Tigress Catalog - Eastern Metal Supply

Transcription

New Products
MANUALLY ADJUSTABLE
ANTENNA MOUNT
PATENT PENDING
• Features a bottom mounted crank
assembly for ease of deployment fore
and aft.
• Simply push up on the handle to release
the gears and turn 12 times to complete
deployment of your antenna.
• Then simply pull handle down to lock
into place.
• Adjustable up or down motion eliminates
climbing the gunnel to adjust your
antenna.
• Fits all prepared t-tops with 3” Mounting
Hole. Fits Hard tops up to 2 1/2” thick.
88810 - Manually Adjustable Antenna Mount
MANUALLY ADJUSTABLE
RUNNING LIGHT MOUNT
• Features a bottom mounted
crank assembly for ease of
deployment fore and aft.
• Simply push up on the handle
to release the gears and turn
12 times to complete deployment
of your running light.
• Then simply pull handle down
to lock into place.
• Adjustable up or down motion
eliminates climbing the gunnel to
adjust your running light.
• Fits all prepared t-tops with 3”
Mounting Hole. Fits Hard tops
up to 2 1/2” thick.
88811 Manually Adjustable
Running Light Mount
MANUALLY ADJUSTABLE
FLAG MOUNT
MANUALLY ADJUSTABLE
CENTER RIGGER MOUNT
deployment.
12 times to complete
deployment of your flag.
to lock into place.
• Adjustable up or down motion
eliminates climbing the
gunnel to adjust your flag.
deployment.
to complete deployment of your
center rigger to your preferred
angle.
to lock into place.
Flag Mount
www.tigressoutriggers.com
Center Rigger Mount
New Products
ELECTRONICALLY OPERATED
ADJUSTABLE ANTENNA MOUNT
Finally an Electronically Operated Antenna
Mount that allows the user to raise or lower
your antenna without ever leaving the console
of your boat.
PATENT PENDING
• Meticulous Engineering provides for
exact raising or lowering of your
antenna from the console of your boat.
• To raise and lower their antenna
simply press a switch.
• The powerful 12V motor drive allows
for the total deployment and/or
adjustment by simply pressing the
switch up for deploying or pressing
switch down for retrieval.
• Mounting Plate Size: 4” W x 8” L
Bolt pattern fits standard t-top
extrusions with a 3” X 5” standard
hole pattern
• Includes 12’ of wire from each holder.
• Units are supplied with a standard on
off on switch.
• Convenience, craftsmanship,quality
and performance will make these
products a prefered selection for all
Boaters and Sport- Fishermen.
88814 - Electronically Adjustable Antenna Mount
Also Available in Running
and Anchor Light
88815 - Electronically adjustable running and
anchor light mount
Table of Contents
Page 5
Page 6
Page 7
Page 8
Page 9
Page 10
Page 11
Page 12
Page 13
Page 14
Page 15
Page 16
Page 17
Page 18
Page 19
Page 20
Page 21
Page 22
Page 23
Page 25
Page 26
Page 27
Page 28
Page 29
Page 30
Electric Top Mounts
Manual Top Mounts
Top Mount Outrigger Holders
Gunnel & Side Mount, Outrigger
Holders & Accessories
Telescoping Outriggers
Telescoping & Fixed Outrigger
& Accessories
Top Mounts & Clamp-On Systems
Gunnel & Center Rigger Systems
Rigging Kits
Outrigger Snubbers & Accessories
Kites & Accessories
Kite Rod Holders & Accessories
Tigress Kite Set Up
Gunnel, Pivoting & Side Mount
Rod Holders
Blind, Mount, Round, Pivoting
& Oval Rod Holders
Economy Stainless Rod Holders
Clamp-On Rod Holders
Heavy Duty Bearing Style Hinges
Rod Holders Backing Plates
& Accessories
Pipe Size Chart
Rod Holder & Chair Accessories
Rod & Reel Hangers
Aluminum Rod Holders
Triple, Bolt-On & Transom Rod Holders
Hard Top Bushings & Washers, Cup
Holders & Back Rest Components
Breakaway Pins, Boss & Mounting Angles
Page 31
Page 32
Page 33
Page 34
Page 35
Page 36
Page 37
Page 38
Page 39
Page 40
Page 41
Page 42
Page 43
Page 44
Page 45
Page 46
Page 47
Page 48
Page 49
Page 50
Sleeves, Pipe Aligners, Antenna Ratchets,
Mounting Pads & Bow Rail Components
Ski & Wakeboard Tower Components
Foot Rest Hardware, Ear Mounts,
Folding Bench Seat, Hinge Brackets
& Alignment Pins
Female & Male Pins, Half Pins
& Tower Boss
Fiberglass Boxes & Hard Tops
Round Polished Pads
Round High Polished Pads &
Round Brushed Pads
Round Mill Finish Pads
Rectangular Polished, High Polished
& Brushed Pads
Miscellaneous Pads
Specialty Pads
Inline & Hand Rail LED Lighting
Clamp-On LED Lighting
LED Strip Lighting
Bracket Mount, Center Mount & Weld
Mount LED Lighting
Marine Lights
Polished & Brushed Bright Dipped
Anodized Pipe
Polished Bright Dipped Anodized Pipe &
Mill Finish Pipe
Bright Dipped Anodized Drawn Tube,
Stainless Steel Tube & Oval Tube
Polished Bright Dipped Anodized Angle,
Tees, Square & Rectangular Tube & Flat Bar
Polished Bright Dipped Oval Tube,
Misc. Extrusions & Marine Grade Sheet
“TIGRESS® QUALITY” - ACCEPT NO IMITATIONS
Since our inception 24 years ago, Tigress’ mission has been to raise the bar for innovation, quality, ease of use, and
convenience on our products offered to the salt water sports fishing industry. All Tigress® Aluminum Outriggers are
constructed of cold drawn aluminum for maximum strength and durability. We then use a state of the art anodizing process
to protect & enhance our products. Every accessory is constructed of the best materials to give the maximum service and
life. Tigress® uses only 300 & 316 stainless steel in every rod holder or outrigger holders.
“SAY HELLO TO SIMPLICITY”
Our Patented TigerShark I Electronically operated LineRigger and our TigerShark II Manually Operated LineRigger offer
the user the “Simplicity” of deploying their outriggers both up and out to the fishing position in one step. A simple push of
the control switch for the electronic version or a few cranks of the handle for the manual version and you are fishing.
Tigress® Tiger Fish and Tiger Fish II Top Mount Outrigger Holders allow the user to deploy his outriggers from the safety
and convenience of his console. No more standing on the gunnel in heavy seas trying not to fall overboard while deploying
your outriggers. Simply pull down the handle and move your outrigger to select one of multiple fishing positions. We have
and will continue to expand our quality offerings of fine products and accessories making the Tigress® Product Line of
Outriggers and Gear the Standard of Quality and Excellence.
Electric Top Mounts 5
IT’S ELECTRIC
TIGERSHARK LINERIGGER®
TOP MOUNT OUTRIGGER HOLDERS
TIGERSHARK I - SAY HELLO TO SIMPLICITY!!
THE SIMPLICITY OF PRESSING A SWITCH AND YOU’RE FISHING!!
• The TigerShark I LineRigger® is the first electronically operated
top mount outrigger holder offered in the market.
• Meticulous engineering provides exact electronic deployment of your
outriggers from your console.
• The powerful 12V motor drive allows for the total deployment and/or
adjustment by simply pressing the switch up for deploying or
pressing switch down for retrieval of your
outriggers.
• Fits all prepared t-tops with 3” Mounting Hole.
• Mounting Plate Size: 4” W x 6” L.
• Includes 12’ of wire from each holder.
• Units are supplied with a standard dual rocker
switch panel, when activated simultaneously
raises and deploys your outriggers to the fishing
position.
• Convenience, craftsmanship, quality and
performance will make the TigerShark a Top
Selection for the Sports-Fisherman.
UP & OUT
IN ONLY
88800 - 1 1/2” Electric Top Mount
25 SECONDS
6 Manual Top Mounts
MANUAL MODEL
TIGERSHARK LINERIGGER®
TIGERSHARK II & III- SAY HELLO TO SIMPLICITY!!
THE SIMPLICITY OF TURNING A HANDLE AND YOU’RE FISHING!!
• Offer complete manual outrigger deployment
from your console.
• Allows for adjustments to clear low obstacles
or quickly adjust your outriggers to maximum
bait spread.
• Up and out motion eliminates climbing the
gunnels to adjust your outriggers.
• A simple turn of the handle does it all, total
deployment and total position adjustment.
• Meticulous craftsmanship, quality,
performance and convenience will propel
these TigerShark manual units to a top
selection for the Sports Fisherman.
88802 - 1 1/2”Manual Top Mounts for Soft Tops
88803 - 1 1/2” Manual Top Mounts for
Hard Tops up to 2 1/2”
THE NEWEST OF OUR TIGERSHARK SERIES
OF TOP MOUNT OUTRIGGER HOLDERS.
• Features a bottom mounted crank assembly
for ease of deployment.
• Simply push up on the handle to release the
gears and turn 14 to 17 times to complete
deployment of your outriggers.
• Then simply pull handle down to lock into place.
• Simultaneous up and out motion eliminates
climbing the gunnels to adjust your outriggers.
Fits Hard tops up to 2 1/2” thick.
• Allowing for the lowest profile under your t-top
or hard top of any top mount outrigger holder in
the industry.
88805 - 1 1/2” Manual Top Mounts Designed
for Hard Tops and Soft Tops
Top Mount Outrigger Holders 7
TIGERFISH I & II
ROD HOLDER/OUTRIGGER HOLDERS
Patent # US 7,197,845 B2
Patent # US 7,296,377
1 1/8” AND 1 1/2”
• Constructed of aluminum and stainless steel or
all stainless steel with self-lubricating bearings
for ease of deployment and years of durability
and use.
• No more climbing your gunnel in heavy seas to
deploy your outriggers.
• Deploys simply from your console.
• Heavy duty isolator pad included with stainless
steel model.
Parts
Material
Holder Size
88960
Adjustable
Stainless
1-1/8”
88950
Adjustable
Alum/SS
1-1/2”
T-TOP ADJUSTABLE CLAMP-ON
Patent # US 7,296,377
• Simply drill 1/4”
hole into the IPS
schedule pipe of
your t-top and
clamp-on.
Parts
Clamp Size
Holder Size
88965
1-5/16”
1 1/8”
88966
1-11/16”
1 1/2”
88967
1-15/16”
1 1/2”
• Put absolutely no more holes in your t-top or the
gunnel of your boat.
• Simply place into your existing Heavy Duty Cast
stainless rod holder when outriggers are needed.
• When outriggers are not in use simply remove holders
and your existing cast rod holder is usable again.
Parts
Base
Tube
Holder Size
88968
1 5/8”
16”
1-1/8”
88969
1 5/8”
16”
1-1/2”
TOP MOUNT WEDGES
Angular adjusting wedges
to straighten the top
mount in installation
allowing for less stress
on the top and smoother
deployment of your
outriggers.
Parts
Degree
88934
7°
88936
9°
88938
11°
4”x 6”
& Side Mount,
8 Gunnel
Outrigger Holders & Accessories
OUTRIGGER HOLDERS AND
REPLACEMENT TUBES
WISH BONE HOLDERS
FABRICATED
CUT BASE
TUBES
Gunnel Mount
Size
Material
88500
1 1/8” ID
Fabricated 304
88502
1 1/8” ID
Cast 316
88506
1 1/2” ID
Cast 316
88504
1 1/8” ID
Fabricated 304
88505
1 1/8” ID
Cast 316
88508
1 1/2” ID
Cast 316
88501
1 1/8” ID
Cast Base
88503
1 1/8” ID
Cut Base
88507
1 1/2” ID
Cast Base
Side Mount
Replacement Tubes
Cast 316
CAST BASE
TUBES
1-1/2” AND 2” LARGE SIDE MOUNT
OUTRIGGER HOLDERS
• For extrusions.
• Constructed of Heavy Cast 316 stainless steel
with 18” polished stainless steel tube.
Parts
OD
ID
88510
2”
1-7/8”
88511
1-5/8”
1-1/2”
CENTER RIGGER CLAMP-ON
88150 - Clamp-On Center Rigger Holder
1-5/16” IPS Pipe Clamp with 1 1/8” Holder
OUTRIGGER MOUNTING PLATE
BACKING PLATES
B
• Gunnel mount and side mount backing plates
• Made of heavy gauge stainless steel
• Please use with Part #’s as follows:
• Sized for cast outrigger holders only.
