FDM128 - Display for 8 LV Devices - User Guide

Transcription

FDM128
DOCA0037EN-01 04/2014
FDM128
Display for 8 LV Devices
User Guide
DOCA0037EN-01
04/2014
www.schneider-electric.com
The information provided in this documentation contains general descriptions and/or technical characteristics of the performance of the products contained herein. This documentation is not intended as a
substitute for and is not to be used for determining suitability or reliability of these products for specific user
applications. It is the duty of any such user or integrator to perform the appropriate and complete risk
analysis, evaluation and testing of the products with respect to the relevant specific application or use
thereof. Neither Schneider Electric nor any of its affiliates or subsidiaries shall be responsible or liable for
misuse of the information contained herein. If you have any suggestions for improvements or amendments
or have found errors in this publication, please notify us.
No part of this document may be reproduced in any form or by any means, electronic or mechanical,
including photocopying, without express written permission of Schneider Electric.
All pertinent state, regional, and local safety regulations must be observed when installing and using this
product. For reasons of safety and to help ensure compliance with documented system data, only the
manufacturer should perform repairs to components.
When devices are used for applications with technical safety requirements, the relevant instructions must
be followed.
Failure to use Schneider Electric software or approved software with our hardware products may result in
injury, harm, or improper operating results.
Failure to observe this information can result in injury or equipment damage.
© 2014 Schneider Electric. All rights reserved.
2
DOCA0037EN-01 04/2014
Table of Contents
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About the Book. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommendations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Certifications and Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Functional Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 2 Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Menu Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Browsing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 3 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 4 Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Real-Time Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device View for Circuit Breakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device View for Acti 9 Smartlink Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 5 Update and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Software Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Monitored LV Device Update. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Regular Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting Checklists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Protecting the Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendices
......................................................
Appendix A FDM128 Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Icon List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DOCA0037EN-01 04/2014
5
7
11
12
18
19
20
22
23
25
26
27
28
29
30
31
35
36
37
38
41
43
44
46
47
48
49
51
53
53
3
4
DOCA0037EN-01 04/2014
Safety Information
Important Information
NOTICE
Read these instructions carefully, and look at the equipment to become familiar with the device before
trying to install, operate, or maintain it. The following special messages may appear throughout this
documentation or on the equipment to warn of potential hazards or to call attention to information that
clarifies or simplifies a procedure.
PLEASE NOTE
Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel.
No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this
material.
A qualified person is one who has skills and knowledge related to the construction and operation of
electrical equipment and its installation, and has received safety training to recognize and avoid the
hazards involved.
FCC Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designated to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to correct
the interference at this own expense.
DOCA0037EN-01 04/2014
5
6
DOCA0037EN-01 04/2014
About the Book
At a Glance
Document Scope
This guide describes how to use the FDM128 display for 8 LV devices, installed in an Ethernet network, to
monitor and control:
 Circuit breakers equipped with communicating Micrologic trip units of the following ranges:
 Masterpact™ NW
 Masterpact™ NT
 Compact™ NS 1600b-3200
 Compact™ NS 630b-1600
 PowerPact™ P- and R-frame
 Compact™ NSX
 PowerPact™ H-, J- and L-frame

