Catalogo General Bombas Centrifugas ETANORM KSB

Transcription

Product Introduction
1211.1/14-10
G4
50 and 60 Hz
Etanorm/Etanorm-R
Standardized Pumps
Fields of Application
Water supply
Fire-fighting systems
Sprinkling
Irrigation
Drainage
Heating
Air-conditioning systems
Drinking water
Service water
Hot water
Shaft Seal
Cooling water
Swimming pool water
Sea water
Fire-fighting water
Brackish water
Condensate
Brine
Oils
Cleaning agents
Fluid
Pure liquids not chemically or mechanically aggressive to the
pump materials.
Operating Data
Q
H
t
p2
Designation
EN(-R) 40 - 160 43 (6238) G 10 *)
Type series Etanorm
Pump size, e.g.
Actual impeller diameter - 100 mm, e.g. 143 mm
= (angular reduction of impeller vanes)
e.g. actual diameter 162/138 mm =
Casing material, e.g. JL 1040 2)
Shaft seal, e.g. mechanical seal Q1 Q1 X4GG
2) to EN 1561 = GJL-250
*) for Etanorm only
Accessories
Drive
Surface-cooled KSB-IEC three-phase squirrel cage motor
up to 1900 m3/h, (528 l/s)
up to 102 m
-30 °C to +140 °C
up to 16 bar 1)
Winding:
1) see pressure/temperature limits given on page 5 of type series booklet 1211.5/9-10.
Design
Horizontal volute casing pump, single-stage (pump size
125-200/2 two-stage), with power ratings and main dimensions
to EN 733 up to DN 200 / extension Etanorm-R, with bearing
bracket, in back pull-out design.
Shaft with replaceable shaft sleeve/shaft protecting sleeve in
the shaft seal area.
Volute casing and impeller with replaceable wear rings.
Volute casing with integrally cast pump feet.
Bearings
Deep-groove ball bearings, grease-lubricated.
DIN EN ISO 9001
Mechanical seal to EN 12756 (Stanard for Etanorm, for Etanorm-R as option) or gland packing.
up to 2.2 kW: 220-240 V/380-420 V
3 kW and above: 380-420 V/660-725 V
Design:
IMB 3
Enclosure:
IP 55
Thermal class: F with temperature sensors: 3 PTC
resistors
Operating mode: continuous operation S1
or
surface-cooled three-phase squirrel cage motor as described
above, but West European brand to KSB’s choice.
Coupling
Flexible coupling with/without spacer sleeve
Contact Guard
Coupling guard as per EN 294.
Baseplate
Sectional steel / folded steel plate, fabricated sectional steel
for the complete unit (pump and motor)
in torsion-resistant design
General Member of
www.bymisa.mx , Email ventas@bymisa.mx
Etanorm/Etanorm-R
Selection charts
Etanorm
n = 2900 1/min
20
30
40
20
120
50
30
US.gpm
40
50
100
200
IM.gpm
300
100
400
200
500
300
1000
400
2000
500
3000
1000
2000
100
300
32--250
4)
32--250.1
1) 2)
1) 2)
80--250
65--250
50--250
40--250
2) 3) 4)
100--250
1) 2)
1) 2)
1) 2)
200
50
65--200
32--200.1
40--200
1) 2) 4)
50--200
1) 2)
40
32--200
32--160.1
30
1) 2)
80--200
1) 2)
1) 2)
100--200
1) 2)
125--200
1) 2)
1) 2) 4)
1) 2) 4)
100
40--160
32--160
50--160
1) 2)
65--160
1) 2)
1) 2)
80--160
1) 2)
1) 2)
100--160
1) 2) 4)
20
32--125
32--125.1
1) 2) 3) 4)
40--125
50
50--125
65--125
40
10
30
ft
20
Lieferbar auch in: / Also available in: / Egalement livrable en: / Anche consegnabile in: / Ook leverbaar in: / También disponible en:
1) Zinnbronze / Tin bronze / Bronze ordinaire / Bronzo allo stagno / Tinbrons / Bronce al estaño
