Basic Setting Instructions for IQ and IQT Actuators

Basic Setting Instructions for IQ and IQT Actuators
These instructions enable the
actuator to be configured to suit the
valve and must be carried out before
electrical start up. For complete
instructions see the installation
manual that shipped with the
actuator or refer to the publications
listed below.
1
If a new Setting Tool Pro is used with an
IQ actuator (an actuator without ‘split
screen’ text support) the ‘back arrow’
and data upload/download facility will
be unavailable.
2
1
3
E170E
E170E2
E170E3
E175E
E175E3
3. - Key Decrease/change displayed function’s value
or option setting
4. + Key Increase/change displayed function’s value
or option setting
5.
Enter displayed value or option setting
Key * Pressing the two arrow keys together returns the actuator
display to the position indication mode
5
Infra-red local operation (when enabled)
7
5.
Key Stop actuator
Fig. 1.1 IQ non-textual display
6.
Key Open actuator
If your actuator is fitted with the old Rotork IQ or
IQT main board, your display will appear as fig 1.1.
If so then follow the instructions in sections 5 and
7 to set the basic configurations for your actuator.
7.
Key Close actuator
3
8. Infra-red Transmitter Window
4
New Pro Display
New Setting Tool Pro
2
For further configuration and
settings the following publications
are available:
-
-
-
-
-
4
6
6
7
8/9
4
Fig. 2.1 IQ Pro display
If your actuator is fitted with the new Rotork IQ or
IQT Pro main board, your display will appear as fig
2.1. If so then follow the instructions in sections
6 and 8 to set the basic configurations for your
actuator.
The Setting Tool Pro (new version)
1. m Key* Display next function down
2. i Key
Display previous function up
3. k Key* Display next function across
4. o Key Display previous function across
3
12
IQ mk 1 actuator
IQ mk 2 actuator
IQ Pro actuator IQT actuator
IQT Pro actuator
The Old Rotork Setting Tool
1. m Key* Display next function down
2. k Key* Display next function across
Old Rotork Setting Tool
8
Old Rotork Setting Tools and new
Setting Tool Pro’s are fully compatible
with all IQ range actuators.
If an old Rotork Setting Tool is used
with an IQ Pro/IQT Pro actuator the data
download/upload facility will not be
available. Navigation through the menu
structure is facilitated using the ‘down’
and ‘right’ arrow keys. At the end of a
menu section pressing the arrow right
or arrow down key, as applicable, will
return the menu to the start.
2
Old (non-textual) Display
5
1
11
10
5. - Key Decrease/change displayed function’s value
or option setting
6. + Key Increase/change displayed function’s value
or option setting
7. m Key Initiate download/upload mode
8.
Enter displayed value or option setting
Key * Pressing these two arrow keys together returns the actuator
display to the position indication mode
Infra-red local operation (when enabled)
9.
Key Stop actuator
10.
Key Open actuator
11.
Key Close actuator
12. Infra-red Transmitter Window
Publication number E178E Date of Issue 06/06
Basic Setting Instructions for IQ and IQT Actuators
5
Basic Setting Instructions — Old (non-textual) Display
POSITION
DISPLAY
CLOSED
When using the setting tool
press key until display changes
PASSWORD
DISPLAY
OTHER ACTUATOR
SETTINGS
Site configuration of indication and control
options (see Publication E170E)
VALVE CONTROL
DISPLAY
CI (DIRECTION TO CLOSE)
TRAVEL
LIMITS
C3 (OPEN ACTION)
C2 (CLOSE ACTION)
or
or
Clock
Anti Clock
Limit
Display required option, press
or
Torque
to set. Option flashes when entered.
Limit
tO (TORQUE VALUE OPENING)
tC (TORQUE VALUE CLOSING)
or
or
or
or
or
40% to 99% or rated (100%)
Rated
40% to 99% or rated (100%)
Rated
Display required option, press
to set. Value flashes when entered.
Manually operate the actuator to the fully closed position
and back-off half to one turn of the actuator output.
Initial actuator settings are now complete and
it is possible to operate the actuator electrically.
Boost
LO (LIMIT OPEN)
When the
POSITION
DISPLAY
TORQUE AND POSITION
Bar indicators appear confirming that setting mode has been entered. If bar indicators
are not displayed, the actuator is in checking mode and settings cannot be changed.
LC (LIMIT CLOSED)
OPEN
(00 to 99)
Default password is I d - do not change
TORQUE VALUE
DISPLAYS
MID TRAVEL
Switch on actuator power supply - select
Local control. Setting may take place with
display indicating closed, mid travel or open.
Display will not indicate true position until
position limit settings have been completed.
Manually operate the actuator to the fully open position
and back-off half to one turn of the actuator output.
is pressed the bars will flash and the appropriate indicator lamp will be illuminated.
It is possible to return to the position display from anywhere in
the setting procedure by pressing
and
together.
Torque
Basic Setting Instructions for IQ and IQT Actuators
Basic Setting Instructions — New Pro Display
POSITION
DISPLAY
6
Closed Limit
Switch on actuator power supply - select
Local control. Setting may take place with
display indicating closed, mid travel or open.
Display will not indicate true position until
position limit settings have been completed.
CLOSED
MID TRAVEL
OPEN
TORQUE AND POSITION
Closed Limit
Stopped
Open Limit
Torque = 19%
PASSWORD
DISPLAY
When using the setting tool
press key until display changes
(00 to 99)
Enter Password
ID Hex
Enter Password
Password Correct
Bar indicators appear confirming that setting mode has been entered. If bar indicators
are not displayed, the actuator is in checking mode and settings cannot be changed.
