm² terminal Length: 450 mm Catalogue number Characteristics Accessories installed on the side 04206 H = 15 mm Set of 2 brackets Vertically on two fixing brackets secured to a functional upright. Earth bar with clamps or spring terminals Catalogue number Characteristics Fixing mode Earth bar used Earthing braid The earthing braid is used to earth a door or wicket door with devices. 132 DD384005 DD384005 08910 The braid is equipped with a 4 mm diameter lug at one end and a 6 mm diameter lug on the other 08911 Equipped with a 5 mm diameter lug at one end and a 6 mm diameter lug on the other DD384052 Catalogue numbers Characteristics Earthing wire, 6 mm2 DD381338 Earthing braid, 6 mm 2 Pack enclosures Spare-parts Front-plate (IP30) DD384498 4 modules Pack decentered plate 01264 1 front-plate 2 front-plate locking mechanisms DD384499 4.5 modules Pack decentered plate 01265 1 front-plate 2 front-plate locking mechanisms Modular rail DD384506 Pack modular device rail 01260 1 DIN rail 432 mm lenght 2 fixing brackets 2 self threading screws M5 x 10 Gland plate (IP30) DD384489 FL21 cut-out gland plate for Pack enclosure 01020 DD384502 DD384501 Front-plate accessories 20 front-plate locking handles with sticker 01093 10 sets of front-plate locking handles 01094 133 Pack enclosures Dimensions DD381951 DD383987 Wall-mounted enclosures of 2 and 3 rows Nb. of rows 2 3 H 480 630 DD383303 DB124231 Wall-mounted enclosures of 4, 5 and 6 rows Nb. of rows 4 5 6 H 780 930 1080 DD381953 DD381956 DD383988 Door 134 Pack enclosures Dimensions DD381954 Gland plates DD382916 Trunking spreader DD381955 DD380509 Wall-mounted Nb. of rows 2 3 4 5 6 H1 396 546 696 846 996 H2 546 696 846 996 1146 Supplied modular rail Upper rail in wall-mounted enclosures of 4, 5 and 6 rows DD383308 DD383306 DD383307 DD383305 DD381957 Useful depth behind front plate Rail ref. 03004 Rail ref. 03003 135 Additional information Additional information Contents Electrical characteristics........................................138 Designing Prisma Plus power circuits .........................................138 Presentation and approach............................................................................... 138 Designing connections y 630 A...................................................139 Device connections........................................................................................... 139 Compact circuit breakers NSX100 to NSX630 .................................................. 140 Incoming connection block and power supply block on Powerclip busbars........................................................................................ 141 Designing connections with cables .............................................142 Tubular lugs ...................................................................................................... 143 Designing the PEN conductor .....................................................144 Power circuit ..................................................................................................... 144 Practical information...............................................145 Connection of power cables........................................................145 Standards .................................................................. 146 Enclosure characteristics ...................................... 151 Selection of enclosures according to the premises .....................151 Properties of metal enclosures....................................................158 Thermal characteristics .........................................159 Thermal management of switchboards .......................................159 General ............................................................................................................. 159 Comparative method......................................................................................... 161 Example............................................................................................................ 163 Charts ............................................................................................................... 164 Ventilation ......................................................................................................... 165 Heating ............................................................................................................. 166 Practical information...............................................167 Tools required for mounting and connection................................167 137 Additional information Electrical characteristics Designing Prisma Plus power circuits Presentation and approach PD390311 The Prisma Plus system takes into account the installation and connection conditions of Schneider Electric devices. The entire installation complies with standard IEC 61439-1 and 2. The result is a type tested switchboard. In the following pages you will find a number of examples, validated for Prisma Plus switchboards, intended to assist in determining the busbars as well as the upstream and downstream connections for the installation. The examples assume that the devices have already been selected. A complete process involves a number of steps before making final choices (transformer, conductors, protection, etc.). Schneider Electric offers a number of tools to assist in designing a complete installation (technical guides, software). Busbar sizing The factors that must be taken into account in determining the size of busbars include: b the diversity factor. Not all the loads supplied by a set of busbars are used at full rated load or at the same time. The diversity factor is the means to determine the maximum load current used to size the busbars. Standard IEC 61439-1 and 2 §4.7 specifies the table below: Number of circuits Rated diversity factor (RDF) 2 and 3 4 and 5 6 and 9 10 and more 0.9 0.8 0.7 0.6 b the degree of protection IP. b the ambient temperature around the switchboard. Supply of devices for outgoers y 630 A Flexible copper bars with an insulating cover. To determine the required sizes for flexible bars, see the tables starting on > see page139 which indicate the correct size for each type of connected device. b an insulated flexible bar (not connected) must meet standards IEC 60243-1, (dielectric, > see page139), NFC 32201 (insulation) and IEC 60332-1 (fire) b a flexible bar connected to a device in an enclosure must comply with standard IEC 61439-1 and 2. Cables To determine the cables required, see the tables. on > see page142. They can be used to determine: b the size of cables as a function of: v the circuit breaker rating v the current v the ambient temperature around the switchboard b the permissible current for individually tied cables or touching cables as a function of: v the size of the cables v the degree of protection for the switchboard. Easy design with Rapsody software > see page 25 138 Additional information Electrical characteristics Designing connections y 630 A Device connections Flexible copper bars with an insulating sheath Switchboards that comply with standard IEC 61439-1 and 2 It is imperative to use the values indicated below that have been validated for the installation of devices in Prisma Plus switchboards. The parameters determining the size of flexible bars are: b the environment in which the devices are installed: v position in the enclosure v dimensions of other conductors in the circuit v ambient temperature