April - The Recreational Aircraft Association

Transcription

Recreational Aircraft Association Canada www.raa.ca
The Voice of Canadian Amateur Aircraft Builders $6.95
March - April 2012
From The
President’s Desk
Gary Wolf
FIRST FLIGHT PREP
This is the time when builders have
had their final inspections and are
ready to do their first flights. This
frequently means that the builder
has been devoting all of his time and
money to completing the plane and
has not flown in a couple of years. In
this country a license can be kept valid
by sitting in 2 hour TC seminar every
two years and being PIC once every
five years. Vanity and finances can
combine to have a rusty pilot in the
pilot seat of an untested airplane. The
first flight regs require that a pilot have
a minimum of 100 hours in a plane of
the appropriate category but that does
not mean the same make and model.
In most cases it means single engine
non high performance landplane, and
it does not take into account whether
the plane is nose- or tail-dragger. One
hundred hours as PIC in a Cessna 150
“qualifies” the pilot to do the test flight
in a Harmon Rocket taildragger, but
not in the real world.
Find someone in your chapter
who is current and has enough experience in the same type or similar aircraft. Have the final inspection done
at an airport with a long runway that
is into the prevailing wind, has clear
approaches, and is surrounded by flat
fields in case of an engine-out during
the first climb. Tie the tail to a post and
run the engine at full throttle for an
hour or so the check all engine paramThe Recreational Aircraft
Association Canada
Waterloo Airport, Breslau ON
N0B 1M0
Telephone: 519-648-3030
Member's Toll Free line: 1-800-387-1028
email: raa@raa.ca web: www.raa.ca
eters. When everything looks OK and
the day is right do not invite an audience. If something does not feel exactly
right, there should not be the pressure of disappointing the crowd. The
show can go on some other time when
everything is right.
CADORS
The Cadors are the daily occurrence
reports of everything that has been
observed or reported about Canadian
aircraft, Canadian airspace and aerodromes. These reports are published
online daily. Just google for “cadors”
and choose the daily report and you
will get about 100 reports each day. Or
you can go to the word/text option and
select your keywords and time period.
I usually select “narrative” and search
for “amateur ultra ultralight sailplane
hang glider” and then select “any of
these words” in the menu below. That
gets most of the non certified reports
for the chosen time period. Sometimes
the TC personnel forget to say in the
narrative how the plane is registered
so I do a subsequent search using “private” as the keyword. This is a much
looser search but there are inevitably
some pertinent reports that were not
included in the initial search. Registration letters are not given for privately
owned aircraft.
The early season usually has a lot
of reports of poor flying practices, and
the good weather in March meant that
this began early. There has already
been an ultralight trike fatality near
The Recreational Flyer is published
bi-monthly by the Recreational Aircraft
Association Publishing Company, Waterloo
Airport, Breslau, ON N0B 1M0. The
Recreational Flyer is devoted to the aerospace
sciences. The intention of the magazine is to
promote education and safety through its
Sherbrooke Quebec, and in Ontario
someone in a single seat wood and
fabric plane decided to land at YYZ
Pearson airport. As he taxied in he
held up an Air India 777 and caused
a KLM 747 to do a go around. If it had
been a Mayday and he was on fire, the
pilot was correct to fly into Pearson.
Otherwise this might be the pilot’s last
logbook entry.
GYRO TRAINING EXPANDS
For many years there has been no
training unit in Canada for the gyroplane license so very few have been
built, a shame because they are very
nice aircraft that are not expensive to
build, and they need very little space
for hangaring.
In Quebec Nicolas Horn has been
providing training in a Magni gyro
and his new training unit is in Lachute
Quebec. www.magnigyro-canada.com
In Ontario there will soon be a
training unit at Waterloo Regional
airport CYKF. Neil Laubach has 1500
hours in rotary wing aircraft and will
be opening the school mid summer
2012. 519-573-0066 www.gyroontario.
ca
Take the opportunity to get some
seat time in one of these aircraft and
you might then consider building
a gyro. If so, we have a chapter in
Toronto that is devoted to these unique
aircraft. Contact Jerry Forest at gyro_
jerry@hotmail.com .
The season is finally here – let’s all
enjoy it and fly safely.
members to the general public. Opinions
expressed in articles and letters do not
necessarily reflect those of the Recreational
Aircraft Association Canada. Accuracy
of the material presented is solely the
responsibility of the author or contributor.
features
Gone South
Raymond Firer's adventures with the South African Air Force................................................................... 4
Motivation
Mike Shave makes skis for his Druine Turbulent..................................................................................... 10
When Do You Say No?
Barry Meek about making right choices................................................................................................. 12
Rotax 912iS
Clare Snyder goes to Austria to preview the latest in aero motors........................................................... 17
Catching A Good Virus
Reinhold Dresler's composite beauty: slow, fast, and drop dead gorgeous.............................................. 22
columns
From the President's Desk / by Gary Wolf.......................................................................2
Across Canada: Chapters in Action...............................................................................19
Technical, Safety, and Stuff
Innovations: 3 revolutionary aircraft mature.......................................................28
Product Review: Drill Doctor...............................................................................29
Denso Iridium IK24 C11 Spark Plug Failures........................................................30
Portable Power / Terry Jantzi..............................................................................32
George Gregory
Classified.....................................................................................................................38
A Tiger Moth sits out the haze. Goderich, 2005.
On the cover: The Pipistrel Virus, photo courtesy
Pipistrel Canada
Gone South
Flying with 41 Squadron, South African Air Force / by Raymond Firer
M
y interest in flying goes back to my late childhood, as
I suspect, it does for most of you. My heroes were the likes
of RAF aces Douglas Bader, Bob Tuck and Sailor Malan,
amongst others. But first, a little geography, so that you can
understand where I came from.
I was born, and lived most of my life, in what is known as the Cape
Peninsula (see page 6) with Cape Town at the Northern end facing an
open bay known as Table Bay. The small airfield I began flying from, called
Youngsfield, is situated about two-thirds of the way to False Bay, SouthSouth East of Table Bay, and just South of Ottery Road. False Bay is the
large bay to the South of the land connecting the Peninsula to the mainland.
The picture on page 6 also gives some indication of the mountainous
Peninsula with the flat land connecting it to the mainland. Called “Cape
Flats”, it is close to sea level. Cape Town International Airport, situated on
the Cape Flats, is only one hundred and fifty feet above sea level.
Cape Town is famous for the mountain which backs it to the South of
the city. Called Table Mountain for obvious reasons, it rises to 3600 ft at
the Western end (page 7), featuring a sheer drop down the front from the
summit.
I began assembling plastic model aircraft, mostly of the World War 2
vintage, although I did scratch build a model of the Avro Arrow, until, as a
teenager, I had a collection of about 120 models hanging from the ceiling of
my bedroom. When the South East wind blew, as it did so often in Summer,
my mom said that it looked like the Battle of Britain. However I never
mastered the craft of building flying models. My one and only attempt
ended in flames, literally. It was a model of a Piper Cub (J3C) and looked
quite good but on its first flight it spiraled into the ground, causing a fair
amount of damage. That was when a paint thinner soaked rag was added,
set alight, and the poor little aircraft was sent to its doom.
Thoughts of actually flying didn't enter my head except in my dreams,
as my parents certainly couldn't afford flying lesson, and I was too occupied with school and sport to find work to finance that dream myself.
4 Recreational Flyer
March - April 2012
Top left: a topographical map of the region, showing the quite mountainous Eastern and Southern rim, with a high plateau in the center. This plateau is about 4000 ft above sea level.
Top right: South Africa is bordered by Namibia, Botswana, Zimbabwe, Swaziland and Mozambique, with with Lesotho enclosed within the Republic. You can see Cape Town, Johannesburg, Petersburg,
Ladysmith and Mafikeng, all of which feature in the story. Missing is Potchefstroom, situated between Klerksdorp and Krugresdorp, and is also important to the tale. Below: Cape Town and its environs.
On graduating high school, I was drafted into military service, as were all white males in South Africa at
that time, and the Infantry was to be my calling for the
next year. After basic training, we were asked to volunteer for special force training of our choice. I opted for
Paratroopers, only to be informed that for our intake
there wouldn't be a Parabat course. I was offered the next
best option, officer training, and this turned out to be the
best thing for my flying ambitions.
I passed the Officer course at the top of my class, and
was sent to 5 SA Infantry Battalion, in Ladysmith, Natal,
where I served out my final three months. Towards the
end of this time, volunteers for flying training were
called for from among the officers, as all pilots in the
South African forces at that time had to be commissioned
officers. I jumped at the chance, and after undergoing
an extensive, three day medical test, I was told that I
would be contacted in due course, if I had been accepted
for flying training. Soon after that I returned to civilian
life, and began my first job with the Weather Bureau. After an initial period at the head office, I was sent to a
small weather station in the Northern Transvaal town of
Pietersburg, on an airfield used, in part, by the military. It
was here that I had my first flight.
As a sideline, I would moonlight by refueling any
light aircraft in need of that service, and on a quiet
Sunday afternoon, a Tiger Moth landed, taxied in, and
asked for fuel. After topping up his tanks, the pilot asked
if I would like to take a short flight with him. Would
I indeed! I jumped at the chance, and we were soon
airborne. I don't remember too much of that first time in
the air, except wondering why the pilot had a parachute,
March - April 2012
Recreational Flyer 5
A eastward-looking depiction of the mountainous Peninsula
with the flat land connecting it to the mainland. Called “the
Cape Flats”, it is close to sea level. Cape Town International
Airport, situated on the Cape Flats, is only one hundred and
fifty feet above sea level. Below: the author, intreped pilot of
41 Squadron
and I didn't.
All too soon we were back on the
ground, and it was several months
before I received instructions to
report for flying training at a local
aero club in Cape Town. I immediately applied for a transfer with the
Weather Bureau, and three months
later, I found myself, at 6:30 on a cold
and rainy Autumn morning, at the
Cape Aero Club, housed on a military
airfield called Youngsfield, an all grass
field without runways, a vintage of
the second World War. Youngsfield
was also the home of the SA Defense
Force's training unit for anti-aircraft
gunners. But more of them later.
After being issued with a log
book, I was taken out to the hard
stand where a lone Cub stood in the
driving rain. I was sure that the flight
couldn't take place in that weather
but I was wrong. Taking off into that
heavy rain, it sounded as if we were
under machine gun attack. I couldn't
see anything forward but the halfhour flight was exciting if uneventful,
and after a short debriefing in the
clubhouse, and a cup of coffee, I was
off to my day job.
That was the beginning of many
early morning and weekend ses6 Recreational Flyer
sions, until, at about eight hours
I went solo. What a thrill being in
complete control of the aeroplane!
The usual one circuit and a landing,
and it was all over but it was exciting,
and I felt very proud of myself. Then
followed the usual training. Circuits
and bumps. Oh so many circuits and
bumps. Cross-wind landings, stalls,
spins, forced landings and lots of low
flying, and all the theoretical subjects
too. At 30 hours I successfully completed the flying and theoretical tests,
conducted by an Air Force instructor,
and gained a Private Pilot's Licence.
This PPL was essential as I was actually flying civilian aircraft in what was
civilian airspace but now I could take
passenger on some of my flights, and
several of my friends were the happy
recipients of this privilege. At least, I
assumed that they were happy about
it. There had to be a little wangling to
allow me to take passengers, as the
Club was being paid by the Army, so
if I wanted to take a passenger on a
particular day, I would book the flight
as a private one until I returned safely,
then transfer it to the military log.