Devices connected to Acti 9 Smartlink:
 Acti 9 iOF+SD24 and OF+SD24 indication auxiliaries
 Acti 9 iACT24 and iATL24 auxiliaries for contactors and impulse relays in the Acti 9 range
 Acti 9 RCA iC60 remote control module with Ti24 interface
 Acti 9 Reflex iC60 integrated control circuit breaker with Ti24 interface
 EM2000T, iEM3110, iEM3155, iEM3210 and iEM3255 energy meters
 Compact NSX OF+SD indication auxiliaries
Validity Note
This documentation is valid for all FDM128 display for 8 LV devices.
The technical characteristics of the devices described in this document also appear online. To access this
information online:
Step
Action
1
Go to the Schneider Electric home page www.schneider-electric.com.
2
In the Search box type the reference of a product or the name of a product range.
 Do not include blank spaces in the model number/product range.
 To get information on grouping similar modules, use asterisks (*).
3
If you entered a reference, go to the Product Datasheets search results and click on the
reference that interests you.
If you entered the name of a product range, go to the Product Ranges search results and click
on the product range that interests you.
4
If more than one reference appears in the Products search results, click on the reference that
interests you.
5
Depending on the size of your screen, you may need to scroll down to see the data sheet.
6
To save or print a data sheet as a .pdf file, click Download XXX product datasheet.
The characteristics that are presented in this manual should be the same as those characteristics that
appear online. In line with our policy of constant improvement, we may revise content over time to improve
clarity and accuracy. If you see a difference between the manual and online information, use the online
information as your reference.
DOCA0037EN-01 04/2014
7
Related Documents
Title of Documentation
Reference Number
FDM128 Display for 8 LV Devices - Instruction Sheet
HRB45777
IFM Modbus-SL Interface for LV Circuit Breaker - Instruction Sheet
GHD16323AA
IFE Ethernet Interface for LV Circuit Breaker - Instruction sheet
HRB49218
IFE Ethernet Interface for LV Circuit Breaker - User Guide (IEC
Version)
DOCA0084EN
DOCA0084ES
DOCA0084FR
DOCA0084ZH
IFE Ethernet Interface for LV Circuit Breaker - User Guide (UL
Version)
1040IB1401 (EN)
1040IB1402 (ES)
1040IB1403 (FR)
1040IB1404 (ZH)
IO Input/Output Interface Module for LV Circuit Breaker - User Guide DOCA0055EN
(IEC Version)
DOCA0055ES
DOCA0055FR
DOCA0055ZH
IO Input/Output Interface Module for LV Circuit Breaker - User Guide 0613IB1317 (EN)
(UL Version)
0613IB1318 (ES)
0613IB1319 (FR)
0613IB1320 (ZH)
BCM ULP Breaker Communication Module - Installation Manual
5100512864A (EN, ES, FR)
Acti 9 Smartlink Modbus Communication System - User Manual
DOCA0004DE
DOCA0004EN
DOCA0004ES
DOCA0004FR
DOCA0004IT
DOCA0004PT
Acti 9 Smartlink Ethernet Communication System - User Manual
DOCA0073DE
DOCA0073EN
DOCA0073ES
DOCA0073FR
DOCA0073IT
DOCA0073PT
EGX300 PowerLogic™ Ethernet Gateway - User Guide
63230-319-216 (EN, ES, FR)
Micrologic 5/6 Trip Units for Compact NSX Circuit Breakers - User
Guide
LV434103 (FR)
LV434104 (EN)
LV434105 (ES)
Compact NSX Modbus Communication - User Guide
LV434106 (FR)
LV434107 (EN)
LV434108 (ES)
Micrologic 5 and 6 Trip Units for PowerPact H-, J-, and L- Frame
Circuit Breakers - User Guide
48940-312 (EN, ES, FR)
PowerPact H-, J-, and L- Frame Circuit Breakers Modbus
Communication - User Guide
48940-328 (EN, ES, FR)
Micrologic A/E Trip Units - User Guide
04443723A (FR)
04443724A (EN)
EAV16735 (ES)
Micrologic P Trip Units - User Guide
04443725A (FR)
04443726A (EN)
EAV16736 (ES)
Micrologic H Trip Units - User Guide
04443727A (FR)
04443728A (EN)
EAV16737 (ES)
Micrologic 2.0A, 3.0A, 5.0A, and 6.0A Trip Units - Instruction Bulletin 48049-136 (EN, ES, FR)
8
DOCA0037EN-01 04/2014
Title of Documentation
Reference Number
Micrologic 5.0P and 6.0P Trip Units - Instruction Bulletin
48049-137 (EN, ES, FR)
Micrologic 5.0H and 6.0H Trip Units - Instruction Bulletin
48049-330 (EN, ES, FR)
ULP System for Compact and Masterpact Circuit Breakers - User
Guide
TRV99100 (FR)
TRV99101 (EN)
TRV99102 (ES)
ULP System for PowerPact and Masterpact Circuit Breakers - User
Guide
48940-329 (EN, ES, FR)
You can download these technical publications and other technical information from our website at
www.schneider-electric.com.
DOCA0037EN-01 04/2014
9
10
DOCA0037EN-01 04/2014
FDM128
Introduction
DOCA0037EN-01 04/2014
Chapter 1
Introduction
Introduction
What Is in This Chapter?
This chapter contains the following topics:
Topic
DOCA0037EN-01 04/2014
Page
Overview
12
Recommendations
18
Certifications and Standards
19
General Specifications
20
Functional Specifications
22
Interface Specifications
23
11
Introduction
Overview
Presentation
The FDM128 display for 8 LV devices is a 1-to-8 human machine interface (HMI). The main component is
a 5.7 inch touch screen.
A FDM128 display unit can be connected to the devices via an Ethernet interface by using:
 An IFE gateway
 An Acti 9 Smartlink Ethernet
 A PowerLogic EGX300 Ethernet gateway
 Several IFE and Acti 9 Smartlink Ethernet
Each type of connection is described further in this section.
The FDM128 display unit can be set up in one or any combination of these architectures. When combining
these architectures, make sure that there is no more than one master/slave configuration.
The FDM128 display unit can monitor and control up to eight LV devices. The information displayed
includes measurements, alarms, and operating assistance data.
For ease of installation, an autodiscovery function is embedded in the FDM128 display unit.
Number and Nature of Monitored Devices
The maximum number of devices that can be monitored simultaneously is eight devices, among the list
below:
 Circuit breakers:
 Masterpact NT/NW
 Compact NS
 Compact NSX
 PowerPact P- and R-frame
 PowerPact H-, J-, and L-frame