Gunnel Mount
Side Mount
88502-1 with 88502
88505-1 with 88505
88506-1 with 88506
88508-1 with 88508
OOMP-20 - Brushed Oval Outrigger Mounting Plate x 20”
OOMP-30 - Brushed Oval Outrigger Mounting Plate x 30”
Custom sizes cut to your specifications.
(minimum quantity required)
Telescoping Outriggers 9
TIGRESSTRACK® PREMIUM
TELESCOPING ALUMINUM
OUTRIGGER POLES
EXCALIBER 100% CARBON GRAPHITE
TELESCOPING OUTRIGGERS
& CENTER RIGGER
PATENT
#7,025,015 B2
• Featuring our Patented Tigress Track® Internal
Tracking System. “To Always Line Up And
Never Miss The Hole”.
• Constructed of cold drawn aluminum, anodized
inside and out for overall durability and style.
• Available in 3 popular sizes and colors.
• Features stainless steel line guides, stainless
steel snap buttons and anodized aluminum
trim rings.
• Retract to under 6’ for Trailering, Bridges and
Storage.
• Includes a handy heavy duty mesh storage bag.
(Patent #7,025,015 B2)
• The First Telescoping Carbon Graphite
Outrigger available to the SportFishing
Enthusiast.
• Features our Patented Tigress Track® Internal
Tracking System. “To Always Line Up And
Never Miss The Hole”.
• Proprietary manufacturing process utilizes
multiple layers of carbon graphite and UV stable
epoxy tape counter wrapped using tension,
pressure, and cure time to create the strongest
weight to strength ratio possible.
• Lightest Telescoping Outrigger in the Industry.
Part
Length
Base OD
Color
88900
15’
1 1/8”
Black/Gold
88901
15’
1-1/8”
Silver/Black
88903
15’
1-1/8”
Blue/Gold
88904
15’ HD
1 1/2”
Black/Gold
88905
15’ HD
1 1/2”
Silver/Black
88906
15’ HD
1 1/2”
Blue/Gold
Part
Length
Base OD
Color
Style
88908
18’ HD
1 1/2”
Black/Gold
88976
18’
1-1/2”
Blk/Blk
Outriggers
88909
18’ HD
1 1/2”
Silver/Black
88976-1 9’
1-1/8”
Blk/Blk
Center Rigger
88910
18’ HD
1 1/2”
Blue/Gold
88976-2 9’
1-1/2”
Blk/Blk
Center Rigger
& Fixed
10 Telescoping
Outrigger & Accessories
CARBON GRAPHITE FIXED
• High Quality Fixed Carbon
Graphite Outriggers.
• Unique coupling system
made of anodized marine
aluminum with polished
stainless line guides fitted
to each coupler.
PREMIUM FIXED ALUMINUM
• High Quality premium
fixed outriggers.
• Both the Black/gold
and silver/black
models are
constructed of
anodized aluminum.
• Anodized trim rings
and stainless steel
line guides.
Part
Size
Base OD
Color
Part
Size
Base OD
Color
C l
88973
15’
1-1/2”
Black/Gold
88400
15’
1 1/8”
Black/Gold
88401
15’
1-1/8”
Silver/Black
88403
15’
1 1/2”
Black/Gold
88404
15’
1 1/2”
Silver/Black
88405
18’
1 1/2”
Black/Gold
88406
18’
1 1/2”
Silver/Black
TELESCOPING FIBERGLASS
• An economical alternative
ECONOMY FIXED ALUMINUM
to aluminum Outriggers for
18’ to 28’ boats.
• 15’ telescoping, three-section,
heavy duty fiberglass out
riggers feature heavy line
guides for easy rigging.
• Includes a vinyl bag for
storage.
• Retracts to less that 6’.
• Constructed of heavy duty
anodized aluminum with
nylon guide assembly and
stainless steel line guides
• Four section, screw together
assembly with black
anodized aluminum tip.
88220 15’
Base OD 1 1/8” Silver/Black
Part
Size
Base OD
Color
88200
15’
1-1/8”
White/Blue
OUTRIGGER ACCESSORIES
SORIES
88685 -15’ Outrigger Carry Bag
88685 -18’ Outrigger Carry Bag
88677 - Outrigger Standoff
TIGRESS TRACK® CENTER RIGGER
• Available in three colors and in 8’ with 1-1/8”
OD base.
• Combine it with our clamp-on center rigger
holder and our center rigger kit.
• For multiple lines in the water. Retracts to less to 5’.
88914 – 8’ Black/Gold
88915 – 8’ Silver/Black
88916 – 8’ Blue/Gold
• Stabilize your
outriggers in resting
position by simply
inserting into your
existing weld-on rod
holder and clipping to
your outrigger.
OUTRIGGER HOLDER REDUCERS
• Down size your outrigger holders
Part
OD
ID
88680
Reduce from 1 1/2” 1 1/8”
88681
Reduce from 1 5/8” 1 1/2”
88680-1 Reduce from 1 7/8” 1 1/2”
Top Mounts &11
Clamp-On Systems
TIGRESS II TRACK® PREMIUM
TELESCOPING SYSTEMS
TIGRESS I TRACK® PREMIUM
TELESCOPING SYSTEMS
1 1/8” TIGERFISH II T-TOP SYSTEM
• TigerFish II T-Top Holders
• Tigress Track® Telescoping Outriggers
• Premium deluxe rigging kit
• Black mesh carry bag for storage
• TigerFish I T-Top Holders
Part
Mount
Part
Length
Color
Mount
15’ HD
Black/Gold
88950
Length
Color
1 1/2” TIGERFISH I T-TOP SYSTEM
88900-1
15’
Black/Gold
88960
88905-1
88901-1
15’
Silver/Black
88960
88906-1
15’ HD
Silver/Black
88950
88903-1
15’
Blue/Gold
88960
88907-1
15’ HD
Blue/Gold
88950
T-TOP CLAMP-ON TELESCOPING SYSTEMS
Put absolutely no more holes in the gun whale of your boat.
• T-Top Clamp-Ons
Part
Clamp Size
Holder ID
Color
88965-00
1-5/16”
1 1/8”
Black/Gold
88965-01
1-5/16”
1 1/8”
Silver/Black
88966-00
1-11/16”
1 1/2”
Black/Gold
88966-01
1-11/16”
1 1/2”
Silver/Black
& Center
12 Gunnel
Rigger Systems
FIBERGLASS TELESCOPING
OUTRIGGER SYSTEMS
TIGRESS TRACK® CENTER RIGGER
SYSTEMS
Economy version of a telescoping outrigger
system.
• 1 1/8” Fiberglass poles
• 1 1/8” Fabricated flush mount outrigger holders
• Economy rigging kit
For multiple lines in the water.
• Clamp-on center rigger holder 1-1/8” OD base
• Tigress Track® Telescoping Center Rigger
• Center rigger kit
•Holder Sized To Fit 1-5/16” Schedule Pipe
Part
Length
Color
Mount
Part
Length
Color
Mount
88917
8'
Black/Gold
88150
88200-1
15’
White/Blue
88500
88918
8’
Silver/Black
88150
88201-1
15’
Black/Gold
88500
88919
8’
Blue/Gold
88150
ROD HOLDER/OUTRIGGER TELESCOPING SYSTEMS
Put absolutely no more holes in the gun whale of your boat.
• Rod Holder/Outrigger Holders
Part
Shaft OD
Holder ID
Color
88968-00
1 5/8”
1 1/8”
Black/Gold
88968-01
1 5/8”
1 1/8”
Silver/Black
88969-00
1 5/8”
1 1/2”
Black/Gold
88969-01
1 5/8”
1 1/2”
Silver/Black
Rigging Kits13
PRO CHOICE OUTRIGGING KITS
The Tigress® line of outrigger rigging kits features a great selection of kits to fit the needs of any
fisherman. Whether you have a 15’ skiff poles or 35’ double rigged tournament poles, Tigress® has a
rigging kit for you. All kits feature top quality materials and are ready to be installed. Each kit includes
clips, mounting hardware, cord, snubbers, glass rings or snaps & pulleys.
ECONOMY
DELUXE
Affordable kit designed for
small boat riggers up to 15’.
• Pair of high impact release clips
• Pair 1-1/4” cork stops
• Pair of glass ring snubbers
• Pair of eye straps with screws
•100’ nylon braid
F single rigged riggers up
For
tto 20’
• Pair of glass ring snubbers
• 4 leader snaps
88600 – White Nylon Braid
88600-1 – Black Nylon Braid
ELITE
88601 100’ Black Nylon Braid
88602 100’ of 400 Pound Black Mono & 4 Crimps
Top quality kit
• Pair of EZ release clips
• Pair of single swivel snubbers
• 4 leader snaps
88603-1 100’ of 400 Pound Black Mono & 4 Crimps
TRIPLE
DELUXE PRO
The pro’s choice
• Pair of stainless ring snubbers
• 4 leader snaps
88602-1 100’ Black Nylon Braid
88602-2 100’ of 400 Pound Black Mono & 4 Crimps
For triple rigging your outriggers. For rigging up to 35’
• 3 Pair of EZ release clips
• 3 Pair 1-3/4” cork stops
• Pair of triple swivel snubbers
•12 leader snaps
88606-1 300’ of 400 Pd. Black Mono,12 Crimps
CENTER RIGGER KIT
ULTIMATE
For double rigging your
outriggers. For riggers up to 22’.
• 2 Pair of EZ release clips
• 2 Pair 1-3/4” cork stops
• Pair of double swivel snubbers
• 8 leader snaps
88605 – 200’ Black Nylon Braid
88605-1 – 200’ of 400 Pound Black Mono & 8 Crimps
• High impact release clip
• 1-1/4” cork stop
• Glass ring snubber
• Eye strap with screws
• 2 leader snaps
COMPLETE TAGLINE KIT
88644 Tag Line Kit
88642 Tag Line Weight
• Hi-polished 316 stainless
steel tag line weight with
1/4” rubber bumper to
protect your boat
• 35’ of 400 pound black mono
• Cork stops
• 316 stainless steel snaps
• 2 No. 64 rubber bands
14 Outrigger Snubbers
& Accessories
PRO CHOICE SNUBBERS
A
B
A
B
C
C
D
D
E
E
F
F
G
G
H
H
I
I
K
J
J
K
L
L
M
M
88620
88624
88624-1
88624-2
88624-3
88624-4
88624-5
88624-6
88624-7
88628
88632
88632-1
88632-2
88632-3
88632-4
88632-5
88632-6
88632-7
88634
88635
88635-1
88635-2
88636
88636-1
88636-2
88636-3
88636-4
88636-5
88636-6
88636-7
88638
88639
SNUBBER ACCESSORIES
C
A
E
B
F
K
D
H
G
I
J
M
L
U
N
Q
S
O
P
R
T
12” Economy Snubber
16” Deluxe Snubber
6” Deluxe Snubber
6” Deluxe Snubber w/Plastic Snap
6” Deluxe Snubber w/Ball Bearing Coastlock Swivel
12” Deluxe Pro Snubber
16” Elite Snubber
6” Elite Snubber
12” Elite Snubber w/Plastic Snap
6” Elite Snubber w/Ball Bearing Coastlock Swivel
16” Elite Pro Snubber w/Stainless Snap
6” Extender Snubber
Ultimate Snubber
6” Ultimate Snubber
6” Ultimate Snubber w/Plastic Snap
6” Ultimate Snubber w/Ball Bearing Coastlock Swivel
16” Ultimate Pro Snubber w/Stainless Snap
18” Triple Snubber w/Stainless Snap
THE MOST COMPLETE LINE OF OUTRIGGER
ACCESSORIES IN THE MARKET PLACE
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
88650
88660
88664
88666
88667
88656
88695
88697
88657
88659
88630
88640
88641
88652
88654
88690
88670
88671
88672
88668
88669
88673
88674
Pair Glass Outrigger Rings
Pair Stainless Steel Rings
Pair 316 Stainless Snaps
Pair Nickel Plated Snaps
Pair Stainless Pad Eyes w/Stainless Screws
Pair Outrigger Release Clips
E-Z Outrigger Release Clips (black)
Portable Release Clip
Down Rigger Release Clip
Flat Line Release Clip
Single Stainless Swivel
Double Stainless Swivel
Triple Stainless Swivel
Pair 1 1/4” Cork Stops
Pair 1 3/4” Cork Stops
Pair 1 1/4” Black Plastic Stops
100’ 400lb. Test Black Mono (Dia. 2.2 mm)
100’ 300lb. Black Nylon Braid
100’ 375lb. White Nylon Braid
Antenna Flag Clip
Halyard Flag Clip
3/4” Outrigger Guide Replacement (#88220)
7/8” Outrigger Guide Replacement (#88220)
Kites & Accessories15
Bite-This®
HI-VELOCITY KITES
Bite-This®
HI-PERFORMANCE KITES
88611
88611-1
• The Ultimate High Performance fishing kite. • This particular kite model will fly
• Will exceed all of your expectations and fly
steady in winds of 15 mph and up.
steady in all winds from 5 - 15 mph with a
• 4 holes in the custom fabric
simple adjustment to the bridle, eliminating
body to allow for passage of air
the need for different kites for different winds.
thru the face of the kite allowing
• Light weight spars are constructed of
it to fly at higher velocity winds.