As I was being trained for the
Army Air Reconnaissance squadron,
there was lots of low level flying,
and the section of the general flying
area designated for this task was
just inland of the sea, and consisted
of overgrown sand dunes lying in
closely serried rows. I loved flying
over these dunes, dipping and climbing to maintain between100 to 200ft
AGL. Later, I would apply this training to hopping over the waves just
off the beach, sometimes returning
to the airfield with salt spray on the
windshield.
Soon I graduated to the Piper
Cruiser (PA12.), and I loved the way
this aircraft did a spin. Really nose
down. You would be hanging in the
straps looking at the Earth whirling
round, and I now began navigation
training. After a few dual attempts, I
was sent off on my own for the first
time. And good news, I made it safely
back home. Doing these two or three
hour journeys at 200ft was even more
thrilling. This was flying. Watching
the ground flash by under the aircraft,
until it was time to climb to circuit
height and a landing. Often I would
plot the return leg along the coast.
March - April 2012
Cape Town is famous for the mountain which backs it to the South of the city.
Called Table Mountain for obvious reasons, it rises to 3600 ft at the Western end.
That way I could spend the best part
of an hour skimming the waves,
watching the seemingly endless
beach flash by on my left.
Navigation in the Cape was a
breeze. With the sea on the Port side
heading North, and the Mountains
off the Starboard wing tip, who could
get lost? And the famous landmark
of Table Mountain could be seen
from many, many kilometers out. As
I progressed, I began to explore a bit
more. One of my favorite early morning flights being a tour round the
Peninsula, and returning up the back
of the famous Table Mountain. At it's
highest point Table Mountain is about
3600ft. And I would climb steadily up
the back, maintaining 50 or 60ft above
the rocky ground, heading North to
the front edge of the massive. Shooting over the edge, the 3000ft almost
sheer drop was spectacular and
thrilling, and once over the edge, I
March - April 2012
was well above the regulation 2000ft
above the city.
Training continued fairly
uneventfully, with testing by Air
Force officers at 50, 75 , and finally
100 hours, then I was on my way
to 42 squadron (Training Flight) at
Potchefstroom, in the Transvaal, for
the Wings course. Potchefstroom,
situated at about 4000 ft above sea
level, had dirt runways; 03/21 and
33/15, and was on a slight incline
on both of these main headings, or
downhill on the reciprocals, and was
the also the home of the Army's gunnery school. There I met three other
student pilots who had undergone
similar training in other centers. We
four were the full intake of pilots for
this new Army venture to reinstate
the air reconnaissance branch of this
service. Both 41 and 42 squadrons
were started at the beginning of WW2
but were disbanded in 1944.
I don't remember
too much of that
first time in the air,
except wondering
why the pilot
had a parachute,
and I didn't.
At the end of the runway,
he would flick to right way
up, pull up into a stall turn,
and land. He had done this
countless times, only this
time he didn’t make it
The day before we arrived at Potchefstroom, there
had been an accident. The chief flying instructor of the
Air Force had crashed on the runway, in front of several
student pilots, three of whom were in the circuit on their
first solo. The CFI, flying a Harvard, indicated to the
tower that he would be doing a “stealth” approach. This
involved coming in over the runway at very low altitude,
inverted, with the magnetos off to cut the engine noise. At
the end of the runway, he would flick to right way up, pull
up into a stall turn, and land. He had done this countless
times, only this time he didn’t make it, and pancaked onto
the edge of the runway. He was killed instantly. So much
for the safety, safety, safety we had had drilled into us. The
poor solo guys were then diverted to a cross wind runway
for their landing! Fortunately nothing else untoward happened.
We were introduced to our instructors, who acquainted
us with the Cessna 185’s we would be flying. And so we
were off, once again being treated as pupil pilots until,
after about four hours, we were sent solo on this aircraft.
Then we began the more military side of the course.
All four of us did our first solo on the 185s on the same
day but for one guy, it was the end of his training. On
landing, he ground-looped, ending up on the nose. He
was unhurt but he jumped out, ran to his room, collected
his gear, and left for home, never to return. That aircraft
was repaired in just over a month but we always felt that
it seemed to want to fly in circles after that, and no one
wanted to use it.
We were expected to always fly on compass headings
in the circuit. This meant that often on the base leg, we
would drift well away from the runway, and had to power
in, always with full flaps and trimmed right back. Quiet a
battle. This became known as a “Boeing” approach.
We discovered that Military flying can be quite boring
at times, so we tried to liven things up by doing some
really low flying. It was, after all, our calling. We were
constantly reminded that our operating ceiling was 200ft
AGL. Nothing was said as to the lowest we were expected
to fly, and as we were operating over corn fields, we
would often come back with corn cobs in our wheels.
It became standard practice, after one of these hairy
escapades, to do a very short landing, hop out, clear the
wheels, before taxiing in to dispersal.
Left, above: a rough strip landing. Bottom, left to right: classmates John, George and Raymond
with a squadron aircraft
March - April 2012
The author during his tour of duty. He had originally selectedthe paratrooper corps, but with no
spots left, took officer training instead - which worked out quite well for his flying ambitions.
And speaking of low level
exploits, we had to practice concealed
approaches, dodging behind trees and
buildings, and dipping into dry river
beds, anything that would hide us
from the tower until the last moment,
when we would pop over the fence,
and a short landing.
Another fun exercise was flying
a figure eight at 200 feet over a cross
road, pulling max. rate turns, making
sure that we crossed exactly over the
intersection each time, and keeping
the ball centered. This was, in fact, to
be part of our wings test.
Right from the start of our training
on the 185s, it was drummed into us
that this aircraft was not in any way
aerobatic, although sometime later
I discovered that this was not true
but we weren't given any aerobatics
training. We were not even allowed
to do spins. We were expected to
practice incipient spins only. This
involved pulling the nose up under
cruising power until the aircraft was
almost ready to stall, then kicking the
rudder full over but as soon as the
wing began to dip, we would have
to recover. We discovered however,
that one or two of our aircraft just
wouldn't stall with so much power
on, so we would cut back on the throttle slightly to initiate the stall. Then I
discovered that at this point, with the
March - April 2012
rudder full over, and the stall warning blaring, if I closed the throttle
just a bit more but quite quickly, the
machine would flick on to its back.
The first time this happened it scared
the hell out of me, but I managed to
recover, and after trying this a few
times I realized that the “best”way
out of this inverted position was to
pull it through in a half loop. So this
became one of my favorite tricks. It
wasn't aerobatics, was it? I was just
recovering from an unusual attitude.
Speaking of unusual attitudes, for
our IF rating we had to do recoveries
from unusual attitudes. Practicing
under the hood, the instructor would
throw the aircraft all over the sky, and
when all the gyro instruments were
well and truly toppled, hand it over
to us, to get it back to straight and
level flight. Often they would try to
fool us, and leave the aeroplane in
straight and level but with instrument
lag, we would imagine that we were
nose down, or slipping sideways,
or inverted, and try to correct that
attitude with rather bad results. We
soon twigged on to this trick, and
simply waited until the instruments
had settled down, and gave us more
accurate readings, before trying to
make it to that calm flight pattern.
As we became more proficient at
instrument flying, we had to do cross
country trips under the hood. There
was even one time, on returning to
the airfield, that I was talked down
right onto the runway completely
blind. Obviously I had an instructor with me, so I guess that he must
have had at least some confidence in
my flying skills. Building up actual
IF time was a problem, as this part of
South Africa didn't get too much in
the way of clouds at that time of year,
just some scattered cumulus in the
mid afternoon. When these appeared,
we would rush to the aircraft, take
off, and make a mad dash for these
tiny patches of fluffy vapor, logging
as little as one minute at a time but
dodging through them several times
before they dissipated or drifted out
of our general flying area.
I found that navigating in the
Transvaal was far more of a problem
for me than in the Cape. The Transvaal is fairly flat and featureless, and
the first time I did a low level cross
country flight I missed the first turn
completely. I know that, as pilots, we
were never “lost”. We might be uncertain of our position but never lost.
Well that day I was VERY uncertain of
my position. The turning point should
have been easy to spot, a rail line, a
road and a small air strip, and if I had
been doing some dead reckoning, I
should have picked up that I was well
past that point some time back. But
I soon passed several similar markers, until the instructor called my
attention to the fact that I had missed
the turn. Only then did I do some
calculating, and worked out how to
get back on track for the second leg of
the flight. All ended well enough, and
I returned to the airfield on time. After
that I kept a closer watch on where
I was. It was a good lesson. Only a
couple of years later did I, once again,
find myself in a similar position.
Tune in next issue for the conclusion!
Mo ti va tion
•
•
•
a motivating force, stimulus, or influence :
incentive, drive
My flying buddy Ed Connors was
the inspiration to start this project
and he helped me to understand
some of the dynamics of skis. I
appreciate his friendship and his
enthusiasm for flying. So it’s time to grab a brew and a pencil
and paper. To design a set of skis for
my little airplane it was necessary to
look at other planes on skis and try to
come up with a method for calculating
the area or footprint of each ski. Also
taken into consideration were other
sports or activities on the snow to get
an idea of pounds per square inch to
use for airplane skis. Using my own
weight (200#) I discovered that X/C
Skis are 2 psi, snowshoes about 1.5
psi. I decided to use 1 psi to absorb
my usual 2g landing load and give the
plane a chance to sit on top of lighter
density snow after it stopped moving. The weight of my Druine Turbulent
with full fuel, a toothbrush and me, is
650#. So I made each ski area about
325 square inches. A rectangle 8x48 is
384 sq-in. The front of the ski is out
of the snow so its area is not counted. The shape in the drawing is 375 sq-in
but the area at the front and where the
wheel is reduces that to about what we
need. The area distribution should
be about 60% in front of the axle. Not
counting the upturned area at the
front, the Homebrew skis have about
a 55:45 ratio of areas in relation to the
axle centerline. We share a wonderful hangar at
CPG7 with a concrete floor. Whatever
skis I made for the plane would need
to include some method of moving
the plane around once in the hangar. Sometimes I buy “good deals” at Princess Auto for a future project. Tucked
in one of the joists in the basement
were a pair of heavy duty roller-blade
style wheels 4” in diameter by 1-1/2”
across with a 5/16” hole through the
centre roller bearing. Perfect. I also
had a sheet of 3/8” birch ply 63” x 30”
. All the parts are shown on the layout
drawing. To work out the geometry of the
parts I like to use card stock or paper
to make full size patterns. Once your
patterns have been cut out use them
to maximize the use of the plywood. Grain direction is important for
all wood projects and 3/8” x 5 ply
birch is very strong. Cut out all the
parts, radius the edges where needed
with a router, and sand, I used titebond waterproof glue for initial assembly. Later, epoxy and glass cloth will
be applied over the joints. Stainless
steel #6 x 3/8 flat head screws were
used to assist clamping during the
glue-up. Some screws were removed
after the glue set up. Cut out the
hole for the wheel and check the best
March - April 2012
Drawings of Mike's Skis.
height of the axle hole before gluing
the assembly together. I used some
offcuts of the 3/8” ply to set the depth
of the wheel below the bottom of the
ski. Once this is worked out pre-drill
a smaller hole through all the pieces
that the axle for the small wheel goes
through. (ie 1/4”) Changing to the
main gear, if your gear leg is steel
tube like mine, create the 4 bushings
using the drawing as a guide. Use a
hole saw to drill the holes to accept
the bushings, again before glue up. I
made the width of the box the same
as the actual wheel so I could use
the same method to attach the ski. I
needed to remove the brake assembly
because skis don’t use brakes. :) Fabrication
My portable Makita skill saw
makes a narrow kerf, ideal for the cuts
necessary to make the front end bend
up. The cuts are made leaving a 1/16"
of wood on the outside of the bend. Boiling hot water will help the wood
soften and the gorilla glue will work
better if the wood is damp. Screws will
hold the wood in position until the
glue sets. Start with aligning the centre
strip down the middle of each ski
shaped to fit the arc at the front. These
March - April 2012
are cut out over the centre where the
wheel is located. Add the two curved
side strips and temporarily screw them
into the centre strip. I used one layer of
1.5mm ply cut to fit over the saw cuts
in the area of the bend. Apply Gorilla glue and lots of clamps. I find this glue
works well in filling large gaps as it
expands as it cures. Let that assembly
dry overnight. The aft end of the ski is
shaped to allow 2 layers of 1/8" ply to
be glued on to form an upward bend. This treatment allows the plane to be
dragged backwards without the skis
digging in.
