fire fighting equipment

fire fighting equipment
industry, oil and gas
our expertise, your safety
NOHA NORWAY AS – leading supplier of fire fighting equipment
NOHA NORWAY AS was founded in 1924 and has grown to become a world leading manufacturer of fire hose
reels and cabinets. NOHA started manufacturing hose reels early in the 1950’s and has since focused on developing
­solutions and extending the product range to cover all fire fighting equipment for the residential- and commercial
­markets. We are therefore proud to be able to supply fire fighting equipment according to our customers’ needs.
And, we have the competence needed to come up with safe and smart solutions. Such solutions are best found
through communication with our customers.
Extensive range of certified quality products
Is it possible to buy safety? Actually, yes. Feeling safe is based on being prepared. In case of fire, feeling safe is
based on having high-quality fire fighting equipment available when you need it.
In addition to a wide range of quality products for the residential- and consumer markets, we offer our customers what
is needed to be prepared,including service and maintenance. We also offer training and counseling. Regarding
quality, there is no compromise.
Renovating or building new?
If you involve us in your plans at an early stage, we can find practical and esthetical solutions. This will provide you
with the safety you deserve: Not only design-wise, you will also save money.
www.noha.no
You will find updated information about NOHA, our products and solutions on our website.
2
NOHA NORWAY AS • www.noha.no CONTENT
CONTENTPage
CONTENT
Page
NOHA OFFSHORE HOSE REELS
SILVANI MONITORS
22
AKRON MONITORS
23
4
Model S11& S11SW
Model S13
Model S21 &Model S81
Oscillating Flange
Model S81F & S81F in Cabinet
Model S84 & S86
Model S89 & NOHA Utility Frame
PORTABLE FOAM EQUIPMENT
24
FOAM CONCENTRATES
25
FIRE SUPPRESSION SYSTEMS
27
Model S91 & S96
NOHA OFFSHORE OPTIONS
13
NOHA Offshore Hose
Documentation and other options
Argonite Inert Gas System
Hose Guides
Self-Acting Suppression
Hose Reel Fittings
Wet Chemical Suppression System
NOHA NOZZLES 15
AKRON NOZZLES
16
FIRE HOSE
18
Duraline
DELUGE SYSTEMS
28
CONTROL VALVES
29
SPRINKLERS AND WATER SPRAY NOZZLES
30
FIRE EXTINGUISHERS 32
RESPIRATORY PROTECTION DEVICES
35
GAS DETECTION
37
RENTAL EQUIPMENT 38
SERVICE AND MAINTENANCE
39
Coverlite
Hydra
General Purpose
FIRE FITTINGS
19
NOR Couplings
Storz Couplngs
Standpipes
DUAL AGENT
20
ANGUS MONITORS
21
NOHA NORWAY AS • www.noha.no 3
•
NOHA MODEL S11 & S11SW
noha fixed offshore hose reel for wall-mounting
Gunmetal piping parts, for sea water.
For use in accommodation and living quarters, drilling areas, production areas offshore and at
petrochemical plants.
NOHA model S11 is supplied with:
Model
Hose Length
25 mm
Dimensions in mm
Order number
Dry Weight
S11
0m
550 x 230
400 001
12 kg
S11
20 m
550 x 230
400 002
30 kg
S11
0m
550 x 275
400 003
12 kg
S11
25 m
550 x 275
400 004
35 kg
S11
0m
650 x 275
400 005
13 kg
S11
30 m
650 x 275
400 006
40 kg
S11
0m
700 x 175
400 007
14 kg
S11
20 m
700 x 175
400 008
32 kg
S11
0m
700 x 220
400 009
14 kg
S11
25 m
700 x 220
400 010
37 kg
ØxD
• Hose reel made of galvanized steel
• Piping parts gunmetal
• Paint according to NOHA offshore
specification
for galvanized steel, RAL 3000 red
• Oil resistant, antistatic rubber hose with
working pressure 20 bar, and pressed SST
hose couplings
• Water supply through the centre of the reel
• Hose coupling reel end: 1” BSP female,
swivel, gunmetal
• Hose coupling nozzle end: 1” BSP male,
fixed, gunmetal
• Bolts and nuts in stainless steel
• Water inlet 1” BSP male
• Design pressure 20 bar
• Design temperature –9/+35ºC
• NOHA installation instructions
• Nozzle, stop valve and documentation are
not included
• Options: See page 13-15
NOHA SWINGING OFFSHORE HOSE REEL FOR WALL-MOUNTING
Gunmetal/stainless steel piping parts, for sea water.
For use in accommodation and living quarters, drilling areas, production areas offshore and at
petrochemical plants.
NOHA model S11SW is supplied with:
• Hose reel made of galvanized steel
• Piping parts gunmetal/stainless steel
• Paint according to NOHA offshore specification for galvanized steel, RAL 3000 red
• Oil resistant, antistatic rubber hose with w
orking pressure 20 bar, and pressed SST hose
couplings
• Mounting template
• NOHA swinging arm with internal waterways,
hinged on right hand side
• Hose coupling reel end: 1” BSP female,
swivel, gunmetal
• Hose coupling nozzle end: 1” BSP male,
fixed, gunmetal
• Water inlet 1” BSP male
• Bolts and nuts in stainless steel
• Design pressure 20 bar
• Design temperature –9/+35ºC
• NOHA installation instructions
• Nozzle, stop valve and documentation are
not included
• Options: See page 13-15
H
A
B
Model
Hose Length
25 mm
Dimensions in mm
Order number
Dry Weight
S11SW
0m
715 x 650 x 235
560 208
17 kg
S11SW
20 m
715 x 650 x 235
560 209
35 kg
S11SW
25 m
715 x 650 x 235
560 202
40 kg
S11SW
30 m
715 x 650 x 235
560 203
44 kg
C
WxHxD
D
D
E
W
4
NOHA NORWAY AS • www.noha.no •
NOHA model S13
NOHA FIXED OFFSHORE HOSE
REEL FOR WALL-MOUNTING
Titanium piping parts, for sea water.
For use in accommodation and living quarters,
drilling areas, production areas offshore and at
petrochemical plants.
NOHA model S13 is supplied with:
• Hose reel made of galvanized steel
• Piping parts titanium grade 2
•
•
•
•
•
•
•
•
• Paint according to NOHA offshore specification
for galvanized steel, RAL 3000 red
• Oil resistant, antistatic rubber hose with working
pressure 20 bar, and pressed SST hose couplings
• Water supply through the centre of the reel
• Hose coupling reel end: 1” BSP female, swivel, titanium
Model
Hose coupling nozzle end: 1” BSP male, fixed, gunmetal
Water inlet 1” BSP male
Design pressure 20 bar
Design temperature –9/+35ºC
Bolts and nuts in stainless steel
NOHA installation instructions
Nozzle, stop valve and documentation are not included
Options: See page 13-15
Hose length
Dimensions in mm
25 mm
ØxD
Order number
Dry weight
S13
0m
S13
20 m
550 x 220
400 031
12 kg
550 x 220
400 032
S13
30 kg
0m
550 x 275
400 033
S13
12 kg
25 m
550 x 275
400 034
35 kg
S13
0m
650 x 275
400 035
13 kg
S13
30 m
650 x 275
400 036
40 kg
S13
0m
700 x 175
400 037
14 kg
S13
20 m
700 x 175
400 038
32 kg
S13
0m
700 x 220
400 039
14 kg
S13
25 m
700 x 220
400 040
37 kg
NOHA NORWAY AS • www.noha.no 5
•
NOHA model S21
NOHA OFFSHORE HOSE REEL IN STAINLESS STEEL
CABINET FOR WALL-MOUNTING
795.0
H
Gunmetal piping parts for sea water.
Hose reel mounted on a swinging arm with internal waterways, which swings 180o.
For use in accommodation and living quarters, drilling areas, production areas offNOHA MODEL S21
shore and at petrochemical plants.
W
792.0
NOHA Model S21
310
D
50
50
Gunmetal piping parts, for sea water.
Model
S21
Hose Length
25 mm
Dimensions in mm
30 m
795 x 795 x 310
Order number
Dry Weight
WxHxD
560 201
70 kg
Model
Hose length
25mm
Dimension in
mm
WxHxD
Order
number
Dry
weight
S21
30m
795 x 795 x 310
560201
70 Kg
NOHA model S21 IS supplied with:
•
•
•
•
•
•
•
S11 hose reel made of galvanized steel (S21)
Water inlet 1” BSP male
Water supply through the centre of the reel
Hose coupling reel end: 1” BSP female, swivel, gunmetal
Hose coupling nozzle end: 1” BSP male, fixed, gunmetal
Piping parts gunmetal
Oil resistant, antistatic rubber hose with working
pressure 20 bar, and pressed SST hose couplings
• Supply hose
• Cabinet model made in 1,5 mm stainless steel AISI 316L
• Door fitted with rubber gasket and hinges on right hand side
6
• One throw-over door catch
• Ø 35 mm knockouts for inlet pipework on 2 sides
• Paint according to NOHA offshore specification for
galvanized steel/ stainless steel, RAL 3000 red
• Design pressure 20 bar
• Bolts and nuts in stainless steel
• Design temperature –9/+35ºC
• NOHA installation instructions
• Nozzle, ball valve and documentation are not included
• Options: See page 13-15
NOHA NORWAY AS • www.noha.no •
NOHA model S81
OFFSHORE FIRE HOSE REEL FOR FLOOR- OR WALL-MOUNTING
Gunmetal piping parts, for sea water.
For use in production areas offshore and at petrochemical plants, and on helideck together
with foam.
NOHA model S81 is supplied with:
• Hose reel made of galvanized steel
• Piping parts gunmetal
• Paint according to NOHA offshore specification
for galvanized steel, RAL 3000 red
• Oil resistant, antistatic rubber hose with working
pressure 20 bar, and pressed SST hose couplings
• 1:3 rewind gearing device with attachable hand-crank
• Water inlet 2” BSP male left hand side
• Design pressure 20 bar
• Design temperature –9/+35oC
• Water supply through the centre of the reel
Model
Hose length
25 mm
31 mm
•
•
•
•
•
•
•
•
•
•
Hose coupling reel end 25mm: 1” BSP female, swivel, gunmetal
Hose coupling nozzle end 25mm: 1” BSP male, fixed, gunmetal
Hose coupling reel end 31mm: 1” BSP female, swivel, gunmetal
Hose coupling nozzle end 31mm: 1” BSP male, fixed, gunmetal
Hose coupling reel end 38mm: 1 1⁄2 ” BSP female, swivel, ­gunmetal
Hose coupling nozzle end 38mm: 1 1⁄2 ” BSP male, fixed,
­gunmetal
Bolts and nuts in stainless steel
NOHA installation instructions
Nozzle and documentation are not included
Options: See page 13-15
Dimensions in mm
38 mm
Order number
Dry weight
WxHxD
S81
0m
430 x 740 x 660
400 050
35 kg
S81
20 m
430 x 740 x 660
400 046
54 kg
S81
25 m
430 x 740 x 660
400 045
58 kg
S81
30 m
430 x 740 x 660
400 051
62 kg
S81
0m
630 x 740 x 660
400 099
43 kg
S81
50 m
630 x 740 x 660
400 100
88 kg
S81
0m
630 x 740 x 660
400 099
43 kg
S81
30 m
630 x 740 x 660
400 053
75 kg
S81
0m
630 x 740 x 660
400 054
43 kg
S81
30 m
630 x 740 x 660
400 055
82 kg
Can be delivered in brown as a Diesel Utility Hose Reel, with recommended Design Pressure 15 Bar.