2) Sphaeroguss / Spheroidal graphite cast iron / Fonte nodulaire / Ghisa sferoidale / Nodulair gietijzer / Fundiciõn esferoidal
Nicht lieferbar in: / Not available in: / Néxiste pas en: / No consegnabile in: / Niet leverbaar in: / No disponible en:
3) Chrom--Nickel--Molybdaen--Stahlguss / Cast chrome nickel molybdenum steel / Acier coulé au nickel--chrome--molybdène / Acciaio fuso al cromo--nickel molibdeno /
Chroom--nikkel--molybdeen gietstaal / Acero fundido al cromo--niquel molibdeno
4) Ergaenzungsgroessen in EN 733 nicht enthalten / Supplementary sizes not included in EN 733 / Les tailles complémentaires ne sont pas couvertes par EN 733 /
Grandezze suppplementari non incluse in EN 733 / Aanuullende grootten niet in EN 733 inbegrepen / Tamaños adicionales no includîdos en EN 733
5
H
[m]
4
3.5
4
3
5
Q[m /h]
10
2
20
3
4
30
5
l/s
40
50
100
10
20
200
30
40
300
400
50
500
100
700
KE1211.452/8
Etanorm / Etanorm-R
n = 1450 1/min
10
US.gpm
10
100
20
30
IM.gpm
40
20
50
30
100
40
200
50
100
300
200
400
300
500
400
1000
500
2000
1000
3000
2000
4000 5000
3000
4000 5000
300
125--500.2R 2) 4)
200--500R
150--500.1R
2) 4)
2) 4)
50
300--500R
2) 4)
250--500R
200
2) 4)
80--400 4)
100--400
40
125--400
2)
150--400
1) 2)
40--315 2) 4)
30
50--315 2) 4)
80--315 2)
65--315 2)
100--315
125--315
1) 2)
2) 4)
1) 2)
32--250.1
32--250
2) 4)
40--250
32--200.1 1) 2) 4)
32--200
10
50--250 1) 2)
1) 2)
80--250
1) 2)
50--200
65--200
1) 2)
1) 2)
1) 2)
1) 2)
40--160 1) 2)
50--160 1) 2)
80--200 1) 2)
125--200
5
1) 2)
50
40
100--200
200--260R
80--160
1) 2)
300--340R
30
2) 4)
2) 4)
250--300R
4)
65--160
2) 4)
150--250
150--200
1) 2)
300--360R
2) 4)
1) 4)
1) 2) 4)
32--160
250--330R
2) 4)
125--250
1) 2)
1) 2)
32--160.1
100
2) 4)
200--330R
100--250
1) 2)
40--200 1) 2)
1) 2)
65--250
2) 4)
250--400R
150--315
20
4)
300--400R
200--400R
200--250R
100--160
2) 4)
20
2) 4)
1) 2) 4)
32--125
32--125.1 1) 2) 3) 4)
4
40--125
50--125
65--125
10
3
2
1
0.8
2
5
H
[m]
2
3
4
1
5
3
Q[m /h]
2
10
20
3
4
5
30
l/s
40
10
50
100
20
30
200
40
300
50
400
100
500
4
ft
3
1000
200
300
2000
400 500
KE1211.454/9
Etanorm/Etanorm-R
Etanorm
n = 3500 1/min
30
40
50
30
100
US.gpm
40
50
100
200
IM.gpm
300
100
400
200
500
300
1000
400
2000
500
1000
3000
2000
300
32--200.1 1) 2) 4)
80--200 1) 2)
50--200 1) 2)
40--200 1) 2)
65--200
32--200 1) 2)
200
1) 2)
100--200 1) 2)
50
125--200
32--160.1 1) 2) 4)
1) 2) 4)
40--160
40
1) 2)
50--160 1) 2)
32--160
65--160
1) 2)
1) 2)
100--160
80--160
30
1) 2) 4)
1) 2)
100
32--125
1) 2) 3) 4)
32--125.1
40--125
50--125
20
65--125
50
H
[m]
40
10
30
6
6
3
10
2
Q[m /h]
3
4
20
30
5
40
l/s
50
100
10
20
200
30
40
300
400
50
ft
20
500
100
800
200
KE1211.4062/6
Etanorm / Etabloc / Etanorm-R
n = 1750 1/min
10
US.gpm
10
100
20
30
IM.gpm
20
40
30
50
40
100
50
200
100
300
200
400
300
500
400
1000
500
2000
1000
3000
2000
4000 5000
3000
10000
4000 5000
10000
300
125--400 2)
80--400 4)
100--400
200--400R
2) 4)
150--400
50
40--315
2) 4)
1) 2)
4)
40
80--315
65--315 2)
50--315 4)
100--315
2)
250--400R
125--315
2) 4)
150--315
1) 2)
1) 2)
1) 2)
30
32--250.1 4)
32--250
50--250
40--250
2) 4)
200
300--400R
80--250
65--250
1) 2)
1) 2)
20
1) 2)
1) 2)
100--250
250--330R
200--330R