The next hurdle is assembling the
boxes to the skis. Do as much dry fitting as possible to ensure all the parts
line up. I used a short bit of tubing
and washers with 1/4” threaded rod
to block the distance for the small
castor wheel, and a 12” length of steel
tube through the main gear leg axle
bushings. Pre-drill any screw holes
and make alignment marks on the
wood. Once satisfied, apply the glue
and fasten the parts together using
temporary screws to hold the parts
in alignment, and bar clamps where
possible. The over-all ski assembly is
now complete.
The next step after this has set up
is to bond the whole thing together
with fibreglas and epoxy. I started
by laying in a fillet of epoxy and
micro balloons along the outside joint
between the top surface of the ski and
the 1-1/2” uprights. The radius of
a popsicle stick is a bit too small so
I make one with 1/4” radius out of
some 1/16” plywood. When this has
cured, sand out the lumps and lay in
two layers of 6 oz glass cloth about 2”
wide along the length of the joint. Lay
two 3” wide strips of fabric centred in
the trough lapping up the inside of the
uprights. (You may want to remove
some or all of the screws used here
during the initial glue up.) Some folks
like to use a peel ply of rayon fabric
and some like to use polyethylene
over the resin as it cures. Or nothing.
I like to work with this stuff in steps
so while that is curing I cut the pieces
that will fit over the tapered box in
the middle. Allow some overlap at the
corners. Peel ply does work well here
to hold all the cloth bits in place while
you smooth the resin, so you can cut
those shapes as well. I used two layers
of glass cloth over this assembly as
well. As a note: polyester resin does
not stick as well to wood as epoxy
does. Recreational Flyer 11
When it is set up
remove the peel ply
and admire your work
! Clean out the area
where the bushings
attach and drill holes
for #6 x 3/4" SS flat
head screws. Mix up
some bedding compound using epoxy
and cabosil or talc (synthethic sawdust) You
should have marked
the bushings for the
hole they fit and orientation. Smear some
goop where the bushAll the wooden parts can be cut out of a single sheet of Birch Plywood.
ing will mate with the
box. The inside of the
bushing will be greased so epoxy will not stick as you
slide the dummy 12" axle tube into place. Snug up the
screws. Let this assembly cure.
Next step is glassing the bottom. Here I used a single
layer of glass cloth with epoxy. A peel ply is nice to use
here. When this is cured use a smooth file to touch up
any sharp glass edges. Tighten up the SS Screws.
I am useless with paint. Here you are on your
own. I ended up using an exterior latex paint but the
best choice would be an epoxy based paint.
Last steps are fitting a layer of lexan to the bottom
of the ski and installing the castor wheel. Again I had
some left over lexan from a windshield job. I think
it was .090”. I’m sure 1/16” would work as well. Installation is straightforward.
The lexan was attached with 10 off SS #6 x 3/8 flat
head screws spaced along the bottom in line with the
uprights.
Rigging skis for a taildragger (verify this method
with someone you know and trust)
Having the nose of the ski tip downward in flight
would be a bad thing. I worried about this problem
with respect to the security of the fittings especially
into wood. My experience after flying with skis is
that this kind of event is unlikely. The ski “flies” and
seems to give the plane a bit more buoyancy in the
air. There is more area in front of the pivot of the ski,
providing more lift than the aft portion of the ski. This
effect along with the safety of the cable rigging and
the bungee pulling will make the tipping of the tip
downward unlikely. Snow load on the forward part of
the ski will add some weight but during take-off most
of that snow blows off. There is less drag with the skis
March - April 2012
as well. Nevertheless, making the attachments between
the ski and the plane needs to be done with confidence in
the design. Block the aircraft off the floor so the gear legs
are extended. Block the front of the skis 3” with the tail of
the skis touching the floor. Raise the tail of the plane to the
angle it flies at in cruise. Set the length of the rear wires. After the wires are installed lift the tail to watch them
get tight at this angle of attack. Set the tail on the floor. Remove the blocks at the front and place a single 2x4 on the
flat at the tail of the ski with the forward arc of the ski tips
touching the floor. Set the length of the front wires. Raise
the tail and this wire will go slack. With the tail raised,
attach the bungee to the front with some degree of tension. It will get longer as you lower the tail but you want it to
have some pulling power even in the raised tail position. For attaching the wires to the ski I used AN4 bolts, lock
nuts and washers through one of the uprights and the cable
thimble without over-tightening the bolt and nut assembly.
For the tail ski I used 12” of plastic deck post cut so that
it looked like an inverted U. See the drawing. Use a heat
gun to form the front bend. Fasten to a 12” long 2x4 as
shaped in the drawing and install in place of the tailwheel. The downturned edges of the tailski provide a bit of purchase in the snow for turning.
Testing:
For those of us who have not had fun flying with skies
here are a few observations:
1. no brakes 2. they stick when stopped and take full power to get
moving. refer to #1 3. skis are quiet when there is enough snow 4. skis are really bumpy when taxiing on frosted grass. 5. take-off is shorter 6. acceleration better 7. steering is interesting. See #1 8. Have fun !
Bushcaddy still flying high
Bushcaddy, Quebec's own brand of rugged
Bush plane and their kit manufacturer are
doing well; under new ownership and
in the new location at the Lachute
airport since September 2010 they have
continued to see growth and optimism in
the world economy.
Tony Watkin moved himself to Quebec
from Australia after he acquired the
business in 2010 to ensure the brand
remained where it had been born 18 years
earlier and he has remained in Lachute,
March - April 2012
now calling it home. The range has
continued to develop, and with access to
more technology at Lachute the kits are
becoming more assembly friendly, and
with more CNC parts available the finish is
becoming more consistent and assembly
has become a simpler process for the
builders.
Over the past 18 months Tony has
developed several improvements such
as full pre-drilled and pre-cut ailerons
and flaps, the R80 has pre-drilled wing
skins and the flap option is now more of a
standard with builders due to the ease of
installation. Demand for the aircraft and
kits is spreading with sales to Australia
and Russia, as well as many inquiries from
Asia which is a new market due to China
opening the skies to private recreational
aviation for the first time in history.
The future will see the further development
of the current models as well as some new
models still in concept stage and will offer
buyers a broader range and choice, but in
Bushcaddy style they will try to keep the
mechanics of the range simple, effective
and robust as well as keeping many parts
standard among the models. This keeps
overheads and prices low to ensure that
they are remaining competitive on the
world market.
The short term goal is to establish a small
dealer network which will assist in growth
as well as making delivery of kits and
parts more efficient. Tony looks forward
to the future and is extremely proud to be
associated with such a well known bush
plane and is confident the aircraft has
many years ahead.
When Do You Say No?
Barry Meek
Continuing VFR into IMC. We
read that short statement in aircraft
accident reports far too often. And by
now you'd think pilots would know
better. You don't fly, in fact you can't
fly visually in instrument meteorological conditions. It's a simple
fact. So why then, does it continue
to happen and cause crashes? Why
are people dying and perfectly good
airplanes being wrecked by pilots
trying to beat the unbeatable odds?
These are accidents that don't
need to happen. They're predictable, and therefore avoidable. It' s all
about decision making. When to say,
"No, I won' t fly into that area, those
clouds, that weather" . Let me try to
sort this out.
A young pilot with a brand
new license in his pocket will often
turn back from bad weather sooner
than a more experienced one. At
this point in his career, that good
decision usually has nothing to do
with good judgment, but rather
fear. He is afraid of cloud because in
his relatively short time flying, he's
been in nothing but clear conditions,
supervised by his instructor. Weather
distractions are usually not a factor
in the learning environment. His
low-time is an advantage, and may
save his life more often than he could
possibly know.
Now put that same pilot in a
similar situation after he's built up
four or five hundred hours working
in a small charter operation. By this
point in time, he has no doubt flown
in a bit of 'soup' , but has made it
through without too much trouble.
Chalk up the good outcome from
each of those flights to good experience. His confidence is increased as
long as he's not hurt. It's an important, necessary process. The weather
doesn't accommodate pilots or air
operators with clear, VFR conditions
all the time. Some calculated risks
and bending of the rules are a fact
of life. The pilot gains experience
March - April 2012
quickly, but unfortunately it usually
happens too fast, and his age, maturity and good judgment lag behind.
This is not a good thing. This is
when he becomes dangerous to himself, his airplane, employer and his
passengers. The pilot at this stage,
has beaten the weather enough times
to figure out the risks have rewards.
So he continues to take them. Every
one of us has flown into and through
something that we know we should
not have been in. We do that because
there are usually good 'reasons' for
continuing on into deteriorating
conditions. We push ourselves to
complete a flight because of pressures of the job or from passengers
on board.
Someone once described a good
pilot as one who relies on his excellent judgment to avoid the situations
which require his exceptional skills
to get out of. A true statement if I
ever heard one!
Clear judgment must be accom-
March - April 2012
panied by the courage to make the
right decisions too. A pilot may
judge a situation to be unsafe, but
without the courage to say "no"
to his passengers or employer,
he remains a reckless risk. Both
judgment and courage come with
experience, and with age. I've always
believed that the older the pilot, the
safer he will be. Of course that comes
with the caveat that there's a point
where the mind starts to slow down
and have trouble with solid reasoning too.
This is all philosophical ramblings from someone who thinks
he’s old enough to know better, and
not old enough to feel he's on the
downward slide. And when I was
younger, I probably thought I was
wiser too. But that really wasn' t so.
I'm a lot wiser now, and I have no
problem turning back from weather
or conditions that, years ago, I would
have proceeded into and may have
wound up in serious trouble. Luckily
it never happened, because undoubtedly there was some degree of good
judgment happening then too.
Looking at all the accidents that
result from the VFR flight into IMC
scenarios, I'm left wondering why
it happens so often? In my experience, the one (or two) times I flew
into bad weather, it scared the pants
off me. Although I made it through
in one piece, I wasn' t proud of it. In
fact I was mad at myself for getting
Clear judgment must be
accompanied by the courage to
make the right decisions
As time passes
you begin to
realize how soon
these trips... were
actually of no real
importance once
some time has
passed.
into something I knew I should
not have. Then I resolved it would
never happen again. And it didn't.
Apart from those incidents, there's
not been another decision I could
still not defend as being the right
one. That leaves me out of a lot of
hangar discussions that evolve into
bragging and boasting about how
bad the conditions were, and how
the storyteller made it through.