12
Acti 9 Smartlink:
 Acti 9 Smartlink Modbus
 Acti 9 Smartlink Ethernet
DOCA0037EN-01 04/2014
Introduction
FDM128 Display Unit Connected to an IFE Gateway
The following diagram shows an IFE-based network architecture that includes an Acti 9 Smartlink Modbus:
A
B
C
D
E
F
G
H
I
J
K
L
DOCA0037EN-01 04/2014
FDM128 display for 8 LV devices
IFE Ethernet interface for LV circuit breaker and gateway
IFM Modbus-SL interface for LV circuit breaker
FDM121 display for LV circuit breaker
IO input/output interface module for LV circuit breaker
Masterpact NT/NW circuit breaker
Compact NSX, PowerPact H-, J-, or L-frame circuit breaker
Acti 9 Smartlink Modbus
ULP line terminator
ULP cable
Breaker ULP cord
NSX cord
Ethernet
Modbus-SL
24 Vdc
13
Introduction
FDM128 Display Unit Connected to an Acti 9 Smartlink Ethernet Gateway
The following diagram is an example of an Acti 9 Smartlink Ethernet network architecture, in a floor
switchboard application:
A
B
C
D
E
F
14
Switch Connexium
Acti 9 Smartlink Ethernet
iEM• Acti 9 Smartlink energy meter
Ethernet
Modbus-SL
24 Vdc
DOCA0037EN-01 04/2014
Introduction
FDM128 Display Unit Connected to a PowerLogic EGX300 Ethernet Gateway
The following diagram is an example of a network architecture with a PowerLogic EGX300 Ethernet
gateway:
A
B
C
D
E
F
G
H
I
J
K
L
M
DOCA0037EN-01 04/2014
Switch Connexium
EGX300 Ethernet gateway
CCM Modbus cradle communication module
ULP line terminator
ULP cable
Breaker ULP cord
NSX cord
Ethernet
Modbus-SL
24 Vdc
15
Introduction
FDM128 Connected to Several IFE or Acti 9 Smartlink Ethernet
The following diagram shows an IFE- and Acti 9 Smartlink-based network architecture:
A
B
C
D
E
F
G
H
I
J
16
Switch Connexium
IFE Ethernet interface for LV circuit breaker
IO input/output interface module for LV circuit breaker
ULP cable
Breaker ULP cord
NSX cord
Ethernet
24 Vdc
DOCA0037EN-01 04/2014
Introduction
Component Part Numbers
The table below lists the part numbers for the components listed in the architecture diagrams:
Component
Description
Part Number
–
LV434128
STU 5in7 front module spare part
–
HMIS85
IFE Ethernet interface for LV circuit breaker
Ethernet interface
LV434010
Ethernet interface and gateway
LV434011
–
 TRV00210 (IEC)
 STRV00210 (UL)
–
 TRV00121 (IEC)
 STRV00121 (UL)
IO input/output interface for LV circuit breaker
–
LV434063
ULP line terminator
10 ULP line terminators
TRV00880
ULP cable
Breaker ULP cord
NSX cord
L = 0.3 m (0.98 ft), 10 cables
TRV00803
L = 0.6 m (1.97 ft), 10 cables
TRV00806
L = 1 m (3.28 ft), 5 cables
TRV00810
L = 2 m (6.56 ft), 5 cables
TRV00820
L = 3 m (9.84 ft), 5 cables
TRV00830
L = 5 m (16.40 ft), 1 cable
TRV00850
L = 0.35 m (1.15 ft)
LV434195
L = 1.3 m (4.26 ft)
LV434196
L = 3 m (9.84 ft)
LV434197
L = 0.35 m (1.15 ft)
LV434200
L = 1.3 m (4.27 ft)
LV434201
L = 3 m (9.84 ft)
LV434202
–
A9XMEA08
–
A9XMSB11
PowerLogic EGX300 Ethernet gateway
–
 EGX300 (Schneider
Electric)
 EGX300SD (Square D)
DOCA0037EN-01 04/2014
iEM2000T energy meter
–
A9MEM2000T
iEM3110 energy meter
–
A9MEM3110
–
A9MEM3155
–
A9MEM3210
–
A9MEM3255
17
Introduction
Recommendations
Critical Systems, Alarms, and Handling Requirements
Critical alarm indicators and system functions require independent and redundant hardware protection
and/or mechanical interlocks.
If the FDM128 display for 8 LV devices, for any reason, becomes inoperative (for example, an inoperative
backlight) it may be difficult or impossible to identify a function. Functions that may present a hazard if not
immediately executed, such as an emergency stop, must be provided independently of the FDM128
display unit.
The design of the control system must take into account simultaneously:
 An inoperative FDM128 display unit.
 The operator inability to control the circuit breakers or to respond to detected errors by using the
FDM128 display unit.
Handling the LCD Panel
The following characteristics are specific to the LCD panel and are considered normal behavior:
 LCD screen may show unevenness in the brightness of certain images. These images may appear
differently when seen from outside the specified viewing angle. Extended shadows, or cross-talk, may
also appear on the sides of screen images.
 LCD screen pixels may contain black and white-colored spots and color display may seem to have
changed over time.
 When the same image is displayed for a long period, an after-image may appear when the image
changes. If this happens, turn off the FDM128 display unit, wait 10 seconds, and then restart it.
NOTE: Do not display the same image for a long time, change the screen image periodically.
CAUTION
SERIOUS EYE AND SKIN INJURY
The liquid present in the LCD panel contains an irritant:
 Avoid direct skin contact with the liquid.
 Wear gloves when you handle a broken or leaking FDM128 display unit.
 Do not use sharp objects or tools in the vicinity of the LCD touch panel.
 Handle the LCD panel carefully to prevent puncture, bursting, or cracking of the panel material.
If the panel is damaged and any liquid comes in contact with your skin, immediately rinse the area with
running water for at least 15 minutes.
If the liquid gets in your eyes, immediately rinse your eyes with running water for at least 15 minutes and
consult a doctor.
Failure to follow these instructions can result in injury or equipment damage.
Using Touch Panel Correctly
WARNING
UNINTENDED EQUIPMENT OPERATION


Operate the touch panel with only one finger.
Do not activate two or more points of the touch panel simultaneously.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
Use only one finger to select an object on the touch panel.
If the touch panel receives pressure at two or more points at the same time, an unintended object could be
selected.
18
DOCA0037EN-01 04/2014
Introduction
Certifications and Standards
Introduction
Schneider Electric submitted this product for independent testing and qualification by third-party listing
agencies. These agencies have certified this product as meeting the following standards.
The FDM128 display unit is certified by the Underwriters Laboratories according to UL 508 for Industrial
Control Equipment.
The FDM128 display unit is designed to comply to merchant navy bridge and deck requirements (refer to
the Schneider Electric website for installation guidelines).
For detailed information, contact your local distributor or see the catalog and marking on the product.
Compliance with Standards
The FDM128 display unit complies with the following standards:
 IEC 60947-1 general rules
 UL 508, Industrial Control Equipment
 CSA C22.2 No. 14-05 Industrial Control Equipment
 IACS E10
Hazardous Substances
The FDM128 display unit is designed for compliance with the following directives and standards:
 WEEE, Directive 2002/96/EC
 RoHS, Directive 2002/95/EC
 RoHS China, Standard SJ/T 11363-2006
UL Conditions of Acceptability for the FDM128 display unit
The FDM128 display unit is suitable for use in hazardous locations in accordance with Class 1, Division 2
standards. All relevant local, state, and regional codes must be followed.
CE Markings
This product conforms to the requirements for applying the
label.
WARNING
RISK OF EXPLOSION IN HAZARDOUS LOCATIONS