125--250
1) 2)
2) 4)
100
300--360R
2) 4)
2) 4)
1) 2)
150--250
32--200.1 1) 2) 4)
40--200
32--200 1) 2)
50--200
1) 2)
65--200
80--200
1) 2)
1) 2)
1) 2)
1) 4)
125--200
100--200
1) 2)
2) 4)
2) 4)
32--160.1 1) 2) 4)
50
300--340R
200--260R
1) 2) 4)
40
150--200
10
40--160
32--160
50--160
1) 2)
1) 2)
1) 2)
4)
65--160
80--160
1) 2)
1) 2)
40--125
30
2) 4)
200--250R
100--160
2) 4)
1) 2) 4)
32--125
32--125.1 1) 2) 3) 4)
250--300R
20
50--125
5
65--125
4
10
3
2
H
[m]
1
2
3
4
1
5
l/s
3
Q[m /h]
2
10
20
3
4
5
30
40
10
50
100
20
30
200
40
300
50
400
100
500
5
ft
4
1000
200
300
2000
400
3000
500
KE1211.4064/10
3
Etanorm/Etanorm-R
Materials
Etanorm G /
Etanorm-RG
Volute casing
Discharge cover
Impeller
Spaltringe
1)
Grey cast iron JL 1040
Grey cast iron JL 1040 1)
Grey cast iron JL 10401)
1.4408
Grey cast iron GG
1.4408
Shaft
Shaft sleeve
Etanorm-R GC1
Etanorm M
1)
Tin bronze CC 480 K--GS 3)
Grey cast iron/Bleibronze GG/G-CuPb10Sn
Tempering steel C45
Chrome nickel molybdenum steel 1.4571
Shaft protection
sleeve
Bearing bracket
1.4122
Etanorm-RM
Tempering steel C45
Chrome nickel molybdenum
steel 1.4571
1.4122
Etanorm S
Volute casing
Discharge cover
Impeller
Spaltringe
Shaft
Shaft sleeve
Shaft protection sleeve
Bearing bracket
Etanorm-RS
Sphäroguss JS 1025 2)
Grey cast iron GG
Tepering steel C45
1.4122
Etanorm B
Tin bronze CC 480 K-GS 3)
Leaded bronze CC 495 K-GS 3)
Chrome nickel molybdenum steel
1.4462
1.4571
1.4571
Etanorm C
Cast chrome nickel molybdenum steel 1.4408
Benefits at a Glance
Large material selection
Grey cast iron, tin bronze, nodular cast iron, cast chrome nickel
molybdenum steel
Pressure jacket designed for 16
bar to guarantee high operating
reliability
Type: Etanorm-R
Connecting dimensions
and power ratings to
EN 733 (Etanorm)
Wear rings
service-friendly
Subject to technical modification without prior notice.
1) to EN 1561 = GJL-250
2) to EN 1563 = GJS-400-18-LT
3) to EN 1982
!
!
Impeller with optimized hydraulics, excellent efficiencies
and fine graduation of the QHperformance chart
Mechanical seal or gland
packing, uncooled
Robust deep-groove ball
bearings, protected against
contamination by v-rings
Back pull-out design: easy dismantling,
the casing may remain in the pipeline
when the pump is dismantled
Shaft sleeve/shaft protecting sleeve prevents
wear on the shaft
KSB Aktiengesellschaft
P.O. Box 1361, 91253 Pegnitz · Bahnhofplatz 1, 91257 Pegnitz (Germany)
Tel. +49 (92 41) 71 0 · Fax +49 (92 41) 71 17 91 · www.ksb.com
1211.1/14-10
01.06.2003
Suction geometry designed for max. suction capacity (NPSH) and optimal
cavitation behaviour
Type Series Booklet
1211.5/9-10 G2
50 and 60 Hz
Etanorm/Etanorm-R
Standardized Pumps
Fields of Application
Water supply
Fire-fighting systems
Sprinkling
Irrigation
Drainage
Heating
Air-conditioning systems
Drinking water
Service water
Hot water
Shaft Seal
Cooling water
Swimming pool water
Sea water
Fire-fighting water
Brackish water
Condensate
Brine
Oils
Cleaning agents
Fluid
Pure liquids not chemically or mechanically aggressive to the
pump materials.
Operating Data
Q
H
t
p2
Designation
EN(-R) 40 - 160 43 (6238) G 10 *)
Type series Etanorm
Pump size, e.g.