NOHA NORWAY AS • www.noha.no 7
•
NOHA MODEL S81F & S81F in cabinet
NOHA FIRE HOSE REEL WITH FOAM TANK
Gunmetal piping parts, for sea water.
For use in drilling areas, production areas offshore and at petrochemical plants, helideck
and industrial sites
NOHA model S81F is supplied with:
• Water supply through the centre of the reel
• Oil-resistant, antistatic rubber hose with working
pressure 20 bar, and pressed SST hose couplings
• Akron 3019 nozzle
• 200 litres/min. foam inductor, adjustable for
0-6% mixture of foam concentrate
• 2” SST isolating valve
• Water inlet 2” BSP female thread
• 1:3 gearing device with hand crank
• Foam tank stainless steel AISI 316L
• Design temperature 0 -/+ 35oC
• Bolts and nuts in stainless steel
• Hose reel made of galvanized steel
Hose Length
25 mm
Dimensions in mm
Order number
Dry Weight
S81F 100 L
30 m
845 x 920 x 980
S81F 200 L
30 m
155 507
135 kg
845 x 1080 x 980
560 211
141 kg
NOHA MODEL S81F
1068
178
440
711
921
H
WxHxD
590
Model
• Waterways made of gunmetal/
stainless steel
• Working pressure 3-10 bar
• Paint according to NOHA offshore
specification for ­galvanized steel,
RAL 3000 red
• Instructions for use and maintenance
• NOHA installation instructions
• Foam concentrate is not included
• Options: See page 13-15
709
W
940
D
845
980
NOHA FIRE HOSE REEL IN STAINLESS STEEL CABINET,
WITH FOAM TANK
Model
Hose length
Dimension in mm
WxHxD
Order
number
Dry
weight
Gunmetal piping parts, for sea water.
38mm
For use in drilling areas, production areas offshore andS81Fat100Lpetrochemical
plants,
helideck
and
30m
845 x 920
x 980
155507
135 Kg
S81F 200L
30m
845 x 1080 x 980
560211
141 Kg
industrial sites
S81F in cabinet is supplied with:
• Water supply through the centre of the reel
• Oil-resistant, antistatic rubber hose with working
pressure 20 bar, and pressed SST hose couplings
• Akron 3019 nozzle
• 200 litres/min. foam inductor, adjustable for
0-6% mixture of foam concentrate
• 2” SST isolating valve
• Water inlet 2” BSP female thread
• 1:3 gearing device with hand crank
• Foam tank stainless steel AISI 316L
• Design temperature 0 -/+ 35oC
• Cabinet in stainless steel AISI 316L
• Bolts and nuts in stainless steel
8
Model
Hose Length
25 mm
Dimensions in mm
Order number
Dry Weight
S81F 100 L
30 m
845 x 1175 x 990
S81F 200 L
30 m
560 212
210 kg
845 x 1335 x 990
560 213
220 kg
WxHxD
NOHA NORWAY AS • www.noha.no • Hose reel made of galvanized steel
• Waterways made of gunmetal/stainless steel
• Working pressure 3-10 bar
• Paint according to NOHA offshore
specification for galvanized steel/
stainless steel, RAL 3000 red
• Instructions for use and maintenance
• NOHA installation instructions
• Foam concentrate is not included
• Options: See page 13-15
•
NOHA MODEL S84 & S86
OFFSHORE FIRE HOSE REEL FOR FLOOR- OR WALL-MOUNTING
Stainless steel piping parts (S84) or titanium piping parts (S86), for sea water.
A brake is recommended if the reel is to be wall-mounted. For use in production areas offshore and
at petrochemical plants, and on helideck together with foam
Model
Piping parts
Hose Length
25 mm
31 mm
Dimensions in mm
38 mm
Order Number
Dry Weight
WxHxD
S84
SST
0m
430 x 740 x 660
400 068
35 kg
S84
SST
30 m
430 x 740 x 660
400 069
62 kg
S84
SST
0m
630 x 740 x 660
400 070
43 kg
S84
SST
30 m
630 x 740 x 660
400 071
75 kg
S84
SST
0m
630 x 740 x 660
400 072
43 kg
S84
SST
30 m
630 x 740 x 660
400 073
82 kg
S86
Titanium
0m
430 x 740 x 660
400 074
35 kg
S86
Titanium
30 m
430 x 740 x 660
400 075
62 kg
S86
Titanium
0m
630 x 740 x 660
400 076
43 kg
S86
Titanium
30 m
630 x 740 x 660
400 077
75 kg
S86
Titanium
0m
630 x 740 x 660
400 078
43 kg
S86
Titanium
30 m
630 x 740 x 660
400 079
82 kg
NOHA model S84 and S86 are supplied with:
•Hose reel made of galvanized steel
• Hose coupling nozzle end 25mm: 1” BSP male, fixed, ­gunmetal
• S84: Piping parts 316L forged austenitic stainless steel
• Hose coupling reel end 31mm: 1” BSP female, swivel, 316L (S84)
• S86: Piping parts titanium grade 2
or titanium (S86)
• Paint according to NOHA offshore specification
for galvanized steel, RAL 3000 red
• Hose coupling nozzle end 31mm: 1” BSP male, fixed, ­gunmetal
• Hose coupling reel end 38mm: 1 1⁄2 ” BSP female, swivel, 316L
• Oil resistant, antistatic rubber hose with working
pressure 20 bar, and pressed SST hose couplings
(S84) or titanium (S86)
• Hose coupling nozzle end 38mm: 1 1⁄2 ” BSP male, fixed, gunmetal
• 1:3 rewind gearing device with hand-crank
• Bolts and nuts in stainless steel
• Water inlet 2” BSP male left hand side
• NOHA installation instructions
• Design pressure 20 bar
• Nozzle and documentation is not included
• Options: See page 13-15
• Design temperature –9/+35oC
• Water supply through the centre of the reel
• Hose coupling reel end 25mm: 1” BSP female, swivel, 316L
(S84) or titanium (S86)
Can be delievered in light blue (RAL 5015) as a Plant Air Utility Hose Reel, or yellow (RAL 1004) as a Utility Hose Reel Inert Gas.
Recommended Design Pressure 12 Bar. Colors according to NORSOK.
NOHA NORWAY AS • www.noha.no 9
•
NOHA MODEL S89
NOHA UTILITY HOSE REEL, HP 230 BAR
For general maintenance purposes.
NOHA model S89 is supplied with:
NOHA MODEL S89
622
D
W
409
739
372
H
660
328
Model
S89
•
Hose Length
10 mm
Dimensions in mm
0m
380 x 740 x 660
314
Order number
Dry Weight
400 171
35 kg
WxHxD
Model
Hose length
10mm
Dimension in
mm
WxHxD
Order
number
Dry
weight
S89
0m
380 x 740 x 660
400171
35 Kg
NOHA UTILITY FRAME
NOHA UTILITY FRAME
For Hose Reel 314. Carbon Steel construction. Color RAL 7038 according to
NORSOK 501.
Model
Order number
NOHA Utility Frame
281 979
•
•
•
•
10
1:
2:
3:
4:
Support frame
Plate 20 mm
Plate 5 mm
Plate 5 mm
NOHA NORWAY AS • www.noha.no • Hose reel made of galvanized steel
• Piping parts AISI 316L stainless steel
• Paint according to NOHA offshore
specification
for galvanized steel, RAL 6002 green
• Water supply through the centre of the reel
• Reel inlet:1⁄2” NPT male thread left hand side
• Hose connection to reel 3/8” BSP female
thread, 60o cone
• Hand crank for rewind
• Bolts and nuts in stainless steel
• Design pressure 230 bar
• Design temperature –5,5/+95oC
• NOHA installation instructions
• Hose and documentation are not included
• Options: See page 13-15
•
NOHA model s91 & S96
NOHA DUAL AGENT FIRE HOSE REEL
Gunmetal (S91) or titanium (S96) piping parts for foam and powder. For use in drilling
areas, production areas offshore and
petrochemical
plants and helideck
NOHAat
MODEL
S91
920 /1020
W
D
530
409
328
739
682
H
660
574 /674
NOHA MODEL S91
Gunmetal piping parts for foam and powder.
Model
Hose Length
25 mm
31 mm
S91
0m/0m
S91
30 m / 30 m
S91
0m
S91
30 m
0m
30 m
Dimensions in mm
Order number
Dry Weight
WxHxD
670 x 740 x 660
400 090
670 x 740 x 660
400 091
770 x 740 x 660
400 092
Model
Hose length
43
kg
25mm
31mm
S91
S91
S91
770 x 740 x 660
400 093
Dimensions in mm
Order number
S91
100 kg
0m/0m
48
kg
30m/30m
0m
0m
120
30m kg
30M
Dimension in mm
WxHxD
670 x 740 x 660
Order
number
400090
Dry
weight
45Kg
670 x 740 x 660
400091
100Kg
770 x 740 x 660
400092
50Kg
770 x 740 x 660
400093
120Kg
NOHA MODEL S96
Titanium piping parts for foam and ­powder.
Model
Hose Length
25 mm
31 mm
Dry Weight
WxHxD
S96
0m/0m
670 x 740 x 660
400 102
43 kg
S96
30 m / 30 m
670 x 740 x 660
400 103
100 kg
S96
0m
0m
770 x 740 x 660
400 104
48 kg
S96
30 m
30 m
770 x 740 x 660
400 105
120 kg
NOHA model S91 AND S96 is supplied with:
• Hose reel made of galvanized steel
• Piping parts gunmetal (S91)
• Foam bearing parts titanium grade 2 (S96)
• Powder bearing parts gunmetal (S96)
• Paint according to NOHA offshore specification
for galvanized steel, RAL 3000 red
• 2 x 30m oil resistant, antistatic hose laid in
a lay flat hose cover
• 1:3 rewind gearing device with hand-crank
• Reel inlet 2 x 2” BSP male
•
•
•
•
•
•
•
•
•
Design pressure 12 bar
Design temperature –9/+35oC
Hose couplings reel ends: 1” BSP female, swivel, gunmetal
Hose couplings nozzle end: 1” BSP male, fixed, gunmetal
Dual piping through the centre of the reel
Bolts and nuts in stainless steel
NOHA installation instructions
Nozzle and documentation are not included
Options: See page 13-15
accesories:
• NOHA dual agent nozzle, see page 15
NOHA NORWAY AS • www.noha.no 11
•
NOHA OFFSHORE Options & aCCEsSORIES
NOHA OFFSHORE HOSE REELS (HORISONTAL) FEATURES
FOR FLOOR OR WALL MOUNTING
2,5 mm galvanized steel sheets
STANDARD FEATURE
2 mm stainless steel sheets
OPTIONAL FEATURE
page13
2 layer painting (epoxy powder/polyester powder)
for galvanized steel STANDARD FEATURE
1 layer painting (polyester powder) for stainless steel
STANDARD FEATURE
page13
Nozzle OPTIONAL FEATURE
page 15-17
1:3 rewind gearing device STANDARD FEATURE
1:3 front rewind gearing device OPTIONAL FEATURE
Fixed roller hose guide
OPTIONAL FEATURE
page14
page13
Hand crank for rewind STANDARD FEATURE
Inlet fitting 2” BSP Male
OPTIONAL FEATURE
page14
Piping parts according to
customer requirements
NOHA offshore HOSE
Oil resistant, antistatic rubber hose with working pressure 20 bar.
