Muestrario de refacciones Ryobi®

Muestrario de refacciones
Ryobi®
Intrucciones
1. Identifique la figura (Drawing #) de la sección de su interés.
2. Identifique el número en la figura (Key #) de la parte que busca .
3. Utilice el número en la figura para identificar el número de parte (Part #) en la/s
página/s siguientes.
4. Ingrese a www.equiposgraficos.com y complete el formulario de cotización
incluyendo el número de parte y descripción.
5. Solicite asistencia a cristyg@egomexico.com o al +52(55) 5396 6580
Gracias por su compra
EFFECTUS GRAPHICUS ORTUS S.A. DE C.V.
www.equiposgraficos.com
Salónica 259 Col. Sector Naval. México D.F. 02080
Tel: +52 (55) 5396 6580
Replacement parts for: RYOBI 2700, 2800, 3200, 3200AN/CD/NP, 3302M, 480/520/560
PART #
1
3
2
1) FILTER FELT
PART #
P-30201
4.00
2) GASKET SEAL
P-1937
6.70
3) WICK For oil jar
P-1155
1.50
SUCKER FEET
Standard
P-5208
.80
••• Treated with ink resistant repellent for less ink tracking.
SUCKER FEET
PUMP REPAIR KIT - 2700, 2800, 3200
P-31120
Consists of: 4 Vanes / 2 Filters / 1 Oil wick /
2 Ball bearings / 1 Oil seal
329.90
PUMP REPAIR KIT - 520/522/530/560
P-31130
319.90
Consists of: 4 Vanes / 2 Filters / 2 Ball bearings /
1 Urethane gasket / 1 Fiber gasket / 8 Paper gaskets /
2 Timing belts
(Only one of each item depicted here)
PUMP VANE
••• MADE OF “GROUND STAINLESS STEEL”
(27.5 mm x 115 mm)
P-9448
34.90
VARIABLE SPEED PULLEY
P-1491
249.90
SPEED CONTROL & FEEDER HAND CRANK
••• Improved style works on 2700, 2800, 3200.
HOSE
For side blowers
For compressor filter
For rear blower
For sucker tube manifold
E
A&B
C
31.90
P-5265
P-5299
P-5288
P-1188
4.90
11.20
7.00
6.00
P-27087
P-32087
P-2652
24.40
24.40
9.90
SHEET SEPARATOR
Brass
Copper
P-27114
P-27117
1.00
1.20
SHEET SEPARATORS
(A) 522
(B) 522PF / PFH
P-522114
P-522114PF
3.00
10.90
4.20
8.90
P-97471
P-33478
P-33471
6.50
10.90
14.00
BACK PAPER GUIDE ASSEMBLY
2700, 2800, 3200, 3200MCD
COMPLETE
P-27081
(A) Screw w/ sems washer P-2328
(B) Block
P-27221
(C) Bracket
P-27090
(D) Back guide spring
P-27712
(E) Screw
P-2327
71.90
.60
10.80
34.90
25.80
.60
SPRING BASE For P-27088 shown below.
2
FEEDER CLAMP
5.5 mm slide plate slots
7 mm slide plate slots
ADJUSTING SCREW
7.00
4.60
GUIDE SPRING
975 PFA
(Thick)
(Thin)
D
P-98060
P-5241
P-7580
THUMB SCREW For sheet separator bracket
P-2909
THUMB SCREW For master cylinder tail clamp
2700, 2800, 3200
P-2903
69.90
TIMING BELT - For main pump
520, 522, 530, 560
P-3811
(A) 500K, 512
(B) 480N, 480K
1
P-27100
33.90
1) BACK PAPER GUIDE
P-27537
9.90
2) SIDE PAPER GUIDE
P-27088
10.50
PAPER RETAINER - 3302
Located under upper feed roller.
P-33143
26.90
PAPER GUIDE HANDLE STOPPER
950, 960
P-95124
14.90
P-33500
P-33420
P-33433
22.50
23.90
22.50
slide thickness
SLIDE PLATE For feeder clamp
5 mm slide thickness
6.5 mm slide thickness
P-27089
P-32089
SLIDE PLATE & FEEDER CLAMP KIT
P-39087
BUMPER For air control latch
P-5283
49.90
56.90
83.80
3.20
HEIGHT CONTROL SCREW - For paper leveling bar.
