Enamel - City of Sanford

/r
PRODUCTDATA
\11-
SII-ATHANE
INT.- EXT. ALKYD GLOSS
qN_AI4.Er
Series
PRODUCTDESCRIPTION:
A superior quality interior-exterioralkyd gloss enamer
combining the
durability, gloss retention and color permanencyassociateo
*itn
urethane and siricone resins. when used in conjunction with
BRUNTNG
Silathane Rust Proof Metar primers, it provides exceilent protection
for
equipment, machinery, ironwork and tools. (Not for uso on
aluminum
siding).
PRODUCTFEATURES:
I A tough,
durablecoating
' High gloss
sheen
' Excellent
flow and leveling
' Good gloss
retention
' Resistant
to dirt collection
r Free of lead
and mercury
e Good tint retention
'Easy brushing
' Safe for toys
' USDA approved
for indirect
food contact.
RECOMMENDED
USES:
' Exterior
wood trim and doors; interiorwood trim
' Properlyprimed
metal and ironwork
+ Floors and
decks (add grit where foot traffic is expectedf
' Shops
and manufacturingfacilities
' Machinery,
equipment,storagetanks
+ Primed
metal and wood cabinets;paintedmetal siding
' Toys, room
and patio furniture;boats
' Previouslypainted
concrete or brick
' while not
specificaily formurated for use as the originarfinish
appried
at the factory to ind.ustrialor consumer products,
many OEM applicatrons are quite suitabre.consurt your BRUNTNG
RepresentatJeas to
suitabilityof purpose.
COLORS:
White. Hi-HideWhite (tintable),severalready
mixed colorsand a wide
variety of attractive shadesproducedby tintrng
custom cororbases.
SURFACEPREPARATION:
In all instances,mildew must be removed
before paintingby scrubbing
an affected area with a medium sort brush
and the suggesteddetergent/
bleach solution noted on the back side of this
sheet.
S t e p 1 . G e n e r a l l ya, l l s u r f a c e sm u s t b e c l e a n .
dry and freeof dirt,
grease and excessivechalk. Removepeeling
or flakingpaint
by sanding,scraping,wire brushingor water
blasting.Dull
glossy surfacesby sanding.
TECHNICALDATA:
PRODUCTCODE: 520-00
GENERICTYPE:Soya Linseed,
SiliconeModified
Alkyd Resin
G L O S S :9 0 M l N . @ 6 0 o
D R Y I N GT I M E :@ 7 7 o F . - S 0 % R . H .
Touch (hrsl: 2
Recoat(hrsl
: Overnight
WT/GAL: 9.3 LBS
VISCOSITY:75-80 KU
FLASH POINT: 'l04oF. (TCC)
PERCENTSOLIDSBY WT: S9.9%
PERCENTSOLIDS BY VOL: 42.8o/o
PERCENTVEHICLE(SOLIDSI
BY WT:34.S%
PERCENTPIGMENTBY WT: 24.4%
WET FILM THICKNESS:3.2 mils
D R Y F I L M T H I C K N E S S':t . 4 m i t s
THINNING/CLEAN-UP:
MineratSpirits
V O C : M a x . 2 . 6 l b s / g a l . ,4 3 5 g m s / L
As of I I /91 , this product complics with cuncn
VOC regulatiorc in all statcslareas ctccpt New
Yor*, City (ttsc 7154 or 5324), NJ.(usc 7IS-&
or 532-OO),CA.(ue 7154 or 53240), TX.(rcc
715-0Oor 53240) and Maricopa, AZ(usc 7IS4O
or 532-0O)
NEW WOOD: Reler to Step 1. lnterior wood
surfacesshouldbe primed
with BRUNINGSitathaneAlkyd Enamel
Undercoat ISZO-121.Exterior
wood surfaces should be primed with BRUNING
CarriageHouseExterior
A l k y d p r i m e r( 3 0 0 - 2 9 1 .
08032-32-4
Proprietary
PREVIOUSLYPAINTEDWOOD: Surfaces
in good conditiondo not
require priming - iust right sanding.rf repaintlo
surfacesare in bad
c o n d i t i o n ,a p p l y a c o a t o f p r i m e ra f t e r
sanding.
13463-67-7
Proprietary
Proprietary
RIGHTTO KNOW INFORMATTON:
CAS No.
Inorodient
Mineral Spirits
Tall Oil Alkyd
Resin
TitaniumDioxide
Castor Oil Deriv.
Calcium Drier
j , : : , . , :1
.O'
I
i
*lt
METAL SURFACES:Clean thoroughly. remove
corrosiondeposits (rust. oxidation, etc.l and allow
to dry. Prime interiorferrous metal with BRUNING
SilathaneMetal Primers(520-131or (520-1.41.
Prime interior non-ferrousmetal with ERUNING
BLOCK-OUTll Acrylic Primer (235-OOl, BRUNING
Silathanell Acrylic Primer(532-131or ERUNING
Silathanell Mstal Primer(520-131.Prime exterior
f e r r o u sm e t a l w i t h B R U N I N G( 5 2 0 - 1 3 1o r ( 5 2 0 - 1 4 1 .
Prime exterior non-ferrousmetal with BRUNING
1 5 2 0 - 1 3 11, 2 3 5 - 0 0 )o r ( 5 3 2 - 1 3 1 .