around the switchboard b the characteristics of the connected devices: v device heat losses v the type of installation (horizontal or vertical) v the type of device (fixed or withdrawable). Only the equipment manufacturer with in-depth knowledge on: b the characteristics of the installed devices b the configuration of the installation in the enclosure can provide the correct sizes of flexible bars for a given permissible current. Insulated, flexible bars make for easy, fast and flexible implementation up to 630 A, but higher ratings require sizes that cancel these advantages. For high Isc values, it is advised to use rigid bars which require fewer supports. Insulated flexible bars are better than cables, they offer: b better insulation temperature withstand (125 °C for bars, 105 °C for cables) and a larger exchange surface for an equivalent size, i.e. a smaller size for a given current b greater rigidity offering better electrodynamic characteristics for short-circuit currents b no intermediate parts (lugs) for a direct connection between the device and the busbars therefore less temperature rise and less risk of error b fast implementation of prefabricated connections already cut to length, formed and drilled. Technical characteristics b thickness of the insulation: variable depending on the bar size, 2 mm on average b rated insulation level Ui = 1000 V b impulse withstand voltage Uimp = 12 kV b maximum withstand temperature of insulating material = 125 °C. Connection In all enclosures with IP y 55 b the switchboard internal temperature is 60 °C b the withstand temperature of the insulating material is 125 °C. If the withstand temperature of the insulation is only 105 °C, use the next largest flexible bar. The bar sizes (S) indicated below take into account the derating curves of devices. Connection of devices and distribution blocks to busbars Device INS125 INS160 INS250 S (mm) Device 20 x 2 20 x 2 20 x 3 NSX250 (1) NSX400 (1) NSX630 S (mm) 20 x 3 32 x 5 32 x 8 INS320 INS400 32 x 5 INF250 ISFT250 24 x 5 INS500 INS630 32 x 6 INF400 ISFT400 32 x 5 NSX100 (1) NSX160 (1) 20 x 2 INF630 ISFT630 32 x 8 20 x 3 (1) The values for circuit breakers apply to contactors with the same ratings. To connect a Compact NSX250 to Powerclip busbars, use a 24 x 5 mm flexible bar (04746). Device S (mm) Multiclip distribution Polypact distribution Polypact distribution block (200 A) block (3P) block (4P) 20 x 3 32 x 6 32 x 5 Disconnectors, terminal blocks, connections, busbars to busbars I max. (60 °C) S (mm) 200 A 20 x 2 250 A 20 x 3 400 A 24 x 5 400 A 24 x 5 480 A 24 x 6 520 A 32 x 5 580 A 32 x 6 660 A 32 x 8 Note: the values indicated above have been validated for Prisma Plus switchboards. 139 Additional information Electrical characteristics Designing connections y 630 A Compact circuit breakers NSX100 to 630 Compact NSX100 to NSX250 Insulated flexible copper bars Devices Rated current of a circuit Inc (A) Ambient temperature around the switchboard 25 °C 30 °C 35 °C 40 °C 45 °C 50 °C 20 x 2 100 20 x 2 125 20 x 3 160 20 x 3 250 20 x 2 100 20 x 3 160 20 x 3 250 20 x 2 97.5 20 x 2 122 20 x 3 156 20 x 3 244 20 x 2 100 20 x 3 160 20 x 3 250 20 x 2 95 20 x 2 119 20 x 3 152 20 x 3 238 20 x 2 100 20 x 3 160 20 x 3 237.5 20 x 2 92.5 20 x 2 116 20 x 3 147 20 x 3 231 20 x 2 100 20 x 3 160 20 x 3 237.5 20 x 2 90 20 x 2 113 20 x 3 144 20 x 3 225 20 x 2 100 20 x 3 160 20 x 3 225 20 x 2 85 20 x 2 100 20 x 3 140 20 x 3 198 20 x 2 100 20 x 3 160 20 x 3 225 IP y 55 NSX100 TMD-TMG NSX125 TMD-TMG NSX160 (1) TMD-TMG NSX250 (1) TMD-TMG NSX100 STR NSX160 STR NSX250 (2) STR Size per phase Inc (A) Size per phase Inc (A) Size per phase Inc (A) Size per phase Inc (A) Size per phase Inc (A) Size per phase Inc (A) Size per phase Inc (A) (1) For a withdrawable NSX160 or NSX250 equipped with a Vigi or an insulation-monitoring module, multiply the In values by 0.9. (2) For a withdrawable NS250 equipped with a Vigi or an insulation-monitoring module, multiply the In values by 0.86. Compact NSX400 to NSX630 Insulated flexible copper bars Devices Rated current of a circuit Inc (A) Ambient temperature around the switchboard 25 °C 30 °C 35 °C 40 °C 45 °C 50 °C Size per phase Inc (A) Size per phase Inc (A) Size per phase Inc (A) Size per phase Inc (A) Size per phase 32 x 5 400 32 x 5 400 32 x 5 400 32 x 6 630 32 x 8 32 x 5 400 32 x 5 390 32 x 5 390 32 x 6 615 32 x 8 32 x 5 400 32 x 5 380 32 x 5 380 32 x 6 600 32 x 8 32 x 5 390 32 x 5 370 32 x 5 370 32 x 6 585 32 x 8 32 x 5 380 32 x 5 360 32 x 5 360 32 x 6 570 32 x 8 32 x 5 370 32 x 5 350 32 x 5 350 32 x 6 550 32 x 8 Inc (A) 570 550 535 520 505 490 IP y 55 NSX400B/F/N/H/S/L fixed NSX400B/F/N/H/S/L with Vigi NSX400B/F/N/H/S/L withdrawable NSX630B/F/N/H/S/L fixed NSX630B/F/N/H/S/L with Vigi or withdrawable Note: the values indicated above have been validated for Prisma Plus switchboards. 140 Additional information Designing connections y 630 A Electrical characteristics Incoming connection block and power supply block on Powerclip busbars Compact NSX100 to NSX630 Horizontal mounting Determining the permissible current of NSX100 to NSX630 connection and power supply blocks as a function of the ambient temperature around the switchboard and their IP degree of protection. Device Rated current of a circuit Inc (A) Ambient temperature around the switchboard 25 °C 30 °C 35 °C 40 °C 45 °C 50 °C IP y 31 IP > 31 IP y 31 IP > 31 IP y 31 IP > 31 IP y 31 IP > 31 IP y 31 IP > 31 IP y 31 IP > 31 NSX100 TMD-TMG Incoming connection block via the top 04066 100 via the bottom 04067 Incoming connection block via the top 04066 100 via the bottom 04067 Incoming connection block via the top 04066 160 via the bottom 04067 via the top 04066 160 Incoming connection block via the bottom 04067 via the top 04066 238 Incoming connection block via the bottom 04067 NSX400B/F/ N/H/S/L fixed NSX630B/F/ N/H/S/L fixed Incoming connection block via the top 04066 250 via the bottom 04067 Power supply block 04060 Incoming connection block 04076 400 Power supply block 04070 Incoming connection block 04076 570 Power supply block 04071 b connection not possible. 97 87 95 85 92 b 100 100 97 100 95 100 92 100 90 97 b 152 160 147 160 144 156 140 152 136 147 b 160 160 156 160 152 160 147 160 144 156 b 213 231 207 225 200 219 193 213 185 207 b 219 245 213 238 207 225 200 219 193 213 b 360 390 350 380 340 370 330 360 320 350 b 520 555 505 540 490 525 470 510 450 495 b 04060 Power supply block NSX250STR 90 04060 Power supply block NSX250 TMD-TMG 100 04060 Power supply block NSX160STR 92 04060 Power supply block NSX160 TMD-TMG 100 04060 Power supply block NSX100STR 95 The indicated performance characteristics are valid for: b Compact NSX100/160/250/400 circuit breakers used as incoming or outgoing devices b Compact NSX630 circuit breakers used as incoming device. Note: the values indicated above have been validated for Prisma Plus switchboards. 