NBR lining and Polyester reinforcement. Cover: NBR/ EPDM.
Dimension
12
Length
(mm)
(m)
25
20
Bronze
1 “ BSP Female
Bronze
1 “ BSP Male
218 639
25
25
Bronze
1 “ BSP Female
Bronze
1 “ BSP Male
218 640
25
30
Bronze
1 “ BSP Female
Bronze
1 “ BSP Male
217 236
25
50
Bronze
1 “ BSP Female
Bronze
1 “ BSP Male
218 641
31
25
Bronze
1 “ BSP Female
Bronze
1 “ BSP Male
222 947
31
30
Bronze
1 “ BSP Female
Bronze
1 “ BSP Male
217 237
38
25
Bronze
1
1/2
“ BSP Female
Bronze
1
1/2
“ BSP Male
225 763
38
30
Bronze
1
1/2
“ BSP Female
Bronze
1
1/2
“ BSP Male
217 238
25
20
Titan Gr 2
1 “ BSP Female
Bronze
1 “ BSP Male
221 499
25
25
Titan Gr 2
1 “ BSP Female
Bronze
1 “ BSP Male
221 505
25
30
Titan Gr 2
1 “ BSP Female
Bronze
1 “ BSP Male
221 485
31
25
Titan Gr 2
1 “ BSP Female
Bronze
1 “ BSP Male
224 811
31
30
Titan Gr 2
1 “ BSP Female
Bronze
1 “ BSP Male
221 475
38
30
Titan Gr 2
25
25
AISI316 L
1 “ BSP Female
Bronze
1 “ BSP Male
221 498
25
30
AISI316 L
1 “ BSP Female
Bronze
1 “ BSP Male
221 496
31
30
AISI316 L
1 “ BSP Female
Bronze
1 “ BSP Male
221 493
38
30
AISI316 L
1
1
1/2
1/2
“ BSP Female
“ BSP Female
Material
Bronze
Bronze
NOHA NORWAY AS • www.noha.no Nozzle Fitting
Thread Type
Order number
Swiwel Fitting
Material
Thread Type
1
1
1/2
1/2
“ BSP Male
“ BSP Male
221 476
221 486
•
NOHA OFFSHORE OPTIONS & aCCESsORIES
PAINTING, DOCUMENTATION AND OTHER OPTIONS
Options:
Order number
Optional Paint Spec (RAL _ _ _ _)
226 821
Basic Documentation Package
226 817
Full Documentation Package
226 818
NORSOK/Other Documentation Package
226 819
Other options (specify from chart below)
226 820
Documentation packages
Basic documentation:
• General assembly drawing
• Materials certificate for piping parts
(316L / titanium)
or Materials datasheet for piping
parts (gunmetal)
• Pressure test certificate
Full documentation:
• General assembly drawing
• Project plan
• Quality plan
• Materials certificate for piping parts
(316L / titanium)
or Materials data­sheet for piping
parts (gunmetal)
• Traceability log for piping parts
(316L / titanium)
• Pressure test certificate
• Painting report
NORSOK/Other documentation:
• To be quoted after customer
requirement
OTHER OPTIONS
When ordering other options without order number, please use number 226 820 and specify the additional feature.
Model
Anti-clockwise
rotation
S11
Opposite Hinge
Steel
Position
1:3 Front Rewind
Insulated
2
Heater
Gearing Device
3
Optional Utility
Hose Reel
4
X
X
S13
X
X
S21
X
X
S81
1
X
X
S11SW
Stainless
X
S81F
X
X
X
X
X
X
X
S84 & S86
X
X
X
S89
X
X
X
X
X
S81F in cabinet
X
Diesel
X
X
Plant Air
or Inert Gas
S91 & S96
Stainless Steel
Hose Reel sheet metal parts made of Stainless Steel.
1
2
Insulated
S21: Cabinet insulated with 20 mm mineral wool protected by galvanized steel cover.
S81F in cabinet: Cabinet insulated with 20 mm mineral wool protected by 1 mm stainless steel cover.
3
Heater
200W with Junction box. II 2G , EEx e II T4.
Optional Utility Hose Reel
Hose Reel can be delievered as a Utility Hose Reel, with color according to NORSOK.
4
NOHA NORWAY AS • www.noha.no 13
•
NOHA OFFSHORE OPTIONS & aCCEsSORIES
Hose guides
Hose guide adjusts to the proper working angle with a nut adjustment.
Material
Compatible with Model
Order number
Hose Guide 314
Galvanized Steel
S81, S84, S86, S89
218 417
Hose Guide 314
AISI 316L
S81, S84, S86, S89
219 524
Hose Guide 514
Galvanized Steel
S81, S81F, S84, S86
215 244
Hose Guide 514
AISI 316L
S81, S81F, S84, S86
218 290
OFFSHORE HOSE REEL FITTINGS
Length between inlet adapter / flenge and reel fixation hole (L) is 60 mm.
Other connection fittings and materials available on request.
L
Inlet adapters
Material
Reel Fitting
Bronze
Bronze
AISI 316L
AISI 316L
Connection Fitting
Compatible with Model
Order Number
2” BSP Female
1 1/2 “ BSP Male
S81, S89, S91
226 822
2” BSP Female
1 1/2 “ NPT Male
S81, S89, S91
226 580
2” BSP Female
1 1/2 “ BSP Male
S84
223 017
2” BSP Female
1 1/2 “ NPT Male
S84
212 547
Titanium, grade 2
2” BSP Female
1 1/2 “ BSP Male
S86, S96
226 826
Titanium, grade 2
2” BSP Female
1 1/2 “ NPT Male
S86, S96
213 854
Outer flange fittings
Reel Connection Fitting
Compatible with Model
Order Number
Bronze
1 1/2 “ BSP Female
S81, S89, S91
226 831
Ansi B16,5 150# RF
Bronze
1 1/2 “ NPT Female
S81, S89, S91
226 830
Ansi B16,5 150# RF
AISI 316L
1 1/2 “ BSP Female
S84
281 020
Ansi B16,5 150# RF
AISI 316L
1 1/2 “ NPT Female
S84
226 829
Ansi B16,5 150# RF
Titanium, grade 2
1 1/2 “ BSP Female
S86, S96
282 043
Titanium, grade 2
1 1/2 “ NPT Female
S86, S96
226 828
Flange
Material
Ansi B16,5 150# RF
Ansi B16,5 150# RF
14
NOHA NORWAY AS • www.noha.no •
NOHA NOZZLES
NOHA Gunmetal Nozzles
CE-approved when used togheter CE-approved NOHA Hose Reel.
Model
Inlet Connection
Length
Weight
Order number
D7
3/4” BSP Male
120 mm
0,7 kg
222 740
D 10
3/4” BSP Male
120 mm
0,7 kg
222 796
Capasity and throw length
Pressure ahead of the inlet valve, measured against open nozzle. Applies to
NOHA offshore hose reels with up to 25mm 30 m hose.
= D7
= D10
55
50
180
D10
160
140
120
D7
100
80
60
THROW LENGTH (m)
FLOW RATE (lPM)
220
200
45
40
35
25
20
15
40
10
20
5
3
6
9
12
15
D7
D10
30
18
PRESSURE (bar)
3
6
9
12
15
18
pRESSURE (bar)
NOHA Dual Agent Nozzle
Dual Agent nozzle can discharge water/AFFF foam solution and dry chemical
extinguishing agent. The side by side valves handles allow dry chemical and
AFFF/water agent to be discharged seperately or simultaniously.
To be used with NOHA Dual Agent Hose Reel.
Model
Inlet Connection
Order number
Dual Agent Nozzle
1 1/2” BSP Female
224 154
NOHA NORWAY AS • www.noha.no 15
•
NOZZLES
Akron Turbojet Nozzles
1702 1 " Turbojet Nozzle with Pistol Grip
SOLAS & approved available (Must specify)
• Flow setting at 100 psi (7 bar) operating pressure can be used for high pressure
applications up to 580 psi (40 bar) hydrostatic pressure
• Use Quick-Attack Foam Tube Style 755
1717 1 1⁄2" Turbojet Tip with Twist Shutoff
1720 1 1⁄2" Turbojet Nozzle with Pistol Grip
1717 & 1720:
• 100 psi (7 bar) standard, 75 psi (5 & 6 bar) optional
• Compatible with Quick Attack Foam Tube Style 766
Style
“ (206 mm)
9
1/4
” (38 mm)
7
1/4
” (38 mm)
9
1/2
1” (25 mm)
1717
1
1/2
1720
1
1/2
2
” (232 mm)
4
LPM
15-25-40-60
50-100-150-230
135 034
(1kg)
30-60-95-125
115-230-360-475
135 082
(1,8kg)
30-60-95-125
115-230-360-475
135 002
3 (1,4kg)
“ (175 mm)
Order number
Flow Settings
GPM
lbs. (kg)
1702
Style 1717
*
Weight
Length
Swiwel Inlet
Style 1720
1/4
* FM Approved Styles 1702 & 1720 100 psi (7 bar) rated pressure configartion
Akron Brass Fog Nozzles
A combination fog and straight stream nozzle designed for efficiency with foam or water on offshore
rigs and in industrial applications.
3019 & 3021
1 1⁄2” Brass Fog Nozzle with Pistol Grip and Molded Teeth
• Rubber-like bumper and handle
• Constant gallonage in fog and straight stream patterns
• Flush without shutting down
• Repair kits available
• Compatible with 775 Quick Attack™ Foam Tube for Styles 3015-3021
Length
Inlet
Style
Weight
lbs. (kg)
(3,5kg)
95
360
135 009
“ (219 mm)
7
(3,5kg)
125
475
135 023
” (38 mm)
8
3021
1
Order number
3/8
5/8
1/2
LPM
3/8
5/8
1/2
GPM
7
8
1
Flow at 100 Psi (7 bar)
” (219 mm)
” (38 mm)
3019
Style 3019
Akron Turbomaster™
A family of multi-flow Master Streams adjustable to four constant flow settings.