Actual impeller diameter - 100 mm, e.g. 143 mm
= (angular reduction of impeller vanes)
e.g. actual diameter 162/138 mm =
Casing material, e.g. JL 1040 2)
Shaft seal, e.g. mechanical seal Q1 Q1 X4GG
2) to EN 1561 = GJL-250
*) for Etanorm only
Accessories
Drive
Surface-cooled KSB-IEC three-phase squirrel cage motor
up to 1900 m3/h, (528 l/s)
up to 102 m
-30 °C to +140 °C
up to 16 bar 1)
Winding:
1) see pressure/temperature limits, page 5
Design
Horizontal volute casing pump, single-stage (pump size
125-200/2 two-stage), with power ratings and main dimensions
to EN 733 up to DN 200 / extension Etanorm-R, with bearing
bracket, in back pull-out design.
Shaft with replaceable shaft sleeve/shaft protecting sleeve in
the shaft seal area.
Volute casing and impeller with replaceable wear rings.
Volute casing with integrally cast pump feet.
Bearings
Deep-groove ball bearings, grease-lubricated.
DIN EN ISO 9001
Mechanical seal to EN 12756 (Stanard for Etanorm, for Etanorm-R as option) or gland packing.
up to 2.2 kW: 220-240 V/380-420 V
3 kW and above: 380-420 V/660-725 V
Design:
IMB 3
Enclosure:
IP 55
Thermal class: F with temperature sensors: 3 PTC
resistors
Operating mode: continuous operation S1
or
surface-cooled three-phase squirrel cage motor as described
above, but West European brand to KSB’s choice.
Coupling
Flexible coupling with/without spacer sleeve
Contact Guard
Coupling guard as per EN 294.
Baseplate
Sectional steel / folded steel plate, fabricated sectional steel
for the complete unit (pump and motor)
in torsion-resistant design
General Member of
Etanorm/Etanorm-R
Selection charts
Etanorm
n = 2900 1/min
20
30
40
20
120
50
30
US.gpm
40
50
100
200
IM.gpm
300
100
400
200
500
300
1000
400
2000
500
3000
1000
2000
100
300
32--250
4)
32--250.1
1) 2)
1) 2)
80--250
65--250
50--250
40--250
2) 3) 4)
100--250
1) 2)
1) 2)
1) 2)
200
50
65--200
32--200.1
40--200
1) 2) 4)
50--200
1) 2)
40
32--200
32--160.1
30
1) 2)
80--200
1) 2)
1) 2)
100--200
1) 2)
125--200
1) 2)
1) 2) 4)
1) 2) 4)
100
40--160
32--160
50--160
1) 2)
65--160
1) 2)
1) 2)
80--160
1) 2)
1) 2)
100--160
1) 2) 4)
20
32--125
32--125.1
1) 2) 3) 4)
40--125
50
50--125
65--125
40
10
30
ft
20
5
H
[m]
4
3.5
4
3
5
Q[m /h]
10
2
20
3
4
30
5
l/s
40
50
100
10
20
200
30
40
300
400
50
500
100
700
KE1211.452/8
Etanorm / Etanorm-R
n = 1450 1/min
10
US.gpm
10
100
20
30
IM.gpm
40
20
50
30
100
40
200
50
100
300
200
400
300
500
400
1000
500
2000
1000
3000
2000
4000 5000
3000
4000 5000
300
125--500.2R 2) 4)
200--500R
150--500.1R
2) 4)
2) 4)
50
300--500R
2) 4)
250--500R
200
2) 4)
80--400 4)
100--400
40
125--400
2)
150--400
1) 2)
40--315 2) 4)
30
50--315 2) 4)
80--315 2)
65--315 2)
100--315
125--315
1) 2)
2) 4)
1) 2)
32--250.1
32--250
2) 4)
40--250
32--200.1 1) 2) 4)
32--200
10
50--250 1) 2)
1) 2)
80--250
1) 2)
50--200
65--200
1) 2)
1) 2)
1) 2)
1) 2)
40--160 1) 2)
50--160 1) 2)
80--200 1) 2)
125--200
5
1) 2)
50
40
100--200
200--260R
80--160
1) 2)
300--340R
30
2) 4)
2) 4)
250--300R
4)
65--160
2) 4)
150--250
150--200
1) 2)
300--360R
2) 4)
1) 4)
1) 2) 4)
32--160
250--330R
2) 4)
125--250
1) 2)
1) 2)