Verify that the power, input, and output (I/O) wiring are in accordance with Class I, Division 2 wiring
methods.
Do not substitute components that could impair compliance to Class I, Division 2.
Do not connect or disconnect equipment unless power has been switched off or the area is known to
be non-hazardous.
Securely lock externally connected units and each interface before turning on the power supply.
Do not disconnect while the circuit is live.
Front panel is a potential electrostatic charging hazard. Wipe the front panel of the terminal with a
damp cloth before turning on.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
DOCA0037EN-01 04/2014
19
Introduction
General Specifications
Electrical Characteristics
Characteristic
Value
Rated input voltage
24 Vdc
Input voltage limits
20.4–28.8 Vdc
Acceptable voltage drop
≤ 7 ms
Power consumption
≤ 6.8 W
In-rush current
≤ 30 A
Voltage endurance between power terminal and
functional ground (FG)
1,000 Vac 20 mA for 1 minute
Insulation resistance between power terminal and
functional ground (FG)
10 MΩ or higher at 500 Vdc
Physical Characteristics
Characteristic
Value
Ambient operating temperature (cabinet interior and
panel face)
–10 ° C to +55 ° C (14–131 ° F)
Storage temperature
–40 ° C to +85 ° C (–40 ° F to +185 ° F)
Relative humidity
95 % without condensation (non-condensing, wet bulb
temperature 55 ° C (131 ° F) or less)
Air purity (dust)
≤0.1 mg/m3 (≤10-7 oz/ft3) (non-conductive levels)
Corrosive gases
Free of corrosive gases
Atmospheric pressure
800–1,114 hPa (2000 m (6,500 ft) or lower)
Mechanical Characteristics
20
Characteristic
Value
Vibration immunity (operating)
IEC 60068-2-6
1 gn (1 g) 5–150 Hz (maximum 3.5 mm (0.13 in.))
Protection (front panel)
IP65 (IEC 60529)
Protection structure
Type 4X indoor, installed on a panel
Protection (rear panel)
IP20 (IEC 60529)
Shock immunity (operating)
IK05 (IEC 60068-2-75)
15 gn (1 g) 11 ms
Cooling method
Natural air circulation
Weight
0.25 kg (0.55 lb.)
Color
Front bezel: dark gray
Material
PC/PBT and PAA
DOCA0037EN-01 04/2014
Introduction
Electrical Environment Specifications
Characteristic
Value
Noise immunity
Noise voltage: 1,000 Vp-p
Pulse width: 1 µs
Rising time: 1 ns
High energy surges
2 kV CM, 0.5 kV DM on DC power supply
2 kV CM on shielded cables
Electrical fast transient burst
2 kV CM, 2 kV DM on DC power supply
1 kV on shielded cables
Radiated radio frequency electromagnetic field
10 V/m / 80 MHz to 2 GHz
Sinus amplitude modulated 80 %
1 kHz + internal clock frequency
Electrostatic discharge immunity
8.8 kV direct contact
12 kV air contact
Power frequency magnetic field
100 A/m continuous
Grounding
D-type grounding (SG-FG connected)
CM: Common Mode
DM: Differential Mode
DOCA0037EN-01 04/2014
21
Introduction
Functional Specifications
Display Characteristics
Characteristic
Description
Type
Color TFT LCD
Resolution (pixels)
320 x 240 (QVGA)
Active display area (W x H)
115.2 x 86.4 mm (4.53 x 3.40 in.)
Display colors
65,536 colors
Backlight
LED backlight
Lifetime: 50,000 hours before dimmed to 50 % brightness
Ambient temperature: 25 ° C (77 ° F)
Non-exchangeable
Brightness adjustment
16 levels of adjustment available via touch panel in the General settings menu.
Brightness on LCD surface
White LED: 350 cd/m2 (33 cd/ft2) maximum
View angle
 80 degrees: left, right
 70 degrees: up
 70 degrees: down
(Test condition: contrast ratio > 2)
Clock
Variations in operating conditions can cause a clock shift from -380 seconds to +90 seconds per month.
Touch Panel
22
Characteristic
Description
Type
Analog resistance film type (metal tab, golden plated)
Lifetime
1 million touches or more
DOCA0037EN-01 04/2014
Introduction
Interface Specifications
USB1 Interface (USB Peripherals)
HOST Interface Characteristic
Transmission speed
Value
High speed
480 Mbps
Full speed
12 Mbps
Low speed
1.5 Mbps
Maximum current supplied
250 mA
Maximum transmission distance
5 m (16.40 ft) at 12 Mbps
Connector
USB Type-A V2.0
Ethernet Interface
LED
DOCA0037EN-01 04/2014
Description
Green 1
Link state
Green 2
Activity
23
Introduction
24
DOCA0037EN-01 04/2014
FDM128
Presentation
DOCA0037EN-01 04/2014
Chapter 2
Presentation
Presentation
Topic
DOCA0037EN-01 04/2014
Page
Screen
26
Menu Structure
27
Browsing
28
25
Presentation
Screen
Overview
The following figure describes the display area:
A
B
C
D
E
F
Header
Title bar
Headpiece
Right area
Left area
Footer
Header
The header (A) is composed of the following elements:
 Current date and time
 4 direct-access icons to the main functions (General view, Editing devices, Communication
settings, and General settings)
Title Bar
The title bar (B) contains the title of the screen or name of the selected device.
Main Area
The main area includes the headpiece (C), the right area (D), and the left area (E).
The following table describes the parts of the main display area:
Position
Description
Use
Headpiece (C)
Right area title
Navigate through the submenus items.
Right area (D)
Information
Displays information of the selected submenu or submenu item.
Information screens depend on the device.
Left area (E)
Submenus, if applicable
Navigate through the submenus.
Various contents depending on the device.
Footer
The footer (F) contains some navigation icons depending on the selected screen.
For more information, refer to the icon list (see page 53).
If there is more than one page in the selected submenu, the screen number is displayed. The screen