100% carbon graphite.
• Light weight spars are constructed
of 100% carbon graphite.
88655
KITE KIT :
(2 CLIPS, 2 WIND-ON SWIVELS
& 1 COASTLOCK SWIVEL)
88658-7 KITE RELEASE CLIP
(NO WIRE) MEDIUM HOLE
88658-8 KITE RELEASE CLIP
88655-1 CLIP KITE KIT
(NO WIRE) LARGE HOLE
(3 CLIPS, 3 WIND-ON SWIVELS
1 COASTLOCK SWIVEL)
KITE RELEASE CLIP
88661
5/16” CERAMIC KITE RINGS
(8 EACH)
88658-1 KITE CLIP W/SMALL DIAME-
88662
1/2” CERAMIC KITE RINGS
(8 EACH)
88962
SMALL KITE LINE MARKERS
(NOT WEIGHTED)
88963
MEDIUM WEIGHTED KITE
LINE MARKERS
88964
LARGE WEIGHTED KITE
LINE MARKERS
88658
TER WIRE & WIND-ON SWIVEL
88658-2 KITE CLIP W/MED DIAMETER
WIRE & WIND-ON SWIVEL
88658-3 KITE CLIP W/LARGE DIAME-
TER WIRE & WIND-ON SWIVEL
88658-6 KITE RELEASE CLIP (NO
WIRE) SMALL HOLE
Rod Holders
16 Kite
& Accessories
KITE FISHING ROD HOLDER ARRAYS
TRIPLE KITE ROD
FIVE BANGER ALUMINUM
• Rod holder is used for 1 kite rod
and 2 additional rods to increase
your rod storage capacity and
keep them up and out of the way.
• Constructed of Cold Drawn
Anodized Aluminum.
• Available in either bent butt or
straight.
• Tube ID 1 5/8 “ Base OD 1.49”.
• Designed to increase your rod
storage capacity from 1 to 5 and
keep your fishing rods in easy
reach.
• Constructed of cold drawn high
polished anodized aluminum.
• Tube ID 1 5/8” Base OD 1.49”.
8
88157
Straight Butt
88157-1 Bent Butt
8
8
88156
Bent Butt Brushed
88158 Bent Butt Polished
8
88159 Straight Butt Polished
88153-2 Stainless Triple
DUAL KITE ROD
• Designed to increase your rod
storage capacity, or use one
side for your kite rod and other
for fishing rod.
• Constructed of Cold Drawn
Anodized Aluminum.
• Tube ID 1 5/8” Base OD 1.49”.
88154 Straight Butt Brush
KITE FLYING ACCESSORIES
8
88612
KITE LINE I ASSEMBLY
R
Ready Rigged Kite Lines
• 250ft. of 100 lb. Spectra line
• Three release clips •swivels on
reusable spool
8
88613 KITE LINE II ASSEMBLY
R
• Two release clips
• Swivels on reusable spool
88665 KITE RING
ASSEMBLY
88658-9 KITE SPRING
RELEASE CLIP
Clips onto your kite lines
to adjust space between
clips
8
88614 KITE LINE III ASSEMBLY
R
• Two release clips
• Swivels on reusable spool
88678 PLANER RELEASE
ASSEMBLY
• Use with planer provides a
quick release and allows you
to free-fight the fish.
• Includes 36” of 480lb test
cable, release clip & heavy
duty ball bearing snap
swivels.
8
88616
KITE LINE MARKER TAPE
UV Resistant kite line tape, an
economical convenient alternat to weighted kite line markers.
tive
Made in USA
88615 HELIUM BALLOONS
Ideal for adding that extra lift to kites
on those light wind days or used on
their own when there is no wind.
2 balloons with 3 clips. Made of 100%
pure latex. Biodegradable
How To Set Up Your Tigress Kite
Tigress by popular demand has put together the most comprehensive line of kite
fishng products available to the sport-fishing industry.
From a single HI-performance kite for all winds from 5 - 15 mph,
to the introduction this year of our new Hi-Velocity Kite to Fly
steady in winds of 15 MPH & Up, Pre-rigged kite line kits and a complete line of kite clips
and accessories. Tigress provides it.
Displayed below for your use and explanation a simple diagram of a typical kite set up.
One to three split shot on
outer edge of each kite need
For both
kite lines
Release
clip at
small swivel
75-100 ft
75 ft
Release
clip at
large swivel
75 ft
Kite Rod
Kite Rod
Wind
5 - 15 mph
15 - Foot
Sea Anchor
18 Gunnel, Pivoting
& Side Mount Rod Holders
ROD HOLDERS
OVAL HEAD GUNNEL ROD HOLDERS
MEDIUM AND LARGE OVAL GUNNEL ROD HOLDERS
Crafted of 316 Stainless
Head Size 3.28” x 4.06”
P
Part
Length
Angle
88525 9”
8
30° Head
88527 9”
0° Head
8
88529 9”
15° Head
8
88525-1
Backing Plate
8
88528 Blind Mount Swivel
8
9”
0° Head
ID
1 5/8
1 5/8
1 5/8
1 5/8
Head Size 3.85” x 4.88”
Constructed with cast bar as shown
8
88530
10 1/2”
30° Head
88532 10 1/2”
0° Head
88534 10 1/2”
15° Head
88530-1
Backing Plate
1 7/8
1 7/8
1 7/8
Designed to be used primarily with bent butt tackle.
PIVOTING ROD HOLDERS
Pivoting
Base
3 HOLE PIVOTING OVAL HEAD
Head Size 3.85” x 4.88”
Part
88520
88522
88524
88530-1
Length
Angle
10 1/2”
30° Head
10 1/2”
0° Head
10 1/2”
15° Head
Backing Plate
ID
1 7/8
1 7/8
1 7/8
4 HOLE EXTRA LONG PIVOTING RECTANGULAR HEAD
Head Size 4.25” x 4.75”
88520XL
88522XL
88524XL
88522SM
88524SM
88521
12 1/2”
30°Head
12 1/2”
0° Head
12 1/2”
15° Head
10 1/2”
0° Head
10 1/2”
15° Head
Backing Plate
1 7/8
1 7/8
1 7/8
1 7/8
1 7/8
SIDE MOUNT ROD HOLDERS
316 STAINLESS STEEL 9” PIVOTING SIDE MOUNT
Designed for applications where clamp-on or flush
mount holders are not practical. Can be mounted on
any vertical flat surface. White vinyl insert included to
protect your rod.
88542 9” x 1 5/8” ID Pivoting Side Mount Rod Holder
316 STAINLESS STEEL 9” SIDE MOUNT
Designed for applications where clamp-on or flush
mount holders are not practical. Can be mounted on
any vertical flat surface. White vinyl insert included to
protect your rod.
88540 9” x 1 5/8” ID Side Mount Rod Holder
Blind Mount, Round, Pivoting 19
& Oval Rod Holders
ROD HOLDERS MIRROR POLISHED 316 STAINLESS
ROUND HEAD CLOSED BASE
Heavy duty round head closed end base, with drain hole to accept 1/4” NPT pipe to hose fitting.
Head Size 3.85”
Part
77900
77901
77902
Length
9”
9”
9”
77906
77907
77908
10 1/2”
10 1/2”
10 1/2”
Angle
30° Head
15° Head
0° Head
ID
1 5/8
1 5/8
1 5/8
Large Rod Holder Head 4.13”
30° Head
15° Head
0° Head
1 7/8
1 7/8
1 7/8
BLIND MOUNT ROUND HEAD CLOSED BASE
US Patent # 8,291,636
Eliminate fastening from the top of flange and enhance
the look of your gunnel, with drain hole to accept 1/4”
NPT pipe to hose fitting.
Head Size 3.84”
Part
77900-1
77901-1
77902-1
Length
9”
9”
9”
Angle
30° Head
15° Head
0° Head
ID
1 5/8
1 5/8
1 5/8
BLIND MOUNT ROUND HEAD PIVOTING BASE
Patent Pending
Eliminate fastening from the top of flange and enhances
the look of your gunnel. Swivel base is designed to be
used primarily with bent butt tackle.
Head Size 3.84”
Part
77903
77904
77905
Length
9”
9”
9”
Angle
30° Head
15° Head
0° Head
ID
1 5/8
1 5/8
1 5/8
BLIND MOUNT OVAL HEAD CLOSED BASE
US Patent # 8,291,636
Eliminate fastening from the top of flange, Heavy duty
oval head closed end base, with drain hole to accept 1/4”
NPT pipe to hose fitting.
Head Size 3.28” x 4.06”
Part
88535-1
88537-1
88539-1
Length
9”
9”
9”
Angle
30° Head
0° Head
15° Head
ID
1 5/8
1 5/8
1 5/8
OVAL HEAD CLOSED BASE
Heavy duty oval head closed end base, with drain hole to
accept 1/4” NPT pipe to hose fitting
Head Size 3.28” x 4.06”
Part
88535
88537
88539
Length
9”
9”
9”
Angle
30° Head
0° Head
15° Head
ID
1 5/8
1 5/8
1 5/8
20 Economy Stainless Steel
Rod Holders
SEATIGER “ECONOMY” STAINLESS STEEL ROD HOLDERS
77170
77171
77172
77174
77177 & 77178
77179
Part
Angle
Description
Length x Rod Holder ID
77170
30°
Stamped Oval (Flip Top)
9” x 1 5/8” ID
77171
30°
Stamped Rectangular (Flip Top)
9” x 1 5/8” ID
77172
30°
Cast Oval (Flip Top)
9” x 1 5/8” ID
Stainless Rod Rigger
Tube 16.5” Holder 12” x 1 5/8” ID
Cast Rectangular (Open Top)
9” x 1 5/8” ID
77177
Removable Holder w/bracket
9” x 1 5/8” ID
77178
Replacement Mounting Bracket
H 4” x W 3.61”
77179
Side Mount
9” x 1 5/8” ID
77173
77174
30°
ROD RIGGER
Allows for your Rods to give you a
better fishing spread
Part 77173
HEAVY DUTY HI-POLISHED
STAINLESS WELD-ON
ROD HOLDER
Part 88155
• 316 Stainless Steel
• 10 1/2” Tapered
• Rod Holder ID 1 5/8”
21
CLAMP-ON ROD HOLDERS
316 STAINLESS STEEL ADJUSTABLE CLAMP-ON ROD HOLDERS
• Choose the angle you need while providing the versatility of
mounting either horizontally or vertically.
• High Polish Stainless Steel or Gold Titanium finish.
• Clamp-On Rod Holders are sized IPS Pipe.
• Includes a heavy white vinyl liner.
• Rod Holder ID 1 5/8”.
Part
Clamp Size
Finish
88190
3/4”
Silver
88190-1
3/4”
Gold
88191
1”
Silver
88192
1 1/4”
Silver
88192-1
1 1/4”
Gold
88193
1 1/2”
Silver
CLAMP-ON ROD HOLDER
3/4” - 1” ADJUSTABLE
CLAMP ON ROD HOLDER
Part 88176
• Improved version of the old
standard rail mount rod holder.
• 316 stainless steel clamp
mechanism with high polished
stainless tube
• White vinyl liner for rod protection. • Fits 3/4” and 1” rails.
• 9” x 2” OD.
• Rod Holder ID 1 5/8”.
HEAVY DUTY BEARING STYLE HINGES
(300 SERIES - HI-POLISHED)
Hinge Sizes 1-1/2” and 2” are standard with
no ball bearings.
Hinge Sizes 3”, 4”, 5” and 6” have unique ball
bearing pin assembly for easy opening and
closing.
Great for Cockpit Doors.