32--160.1
100
2) 4)
200--330R
100--250
1) 2)
40--200 1) 2)
1) 2)
65--250
2) 4)
250--400R
150--315
20
4)
300--400R
200--400R
200--250R
100--160
2) 4)
20
2) 4)
1) 2) 4)
32--125
32--125.1 1) 2) 3) 4)
4
40--125
50--125
65--125
10
3
2
1
0.8
2
5
H
[m]
2
3
4
1
5
3
Q[m /h]
2
10
20
3
4
5
30
l/s
40
10
50
100
20
30
200
40
300
50
400
100
500
4
ft
3
1000
200
300
2000
400 500
KE1211.454/9
Etanorm/Etanorm-R
Etanorm
n = 3500 1/min
30
40
50
30
100
US.gpm
40
50
100
200
IM.gpm
300
100
400
200
500
300
1000
400
2000
500
1000
3000
2000
300
32--200.1 1) 2) 4)
80--200 1) 2)
50--200 1) 2)
40--200 1) 2)
65--200
32--200 1) 2)
200
1) 2)
100--200 1) 2)
50
125--200
32--160.1 1) 2) 4)
1) 2) 4)
40--160
40
1) 2)
50--160 1) 2)
32--160
65--160
1) 2)
1) 2)
100--160
80--160
30
1) 2) 4)
1) 2)
100
32--125
1) 2) 3) 4)
32--125.1
40--125
50--125
20
65--125
50
H
[m]
40
10
30
6
6
3
10
2
Q[m /h]
3
4
20
30
5
40
l/s
50
100
10
20
200
30
40
300
400
50
ft
20
500
100
800
200
KE1211.4062/6
Etanorm / Etabloc / Etanorm-R
n = 1750 1/min
10
US.gpm
10
100
20
30
IM.gpm
20
40
30
50
40
100
50
200
100
300
200
400
300
500
400
1000
500
2000
1000
3000
2000
4000 5000
3000
10000
4000 5000
10000
300
125--400 2)
80--400 4)
100--400
200--400R
2) 4)
150--400
50
40--315
2) 4)
1) 2)
4)
40
80--315
65--315 2)
50--315 4)
100--315
2)
250--400R
125--315
2) 4)
150--315
1) 2)
1) 2)
1) 2)
30
32--250.1 4)
32--250
50--250
40--250
2) 4)
200
300--400R
80--250
65--250
1) 2)
1) 2)
20
1) 2)
1) 2)
100--250
250--330R
200--330R
125--250
1) 2)
2) 4)
100
300--360R
2) 4)
2) 4)
1) 2)
150--250
32--200.1 1) 2) 4)
40--200
32--200 1) 2)
50--200
1) 2)
65--200
80--200
1) 2)
1) 2)
1) 2)
1) 4)
125--200
100--200
1) 2)
2) 4)
2) 4)
32--160.1 1) 2) 4)
50
300--340R
200--260R
1) 2) 4)
40
150--200
10
40--160
32--160
50--160
1) 2)
1) 2)
1) 2)
4)
65--160
80--160
1) 2)
1) 2)
40--125
30
2) 4)
200--250R
100--160
2) 4)
1) 2) 4)
32--125
32--125.1 1) 2) 3) 4)
250--300R
20
50--125
5
65--125
4
10
3
2
H
[m]
1
2
3
4
1
5
l/s
3
Q[m /h]
2
10
20
3
4
5
30
40
10
50
100
20
30
200
40
300
50
400
100
500
5
ft
4
1000
200
300
2000
400
3000
500
KE1211.4064/10
3
Etanorm/Etanorm-R
Materials
Etanorm G /
Etanorm-RG
Volute casing
Discharge cover
Impeller
Spaltringe
1)
Grey cast iron JL 10401)
1.4408
Grey cast iron GG
1.4408
Shaft
Shaft sleeve
Etanorm-R GC1
Etanorm M
1)
Grey cast iron/Bleibronze GG/G-CuPb10Sn
Tempering steel C45
Shaft protection
sleeve
Bearing bracket
1.4122
Etanorm-RM
Tempering steel C45
Chrome nickel molybdenum
steel 1.4571
1.4122
Etanorm S
Volute casing
Discharge cover
Impeller
Spaltringe
Shaft
Shaft sleeve
Shaft protection sleeve
Bearing bracket
Etanorm-RS
Grey cast iron GG
Tepering steel C45
1.4122
Etanorm B
Leaded bronze CC 495 K-GS 3)
1.4462
1.4571
1.4571
Etanorm C
1) to EN 1561 = GJL-250
2) to EN 1563 = GJS-400-18-LT
3) to EN 1982
Benefits at a Glance
Large material selection
Grey cast iron, tin bronze, nodular cast iron, cast chrome nickel
molybdenum steel
Pressure jacket designed for 16
bar to guarantee high operating
reliability
Type: Etanorm-R
Connecting dimensions
and power ratings to
EN 733 (Etanorm)
Wear rings
service-friendly
!