P-8144
15.90
COUPLING JOINT
13
P-6776
12.10
SUCKER TUBE
P-27174
12.50
SCREW HOLDER
P-27966
9.10
PAPER RETAINER
Feeder 3302
Conveyor .008 thick
Conveyor .012 thick
FEED TAPES (sold individually—not in sets)
480K/N, 500N/NP
P-3935
3302 s/n up to 4432
P-3939
3302 s/n 4433 to 7036
P-3936
3302 s/n 7037 & Up
P-3870
39.90
32.00
32.00
39.90
FEED SENSING SWITCH
R-3302, I-3985
29.90
P-4050
Solo una muestra de nuestro catalogo www.equiposgraficos.com
ITEK 530, 560, 950, 960, 975.....................................................Continued thru page 16.
PART #
C
A
D
D
B
FEELER FINGER SHAFT
Complete 2700, 2800
Complete 3200
(A) Shaft only 2700, 2800
(A) Shaft only 3200
(B) Lever
(C) Latch
(D) Roll pin
RUBBER FEED ROLLERS
2700, 2800
3200
2
1
P-27138
P-32138
P-27139
P-32139
P-27719
P-27141
P-2834
P-27157
P-32157
PART #
P-27245
P-33245
8.00
14.90
PAPER STOP FINGER
1) 2700, 2800
2) 3302
P-27241
P-33241
6.00
9.90
P-33237
19.00
SKID ROLLER ASSEMBLY - 3302
Operators side (shown)
P-33562
Non-operators side
P-33568
134.90
134.90
SPRING - Imp. cyl. latch
P-27791
ADJUSTING NUT For blanket cylinder clamps
Right hand thread
P-5303
Left hand thread
P-5312
P-27327
9.90
LATERAL ADJUSTING SCREW For head clamp
P-2917
13.90
SPRING (Plate Cylinder)
P-33365
4.90
P-27323
P-32323
P-32333
P-33323
105.80
116.90
110.00
97.50
179.90
179.90
IMP. GRIPPER FINGER
1) 2700, 2800, 3200
2) 3302 (urethane tip)
FEED DRUM FINGER
(urethane tip)
TAIL CLAMP SPRING
99.90
169.90
62.90
115.90
19.00
29.90
.60
9.50
25.80
25.80
TAIL CLAMP
2700, 2800
3200 CD/NP
3200 17-1/4” IMAGE
3302
LOCK PIN on Plate CylinderP-4543
29.90
HEAD CLAMPS For Ryobi 3302
••• DIAMOND COATED FOR SURE GRIP AND LONGER LIFE.
Top bar (shown)
P-33788
Short clamp (Operators side)
P-33771
Short clamp (Non-operators side)
P-33760
PIN For P-33788 shown above.
Ser. # 6186 & lower (3mm small O.D.)
Ser. # 6187 & higher (5mm small O.D.)
P-4773
P-4789
490.00
162.50
162.50
7.00
4.90
WATER CONTROL LEVER
A
3200 MCD
P-320416
32.00
B
C
WAVER ROLLER TENSION SPRING
P-38413
D
STANDARD BLANKET BARS
2700, 2800 Complete
R-3200, I-975 Complete
R-3302, I-3985
(A) Upper blanket bar 2700, 2800
(A) Upper blanket bar R-3200, I-975
(A) Upper blanket bar R-3302, I-3985
(B) Lower blanket bar 2700, 2800
(B) Lower blanket bar R-3200, I-975
(B) Lower blanket bars R-3302, I-3985
(C) Mounting screw
(D) Clamping screw
P-27252
P-32252
P-33252
P-27258
P-32258
P-33258
P-27256
P-32256
P-33256
P-2216
P-2206
220.00
222.00
167.90
71.90
54.00
82.00
65.90
62.00
78.90
.60
.60
WATER OSCILLATOR SHAFT ASSEMBLY - 2700, 2800
Complete
P-27460
Shaft only
P-27460-S
Dog
P-27463
Worm
P-27464
Roll pin
P-382
SPLASH GUARD SHIELD P-27376
SPLASH GUARD KIT
P-27376-K
Consists of 2 shields plus hardware.
QUICK CHANGE BLANKET BARS
••• Bars remain on your cylinder while you make a 5 minute blanket change.
Closed cylinder 1/2” gap (19” blanket size)
950, 960 / 2700, 2800
Open cylinder 4” gap (19-1/2” blanket size)
2700XL, 2800XL
975 / 3200
985 / 3200 MCD
975 / 3200XL,XLD,CPD
3985 / 3302
P-30310
210.00
P-30047
P-30037
P-30038
P-30311
P-30221
341.25
193.05
209.65
341.25
390.00
4.90
299.90
184.90
44.00
63.80
.60
3.00
22.90
WATER BOTTLE STOP
SPRING for cap assy.