Stock Code
Description
21178
1-1/2 x 1-1/2
21180
2x2
21184
3x3
21188
4x4
21192
5x5
21196
6x6
22
Rod Holder Backing Plates
& Accessories
ROD HOLDER BACKING PLATES
77900-2
Round Head
Backing Plate
88525-1
Medium
Backing Plate
88530-1
Large
Backing Plate
88675
10’ Safety
Strap (Pair)
77910
316 Stainless
Pipe to Hose
Fitting 1/4”
IPS
88676
T-Top Rod
Safety Strap
(2 Each)
77911
Nylon Pipe to
Hose Fitting
1/4” IPS
88676-1
T-Top Rod
Safety Strap
(4 Each)
VINYL INSERTS
NEW
LINERSRH3
Liner is
UV Protected
PVC.
han 0°
If using other than
0°, cut to degree for proper use.
Part
88180-2
88530-2
88152-1
88176-2
88252-2
88152-2
77900-3
77901-3
77902-3
77900-4
77901-4
77902-4
Description
88180 Series
88520 & 88530 Series
Flared Weld-On
Adjustable Rod Holder Replacement Vinyl Insert
Rod Holder Replacement Vinyl Insert
OffShore Flared Weld-On
Black
Black
Black
White
White
White
Angle
Flared
Straight
Flared
Finish
9”
10 1/2”
10 1/2”
Flared
30°
0°
15°
30°
0°
15°
10 1/2”
9”
9”
9”
9”
9”
9”
Pipe Size Chart
Pipe
Size Number
Actual
Pipe
Diameter
Fractional
Pipe O.D.
(Approximate)
Pipe
Circumference
1
2
3
1.050
1.315
1.660
1-1/16”
1-5/16”
1-21/32”
3-5/16”
4-1/8”
5-7/32”
4
5
1.900
2.375
1-7/8”
2-3/8”
5-31/32”
7-15/32”
Rod Holder
& Chair Accessories
25
ROD HOLDER & CHAIR ACCESSORIES
LARGE ROD HOLDER EXTENDERS
Stainless & Nylon Rod Holder Extenders to shorten your rod holder to fit your bent butt fishing rod.
Available in 2”, 4” & 6”. We also offer our stainless steel swivel adapter to convert your standard rod
holder to a swivel rod holder. Fits Most Medium & Large Rod Holders. SS & Nylon 1.51” Wide
Part
88686
88686-1
Size
6”
4”
Material
Stainless Steel
Stainless Steel
88686-2
88688
88688-1
88688-2
2”
6”
4”
2”
Stainless Steel
Nylon
Nylon
Nylon
ROD HOLDER
SWIVEL ADAPTER
TIGERFISH BAT
Part 88687
Stainless Steel Swivel
Rod Holder Adapter
2.45” L x 1.50” W
Part 88682
18” All Aluminum Construction with Soft Eva
Foam Grip.
STAINLESS STEEL GIMBALS
88550
Maximum Strength and Built to Withstand the Rigors
of offshore Fishing! 316 Stainless Steel
88550 Flat Chair Gimbal (Four-Way Swivel For
mounting under base of chairs
Height: 3-1/8” Width: 4-1/8”
88552 Tubular Chair Gimbal
(Tubular mount fits 1” chair tubing.
Four way swivel)
105550 Fighting Chair Gimbal
EXTRA HEAVY DUTY CONSTRUCTION
FOR BIG ANTENNA’S AND TOUGH CONDITIONS
Part 66230
Heavy Duty Antenna Base with four way ratchet designed for deck and side mounting. Features heavy duty stainless steel construction and quick action handle for raising and lowering
your antenna. Suitable for all marine applications Hard Tops, T-Tops and Radar Arches. 9/32”
hole for cable feed and standard 1”-14 threads for attachment of antenna.
26 Rod & Reel Hangers
PREMIUM REEL HANGERS
• Gold anodized spring loaded
bracket holds reel in harness
lugs.
• Rod tip end rotates to lock in
the rod and store it up and out
of the way.
• Available for most Penn and
Shimano reels.
88700
88701
88702
88703
88704
88705
88706
88707
88708
88709
88710
88711
12T, 12LT, 16S Penn, 16LT, TTS 50
Shimano, 4/0-6/0 Finor (2.158)
20T Penn (1.468)
30T Penn, 30S (2.076)
30TW, 30SW, 30STW Penn, TLD 50
Shimano, VSW30 (2.823)
50T, 50S Penn (2.338)
50TW, 50SW, 50STW Penn, 80
Penn, 70S Penn, 9/0 Finor VSW50
(3.163)
4/0 Penn Senator, 7.5/0 Finor, TBM
30/50 Shimano (2.438)
80T, 80ST, 80TS Penn (3.323)
80TW, 80SW, 80STW Penn, Duel 9/0
(4.068)
130ST Penn, Ahab 50 Original Finor
(3.813)
30W Tiagra (2.970)
50 Tiagra (2.891)
88712
88713
88714
88715
88716
88717
88718
88719
88720
88721
88722
88723
88725
50WLRS Tiagra, 50W, 130H/S
Penn, TBM 80/130 Shimano (3.678)
80W Tiagra (4.387)
130 Tiagra (4.308)
TLD 25/30 II Shimano (2.213)
70 VS Penn (3.160)
TLD 20 Shimano (1.673)
20 Shimano (1.806)
30 Tiagra (2.345)
12 Tiagra (1.532)
16 Tiagra (2.262)
Penn Senator 6/0 (114H) (2.624)
Penn Senator 9/0 10/0 (3.250)
Adjustable Reel Hanger
(One Size Fits Most Reels)
PREMIUM ROD HANGERS
• To accommodate hanging your rods up and out
of the way with the rod butt and tip.
• Rod hangers available in anodized aluminum,
silver, gold, black and polished stainless steel.
• Dems: Closed End = 1.55” & Open End = .60”.
Part
88544
88545
88546
88547
Color
Silver Anodized
Gold
Black
316 Polished Stainless Steel
from Eastern Metal Supply
27
8-1/2” 15° Weld On Rod
Holder w/ 1-7/8” Oval
8-1/2” 15° Weld On Rod
Holder w/ 1-1/2” Oval
8-1/2” Straight Rod
Holder
8-1/2” Straight Rod
Holder with Welded Pin
Bracket with Welded Pin
WOOST85SL-CT
ver Straight with
1 x 1-1/2 oval
WOP802-SL
Silver
w/o Blade; w/Welded Pin
WOT8202-SL
W00802A-SL
Silver Angle Cut Bracket
Sil-
Silver
3/8” T-Top Wedge for 1” pipe
WOT8202-GL Gold
8-1/2” Swedged/Flared
Rod Holder
8-1/2” Swedged/Flared
Rod Holder
10” Rod Holders
10” Rod Holders
No Blade
3/8” Wedge for 1” Pipe
No Blade; with Welded Pin
WOP801-SL
Silver
WOP801-GL Gold
WOP801-M
Mill Finish
with Welded Pin
WOT8201-SL Silver
WOPE-SL
WOPE-GL
WOPE-MF
w/Welded Pin
Finish to be applied by fabricator
WOPE-SLB
Brushed Silver
10” Rod Holders
Offshore Series
2.125” ID
8-1/2” Spinning
Rod Holder
10” Swedged, no blade
WOPEB10-SL Silver
WOPEB10-MF Mill Finish
SRH-3 Silver Anodized
SRH-3-MF
Mill Finish
Without Bracket
WOL1001-SL
Silver
3/8” THICK Wedge
Silver
Gold
Mill Finish
WOPE1001ET-SL Silver
WOPE1001ET-MF Mill Finish
WOPE1001ET-GL Gold
TWST10-SL
Silver
10” Straight w/ 3/8” t-top blade;
notched for 1” pipe
Rod Holder Liners
LINER7 for 8-1/2" straight rod holders
T88152-1 for 8-1/2" & 10"
swedged/flared rod holders
T88152-2
for 10" swedged/flared Offshore Series
LINERSRH3
Fitted liner for spinning rod holder
LINER7, T88152-1, LINERSRH3
28 Triple, Bolt-On
& Transom Rod Holders
OFFSET TRIPLE ROD HOLDER
W/STORAGE CUPS
88149 Straight Butt
w/cup holders
• This quality rod holder
can be used for rod
storage and is most
useful in kite fishing.
• Cups allow for holding
your rigging tools as
well as your drink.
• Constructed of
anodized aluminum
and White Liner to
protect your Rods.
• Tube ID 1 7/8” Base
OD 1.49”.
OFFSET TRIPLE ROD HOLDER
• Triple offset can be
used port or starboard
• Additional rod storage
or for kite fishing.
• Constructed of
anodized aluminum.
• Tube ID 1 7/8” Base
OD 1.49”.
88149-1 Straight butt
SINGLE BOLT-ON ROD HOLDER
• This Versatile Rod Holder can be
mounted on your gunnel,
transom or just about anywhere
you need additional rod storage.
• Constructed of anodized
aluminum
• Includes white liner
TRIPLE BOLT-ON ARRAY
• Designed to increase
your rod storage.
• Constructed of cold
drawn aluminum with
brushed finish.
• Includes white liner.
Part 88145
Part 88146
NEW
Designed for spinning Rods & Reels
• The tube is polished to a mirror finish & anodized clear.
• 8 1/2 Long 7/8 opening; Slot 2 1/2 Long
• Liner: LINERSRH3
SRH-3
TRANSOM MOUNT ROD HOLDERS
• Constructed of cold drawn anodized aluminum
• Includes White liners to protect your rod.
• Available with either 4 rod holders or 5 rod
holders as shown.
Part
Description
Length
88144
Five Rod Holder Transom Mount
35”
88144-1
Four Rod Holder Transom Mount
28”
Aluminum Marine Hardware
29
Hard Top Bushings and Washers - Powder Coated Marine White
Stock Code
HTP-1
HTP-2 (Special Order)
HTW-1
HTW-2 (Special Order)
Description
1-5/8 x 1-1/2 x 1 Hard Top Bushing
1-3/4 x 1-1/8 x 3/4 Hard Top Bushing
1-1/8 x 1/4 Hard Top Washer
1-5/8 x 1/4 Hard Top Washer
Hard Top Bushings
and Washers
Rod Butt
Stock Code
RODG1
Description
Rod Butt for 1” pipe Polished
Rod Butt
Cup Holders
Stock Code
PCHE-BP
PCHE-SS
PCHE
Description
Black Plastic Cup Insert (w/ Stainless Ring on top)
Mates with PCHE
Stainless Steel Cup Insert
Mates with PCHE
Cup Holder Mounting Ring (Polished and Anodized)
(Accepts PCHE-BP and PCHE-SS)
Black Plastic Cup Insert; Stainless Cup Insert Bottom: PCHE Mounting Ring
Folding/Pivoting Back Rest
Stock Code
FBRA-KIT
FBRA-KIT-BLK
Description
PBRP-404
4" 4 Hole Round Pad; WHITE
PBRP-404-BK
(w/ 3/8” counter sunk center hole white plastic)
4" 4 Hole Round Pad; BLACK
(w/ 3/8” counter sunk center hole black plastic)
50045
3/8" x 1" notched thread screw
Folding/Pivoting Back Rest Assembly
Folding/Pivoting Back Rest Assembly (Black)
left-right: Folding/Pivoting Back Rest Assembly;
FBRA-KIT; FBRA-KIT-BLK
left to right: PBRP-404; 50045
FBRA-SLEEVE
Folding Back Rest Sleeve for 1”
FBRA-SLEEVE
(shown with 1” pipe inserted)
Custom size pads built to your specifications
(minimum quantity required)
30
Breakaway Pins
Stock Code
BAP-750
BAP-1000
BAP-1250
BAP-1500
BAP-2000
Size In Inches
3/4
1
1-1/4
1-1/2
2
Breakaway Pins
Pivoting Breakaway Pin
Stock Code
PIVPIN-750
Size In Inches
Pivoting breakaway pin for ¾” pipe
Threaded Antenna Boss
Stock Code
TAB-1
Size In Inches
3.5 (1”-14 Thread / .500 Through Hole Size)
Pivoting Breakaway Pin
Threaded Antenna Mount
Stock Code
TAM-1
Size In Inches
4” (¾” I.D. and 1” of threads)
Threaded Antenna Boss
End Caps
Stock Code
APC-750
APC-100
APC-125
APC-150
APC-200
Size In Inches
3/4
1
1-1/4
1-1/2
2
Threaded Antenna Mount
End Caps
Plug Boss
52-63-44068
3/4” Plug Boss for ¾ sch 40 pipe
1/4 -20 threaded center hole; for attachment of grab rails
Hand Rail Boss - Bright Dip Anodized
Stock Code
HRB-1
Size In Inches
1 x 1-7/8
3/4” Plug Boss; Inserted into pipe
Brushed Mounting Angles (2 x 2 x 1/4)
Stock Code
Size In Inches
Fastener
MA-151
2 (1 hole)
1/4
MA-402
4 (2 hole)
1/4
MA-603
6 (3 hole)
1/4
MA-804
8 (4 hole)
1/4
25-BD-300
2 x 2 x 1/4 Arch Angle x 20’
6 pcs/box
Used to fabricate Brushed Mounting Angle
Hand Rail Boss
Polished Mounting Angles (2 x 2 x 1/4)
Stock Code
PMA-151
PMA-402
PMA-603
PMA-804
Size In Inches
2 (1 hole)
4 (2 hole)
6 (3 hole)
8 (4 hole)
Fastener
1/4
1/4
1/4
1/4
Mounting Angles
Sleeves - Outside
BDA Polished
Stock Code
SLV-1-6
SLV-1.250-6
SLV-1.25-8.5
SLV-1.50-6
SLV-1.50-8.5
SLV-1.50-10 (TX)
SLV-2-6
SLV-2-8
SLV-2-10
SLV-2-12
Mill Finish
Description
1x6
1-1/4 x 6
1-1/4 x 8-1/2
1-1/2 x 6
1-1/2 x 8-1/2
1-1/2 x 10
2x6
2x8
2 x 10
2 x 12
Stock Code
SLV-1.50-6MF
SLV-1.50-10MF
SLV-2-8MF
SLV-2-10MF
SLV-2-12MF
Pipe Aligners
Stock Code
PA-0752
PA-1002
PA-1253
PA-1505
PA-2005
31
Description
1-1/2 x 6
1-1/2 x 10
2x8
2 x 10
2 x 12
Sleeves - Outside
Antenna Ratchet Mounting Pads
Description
3/4
1
1-1/4
1-1/2
2
Stock Code
AP-320
AP-4
Pipe Aligners
Description
3 x 2 x 1/4
4 x 4x 1/4
Antenna Ratchet Mounting Pads
Bow Rail Components
Stock Code
BREC
BRSS
GREC
GRMS
Description
Fastener
Bow Rail End Cap for ¾” Pipe; 2.25” High
1/4
Bow Rail Mid Span Support for ¾” Pipe; 2.25” High
1/4
Grip Rail End Cap for ¾” pipe; 2.625” High
1/4
Grip Rail Mid Span Support for ¾” pipe; 2.625” High
1/4
Left: Bow Rail
End Cap
Right: Bow Rail
Mid Span
Support
Marine Hardware & Accessories
Complete line of components for building ski and wakeboard towers. Components are made
from Bright Dip Anodized 6061-T6 aluminum and are compatible with 1-1/2" sch 40 pipe.