• Pattern detents for positive stream positioning
Style 1745
Style
16
Material
Pattern
Flow at 100 Psi (7 bar)
Control
GPM
LPM
Inlet
Teeth
Length
Weight
Order number
1745
Pyrolite
Manual
250-440550-750
250-440550-750
2 1/2”
(65 mm)
Spinning
9”
(241 mm)
11
(5,4 kg)
135 036
1755
Pyrolite
Manual
250-440550-750
250-440550-750
2 1/2”
(65 mm)
Spinning
10”
(229 mm)
13
(5,7 kg)
135 035
NOHA NORWAY AS • www.noha.no •
NOZZLES
Akron Assault Nozzles
•
•
•
•
Quick change pattern adjustment
Specify pressure and flow, see chart
Optional 6 bar available
Compatible with Quick-Attack Foam Tube Style 777
4720 4820 1 1⁄2” Assault Nozzle with Pistol Grip and Molded Teeth
1 1⁄2” Assault Nozzle with Pistol Grip and Spinning Teeth
Style
Length
Inlet
Style 4820
Order number
Weight
lbs. (kg)
” (213 mm)
3
3/4
(1,7kg)
135 012
“ (213 mm)
4
1/4
(1,9fkg)
135 004
” (38 mm)
8
3/8
” (38 mm)
8
3/8
4720
1
1/2
4820
1
1/2
NOZZLE
BAR
230
@
7
360
@
5
360
@
7
475
@
5
475
@
7
3
159
295
254
386
333
550
@
3
550
@
5
550
@
7
660
@
5
660
@
7
750
@
7
401
541
469
534
**
**
All pressure/flow configurations with exeption of 550 lpm @ 5 bar
Actual LPM
550
462
5
197
360
310
475
409
696
550
492
660
575
655
7
230
416
360
545
475
802
655
550
765
660
750
Akron Aquastream™
A fixed gallonage master stream nozzle designed for heavy-duty use on fixed
monitors.
• With grease fitting
Style 4452
Style 4450 only
Style
Material
Pattern
Control
4450
Brass
Manual
4452
Pyrolite
Manual
Flow at 100 Psi (7 bar)
GPM
LPM
Inlet
Teeth
Length
Weight
Order number
500
1900
(300 & 750)* (1140 & 2900)*
500
1900
(300 & 750)* (1140 & 2900)*
2 1/2”
(65 mm)
Fixed
7”
(178 mm)
14 1/2
(6,6 kg)
135 020
2 1/2”
(65 mm)
Fixed
7”
(178 mm)
4 3/4
(2,2 kg)
135 402
* Field changeable spacers included with nozzle
Akron Rampage™
A fixed gallonage master stream nozzle with built-in stream shaper designed for
flows up to 1250 gpm. Ideal for heavy-duty use on fixed monitors. Style 4460
has twist shutoff.
Style 4460
Style 4461 only
Style
Material
Pattern
Flow at 100 Psi (7 bar)
Control
GPM
4460
Brass
Manual
4461
Brass
Manual
Inlet
Teeth
Length
Weight
Order number
2 1/2”
(65 mm)
None
9”
(229 mm)
23 1/4
(10,5 kg)
135 416
2 1/2”
(65 mm)
None
9”
(229 mm)
23 1/4
(10,5 kg)
135 083
LPM
750 (500,
2900 (1900,
1000 & 1250)* 3800 & 4800)*
750 (500,
2900 (1900,
1000 & 1250)* 3800 & 4800)*
* Factory set at 750 gpm - field changeable to 500 or 1000 gpm, spacers included with nozzle. Must specify 1250 gpm.
NOHA NORWAY AS • www.noha.no 17
•
FIRE HOSE
DURALINE FIRE HOSE
The world’s premier maintenance-free covered fire hose for municipal and industrial fire service.
Significantly exceeds the requirements of the most demanding international standards for resistance to kinking, abrasion, heat, chemicals, oil, weathering, ultraviolet light and ozone. Unique
construction means Duraline can be wiped down after an incident and returned to storage without
drying. Simple repair techniques are available to ensure damaged hose can be quickly and safely
returned to service.
Designed for the longest possible s torage and service life. Used in every imaginable environment
around the world, from arid desert to arctic tundra, Duraline has proven longevity over years of
storage and service. Exceptional robustness and storage properties ensure Duraline remains in
operational service many years after imitation products have proven to be false economies.
COVERLITE FIRE HOSE
A high performance covered fire hose with an economic price for industrial and municipal fire services.
Lightweight and highly flexible for easy handling. Resistant to kinking, abrasion, heat, chemicals, oil,
weathering, ultra-violet light and ozone.Unique construction means Coverlite can be wiped down after an
incident and returned to storage without drying.
Tough and durable for the longest possible storage life in every imaginable environment around the world,
from arid desert to arctic tundra. Exceptional robustness and storage properties ensure Coverlite remains in
operational service many years after imitation products have failed.
HYDRA - SINGLE JACKET FIRE HOSE
A lightweight and exceptionally rugged conventional fire hose that combines performance with
economy.
Hydra offers the very latest in lightweight hose technology. Unique fully synthetic construction combines maximum performance with lightest weight for fast and easy hose handling. While retaining
its lightweight and compactness, Hydra A is also tough and durable giving reduced damage during
operational use. Hydra B offers enhanced abrasion resistance due to its external polyurethane coating.
Synthetic construction means Hydra hose can be wiped down after an incident and returned to storage ready for use without drying
or any maintenance. Sturdy rot-proof textile reinforcement is totally immune to mildew. Highly ozone resistant synthetic rubber lining.
Gives excellent performance in all climatic conditions from arid desert to arctic tundra.
GENERAL PURPOSE HOSE
A flexible layflat covered hose for all types of industrial maintenance and water transfer operations.
Offers major cost savings and performance advantages over conventional uncovered hose.
Lightweight construction ensures it never gets wet and heavy, allowing it to be quickly and easily
cleaned with no need for drying out.
Its easy to handle, lightweight, highly flexible and resistant to kinking. Distinctive blue colour clearly
identifies it as a maintenance hose. Also available in black and yellow.
Lightweight and compact for economical storage in standard maintenance truck.
Designed for long service life with minimal maintenance. Tough and durable with exceptional resistance to abrasion and cutting.
Resistant to heat, fuels, chemicals, UV, ozone, weathering, hydrolysis, and microbiological attack.
18
NOHA NORWAY AS • www.noha.no •
FIRE FITTINGS
NOR Couplings
NOR fittings are designed for pairing of pipes, hoses, spray tips etc.. for use in fire fighting and flushing with
water. Used by Norwegian fire departments, municipalities, water and sewage facilities etc. couplings, which are
of claw principle, be connected each other with two equal parts, ie not male or female, but “unisex”.
The new NOR Coupling is able to withstand pressure up to 60 Bar.
NOR Couplings come in 3 different lock sizes - lock 1, lock 2 and Lock 3 - from the largest to the smallest. On
the opposite side of the “claw” is the interface to the hose or tubes, tube socket in various dimensions (from 1 - 3
“) or pipe threads, interior / exterior (BSP) (from 1-3 “). Lock 2 is used mostly in the marine / offshore sector.
LockDimesnions “LD”Dimensinos “Ø”
Lock 1
83 mm
1
Lock 2
65 mm
1” - 2”
” - 3”
Lock 3
50 mm
1” - 1
1/2
”
1/2
Hose Tail
Storz Couplings
Storz fittings are designed for connection of hoses, pipes, pumps etc., for use in the transport of water, such as fire fighting and flushing with water. These couplings, which is also the claw principle, are to be linked to each other with 2 equal parts, ie not male or
female, but "unisex".
LockDimesnions “LD”Dimensinos “Ø”
Storz D 31 mm
1”
Storz 32 44 mm
1” - 1
1/2
Storz 38 50 mm
1” - 1
1/2
Storz C
66 mm
1
1/2
Storz 65
81 mm
1
1/2
Storz B
89 mm
2” - 3”
”
”
” - 2”
” - 3”
Storz 100
115 mm 4”
Storz A 133 mm 4” - 4
Storz 125
148 mm 5”
Storz 150
160 mm 6”
Storz 165
188 mm 7”
Storz 205
200 mm 8”
”
1/2
Standpipes
NOR Standpipes come as a standard in aluminum single or double outlet and at a height of about 75 cm. Top of the outlet is a NOR
coupling lock 1.
Standpipes
NOR Single Delivery Standpipe
NOR Single Delivery Standpipe 1500
NOR Double Delivery Standpipe
NOR Double Delivery Standpipe 1500
NOHA NORWAY AS • www.noha.no 19
•
DUAL AGENT
Dual Agent Units are manually operated hose reel stations, discharging dry chemical powder and water/foam, intending to
be used by trained fire fighting personnel. The Dual Agent hose reel is supplied with two individual hoses, where one hose is
intended for dry chemical and the other for water/foam. The hose reel is equipped with a dual agent nozzle that has individual
open/shut valves, and with a twist-action selection of jet or fog on the water/foam side, giving full control of the two agents.
Dual Agent Units are rapidly activated, and they are simple to use. The dry chemical powder gives a rapid knockdown of
large scale fires, while water/foam gives cooling of hot surfaces and sealing of liquid pool fires. The Dual Agent Units must be
installed in the vicinity of the area they are to protect.
These hose reels are extremely efficient units for protection of areas containing hydrocarbons or alcohols, such as helicopter
decks and process areas.
Typical main components:
• Cabinet
• Hose Reel
• Dual Agent Nozzle
• Dry chemical system, with N2 propellant
• Foam system
• Firewater inlet
Foam and powder supply
NOHAs standard Dual Agent Hose Reels are supplied as a skid mounted system,
enclosed in a heated stainless steel cabinet. The unit includes an inlet connection
for supply of firewater.
The
•
•
•
foam may be supplied to the unit and mixed into the firewater in the following ways:
Through a balanced pressure proportioner, from local pressurized foam tank.
Through a balanced pressure proportioner, from the platform foam ring-main system
Though an in-line inductor, from a local or external atmospheric foam tank.
The system is supplied with a dry chemical vessel in requested material, and foam/waterways in materials suitable for use with
seawater/foam. The powder is supplied from a pressure vessel, which is pressurized by a N2 Cylinder.
20
NOHA NORWAY AS • www.noha.no •
Angus MONITORS
Monitors are used to apply water, foam or dual agents wherever there are large quantities of flammable or combustible liquids.