141 Additional information Electrical characteristics Designing connections with cables Cables Practical guidelines Schneider Electric provides cabling recommendations according to the rating of the circuit breaker. The size of cables must be selected according to: b the level of current b the ambient temperature around the conductors b the degree of protection for the switchboard. The tables below take into account the installation conditions for each type of device (permissible temperature at connection terminals, etc.). They follow the temperature derating values for installed devices in all enclosures with cover panels rated IP y 55. b switchboard internal temperature 60 °C b connections using copper cables. For System G, the volumes, ratings and connection lengths are low. Select the values in the “Cables tied together” column, according to the IP. Connection of circuit breakers Size of cables (mm²) 1.5 2.5 4 6 10 16 25 35 50 70 95 Permissible current (A) Cables tied individually IP y 31 IP > 31 16 25 32 40 63 90 110 135 180 230 275 14 25 29 39 55 77 100 125 150 190 230 Cable tied together IP y 31 IP > 31 14 22 28 36 55 80 100 125 12 20 24 33 50 70 93 120 Connection of other devices Size of cables (mm²) 1.5 2.5 4 6 10 16 25 35 50 70 95 Permissible current (A) Cables tied individually IP y 31 IP > 31 13 23 28 36 55 80 100 120 165 210 250 12 21 26 35 50 70 90 115 135 176 210 Cable tied together IP y 31 IP > 31 12 20 25 32 50 72 90 110 10 19 22 30 46 63 84 103 Connection of NSX100 to 630 A Device Size (mm²) NSX100 NSX160 NSX250 25 50 95 Note: Schneider Electric recommends connecting NSX400/630 circuit breakers with insulated flexible bars or rigid bars. > see page 139 Note: the values indicated above have been validated for Prisma Plus switchboards. 142 Additional information Electrical characteristics Designing connections with cables Tubular lugs Tubular lugs for incoming connection blocks Maximum size of lugs for connection to the different incoming connection blocks. Standard Cu lugs Narrow Cu lugs Narrow bimetal lugs Incoming connection block for NSX-INS250 supplied via the top or bottom, cat. no. 04066 and 04067 150 mm² 240 mm² 185 mm² In-duct incoming connection block for NSX630, cat. no. 04076 240 mm² 300 mm² 300 mm² DD382788 Narrow bimetal lugs Catalogue numbers selection Catalogue numbers Cable size (mm²) Quantity 150 150 185 185 240 240 300 300 3 4 3 4 3 4 3 4 Lugs for aluminium cable(1) 29504 29505 29506 29507 32504 32505 32506 32507 (1) Supplied with 2 or 3 interphase barriers. 143 Additional information Electrical characteristics Designing the PEN conductor Power circuit Size of PEN protective conductor Practical guidelines The size of the PEN is determined in the same manner as a neutral conductor, i.e.: b for copper single-phase circuits or sized y 16mm², it must be the same size as the phase conductors b for copper three-phase circuits sized > 16 mm², it can be: v the same size as the phase conductors v smaller on the condition that: - the current likely to flow in the neutral during normal operation is less than the permissible current for the conductor - the power rating of single-phase loads does not exceed 10 % of the total rating. The conductor must be accessible to enable connections both in the factory and on site, as well as checks on the tightness of connections. Implementing the PEN protective conductor Practical guidelines According to standard IEC 61439-1 and 2, the practical guidelines for implementing the PEN are the following: b at the entry to the assembly, the PEN connection must be next to the phase connections b within the assembly, the PEN does not need to be insulated from the exposed conductive parts (except on sites where there is a risk of fire or explosion) b the size of the conductor must be at least equal to that of the neutral b the size must remain constant throughout the main busbars b the change from a TNC to a TNS system must take place at a single point in the switchboard, via a marked neutral-disconnection bar that is accessible and can be dismantled to facilitate the impedance measurement of the fault loop b after the TNS creation point, it is forbidden to recreate a TNC system. The PE and the neutral must meet their specific requirements. 144 Additional information Practical information Connection of power cables b To ensure protection of persons, first connect the switchboard protective conductor to the earth electrode. b Tie the cables as close as possible to the connections to avoid any mechanical stresses on the device terminals. When not using cable glands, also attach the cables near to the cubicle entry point. b Cables must never be in contact with or passed between live conductors. b Sharp edges of the framework must be protected where cables pass to avoid damaging the conductors. b Comply with a minimum radius of curvature of 6 to 8 times the cable outside diameter. b All power connections must be made with class 8.8 mounting hardware and elastic contact washers, tightened to the torque indicated in the table below. b When connecting aluminium cables to copper terminals, use bimetal lugs or interfaces. b Separate the different types of circuits into separate cable bundles (power, control, 48 V, 24 V, DC, AC, etc). Cable bundles Cable cross-sectional area (mm² ) CSA y 10 16 < CSA y 50 CSA u 50 Max. number of cables per bundle 8 4 Tie individually Tying the cable bundles Type of tie Width: 4.5 mm Load: 22 kg Width: 9 mm Load: 80 kg Maximum Icw (kA/rms 1s) 10 15 20 20 25 35 45 Distance between ties (mm) 200 100 50 350 200 100 70 For cable sizes of 50 mm² or more, use 9 mm wide fixing ties. Recommended tightening torque for mechanical and electrical connections with 8.8 class screws. Diameter of screw M3 M4 M5 M6 M8 M10 M12 Tightening torque (Nm) (with nut + contact washer) 1.5 3.5 7 13 28 50 75 145 Additional information Standards Standards What is a standard? A common reference "A standard helps to define a common language between economic stakeholders (producers, users and consumers), to clarify and harmonize practices and to define the levels of quality, safety, compatibility, and least environmental impact of products, services and practices. Standards facilitate trade, both national and international, and help to better structure the economy and facilitate the everyday life of everyone." Afnor definition IEC international standards The IEC (International Electrotechnical Commission) is a worldwide organisation for standardisation comprising all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote international cooperation on all questions concerning standardisation in the electrical and electronic fields. To that end, the IEC publishes International Standards. Their preparation is entrusted to technical committees and any IEC National Committee interested in the subject dealt with may participate in the preparatory work. National standards In Europe The IEC documents are first studied by CENELEC, which establishes: b either a European standard (EN), often identical to the IEC standard, which then becomes the applicable national standard in all the member countries b or, in the event of differences, a harmonisation document (HD). Other IEC member countries Each country is autonomous and can accept the IEC standard as the national standard, with or without modifications. Even though they are IEC members, countries such as Japan and the United States continue to develop their own standardisation systems. DD383972 Countries without a standardisation system It is possible to refer to an IEC standard in the framework of a project. Worldwide Other IEC member countries Countries CEI / IEC Commission Electrotechnique Internationale CENELEC Comité Européen de Normalisation ELECtrotechnique UTE Union Technique de l’Électricité VDE Verband der Elektrotechnik, Elektronik und Informationstechnik e.v. (German electrotechnical, electronics and computer technology standardisation organisation) BSI British Standards Institution 146 Additional