P-7621
P-27543
8.20
4.90
BEARING HOUSING
P-27322
66.90
WATER DUCTOR LATCH
2700, 2800
P-27546
6.00
Solo una muestra de nuestro catalogo www.equiposgraficos.com 14
Replacement parts for: RYOBI / ITEK...................................Continued from page 13.
PART #
PART #
ADJUSTING SCREW For ink fountain
R-2700, 2800, 3200, 3302
WATER FOUNTAIN ROLLERS
2700
3200
P-27364
P-32364
P-2925
7.00
204.00
390.00
OSCILLATING SHAFT ASSEMBLY - INK 2700
INK WASH UP BLADE
950, 960, 2800 - 30.3 cm Long (6 Holes)
3200, 3302, 3985 - 35.9 cm Long (6 Holes)
P-30224
P-30225
14.90
14.90
INK FOUNTAIN BLADES
2700, 950 - 29.5 cm x 9.0 cm (Ser.16331 & up)
2700, 950 - 28.6 cm x 7.0 cm (Ser.16330 & down)
3200 CD/NP - 32.0 cm x 9.0 cm
3200 MCD/MNP- 34.6 cm x 9.0 cm
500N / NP - 49.2 cm x 85.7 cm
P-27233
P-95233
P-32233
P-32233M
P-50079NP
77.90
82.90
89.90
86.00
79.00
Complete
Shaft only
Roll pin
Dog (comes with P-27249)
Worm (comes with P-27249)
P-27462
P-27472
P-2834
P-27463
P-28464
204.90
73.80
.60
44.00
63.80
Dog & Worm set
P-27249
94.00
DOG & WORM KIT
DOG (Ink & Water 950, 2700)
WORM (Ink & Water 950, 2700)
P-27874
P-27463
P-27464
94.00
44.00
63.80
DOG (Ink & Water 960, 2800)
WORM (Ink 960, 2800)
WORM (Water 960, 2800)
P-27463
P-27464
P-28464
44.00
63.80
63.80
BUSHING For ink oscillating roller
P-3203
14.00
KEY For drive shaft clutch pulley
P-11652
2.00
WASH UP TRAY ASSEMBLY
2700/2800
3200/3202
3302
INK FOUNTAIN WIRE
950, 960, 2700, 2800
3200, 3302
P-27773
P-32773
P-33773
219.90
169.90
289.90
P-37084
P-32084
2.90
1.70
BUSHING For ink fountain roller
P-3268
INK IDLER GEAR
9.90
DRIVE SHAFT AND GEAR ASSEMBLY
Complete 2700, 2800
Complete 3200
Complete 3302
Shaft only 2700, 2800
Shaft only 3200
Shaft only 960PFA, 3200PFA
Shaft only 3302
Gear only 2700, 2800, 3200 (not 3200PFA)
Gear only 3302
Taper pin 2700, 2800, 3200
Taper pin 3302
P-27577
P-32577
P-33577
P-27583
P-32583
P-32583PFA
P-33583
P-27581
P-33581
P-451
P-2849
289.90
340.00
243.90
143.90
170.00
199.90
110.00
104.90
110.00
.60
2.00
P-27509
144.90
(A) I-950/960
P-95607
43.90
COUNTER
P-27954
129.00
(B) R-27/28/3200 Sers.
P-27607
43.90
INK DUCTOR SPRINGS
Operators side
Non-operators side
Screw
Washer
Arm
P-2521
P-2700
P-27956
.60
.60
26.00
P-27338
P-27336
3.50
2.40
IDLER GEARS
On ejector roller
P-27636
57.90
P-27629
57.90
INK DUCTOR ARMS
INK RATCHET PAWL
BUSHING For idler rollers
P-27268
P-3207
39.80
24.90
For C/D drive sprocket shaft
GEAR STUD For Chain Delivery drive gear
P-7939
16.00
ADJUSTING SCREW For ink fountain
ITEK 950, 960
P-2021
5.20
SWITCH BODY For control panel
R-3302, I-3985
15
P-9830
Solo una muestra de nuestro catalogo www.equiposgraficos.com
39.90
Replacement parts for: RYOBI / ITEK...................................Continued from page 13.
PART #
PART #
OFFSET DUPLICATOR LAMP (Long neck)
950, 960, 2700, 2800
P-9865
99.80
Lamp comes with plug and can be plugged into any
standard 115v wall outlet. Some models of Ryobi may
need lamp wired directly to press.
GUIDE
P-272281
22.00
FRONT GUIDE
P-272420
83.90
••• CAN USE UP TO 100 WATT BULB.