NOHA offers a wide variety of monitors from small to big flow from portable to apparatus-mounted to fixed site systems. Storage and
process areas, in the oil and petrochemical sectors are the most common applications. In the world of transport they are found on
shipping and loading jetties, airport crash tenders, aircraft hangars and helicopter landing areas. 1,800 - 4,000 l/min
Max throw 80m
Portable / mobile
Hand lever with
friction locks
Hand wheel* with
worm and wheel
gearbox
PMA 18
SS
A PMS 27-37
1,800 l/min 2,700 - 3,700 l/min
4,000 - 5,900 l/min
Max throw 90m
PMB 40
SS
4,000 l/min
6,000 - 7,900 l/min
Max throw 95m
PMB 65
B
6,500 l/min
LMB/A 30 B A
3,000 l/min
LMS 30
SS
3,000 l/min
LMB 40
B
4,000 l/min
LMS 45
SS
4,500 l/min
LMS 60
SS
6,000 l/min
LMB 65
B
6,500 l/min
GMA 30
A
3,000 l/min
GMS 30
SS
3,000 l/min
GMB 50
B
5,000 l/min
GMS 45 SS
4,500 l/min
GMS 60 SS
6,000 l/min
GMB 65
B
6,500 l/min
*Chain drive optional
Automatic
oscillating
gearbox
Hydraulic drive
OMB 36
B
3,600 l/min
OMB 40
B
4,000 l/min
OMB 65
B
6,500 l/min
RHMA 30 A
3,000 l/min
RHMB 50
B
5,000 l/min
RHMS 60 SS
6,000 l/min
RHMB 65 B
6,500 l/min
RHEMA 30 A
3,000 l/min
RHEMB 50 B
5,000 l/min
RHEMS 60 SS
6,000 l/min
RHEMB/C 65 B
6,500 l/min
REMA 30 A
3,000 l/min
REHMB 50 B
5,000 l/min
REMS 60 SS
6,000 l/min
REMB 65 B
6,500 l/min
(EExd rated)
Hydraulic drive
with electro/ hydro
power packs
(EExd rated)
Electric drive
(EExd rated)
B
A
Bronze
Alloy
SS
Stainless Steel 316
NOHA NORWAY AS • www.noha.no 21
•
SILVANI MONITORS
3,000 - 4,000
l/min
Lynx PGM65
3,000 l/min
Portable
monitors
6,000 - 8,500
l/min
MSS65 - FM
approved
MSS08 B
4,000 l/min
MSS08 - AU
4,000 l/min
Leo 80-CMA SL
6,000 l/min
Leo 80-CV SL
6,000 l/min
Leo 100-CV SL
8,000 l/min
Tiger CV B
8,500 l/min
Leo 100-CMA
8,000 l/min
B
SL
Tiger AU B
8,500 l/min
Tiger TCE B
8,500 l/min
Electric
operated
monitors
Hydraulic
operated
monitors
Leo 80-TCO SL
6,000 l/min
Tiger TEO B
6,500 l/min
Leo 100-TCO
8,000 l/min
Tiger TCO B
8,500 l/min
SL
Leo 80- TCE SL Leo 80-TEO SL
6,000 l/min
6,000 l/min
Electro-hydraulic
operated
monitors
B
22
Bronze
Alloy
Jaguar CV 250 SS
60,000 l/min
Tiger CC B
8,500 l/min
Direct chain
operated
monitors
A
Leo 150-CV SL
20,000 l/min
B
3,000 l/min
Self oscillating
monitors
40,000 - 60,000
l/min
A
MSS65 B
3,000 l/min
Manual
operated
monitors
20,000 - 30,000
l/min
Leo 100-TCE SL Leo 100-TEO
8,000 l/min
8,000 l/min
SS Stainless
SL
Steel 316
Stainless Steel 316L
NOHA NORWAY AS • www.noha.no SL
Lion CV SL
30,000 l/min
Lion TCE SL
40,000 l/min
Leo 150-TCO SL
20,000 l/min
Lion TCO SL
40,000 l/min
AKRON MONITORS
•
1,000 - 3,000
l/min
Portable
monitors
4,000 - 6,000
l/min
Memory Quick
Attack monitor
1,900 l/min P
3443
6,000 - 8,000
l/min
Akron Apollo
4,800 l/min P
3423
Akron Omega
4,800 l/min B
3526
Manual
operated
monitors
Akron Aries
4,800 l/min B
3525
OZZIE™ monitor
1,420 l/min P
911
Self oscillating
monitors
Akron Ozzie Master
950 - 2,900 l/min P
9220
Electric
operated
monitors
Akron Deckmaster
4,800 l/min P
3440
Akron Conquest
7,600 l/min B
3678
Akron Streammaster
7,600 l/min P
3598
B
P
Bronze
Pyrolite
Oscillating Flange for Brass Monitor 4" flange x 4" flange unpainted
The Style 3531 is capable of flows to 1500 gpm at an oscillation range up to
165° and is compatible with most Akron Brass manual monitors.
Its unique maintenance-free polymer bearing design, high quality material construction and superior performance make it the ideal choice for a long-term, low
service solution for protecting your hazardous and harsh environments.
3531 with monitor.
NOHA NORWAY AS • www.noha.no 23
•
PORTABLE FOAM EQUIPMENT
HI-COMBAT Low Expansion Foam Branchpipes
Rapid fire protection for sites where flammable and hazardous liquids are stored and processed. To get the best results from these
branchpipes it is recommended to use with either Tankmaster Fluoroprotein foam or Alcoseal AR-FFFP multi-purpose foam concentrate.
•
•
•
•
Exceptionally long reach of highest quality, cohesive, low expansion foam rope.
Oil resistant, synthetic rubber ring protects against accidental damage.
Nominal flow rates of 225, 450 and 900 l/min at 7 bar g.
Self-inducting 3% versions of F225/SI and F450/SI models supplied with foam pick-up
tube and piercer.
HI-COMBAT Medium Expansion Foam Branchpipes
Angus MEX Branchpipes produce medium expansion foam which is effective in a wide range of fires involving both flammable liquids
and solids. Fabricated in stainless steel the units are tough, lightweight and compact, fitting easily into fire appliance lockers. They
produce long throws of a coherent foam stream at low pressures and the high volume of foam produced gives rapid coverage over
a large area but with minimum water usage. This makes them ideal for rapid foam cover in outdoor situations or for enclosed fires
where total flooding with foam is possible.
•
•
•
•
•
•
Minimal water consumption and subsequently reduced water damage.
Highest quality, stable medium expansion foam.
Low operating pressures, 2.5 bar g. optimum.
Matched to UNI-225 and UNI-450 inductors.
Ideal for rapid vapour suppression and fire control over large surface areas.
Bulky foam helps cover objects and keep pipes, valves and flanges cool.
HI-COMBAT Anderson Pourers
Each unit produces a large volume of free flowing stable MEX foam, providing rapid coverage of the bunded area. Such gentle foam
application minimises contamination of the foam by the fuel.
These units are particularly effective when used with Angus fluoroprotein and film forming fluoroprotein foam concentrates (eg FP70
and Alcoseal). The cohesive nature of FP/FFFP foams also minimises the effects of wind.
•
•
•
•
Fast, effective delivery of highest quality, medium expansion foam into bunded
(diked) region surrounding bulk fuel storage tank in the event of fire or spillage.
Simply carry to edge of bund, and leave to operate without need for further
supervision.
Dedicated MEX Foam Inductors are available for optimum performance.
Bulky foam helps keep pipes, valves and flanges cool.
HI-COMBAT Turbex Mk ll
High capacity, high expansion foam generator. Ideal for total flooding applications (e.g. basements, mines, tunnels, cable ducts,
warehouses). Powered by water turbine and aerofoil fan, all that is required for operation is pressurised water supply and Angus Fire
Expandol high expansion foam concentrate.
•
•
•
•
24
Minimal water consumption and subsequent water damage.
Unique water by-pass system allows performance to be maintained while working
against high back pressures.
Expendable polythene ducting ensures accurate foam delivery.
Ideally suited for rapid smoke extraction and positive pressure ventilation. Smoke
extraction ducting easily attached with quick release strap.
NOHA NORWAY AS • www.noha.no •
PORTABLE FOAM EQUIPMENT
HI-COMBAT AF120 Mk2 Mobile Foam Unit
The HI-COMBAT AF120 Mk2 Mobile Foam Unit operates with maximum effectiveness when filled with Niagara 3-3 AR-FFFP, the
world’s most advanced high performance fire fighting foam.
•
•
•
•
•
•
Ideal for rapid deployment of foam to flammable liquid fires and chemical spills.
Exceptional fire fighting capability can make the difference between a fire being a minor inconvenience and a major disaster.
Easily manoeuvred and operated by one person.
Simply connect to pressurised water supply to operate.
Comprises chemically resistant 120 litre glass fibre foam concentrate tank with built-in
hose storage compartments and large diameter filler cap, variable foam inductor with
shut-off valve, foam branchpipe, foam pick-up tube, and two lengths of Angus Fire
Duraline hose.
Ideal for oil storage and loading terminals, process areas, paint and solvent stores,
engine rooms, aircraft hangars, maintenance areas, and all similar high risk areas.
HI-COMBAT Foam Uniductors
Angus Hi-Combat Portable Foam Uniductor, when matched with Angus Hi-Combat Foam branchpipes or nozzles, provides the
simplest possible means of getting foam to the fire where it is needed. They can be placed near a portable pump or hydrant outlet,
minimising manpower requirements and leaving the firefighter to concentrate on effective application of the foam to control the fire
situation. Available in 1-3 & 3-6 versions
•
•
•
•
•
•
•
Simplest and most accurate means of inducting foam concentrate into water stream.
Foam pick-up rates 1%, 1%AR, 3%, 3%AR for 1-3 version and 3%, 3%AR, 6%, 6%AR for 3-6 version designed to meet the latest stringent NFPA 11 accuracy criteria.
Simple TWIST control knob cannot be accidentally moved during operation.
Special energy recovery system limits pressure loss across Uniductors to 35-40%, retaining maximum pressure for foam projection.
Matched and colour coded to branchpipes with flow rates of 225 and 450 l/min at 7 bar g. 900 l/min inductor also available.
Standard in Light Alloy, but corrosion resistant Gunmetal also available.
FOAM CONCENTRATES
Multipurpose Foam
Niagara, Alcoseal and Tridol ATF are versatile alcohol-resistant foam suitable for use on hydrocarbons and flammable liquids.
Niagara is a universal, or alcohol-resistant foam, that may be used in a large number of risk cases where hydrocarbons and solvents
are present. What distinguishes it from other universal foams is that it contains no polymer additives. This means there is less sticky,
or in other words, more liquid, and thus flows freely through pumps and pipes and achieve good accuracy in all types of dispensing
equipment.
Film Forming Fluorprotein (FFFP)
Petroseal FFFP is the world’s leading foam for airport fire services. It combines the speed of AFFF with
the post-fire security of FluoroProtein. Petroseal is a Film Forming Fluoroprotein (FFFP) foam – the only
type of foam to successfully combine the rapid fire knockdown of conventional film forming foams with
the level of security and burn back resistance unique to fluoroproteins. Petroseal FFFP is used by Aircraft
Rescue and Fire Fighting Services at international airports in over 50 countries worldwide.
NOHA NORWAY AS • www.noha.no 25
•
FOAM CONCENTRATES
Fluorprotein (FP)
Tankmaster™ is a superior quality FluoroProtein (FP) fire fighting foam concentrate for extinguishing and securing flammable hydrocarbon liquid fires. In particular it is a powerful and cost-effective agent for the protection of a wide range of hydrocarbons including
crude oil, regular leaded gasoline, unleaded gasoline containing up to 20% Methyl Tertiary Butyl Ether (MTBE), and pure MTBE.
Aqueous Film-Forming Foam (AFFF)
Tridol S premium grade AFFF produces a thin aqueous film that shoots ahead of the foam blanket to provide
exceptionally fast flame knockdown and extinguishment. It is available in 1, 3 and 6% grades and also a
number of low temperature versions. Tridol C standard grade AFFF combines performance with
affordability, while Tridol M AFFF is US Mil Spec grade.