MASONRY SURFACES:New masonry must be
thoroughly cured at least 60 days, then painted
with BRUNINGPacon Supreme Epoxy Masonry
Surface Conditioner(390-121before applying
1520-001.Previouslypainted masonry and brick
surfacesmust be clean, dry, free of dirt and
mildew before painting.
APPLICATION:
BRUNINGSilathane Int./ Ext. Alkyd Gloss Enamel
(520-001may be applieddirectly from its container
by brush, roller or airless/conventional
spray. Stir
thoroughlybefore using. For increasedprotection,
a second coat may be applied {without any surface
pregl after the previouscoat has dried overnight.
Apply a full, generouscoat spreadingevenly to a
uniform film thickness.Avoid painting when air,
(continuednext columnl
WARNING
product or surfacetemperatureis below 4OoF.
AIRLESSSPRAYDATA:
Spray equipmentmust be operatedwith care in strict
accordancewith manufacturer'sinstructions.When
spray applying,wear approvedrespiratoryand eye
protectionand protectiveclothing.
Atomizationpressureand tip size will vary depending
upon the specificequipmentused, the viscosity of the
coating and the air temperatureat time of application.
Equipmentthat will maintain an atomizing pressureof
1 7 5 0 - 1 9 5 0P S Ii s r e c o m m e n d e dA. s p r a y t i p s i z e o f
. 0 13 " t o . 0 19 ' i s s u g g e s t e d .
--r
RECOMMENDED
SPREADINGRATE/ THINNING:
Up to 500 sq. lt. per gallon dependingupon the type
of surface,method of applicationand climatic conditions. On very porous surfacessuch as concrete and
cinderblock, expect about 300 sq. ft. per gallon.
Use product as supplied.lf required,may be thinned
sparinglywith mineralspirits not to exceed 1/2 pint per
gallon.
D R Y I N GT I M E / C L E A N - U P :
At77oF and 50o/orelativehumidity, this product dries
t o t h e t o u c h i n 2 h o u r s .A l l o w 1 2 - 1 6 h o u r s o r l o n g e r ,
dependingon temperatureand weather conditions,
before applyinga second coat.
Cleanbrushes,rollers,spray and other equipment
immediatelyafter use with mineralspirits.
COMBUSTIELELIOUIDAND VAPOR...CONTAINS
MINERALSPIRITS
VAPOR HARMFUL, MAY AFFECT THE BRAIN OR NERVOUSSYSTEM CAUSING DIZZINESS.HEADACHE OR
NAUSEA. CAUSES EYE, SKIN, NOSE AND THROAT IRRITATION.NOTICE: Reports have associatedrepeated and
prolonged occupational overexposur€to solvents with permanent brain and nervous system damage. Intentional
misuse by deliberatelyconcentrating and inhalingthe contents may be harmful or fatal. Keep away from heat and
flame. USE ONLY WITH ADEOUATE VENTILATION. To prevent build-up of vapors and to avoid breathing vapors or
spray mist, opon windows and doors or use other m€ans to ensure lresh air entry during applicationand drying.
lf you experience eye watering, headaches or dizziness, increase fresh air or wear respiratory protection
(NIOSH/MSHA TC 23C or eguivalontl or leave th6 arsa. Close container after each use. Avoid contact with
eyes, skin and clothing. Wash thoroughly after handling.
FIRST AID: lf breathing difficulties occur. leave the erea to obtain fresh air. tf difficulty conrinues, get immediare
medical attention. In case of eye contact, f lush immediatelywith plenty of water for at least 15 minutes and get
medical attention. For skin contact, wash thoroughly with soap and water. lf swallowed, do not induce vomiting.
Call physician immediatelv.
KEEP OUT OF THE REACH OF CHILDREN
MILDEW REMOVAL...- (Doublebteachamountif mitdewis severe)
CAUTION: A DETERGENT/ BLEACH SOTUTION IS IRRITATINCTO EYES AND SKIN AND SHOULD BE.KEPT OUT OF THE
REACH OF CHILDREN.Weer goggles, rubber gloves end protective clothing during preparationand application: Read detergent
and bloach containar'labsls before mixing. lf thers are ammonia or ammonium containing compounds in the dotergont. do not
add to tho btoach as harmful vopors may bo formod. lN cAsE oF coNTAcT. FLUSH|MMEDIATEIY wlTH pLENTy oF WATER
AND CONSUTTA PHYSICIAN.
To 3 qu€rts warm w€ter, add 1 quart liquid bleechcontaining5% sodium hypochlorite(Example:CHLOROX).Add % cup nonphosphate typs deteroent (Example: 4O9, Mr. Cleqn; etc:l, rinse the treated area with f resh water and allow to dry before
repainting-Ropaintwithin ono month of bloachingto,prevent possibto6poro rogeneration.
Tothebestofourknow|edgs.th€technica|.ffiandaccUrateatthedateofissuancebutaresubiect
to change without prior notice. We guarantee our product
to conform to BRUNING'Sspecifications.WE MAKE NO OTHER
W A R R A N T Y O R G U A R A N T E EO F A N Y K I N D , E X P R E S SO R I M P L I E D ,I N C L U D I N GM E R C H A N T A B I L I T Y
A N D F I T N E S SF O R
PARTICULARPURPOsE-Liability, if any is limited to replacem€nt
of the product or refund of the purchase price. LABOR oR
C O S T O F L A B O R A N D O T H E RC O N S E O U E N T I AD
L A M A G E SA R E H E R E B YE X C L U D E D .
2Ig2
f'