They're all interesting, some embellished almost beyond belief, but
that' s OK . Some people are just
plain lucky. They say they've made
it through time after time in conditions they describe as something
of a nightmare to me. "No thanks"
I say. I'll play it safe. My airplanes
have never been bent, and nobody
ever got hurt. You can' t argue with
decisions like that.
I'm giving the final word on this
topic to someone on the AVCANADA internet forum. I am not a
member of the group that writes
in the forum, so I know nothing of
this person’s background or experience. But his words of wisdom say
it well. Quote: " This is part of the
learning process, as time passes
you begin to realize how soon
these trips we thought just had to
go regardless, were actually of no
real importance once some time has
passed."
After over a half a century of
flying I can not remember even
one trip that I refused to do that
resulted in someone getting killed
because of my decision not to fly.
Barry Meek at bcflyer@hotmail.com
March - April 2012
Rotax 912iS
Clare Snyder reports on the latest offering from Rotax
The Rotax 912iS is a development
of the current 912 series. Internally,
the manufacturer has modified the
cylinder heads for better cooling, and
installed a larger oil pump. It is 4Kg
heavier than the 912S, not counting
the dual fuel pumps.
Carburetors have been replaced
by an injection system that runs at 3
bar pressure and is fully redundant
with 2 injectors per cylinder. It uses
MAP sensors and throttle position to
select full power or eco mode (mapping), and if one injector malfunctions it will switch to full fueling from
one injector instead of split fueling.
The engine uses four EGT sensors
and is designed for MON85 / RON95
octane fuel with an antiknock index
of 91.
The engine
management
system is by Rockwell Collins. It uses the CAN Aero bus for communication and diagnostics, with the pilot mode diagnos-
March - April 2012
tic program capable of displaying all
diagnostics and instrumentation on
a laptop. The system has full electronic ignition timing, and the next
software version will implement the
knock sensor for octane correction.
The new engine uses dual flywheel alternators with a total combined output of 430 watts. The engine
starts on battery, and then switches
over to the 16 amp alternator, running
independently of the battery system in case of alternator failure the system
switches back to the battery. The rest
of a plane’s electric requirements and
battery charging are handled by the
30 amp alternator.
Reported fuel burn is 21% lower
than the existing 912S. Peak torque
is apparently slightly lower but at
a higher rpm, so peak horsepower
remains 100 at 5800 rpms for 5 minutes. The engine may be operated on
leaded or unleaded mogas, 100LL,
and E10 fuel. Rotax has positioned
this engine as being the green solution for future aircraft, and even the
valve covers are painted in this colour.
Rotax is partnering with Pipistrel as
the launch customer, to emphasize
the fuel economy and low environmental footprint of the 92iS.
Gone are the carburetors, replaced by injection and an
engine management system for improved fuel economy
and smoother operation. Below left, Clare Snyder checks
out the engine management system. Below right, a
techician on the Rotax assembly line.
The new engine case features a
higher flow oil pump, and a recontoured sump for more efficient oil
scavenging. Existing engine mounts
are compatible, and all existing configurations will be available (reduction ratios, CS support etc). TBO for
the new engine is 2000 hours. A 14
- 17% price premium is expected for
the new 912iS engine when it becomes
available in six months.
Developed and designed
on the basis of the concept
of the 912 S/ULS the new
Rotax 912 iS engine offers
all well known advantages
of the Rotax 4-stroke
engine series.
Keep in Touch With
Your Board of Directors!
Gary Wolf................................................................. President
......................................519-648-3030 garywolf@rogers.com
Wayne Hadath........................................................ Treasurer
............................................................ whadath@rogers.com
Dave King ............................................... kingdws@shaw.ca
Gerry Theroux ...............403-271-2410 grtheroux@shaw.ca
RAA Regional Directors
Manitoba:
Jill Oakes...............204-261-1007 jill_oakes@umanitoba ca
Mainland BC:
BC Coast . ......................................................John Macready
................................................................ jmacready@shaw.ca
Interior BC/Technical Director:....................... David King
contact best between noon-10pm 7days work
ph. 250-868-9108 homep ph. 250-868-9118...........................
.................................................emailKingDWS@Gmail.Com
Alberta North:
Pending
Alberta South:
Saskatchewan:
Laura Drinkwater............................................ 306. 955-1361
lauraprd@shaw.ca
Ontario SW:
Jim Tyler.............................................................. tyler@orc.ca
Quebec:.......................................................................Pending
Appointed Positions:
Translation:.................................................................Pending
Magazine Mailing:..............................................Dave Evans
Ultralights:..................................................................Wanted
Web Page...................................................... George Gregory
Insurance Committee........................................... Gary Wolf
AirWear...................................................................Dave King
March - April 2012
Across Canada
RAA Chapters in Action
RAA Winnipeg Visits North Dakota
The Winnipeg Area Chapter of the Recreational Aircraft Association viewed
an amazing collection of War Birds at a
recent 2-day tour to North Dakota. The
tour included the Fargo Air Museum
and Tri-State Aviation, both renown
for their significant collection of vintage aircraft and parts.
Stearman pilot Helen O’Connor,
Assistant Director of the Fargo Air
Museum, introduced the Fargo Air
Museum’s beautifully restored F4-U
Corsair, TBM Avenger, L 39 Czechoslovakian military trainer, P51 Mustang,
Fairchild PT-19A, a homebuilt T-tail
Poly Wagon used to teach the principles of fight to museum visitors as well
as a DC3 and another Czechoslovakian
jet trainer parked outside were some
of the highlights. The amazing 28 cylinder radial Pratt and Whitney Wasp
Major engine sitting quietly beside a
Merlin GT currently under construction by the local EAA chapter and an
award-winning replica of the Wright
Flyer connects the early beginnings of
aviation with the present. Other aircraft exhibits include a Huey Helicopter, and 1917 Standard. The museum
also has a library with 1000s of books,
magazines, original drawings and a
gift shop. The museum is raffling off
a fully restored 1964 Cessna 182. The
draw will be made next June, so contact the Fargo Air Museum if you are
interested in buying a US$50.00 ticket;
only 2500 tickets are available for sale.
Tri-State Aviation Inc., (TSA) in
Wahpeton ND, fabricates parts for,
and restores WWII aircraft, specifically
the P-51 Mustang. As an FBO, they
also service general aviation and agricultural aircraft, as well as manufacturing spray booms (Superbooms) for
Ag aircraft. Jon Klein, Shop Manager
March - April 2012
John Blackner with fellow Winnipeg gather around the Mustang A-Model engine bearer. Photo credit Jill Oakes.
and Cindy Schreiber-Beck shared the
history and current capabilities of the
business. TSA was founded by Gerry
Beck and has been in operation since
1974 at which time it was an aerial
spraying operation and FBO. Since
that time it evolved into a shop with
unique capabilities including hydroforming, prototyping, stretch forming, metal shaping (power hammer),
CNC machining, sheet metal repairs
and welding. With a capable staff of
nine, the company has continued after
Beck’s death in 2007.
The purchase of a TBM Avenger
without bomb bay doors was the
genesis of fabricating WWII aircraft
parts. Bomb bay doors were not readily available thus Beck decided to tool
up and build a set of doors. Building
the doors proved to be a successful
endeavor. Shortly thereafter the transition to Mustang parts occurred with
the rebuilding of a doghouse.
Beyond Mustangs, numerous warbirds have been through the shop,
including: F4-U Corsair and TBM, that
are on display at the Fargo Air Museum;
a Japanese Zero (Nakajima manufactured A6M2) that Blayd Corporation
of Carman MB completed the major
portion of the restoration; rebuild of a
Hawker Sea Fury; and numerous P-51
Mustangs for major rebuilds or component rebuilds, including the Red Tail
Mustang (C Model) and fabrication of
the A Model, the first A being Beck’s
“ultimate homebuilt” that is currently
under rebuild. Using original drawings, all components that could not
be purchased for the A are fabricated. That includes the engine mount that
was in process.
Of interest was the metal forming
shop. Randy Carlson’s expert hands
use a variety of machines, including
a power hammer, to create compound
curves in originally flat aluminum. Using dies that he machines, specific
curvatures can be achieved. Many
Mustang parts are unavailable for
purchase so Randy carefully crafts the
parts using drawings from the Smithsonian Museum and /or pieces of
RAA Chapters in Action
original parts as models. Most recently,
Randy completed exhaust pieces for a
B-29 and Jon showed us lower cowlings for the A Model that is currently
being made.
Another technique that the TSA
crew has mastered is stretch forming
aluminum using an in-house built
stretching machine and concrete dyes.
The Mustang air induction scoop is
being reproduced by pouring a concrete mold and finishing the concrete
until it is as smooth as silk. Then a
sheet of aluminum is clamped in jaws
on the massive, hand-made table with
hydraulic rams that push the concrete
dye into the aluminum to form the
part.
TSA also uses CNC machines to
produce precision parts. Mustang /
T-6 tail wheels can be produced along
with numerous aluminum parts. Again, the original drawings are utilized to program the CNC machine.
In another workshop the A Model
Mustang tail surfaces were being covered with fabric using countersunk
screws and counter sunk washers to
hold down the heavy-gauge tape. The
attention to detail is seen throughout
this amazing project, including stitching the fabric to the metal framing
openings in the leading edge of the tail
surfaces.
Cindy then took us into an adjacent
hangar where a room full of antique
engines, aircraft and cars greeted us –
to include Merlins, Allisons, Continentals to name just a few of the engines…
plus five Mustang fuselages awaiting customers to finalize the order,
tons of aircraft parts, 2 WWII military
vehicles, a B-25 Mitchell Bomber and
a Howard. Just when it seemed like
there couldn’t be anything else vintage
to see, Cindy completed the tour with
a close look at an amazing antique
machine that TSA used to make spools
Tri-State plans to have the A-Model
Mustang ready for flight.
RAA Scarborough/Markham Chapter
We wish to thank Chris Gardiner
(cgardn628@rogers.com)
of
the
Larry Brown and John Blackner retracing the wire routing on
TSA’s antique wire crimping machine. Photo credit Jill Oakes.
of wire fabric clips. The machine produces the Martin Fabric Clips that
are used to secure fabric to metal ribs
without rib stitching. TSA specializes in the tools, skills
and knowledge needed to restore
vintage aircraft with excellence, producing their own parts when it is
impossible to buy replacement parts. The shop began as an Ag plane repair
shop and now is comprised of a staff
of 9 with the capabilities to rebuild
warbirds. TSA works closely with
similar shops across North America
and is known internationally for their
exceptional workmanship and ability
to fabricate parts. RAA Past President
Harry Hill originally planted the idea
to tour Tri-State Aviation about 10
years ago; current President Jim Oke
picked up the idea this Fall. We look
forward to returning next year when
Oshawa RAA chapter for talking to us
about building composites in general,
and the KR2 aircraft in particular. It
dates from 1972; about 2,000 have been
built. The KR2 (now the KR2-S) is one
of the early composites with some of
the following specifications: a taildragger (although a few have been built
with tri-gear); wooden frame of Sitka
spruce, mahogany and birch, all glued
together with no screws; 700 lbs empty
weight, 1150 lbs gross; 25.5 ft span
with small flaps; 36 inches wide (Chris
calls it a marginal 2-place aircraft - no
baggage with 2 people!). Chris built
his aircraft at a total cost of about
$45,000 with a new 2180 cc VW engine
of 75 HP @ 3400 RPM equipped with
dual ignition (1 magneto, 1 electronic)
and a 54-inch diameter x 48-inch pitch
propeller. With this prop, its performance figures are: 145 cruise (all in
Join the RAA Forum
RAA's new forum is online! We hope to add many
features over the next while to enhance the value of your
membership. The URL is the same at raa.ca - once you're
on the home page, simply click on the "forum" tab to
get there. You'll find it a useful place to exchange ideas
and ask questions - but it's only as good as the people
who contribute to it. Help make this a useful resource for
builders and pilots.