High Expansion (Hi Ex)
Expandol produces large-volumes of high expansion foam for use in total flooding applications, marine fire fighting and Liquefied
Natural Gas (LNG) applications. It is used in combination with the Turbex Mk2 portable high expansion foam generator or Fixed
Turbex foam equipment.
Expandol used at medium and high expansion combats fires in three ways:
• Initial contact with fire generates a large volume of steam reducing the available oxygen to
create an inert atmosphere.
• The high water content of medium expansion foam produces a valuable cooling effect.
• The large volume of foam generated engulfs the area and totally seals off and extinguishes
any remaining fires.
Class A
Forexpan S is used at 0.1 to 1.0% depending on the application method. It meets the requirements of the US Department of Agriculture Forest Service and NFPA 1150 Standard on Fire Fighting Foam Chemicals fo Class A Fuels in Rural, Suburban and Vegetated
Areas (1999).
Forexpan S is a synthetic fire fighting foam concentrate specially formulated for Class A applications such as forestry and wildland fire
control, structural fires, and tyre and paper fires. The balanced chemical system in Forexpan reduces the surface tension of water to
increase the penetrating power into burning Class A materials.
Fluorine-Free Foam (F3)
Syndura ia an award-winning operational F3 Foam for securing flammable hydrocarbon liquid fires.
F3 training foams mimic the foam properties of front-line operational foams, enabling firefighters to train and test equipment and
vehicles with minimal envrironmental impact. TF3 and TF6 mimic Petroseal 3 & Petroseal 6; and Trainol 3 & 6 mimic Angus AFFF 3%
& 6% Foams respectively. TFAL3 Mimics Angus AR-FFFP 3% Foam.
•
•
•
•
•
26
World’s first operational Fluorine Free Foam (F3) for minimal environmental impact.
Ideal for civilian and military airport fire services.
Fully approved to UL 162, ICAO Level A, UK Def Stan 42-42, and EN 1568-3.
Outstanding performance in realistic aircraft crash fire tests carried out by UK Defence Fire Service.
Exceptionally stable in long-term storage.
NOHA NORWAY AS • www.noha.no •
FIRE SUPPRESSION SYSTEMS
Argonite inert gas system
Argonite is a blend of argon and nitrogen gases that occur naturally
in the atmosphere. It is popular with organisations that prefer to use a
non-chemical suppression agent. With zero ODP, zero GWP and zero
atmospheric lifetime, Argonite has excellent environmental credentials.
It works by displacing oxygen and reducing from the normal 21% to a
level that will not support combustion. A typical design concentration
of 40% will reduce the oxygen level to 12.5% within 60 seconds. In
occupied areas personnel can continue to breathe safely at this level
for short periods of time.
Argonite is used for the purpose of fighting fires in almost all combustible materials. It can extinguishing fires in
flammable liquids. Argonite is not electrically conductive and therefore very suitable for extinguishing fires in electronic equipment
Self-acting suppression
The effectiveness of this system comes from the red detection tubing that ruptures when exposed to a
flame. The specialized tubing combines leak resistance, flexibility, durability and precise temperature
sensitivity, allowing it to react quickly when the heat from a fire is present. The flexible, narrow tubing
is particularly applicable in small spaces and connects to one of the custom engineered valves and a
cylinder that contains the best fire suppression agent for the particular hazard: powder, foam, water, or
CO2.
Designed for simple installation, often very near the source of a potential fire, the system is a self-activating suppression system that reliably suppresses fires in seconds. No electricity required.
Wet Chemical suppression system
24-hour automatic or manual protection for commercial cooking areas; ducts, plenums, hoods and cooking surfaces. Wet chemical
agent designed for quicker flame knockdown and faster suppression.
Exceeds stringent UL 300 standard and complies with NFPA Standards 96 and 17A. Offers unmatched coverage, with fewer discharge nozzles and flow points, meaning reduced installation time and cost.
Features:
•
•
•
Safe and reliable fire protection
Ease of design and flexibility of installation
Flexibility and reliability of important safety system
Listings/Approvals:
Underwriters Laboratories, Inc. (UL 300) Listed
Underwriters Laboratories of Canada (ULC/ORD 154C.6) Listed
NYC MEA Approved
American Bureau of Shipping (Type Approval)
Det Norske Veritas (Type Appproval)
Lloyds Register of Shipping (Type Approval)
ISO 15371
EC (TPED) models available
NOHA NORWAY AS • www.noha.no 27
•
DELUGE SYSTEMS
Deluge Systems are named from the ’deluge’ of water they provide when activated. A Deluge System is normally the main fire fighting
system on any offshore installation, used to protect process or drilling areas and other high risk sites. The Deluge system is normally an
automatic system, which is triggered by a fire detector in the protected area, and which is using water as the extinguishing agent. The
most basic Deluge System consists of only 3 parts: Deluge Control Valve, distribution pipework and Deluge Nozzles.
Deluge system application
A Deluge system may be used to protect almost any area as it provides:
• Flame extinguishment
• Cooling
• Fire control
Deluge systems, using water or water/foam, will extinguish fires in any, or in a combination, of the following ways:
• Surface cooling
• Smothering, by produced steam
• Emulsification
• Dilution
• Other factors
Except in very rare cases, where the application of water may cause certain chemicals to burn or explode, Deluge systems will have
a beneficial effect on all types of fires. Even in cases, such as fire in leaking, pressurized Gas equipment, where flame extinguishment
cannot be achieved, the overall cooling effect, with the resulting protection of adjacent equipment, will prevent the fire from spreading
and will greatly reduce the damage to both equipment and structure.
Deluge Systems are used for:
Hydrocarbon fires:
• Wellhead Area • Drill Floor
• Process Areas
Gas
•
•
•
•
(Jet) fires:
Wellhead Area
Drill Floor
Process Areas
Storage and Piping facilities
Fire in Solids:
• Chemical Storage
Multivalve deluge Skid
Multivalve deluge skids are suitable for use in compact installations such as offshore platforms, where the distance between protected
areas is limited. All our deluge skids are based on the C300 deluge control valve. Valve and piping materials may be titanium, duplex
stainless steel etc. Skid enclosures are made from stainless steel, insulated and heated if required. Skids are available with foam proportioning facilities, and can be equipped with full size test lines for realistic functional testing.
Single deluge skid
Single valve deluge skids are available for installations where it is necessary to install the valve skid adjacent to the protected area.
The valve skid uses the C300 deluge control valve. The standard design for all deluge skids is with rigid lightweight corrugated
stainless steel enclosure. Deluge skids can also be supplied as open skid units. The valve skids will normally include a manual by-pass
valve. The systems are available with instrument air control, or direct firewater control for system release.
Deluge valve skid with integrated foam tank
Deluge valve skids are available with different types of foam supply arrangements. Foam can be supplied pressurized from a central
foam unit, or with the foam tank integrated into the skid design as part of the corrugated stainless steel enclosure at the back of the
unit. Mixing of foam into the firewater can be achieved by use of balanced pressure foam proportions, foam inductors, constant flow
foam valves, or water driven foam proportioning pumps.
Foaming agents, such as AFFF (Aqueous Film Forming Foam), is very effective against Hydrocarbon pool fires. Cooling is used to
protect structural members and equipment from heat radiation, due to an on-going fire, so that major damages and fire propagation is
avoided.
28
NOHA NORWAY AS • www.noha.no •
CONTROL VALVES
The C300 high performance fluid control valve is an extremely versatile wafer type unit with a varied
number of options and applications. The valve was developed in conjunction with major oil companies
to perform in harsh offshore petrochemical environments and in use today throughout the world.
It is capable of wide flow range with comparatively low pressure losses and can provide
accurate pressure control for many uses. The unit, with its accessories can be used for
applications where upstream or downstream pressure sensing is required.
The C300 is available in a range of sizes from 80mm (3” nominal) to 300mm (12” nominal) and in
standard range of materials for all environments.
C300 Valve Features & Benefits
• High performance
• Wide flow range
• Low pressure loss
• Accurate pressure control
• Avoids cavitation
• Compatibility of materials
• Low maintenance - common component
• Surge protection
Sizes
• 3”
• 4”
• 6”
• 8”
• 10”
• 12”
Types
• Non-Regulating
• Deluge
• Sprinkler
• Pump Control
• Pressure Control
C300 Variants; Deluge with Pressure Control
• System pressure control
• Air operated on/off option
• Fast opening option
• Surge Protection
C300 applications
NOHA NORWAY AS • www.noha.no 29
•
sprinklers and water spray nozzles
ANGUS FYRHED - High velocity water spray nozzle
The Angus Fyrhed high velocity water spray nozzle is intended for use in engineered fire protection systems to give exposure protection
to capital equipment. The water velocity and droplet size are engineered to provide good exposure protection of capital equipment
where a significant throw is required or when the nozzle is positioned outside where high wind speeds may be encountered.
The Fyrhed nozzle is also suitable for controlling fuel fires involving high viscosity, high flashpoint (above 66ºC) fuels, or for use with
foam-water mixes to achieve additional fire protection especially on flammable liquids.
Each nozzle incorporates a unique swirl in the water passage designed to give an even distribution of water throughout the cone. The
minimum passage clearance in the swirl is 4.5mm, which when combined with the 3mm mesh inlet filter minimises the possibility of
blockage.
Strainer ø3 mesh
1” NPT
Techincal specification
Material: Naval Brass to ISO CuZn385ul orCuZn35Ni
Stainless Steel to ASTM 316
Stainless Steel SMO 254 to UNS S31254
Titanium to ASTM B367, Grade 2
Finishes: Natural, Electro Nickel Plated, Nedox coating
Operating Pressure:Min. 3,5 Bar (2,8 Bar indoors). Max 5,0 Bar.
Weight:A to C 232 g
D to K 436 g
Strainer ø3 mesh
1/2“ NPT
Type D to M
Type
Thread Size
LPCB* approved
Bore mm
K ± 3%
A
B
C
M
L
D
E
F
G
H
I
K
1/2 “ NPT
1/2 “ NPT
1/2 “ NPT
1” NPT
1” NPT
1” NPT
1” NPT
1” NPT
1” NPT
1” NPT
1” NPT
1” NPT
x
x
x
4,0
6,0
8,0
7,6
9,0
10,0
12,0
14,0
16,0
18,0
20,0
22,5
7
18
26
27
38
44
61
78
99
107
115
160
x
x
x
x
x
x
x
Type A to C
Cone Angle
+0%/ -10%
40º
50º
75º
45º
60º
60º
78º
60º
60º
66º
70º
90º
Fyrheds with selected K factors are also available with extra wide spray angles.
ANGUS THERMOSPRAY - Medium velocity water spray nozzle
The Angus Thermospray medium velocity spray nozzle is designed to produce a solid cone of evenly distributed water droplets, the
majority of which are less than 0.4mm Ø. The water velocity at the nozzle exit lies between 15 and 25 m/sec when used within the
recommended operating pressure range of 1.4 to 3.5 bar. Above 3.5 bar the droplet size decreases reducing the fire plume penetration and increasing the risk of spray pattern distortion by wind.
The Angus Thermospray is designed primarily for use in engineered fire protection systems to provide exposure protection or to
combat fuel fires with a flashpoint below 66ºC. Where fast flame knock down and security against burn back are important Angus
Foam-Water nozzles should be considered.