Suction geometry designed for max. suction capacity (NPSH) and optimal
cavitation behaviour
!
Impeller with optimized hydraulics, excellent efficiencies
and fine graduation of the QHperformance chart
Mechanical seal or gland
packing, uncooled
Robust deep-groove ball
bearings, protected against
contamination by v-rings
Back pull-out design: easy dismantling,
the casing may remain in the pipeline
when the pump is dismantled
Shaft sleeve/shaft protecting sleeve prevents
wear on the shaft
4
Etanorm/Etanorm-R
Pressure and Temperature Limits
Etanorm/
Etanorm R
Etanorm-R
Förderguttemperag
p
tur 1)4)
G
-30 C bis + 140
C
Prüfdruck
Enddruck p 2
2)
Etanorm
bis 21 bar
5)
3)
Etanorm-R
Pump size
bis 15 bar
M
-30 C bis + 140
C
bis 21 bar
bis 15 bar
S
-30 C bis + 140
C
bis 25 bar
bis 24 bar
B
-30 C bis + 140
C
10 bar
bis 13 bar
----
C
-30 C bis + 140
C
5)
bis 21 bar
----
1) For hot water heating systems to DIN 4752, section 4.5, application limits must
be observed.
2) The sum of inlet pressure and shut-off head must not exceed the values shown
in the diagram.
3) The casing components are checked for leakage by means of an internal pressure test to AN 1897/75-03 D00 with water.
4) For product temperatures > 140 C, Etanorm SYN shall be used.
5) See diagram
Pressure/Temperature Diagram for Flanges
to EN 1092-1 and EN 1092-2
Availability of pump sizes in the individual material variants
32-125.1
32-160.1
32-200.1
32-250.1
32-125
32-160
32-200
32-250
40-125
40-160
40-200
40-250
40-315
50-125
50-160
50-200
50-250
50-315
65-125
65-160
65-200
65-250
65-315
80-160
80-200
80-250
80-315
80-400
100-160
100-200
100-250
100-315
100-400
125-200
125-250
125-315
125-400
150-200
150-250
150-315
150-400
Etanorm
G
M
S
B
C
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
-X
X
X
X
-X
X
X
X
-X
X
X
X
-X
X
X
X
X
X
X
X
-X
X
X
X
-X
X
X
X
--X
X
X
X
X
-X
X
X
X
-X
X
X
--X
X
X
--X
X
X
-X
X
X
X
-X
X
X
X
-X
X
X
--X
X
X
-X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
G
GC1
M
S
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Pump size
Etanorm-R
all size
125-500/2
150-500.1
200-250
200-260
200-330
200-400
200-500
250-300
250-330
250-400
250-500
300-340
300-360
300-400
300-500
Etanorm-R
1) to EN 1561 = GJL-250
2) to EN 1563 = GJS-400-18-LT
3) only DN 65-150; DN 32-50 16 bar
5
Etanorm/Etanorm-R
Etanorm
B
6
9 10 11 12
X
X
X
X
X
X
BQ1EGG
3
C
QiQ1MMGG
1
Q1Q1X4GG
U3BEGG 4)
S
U3U3X4GG
M
RT-P
G
Pure graphite
Application limits
Zinnbronze/
Zinnbronze
Cast CrNiMo steel/
Cast CrNiMo steel
Grey cast iron/
Grey cast iron
Grey cast iron/
Tin bronze
Nodular cast iron/
Grey cast iron
Medium handled
Reference code
Mechanical seal
Gland Mechanipacking cal seal
Nb:p1 > 0,5 bar
Shaft seal
Gland
packing
Casing/Impeller
Na:p1 £ 0,5 bar
Materials 9)
Comments
Water
Brackish water 3)
Condensate 2)
Condensate, unconditioned
Cooling water 1)
(no anti-freezes)
X
B1
G1
C1
B10
G11
C11
Cast CrNiMo steel possible
G1
G10
open circuit: M1/M10 required
G1
G11
open circuit: M1/M11 required
X
X
B1
M1
B10
M10
If solids-laden: contact KSB
X
M1
M10
Contact KSB if VdS guideline
has been specified
Purity requirements cannot
be met.