Any suggestions and ideas for improvements are welcome
and can be sent to George Gregory at gregdesign@telus.
net. Stay tuned for further developments!
March - April 2012
MPH); approach at 70; touch down
at 60; stall at 52; 800 ft/min climb at
100 MPH. Chris says it is somewhat
twitchy to fly. The aircraft first flew in
2001 after a 4-year build time. Chris
gave us construction details which
were very interesting. The fuselage is
built like a boat. The wings have main
and rear spars, polyurethane foam
ribs, and pink foam panels in between;
a great deal of careful sanding is
required (wear a mask at all times
- much dust!). There are 2 layers of
fibreglass on the top and bottom wing
surfaces, 3 on the leading edge. Each
surface requires a one-day, one-piece,
continuous lay-up with aeropoxy. The
epoxy is applied with a roller over 6 oz
BID (cloth layers with a bi-directional
weave), finishing with peel-ply to
leave a smooth surface. We are most
grateful to Chris Gardener for giving
us such an excellent insight into composite building.
RAA Ottawa
This month we held our winter Ski
Fly-in. Like many of the winter flyins
this year ours was weathered out. We
had clear skies for part of the weekend
with but winds of 20 knots and gusting to 32 knots there were no fly-in aircraft this year. Inspite of the weather
we did have a very pleasant brunch
at the club house. Visitors from as far
away as Renfrew arrived to share the
very tasty brunch and tales of flying
did brighten the day. I hope to include
a few pictures next month so please
send in any pictures that you may
have taken at the indoor fly-in.
RAA London-St.Thomas
Phil Hicks reported that he now has
wing spars cleco-connected, but otherwise looking like twelve-foot long
wing spars. Dave Hertner reported
that his radio problem was an incorrect
RS-232 connector wire, which is now
fixed, and that currently a fuel flow
sensor anomaly is being addressed.
March - April 2012
Chapter 85: Back row from the left: Mark ter Keurs, David Marsden, Peter Klein, Tom Boulanger, Gary McBride, Roy
Taylor, Raymond Colley, Bruce Prior, Tim Nicholas, Tedd McHenry, Gerard Van Dijk, Cyril Henderson.
Front Row: from left: Alex Routh, John Macready, John deVisser. Missing: Francois Leh, David McIntosh, George Gregory
Talks are underway with a prospective test pilot at this time. Denny
Knott reported the Skyhopper flew
on January 7th, with no other flights
since then. At 8:00 PM Denny Knott
introduced the speaker, Wilson Boynton. As an aircraft maintenance technician he began to encounter composite
aircraft structures, realized this was
where the future of aircraft structures
RAA Calgary Annual breakfast.
The RAA Calgary Chapter and the
Cu-Nim gliding Club are having
our fly-in/drive-in breakfast again
at the Cu-Nim Gliding Club Airport
(CEH2 Black Diamond) on August
25, 2011.Cost is $7 per plate. Last
year we had about 10 planes fly
out; we should try to beat that
number this year. Overnight
camping facilities! Several people
came out last year on Friday and
camped over.. There will also be
discounted gliding again, so do
not miss it. Contact Don Rennie at
DRennie@hemisphere-eng.com
was heading, and took training in the
field. So much so in fact, that now he
and his staff are qualified in Canada
and the USA to repair composite structures of all kinds. He has worked with
Great Lakes, Air Ontario, and Jazz
here in London. In 1992 he started his
company Renaissance Aeronautics.
They do advanced composite materials training for students that come
from countries all around the world.
Wilson presented a one hour slide
show which touched on a tremendous
number of fascinating subjects regarding material composition, the way
the composite material is applied and
how the carbon fibers are applied to
fuselage and wing structures by computer controlled robots. The accuracy
and complexity is way beyond human
capability as we saw from his slide presentation. If we took nothing else away
from his presentation, he stressed the
extremely toxic nature of many of the
composite ingredients, and warned
us that breathing respirators, masks,
and protective clothing must be used.
These chemicals have effects that may
not show up for months or years after
use and can have detrimental effects
on your DNA which may not show up
until the second or third generation.
Remember the Thalidomide deformities in babies years ago? Thalidomide is an ingredient in some of the
composites which he described. His
presentation was intensely interesting
and certainly informative.
Chapter 85 (Vancouver)
President John Macready:
I am very happy to be the President
of our chapter this year. I have been
associated with the RAA for about
continued on page 34
Chistian Boehm, Luftbild-Wetzlar
Viru
Good
Catching a
Reinhold Dresler’s Pipistrel
March - April 2012
us
Virus SW / by Gary Wolf March - April 2012
For many years a cross country
plane has been a Mooney, a Cardinal, or
one of the retractable Pipers, powered by a
large engine and capable of quickly covering a lot of distance between fuel stops.
Although these have four seats they rarely
carry more than two crew plus a weekend’s
worth of luggage, but they are roomy and
comfortable like an SUV, with SUV-style fuel
consumption. More efficient are the two seat
RV’s, Glasairs, and other fast glass aircraft,
trading interior space for speed, but still getting less than 30 miles per gallon of 100LL.
In the past decade a new category of high
speed personal aircraft has been emerging
from Europe, high tech lightweight two
seaters built from composites, and powered
by smaller, more efficient engines.
The cost of fuel in Europe has forced
manufacturers to design aircraft that have
much less drag so that they can achieve
good cross country speed. High strength
composites are being used to create lightweight wind-cheating airframes, and light
weight means that smaller engines may
be used. The Rotax 912S engine appears
to have most of this new market, largely
because of its low fuel consumption, light
weight, and compact dimensions. At cruise
rpms it is not uncommon for this engine to
use fewer than four US gallons per hour,
and it runs happily on much less expensive
unleaded auto fuel.
There are dozens of European manufacturers now building two seat sport planes
but the one that stands out above the crowd
is Pipistrel. This company has embraced
new technology like no other. They have
been designing and manufacturing high
performance sailplanes for many years so
they have their low drag, low sink rate act
together. Their powered aircraft benefit
from what they have learned from sailplane
design and manufacture, so less of the
engine’s power is used to overcome gravity and more can be used to make it move
forward.
Pipistrel’s manufacturing process is very
clever. In Eastern Europe there are many
manufacturers of aircraft components, so
Pipistrel carves out their moulds on CNC
machinery and sends them out to the
subcontractors who then make the parts.
Everything is tracked, right down to the last
bolt and the name of the technician who
tightened it. Pipistrel tests everything to
certified standards and documents it all for
their civil aviation authority. Their intent is
to be producing certified aircraft in the near
future.
Have a look at the Pipistrel Virus (pronounced vee-rus when calling the Tower)
and squint a bit and you will see a sailplane
with a prop on the front. The wings are long
and have a high aspect ratio, even on this
Virus SW (short wing) version. Thirty five
feet of span with a short chord means low
drag. The fuselage begins with a spinner,
and the tightly fitted engine cowls are round
in cross section for minimum wetted area.
These cowlings flow seamlessly to the cabin
that is essentially an oval shape, closing
again to become a small diameter tail boom
with a T-tail. The wings and empennage are
smoothly faired to the fuselage and nothing
sticks out anywhere. The main and luggage
doors fit flush and tight to the cabin and
only the fasteners holding the landing gear
stick out into the airstream. The watchword
is smooth.
The laminar flow wings of the Pipistrel
Virus SW are carbon composite, cantilevered as they would be in a sailplane, and
they plug into the carrythroughs and may
be removed quickly. The full length gapsealed flaperons have a range of +18 degrees
down to 5 degrees reflexed, and the tips are
drooped to minimize vortex losses.
The T-tail is quite small but quite
effective. The top mounted horizontal
stab operates in clean air so it can be
smaller than one mounted low on the
tailboom. It also provides an endplate
benefit to the vertical tail, improving
the effectiveness of the rudder. Both
the rudder and elevator have flush gap
seals to minimize leakage through the
hinge area.
The cabin and tail structures are of
carbon composite sandwich construction with inner and outer skins bonded
to a foam core, and a composite wing
carrythrough traverses the top of the
cabin. Steel tube triangular weldments
are fitted ahead and behind the carrythrough to give diagonal stiffness
to the top of the cabin, allowing large
skylights for good sight lines in the circuit. These also provide the mount for
the harness of the BRS. The seat frames
are structural in this plane so they
cannot be moved. Instead the pedals
are mounted to tubular subframes that
may be adjusted fore and aft to fit the
crew. Luggage space is provided on a
low shelf behind the seats, with room
for 100 pounds. Even this removable
shelf is made from foam clad both
sides with carbon fibre and it weighs
only a few ounces. The BRS chute is
mounted behind the passenger’s seat
and there is a sacrificial composite
plate in the roof and a rocket exhaust
port in the floor. The harnesses are
taped to the top of the fuselage
and fasten to the rear carrythough
structure, and if deployed the plane
assumes a slight nosedown attitude.
The two control sticks are well
placed and the throttle quadrant is
centrally mounted. Prominent on
the panel is the control knob for the
optional Pipistrel-manufactured variable pitch prop. This knob requires a
lot of turns during transition to cruise
flight, and then some fine-tuning along
with throttle adjustments to optimize
manifold pressure for minimum fuel
burn. An electric constant speed prop
is also available. Elevator trim is
between the seats and it is a bit coarse
in operation, but stick forces are so
light it is entirely possible to leave it in
place for the entire flight. This trim is a
cable-operated spring bias rather than
a trim tab so it cannot be used as a
secondary elevator control if one of the
elevator cables should ever break.
Landing gear is a composite
hoop that has an airfoil shaped cross
section. Since this plane was being
ferried home in snowy weather the
main wheel pants were removed. As
expected, they weigh nothing. The
steerable nose gear is a steel tube
with an aluminum fork at the bottom.
The nose wheelpant is so enveloping that it is necessary to remove the
wheel to check the tire pressure. In the
walkaround the tire pressure check
is for three fingers of vertical space
between the ground and the bottom of
the wheelpant. Hydraulic brakes with
toe actuators are at both crew pedals.
The engine compartment is an
example of good packaging. Rad and
oil cooler are fed through submerged
ducts, and the exhaust system is very
effective. The 912S engine is almost
silent with this system, and its outlet
projects only slightly into the airstream. If more planes had a system
Spoilers and the Virus
When Reinhold Dresler ordered his Pipistrel without the spoilers
two years ago it was from a US dealer because at the time there was not
a Canadian importer. It quickly became apparent that spoilers would be
very desirable for landing in short fields. Unfortunately the structure and
mechanism must be part of the factory manufacturing process and they
cannot be retrofitted. Presently the Canadian dealer does not sell a Virus SW
without them; here's his description of what it's like to land with spoilers.
24
RAA Recreational Flyer
To land the Virus SW, you throttle to idle in the downwind, work
your flaps through the different stages as you bleed off the speed
(from -5° to 0° to +9° to +19°. Final approach is at 50 knots with full
flaps (19 degrees) and use the spoilers to increase the descent rate
just like you would reduce the throttle in most other aircraft. (Rotax
912 is liquid cooled, so shock cooling is not a concern). Once the
wheels touch the runway, immediately go to full spoilers and the
March - Without
April 2012
airplane is almost instantly firmly planted on the runway.