For protection of risks involving fuels with a flashpoint above 66ºC, for exposed protection, long throws or where high wind speeds
are expected Angus Fyrhed high velocity nozzles should be used.
30
NOHA NORWAY AS • www.noha.no •
sprinklers and water spray nozzles
ANGUS THERMOSPRAY
1/2 “ NPT (Standard)
Techincal specification
Material:DZR to ISO CuZn36Pb2AS
Stainless Steel to ASTM 316
Stainless Steel SMO 254 to UNS S31254
Titanium to ASTM B367, Grade 2
Finishes: Natural, Electro Nickel Plated, Nedox coating
Operating Pressure:Min. 1,4 Bar. Max 3,5 Bar.
LPCB Approved
K-Factor
± 5%
23*
32
38
41
50
63
78
92
115
Weight ~ 110 g
1/2 “ BSPT (Special Order)
Alternative K factors and angles
Bore mm
Spray Angles
7,5
8,7
9,4
9,7
10,6
11,5
12,4
13,1
14,0
60º
75º
90º
100º
110º
120º
135º
150º
K-Factor
± 5%
18*
26*
28
30
33
43
59
80
Bore mm
6,8
8,0
8,2
8,3
8,8
9,8
11,3
12,3
Spray Angles
65º
110º
125º
140º
* Fitted with filter
ANGUS MODEL S2 & S2 QR
Standard respons sprinkler & Quick respons sprinkler
The Angus “S” range of miniature automatic sprinklers offers the very latest in design and performance, being both highly compact
and durable. In addition, every “S” sprinkler is fitted with the unique Angus double grooved seal. The Angus “S” range is manufactured at the company’s purpose built European factory which is assessed to ISO 9001:2000 “S2” sprinklers are CE marked EN
12259-1 and approved by LPC and FM and other leading national and international approval authorities.
Angus “S” sprinklers are manufactured in brass, stainless steel, and titanium.
Techincal specification
Nominal Bore:
Weight: Thread: Max. working pressure:
System test pressure:
Factory test pressure:
Bulb Temperatures: K factor:
RTI-Value:
15 mm
69 g (Brass)
1/2” BSPT (NPT also available)
12,5 Bar
20 Bar
30 Bar
57ºC/68ºC/79ºC/93ºC/141ºC/182ºC
S2
S2 QR
80 ± 4 (metric)
80 ± 3 (metric)
S2
S2 QR
~ 100 (metric)
< 50 (metric)
Water distribution
Finishes available include chrome plated, electro nickel
plated, white painted (to RAL 9010). Custom coloured
paint finishes are also available to order.
NOHA NORWAY AS • www.noha.no 31
•
noha fire EXTINGUISHERS
PRESSURISED POWDER EXTINGUISHERS
NOHA pressurised powder extinguishers, so-called ”universal” extinguishers, are especially suitable for fire fighting
at an early stage of a fire. The extinguishers contain ABC quality powder with high extinguishing effect and are designed to
extinguish most fires at home and at work. Suitable for fires in combustible solids, flammable liquids, flammable gasses and
electrical equipment, classes ABC. The extinguishers are easy to operate for users with basic fire fighting training and hold all
necessary approvals.
NOHA P12G
NOHA P2G
NOHA P6G
2 kg powder extinguisher.
Contains 2 kg ABC ammonium phosphate powder.
The extinguisher is small,
easy to store, and easy to
use. Areas of application
include cars, boats, and
caravans.
6 kg powder extinguisher.
Contains 6 kg ABC ammonium phosphate powder.
Areas of application include
homes, office buildings,
shopping areas, cars, and
workshops.
Model
Risk class
EN-3 effect
MED
class
Effective
Total
discharge time
weight
12 kg powder
extinguisher.
Contains 12 kg ABC ammonium phosphate powder.
Areas of application include
industrial sites, and
workshops.
Dimensions
Order number
L x W x H (mm)
NOHA P2G
ABC
13A/89B/C
Yes
11 sec.
3,3 kg
110 x 145 x 3152
420 102
NOHA P6G
ABC
43A/233B/C
Yes
17 sec.
9,1 kg
160 x 215 x 510
420 122
NOHA P12G
ABC
55A/233B/C
Yes
22 sec.
17 kg
200 x 235 x 600
420 123
FOAM EXTINGUISHERS
NOHA foam extinguishers are suitable for fighting fires in flammable liquids in addition to fires in combustible solids, classes AB. The
foam has a cooling effect, and will seal the surface of the burning liquid and thereby prevent gas evaporation and re-ignition. Foam
extinguishers are excellent supplement to powder extinguishers and fire hose reels. The extinguishers are easy to operate for users
with basic fire fighting training and hold all necessary approvals.
NOHA S9G
NOHA S6G
9 liter foam extinguisher.
Contains 9 liter premix of water and AFFF
foam.
Areas of application include office and
industrial buildings, garages, printing works,
gas stations and other areas with petroleum
products and flammable liquids. For long life
and safe use, the inside of the container is
coated to avoid corrosion.
6 liter foam extinguisher.
Contains 6 liter premix of water and AFFF
foam.
Areas of application include office and
industrial buildings, garages, printing works,
gas stations and other areas with petroleum
products and flammable liquids. For long life
and safe use, the inside of the container is
coated to avoid corrosion.
Model
Risk class
EN-3 effect
MED
class
32
NOHA S6G
AB
21A/183B
NOHA S9G
AB
27A/233B
Yes
Effective dis-
Total
charge time
weight
Dimensions
Order number
L x W x H (mm)
29 sec.
10,4 kg
182 x 242 x 530
420 151
40 sec.
14,8 kg
200 x 251 x 605
420 150
NOHA NORWAY AS • www.noha.no •
noha fire EXTINGUISHERS
GAS CARTRIDGE POWDER EXTINGUISHERS
NOHA gas cartridge stainless steel powder extinguishers are especially suitable for use where the safety
requirements are extra severe. The extinguishers are supplied with either ABC or BC high-quality powder.
Professional users will utilize the extra extinguishing effect to extinguish rather large fires. The extinguishers are
activated by pressing the stroke switch at the top, which in turn activates the internal CO2 cartridge and pressurizes
the container. Application of powder is controlled with a powder nozzle at the end of the hose. All extinguishers
are stainless steel and therefore suitable for use offshore, in maritime and other corrosive environment. Hold all
necessary approvals.
Model
Risk class
EN-3 effect
MED
class
NOHA 6BG -S
Effective
Total
discharge time
weight
Dimensions
Order number
L x W x H (mm)
Yes
27 sec.
10,9 kg
142 x 220 x 550
310 104
183B/C
Yes
19 sec.
10,8 kg
142 x 220 x 550
310 105
55A/233B/C
Yes
19,5 sec.
19,3 kg
183 x 260 x 610
310 106
BC
233B/C
Yes
17 sec.
19,3 kg
183 x 260 x 610
310 119
BC
233B/C
Yes
17 sec.
19,3 kg
183 x 260 x 610
310 120
ABC
NOHA 6BKA -S
BC
NOHA 12BG -S
ABC
NOHA 12BK -S
NOHA 12BKA-S
34A/183B/C
HAND-HELD CO2 EXTINGUISHERS
NOHA K2G contains 2 kg CO2.
NOHA K5G contains 5 kg CO2.
Areas of application include computer rooms, technical rooms, next to fuse terminal boxes, and
other electronic equipment.
Model
Risk class
EN-3 effect
MED
class
Effective dis-
Total
charge time
weight
Dimensions
Order number
L x W x H (mm)
NOHA K2G
B
34B
Yes
7,9 sec.
5,3 kg
117 x 265 x 521
420 029
NOHA K5G
B
89B
Yes
11,7 sec.
12,4 kg
162 x 333 x 668
420 025
WHEELED CO2 EXTINGUISHERS
Snowhorn with extension tube and pressure grip valve. Option: extension tube and nozzle
for use on heli-deck. Conform to standard NS-EN 1866:-1:2008.
Wheel mark in accordance to directive 96/98/EC & CE Marked in accordance to EN
1866-1 (PED 97/23/EC)
Areas of application include heli-deck, power aggregate, and switchboard room.
NOHA K10 contains 10 kg CO2, and has a 5 m hose.
NOHA K20 contains 20 kg CO2, and has a 5 m hose.
Model
Risk class
EN-1866-1
MED
Effective
Total
discharge time weight
effect class
Dimensions
Order number
L x W x H (mm)
NOHA K10
B
144 IV B
Yes
17 sec.
38 kg
1045 x 350 x 900
310 716
NOHA K20
B
144 IV B
Yes
32 sec.
68 kg
600 x 410 x 965
310 717
NOHA NORWAY AS • www.noha.no 33
•
noha fire EXTINGUISHERS
MOBILE WHEELED EXTINGUISHERS
NOHA mobile wheeled powder extinguishers are especially designed for
the most demanding risks. Therefore, they are ideal for heavy industry,
refineries, airports, oil platforms and onboard ships. The extinguishers are
supplied with either ABC or BC high-quality powder. High quality and
long duration give professional users the extra extinguishing effect to
extinguish rather large fires. The extinguishers have wheels and main body
manifactured in stainless steel to withstand the most demanding
environments. Hold all necessary approvals for the respective areas of use.
Wheel mark in accordance to directive 96/98/EC & CE Marked in
accordance to EN 1866-1 (PED 97/23/EC)
NOHA 25HG/S
NOHA 50HG/S
25 kg mobile powder extinguisher.
Contains 25 kg ABC ammonium phosphate powder.
Easy refill.
Available in stainless steel.
Aerosol propellant N2.
Working pressure14 bar.
50 kg mobile powder extinguisher.
Contains 50 kg ABC ammonium phosphate powder.
Easy refill.
Available in stainless steel.
Aerosol propellant N2
Working pressure14 bar.
NOHA 25 HKA/S
NOHA 50 HKA/S
Equivalent with BC potassium sulphate powder. Equivalent with BC potassium sulphate powder. Model
Risk class
EN-1866-1
MED
effect class
NOHA 25HG/S
Effective
Dimensions
Total weight
Order number
L x W x H (mm)
discharge time
ABC
A IVB C
Yes
35 sec.
53 kg
505 x 430 x 1060
310 701
NOHA 25HKA/S
BC
A IVB C
Yes
35 sec.
53 kg
505 x 430 x 1060
310 702
NOHA 50HG/S
ABC
A IVB C
Yes
50 sec.
84 kg
650 x 480 x 1100
310 709
NOHA 50HKA/S
BC
A IVB C
Yes
50 sec.
84 kg
650 x 480 x 1100
310 710
NOHA F6G
The 6-litre Fry Fighter extinguisher has been
Cooking oil fires, because of their high
developed to deal specifically with fires
auto-ignition temperatures are difficult to
resulting from cooking oils and fats. It has the
extinguish. Conventional extinguishers are not
capability to fight fires in deep fat fryers of up
effective for cooking oil fires, as they do not
to 75 litres capacity.
cool sufficiently or may even cause flash back,
It contains a specially formulated wet chemical
so putting the operator at risk.
which, when applied to the burning liquid,
cools and emulsifies the oil, extinguishing the
flame, sealing the surface and preventing
re-ignition.