number format is X/Y, with X that is the current screen number and Y is the total screen number.
26
DOCA0037EN-01 04/2014
Presentation
Menu Structure
Menu Types
FDM128 menus are divided into two types:
 Settings menus: blue title bar background
 Operation menus: green title bar background
Settings Menus
Settings menus are composed of two sequences:
 General settings sequence
 Devices settings sequence: communication settings, autodiscovery, and editing devices
The setting wizard (see page 31) of the FDM128 display unit guides you through these sequences.
General View
The General view menu is used to monitor up to 8 devices at the same time.
For further information, refer to the general view topic (see page 36).
Device View
Device view menus are only accessible from the General view menu.
The Device view menu is composed of the following submenus:
 Quick view (see page 38)
 Measures (see page 38)
 Alarm history (see page 39)
 Control (see page 39)
 Maintenance (see page 40)
 I/O1 and I/O2 (see page 40)
DOCA0037EN-01 04/2014
27
Presentation
Browsing
Navigate Through the Screens
In a menu or a submenu, you can navigate through the screens by using the footer icons.
The browsing actions are executable by pressing the icons. Refer to the icon list (see page 53) to get the
meaning of each of them.
The icons are available depending on the network configuration, the selected menu, and the possible
actions.
NOTE: A gray icon means that the option or action is not available in the actual context.
Data Entry
When an action requires an alphanumeric entry (for example, typing a designation), the following touch
keyboard is displayed:
When an action requires a numeric entry (for example, typing an IP address), the numeric keyboard is
displayed.
NOTE: You can also display the numeric keyboard by pressing the 123 key on the alphanumeric keyboard.
28
DOCA0037EN-01 04/2014
FDM128
Configuration
DOCA0037EN-01 04/2014
Chapter 3
Configuration
Configuration
Topic
DOCA0037EN-01 04/2014
Page
Prerequisites
30
Setting Wizard
31
29
Configuration
Prerequisites
Ethernet Network
The Ethernet connections of the IP gateways (EGX300, IFE, Acti 9 Smartlink Ethernet) in the Ethernet
network must be correctly installed and configured. The Ethernet devices must be in the same subnet. For
further information, refer to the corresponding user guides.
Modbus Serial Line Network
The devices in the Modbus serial line network must be correctly installed and configured with the following
Modbus parameters:
Parameter
Value
Modbus address (slaves only)
The Modbus address of each monitored device must be unique. The range of
Modbus addresses is 1–30.
Physical interface
RS-485 2-wire
Transmission mode
RTU (Automatic)
Communication speed
The communication speed must be the same for all devices.
Parity
The parity must be the same for all devices.
Response time-out
1 second
To check the Modbus parameters of each monitored device, refer to:
 The BCM ULP Breaker Communication Module Installation Manual
 The IFM Modbus-SL Interface for LV Breaker - Instruction Sheet
 The Acti 9 Smartlink Modbus Communication System User Manual
30
DOCA0037EN-01 04/2014
Configuration
Setting Wizard
Wizard Presentation
A setting wizard is automatically launched at first power-on to help you setup the FDM128 display unit.
The setting wizard guides you through three main configuration parts:
1. The FDM128 display unit general settings
2. The communication settings depending on the network architecture: IFE- or Acti 9 Smartlink Ethernetbased architecture, EGX-based architecture, or several IFE or Acti 9 Smartlink Ethernet architecture
3. The editing devices function
Each configuration part is described further in this section.
In addition, you have direct access to the Communication settings screen, the Editing devices screen,
and the General settings menu with the three upper right icons. Refer to the icon list in appendices for a
description of each icon.
Each time you modify the communication network, it is recommended to update the communication
settings.
General Settings
The following table describes the steps you go through with the setting wizard to configure the FDM128
display unit general settings:
Step
Screen
Action
1
Welcome
Touch the screen to start the wizard.
2
Language selection
Press the desired language.
In the footer, press the down arrow icon to access the next step.
3
Date
Press the up/down arrows icons to set the current year, month, and day.
4
Time
Press the up/down arrows icons to set the current hour and minute.
5
Phase ID
Press one of the two possible ways to represent the phases 1,2,3,N, or
A,B,C,N.
6
Units of measurement
Select the units of measurement for the analog input of the IO modules:
 The unit of temperature (° C or ° F)
 The unit of volume (m3 or gallon US or gallon UK)
7
Brightness
Press the -/+ icons to adjust the brightness level of the display.
In the footer, press Finish.
The setting wizard displays the Selection of the communication
architecture screen to allow you to set up the FDM128 communication.
Follow the communication settings procedure that corresponds to your
network architecture.
Communication Settings for IFE Gateway- or Acti 9 Smartlink Ethernet Gateway-based Architecture
This procedure is applicable when:
The FDM128 display unit is connected to an IFE gateway (see page 13).
 The FDM128 display unit is connected to an Acti 9 Smartlink Ethernet gateway (see page 14).