Far left: Elevator trim is a spring bias system. Left, A look inside demonstrated the cockpit is well placarded. The trim control is a slider and locknob. Centre, The BRS 'chute sits behind the
passenger; Above, the luggage compartment door fits flush and locks. Right, Nick Jones holds the carbon fibre luggage floor and tailcone cover which weigh almost nothing.
like this there would be no complaints
about aircraft noise. The Pipistrel prop
also contributes to the low noise footprint, and even in climbout the Virus
is almost unnoticeable.
This particular Pipistrel is registered as an Advanced Ultralight, and
the process was anything but simple.
Reinhold Dresler placed his order
nearly two years ago, and at the time
there was no dealer in Canada so he
was to take delivery from the dealer
in New Mexico. Although Transport Canada does not do any sort of
physical inspection of an Advanced
Ultralight, they are fastidious about
whether t’s are crossed and i’s are
dotted in the paperwork, and at the
time there were a few question marks
about the factory documentation, a
problem that has now been solved.
Finally in December of 2011 after his
plane had been sitting in a hangar
in New Mexico for two years, Reinhold and his friend Nick Jones took
an airline flight to Albuquerque and
began their trip home to Ontario in
midwinter conditions. The familiarization flight was brief but Reinhold
and Nick are experienced pilots, and
they focused mostly on approach and
landing techniques. They also spent a
full day in the hangar getting familiar
with the avionics including the Dynon
D180 combined EFIS/EMS, Garmin
496 GPS, TCAS, Transponder and 406
MHz ELT.
The recommended takeoff procedure is to use 18 degrees of flap and 52
KIAS to 50 ft, and then begin reducing
flap in stages. The plane will be off
the gound in only a couple hundred
feet. Best angle airspeed is 52 KIAS,
at 60 KIAS the flaps must be raised to
9 degrees, and at 70 KIAS they must
be raised to zero. Best rate is then 75
KIAS and at 80 KIAS the flaps are
reflexed to – 5 degrees.
In level flight the Virus SW can
cruise happily on 75% power at 147
spoilers it likes to keep flying for a few hundred feet.
Videos of myself playing around landing, flying by, taking
off etc. in different locations (the landings are with the use
of spoilers) can be viewed on Youtube at http://youtu.be/
xopFS1AzCJk?t=1m11s
Things I like about spoilers...
1. when you touch your wheels to the runway, full spoilers keep
them there, planted firmly even in direct crosswinds up to 30 knots.
2. Circuits. I can honestly do 5 circuits in the time it takes the
students in the 172 at the local flying school to do 1 circuit. March
- April
2012
3. Descent
rate. With negative flaps, throttle to idle, full spoilers, KIAS (170 mph), and at full throttle
the pilot must be careful not to lower
the nose or the plane can go past the
163 knot true airspeed Vne. At 8000 ft
this is 145 knots indicated airspeed.115
KIAS gives a fuel consumption of 51
miles per US gallon of 91 octane auto
fuel. This is 55% power at 4300 rpms,
a very low number for a Rotax, where
the burn rate is 2.7 gph. Pushing the
speed up to 147 KIAS results in a burn
rate of 4.3 gph and 41 miles per gallon,
pretty good for two people, full fuel
and up to 100 pounds of luggage
going fast across the country.
Although Rotax allows the use of
E10 alcohol-bearing fuel Pipistrel will
not, because the fuel is kept in the wet
wings and they do not wish to risk
any damage to the structure. Esso and
Shell 91 are OK but Reinhold and Nick
check for alcohol before every fillup.
The stick forces are light and controls are coordinated, their responsiveness varying with airspeed. At cruise
holding the nose down at 130 knots the descent rate is 5000 fpm. The airspeed will not increase.
4 spot landing, even a bad pilot like me, can land on the numbers
every single time using the spoilers!
5 landing distance is reduced significantly, to an average of 350
feet if brakes are used. (about 650 feet if you keep your feet off the
brakes)
6. Obstacles. You can drop down rapidly after clearing the power
lines or trees that block an otherwise perfect landing field.
Jonas Boll
Chistian Boehm, Luftbild-Wetzlar
Reinhold's Virus(pronounced vee-rus) is a pretty airplane in flight.
Lower right: The upper cabin is braced by a triangulating structure made of steel tube.
Another is on the forward side of the carrythrough.
Bottom: the glare shield drops down at the corners for better sight lines. The prop
pitch knob is on the panel and the throttle and choke are centrally located on the floor.
The foot pedal assemblies may be adjusted fore and aft.
speeds it is usually enough to simply
think about moving the stick to make
slight corrections, actually moving the
stick can result in over-control. Roll
rate is very fast at 1.6 seconds from 45º
to 45º. The rudder does not self-center
so it’s important to check the ball to
minimize drag. At low airspeeds right
down to stall the stick is still well coordinated and light, but requires more
movement, as one might expect. There
is never any feeling of inadequate
control.
A stall with stick held full back is
just a mush with a healthy sink rate,
and the ailerons still work. Stall speed
with full flaps is 35 KIAS, and even
with them reflexed 5 degrees it is still
only 46 KIAS. Service ceiling is 22000
ft and the glide ratio is 15:1, impressive for a plane that is flying on 102
square ft of wing at a loading over 12
pounds per square foot, a testament to
the efficiency of the Virus SW. There
is a good reason for the prominently
displayed NASA stickers on this plane
– for two consecutive years it has won
the efficiency competition sponsored
by NASA.
The circuit presents some unique
problems for this particular example of
the Virus SW. Spoilers were an option
when this plane was purchased and it
looks as if they should have been standard. The plane is so slick that with a 3
degree obstruction the minimum field
Virus
throttle is pulled to idle and on final
the indicated airspeed must be 50
knots with the flaps at 18 degrees. At
this setting the sink rate will be 450
fpm and a very aggressive slip will
Specifications
Wing area........................................ 102.36 square feet
Wing Loading.................................12.03 lb/ sqare foot
Gross Weight (AULA)..........................................1232 lb
empty weight...................................................~632 lb
Useful Load (AULA)..............................................600 lb
Fuel capacity.............................................. 13.2 US gal
Fuel use (170 mph, observed)............... 4.3 gph/41mpg
Fuel use (132 mph, observed)............... 2.7 gph/51mpg
Best L/D...............................................17to1 at 73 mph
Sink Rate (1232 lb, observed)...................450 fpm max
Rate of climb (1041 lb).................................. 1200 fpm
Range.......................................................... 1025 miles
Stall, clean..................................................... 49.8 mph
Stall, flaps................................................... 39.76 mph
Cruise (75% power)..................................... 152.8 mph
length without spoilers is 1640 ft, and
this assumes that the pilot has been
exact in maintaining correct airspeeds
and flap settings. Approach to the
circuit is at no more than 80 KIAS and
then the flaps may be at zero. The
downwind speed is 60-70 KIAS with
9 degrees of flap. At the base turn the
March - April 2012
Many who have a hangar at a rural strip must do without electricity. It can be rather expensive to bring it in from the main road, and then there is the monthly meter charge, all for a few
hours of usage per year. Still, it would be nice to have electric lights, a couple of 110v outlets, and perhaps an electric bifold door. Len Litwiller built his own Zenith 701 fifteen years ago and at that
time solar panels were onerously expensive, so he used a 12 volt drill, wired to his truck's battery with twenty feet of lamp cord. A few years ago he decided to electrify his hangar using solar cells
from Harbor Freight. Two 3-cell sets cost under $400 and provide 90 watts of power. He mounted heavy copper buss bars to a panel in his building and uses three deep cycle batteries to store the
electricity. The system has two inverters, 3000 watts and 1000 watts, and their output runs to his shop wiring.
Len's hangar workshop now has 110 volt outlets all around, and from these he powers his table saw, drill press, and the usual
grinders and hand drills. The hangar also has a small apartment with a student-size fridge, a radio, and compact fluorescent
lights. Well water is delivered to a plastic storage tank by an inexpensive 110 v immersion pump. Daytime lighting for the
hangar is by ambient light that shines through half a dozen translucent panels. The cells have so far been suffcicient for the
modest demand that Len puts on the system. For local ground transportation Len uses an electric bike/scooter with lithium-ion
batteries, charged from his solar system.
result in 800 fpm.
In gusty conditions or a crosswind, the approach is usually flown
at 60-65 KIAS with 9 degrees flap, but
a longer float in ground effect should
be expected. Nick has landed with
crosswind components up to 15 knots
and also in winds gusting to 26 knots
– taxiing in those conditions is more
of an issue than landing. Nick has had
to do three go arounds so far due to
falling back on old habits and flying a
tighter circuit that is no problem in a
Cessna, and subsequently crossing the
threshold at several hundred feet. If
the tower wants the speed picked up
the plane can cross the threshold at 80
KIAS at 30 feet but will require several
thousand feet to bleed off the speed
and touch down – this is simply not
an option at most airports. Remember
too that the flaperons must be reconfigured for each airspeed limit, so
the pilot must be on his toes. Spoilers
will cure the problems of floating in
ground effect and low sink rate; Reinhold is investigating the possibility of
having them retrofitted.
Because the Pipistrel Virus SW
can be registered as an Advanced UL
it may be legally flown by a newly
minted Ultralight Pilot with just ten
hours of flight time in a little fabric 2
stroke. Planes like the Pipistrel were
never even imagined back in the early
nineties when the Advanced UL category was set up and the privilege of
flying them was given to the holders of
the PP-UL. Fortunately the over $100K
price of these planes will keep them
March - April 2012
out of the hands of most novices.
In the US the Virus SW can be
a Light Sport, and the higher gross
weight allows another 88 pounds of
payload. With an empty weight of 640
pounds, this means a payload of 680
pounds. Unfortunately for those who
want speed, the Light Sport category
does not allow inflight adjustable propellers, and the maximum allowable
airspeed is 120 KIAS. Manufacturers
usually specify a prop that will limit
the plane to the category limit.
Jaime Alexandre of MD-RA
recently attended at the Pipistrel factory in Slovenia to see if the kit version
of this plane would qualify for the 51%
requirement of the Amateur Built category. The plane does meet the requirements so it may be built as an Amateur
Built aircraft. There is not much money
to be saved compared to buying a factory built, but the advantage is that the
builder can then have the higher gross
and payload, and equip the aircraft for
night and IFR flight.
Rotax has recently announced their
new fuel injected 912iS engine that
uses 21% less fuel. Pipistrel has been
chosen as one of the launch customers for this new engine, so real world
fuel mileage will be in the 50-60 mpg
range, even better than a tiny hybrid
car. Just be sure to put an “X” in the
box for the spoilers.
For more information:
Pipistrel Aircraft Canada Inc.
Box 1828 Whitecourt AB T7S 1P5
780-779-8907
info@pipistrel.ca www.pipistrel.ca
Half a dozen solar cells are mounted to the roof at the
appropriate angle to the sun. Wiring runs through
grommeted holes sealed with silicone rubber. Simple
mounting system
A bank of deep cycle batteries powers everything,
including the pump for the water tank.
Local ground transportation is solar powered too.
Innovations
Transition Production
Prototype Flies
We've been following this for a few years. In spite of the economic troubles
of the day, Terrafugia has upped their game by flying the next version
www.terrafugia.com
of their street-legal airplane. The canard is gone, and the entire
vehicle has a much more finished look to it. A video of the aircraft in
flight and on the road can be seen at: http://bit.ly/HdQcMG
Dutch Personal Air
Vehicle Takes to the Sky
The Dutch Company PAL - V recently
announced the successful flight of their
first model, the PAL-V One, (Personal
Air-Land Vehicle). The vehicle is a delta
tricycle - two wheels in the back, one in
the front - and leans when cornering,
driving more like a motorcycle. The
prototype has a very finished look and the
styling is exquisite. They are now looking
for investors to move to the next stage.