information Standards Standards The different types of standards Management standards DD381776 DD381775 There are different types of standards, including: b management standards b installation standards b product standards. ISO 9004: Quality-management systems - guidelines for performance improvements. Used in setting up a quality-management system. ISO 9001: Quality management systems - requirements. Used for certification audits. Switchgear and controlgear assemblies. ISO 14004: Environmental-management systems. General guidelines on the principles, systems and supporting techniques. ISO 14001: Environmental-management systems. Specification with guidance for use. DD381778 DD381777 Design and manufacture. The majority of Schneider Electric development centres and factories are certified ISO 9001 and ISO 14001. Low voltage installation standards Switchgear and controlgear. Installation. The set of IEC 60364 standards defines the main principles and rules for the design and the mounting of the electrical installation: b determining general characteristics of installations b protection b selection and installation of equipment b verification and maintenance of installations. Switchgears standards They apply to devices or assemblies and are aimed at ensuring correct operation and safety of the concerned products: b v v v v v standards on low-voltage switchgear and controlgear: IEC 60947-1: general rules IEC 60947-2: circuit breakers IEC 60947-3: switches and disconnectors IEC 60947-4: contactors IEC 62208: empty enclosures. b The IEC 61439 switchboard standard The IEC 61439 standard: v characterizes the electrical switchboard and specifies the design, construction and verification rules v describes in detail all low-voltage switchgear and controlgear: definitions, technical characteristics, conditions of use, and construction and verification requirements v applies to power switchgear and controlgear assemblies (PSC assemblies) whose rated voltage does not exceed 1000 V in alternating current or 1500 V in direct current. Regulations in a given country may make certain standards legally binding and may also create additional safety requirements. In addition to providing proof of the conformity of its quality-management system, a product manufacturer can demonstrate the quality of products by providing proof that the design and manufacture comply with the requirements in the applicable standard. Proof of conformity may be a declaration by the manufacturer or a certificate supplied by an independent organisation. 147 Additional information Standards Standards Enclosure standards Standard IEC 62208 lay down definitions, classifications, characteristics and test requirements for enclosures used for switchgear and controlgear assemblies. They apply to empty enclosures before installation of the devices by the panelbuilder, as supplied by the manufacturer. They apply to one-piece enclosures and to enclosures supplied in kit form. Type tests of standard IEC 62208 1 - Static load 2 - Hoisting 3 - Axial loads of metal inserts 4 - IK code 5 - IP code 6 - Thermal stability 7 - Resistance to heat 8 - Resistance to abnormal heat and to fire 9 - Dielectric strength 10 - Protective-circuit continuity 11 - Weather resistance 12 - Corrosion resistance 13 - Marking e marking e marking is a regulatory symbol attributed under the sole responsibility of the manufacturer and intended for the verification authorities of the European countries that enforce the European regulations. It allows free circulation of a product in the European Union and certifies that it complies with the basic requirements in all the applicable European directives. e marking is not a quality symbol and does not indicate conformity with a standard The e declaration is intended exclusively for the authorities in charge of verifying compliance with the applicable regulations and it is drafted, signed and held for presentation to the authorities by the manufacturer. For the Prisma Plus range, the declaration is the responsibility of the Schneider Electric unit that has designed and developed the product. For LV switchboards, the declaration is the responsibility of the panelbuilder. The following products receive e marking: b all products that are liable to endanger the safety of persons, animals and property (LV directive) b all products likely to emit electromagnetic disturbances above a standardised threshold or to be disturbed during operation (EMC directive). Consequences: b the Prisma Plus range falls under the LV directive only b LV switchboards are covered by the LV directive and may also fall under the EMC directive, depending on the type of devices incorporated. e 148 For the Prisma Plus range, e marking is applied: b on the packing of "mechanical" components b on the product itself for "electrical" components. For the LV assemblies created by the panelbuilder, e marking is applied: b on the packing b on the rating plate (if applicable) b on one of the documents accompanying the switchboard when it is shipped. Additional information Standards Standards Degree of protection Standard IEC 60364-5-51 lists and codifies a large number of external influences to which electrical installations can be subjected, including the presence of water, solid objects, shocks, vibrations, corrosive substances, etc. IP code Standard IEC 60529 (IP code, February 2001) indicates the degrees of protection provided by an enclosure for electrical devices against access to hazardous parts, against penetration of solid foreign objects and against penetration of water. These standards do not apply for the protection against the risks of explosion or conditions such a humidity, corrosive vapour, fungus or vermin. The IP code is made up of two characteristic numerals and can include an additional letter when the actual protection for persons against access to the hazardous parts is better than that indicated by the first numeral. The first numeral characterises the protection provided against the ingress of solid foreign objects and the protection of persons. The second numeral characterises the protection provided against the ingress of water with harmful effects. Protected against vertically dripping water (condensation) 2 Protected against dripping water up to 15° from vertical 3 Protected against spraying water up to 60° from vertical 4 Protected against splashing water from all directions 5 Protected against water jets from all directions 6 Protected against powerful water jets from all directions 7 Protected against the effects of temporary immersion in water 8 Protected against the effects of continuous immersion in water DD381971 DD381970 DD381969 DD381968 DD381967 DD381966 1 DD381972 Dust tight 2nd numeral Protection against ingress of water DD381973 Protected against access with a wire DD381959 6 Protected against dust (dust protected) DD381963 Protected against access with a wire DD381961 5 Protection against solid foreign objects larger than 1 mm DD381962 4 Protected against access with a wire Protection against solid foreign objects larger than 2.5 mm DD381964 4 Protection against solid foreign objects larger than 12.5 mm DD381965 Protected against access with a tool DD381959 3 DD381960 2 Protected against access with a finger DD381961 2 Protection against solid foreign objects larger than 50 mm DD381962 Protected against access with back of hand DD381962 1 Protection against ingress of solid