t ! 25 °C;
p !10 bar
t !120 °C;
p !10 bar
t !120 °C;
p !10 bar
t ! 60 °C7);
p !10 bar
X
X
Cooling water pH value " 7.5
(with anti-freeze) 5)
t !120 °C;
p !10 bar
X
X
Dam water 1)
t ! 40 °C;
p ! 10 bar
t ! 60 °C7);
p !10 bar
X
X
X
Fire-fighting water 1)
t ! 60 °C7);
p ! 10 bar
X
X
Fully desalinated water
t !120 °C;
p !10 bar
as boiler feed water 2)
t !120 °C;
p !10 bar
Heating water 2)
t ! 120 °C;
p !10 bar
t ! 140 °C;
p !16 bar
t ! 110 °C;
p ! 10 bar
t ! 60 °C8);
p !10 bar
t ! 60 °C8);
p !10 bar
t ! 25 °C;
p ! 10 bar
t ! 60 °C7);
p ! 10 bar
X
X
X
X
X
X
Slightly contaminated water 1)
t "-30 °C;
t !110 °C
p !10 bar
X
X
Swimming-pool water
(fresh water) 1)
t ! 60 °C7);
p !10 bar
X
X
Swimming-pool water
(sea water) 3)
t ! 60 °C;
p ! 10 bar
X
X
Cooling brine, inorganic,
pH value > 7.5; inhibited
t "-30 °C;
t ! 25°C
p !10 bar
X
X
Water with anti-freeze,
pH value " 7.5; 1), 5)
t "-30°C;
t !110 °C
p !10 bar
X
X
Diesel oil, fuel oil EL
t ! 60 °C;
p !10 bar
Drilling/Grinding emulsion
t ! 60 °C;
p !10 bar
Lubricating oil, turbine oil, does
not apply to SDF oils (hardly
inflammable)
t ! 80 °C;
p !10 bar
Oil-water emulsion
Cleaning agents
t ! 60 °C;
p ! 10 bar
X
Lees for bottle rinsing
Brewery applications
t ! 90 °C;
p !10 bar
X
Beer mash
t ! 100 °C;
p ! 10 bar
X
X
G12
Beer wort
t ! 100 °C;
p ! 10 bar
X
X
G12
Drinking water 1)
Heating water 2)
Heating water 2)
Partly desalinated water 2)
Pure water 6)
Raw water 1)
Sea water 3)
X
X
X
X
X
X
X
X
C1
C11
X
X
X
G1
G11
X
X
X
X
X
G1
G3
G1
M1
G1
B1
G1
G11
G6
G10
M11
G11
B10
G10
G1
G11
X
G1
G10
Also if DIN 19 643 has been
specified
X
G1
G10
Cast CrNiMo steel possible if
t ≤ +25 °C
X
G1
G11
X
G1
G11
X
X
X
X
X
X
X
X
X
X
X
If used as circulation pump to
DIN 4752: p max. ! 10 bar
Cast CrNiMo steel possible
Coolants, cooling brines
Oils/Emulsions
X
X
X
S10
X
X
1) General criteria for results of water analysis: pH value " 7;
chloride (Cl) content !250 mg/kg. chlorine (Cl2) !0.6 mg/kg.
2) Treatment to VdTÜV 1466; additional requirement: O2 ! 0.02 mg/l
3) Criteria for all parts made of bronze:
ammonia (NH3) ! 5 mg/kg, free from hydrogen sulphide (H2S); no limitation of Cl content
required in this case.
Please contact KSB if limits are exceeded.
4) applies only to shaft units 25 and 35; shaft unit 55 = AQ1EGG
Pump size / shaft unit combinations see page 15
5) antifreeze on ethylene glycol basis with inhibitors. Content: >20 % to 50 %
(e.g. Antifrogen N)
6) No ultra-pure water! Conductivity at 25 °C: ! 800 mS/cm, neutral with regard to chemical
corrosion
7) Mechanical seal suitable for t ! 110 °C
8) Mechanical seal suitable for t ! 120 °C
9) Table of materials/pump size combinations see page 3.
G1
G9
X
S10
X
X
Grey cast iron possible, unless specific standards have
to be observed
G1
G9
G1
G7
If specified ”without” internal
primer, contact KSB. Grey
cast iron possible, unless
specific standards have to be
observed
Q1Q1EGG
If there is a risk of the pump running
g dryy due to excessive empp
tying of the tank,
tank an Etanorm with
dual seal in tandem arrangement
must be used.