The PAL-V-1 is an autogyro. This is actually
a very sensible option for a dual-use
aircraft as the rotors are considerably
smaller than wings and less complex to
stow; couple that with an autogyro's low
landing speed and invulnerablity to stall
and you have a winning combination. It
even has two seats. When can I have one?
For more information, check out their
website (and videos!) at http://pal-v.com/
www.palv.com
Anita Infante
Carter PAV Continues to Meet Milestones
From Carter Aviation Technology's Website:
The PAV (Carter's Personal Air Vehicle Prototype) continues to expand the flight envelope
during Phase II Flight-testing. One of the major
milestones during the most recent series of tests
was to accomplish zero-roll, jump take-offs with
the wing extensions added to the airframe. Vertical take-offs are not the most efficient way for any
aircraft to take flight, but they allow for complete
runway independence, a key advantage of our
technology. The PAV has now demonstrated its
capability for zero-roll take-offs even though the
rotor has yet to reach optimum rpm in testing for
a significant, high altitude jump. Phase II Flighttesting will continue next week with an aim to
increase cruise speed, altitude and time in air. The
ultimate goal for the PAV in testing is to exceed a
rotor advance ratio of 1. This would position the
PAV as only the second rotorcraft in history to
Carter's prototype during Phase 1 testing. It has since had its wings attached as the test program explores cruising
achieve this impressive milestone.
flight. The heart of the Carter concept is to generate cruising lift with conventional wings, allowing cruising speeds in
A video can be found at http://www.youexcess of those rotorcraft are capable of while retaining the vertical takeoff and landing capabilities of helicopters in a tube.com/watch?v=Bw8TIFENPuc&feature=dig
simpler aircraft. Photo by Carter
est_fri
March - April 2012
Drill Doctor
Can the good doctor beat hand sharpening your bits? / RAA
Building an airplane means
drilling a lot of holes, and these must
be drilled to accurate diameters to
provide the bearing area to transfer
the load from one part to another.
Unlike motorcycles, boats, and other
toys, aviation cannot afford the weight
penalty of oversized fasteners. The materials we use can sometimes
wear out drill bits quickly, and they
must then be sharpened or replaced.
Drill bits are not expensive but it
can be a bother to run out to the tool
supply, so a good drill sharpener is a
handy shop item.
The Drill Doctor 350X purports to
be able to sharpen any size drill up
to 1/2" so I bought one for testing. It
consists of a motor with a small diamond wheel, and a collet chuck with
alignment fingers to ensure that the
drill bit will be properly presented
to the diamond wheel at the correct
angle and clocking. The bottom of the
chuck has a cam that causes it to rise
and descend as the operator rotates
the chuck. It normally takes a dozen
to twenty rotations to renew the tip of
a drill, about one minute.
March - April 2012
I took pairs of brand new drills
and resharpened one of each pair on
the Drill Doctor to see how well the
machine worked, and unfortunately
the results were not as good as a factory-sharpened drill. The diamond
stone is a bit coarse but this is not the
real problem. With the unit I had the
problem seemed to be the accuracy
of the chuck itself. On the 3/8" drill
the cutting edges became unequal in
length, suggesting that the drill was
not postioned in the chuck's exact
centre. A test drilling in mild steel
showed that the drill cut .012" oversize, even when there was a pilot
hole, so I tried sharpening the drill
again and got the same results the
second time.
On a 5/32" drill the clocking of the
bit was also a problem and it appears
that the indexing points in the collet
chuck were inaccurately positioned.
This resulted in a bit that did not
have enough relief behind the cutting edges. A test drilling in mild steel
required a lot more effort than with a
new drill bit, and the bit made grumbling sounds; again the hole came out
oversized. The bits would have been
good enough for the usual household
work but not nearly good enough for
aviation.
A friend has the same machine
and he is happy with his but he
is drilling through sheet metal for
pulled rivets, and a few thou oversize does not matter. He sharpened a
drill bit for me and I did another test
hole in the steel block. This drill came
out of his Drill Doctor with the flutes
closer to the same length, and the
test cut in the steel block produced a
hole that was still oversized but not
nearly as much as on my machine.
The sharpened bit still had too little
relief behind the cutting edges and
grumbled as it cut the steel. A member
who is a retired tool and diemaker had
a look at the results and gave a knowing smile. He took the bits over to the
bench grinder and sharpened them by
hand, and all three then cut like new.
It is hard to beat experience.
Verdict: for aircraft, not recommended.
Top: The collet chuck has
indexing fingers to clock the
drill bit. Left, the collet chuck
is rotated and the cams on its
bottom cause it to rise and fall
to provide back clearance for the
cutting edges.
Buying a Drill Press
Is it worth buying? Here's a few things to check before you lay down your cash / RAA
Drill presses come in all qualities and prices and
builders buy these machines expecting that they will be
more accurate than a hand held drill. A drill press can be more accurate if
everything is set up properly, but before
buying one the builder should open the
box and do a basic check of the fit of the
quill in the headstock. This can be done
by extending the quill and giving it a
shake to see if it is loose. If it is, open
another box and try that drill. A drill
press with a loose quill is not worth
buying. If you wish to know how much
slack there is in a drill press that you
already own, use a magnetic stand and
dial indicator to determine how many
thou of slack there is. A good one will
have only .001" or .002", and a loose one
will have over .010". Drill bits tend to
self centre so if there is a good centre
punch divot or a pilot hole even a loose
drill press can do a reasonable but not a
great job of drilling a hole that is on size.
Where the slackness really shows up is
when using a holesaw, and especially
when using a single point flycutter. A
loose drill press will experience a lot of
vibration and runout with these.
Assuming that the quill is reasonably
well fitted, the magnetic stand and dial
indicator may be used to check runout
of the quill. Place the ball end of the
dial indicator against the Morse taper
shaft of the chuck and turn the chuck by
hand. If there is runout it is likely that
the Morse taper hole in the quill is not
concentric with its outside diameter.
Mark the high spot with a magic marker. Next step is to use a good bolt or a
piece of shafting, and insert it into the
chuck. Place the ball end of the dial indicator at a radius to the bolt or shaft and
again rotate the chuck by hand and
check for runout. A used chuck might
be filled with chips so remove the bolt
and blow the chuck clean, and try again.
Make a mark at the high spot and compare to the one on the quill. It might be
worth removing the chuck by using a
Morse taper drift in the slot in the quill.
Try the chuck clocked 180 degrees from
its original location and again use the
dial indicator to check runout. Try a few
more locations to see which produces
the best runout and when you are satisfied use a brass hammer to rap the
Morse taper smartly back into the quill.
The table of a drill press frequently
is adjustable for lateral tilt and there is
usually a label with degrees and a zero
line, but this zero line can be inaccurate.
Remove the shaft from the magnetic
stand and install it in the drill chuck,
then set the ball end of the dial indicator against the table. Rotate the chuck by
hand to see how much vertical runout
the table has. Loosen the clamp on the
drill press knee and adjust it so that left
and right are at the same number. Then
scribe a new zero line on the tilt label.
March - April 2012
The hardest thing to correct is
table tilt in the fore and aft plane. The
dial indicator will show if the table
is leaning out or in. With the shaft of
the magnetic stand in the chuck, again
set the ball end of the indicator on the
table and rotate the chuck. Note the
difference in readings right next to the
column compared to farthest from it.
A difference can mean a warped table
or an inaccurately machined knee,
the part that protrudes out from the
column. Try rotating the table to many
locations, checking each time to see
if warp in the table can compensate
for a mismachined knee. If you are
lucky this will work. If it does, then
make a mark on the table nearest the
column so that if you ever have to
rotate the table you can bring it back
to the position that makes it the most
level. If rotating the table does not
work to level it, loosen the tilt clamp
and insert a thin shim at the top or
bottom as necessary to bring the table
into level. Real machinists would
scrape the mating surfaces but a shim
works well enough for hobbyists.
P.S. Buy a magnetic stand and
dial indicator, usually well under $50
together and very handy.
Opposite: Check the total runout with a bolt or shaft in the chuck. Top left: Check lateral tilt of the table; Top right, Compare left and
right readings. Above: Loosen the knee bolt with a wrench and when satisfied scribe a new reference line for zero.
Denso Iridium IK 24 C11 Spark Plug Failures
The HKS 700 E engine specifies as its spark plug the Denso IK 24 C11 AND Unfortunately there
appears to be a manufacturing problem with these. Harish Jadeja, the member who flew his X-Air to
Oshkosh last year has already had three failures of these spark plugs.
The ceramic insulator of these plugs comes loose in the threaded steel housing and leaks out
combustion pressure, and also allows fresh air to be sucked into the combustion chamber.
This fresh air leak is uncarbureted so the mixture becomes lean and the cylinder and exhaust
temperatures rise.
The first failure experienced by Harish was quite pronounced, with the ceramic pushing out 1/4"
and causing a rapid and dramatic EGT rise. Harish did a precautionary landing and upon pulling
the plugs he found that one had failed. Since then he has had two more failures on subsequent
spark plugs, including the one that was recently found while doing his annual. This one was blowing
around the insulator as evidenced by the carbon tracks, and the cylinder was showing EGT's at the
maximum allowable. temperature. The insulator was loose enough that two fingers can spin the insulator in
the housing. The insulator can be easily rotated within the steel threaded section, indicating an internal seal
failure. Note the carbon tracks blowing up from the engine.
March - April 2012
Portable Power
Power you can take with
you / by Terry Jantzi
For the past couple of months I have been involved in building a
recumbent tricycle to satisfy my cycling needs, as I grow older and less able to
balance those silly newfangled safety bicycles. My project has grown from the
simplest possible to one with turn signals, horn, cell phone GPS and an MP3
player (with speakers). All these devices, besides adding weight, require a
plethora of batteries. I came to the conclusion that some sort of electrical system
was in order. I played around with a single 9V battery which powered my horn
and turn signals. However, my cell phone with the GPS application running
drains the phone battery very quickly. When I use it in the car, I keep it plugged
into a 12V to USB adaptor for continuous use and charging. If I use this power
supply while cycling, it will outlast my rubbery legs.
First a very important disclaimer: I have little understanding of electronics
and anything beyond simple circuits, other than they work because of the magic
smoke that’s sealed inside. I often accidentally let the magic smoke out, and
then my devices don’t work. Therefore this box is very simple, with off the shelf
parts. The complicated electronics came out of a blister pack, ready made. That
would be the USB adaptor.
I mounted an 8 cell battery holder, switch, 12V accessory socket and a 1 amp
fuse and holder into a small electronic project box. The batteries are in series,
so provide 12V. I can run or charge most low draw devices from it. I’ve charged
my Blue-tooth earpiece and with the 12V to USB adaptor, can get three full
charges into my cell phone. I’m currently using NiMH rechargable cells, which
March - April 2012
My project has grown from the
simplest possible to one with turn
signals, horn, cell phone GPS and
an MP3 player (with speakers).
provide 10-11V but seem OK. It is tempting to plug higher
load stuff into the accessory socket which quickly results in
that “magic smoke” syndrome, hence the fuse wired into the
circuit.
All parts were purchased at a local electronic surplus
store. With a dollar store pack of batteries, the total cost came
to just over $12. The switch in the circuit isn’t really needed.