objects DD381962 1st numeral Protection of persons 149 Additional information Standards Standards Additional letter The additional letter is used only if the actual protection of persons is higher than that indicated by the first characteristic numeral of the IP code. Additional letter Protection A B C D A Protected against access with back of hand B Protected against access with a 12 mm diameter finger C Protected against access with a 2.5 mm diameter tool D Protected against access with a 1 mm diameter wire If only the protection of persons is of interest, the two characteristic numerals are replaced by the letter "X", e.g. IPXXB. Illustration of the above explanations: Protection against solid foreign objects larger than 2.5 mm IP30D No protection Protected against access with a 1 mm diameter wire Remarks b The degree of protection IP must always be read and understood numeral by numeral and not as a whole. For example, an IP31 wall-mount enclosure is suitable for an environment that requires a minimum degree of protection IP21. However an IP30 wall-mount enclosure is not suitable. b the degrees of protection indicated in this catalogue are valid for the enclosures as presented. However, the indicated degree of protection is guaranteed only when installation and device mounting are carried out in accordance with professional standards that conserve the initial degree of protection. IK code Standard IEC 62262 defines an IK code characterising the capacity of products to resist mechanical impacts from all sides. IK code 01 02 03 04 05 06 07 08 09 10 Impact energy (joules) 0.14 0.2 0.35 0.5 0.7 1 2 5 10 20 IK codes can be selected according to the risks of impacts on a given site. 150 Site Recommended IK No risk of major impact Technical premises 07 Significant risk of impact that can damage devices Hallways 08 (switchboard with door) Maximum risk of impact that can damage the switchboard Workshops 10 Additional information Selection of enclosures according to the premises Enclosure characteristics The IP and IK degrees of protection provided by an enclosure must be specified as a function of the various external influences defined by standard IEC 30364-5-51, in particular: b presence of foreign solid bodies (code AE) b presence of water (code AD) b mechanical stress (code not specified) b capability of persons (code BA) b ... Prisma Plus switchboards are designed for indoor installation. Unless the rules, standards and regulations of a specific country stipulate otherwise, Schneider Electric recommends the following IP and IK values based on French guide UTE C 15-103 (March 2004). Using the table 1 Opposite the relevant premises, read the recommended IP and IK values. 2 The b symbol indicates the enclosure or cubicle satisfying the criteria of the UTE guide. Any enclosure or cubicle with a higher degree of protection can also be used. 3 If several degrees of protection are possible (refer to the standard for more details) and the v and b symbols are indicated (e.g. 24v/25b), enclosures that correspond to the higher degree of protection (b) are suitable for the lower degree of protection (v). Example: Selection of an enclosure for a laundry room. Minimum degree of protection: IP21/IK02 A wall-mounted enclosure with a door (plain or transparent), a canopy and a gasket offer IP43/IK08 degrees of protection and are therefore suitable for this application. Type of premises Enclosures Wall-mounted enclosure without door with door with door + canopy with door + canopy + gasket Floor-standing enclosure without door with door with door + canopy IP30/IK07 IP30/IK08 IP31/IK08 with door + canopy+ gasket IP43/IK08 Min. IP/IK required IP IK Domestic or comparable premises or locations 24 07 Porch IP55 IP55/IK10 b Bathrooms (see washrooms) Bicycles, motorcycles, tricycles, etc. (premises for) 20 07 Water, sewer and heating connections 23 02 Laundries 21 02 Cellars, garages, furnace rooms 20 02/07 b b b b b Bedrooms 20 02 Trash rooms 25 07 Halls in cellars 20 07 Courtyards 24/25 02/07 Kitchens 20 02 b b b b Shower rooms (see washrooms) Indoor stairways and alleys 20 02/07 Outdoor stairways and outdoor alleys without roofs 24 07 Outdoor alleys with roofs 21 02 Attics (roof space) 20 02 Garden shelters 24/25 02/07 Latrines 20 02 Dustbin rooms 25 02/07 Ironing room 20 02 Access ramps to garages 25 07 b b b b b b b N/A 151 Additional information Selection of enclosures according to the premises Enclosure characteristics Type of premises Washrooms, rooms containing a bathtub or shower Enclosures Wall-mounted enclosure without door with door with door + canopy with door + canopy + gasket Floor-standing enclosure without door with door with door + canopy IP30/IK07 IP30/IK08 IP31/IK08 with door + canopy + gasket IP43/IK08 volume 0 Min. IP/IK required IP IK 27 02 volume 1 24 02 volume 2 23 02 volume 3 IP55 IP55/IK10 b b 21 02 Lounges, living rooms, etc 20 02 Drying rooms 21 02 Covered terraces 21 02 WCs 20 02 b Verandas 20 02 b Crawl spaces 23 07 b b b b Commercial premises and adjoining areas Gunsmiths (storage area, workshop) 30 08 Laundries (wash room) 24 07 Butchers shop 24 07 cold room: y -10 °C 23 07 Bakers, cake shops (kitchens) 50 07 Coffee roasters 21 02 Coal, wood, oil 20 08 b b b b b b b Delicatessen (production) 24 07 Sweets (production) 20 02 b Shoe repair shops 20 02 b Dairies 24 02 Hardware stores (storage areas for chemicals and paint) 33 07 Wood workers 50 07 Art galleries 20 02/07 Florists 24 07 Furriers 20 07 b b b b b b b Fruit and vegetable merchants 24 07 b Grain shops 50 07 b Bookshops, stationers 20 02 Motorcycle and bicycle repairs and accessories 20 08 Messenger services 20 08 Furniture shops (antiques, secondhand) 20 07 b Glass and mirror merchants (workshop) 20 07 b Wallpaper shop (storage area) 20 07 b Cosmetics shop (storage area) 20 02 b Chemists (storage area) 20 02 b Photographers (dark room) 23 02 Plumbers (storage area) 20 08 b b b b b Fishmongers 25 07 Dry cleaners 23 02 Hardware stores (without paint, chemicals, etc.) 20 07 Locksmiths 20 07v/08b v Vintners, spirits 20 07 Interior decorator (carding) 50 07 Tailors, clothing retailers (storage area) 20 02 Pet care 35 07 N/A 152 b b b b b b b b Additional information Selection of enclosures according to the premises Enclosure characteristics Type of premises Enclosures Wall-mounted enclosure without door with door with door + canopy with door + canopy + IP55 gasket Floor-standing enclosure without door with door with door + canopy IP30/IK08 IP31/IK08 with door + canopy + gasket IP43/IK08 IP55/IK10 Min. IP/IK required IP IK Buildings open to the general public Shared premises of storage rooms buildings open to the packing rooms general public archive rooms IP30/IK07 20 08 20 08 20 02 b film and magnetic media storage 20 02 b linen rooms 20 02 b laundry rooms 24 07 misc. shops 21 07/08 b b b b kitchens (large) J Reception old and handicapped people 20 02 b L Lecture halls, halls meeting rooms, stage areas auditoriums, scenery storage halls used for several purposes rooms costume rooms 20 02/07 b 20 08 b 20 08 b 20 07 Retail premises, sales premises shopping malls areas for storage and handling of packing 20 08 b 20 08 b N Restaurants and cafes 20 08 O Hotels and boarding houses 20 02 b P Dance halls and gaming parlours 20 07 b R Teaching classrooms establishments, dormitories holiday camps 20 02 b 20 08 M S Libraries and documentation centres T Exhibitions U Healthcare establishments b