Locking Break-Away
Pin
ST-LBAP
Aft Attachment Pad
ST-AAP
Forward Attachment
Pad
ST-FAP
Male/Female
Swing Pin
ST-MFSP
Ski Ball Assembly
w/ Nylon Insert
ST-SBA
Fits 2” Pipe
ST-SBA-MF Mill Finish
Fits 1-1/4" Pipe
ST-SBA-BDA
Fits 1-1/4"
Pipe
BDA
32
Folding Foot Rest Hardware
Stock Code
FR-ANGLE
Description
Flat Surface Mount (Sold in Sets, Left and Right)
Each side includes: 1) 2 x 2 x 3 Hinge Block; 1) 5/16 Bolt; 2) Delrin Washers; 1) 1" Female Pin
BOFR
Bolt On Foot Rest Hardware
Sold in sets (1 Right & 1 Left) Includes (2) 1” Male Pins (1) 5/16” Bolt
FRP-WELD-ON
Weld On Blade Mount (polished blade) (drops past horizontal)
FR-Angle
BOFR
includes:1) 2 x 3 Hinge Block; 1) 5/16 Bolt; 2) Delrin Washers; 1) 1" Female Pin
Weld On Blade Mount (brushed blade) (drops past horizontal)
includes:1) 2 x 3 Hinge Block; 1) 5/16 Bolt; 2) Delrin Washers; 1) 1" Female Pin
FR-WELD-ON
FR-WELD-ON-90
Weld On Blade Mount (brushed blade) (drops to horizontal)
includes:1) 2 x 2-1/2 Hinge Block; 1) 5/16 Bolt; 2) Delrin Washers; 1) 1" Female Pin
Ear Mounts
Stock Code
EM-750
EM-100
EM-200
Description
3/4” Ear Mount with 1/4” Hole
1” Ear Mount with 5/16” Hole
1-1/4 or 1-1/2” Ear Mount with 3/8” Hole
left: FR-Weld-On; right: FR-Weld-On-90
Folding Bench Seat Hardware
Stock Code
FBSH-T
Ear Mounts
Description
Folding Bench Seat Hardware
includes:1) 1/4 x 2 x 2 T-Stock Hinge; 1) 1/4" Socket Cap Screw;
2) Delrin Washers; 1) 3/4" Female Pin; 1) Retaining Clip;
1) Retaining Clip Mount & Screw
FBSH-Angle
Mounting Angle
Sold in pairs with 1” female pin, right & left
for surface mounting Seat to Transom, etc.
FBSH-Angle
FBSH-T
Hinge Bracket
Stock Code
HB-250
HB-375
HB-500
HB3L
Blade Thickness In Inches
1/4
3/8
1/2
3 Leg Bracket: 1/4” Oustide Legs & 3/8” Inside Leg
Alignment Pins
Stock Code
ALP-100
ALP-125
ALP-150
ALP-200
Hinge Bracket
3 Leg Bracket
Size In Inches
1" Alignment Pin
1-1/4" Alignment Pins
1-1/2" Alignment Pin
2" Alignment Pin
Slot Size
1/2" Through Hole Size
1" Through Hole Size
Alignment Pins
33
Female Pins
Stock Code
FP-75375
FP-100375
FP-100500
FP-125500
FP-125500WS
FP-150500
FP-150500WS
FP-200750
Size In Inches
3/4
1
1
1-1/4
1-1/4
1-1/2
1-1/2
2
Slot Size
3/8
3/8
1/2
1/2
5/8
1/2
.630
3/4
Fastener
1/4* (Wide Slot)
5/16
5/16* (Wide Slot)
3/8
3/8* (Wide Slot)
3/8
3/8* (Wide Slot)
1/2* (Wide Slot)
Female Pins
Female Oval Pin
FOP-100500
1
1/2
5/16
Mates with 1 x 1-1/2” Oval Tube (52-63-6354, 25-BD-200, 25-BR-200)
Bolts included with all Female Pins
*These Pins are supplied with Washers
Male Pins
Stock Code
MP-750
MP-1000
MP-1250
MP-1500
MP-2000
Size In Inches
3/4
1
1-1/4
1-1/2
2
Female Oval Pin
Female & Male Pin shown connected; Not
sold together; sold individually
Fastener
1/4
5/16
3/8
3/8
1/2
Male Pins
Quick Release Pin
QRP-1
1” Quick Release Pin; for 2 locking positions 0o and 90o
Quick Releae Pin
Half Pins
Stock Code
HP-750
HP-1000
HP-1250
HP-1500
Size In Inches
3/4
1
1-1/4
1-1/2
Fastener
3/8
3/8
3/8
3/8
Size In Inches
3/4 x 1
1-5/16 x 1
1-5/16 x 1-1/2
1-5/8 x 2
1-7/8 x 2
Fastener
1/4”-20 (one end)
3/8”-16 (one end)
3/8”-16 (one end)
3/8”-16 (one end)
3/8”-16 (one end)
Tower Boss
Stock Code
TB-750
TB-1312-10
TB-1312-15
TB-1625-20
TB-1875-20
Half Pins
Tower Boss
Threaded Knob
Stock Code
Description
BK-KNOB (NC/TX)
Black Threaded Knob 3/8”-16 (one end)
For Tower Boss, Femal Pin Connections
Threaded Knob
34
Fiberglass Boxes & Hard Tops
Fiberglass Electronics Box
EMSSEB
Small, Black Face
24” W x 15” D x 10” H
EMSLEB
Large, Black Face
30” W x 17” D x 11” H
½” Door & Frame, 1 Gas Shock, Stainless Lock
½” Door & Frame, 1 Gas Shock, Stainless Lock
EB32W (NC)
Large, Black Face
32" W x 20" D x 10" H
Crowned top - White Exterior
All marine grade hardware and gel coat (inside and out).
Gel coat has excellent gloss and fade resistance. Gasket
on door for a water resistant box.
Also Available as Special Orders:
Size: 24” W and 28” W
All sizes can be made with White or Off White Exteriors
Upper Tower Control Box
TWRBOX 28” W x 11-1/2” H x 20” D
GemLux Latch & Friction Hinges/Cored
Upper Control Station
UCS
White Fiberglass
25-1/2” W x 15-1/2” D x 13” H
Radius Back Fiberglass Electronics Box
24EBOX-R
24” W x 15” D x 12” H
White Fiberglass
GemLux Latch and Friction Hinges, cored
Fiberglass Poling Platform Cap
PPFC
Fiberglass Cap (White)
24" W x 42" L x 1-1/2" W Lip
White Fiberglass Hard Top
WFHT
66” x 88” x 1-3/8”
• White gelcoat yacht finish
• Non-skid topside
• Honeycomb core
• Front/rear molded in spreader
pods
• Internal wire-ways
Leaning Post Tray
7000TRAY
White Fiberglass
33” W x 9” D x 6-3/4” H
4RHTMP
Hard Top Mounting Pads
Bright Dipped - POLISHED
4RHTMP
4 x .375 (3/8” thread)
Sold in set of 2 pads; Hardware NOT included.