Model
Risk class
EN-3 effeckt
class
NOHA F6G
4
34
AF
13A/75F
MED
Effective
Total
discharge time
weight
46 sec.
12,2 kg
Dimensions
L x W x H (mm)
182 x 242 x 5334
Measurement without hose, with nozzle placed in holder. Measurement with hose: 182 x 300 x 650
NOHA NORWAY AS • www.noha.no Order number
420 152
•
RESPIRATORY PROTECTION DEVICES
Fenzy Aeris Confort Type 2
• Ultra comfortable harness: cushions for comfort on the straps and belt
• Aramid straps
• 3 carrying handles and 1 attachment point for a life line
• The apparatus stays perfectly well on the shoulders and hips
• Compatible with a large number of accessories.
Weight without cylinder 4.3 kg
Autonomy and pressure Of 20 to 90 min, in 200 or 300 bar
Approved temp. -30°C/+60°C
Approvals
CE0194/0060, EN 137 Type 2, MED, SOLAS, IMO
and MSC certified
Fenzy X-Pro SCBA
Self Contained Breathing Apparatus specially developed for firefighting.
• Ultra-light back plate, adjustable to every morphology for an optimum comfort
• New “ Extreme Comfort” harness concept
• Foldable foot guaranteeing a complete protection of the high pressure system
• FENZY Quick-Fix system allowing to replace cylinder quickly and easily
• Multiple anchoring rings for accessories and fast tightening straps
• New FENZY Opti-Pro full face mask with full panoramic vision without optical distortion
Weight without cylinder
Pressure Approved temp. Approvals
3.9 kg
200 or 300 bar
-30°C/+70°C
EN 137:2006 Type 2, ISO 9001, Bureau Veritas for Marine use (SOLAS, MSC and MED)
Fenzy Bioline Automatic Secours (BAS)
Airline breathing apparatus with automatic switching device on the air cylinder, low air alarm whistle and
“Fenzy Biomask” full face mask, with 5 silicone headstraps, and “Fenzy Zenith” automatic demand valve.
10 to 15-Minute duration in escape situation. Without cylinder.
• Quick and easy to put in place, and ultra lightweight
• Low pressure acoustic alarm
• HP/MP reducer with safety valve
• Automatic switch to emergency supply
Weight without cylinder
1.9 kg
Autonomy and pressure 10 to 15 min
Approved temp. -30°C/+60°C
ApprovalsEN 402 and EN 14593,
CE0194/0060 certified
Fenzy Biomix CCBA
The Fenzy Biomix is a Closed-Circuit Breathing Apparatuses. A revolutionary concept, that combines compressed air and chemical oxygen (KO2), guaranteeing a 2 hour duration with an excellent breathing comfort.
• Easy to use
• Excellent breathing comfort: the user breathes fresh and dry air without cooling device
• No fog in the mask: moisture is eliminated by the KO2
Weight Dimensions Duration Approved Temp. 16 kg (equipped with FENZY Angel II)
630 x 340 x 220 mm
2 hr
-30°C / +70°C
NOHA NORWAY AS • www.noha.no 35
•
RESPIRATORY PROTECTION DEVICES
Fenzy Oxy-Pro
Self-rescue chemical oxygen device. Chemical self-rescuers are dedicated for evacuation from non-breathable atmospheres. They offer up to 100 minutes duration. Breathable air is regenerated by potassium
superoxyde (KO2). According to the model, they are used in confined spaces, mining and forest fire
evacuations.
Weight
2,3 kg
Dimensions 200 x 210 x 105 mm
Duration 30 minutes at 35l/min and 100 minutes at 10l/min
ApprovalEN 13794
Fenzy Bio-S-Cape
A compressed emergency escape breathing apparatus that goes into operation as soon as the bag is
opened.
• Inflatable air cushion for an automatic installation
• Acoustic alarm that does not consume any air
• Optional belt for a better hold.
Version 2L / 300 bar, coiled Aluminium, Carbon 15 mn 3.2 kg
Version 2L / 200 bar, steel 10 mn 4.3 kg
Version 3L / 300 bar banded Aluminium, Kevlar 20 mn 5.2 kg
Version 3L / 200 bar, steel 15 mn 5.2 kg
Approved Temp.
-15°C / +60°C
Approvals EN 1146: 2005, MED, SOLAS, IMO and MSC
Fenzy Opti-Pro
The FENZY Opti-Pro is part of the new generation of full face masks.
It has a very modern design combining comfort and safety, suitable for every FENZY Self-Contained
Breathing Apparatus and compatible with all models of FENZY demand valves
• Comfort: half-mask, high quality silicone interior
• Wide angle visor without optical deformation/scratch-proof polycarbonate
• They come in different sizes
• Can be mounted and dismantled without tools.
Weight
Approval 730 g
EN 136 – Class III
ER2000 Escape Hood
The ER2000 Escape hood is fully assembled for escape only. The air purifying respirator consisting of a
hood with a neck seal, an oral / nasal cup and an air-purifying filter cartridge ABEKCOP3. The
permanently attached filter cartridges protect against industrial gasses, vapours, carbon monoxide and
toxic particles.
Weight (with all components) 1150 g
Approval EN 403 Class M
36
NOHA NORWAY AS • www.noha.no •
gas detection
Multi-gas detectors
GasAlertMicro 5 Series
The GasAlertMicro 5 Series simultaneously monitor and display up to five atmospheric hazards. Available as either
the standard toxic gas model, a PID model for detecting VOCs, or an IR model for CO2 detection.
Water resistant and fully customizable to suit any application.
Rapidly switch from diffusion mode to the optional integrated pump in the feild.
Weight
Dimensions
370 g
145 x 74 x 38 mm
GasAlertQuattro
Rugged and reliable, the GasAlertQuattro four-gas detector combines a comprehensive range of features
with simple one-button operation. Suited to a wide range of industrial applications including confined space entry.
Water resistant.
Weight (with rechargeable battery)
Dimensions
338 g
130 x 81 x 47 mm
GasAlertMicroClip XT
The slim and compact GasAlertMicroClip XT provides affordable protection from atmospheric hazards. With the addition of IntelliFlashTM, this multi-gas detector offers continuous visual confirmation of detector operation and compliance. Simple one-button operation offers ultimate ease of use and significantly reduces time spent training the user.
Weight (with rechargeable battery)
Dimensions
171 g
113 x 60 x 29 mm
Single-gas detectors
GasAlertClip Extreme
As the world’s most popular and widely used zeromaintenance gas detector, the GasAlertClip Extreme offers
continuous, reliable protection. Available in two year or three year versions, this single gas detector requires no
calibration, sensor replacement, battery replacement or battery charging. Record keeping is accurate and easy with
automatic event logging.
Weight
Dimensions
76 g
28 x 50 x 81 mm
GasAlert Extreme
Designed with durability and comfort in mind, the GasAlert Extreme reliably monitors for any single gas hazard
within its wide range of available toxic gas models. With easy on/off operation, this single gas detector offers
extended longevity with a two year field-replaceable battery and sensor.
Direct, real-time readings on large LCD.
Weight
Dimensions
82 g
28 x 50 x 95 mm
NOHA NORWAY AS • www.noha.no 37
•
RENTAL EQUIPMENT & COURSES
RENTAL EQUIPMENT
In connection with audits and shutdown of the extinguishing systems offshore, we can offer the complete package as a
back-up containing fire hoses, manual and oscillating monitors, foam units, fire extinguisher and aggregate. Through
NOHA, the customer is also able to rent smoke machines, exercise extinguishers, foam equipment and various fire
equipment.
NOHA rental equipment
Some of NOHAs rental equipment:
•
Respiratory protection devices
•
Exercise equipment
•
Monitors
•
Hoses and fittings
•
Powder aggregate
•
Foam Equipment
•
Valves
Course and traning
NOHA’s courses give participants theoretical and practical knowledge that forms the basis for an understanding of fire
prevention and workplace safety.
NOHA holds open courses where it is possible for anyone to sign up. In addition to the standard courses, we offer
tailor-made courses to meet individual business needs. Most courses can be held at both the enterprise and at NOHA’s
premises. For courses held at your company site, it is assumed that there is adequate space for teaching and any practical exercises. The course certificate is issued to both the individual participant and the company.
Exercises
Practical experience with fire fighting equipment and exercises on realistic situations is crucial for the best possible
outcome the day it is serious.
NOHA’s offers include:
• Training with own products
• Evacuation in case of fire alarm
• Evacuation of smoke-filled area (smoke
machine)
• The use of markers (first aid training etc.)
• Use of hand extinguishers
Approved course and examination organiser
The Norwegian “Council for the maintenance of fire
equipment” has approved NOHA NORWAY AS as
a course and exam organizer for Red and Green
certificate for service technicians.
38
NOHA NORWAY AS • www.noha.no •
SERVICE AND MAINTENANCE
ServICE OFFSHORE
NOHA’s service engineers perform routine maintenance tasks as well as ad-hoc service and repairs within the offshore
and petrochemical industries.
Service in practice
Daily inspection should be performed by separate operations personnel. Periodic inspection and system check is
performed by NOHA, resulting in:
• Status of certificates
• Review with operations personnel
• Training / repetition in the use of equipment
• Suggestions for changes and improvements
Test station
NOHA have a test station for testing the flow and pressure conditions in pipes and valves. The test station is a closed
system. With a water reservoir of 30 m3 and a diesel driven pump, the station can carry out flow and pressure tests up
to 10 000 l / min. @ 13 bar g.
ServICE ON FIRE SUPPRESSION SYSTEMS
Knowing that an extinguishing system is working 24 hours a day all year round is reassuring, but assumes that it
carried out regular inspection and maintenance by competent person. As a service
customer of NOHA, we can take care of this for you.
Regular service secure that everything is working properly and that no changes have been
made ​​to your system documentation or construction conditions.
Maintenance in accordance with applicable law
Service intervals are defined mostly by the supplier in the aquisition document and the
service is performed in accordance with applicable regulations and manufacturers’
requirements. The task will be completed by issuance of a complete report and
documentation of certain maintenance routines.
SERVICE ON MANUAL FIRE FIGHTING EQUIPMENT
In order to maintain fire safety there must be performed routine control, inspection and maintenance of the manual fire
fighting equipment, and this must be documented. NOHA performs annual maintenance of fire fighting equipment
according to NS 3910 for portable fire extinguishers and EN 671-3 for fire hose reels. After completion of
service we issue a written maintenance report.
By entering into maintenance agreements with NOHA you get:
•
•
•
•
Mapping and listing of fire fighting equipment
Fire fighting equipment that is certified and controlled - ensuring quality and extended product life time
Our service technicians experience, advice and recommendations
A comprehensive assessment of security in the enterprise
NOHA NORWAY AS • www.noha.no 39
211580/Industry Oil & Gas/1500/07-2012
Noha Norway as
Lagerveien 25, 4033 Stavanger
Tlf. 51 81 60 00, Faks 51 81 60 01
sale@noha.no
www.noha.no