b b 20 02 b halls and rooms 20 02 b areas for reception of equipment and merchandise 20 07 b bedrooms 20 02 b incineration 21 07/08 operating rooms 20 07 centralised sterilisation 24 02/07 b b b pharmacies and labs 21v/23b 02v/07b with more than 10 l of inflammable liquids v V Places of worship 20 02 b W Administrative premises, banks 20 02 b X Indoor sports facilities 20 07v/08b v halls premises containing 21 refrigeration facilities 08 02 Y Museums 20 PA Covered open air facilities 23v/25b 08v/10b b b b b v b CTS Marquees and tents 44 08 b SG Inflatable structures 44 08 b PS 21 08v/10b Covered parking lots v b 153 Additional information Selection of enclosures according to the premises Enclosure characteristics Type of premises Enclosures Wall-mounted enclosure without door with door with door + canopy with door + canopy + gasket Floor-standing enclosure without door with door with door + canopy IP30/IK07 IP30/IK08 IP31/IK08 with door + canopy + gasket IP43/IK08 Min. IP/IK required IP IK Technical premises Battery rooms 23 02/07 Lifts (machine rooms and pulley rooms) 20 07v/08b v Electrical rooms 20 07 b Control rooms 20 02 b Workshops 21v/23b 07v/08b v b Laboratories 21v/23b 02v/07b v b Air conditioning washers 24 07 Garages (used exclusively for parking vehicles) of an area not exceeding 100 m2 21 07 b b Machine rooms 31 07/08 Water pressurisers 23 07/08 IP55 IP55/IK10 b b b b Boiler houses and adjoining premises (power in excess of 70 kW) Boiler rooms Fuel storage areas coal fuel 51v/61b 07v/08b other fuel 21 07/08 b electrical 21 07/08 b coal 50v/60b 08 oil 20 07v/08b v b b v v 20 07v/08b v Cinder tips 50 08 Pump rooms 21v/23b 07v/08b Pressure reduction rooms (gas) 20 Steam or hot water facilities Expansion vessel rooms liquefied gas b v b 21v/23b 07v/08b v b 21 b 07v/08b v b 02 Garages and car parks of an area exceeding 100 m2 Parking lots 21 07v/10b Carwash areas (inside premises) 25 07 Petrol stations 21 07 inside v b b b outside Lubrication areas 23 08 b Battery recharging areas 23 07 b Workshops 21 08 b Public building (other than for the general public) Offices 20 02 b Libraries 20 02 b Archives 20 02 b Computer rooms 20 02 b Design offices 20 02 b Rooms containing reprographic machines 20 02 b Sorting rooms 20 07 b Refectories in restaurants or canteens 21 07 Sports rooms 20 07v/08b v Barracks 20 07 b Meeting rooms 20 02 b Waiting rooms, lounges, halls 20 02 b Medical consulting rooms, not fitted with specific equipment 20 02 b 02/07 b b Large kitchens Demonstration and exhibition rooms 20 N/A 154 b Additional information Enclosure characteristics Type of premises Selection of enclosures according to the premises Enclosures Wall-mounted enclosure without door with door with door + canopy with door + canopy + IP55 gasket Floor-standing enclosure without door with door with door + canopy IP30/IK07 IP30/IK08 IP31/IK08 with door + canopy + gasket IP43/IK08 IP55/IK10 Min. IP/IK required IP IK Farm premises or locations Alcohol (storage) 23 07 Closed cattle sheds 35 07 b Laundries 24 07 b b Wood storage rooms 30 10 b Threshing floors 50 07 b Distilling cellars 23 07 b Vat rooms (wine) 23 07 b Courtyards 35 07 b Poultry barns 35 07 b Stables 35 07 b Fertiliser (storage) 50 07 b Stables 35 07 b Manure heaps 24 07 b Haylofts 50 07 b Haystacks, forage (storage) 50 07 b Granaries, barns 50 07 b Straw (storage) 50 07 b Greenhouses 23 07 Grain silos 50 07 b Milking rooms 35 07 b b Pig sties 35 07 b Chicken houses 35 07 b Miscellaneous installations Fair facilities 33 08 Water treatment facilities 24/25 07/08 b b Thermodynamic installations, air-conditioned rooms and cold rooms 25 07 Height above from 0 to 1.10 m ground 24 07 from 1.10 to 2 m above 2 m under evaporator or water drain pipe 21 07 ceiling and up to 10 cm underneath 23 07 Temperature y -10 °C 23 07 Compressor room 21 08 34 integral unit located outside or on a terrace 08 b b b b b b N/A 155 Additional information Selection of enclosures according to the premises Enclosure characteristics Type of premises Enclosures Wall-mounted enclosure without door with door with door + canopy with door + canopy + gasket Floor-standing enclosure without door with door with door + canopy IP30/IK07 IP30/IK08 IP31/IK08 with door + canopy + gasket IP43/IK08 Min. IP/IK required IP IK Industrial facilities Slaughter houses Batteries (manufacture) Acid (manufacture and storage) Alcohol (manufacture and storage) Aluminium (manufacture and storage) Livestock (raising, fattening and sale) Asphalt and bitumen storage Wool beating and carding Industrial laundry Wood (processing) Meat packers Bakeries Breweries Brickworks Rubber (production and processing) Carbide (manufacture and storage) Ammunition factories Carton board (production) Quarries Celluloid (manufacture of objects) Cellulose (manufacture) Coal (depots) Pork products Boiler-making works Lime kilns Rag (storage) Chlorine (manufacture and storage) Chrome-plating Cement works Coking plant Adhesives (production) Bottling lines Liquid fuels (storage) Fats (processing) Leather (tanning and storage) Copper (ore processing) Paint stripping Detergents (manufacture) Distilleries Electrolysis Ink manufacturing Fertilisers (manufacture and storage) Explosives (manufacture and storage) Iron (production and processing) Spinning mills Furriers (beating process) Cheese factories Gas (production and storage) Tar (processing) Seed production Metal engraving Oils (extraction) Petroleum products (manufacture) Printworks 156 55 33 33 33 51 08 07 07 07 08 45 53 50 24/25 50 24/25 50 24 53 54 51 53 33 55 30 34 53 24/25 30 50 30 33 33 50 53 33 35 31v/33b 51 31 31 54 53 33 33 31 53 55 07 07 08 07 08 07 07 07 08 07 07 08 07 08 08 08 08 07 08 08 07 07 07 08 08 07 08 08 07 08 08 08 07 07 08 07 07 08 51 50 50 25 31 33 50 33 31 33v/34b 20 08 07 07 07 08 05 07 07 07 08 08 IP55 IP55/IK10 b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b b v b b b b b b b b b b b b b b b b b b b v b Additional information Enclosure characteristics Type of premises Selection of enclosures according to the premises Enclosures Wall-mounted enclosure without door with door with door + canopy with door + canopy + gasket Floor-standing enclosure without door with door with door + canopy IP30/IK07 IP30/IK08 IP31/IK08 with door + canopy + gasket IP43/IK08 Min. IP/IK required IP IK Industrial establishments (continued) Dairies 25 07 IP55 IP55/IK10 b Public wash-houses 25 07 Liqueurs (production) 21 07 b Halogenated liquids (use) 21 08 b Inflammable products (storage and workshops where they are used) 21 08 b Magnesium (production, storage and 31 use) 08 b Machine rooms 20 08 Plastics (production) 51 08 Cabinet makers 50 08 Metals (processing) 31v/33b 08 Combustion engines (testing of) 30 08 Ammunition storage 33 08 b Nickel (ore processing) 33 08 b 07 b b b b v b b Household waste (processing) 54 Paper (production) 33v/34b 07 Paper (storage) 31 07 b Perfume (production and storage) 31 07 b Pulp mill 34/35 07 Paint (production and storage) 33 08 Plaster (processing and storage) 50 07 Gunpowder factory 55 08 Chemicals (production) 30v/50b 08 Oil refineries 34/35 07 Salt preserve factories 33 07 Soap (production) 31 07 Saw mills 50 08 Metalwork shops 30 08 b v b b b b b v b b b b b b Grain or sugar silos 50 07 Silk and artificial hair factories 50 08 Sodium carbonate (processing and storage) 33 07 Sulphur (processing) 51 07 Spirits (storage) 33 07 Sugar mills 55 07 b Tanners 35 07 b Dye works 35 07 