4 x 12.875 x .375 8 Holes
HTMP
HTMP
35
Aluminum Marine Pads
Round Marine Pads - (Packaged in pairs)
POLISHED PADS
____
D = Polished
B = Brushed
3-Hole Round Pads - Bright Dipped POLISHED - Standard Edge
Stock Code
D-253
52-63-6781
D-303
D-303A
D-303-NCS
D-300-CH
D-353
D-353-NCS
D-403
D-403-250
D-403-375
D-400-CH
D-401 (NC)
D-453
D-453-NCS
D-503
D-500-CH
D-501 (NC)
Size in Inches
2.5
2.5
3
3
3
3
3.5
3.5
4
4
4
4
4
4.5
4.5
5
5
5
Fastener
#10
#10 (5/16 threaded center hole)
#10
1/4
1/4 (NO countersink on holes)
1/4 (1/4 center hole ONLY)
1/4
1/4
1/4 (1-1/4 center hole)
1/4 (3/8 center hole - NOT threaded)
1/4
1/4
4” 3-Hole Round Pad
Bright Dipped Polished (D)
D-400-CH & D-500-CH
Center Hole Only
3 Hole Round Pads - Bright Dipped POLISHED - “EP” STYLE
Stock Code
EP-253
EP-303
EP-353
EP-403
EP-453
Size in Inches
2.5
3
3.5
4
4.5
Fastener
3/16
1/4
1/4
1/4
1/4
4-Hole Round Pads - Bright Dipped POLISHED - Standard Edge
Stock Code
D-304
D-354
D-404
D-404-NCS
D-404-250
D-404OS
D-454
D-504
D-504-250
Size in Inches
3
3.5
4
4
4
4
4.5
5
5
Fastener
#10
1/4
1/4
1/4 (offset)
1/4
1/4
4-Hole Round
Pad - Bright
Dipped
Polished (D)
1-1/4” center
hole
4 Hole Round Pads
- Offset Bright
Dipped Polished (D)
4 Hole Round Pads - Bright Dipped POLISHED - “EP” STYLE
Stock Code
EP-354
EP-404
EP-404-150
EP-404OS
EP-454
EP-454-150
EP-504
Size in Inches
3.5
4
4
4
4.5
4.5
5
Fastener
1/4
1/4
1/4 (1-1/2” center hole)
1/4 (offset)
1/4
1/4 (1-1/2” center hole)
1/4
Custom size pads built to your specs (minimum quantity required)
4 Hole Round Pads (EP Style)
Bright Dipped Polished
36
HIGH POLISHED PADS
D = Polished
B = Brushed
3-Hole Round Pads - HIGH POLISHED - “EP” STYLE
Stock Code
PEP-253
PEP-303
PEP-353
PEP-403
PEP-503
Size in Inches
2.5
3
3.5
4
5
Fastener
#10
1/4
1/4
1/4
1/4
4-Hole Round Pads - HIGH POLISHED - “EP” STYLE
Stock Code
PEP-404
PEP-404OS
PEP-454
EP-455
PEP-504
Size in Inches
4
4
4.5
4.5
5
Fastener
#10
1/4 Offset
1/4
5/16 (5 holes)
1/4
BRUSHED PADS
3-Hole Round Pads - Bright Dipped BRUSHED - Standard Edge
Stock Code
B-303A
B-353
B-400-TCH
B-403
B-453
B-503
Size in Inches
3
3.5
4
4
4.5
5
Fastener
1/4
1/4
3/8 (Threaded Center Hole)
1/4
1/4
1/4
4-Hole Round Pads - Bright Dipped BRUSHED - Standard Edge
Stock Code
B-404
B-404OS
B-454
B-504
Size in Inches
4
4
4.5
5
Fastener
1/4
1/4 (offset)
1/4
1/4
4” 4-Hole Round
Pad Bright Dipped
Brushed (B)
4 Hole Round Pads - Bright Dipped BRUSHED - “EP” STYLE
Stock Code
EPB-404OS
Size in Inches
4
Fastener
1/4 (offset)
MILL FINISH PADS
3-Hole Round Pads - MILL FINISH - Standard Edge
Stock Code
Size in Inches Fastener
52-63-6781-MF 2.5
#10 (5/16 Threaded Center Hole; Mill Finish)
(mates with D-403-375 for folding/pivoting backrest supports)
D-303-MF*
3
1/4 (Mill Finish)
D-353-MF*
3.5
1/4 (Mill Finish)
D-353-NCS-MF 3.5
1/4 (Mill Finish - no counter sink)
D-403-MF
4
1/4 (Mill Finish)
D-403-NCS-MF 4
D-403150-NCS-MF 4
1/4 (Mill Finish - no counter sink; 1-1/2” center hole)
D-453-MF
4.5
1/4 (Mill Finish)
D-453-NCS-MF 4.5
D-503-MF
5
1/4 (Mill Finish)
4-Hole Round Pads - MILL FINISH - Standard Edge
Stock Code
D-304-MF
D-354-MF
D-404-MF
D-454-MF
D-504-MF
D-504-250
Size in Inches
3
3.5
4
4.5
5
5
Fastener
#10 (Mill Finish)
1/4 (Mill Finish)
1/4 (Mill Finish)
1/4 (Mill Finish)
1/4 (Mill Finish)
3 Hole Round Disc - MILL FINISH - “EP” STYLE
Stock Code
EP-303-MF
EP-353-MF
EP-403-MF
Size in Inches
3
3.5
4
Fastener
1/4 (Mill FInish)
1/4 (Mill FInish)
1/4 (Mill FInish)
4 Hole Round Disc - MILL FINISH - “EP” STYLE
Stock Code
EP-404-MF
Size in Inches
4
Fastener
1/4 (Mill FInish)
37
D = Polished
B = Brushed
38
Rectangular Marine Pads - (Packaged in pairs)
POLSHED PADS
2-Hole Rectangular (Oblong/Shape) Pads - Bright Dipped POLISHED
Stock Code
RP-1535-2
RP-2040-2
Size in Inches
1-1/2 x 3-1/2
2x4
Fastener
1/4
1/4
4-Hole Rectangular (Oblong/Shape) Pads - Bright Dipped POLISHED
RP-1535-4
RP-2040-4
RP-2540-4
RP-3040-4
RP-3040-4-MF
RP-3040-41250
RP-3045-4
RP-3550-4
RP-4060-4
RP-4060-41OB
RP-4060-4OB
1-1/2 x 3-1/2
2x4
2-1/2 x 4
3x4
3x4
3x4
3 x 4-1/2
3-1/2 x 5
4 x 6 x 3/8
4 x 6 x 1/4
4 x 6 x 3/8
#10
1/4
1/4
1/4
1/4 (Mill Finish)
1/4
1/4
1/4
1/4
5/16
4-Hole Rectangular (Radius Corner) Pads - Bright Dipped POLISHED
RP-2040-4RC
RP-3040-4RC
2x4
3x4
RP-3040-4RC-MF 3 x 4
2 Hole Rect. Pads
Oblong/Shape
4 Hole Rect. Oblong/Shape Pads
Polished
1/4
1/4
1/4 (Mill Finish)
HIGH POLISHED PADS
Rectangular (Oblong/Shape) Pads - HIGH POLISHED - “EP” STYLE
Stock Code
PEP-3040-4RC
PEP-3045-4OB
PEP-3045-4OB5
RC-4060-4OB
RP-4060-425
RP-4060-4375
RC-4565-4OB
RC-4565-4OBN
RC-4565-4OB3
RC-4565-4OB2
RP-5070-4OB
RP-5070-6OB
Size in Inches
3 x 4 x .250
3 x 4.375 x .250
3 x 4.375 x .250
4 x 6 x .375
4 x 6 x .250
4 x 6 x .375
4.5 x 6.5 x .250
4.5 x 6.5 x .250
4.5 x 6.5 x .375
4.5 x 6.5 x .375
5 x 7 x .375
5 x 7 x .375
Fastener
4 Holes (1/4”): Radius Corner; NOT Oblong
4 Holes (1/4”): Oblong
4 Holes (1/4”): Oblong; 1-1/2” Center Hole
4 Holes (5/16”): Countersunk; 2” Center Hole (6463-T66)
4 Holes (5/16”): NO Countersink; (2-3/8” Center Hole (6463-T66)
4 Holes (5/16”): NO Countersink (6463-T66)
4 Holes (1/4”): NO Countersink; 3” Center Hole (6463-T66)
4 Holes (1/4”): Countersunk; 2-3/8” Center Hole (6463-T66)
4 Holes (1/4”): Oblong
4 Holes (1/4”): Oblong with 6 Outside Holes
4 Hole Rect.
Oblong/Shape Pads
Polished (1-1/4 center hole)
BRUSHED PADS
2-Hole Rectangular (Radius Corner) Pads - Bright Dipped BRUSHED
RB-2040-2
2x4
4 Hole Rect.
Radius Corner Pads
1/4
4-Hole Rectangular (Oblong/Shape) Pads - Bright Dipped BRUSHED
RB-2540-4
RB-3040-4OB
RB-3045-4-MF
RB-3045-4
RB-3550-4
RB-4060-4
RB-4060-41OB
RB-4060-4OB
2-1/2 x 4
3x4
3 x 4-1/2
3 x 4-1/2
3-1/2 x 5
4 x 6 x 3/8
4 x 6 x 1/4
4 x 6 x 3/8
1/4
1/4
1/4 (Brushed/No Anodize)
1/4
1/4
1/4
1/4
5/16
4-Hole Rectangular (Radius Corner) Pads - Bright Dipped BRUSHED
RB-2040-4
RB-2540-4R
RB-3040-4
2x4
2-1/2 x 4
3x4
1/4
1/4
1/4
4 Hole Rect.
Radius Corner Pads Brushed
39
Miscellaneous Marine Pads - (Packaged in pairs)
D = Polished
B = Brushed
2-Hole Oval Pads
Stock Code
OP-2035-2
OP-2035-2P
OP-2035-2P-MF
OP-2540-2B
OP-2540-2P
Size in Inches
2 x 3.5 (brushed)
2 x 3.5 (polished) 1/4
2 x 3.5 (mill finish)
2.5 x 4 (brushed)
2.5 x 4 (polished) 1/4
Fastener
1/4
1/4
1/4
Oval Pads
Tear Drop Pads - Bright Dipped - Polished
Stock Code
TD-3040
Size in Inches
Fastener
2 x 3 (with countersunk hole)
Tear Drop Pads
Triangular Heart Pads
Stock Code
TP-353
HP-3040-3
HB-3040-3
Size in Inches
3-1/2
3 x 4 (Polished)
3 x 4 (Brushed)
Fastener
1/4
1/4
1/4
Triangular Heart
Pads
Heart Pad
Diamond Pads
Stock Code
DP-2035-3
DB-2035-3
DB-2045-3
Size in Inches
2 x 3-1/2 (Polished)
2 x 3-1/2 (Brushed)
2 x 4-1/4 (Brushed)
Fastener
1/4
1/4
1/4
Size in Inches
2 x 1/4
Fastener
3/16
Diamond Pads
Square Pad
Stock Code
SB-222
Square Pad
Outrigger Hard Top Pad
Stock Code
LHOP-8.75 (NC)
Description
Outrigger Hard Top Pad
Outrigger
Hard Top Pad
Pad for Windshield Guard
Stock Code
EPWP-150 (NC)
Description
1-1/2" Round Pad (for 3/4” Pipe; 3/8" threaded center hole)
Windshield
Pad
40
Special Marine Pads
Round Pads - Bright Dipped POLISHED - Standard Edge
Stock Code
Size (Inches)
D-300-CH
11386-12
D-400-CH
D-500-CH
3 x .250
3 x .375
4 x .250
5 x .250
Description
Contains center hole only; countersunk
Contains center hole only (threaded 3/8-16); countersunk
* Special Order
Fastener
¼
¼
¼
¼
Round Pads - Bright Dipped BRUSHED - Standard Edge
Stock Code
Size (Inches)
EB-250-CH
EB-300-CH
B-400-TCH
57678-14A
57678-13A
57678-11A *
2.5 x .250
3 x .250
4 x .375
4.5 x .375
6 x .250
6 x .375
Description
Contains NON-Threaded Center Hole Only (3/16”): NO Countersink (6463-T66)
3 Holes (5/16”): Countersunk (6061-T6)
3 Holes (5/16”): NO Countersink; NO Center Hole (6061-T6)
3 Holes (5/16”): Countersunk; 2” Center hole (6061-T6)
57678-11A
Round Pads - MILL FINISH - Standard Edge
Stock Code
Size (Inches)
57678-15M
57678-12M
4.5 x .250
6 x .250
Description
3 Holes (5/16”): NO Countersink; 2” Center Hole (6061-T6) - Backing Plate
57678-7A
Rectangular (Oblong/Shape) Pads - Bright Dipped BRUSHED
Stock Code
Size (Inches)
57678-4A
57678-5A
57678-6A *
57678-7A
57678-2AA
57678-8A
4 x 6 x .375
4 x 6 x .375
4 x 6 x .375
4 x 6 x .375
4 x 12 x .375
4.5 x 6 x .375
Description
4 Holes (5/16”): NO Countersink; 2” Center Hole (6463-T66)
4 Holes (5/16”): Countersunk; 2” Center Hole (6463-T66)
57678-2AA
Rectangular (Oblong/Shape) Pads - 6463-T66 - MILL FINISH
Stock Code
Size (Inches)
57678-9M
57678-4M *
57678-1M
57678-10
4 x 6 x .250
4 x 6 x .375
4 x 12 x .375
4.5 x 6 x .250
57678-8A
Description
4 Holes (5/16”) and 2” Center Hole: NO Countersink
4 Holes (5/16”): NO Countersink
6 Holes (5/16”): NO Countersink and 2 - 2” Center Holes
4 Holes (5/16”): NO Countersink; 2 - 2” Center Holes
Poling Platform Mounting Pad - Bright Dipped - POLISHED
Stock Code
Size (Inches)
Description
PPMP
3 x 10 x .25
5 Holes
57678-4M
57678-1M
Polling Platform
Mounting Pad
4” Round Hard Top Mounting Pad - Bright Dipped - POLISHED
Stock Code
Size (Inches)
4RHTMP
4 x .375
Description
(3/8” thread) Sold in set of 2 pads; Hardware NOT included.
Hard Top Mounting Pad - Bright Dipped - POLISHED
Stock Code
Size (Inches)
Description
HTMP
4 x 12.875 x .375
8 Holes
4” Round Hard Top
Mounting Pad
(2 pads)
Hard Top
Mounting Pad
Leaning Post Pad - Bright Dipped - POLISHED
Stock Code
Size (Inches)
Description
LPP-21625
2 x 16
6 Holes
Leaning
Post Pad
Inline & Hand Rail
LED Lighting
41
T-TOP & TOWER IN-LINE LED LIGHTS
PATENT #US 8,303,145 B2
IN-LINE ALUMINUM LED LIGHTS
Make your T-top or Tuna Tower look as though it came with lighting.
• Available for the non-structural part of your 1-5/16” Aluminum Schedule 40 Pipe.
• Includes the necessary couplers for installation.
• May be installed overhead, on T-top side rail and in many other locations where you may enjoy extra lighting.
• Simply cut 12 or 20” out of your non-structural schedule 40 aluminum pipe and place in.
• 12” and 20” Inlines offers low power consumption, low glare and long life, 12V DC Power only.
• High efficiency strips are waterproof (not to be submerged).