Example:
Given: pure water 15 °C; Q = 60 m3/h; H = 80 m
Found:
Material variant (as per above table)
Pump size (as per characteristic curve 2900 1/min)
Reverence code (as per above table)
Required drive rating 22 kW
6
Etanorm G
50 - 250 G 1 (or G 11)
Etanorm/Etanorm-R
Etanorm-R
Shaft seal
Reference code
Gland packing
Medium handled
Materials
Casing/Impeller
Application limits
Gland
packing
Mechanical
seal
Na:
P1 ≤ 0,5 bar
Mechanical
seal
Nb:
P1 > 0,5 bar
G
M
S
1
4
Water
Condensate 2)
t ! 120 °C;
p !10 bar
X
X
Cooling water 1)
(no anti-freezes)
t ! 60 °C;
p !10 bar
X
X
Cooling water ph-Wert " 7,5
(with anti-freezes) 5)
t " -30 °C;
t ! 110 °C
p !10 bar
X
X
1)
t ! 60 °C;
p !10 bar
X
Drink water 1)
t ! 60 °C;
p !10 bar
X
Fire-fighting water 1)
t ! 60 °C;
p !10 bar
X
as boiler feed water 2)
Dam water
G1
Contact KSB
X
G1
G4
X
G1
G4
X
--
M4
X
M1
M4
X
--
M4
X
X
G1
G4
X
X
G1
G4
X
X
S1
S4
X
G1
G4
X
t ! 120 °C;
p !10 bar
X
2)
t ! 120 °C;
p !10 bar
X
Heating water 2)
t ! 140 °C;
p !16 bar
Heating water 2)
t ! 110 °C;
p !10 bar
X
X
Partly desalinated water 2)
t ! 120 °C;
p !10 bar
X
X
G1
Contact KSB
Pure water 4)
t ! 25 °C;
p !10 bar
X
X
X
G1
G4
Raw water
(industrie applications) 1)
t ! 60 °C;
p !10 bar
X
X
X
G1
G4
Raw water
irrigation) 1)
t ! 60 °C;
p !10 bar
X
X
--
G4
Service water
t ! 60 °C;
p !10 bar
X
X
--
G4
Slightly contaminated water 1)
t ! 60 °C;
p !10 bar
X
X
X
G1
G4
Swimming-pool water
(fresh water) 1)
t ! 60 °C;
p !10 bar
X
X
X
G1
G4
Cooling brine, inorganic,
pH value > 7.5; inhibited
t " -30 °C;
t ! 25 °C
p !10 bar
X
X
X
G1
G4
Water with anti-freeze,
pH value " 7.5; 1) 3)
t " -30 °C;
t ! 110 °C
p !10 bar
X
X
X
G1
G4
Diesel oil, fuel oil EL
t ! 60 °C;
p !10 bar
Drilling/Grinding emulsion
t ! 60 °C;
p !10 bar
Lubricating oil, turbine oil, does not
apply to SDF oils (hardly
t ! 80 °C;
inflammable)
p !10 bar
Oil-water emulsion
t ! 60 °C;
p !10 bar
X
X
t ! 90 °C;
p !10 bar
X
X
Beer mash
t ! 100 °C;
p ! 10 bar
X
X
Beer wort
t ! 100 °C;
p ! 10 bar
X
Heating water
X
Coolants, cooling brines
Oils/Emulsions
X
X
X
X
S4
X
G4
X
S4
X
G1
G4
Cleaning agents
Lees for bottle rinsing
G1
Brewery applications
1)
2)
3)
4)
5)
X
G4
X
G4
General criteria for results of water analysis: pH value " 7; chloride (Cl) content !250 mg/kg. chlorine (Cl2) !0.6 mg/kg.
Treatment to VdTÜV 1466; additional requirement: O2 ! 0.02 mg/l
antifreeze on ethylene glycol basis with inhibitors. Content: >20 % to 50 % (e.g. Antifrogen N)
No ultra-pure water! Conductivity at 25 °C: ! 800 mS/cm, neutral with regard to chemical corrosion
antifreeze on ethylene glycol basis with inhibitors. Content: >20 % to 50 % (e.g. Antifrogen N)
7

Catalogo General Bombas Centrifugas ETANORM KSB

Transcription

Similar documents

e-SV™ Series 1, 3, 5, 10, 15, 22, 33, 46, 66, 92, 125

Goulds Pumps

NPT, NPTF, G, Rc, Rp, Tr Taps

Movitec B

Glorex Perlmutt