b Textile and fabric (production) 51 08 Varnish (production and application) 33 08 Glass works 33 08 Zinc works 31 08 b b b b b b b b b 157 Additional information Enclosure characteristics Properties of metal enclosures Schneider Electric enclosures comply with standard IEC 62208 for empty enclosures. The sheet metal used for Schneider Electric enclosures receives an anti-corrosion epoxy electrophoresis treatment and a coating of a thermosetting, polyester-resinmodified epoxy powder for colour and appearance. This two-coat system provides excellent finish and corrosion protection. The characteristics of this coating are much better than those of traditional epoxy powders: b improved colour stability b wider operating temperature range. Mechanical properties of enclosures Static load on doors, wall-mounted and floor-standing enclosures and cubicles Floor-standing enclosure Wall-mounted enclosure Floor-standing enclosure door Wall-mounted enclosure door 64 kg 48 kg 4 kg 4 kg Mechanical properties of powder coated surfaces Test conditions Test piece made of 1 mm thick steel sheet, degreased, iron phosphated, final rinsing with 100000 W cm DI water, 15 microns of anti-corrosion electrophoresis treatment and 35 microns of powder paint. Adhesion (cross-hatch and pull-off) Impact strength (1) Mandrel bending test (2) Persoz hardness class 0 required > 1 kg/50 cm < 10 mm 300 s (ISO 2409) (ISO 6272) (ISO 6860) (ISO 1522) (1) No cracking of the paint film after dropping a weight of one kilogram on the test piece from a height of 50 centimetres. (2) Film cracks over a length of 10 millimetres maximum. Artificial ageing test on powder coating Test conditions: two tests carried out on the same 1 mm thick steel sheet test piece. b cyclical damp-heat test: v as per standard IEC 68-2-30 - six 24-hour cycles at temperatures higher than 40 °C b continuous resistance to neutral salt mist: v the tests were carried out over a period of 400 hours, far more than the 48 hours required by the standard for indoor installations v as per standard IEC 68-2-11 and ISO 7253 - 400 hours without blistering for normal surface on test piece - 250 hours for a scratched surface. Evaluation of corrosion as per ISO 4628: b adhesion: class y 1 b blistering: degree 1 dim.1 b rusting: Ri 1 b cracking: class 1 b flaking imp. 1 dim. 1 b propagation of corrosion under scratch with respect to the scratch axis: 3 mm max. Chemical properties of powder coating Tests carried out at ambient temperature on phosphated test pieces coated with a 150 to 200 micron film. Test duration (months) Acids Bases Water Solvents Acetic Sulphuric Nitric Phosphoric Hydrochloric Lactic Citric Soda Ammonia Distilled water Seawater Tap water Diluted bleach Petrol High alcohols Aliphatics Aromatics Ketones, esters Tri-perchlorethylene Concentration 20 % 30 % 30 % 30 % 30 % 10 % 10 % 10 % 10 % 2 Film intact. Film damaged (blisters, yellowing, loss of shine). 158 4 6 8 10 12 Additional information Thermal management of switchboards Thermal characteristics General A switchboard is designed for operation under normal ambient conditions. Most devices do not operation correctly outside a temperature range of -10 and + 70 °C. It is therefore important to maintain the switchboard internal temperature within this temperature range by: b correctly sizing the switchboard during design b correcting the temperature using suitable means. Management of the internal temperature Cooling There are a number of way to dissipate heat from the switchboard. The drawings below present the various means. DD383635 Forced-air ventilation DD383634 DD383633 Convection IP > 31 IP y 31 Ensured naturally in Prisma Plus enclosures. Forced convection and cooling DD383638 DD383637 Forced-air ventilation with air-air exchanger IP y 54 Using fans, it significantly increases the thermal capacity of an enclosure. ? IP > 31 On special request. IP > 31 b For these extreme cases, many installers prefer to set up the switchboards with other electrotechnical and electronic devices in air-conditioned electrical rooms. Heating The means employed to raise the internal temperature in a switchboard is a resistorbased heater, used to: b avoid condensation by limiting variations in temperature b ensure that the switchboard does not freeze. 159 Additional information Thermal characteristics Thermal management of switchboards General DD381401 Calculation of the internal temperature Calculation of the temperature is the means to check that the enclosure can evacuate the dissipated power of the installed devices. DD383636 Important note Correct thermal management of the switchboard depends on compliance with the installation requirements for the distribution system (power circuits). Incorrect installation will have major consequences on the connected device, but almost none on the internal temperature of the enclosure. Once the circuit has been correctly sized, it is necessary to check whether the assembly (devices + distribution system + cables) have a level of dissipated power P(W) y the P(W) that the enclosure can handle. Method defined by IEC 890 technical report This IEC guide for switchboards proposes a calculation method to determine three levels of internal temperature, depending on the dissipated power of the devices and distribution blocks installed in the switchboard. Users can consult this document when it is necessary to determine precisely the internal temperature in view of optimising the switchboard. On request, Schneider Electric can carry out a thermal study to check that the installed assembly and the thermal capacity of the enclosure are compatible. DD382422 Comparative method A number of qualified and tested configurations serve as the basis for indicating the thermal capacity of Prisma Plus enclosures. This is en empirical means to check whether the dissipated power of the desired configuration is close to that of a tested configuration. Method using charts taking into account enclosure characteristics To speed up calculations, Schneider Electric produces charts based on the company’s experience and a number of assumptions on the installation. They can be used sufficiently precisely to determine the variations in temperature and the dissipated-power levels for the different types of wall-mount enclosures, floor-standing enclosures and cubicles. 