LED LAMP - On sub control box.
R-3302, I-3985
P-9707
30.00
DELIVERY TABLE SENSING SWITCH
R-3200, I-975
CARRIER LINK
For gripper bar
P-8738
14.00
GRIPPER CHAIN (1 only)
59” long
P-8939
100.00
54” long
P-8938
160.00
NOTE: Please measure your chains end to end.
Chain connecting link
P-1540
2.90
P-8745
22.50
CONNECTING LINK
R-3302, 3304 / I-3985
C
B1
A
D
E F
G
O&P&Q
N
H
S
K
I
R
J
U
B2
T
L
M
GRIPPER BAR ASSEMBLY
Complete 2700, 2800
Complete 3200
Complete 3302
P-270990
P-320990
P-330990
439.90
399.90
495.00
(A)
(B1)
(B2)
(C)
(D)
(E)
(F)
(F)
(G)
(G)
(H)
(I)
(J)
(J)
(K)
(L)
(M)
(N)
(O)
(P)
(Q)
(R)
(S)
(T)
(T)
(U)
P-320991
P-2810
P-2805
P-271040
P-2832
P-2103
P-271020
P-331020
P-281080
P-331080
P-2511
P-1487
P-271060
P-321060
P-271092
P-320992
P-1803
P-2752
P-2702
P-2602
P-7920
P-2833
P-271061
P-271091
P-321091
P-11435
52.90
.90
.60
29.90
.60
.60
11.50
38.85
2.30
2.90
.60
9.90
12.40
10.90
21.90
52.90
6.50
.60
.60
.60
6.30
.60
6.40
31.90
34.90
5.70
Right hand bracket
Taper pin
Taper pin
Gripper arm
Roll pin
Screw
Gripper finger (no urethane)
Gripper finger (urethane tip)
Spring (2 on 2700, 2800, 3200)
Spring (4 on 3302)
Set screw
Collar
Gripper finger shaft - 2700, 2800
Gripper finger shaft - 3200
Center bracket
Left hand bracket
Ball bearing
C-Ring
Lockwasher
Nut
Stud
Roll pin
Gripper pad
Shaft - 2700, 2800
Shaft - 3200
Collar
P-9815
V-BELT For Ryobi / Itek
For compressor
P-1678
For clutch pulley
P-1687
Motor to pump
P-1695
Motor to pump 3202M
P-4905
Motor to pump 950, 960
P-4907
Drive motor 3200 (60Hz)
P-4910
Drive motor 3200 (50Hz)
P-4986
••• All sizes available 2L, 3L, 4L, 5L
DOLLY BOARD
Complete
Board only
Caster
Washer
Screw
18.90
(28”)
(31”)
(34”)
(36”)
(38”)
(42”)
(41”)
8.00
8.00
7.50
9.90
9.00
10.50
16.00
ASSEMBLY - RYOBI 3302
P-332440
214.00
P-332500
174.50
P-1641-S
19.90
P-569
.60
P-10342
.60
••• Eliminate costly downtime with your own emergency kit
for your model press.
(Master Kit does not include Spring Kit)
REPAIR KITS FOR RYOBI
Master kit
P-30376 - 513 pcs 239.80
Pin kit
P-30375 - 168 pcs. 99.90
Ring kit
P-30374 - 104 pcs. 55.80
Nut kit
P-30373 - 38 pcs.
21.80
Washer kit
P-30372 - 68 pcs.
49.90
Screw kit
P-30371 - 132 pcs. 77.90
Spring kit
P-31128 - 39 pcs. 129.90
• • • • • • • • • PARTS FOR ITEK • • • • • • • •
GEAR- For 1015/1117 Plate Maker
Tank roller frame ass’y.
P-1015010
7.50
GEAR- For 1015/1117 Plate Maker
Tank roller frame ass’y.
P-1015020
7.50
GEAR- For 1015/1117 Plate Maker
Tank roller frame ass’y.
P-1015030
7.50
GEAR- For 1015/1117 Plate Maker
Tank roller frame ass’y.
P-1015040
8.70
GEAR- For 1015/1117 Plate Maker
Tank roller frame ass’y.
P-1015050
7.00
SPRING- For 1015/1117 Plate Maker
Tension rollers
P-1015200
3.90
BACK STOP BRACKET (Chain Delivery)
2700, 2800, 3200
P-272422
29.90
SPRING- For 1015/1117 Plate Maker
Tension rollers
P-1015210
6.90
Solo una muestra de nuestro catalogo www.equiposgraficos.com 16