The FDM128 setting wizard guides you through the following steps:
Step
DOCA0037EN-01 04/2014
Action
1
In the Selection of the communication architecture screen, select IFE-based architecture or Acti 9
Smartlink IP-based architecture.
2
Configure the FDM128 display unit within the network.
Set the following parameters:
 The FDM128 IP address
 The subnet mask
 The subnet default gateway
31
Configuration
Step
Action
3
Press YES to indicate that the FDM128 display unit is connected to an IFE gateway or Acti 9 Smartlink
Ethernet gateway.
4
Set the IP address of the IFE gateway or Acti 9 Smartlink Ethernet gateway.
5
Press Start to launch the autodiscovery sequence.
Up to 16 devices are displayed.
6
Select up to eight devices among the devices displayed.
7
If you selected fewer than 8 devices among the devices displayed, you can configure manually extra IFE
or Acti 9 Smartlink Ethernet devices.
8
Press Finish.
The FDM128 display unit can now monitor the list of selected devices.
The setting wizard displays the Editing devices screen to allow you to edit the label and name of the
devices.
The setup of Acti 9 Smartlink devices is not included in the wizard. To set up an Acti 9 Smartlink device,
open its Device view (see page 41) and press the Setup button.
Communication Settings for EGX Gateway-based Architecture
This procedure is applicable when the FDM128 display unit is connected to a PowerLogic EGX300
gateway (see page 16).
Step
Action
1
In the Selection of the communication architecture screen, select EGX300-based architecture.
2
Configure the FDM128 display unit with the EGX300 gateway Ethernet parameters.
 The EGX300 gateway IP address
 The subnet mask
3
Press Start to launch the autodiscovery sequence.
Up to 16 devices are displayed.
4
Select up to eight devices among the discovered devices.
5
Press Finish.
devices.
32
DOCA0037EN-01 04/2014
Configuration
Communication Settings for Several IFE or Acti 9 Smartlink Ethernet Architecture
The procedure corresponds to the FDM128 display unit connected to several IFE or Acti 9 Smartlink
Ethernet (see page 16).
Step
Action
1
In the Selection of the communication architecture screen, select IFE-based architecture or Acti 9
Smartlink IP-based architecture.
2
Configure the FDM128 display unit within the network.
 The subnet mask
3
Press NO to indicate that there is no gateway.
4
Configure manually up to 8 IFE or Acti 9 Smartlink Ethernet devices.
5
Press Finish.
devices.
Autodiscovery
The autodiscovery sequence detects up to 16 devices on the network. These devices are displayed sorted
in ascending address order, with the address indicated in the first column.
NOTE: The 16 detected devices are those with the 16 first addresses.
Among the detected devices, you can select a maximum of eight devices.
The FDM128 display unit guides you through the following autodiscovery procedure:
Step
Action
1
The autodiscovery sequence is started during the communication settings procedure.
A progress bar is displayed during the autodiscovery sequence. The sequence duration is around
5 minutes.
2
In the list of the discovered devices:
 Press the crossed check box to deselect unwanted devices.
 Press the empty check box to select wanted devices.
3
Press Finish.
The Editing devices screen appears.
NOTE: By default, the eight devices with the 8 first addresses are selected.
DOCA0037EN-01 04/2014
33
Configuration
Manual Configuration
You configure manually devices either after an autodiscovery sequence, or if you do not have a IFE or
Acti 9 Smartlink gateway.
To configure devices manually during the device settings sequence, proceed as follows:
Step
Action
1
On the configuration screen, tick the check boxes of the number of IFE or Acti 9 Smartlink devices to
configure.
2
For each selected device, set its IP address.
3
Press OK.
Editing Devices
When the communication network is configured, you can use the FDM128 display unit to:
 Provide a label to each device. The label is defined in ID field and is only displayed in the FDM128
display unit.
 Rename a device. The name is defined in Name field and is the actual name of the device. Renaming
a device may require to use the password of the device.
The ID field contains up to 4 characters.
The Name field contains up to 12 characters.
NOTE: Press OK to validate the communication settings and reach the operation mode.
Power Loss
In case of power loss, the FDM128 display unit retains the settings.
At power recovery, the FDM128 display unit displays a screen to set date and time. The rest of the
configuration remains set.
General Settings During Operation
During operation, you can access the General settings menu by pressing
34
.
DOCA0037EN-01 04/2014
FDM128
Operation
DOCA0037EN-01 04/2014
Chapter 4
Operation
Operation
Topic
DOCA0037EN-01 04/2014
Page
General View
36
Real-Time Alarms
37
Device View for Circuit Breakers
38
Device View for Acti 9 Smartlink Devices
41
35
Operation
General View
Overview
The General view menu allows you to monitor up to 8 selected devices through summarized information.
There are two display modes:
 Icon
 List
You can switch between the two modes by pressing the corresponding icon in the lower right corner of the
screen.
From this menu, you can reach the Device view screens of the monitored devices:
 Device view for circuit breakers, dedicated to Compact, PowerPact, Masterpact circuit breakers
(see page 38).
 Device view for Acti 9 Smartlink devices (see page 41).
Icon Mode
In the icon mode, the eight devices are displayed on one screen, each one by an icon.
To reach a Device view, press the corresponding icon.
List Mode
In the list mode, four devices are displayed per screen, one per line.
To reach Device view, press the
36
icon on the corresponding line.
DOCA0037EN-01 04/2014
Operation
Real-Time Alarms
Overview
Alarms are displayed differently according to their priority level.
NOTE: The alarms must be acknowledged on the circuit breakers. There is no acknowledgement from the
FDM128.
Alarms for Circuit Breakers
The circuit breaker pre-defined alarms are displayed on the FDM128 display unit as follows:
Alarm Priority
Description
High
When a high-priority alarm occurs, the FDM128 screen shows a pop-up window. The
following window represents an example of an alarm on circuit breaker CB01.
You must close this window before returning to the General view.
This alarm also appears as a red icon on the General view screen and on the title bar of
the Device view screen.
Medium
When a medium-priority alarm occurs, an orange icon appears on the General view
screens and on the title bar of the Device view screens.
Low
Low-priority alarms are only registered in the alarm history and viewable in the Alarm
history submenu.
NOTE: The circuit breaker alarms configured with the customer engineering tool are only registered in the
alarm history and viewable in the Alarm history submenu. For information about a customer engineering
tool, refer to the circuit breaker documentation.
Alarms for Circuit Breakers Connected to Acti 9 Smartlink Devices
Alarms are raised depending on the type of circuit breaker:
 Acti 9 circuit breakers: when an alarm occurs, the FDM128 screen shows a pop-up window. You must
close this window before returning to the General view. This alarm also appears as a red icon on the
General view screen and in the corresponding Acti 9 Smartlink Device view (Status).
 Other circuit breakers: an alarm appears as a red icon on the General view screen and in the
corresponding Device view (Status).
An example of this type of circuit breaker is the item C in the schema FDM128 display unit connected
to an Acti 9 Smartlink Ethernet (see page 14).
DOCA0037EN-01 04/2014
37
Operation
Device View for Circuit Breakers
Overview
For each submenu selected in the left tab of the main area, a headpiece allows you to navigate through
the tabs. Press the corresponding tab title to display it.
Data displayed in the Device view screen depends on the circuit breaker and the type of Micrologic trip
unit installed. Refer to the relevant Micrologic user guides.
Measure Display Modes
The measures can be displayed in three modes:
 Numeric mode
 Bargraph mode
 Dial mode
You can switch between the three modes by pressing the corresponding icon in the lower right corner of
the screen.
Numeric Mode
Bargraph Mode
Dial Mode
Quick View
The Quick view submenu displays the status and main measures of a single circuit breaker.
There is no tab in this submenu.
Measures
The Measures submenu displays the measures of a single circuit breaker.
NOTE: You can reset the minimum and maximum values by pressing the R icon.
The tabs are the following:
I
 V
 PQS
 E
 F-PF-Cosϕ
 THD