160 Additional information Thermal management of switchboards Thermal characteristics Comparative method Comparative method Pack enclosure, 3 rows, IP30 Diversity factor: 0.7 Ambient temperature around the switchboard: 35 °C P(W) = 95 W DD384080 You will have no problems with your switchboard if: b the volume of the enclosure is greater than that of the tested enclosure with a similar assembly b the P(W) of the installed assembly is less than the P(W) of the tested configuration in the same size enclosure. C60N or IC60N 40 A C60N or IC60N 32 A C60N or IC60N 25 A C60N or IC60N 25 A DD384081 C60N or IC60N 40 A Wall-mounted enclosure, 23 modules, IP30 Diversity factor: 0.7 Ambient temperature around the switchboard: 35 °C P(W) = 170 W C60N or IC60N 20 A NSX250N C60N or IC60N 63 A C60N or IC60N 40 A C60N or IC60N 50 A C60N or IC60N 20 A C60N or IC60N 32 A C60N or IC60N 50 A C60N or IC60N 20 A C60N or IC60N 40 A C60N or IC60N 32 A C60N or IC60N 20 A C60N or IC60N 20 A C60N or IC60N 25 A 161 Additional information Thermal management of switchboards Thermal characteristics Comparative method Comparative method Wall-mounted enclosure, 23 modules, plain door, IP30 Diversity factor: 0.7 Ambient temperature around the switchboard: 35 °C P(W) = 200 W DD383955 You will have no problems with your switchboard if: b the volume of the enclosure is greater than that of the tested enclosure with a similar assembly b the P(W) of the installed assembly is less than the P(W) of the tested configuration in the same size enclosure. NSX400 NSX125N Floor-standing enclosure, 33 modules, IP30 Diversity factor: 0.7 Ambient temperature around the switchboard: 35 °C P(W) = 270 W DD384082 NSX100N NSX630N NSX250N NSX250N C60a or IC60a 10 A 162 C60a or IC60a 10 A C60a or IC60a 10 A C60a or IC60a 10 A C60a or IC60a 10 A Additional information Thermal management of switchboards Thermal characteristics Example DD382423 Once the dissipated power of the devices has been determined and the enclosure with its IP selected, transfer the results (sum of the dissipated power and width of the device zone) to the chart corresponding to the enclosure IP. Draw a line parallel to the others on the chart and read the corresponding difference in temperature. For the given example, the heat rise is 22 °C at mid-height in the enclosure. The internal temperature = external temperature + heat rise = 35 °C + 22 °C = 57 °C 57 °C < 60 °C stipulated by the standard, i.e. the result is acceptable for an IP3 cubicle. This gives roughly: Internal temperature = 60 °C at mid-height in the enclosure for a low IP value. = 70 °C at mid-height in the enclosure for a high IP value. 163 Additional information Thermal management of switchboards Thermal characteristics Charts Quick calculation charts for internal temperatures The indicated internal heat rise is that measured at mid-height in the enclosure. IP43 wall-mounted enclosure DD382433 DD382432 IP3X wall-mounted enclosure IP3X floor-standing enclosure IP43 floor-standing enclosure DD382435 Test conditions: 600 mm wide enclosure mounted directly on wall without fixing lugs. DD382434 Test conditions: 600 mm wide enclosure mounted directly on wall without fixing lugs. Test conditions: 600 mm wide enclosure on floor against a wall. Test conditions: Mounted on wall with fixing lugs or on mounting uprights. DD382436 IP55 wall-mounted and floor-standing enclosures Test conditions: 600 mm wide enclosure mounted directly on wall without fixing lugs or mounting uprights. 164 Additional information Thermal management of switchboards Thermal characteristics Ventilation Switchboard ventilation The air enters the lower section via the fans and exits the upper section: b through a ventilated roof b or through a ventilation opening. The air throughput of the fans is determined by the equation: P D = 3 1 ×⎛⎝ ------- – KS ⎞⎠ DT The chart below can be used to determine the necessary throughput, based on the dissipated power, the difference in temperature (internal - external) and the exposed surface area of the enclosure. Example Consider an IP3X cubicle, 650 mm wide and 400 mm deep, containing components (devices, connections, busbars, etc.) dissipating 1000 W. The ambient temperature around the cubicle is 50 °C. Given that the average temperature at mid-height should not exceed 60 °C, the difference in temperature DT is equal to 60 - 50 = 10 °C. The exposed surface of the cubicle (non adjacent to a wall or other cubicle) is 4.46 m². (back = 1.3 m², front = 1.3 m², roof = 0.26 m², side panels = 1.6 m²). What is the necessary throughput of the ventilation system? The throughput can be calculated as: 1000 D = 3 1 × ⎛⎝------------- – 5 5 × 10 46 ⎞⎠ DD381391 D = 234 m3/h. In the range of Prisma Plus accessories, select a system with a throughput of 300 m3/h. Calculation data P : power dissipated by the devices, connections and busbars (in Watts) Pr : power of the heating resistor (in Watts) Tm : maximum internal temperature in the device zone (in °C) Ti : average internal temperature (in °C) Te : average external temperature (in °C) DTm= Tm T e DT = Ti Te S : total free surface area of the enclosure (expressed in m2) K : thermal-conduction coefficient of the material (W/m2 °C) K = 5.5 W/m2 °C for painted sheet metal D : ventilation throughput (in m3/h) – – Note: The dissipated power of each device is provided by the manufacturer. Add approximately 30 % to account for the connections and the busbars. 165 Additional information Thermal management of switchboards Thermal characteristics Heating Switchboard heating The heating resistor, placed in the bottom of the switchboard, maintains the internal temperature 10 °C higher than the external temperature. When the switchboard is not in operation, the heater compensates the dissipated power normally emitted by the switchboard. The power of the heating resistor is calculated: b using the equation: Pr = (DT x S x K) - P b or using the charts below, based on the exposed surface area of the enclosure and the desired difference in temperature. DD381788 Chart to determine the heating resistor for small wall-mounted enclosures (exposed surfaces y 1 m2) DD381789 Chart to determine the heating resistor for all types of enclosures Calculation data P : power dissipated by the devices, connections and busbars (in Watts) Pr : power of the heating resistor (in Watts) Tm : maximum internal temperature in the device zone (in °C) Ti : average internal temperature (in °C) Te : average external temperature (in °C) DTm= Tm T e DT = Ti Te S : total free surface area of the enclosure (expressed in m2) K : thermal-conduction coefficient of the material (W/m2 °C) K = 5.5 W/m2 °C for painted sheet metal D : ventilation throughput (in m3/h) – – Note: The dissipated power of each device is provided by the manufacturer. Add approximately 30 % to account for the connections and the busbars. 166 Additional information DD383904 Practical information Tools required for mounting and connection b Vacuum cleaner to clean the switchboards b Ratchet wrench with sockets b Torque wrench with sockets and ring bits to tighten the electrical connections to the correct torque (max. torque 50 Nm) b Open-ended spanners (15 to 27 mm) b Electrician's knife b 7, 8, 10, 13, 16, 17 and 19 mm sockets b Bit holder socket b 4, 5, 6, 8 and 10 mm hexagonal-head bits b Pozidriv no. 1, 2 and 3 bits b Rubber mallet b Level b Measurement and inspection tools and instruments b Drill b Semi-circuit nosed pliers b Cable-tie pliers b Wire stripper b Crimping tool b Diagonal cutter b Wire cutters b Flat-nosed pliers b Bit holder for screwdriver b Extension b Electric saw b Jig saw b Clamp for cubicle alignment b Buzzer or tester b 3, 5, 4, 5.5 and 8 mm flat screwdrivers b Posidriv no. 2 crosshead screwdriver (to mount handle) b Hydraulic jacks that can be operated in horizontal position to lift cubicles and move them sideways if necessary b Coloured, indelible and temperature resistant acrylic varnish b Electric screwdriver 167 Notes 168 35, rue Joseph Monier CS 30323 F- 92506 Rueil Malmaison Cedex RCS Nanterre 954 503 439 Capital social 896 313 776 www.schneider-electric.com DESW015EN As standards, specifications and designs change from time to time, please ask for confirmation of the information given in this publication. This document has been printed on ecological paper. Publication: Schneider Electric Industries SAS Design/Layout: Emmanuel Froger / SEDOC Printed: Altavia Connexion - Made in France 10-2011 © 2011 - Schneider Electric - All rights reserved. Schneider Electric Industries SAS
