unitile - United GI Products Sdn. Bhd.

UNITILE
the European asymmetrical tile-effect steel roof
UNITILE
®
STEEL ROOFING
UNITILE
®
Using Scandinavian Technology to create asymmetrical feature.
Double Protection from water seepage with anti-capillary groove & inner
drainage valley.
With overlaps that appears almost seamless.
Last 4 times more than ordinary steel roofing and not easily
affected by "tropical staining".
19mm rib height, can withstand heavier load.
Higher resistance to colour fading.
MATERIALS
QUALITY CONTROL
UNITILE® is readily available in BlueScope Steel G300 Clean COLORBOND® steel.
Clean COLORBOND® steel, AZ150 G300
Clean COLORBOND® is the pre-painted ZINCALUME® steel with the ability to
prevent tropical dirt staining and better colour retention. Clean COLORBOND®
paint system is oven cured with nominal gloss of 25% which conforms to
Australian Standard AS2728 Category 3. It is certified to BOMBA Class ‘O’
(AS1530) with heat resistance up to 100° C.
Other materials are also available upon request;
• Clean COLORBOND® ULTRA AZ200 G300 steel.
• Clean COLORBOND® XPD Pearlescent AZ150 G300 steel.
• PrimaMaju AZ100 G300 steel.
Finish Coat
Corrosion Inhibitive Primer
Conversion Coating
ZINCALUME® AZ150 Steel
Conversion Coating
Corrosion Inhibitive Primer
Backing Coat
With the certification of MS/ISO 9001: 2000 Quality Management System, UGI
ensures high quality Clean Colorbond® is precisely cold formed into UNITILE®.
WARNINGS
• Minimum recommended roof pitch for UNITILE® is 7°.
• Copper and Lead are incompatible materials and should NOT be used with
UNITILE® made from Clean Colorbond® Steel.
• Use only acetic-free sealant on UNITILE® sheets
• Manual cutting is recommended. Avoid circular saw cut that result in having
hot particles falling onto UNITILE® sheets.
• While walking on UNITILE®roof, evenly distribute weight to avoid
concentrating weight on either heels or toes. Use smooth soft soled shoes.
PHYSICAL PROPERTIES
Mass & Yield
TCT
Total Coating Thickness
Kg/m
Kg/m2
m2/t
0.41mm
2.73
3.74
267
0.48mm
3.29
4.50
222
STORAGE
SCHEMATICS & LENGTHS
UNITILE® is produced in length up to 9m. However longer length is available
provided transport and 0n-site handling cna be arranged.
Keep roofing sheets dry and clear off the ground in a well ventilated area with
proper cover. This is to avoid accumulation of moisture on the roofing sheets
and to avoid contact with any corrosive agent such as chemicals, solvents or
noxious vapours.
350mm
ROOF BATTEN
19mm
762mm
The correct positioning of roof battens for UNITILE® is shown in the diagram.
The recommended batten spacing is positioned at the middle of the module.
350mm
TOLERANCES
Length + / - 10mm
Cover width + / - 4mm.
350mm
COLOURS
UNITILE® is readily available in popular Clean COLORBOND® Steel Colours. Colour matching is possible upon meeting a minimum order quantity.
Autumn Red
Lazurite Blue
Leather
Beige
Almond Beige
Gull Grey
Caulfield Green
Aquamarine
Gun Metal Grey
Armour Grey
LAYING
THERMAL & NOISE INSULATION
Laying begins at the gable side and from left to right (view from gutter to ridge).
Whenever possible, install the female rib first and subsequently fit the male rib
into the female rib. Before laying commences the dimensions of the under
laying structure must be thoroughly checked. The sheet must always be laid at
right angles to eaves. The first sheet on a roof must be laid with particular care
because it determines the lay of the subsequent sheets.
SIDE LAPPING
The correct side overlap ensures 100% water leakage proof and enhance
unique UNITILE® appearance.
INCORRECT
CORRECT
FASTENING DETAILS
To match the performance of UNITILE®, the fasteners must conform to
AS3566 Class 3.
CREST FIXING
Drilling Capacity <6.0mm
w/out insulation - CTEKS 12-14 x 50 HGS
with insulation - CTEKS 12-14 x 68 HGS
Hardwood
w/out insulation - CT17 12-11 x 50 HGS
with insulation - CT17 12-11 x 65 HGS
SIDE FIXING (stitching)
Drilling Capacity <2.5mm
CSP 14-14 x 22 HWFS
ACCESSORIES
UNILINE® Rain Gutters, Ridge Capping, Valley Gutter, Wall Flashing are
available to match UNITILE® Roofing.
UNILINE©
Ridge Capping
Valley Gutter
WARRANTY
Wall Flashing
UNITILE® has a back to back material performance warranty from BlueScope
Steel Malaysia of up to 25 years upon meeting all the requirements. The warranty
includes;
• Ability to resist dirt staining up to 5 years.
• No cracking, flaking or peeling up to 10 years*.
• No perforation due to corrosion up to 25 years*.
* denotes under normal well-washed exposure condition.
UNITILE® is best installed with proper thermal and noise insulation. A good
practice is to lay a layer of wire netting over battens, then a layer of double
sided aluminium foil, followed by a 50mm 40kg/m3 ROXUL® Rockwool, and
finally UNITILE® roofing sheets.
"Our new roof has greatly
enhanced the value of our house.
Not only that, the roof gives us
flexibility to suit our lifestyle."
Lot 835, Block 7, Jalan Demak Laut 3,
Demak Laut Industrial Park, 93050.
PO Box 472, 93710 Kuching.
Sarawak, Malaysia.
T +6 082 439 257
F +6 082 439 259
E info@ugi.com.my
AUTHORISED DEALER
© 2009 United GI Products Sdn Bhd. All rights reserved. UGI logo, UNIDEK®, UNISPAN®, UNITILE®, UNILOK®, UNICORTM and UNILINE® are trade marks of United GI Products Sdn Bhd., registered in Malaysia. ZINCALUME® and Clean COLORBOND® are trade marks of BlueScope Steel Limited. The clean COLORBOND® steel colours shown in this
catalogue have been reproduced to present actual product colours as accurately as possible. However, we recommend you to check your chosen colour against an actual sample of the product, as varying light conditions and limitations of the current printing process may affect colour tones. No part of this brochure may be reproduced or
transmitted in any form by any means, electronic, mechanical, photocopying, recording or otherwise, with written permission of United GI Products Sdn Bhd. All information and product specifications are current at the time of printing and subject to change without notice. January 2006. DOC ID: UGI UNIDEK Catalogue Ver:2 Rev:1.
ugi.com.my