38
DOCA0037EN-01 04/2014
Operation
Alarm History
The Alarm history submenu gives access to the various histories of the circuit breaker.
The table presents the description and number of records of each history according to the circuit breaker.
Tab
Description
Compact NSX and
PowerPact H-, J-, and
L-Frame Circuit
Breakers Number of
Records
Masterpact NT/NW,
Compact NS and PowerPact
P- and R-Frame Circuit
Breakers Number of Records
Trip
Trip history
17
10
Alarm
Alarm history
10
–
Mainten.
Operation history
10
–
BSCM
BSCM event history
10
–
Each record is summarized on three lines:
 Code
 Date and time of event occurrence and completion
 Designation
Control
DANGER
HAZARD OF ELECTRIC SHOCK


Check that the downstream electrical equipment is safe.
Check that you control the appropriate circuit breaker.
Failure to follow these instructions will result in death or serious injury.
CAUTION
HAZARD OF CLOSING ON ELECTRICAL FAULT
Do not close the circuit breaker again without first inspecting and, if necessary, repairing the downstream
electrical equipment.
Before controlling a circuit breaker, you have to:
 Ensure that Masterpact NT/NW, Compact NS, or PowerPact P-frame circuit breakers are equipped with
a BCM ULP and communicating coils MX and XF or a communicating motor mechanism.
 Ensure that Compact NSX or PowerPact H-, J-, and L-frame circuit breakers are equipped with a BSCM
and a communicating motor mechanism in automatic mode.
 Ensure that the circuit breaker is in remote control mode.
 Ensure that you know the circuit breaker password. The password is set with the customer engineering
tool of the circuit breaker.
 When the circuit breaker is connected to an IFE or IFM, ensure that the IFE or IFM locking pad points
to the unlocked position.
The Control submenu allows you to check the status and to execute actions remotely to actuate the circuit
breaker.
The table presents the possible actions depending on the circuit breaker:
DOCA0037EN-01 04/2014
Action
Circuit breaker
Open
All circuit breakers
Close
All circuit breakers
Reset
Compact NSX and PowerPact H-, J-, and L-frame circuit breakers only
39
Operation
The FDM128 display unit takes you through the following sequence:
Step
Action
1
In the submenu Control, press the action for the target circuit breaker.
A password popup is displayed.
2
Enter the circuit breaker password.
A confirmation popup is displayed.
3
Press YES.
The following operations occur:
1. The command is sent to the circuit breaker.
2. The circuit breaker executes the command.
3. When the execution of the command is finished, a result popup is displayed with a failure or success
message.
4
Press OK to close the result popup.
Maintenance
The table presents the use of each tab of the Maintenance submenu:
Tab
Use
Information
Displays the contact wear rate, load profile, and the circuit breaker counter values.
Product ID
Displays the identification data of all ULP modules of the intelligent modular unit.
Reset
Resets the maximum values, minimum values, and energy counters of all ULP modules of the
intelligent modular unit.
I/O1 and I/O2
For each connected IO module, the I/O1 and I/O2 submenus allow you to:
 Check the status of its inputs.
 Control its outputs.
 Read its pulse counters.
Before controlling an IO module output, you have to:
Ensure that the output is assigned with the customer engineering tool of the circuit breaker.
 Ensure that you know the IO module password. The password is set with the customer engineering tool
of the circuit breaker.
 When the IO module is connected to an IFE or IFM, ensure that the IFE or IFM locking pad points to the
unlocked position.

The Control submenu allows you to check the status and to execute actions remotely to actuate the IO
module output.
The possible actions are to open or close the output.
The FDM128 display unit takes you through the following sequence:
Step
40
Action
1
In the submenu Control, press the action for the target output.
A password popup is displayed.
2
Enter the IO module password.
3
Press YES.
1. The command is sent to the output.
2. The output executes the command.
3. When the execution of the command is finished, a result popup is displayed with a failure or success
message.
4
DOCA0037EN-01 04/2014
Operation
Device View for Acti 9 Smartlink Devices
Overview
For each submenu selected in the left tab of the main area, a headpiece allows you to navigate through
the tabs. Press the corresponding tab title to display it.
Data displayed in the Device view screen depends on the Acti 9 Smartlink device. Refer to the relevant
user guides.
Each Acti 9 Smartlink device concentrates data from connected devices on its channels.
Monitoring Information
Depending on the type of the connected device, the Device view displays:
 The status of the device
 The energy measured by the device
 Buttons to control other devices connected to the device
The layout of the Device view for an Acti 9 Smartlink device is as follows:
Control
DANGER
HAZARD OF ELECTRIC SHOCK


Check that the downstream electrical equipment is safe.
Check that you control the appropriate circuit breaker.
CAUTION
HAZARD OF CLOSING ON ELECTRICAL FAULT
Do not close the circuit breaker again without first inspecting and, if necessary, repairing the downstream
electrical equipment.
DOCA0037EN-01 04/2014
41
Operation
The procedure to control an Acti 9 Smartlink device is as follows:
Step
Action
1
In the submenu Control, press the action (Open or Close) for the target device.
2
Press YES.
1. The command is sent to the device.
2. The device executes the command.
3. When the execution of the command is finished, a result popup is displayed with a detected failure
or success message.
3
Setup
The Setup view allows you to configure the channels of an Acti 9 Smartlink device.
For each channel to configure:
Step
Action
1
In the Setup menu, select the channel C•.
2
Select the type of the device connected on this channel.
Examples of types: OF+SD24, Pulse Counter, iACT24.
NOTE: The selection of a device type not corresponding to the connected device can lead to misleading
information.
42
3
If you selected the type Pulse Counter, check the box of the input pulse counters for this channel.
Edit the label and name for each checked pulse counter.
4
Edit the label and name of the associated device.
5
Once you have configured all channels, press OK to exit the Setup menu.
DOCA0037EN-01 04/2014
FDM128
Update and Maintenance
DOCA0037EN-01 04/2014
Chapter 5
Topic
DOCA0037EN-01 04/2014
Page
Software Update
44
Monitored LV Device Update
46
Regular Cleaning
47
Troubleshooting Checklists
48
Protecting the Environment
49
43
Software Update
Prerequisites
To update the FDM128 display for 8 LV devices software, you have to get a USB stick.
This USB stick must be:
 Formatted in FAT32 system format
 Empty
DANGER
HAZARD OF ELECTRICAL SHOCK