Part
Length
Clamp
Size
Color
Part
Length
Clamp
Size
Color
88985
20”
1-5/16”
Day Light White
88985-10
20”
1-5/16”
Multicolor no remote
88985-1
20”
1-5/16”
Night Vision Red
88985-11
20”
1-5/16”
Multicolor w/White controller
88985-2
20”
1-5/16”
Dual Red/White
88985-4
12”
1-5/16”
Day Light White
88985-3
20”
1-5/16”
Blue
88985-5
12”
1-5/16”
Night Vision Red
88985-7
20”
1-5/16”
Dual Blue/White
88985-6
12”
1-5/16”
Blue
88985-9
20”
1-5/16”
Multicolor W/Black controller
88985-8
12”
1-5/16”
Dual Blue/White
HAND RAIL LED LIGHTS
LIGHT UP YOUR
HAND RAIL !!!
PATENT # US 8,303,145 B2
• Illuminate your passage ways with our new LED hand Rails.
• Place them on any flat surface where lighting is needed to move safely around your boat.
Part #
Length
Color
Part #
Length
Color
88997
20”
Day Light White
88997-10
20”
Multicolor no remote
88997-1
20”
Night Vision Red
88997-11
20”
Multicolor w/White controller
88997-2
20”
Dual Red/White
88997-4
20”
Day Light White
88997-3
20”
Blue
88997-5
20”
Night Vision Red
88997-7
20”
Dual Blue/White
88997-6
20”
Blue
88997-8
20”
Multicolor W/Black controller
88997-9
20”
Dual Blue/White
42
CLAMP-ON LED LIGHTS
• Enhance your T-top or Tuna Tower with our bright finished aluminum clamp-on lights.
• Fits non-structural 1-1/16” & 1-5/16” Aluminum Schedule 40 Pipe.
• May be installed overhead, on t-top, side rail and in many other locations that you
have 3/4” - 1” IPS Pipe.
• 12” and 20” Inlines offers low power consumption, low glare and long life, 12V DC
Power only.
• High efficiency strips are waterproof (not to be submerged).
Each package includes bushing to reduce from 1-5/16” to 1-1/16”
Part
Length
Clamp Size
Color
88990
12”
1-1/16” & 1-5/16”
Day Light White
88991
12”
1-1/16” & 1-5/16”
Night Vision Red
88991-2
12”
1-1/16” & 1-5/16”
Blue
88991-3
12”
1-1/16” & 1-5/16”
Dual Blue/White
88980
20”
1-1/16” & 1-5/16”
Day Light White
88981
20”
1-1/16” & 1-5/16”
Night Vision Red
88982
20”
1-1/16” & 1-5/16”
Dual Red/White
88982-1
20”
1-1/16” & 1-5/16”
Blue
88982-2
20”
1-1/16” & 1-5/16”
Dual Blue/White
88982-3
20”
1-1/16” & 1-5/16”
Multicolor w/Black controller & Remote
88982-4
20”
1-1/16” & 1-5/16”
Multicolor No controller
88982-5
20”
1-1/16” & 1-5/16”
Multicolor No controller
LED Strip Lighting
43
LED LIGHT STRIPS
MULTICOLOR LED STRIP
NEW
20” Multi-Color Strip
25’ Wire
Black Controller
LED LIGHT STRIPS
Use to replace your existing LED light
• Placed under your gunnel, engine room,
anywhere you can imagine
• Will give your boat The Pizzazz and Color Your
Looking for.
• 12” strip’s Draw white/1.4A
red/ 2.8A @ 12V DC Power.
• 20” strips Draw blue/white/2.4A
red/red-white/4.8A @ 12V DC Power.
• High efficiency LED’s offer low power
consumption, low glare, long life
• High efficiency strips are waterproof
(not to be submerged).
White Controller
• 20” LED strip that allows you to change color and
frequency with the press of a switch.
• LED strip from Tigress include a controller to
operate the function.
• Program your light to display one color or 15
differant shades.
• Colors include white, red, blue, green, pink, fuchsia,
yellow, purple and varying shades of each color.
• Also available in all of our light housings as shown
on all four pages.
Part
20”
Multicolor
Strip
88996-5
X
88996-6
X
Black
Controller
White
Controller
X
88996-7
X
88996-8
X
88996-9
X
X
X
88996-10
88996-11
25’
Extra Part
Wire
w/8 wire
connectors
X
X
88996-12
X
X
88996-13
X
88996-14
X
X
X
X
X
HIGH EFFICIENCY LED LIGHTS STRIPS
Part
88995
88995-1
88995-2
Size
12”
12”
12”
Color
Day Light White
Night Vision Red
Blue
88995-3
88996
88996-1
88996-2
88996-3
88996-4
12”
20”
20”
20”
20”
20”
DualBlue/White
Bright White
Night Vision Red
Blue
Dual Red/White
DualBlue/White
Mount, Center Mount
44 Bracket
& Weld Mount LED Lighting
BRACKET, CENTER AND WELD-ON
Bracket Mount
Center Bracket Mount
BRACKET MOUNT
CENTER MOUNT
WELD MOUNT
Part
Size
Color
Part
Size
Color
Part
Size
Color
88977
20”
Day Light White
88979
20”
Day Light White
88993
20”
Day Light White
88977-1
20”
Night Vision Red
88979-1
20”
Night Vision Red
88993-1
20”
Night Vision Red
88977-2
20”
Dual Red/White
88979-2
20”
Dual Red/White
88993-2
20”
Dual Red/White
88977-3
20”
Blue
88979-3
20”
Blue
88993-3
20”
Blue
88977-4
20”
Dual Blue/White
88979-4
20”
Dual Blue/White
88993-4
20”
Dual Blue/White
20”
Multicolor (Black)
88977-5
20”
Multicolor (Black)
88979-5
20”
Multicolor (Black)
88993-5
88977-6
20”
Multicolor(White)
88979-6
20”
Multicolor(White)
88993-6
20”
Multicolor(White)
88977-7
20”
Multicolor
(No Remote)
88979-7
20”
Multicolor
(No Remote)
88993-7
20”
Multicolor
(No Remote)
88978
12”
Day Light White
88992
12”
Day Light White
88994
12”
Day Light White
88978-1
12”
Night Vision Red
88992-1
12”
Night Vision Red
88994-1
12”
Night Vision Red
88978-2
12”
Blue
88992-2
12”
Blue
88994-2
12”
Blue
Dual Blue/White
88994-3
12”
Dual Blue/White
88978-3
12”
Dual Blue/White
88992-3
12”
Weld Mount
45
Marine Lights
360 Adjustable* & Fixed Anchor
Navigation Lights by Hella
Hella Marine LED Anchor Lights
Halogen Docking Lights by Beacon
360° NaviLED Anchor Lamp
Great for T-Tops, Towers, Poling Platforms
62255BLACK
8” Fold Down (Black)
62255WHITE
8” Fold Down (White)
8” Fixed Mount (Black)
62254BLACK
62253BLACK
4” Fixed Mount (Black)
*Can be mounted vertically or Horizontally
959910-727
959910-627
9-95-CMW
9-96-CMW
9-96-CMB
360° NaviLED Light
959731
959631
Spreader/Flood Light
TT402
TT406
Lumitec LED Rail Lights
LED T-Top/Utility Light
White/Bracket Mount
Fluorescent Light Kits
FL
Fluorescent Light
Mini Rail2
101078 6" White Output
101079 6" Blue Output
FLH
Large White
Small White
Small Black
24” Long; White Base
24” Long; Black Base
White/Flush Mount
12” Fold Down White
12” Fold Down Black
Fluorescent Light
Housing
Lumitec LED
Lumitec LED Dual Color
Spread/ Flood Light
101040 White/Bracket Mount
Soft Start & Dimmable
Dimmable, White/Bracket Mount
Round T-Top LED Lights
LED-WR
White & Red lights with silver aluminum case x 20”
Lumitec LED Underwater
Lights
2 color
101058
White+Blue Output
LED T-Top/Utility Light Rail2
101102 LED White/Blue
101103 LED White/Red
101057
101081 12" Dimmable
White+Blue Output
101243 12” - 3 Color
White, Red, Blue
Each color can come on
independent of others;
Only white is dimmable
Light Green
Output
46
Aluminum Marine Extrusions
High Quality Marine Pipe
6463 Marine Pipe comes Boxed and Poly-Sleeved
Suggested Applications: T-Tops, Tuna Towers, Half Towers, Marlin Towers,
Leaning Posts, Bow Rails, Poling Platforms, etc.
Western Extrusions: POLISHED Bright Dipped Anodized
SCH 40 Pipe x 23’ (6463-T66)
Stock Code
25-BDW-105A*
25-BDW-110A*
25-BDW-115
25-BDW-120
25-BDW-125
25-BDW-130
25-BDW-135
Size in Inches
3/4
1
1-1/4
1-1/2
2
2-1/2
3
Pcs/Box (Lin Ft/Box)
10 (230’)
6 (138’)
6 (138’)
5 (115’)
4 (92’)
2 (46’)
2 (46’)
Polished and
Bright Dipped
Western Extrusions: LITE BRUSHED Bright Dipped Anodized
SCH 40 Pipe x 23’ (320 grit) (6463-T66)
25-BRW-105B*
25-BRW-110B*
25-BRW-115
25-BRW-120
25-BRW-125
25-BRW-130
25-BRW-135
3/4
1
1-1/4
1-1/2
2
2-1/2
3
10 (230’)
6 (138’)
6 (138’)
5 (115’)
4 (92’)
2 (46’)
2 (46’)
Lite Brushed
and Bright Dipped
* Designed for 3/4” and 1” Sleeve Together
Pipe Aligners available on page 31
Western Extrusions: POLISHED Bright Dipped Anodized
SCH 80 Pipe x 23’ (6463-T66)
26-BDW-115
26-BDW-120
25-BD-125C
26-BDW-130
1-1/4
1-1/2
2
2-1/2
6 (138’)
5 (115’)
4 (92’)
2 (46’)
Western Extrusions: LITE BRUSHED Bright Dipped Anodized
SCH 80 Pipe x 23’ (320 Grit) (6463-T66)
26-BRW-115
26-BRW-120
26-BRW-215
1-1/4
1-1/2
2
6 (138’)
5 (115’)
4 (92’)
BON-L: POLISHED Bright Dipped Anodized
SCH 40 Pipe x 23’ (6463-T67)
Stock Code
25-BD-100
25-BD-105A*
MILL ORDER 25-BD-110A
25-BD-115
25-BD-120
Size in Inches
1/2
3/4
1
1-1/4
1-1/2
16 (368’)
12 (276’)
8 (184’)
6 (138’)
5 (115’)
BON-L: LITE BRUSHED Bright Dipped Anodized
SCH 40 Pipe x 23’ (320 Grit) (6463-T67)
25-BR-100
25-BR-105B*
25-BR-110B*
25-BR-115
25-BR-120
1/2
3/4
1
1-1/4
1-1/2
16 (368’)
12 (276’)
8 (184’)
6 (138’)
5 (115’)
SCH 40 Aluminum Pipe End Caps
Mill Finish
APC-100-MF 1
APC-125-MF 1-1/4
APC-150-MF 1-1/2
APC-200-MF 2
Anodized
APC-750
3/4
APC-100
1
APC-125
1-1/4
APC-150
1-1/2
APC-200
2
SCH 40 Black Plastic End Caps
RN1-1/4DBK1 1”
47
6463 Marine Pipe - 6463 Marine Pipe comes Boxed and Poly-Sleeved
Polished/Non-Anodized SCH 10 Marine Pipe (6463)
Stock Code
52-63-5179
Size in Inches
1-1/2 x 20’
6 (120’)
Mill Finish SCH 40 Marine Pipe (6463)
Stock Code
52-63-6926
52-63-6927
52-63-6928
52-63-6929
52-63-6930
52-63-6931
Size in Inches
3/4 x 23’
1 x 23’
1-1/4 x 23’
1-1/2 x 23’
2 x 23’
2-1/2 x 23’
12 (276’)
10 (230’)
6 (138’)
6 (138’)
4 (92’)
2 (46’)
Mill Finish Pipe
Mill Finish SCH 80 Marine Pipe (6463)
Stock Code
52-63-6933
52-63-6932
Size in Inches
2 x 23'
2-1/2 x 23'
2 (46’)
2 (46’)
Mill Finish Structural Pipe
Mill Finish SCH 10 Aluminum Pipe (6463-T67)
Stock Code
32-64-210
Size in Inches
2 x 23’
Pipe Aligners available on page 31
Stock Code
18-63-220
18-63-221
18-63-225
18-63-226
18-63-230
18-63-233
18-63-232
18-63-235
18-63-236
18-63-240
18-63-241
18-63-245
18-63-250
Size in Inches
3/4 x 20’
3/4 x 23’
1 x 20’
1 x 23’
1-1/4 x 20’
1-1/4 x 23’
1-1/4 x 24’
1-1/2 x 20’
1-1/2 x 23’
2 x 20’
2 x 23’
2-1/2 x 20’
3 x 20’
Stock Code
18-61-215
18-61-220
18-61-222
18-61-225
18-61-230
18-61-235
18-61-240
18-61-241
18-61-243
18-61-246
18-61-245
18-61-250
Size in Inches
1/2 x 20’
3/4 x 20’
3/4 x 24’
1 x 20’
1-1/4 x 20’
1-1/2 x 20’
2 x 20’
2 x 24’
2 x 30’
2-1/2 x 22’
2-1/2 x 20’
3 x 20’
SCH 40 Aluminum Pipe End Caps
Mill Finish
APC-100-MF 1
APC-125-MF 1-1/4
APC-150-MF 1-1/2
APC-200-MF 2
Anodized
APC-750
3/4
APC-100
1
APC-125
1-1/4
APC-150
1-1/2
APC-200
2
SCH 40 Black Plastic End Caps
RN1-1/4DBK1 1”
48
Bright Dipped Anodized Drawn Tube x 20’
Suggested Applications:
Bow Rails, Handrails, Canvas Top Frames, Bimini Tops, etc.