TORQUE VALUE
DISPLAYS
VALVE CONTROL
DISPLAY
OTHER ACTUATOR
SETTINGS
Default password is I d - do not change
Site configuration of indication and control
options (see Publication E170E)
Basic Setup
Config Setup
CI (DIRECTION TO CLOSE)
Close Direction
Clockwise
Close Direction
Clockwise
Close Action
Close on Limit
Close Direction
Anticlockwise
or
Clock
Anti Clock
To Set
Limit
or
Close Torque
99%
or
40% to 99% or rated (100%)
TRAVEL
LIMITS
Set Close Limit
Move to Close
Set Close Limit
Move to Close
Open Torque
40%
Close Torque
100%
Rated
To Set
POSITION
DISPLAY
Open Action
Open on Limit
Torque
To Set
or
Limit
Open Action
Open on Torque
Torque
To Set
Open Torque
99%
or
40% to 99% or rated (100%)
Manually operate the actuator to the fully closed position
and back-off half to one turn of the actuator output.
Initial actuator settings are now complete andit
is possible to operate the actuator electrically.
or
Open Torque
100%
Rated
or
Open Torque
Boost
Boost
To Set
LO (LIMIT OPEN)
When the
Open Limit
Close Action
Close on Torque
tO (TORQUE VALUE OPENING)
LC (LIMIT CLOSED)
or
tC (TORQUE VALUE CLOSING)
Close Torque
40%
C3 (OPEN ACTION)
C2 (CLOSE ACTION)
Set Open Limit
Move to Open
Manually operate the actuator to the fully open position
and back-off half to one turn of the actuator output.
To Set
is pressed the bars will flash and the appropriate indicator lamp will be illuminated.
It is possible to return to the position display from anywhere in
the setting procedure by pressing
and
together.
To Set
Basic Setting Instructions for IQ and IQT Actuators
8
Check List — Old (non-textual) Display
CHECK LIST
Check List — New Pro Display
7
CHECK LIST
Checking actuator settings requires the use of
and
keys only. Displays on actuator show set values.
Return to the start of the setting procedure (Position Display) by pressing
and
together.
Checking may be carried out with the actuator in either Setting or Checking mode.
Until C1 (DIRECTION TO CLOSE)
is displayed
Checking actuator settings requires the use of
and
keys only. Displays on actuator show set values.
Return to the start of the setting procedure (Position Display) by pressing
and
together.
Checking may be carried out with the actuator in either Setting or Checking mode.
Until C1 (DIRECTION TO CLOSE)
R
is displayed
Clock
Anti-clock
To display C2 (CLOSE ACTION)
O T O R K
Clock
B A S I C
To display C2 (CLOSE ACTION)
Limit
To display C3 (OPEN ACTION)
Limit
RCloseA
N G E
Direction
Anticlockwise
Anti-clock
S E T T I N G
Close Action
Close on Limit
Close Action
Close on Torque
Limit
Torque
Open Action
Open on Limit
Open Action
Open on Torque
Limit
Torque
I N S T R U C T I O N S
Torque
To display C3 (OPEN ACTION)
Close Direction
Clockwise
Actuator Indicator Display Window
Torque
To display t C
(TORQUE VALUE CLOSING)
Display shows
selected torque
To display t C
(TORQUE VALUE CLOSING)
To display t O
(TORQUE VALUE OPENING)
Display shows
selected torque
To display t O
(TORQUE VALUE OPENING)
Close Torque
40%
Display shows
selected torque
e.g. 40%
Hold setting
tool directly
Display
showsin front
of indicator window.
selected
torque
OpenRange
Torque
0.5 metres (18
inches)
40%
e.g. 40%
Across Key
Press
and
together to return to Position Display and move valve to fully closed
condition checking that closed symbol and lamp appear just as the limit of travel is
reached.
Press
and
together to return to Position Display and move valve to fully closed
condition checking that closed symbol and lamp appear just as the limit of travel
is Key
Plus
reached.
Move valve to fully open position checking that open symbol and lamp appear just
as the limit of travel is reached.
Move valve to fully open position checking that open symbol and lamp appear just
as the limit of travel is reached.
UK Head Office
UK head office
USA Head Office
USA head office
RotorkInc
Controls Inc
Rotork Controls
telephone
(585) 247Blvd
2304
675Rochester
Mile Crossing
telefax (585) 247
2308
Rochester
email info@rotork.com
Red Local / Stop / Remote Selector.
As part of a process of on-going
Select to “Local”
product
development, Rotork reserves the right
to amend and change specifications
Down Key
without prior notice.
Rotork Controls Rotork
Limited
Controls Limited
telephone Bath 01225 733200
Brassmill Lane
telefax 01225 333467
Rotork Controls Inc, Rochester, USA
Bath BA1 3JQ
Published data may
be subject
Minus
Key to change.
Rotork Controls Ltd, Bath, UK
email mail@rotork.co.uk
NY 14624 USA
England
For the very latest version release, visit
our website at www.rotork.com
A full listing
of our
worldwide
on our website at www.rotork.com
Tel:is+1available
585 328 1550
Enter Key
Tel: +44
(0) 1225
733200sales and service network
Fax:
+1
585
328
5848
Fax:
+44
(0)
1225
333467
Email: info@rotork.com
Email: mail@rotork.co.uk
These instructions enable the actuator to be configured to suit
Setting Tool
The name Rotork is a registered trademark.
Rotork recognizes all registered trademarks.
Published and produced in the UK by
Rotork Controls Limited.
POWTG0306