Ensure that the zone is safe before connecting or disconnecting the USB key.
Use the USB connector for a temporary connection during maintenance and configuration of
equipment.
Software Download
Step
Go to the Schneider Electric home page www.schneider-electric.com.
2
In the Search box, type the reference of the FDM128 display unit (LV434128) or the name of the product
offer (FDM128).
 Do not include leading or trailing blank spaces in the search string.
 To get information on similar modules, use asterisks (*).
3
If you entered the reference, go to the Product datasheets search results.
If you entered the name of the product offer, go to the Product Offer search results.
Click the link of the FDM128 display unit product.
4
Click Documents & Downloads, then click Software/Firmware.
The list of available software for the FDM128 display unit is displayed.
5
44
Action
1
Click the link FDM128xxx.zip or the download icon
download.
Save the .zip file on your computer.
of the FDM128 software version you want to
DOCA0037EN-01 04/2014
Installation
After downloading the software, update the FDM128 display unit as follows:
Step
DOCA0037EN-01 04/2014
Action
1
Extract files from the .zip file.
2
Load the extracted files in the USB memory key.
3
Plug the USB key to the FDM128 display unit in the USB1 port.
4
Follow the instructions displayed on the FDM128 screen.
45
Monitored LV Device Update
Adding New LV Devices
Step
1
Action
Ensure that settings of the new LV devices are compliant with the prerequisites (see page 30).
2
Press the
icon to update the FDM128 communication settings (see page 33).
Removing Selected LV Devices
Step
1
Action
Disconnect the LV devices from the network.
2
Press the
icon to update the FDM128 communication settings (see page 33).
Replacing Micrologic
After replacing a Micrologic trip unit, press the
(see page 33).
icon to update the FDM128 communication settings
Adding or Removing a Device Connected to an Acti 9 Smartlink Device
Step
46
Action
1
Depending on your needs:
 Connect the device to the Acti 9 Smartlink device.
 Disconnect the device from the Acti 9 Smartlink device.
2
Open the Acti 9 Smartlink Device view (see page 41) and press the Setup button.
3
Select the channel of the device to add or remove.
4
If you are:
 Adding a device, set the device type and enter the label and the name of the device.
 Removing a device, set the device type to Not configured.
DOCA0037EN-01 04/2014
Regular Cleaning
Cleaning the Display
NOTICE
EQUIPMENT DAMAGE



Power off the FDM128 before cleaning it.
Do not use hard or sharp objects to operate the touch panel since it can damage the panel surface.
Do not use paint thinner, organic solvents, or a strong acid compound to clean the FDM128.
Failure to follow these instructions can result in equipment damage.
When the surface or the frame of the display gets dirty, soak a soft cloth in water with a neutral detergent,
wring the cloth tightly, and wipe the display.
DOCA0037EN-01 04/2014
47
Troubleshooting Checklists
Introduction
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH


Electrical equipment should be installed, operated, serviced, and maintained only by qualified
personnel.
Before working on the equipment, ensure that you are working in a safe area
When a problem is detected, go through the checklist and follow the instructions given.
Possible problems that could occur when using a FDM128 display unit are:
 Panel display is blank.
 Connected equipment cannot be used.
 Panel does not respond or responds slowly.
 Panel beeps when powered on.
 Cannot change the date or time.
NOTE: Contact your local Schneider Electric vendor or your local distributor.
Panel Display Is Blank
If the display is blank, perform the following check steps:
Step
Check/Operation
Solution
1
Is the FDM128 display unit using the correct
rated voltage?
Verify the power supply connections and levels.
2
Is the power supply off or disconnected?
Follow the instructions in the Instruction Sheet to
reconnect the power supply.
3
Is the backlight lit?
Potential detected problem with the FDM128 display
unit. Contact your local Schneider Electric distributor.
4
Is the problem resolved?
If none of the previous steps fixed the blank panel
display detected problem, then verify the hardware.
Display Replacement
The FDM128 display can be replaced by the spare part reference HMIS85.
Connected Equipment Cannot Be Used
If the FDM128 display unit does not communicate with connected equipment, perform the following check
steps:
Step
48
Check/Operation
Solution
1
Is the power supply off or disconnected?
Verify the power supply connections and levels.
2
Is the communication cable connected
correctly?
Refer to the FDM128 display for 8 LV devices
Instruction Sheet for information about cable diagrams.
3
Is the problem resolved?
If none of the previous steps fixed the communication
problem, then check the hardware.
DOCA0037EN-01 04/2014
Protecting the Environment
Recycling Packaging
The packaging materials from this equipment can be recycled. Please help protect the environment by
recycling them in appropriate containers.
Thank you for playing your part in protecting the environment.
End-of-Life Recycling
At end of life, the FDM128 display unit has been optimized to decrease the amount of waste and valorize
the components and materials of the product in the usual end of life treatment process.
The design has been achieved so components are able to enter the usual end-of-life treatment processes
as appropriate: depollution if recommended, reuse and/or dismantling if recommended to increase the
recycling performances, and shredding for separating the rest of materials.
DOCA0037EN-01 04/2014
49
50
DOCA0037EN-01 04/2014
FDM128
DOCA0037EN-01 04/2014
Appendices
DOCA0037EN-01 04/2014
51
52
DOCA0037EN-01 04/2014
FDM128
FDM128 Icons
DOCA0037EN-01 04/2014
Appendix A
FDM128 Icons
FDM128 Icons
Icon List
Header Icons
Icon
Description
Go to General view menu
Go to Editing devices menu
Go to Communication settings menu
Go to General settings menu
Footer Icons
Icon
Description
Go to next screen
Go to previous screen
Switch to bargraph mode
Switch to numeric mode
Switch to dial mode
Action Icons
Icon
Description
Reset measures or counters
Reset circuit breaker
Decrease level
Increase level
Display next tabs
Display previous tabs
DOCA0037EN-01 04/2014
53
FDM128 Icons
Alarm Status Icons
Icon
Description
Circuit breaker status is OK
Circuit breaker is offline
Medium priority alarm is occurring
High priority alarm is occurring
Circuit Breakers Status Icons
Icon
Description
Circuit breaker is charged
Circuit breaker is discharged
Circuit breaker is closed
Circuit breaker is open
Withdrawable circuit breaker is connected
Withdrawable circuit breaker is disconnected
Capacitive load
Inductive load
Test active
Test disabled
54
DOCA0037EN-01 04/2014
DOCA0037EN-01
Schneider Electric Industries SAS
35, rue Joseph Monier
CS30323
F - 92506 Rueil Malmaison Cedex
www.schneider-electric.com
As standards, specifications and designs change from time to time, please ask for confirmation
of the information given in this publication.
04/2014

FDM128 - Display for 8 LV Devices - User Guide

Transcription

Similar documents

Bangstick 90 Degree NFDD Delivery Pole

Three-Breaker Automatic Throwover

Grab Coffee Breaker

Series 70 ePODs: Type-X

www.chlorofil

Series 70 ePODs: Type-X - LayerZero Power Systems, Inc

TB-CDP02-TX/RX

The one and only!

Enerlin`x - Schneider Electric