Stock Code
25-BD-460
25-BD-463
25-BD-465
25-BD-467
MILL ORDER 25-BD-468 (FL)
25-BD-469
Size in Inches
3/4 x .058
7/8 x .058 (16’)
7/8 x .058
7/8 x .058 (24’)
7/8 x .095
7/8 x .095 (24')
Lgths./Box
54
38
38
38
38
38
Drawn Tube
304 Superbuff Stainless Steel Tube
304 Alloy typically used in Freshwater applications
Stock Code
Size in Inches
25-304-100
7/8 x 24’ 2” - 16 gauge (.062)
25-304-105
1 x 24’ 2” - 16 gauge (.062)
Lgths./Box
30
16
Stainless Steel
Tube
316 Superbuff Stainless Steel Tube
316 Alloy typically used in Saltwater applications
Stock Code
Size in Inches
25-316-100
7/8 x 24’ 2” - 16 gauge (.062)
25-316-105
1 x 24’ 2” - 16 gauge (.062)
Lgths./Box
30
16
Oval Tube x 20’ (6463-T67)
Available: Polished and Bright Dipped, Brushed and Bright Dipped and Mill Finish
Applications: Ladder Steps, T-Top Braces, Tower Supports, etc.
Size in Inches
1 x 1-1/2 (Mill Finish)
1 x 1-1/2 (BDA Polished)
1 x 1-1/2 (BDA Brushed)
1 x 1-7/8 (Mill Finish) x 22’
1 x 1-7/8 (BDA Brushed)
1 x 1-7/8 (BDA Polished)
1-1/4 x 2-3/8 (BDA Polished)
1-1/4 x 3 (BDA Polished)
1-1/4 x 3 (BDA Brushed)
1-1/4 x 3 (Mill Finish)
1-1/4 x 4 (BDA Polished)
MILL ORDER 25-64-215 (FL) 1-1/4 x 4 (Mill Finish Brushed)
25-BR-215
1-1/4 x 4 (BDA Brushed)
25-64-216
1-1/4 x 4 (Mill Finish)
Stock Code
52-63-6354
25-BD-200
25-BR-200
25-MF-220
25-BR-205
25-BD-205
25-BD-208
25-BD-210
25-BR-210
25-MF-210
25-BD-215
Lgths./Box
10
10
10
8
8
8
6
6
6
6
4
4
4
4
Polished and Bright Dipped
49
Polished BDA Architectural Angle x 20’ - Smooth Finish
Stock Code
25-BD-300
Size in Inches
2 x 2 x 1/4
Lgths./Box
6 (Used to fabricate Brushed Mounting Angle)
Architectural Angle
Polished BDA Structural Angle x 20’ - Smooth Finish
Stock Code
25-BD-303
Size in Inches
2 x 2 x 1/4
Lgths./Box
6
Polished BDA Architectural Tee x 20’ - Smooth Finish
Stock Code
25-BD-305
Size in Inches
2 x 2 x 1/4
Lgths./Box
6
Structural Angle
Polished BDA Square Tube w/ Radius Corner x 20’
Stock Code
25-BD-310
25-BD-315
Size in Inches
1 x 1 x 1/8
2 x 2 x 1/8
Lgths./Box
10
6
Polished BDA Rectangular Tube w/ Radius Corner x 20’
Stock Code
25-BD-320
25-BD-325
Size in Inches
1 x 2 x 1/8
1 x 3 x 1/8
Architectural Tee
Lgths./Box
8
6
6463-T6 Polished BDA Flat Bar x 12’ (Sharp Corner)
Stock Code
25-BD-415
25-BD-400
25-BD-405
25-BD-410
25-BD-417
25-BD-416
Size in Inches
1/8 x 4
1/4 x 2
1/4 x 3
1/4 x 4
3/8 x 4
3/8 x 5
Lgths./Box
16
16
10
8
4
4 (used for Outrigger Bases)
Square Tube w/Radius
Mini Plate - Brushed (320 Grit) and Bright Dipped Anodized
Stock Code
25-BRW-415
Rectangular Tube w/Radius
Size in Inches
1/4 x 12” x 48” (Used to make: Brackets, Mounting Plates, Braces & more)
6463-T6 Brushed (320 Grit) BDA Flat Bar x 12’ ( Sharp Corner)
Stock Code
25-BRW-400
25-BRW-405
25-BRW-410
Size in Inches
1/4 x 2
1/4 x 3
1/4 x 4
Lgths./Box
16
10
8
Flat Bar (Sharp Corner)
6463-T6 Polished BDA Flat Bar x 12’ ( Radius Corner)
Stock Code
25-BD-420
25-BD-425
25-BD-428
25-BD-430
Size in Inches
1/4 x 2
3/8 x 2
1/2 x 1-1/2
1/2 x 2
Lgths./Box
16
10
12
8
Flat Bar (Radius Corner)
6463-T6 Flat Bar x 12’ Mill Finish ( Sharp Corner)
Stock Code
10-64-340
10-64-345
10-64-350
10-64-353
10-64-355
10-64-358
Size in Inches
1/4 x 2
1/4 x 2-1/2
1/4 x 3
1/4 x 3-1/2
1/4 x 4
1/4 x 4-1/2
Stock Code
10-64-360
10-64-365
10-64-440
10-64-443
10-64-445
Size in Inches
1/4 x 5
1/4 x 6
3/8 x 4
3/8 x 5
3/8 x 6
50
Outrigger Oval Extrusion x 20’
Stock Code
25-BR-211
Size in Inches
1-1/4 x 5.516 (BDA Brushed)
Lgths./Box
4
Outrigger Oval Extrusion
Polished and Bright Dipped Oval Tube with Ribs x 20’ (6463-T66)
Applications: Ladder Steps, T-Top Braces, Tower Supports, etc.
Stock Code
Size in Inches
Lgths./Box
MILL ORDER
1 x 1-1/2 (3 Ribs) - Minimum Quantity Required
25-BD-245
1 x 1-1/2 (7 Ribs)
10
Polished and Bright Dipped Oval
(3 Ribs: left; 7 Ribs: right)
Polished and Bright Dipped Oval Tube x 20’ - Non Skid (6463-T67)
Applications: Ladder Steps, T-Top Braces, Swim Platforms, etc.
Non-Skid Finish on Both Flat Surfaces, All other surfaces are Polished
Stock Code
Size in Inches
Lgths./Box
25-NS-200
1 x 1-1/2 (Non Skid)
10
25-NS-205
1 x 1-7/8 (Non Skid)
8
25-NS-215
1.29 x 1.757 Tower Step x 20’
8
25-BD-226
3" Knurled Ladder Rung x 12'
25-MF-226
3" Knurled Ladder Rung x 12' (Mill Finish)
DVLDR
Black Dive Ladder End Caps
Polished and
Bright Dipped
Non-Skid
Tower
Step
3” Knurled Ladder Rung
Polished and Bright Dipped Oval Tube x 20’
Polished and Bright Dipped Oval Tube
(w/ Slot for Insert) left to right: 25-BD-250,
25-BD-255, 25-BD-212
w/ Slot for Insert ( 6463-T67 )
Stock Code
Size in Inches
Lgths./Box
25-BD-250
1 x 1-1/2 (slot for small insert)
10
25-BD-255
1 x 1-7/8 (slot for large insert)
8
25-BD-212
1-1/4 x 3 (double slot for small insert)
6
Insert Material
Stock Code
VI-SM
VI-LG
Description
1-1/2 (mates with 25-BD-250 & 25-BD-212)
1-7/8 (mates with 25-BD-255)
Insert Material
Bright Dipped Anodized Awning Track x 16’
25-BD-470
Awning Track x 16’
Awning Track
Bright Dipped Anodized Slide Track Channel x 14’
25-BD-475
Slide Track Channel
Slide Track Channel
Gunwale/Gunnel - 6061-T6
Suggested Applications: Boat Gunwales/Gunnels, Airboat applications
52-61-672
2.2 x 2 x 1/8 x 32' Mill Finish
0.850
Gunwales/Gunnel
110 SW 12th Avenue • Dania Beach, FL 33004
Phone: 954-462-0917 • Fax: 954-524-0441
tigress@easternmetal.com
TIGRESS WARRANTY
Tigress Trading Co., Inc. products are warranted against material and/or manufacturing defects for a period of 1 year, from
date of purchase. This warranty is limited to the repair and/or replacement of merchandise that proves to be defective in
material and/or workmanship. Note: proof of purchase must accompany all products submitted for warranty.
Alignment Pins
Back Rest Components
Blind, Mount, Round, Pivoting
& Oval Rod Holders
Bracket Mount, Center Mount & Weld Mount
LED Lighting
Breakaway Pins
Bright Dipped Anodized Drawn Tube
Brushed Bright Dipped Anodized Pipe
Cup Holders
Economy Stainless Rod Holders
Electric Top Mounts
Female & Male Pins, Half Pins
Fiberglass Boxes
Fiberglass Hard Top
Folding Bench Seat
Foot Rest Hardware
Gunnel & Center Rigger Systems
Gunnel & Side Mount, Outrigger Holders
& Accessories
Gunnel, Pivoting & Side Mount Rod Holders
Hard Top Bushings & Washers
Heavy Duty Bearing Style Hinges
Hinge Brackets
Inline & Hand Rail LED Lighting
Kite Rod Holders & Accessories
Kites & Accessories
LED Strip Lighting
Manual Top Mounts
Marine Lights
Page 32
Page 27
Page 29
Page 19
Page 44
Page 30
Page 48
Page 46
Page 42
Page 21
Page 29
Page 20
Page 5
Page 33
Page 34
Page 34
Page 32
Page 32
Page 12
Page 8
Page 18
Page 29
Page 21
Page 32
Page 41
Page 16
Page 15
Page 43
Page 6
Page 45
Mill Finish Pipe
Misc. Extrusions & Marine Grade Sheet
Miscellaneous Pads
Mounting Angles
Mounting Pads & Bow Rail Components
Outrigger Snubbers & Accessories
Pipe Aligners
Pipe Size Chart
Polished Bright Dipped Anodized Pipe
Polished Bright Dipped Anodized Extrusions
Polished Bright Dipped Anodized Pipe
Polished Bright Dipped Oval Tube
Rectangular Pads
Rigging Kits
Rod & Reel Hangers
Rod Holder & Chair Accessories
Rod Holders Backing Plates & Accessories
Round Brushed Pads
Round High Polished Pads
Round Mill Finish Pads
Round Polished Pads
Sleeves
Specialty Pads
Stainless Steel Tube & Oval Tube
Telescoping & Fixed Outrigger & Accessories
Telescoping Outriggers
Tigress Kite Set Up
Top Mount Outrigger Holders
Top Mounts & Clamp-On Systems
Tower Boss
Triple, Bolt-On & Transom Rod Holders
Page 47
Page 50
Page 39
Page 30
Page 31
Page 14
Page 31
Page 23
Page 46
Page 49
Page 47
Page 50
Page 38
Page 13
Page 26
Page 25
Page 22
Page 36
Page 36
Page 37
Page 35
Page 31
Page 31
Page 40
Page 48
Page 10
Page 9
Page 17
Page 7
Page 11
Page 33
Page 28
954-462-0917 • tigress@easternmetal.com • www.tigressoutriggers.com

Tigress Catalog - Eastern Metal Supply

Transcription

Similar documents

Complete Marine Products Section

The Train Depot Price List