I think it makes the project look more complicated and the
builder more intelligent. But, I do leave the USB adaptor
inserted most of the time so it doesn’t go travelling. Apparently it and my reading glasses are buddies and have a touch
of the wanderlust. When inserted, it does have a minor current draw which does eventually deplete the cells.
The AA battery version of the box weighs 370g (13oz).
This project could easily be scaled up with bigger batteries. I
have used an eight series D cell pack to run a small electronic
picture frame all day at a trade show.
NOTE: the picture on the phone is my “cover model”
wife of 31 years. Makes owning a phone worthwhile, just to
have the photo with me all the time.
Many of us fly single seat aircraft without electrical systems and the remedy is sometimes a hodgepodge of wires. Terry Jantzi has
designed a tidy and simple solution that can be
used to power a handheld radio, gps, and cell
phone.
His aircraft building pursuits go back to the
early nineties when he began the build of his
first plane. In 1997 Terry Jantzi completed his
RV-6 and won an "outstanding workmanship"
award at the 1998 Oshkosh event. Next he set
over 20 world speed records and finally a Canadian altitude record of 26137 ft. He enjoys sharing his pursuits with others, evidenced by the
312 first time passengers he flew in his aircraft.
Lately he has designed a solar oven that is now
being used in third world countries as well as (in
his words) “numerous less useful” inventions.
An avid cyclist and marathon runner, Terry's current project is a self-built recumbent tricycle that he will use for commuting to
work and general recreation.
March - April 2012
Chapters / continued from page 21
10 years and have served in positions such as Custodian and Program
Director. Previously, having been a
volunteer and a member at large on
DapCom, I was known as” John the
Grass Cutter”! One of my projects
in those days was the creation of an
ornamental meadow and “Loadstar
Park”. I have a picture of our group
dedicating Loadstar Park during a
past July Fly In. Don Watson, a previous park caretaker and I started the
Remembrance Day Ceremony and
our group has kept it going successfully for 8 years. Although I have
never actually built a homebuilt
airplane, I do fly and look after my
Cessna 140, C-FPJP at Delta Heritage
Airpark.
The position of President is not
one I take lightly. I am aware of the
trust you have bestowed in me and
I will do whatever I can within the
limits of my abilities to maintain your
trust. I ran for the position because
I had some ideas about how we can
maintain the integrity of our chapter and tidy up some organizational
issues. We at Delta Heritage Air Park
have a lot to be thankful for. We have
great facilities, almost our own airport, a beautiful little place to hang
out and some great people to associate with. It’s in this context that I
believe we have a good future and I
am optimistic that we can keep our
Chapter active and engaging.
We have observed recently that
our organization appeared to be
floundering in our ability to describe
ourselves and our purpose. To rejuvenate and reorient our members
I thought the first step would be a
meeting to discuss what it is that we
should be doing to efficiently run our
organization.
One of the first ideas involved
meeting the executive committee
to talk about what we actually do. I
have noticed in previous years that
new executive members do not fully
understand or agree about their
respective roles and responsibilities
on the committee. With this idea in
mind and recognizing the limitations
of regular meeting times I decided to
organize a Saturday morning seminar to give our executive members a
chance to meet and discuss what each
person’s duties were to be.
The chapter constitution and that
of the national organization were
used as basic references for our discussion. In addition each individual
member was requested to prepare
a list of duties they thought were
required for each of their respective
positions. During the course of the
discussion other fellow members contributed what they thought the position ought to be.
The executive of Chapter 85 is
composed of the usual four mainstream positions, plus a Past President, seven Directors, a Custodian
and a Program Chairman. In addition
the chapter appoints several individuals into non elected positions such
as the Aircraft Chairman, Hangar
Chairman, Membership Chairman
and Newsletter Chairman. The airpark Caretaker and a check pilot are
two other non elected people invited
to serve on the committee.
In all this year we have a group
of eighteen eclectic individuals
from various backgrounds some of
whom are ex career aviators. We
have former military and commercial pilots, ex-academics, engineers,
financial specialists, a pharmacist, a
graphic designer, painters, mechanics
and several self employed business
persons. In all a very interesting and
dynamic group of individuals who
share the love of flying and building
airplanes. It would be inconceivable
to think our chapter couldn’t succeed
with all this talent. Notably however,
no women are on our executive committee this year!
Despite the managerial nature
of the topic most discussions were
robust and dynamic. It seemed that
most if not all individuals were very
keen on defining their role and that
of others in the group. We all wanted
to describe what it was we should be
doing and were eager to tell the other
person what he should be doing.
Chapter 85 is and has been a
very active Chapter of the RAAC in
the past. We have a long and distinguished history of aircraft development and construction. Some very
fine home built aircraft have come
from the hallowed halls of Delta
Heritage Airpark, most notably two
extremely fine examples of scale Spitfires and many others. The chapter is
very involved with participating in
the operation and maintenance of an
airfield, an activity which takes some
of our time and energy but which
pays enormous dividends in terms of
having the right facilities to pursue
our hobby.
We hope to keep Chapter 85
going for the foreseeable future. In
the months ahead our executive will
look at all aspects of our organization
its responsibilities and activities to
maximize the benefit to our members.
Our major object will be building and
taking care of airplanes but right now
I recommend some effort be put into
the basic building blocks of running
an efficient organization. In the short
term I propose we review where we
want to go, who we want to be and
how it is we are supposed to get there.
This means identifying activities, setting standards and defining our goals
and objectives, some less fun topics
but overall a dividend paying benefit
for the chapter in the future.
John Macready, President RAA Chapter
85 and RAAC Regional Director, BC
(Mainland).
March - April 2012
Coming Events
Governor General‘s Cup Caribbean Air
Challenge 2012 / Martinique Air show.
April 14-April 28 A full program will be
posted on www.airrally.com soon. For more
information: 450-969- 2247 or ctobenas@
airrally.com.
Winnipeg Learn To Land Seminar
Harv's Air, RAA and SFC are co-sponsoring
the "Learn to Land Course" .The course
begins with a ground school, April 13 and
20th from 7:00 - 9:00 at the Lyncrest Flight
Centre. To register contact jill_oakes@
umanitoba.ca
Annual COPA Rust Remover
April 29, Hanover, ON (CYHS) -Sunday. For
more information contact Phil Englishman
at penglish-man@copanational.org or 519377- 3777.
OHFC and COPA Flight 53 Spring Fly-In
Breakfast.
May 13, Stirling, ON (CPJ5) Event held rain
or shine. For more information, please
contact Rob Burns 613-475- 0867 or
Robburns2002@hotmail.com. http://www.
oakhillsflyingclub.ca/ohfc/ Welcome.html
Aviation and Space Museum grounds at the
Rockcliffe Airport featuring warbirds, classic
aircraft and vintage cars and flying displays.
For further information, please contact
Michel Cote at 819-684-9160 (aircraft) or
Ben Loiselle at 613-829-2203. Check out our
website at Flightworks.ca
St-Lazare Flying Club/Copa Flight 43,
Annual Fly-In Breakfast
June 10, St-Lazare, QC (CST3) from 7:00
a.m. to 11:30 a.m. New unicom frequency
123.5. For more information, contact Michel
Moreau at mjmorea@videotron.ca or 514694-2129. www.aeroclubstlazare.org.
COPA Fight 124, Champlain Flying Club
host their Annual Fly-In Breakfast
June 10, Cobden, ON from 07:00 until 11:00
hrs. CPF4 in the Supp. For more information,
please contact Larry Buchanan at 613-6382792 or lbuchan@ nrtco.net.
Kawartha Klassics Flyin
All pilots are invited to fly in to Lindsay
Airport CNF4 on June 9 2012 9-5 Please
call or email Flavelle Barrett 705-887-3414
f.barrett@rogers.com
and friends of everything Zenair-related:
Experimental, LSA, ultralight, floats and
more! Come tour the kit manufacturing
facilities, look at the finished planes of fellow
kit-builders and flyers. This event ties in with
the annual Huronia Airport Day and local
RAA fly-in: All are welcome! Drive or fly-in.
http://www.zenair.com
Cornwall Flying Club/COPA Flight 59
Annual Father’s Day Fly-in Breakfast
June 17, Cornwall, ON (CYCC) 08:30 a.m.
until noon. For more information,memail
Barry Franklin at barry.franklin@sym
Les Faucheurs de Marguerites
Sherbrooke airport, June 30th and 1 July, les
Faucheurs de Marguerites,
For more information, visit their web site at:
www.lesfaucheurs.com
Delta Pancake Breakfast
Second Sunday of each month - Delta
Heritage Air Park, Vancouver. Monthly fly-in
pancake breakfast by RAA Chapter 85 and
DAPCOM. Air Park location is in the CFS. Full
breakfast for $4. Breakfast served from 9am
until the food is gone or 11am, whichever
comes first.
Zenair Open House and Fly-in
Saturday, June 16, 2012 10:00AM - 4:00PM
Huronia Airport (CYEE), Midland,, ON, Canada
A gathering of builders, owners, pilots
Rideau Lakes Flying Club/COPA Flight 56
Breakfast Fly/Splash-In. May 26, Westport,
ON (CRL2) Located at N44 40.012, W076
23.799 using 123.2 for communication.
For more information, please call 613-2735282.
Chatham Seminar, Brekkie and TC Safety
Seminar
May 26, Chatham, ON (CNZ3): Breakfast/TC
Safety Seminar/Fly Market. The Kent Flying
Machines branch of the R.A.A, is pleased
to present the 10th Annual Fly-In/Drive-In/
For more information contact Gerrit van
Vrouwerff at 519-674-3851 or gerritvan@
aol.com
Capital Classic Wings & Wheels (formerly
Classic Air Rallye)
June 9, Ottawa, ON held at the Canada
March - April 2012
RAA Chapters and Meetings
Across Canada
The following is a list of active RAA Chapters. New members and other interested
people are encouraged to contact chapter
presidents to confirm meetings as places and
times may vary.
ATLANTIC REGION
HAVELOCK NB: Weekly Sunday morning
get together year round, all aviation enthusiasts welcome. Havelock Flying Club - 25
mi west of Moncton. Contact Sterling Goddard 506-856-2211 sterling_goddard@hotmail.com
QUEBEC REGION
COTE NORD (BAIE COMEAU): Meeting
times to be advised. Contact Pres.Gabriel
Chouinard, 418-296-6180.
LES AILES FERMONTOISES (FERMONT): First Sunday 7:30 pm at 24 Iberville, Fermont. Contact Pres. Serge Mihelic,
418-287-3340.
MONTREAL (LONGUEUIL): Chapter
415, Meeting in French second Wednesday
at 8 pm, at CEGEP Edouard Montpetit 5555
Place de la Savane, St. Hubert, PQ. Contact
president Normand Rioux at NRIOUX@
lapresse.ca
OUATOUAIS/GATINEAU: Every Saturday 9:00 am to noon at the restaurant
l9Aileron in the airport terminal. Contact
Ms N.C. Kroft, Gatineau Airport, 819-6690164.
ASSOC
DES
CONSTRUCTUERS
D’AVIONS
EXPERIMENTAUX
DE
QUEBEC (QUEBEC): Third Monday 7:30
pm at Les Ailes Quebecoises, Quebec City
Airport.
ASSOC
AEROSPORTIVE
DE
RIMOUSKI: First Saturday at 9:00 am, La
Cage aux Sports, Rimouski. Contact Pres.
Bruno Albert, 418-735-5324.
ASSOC DES PILOTES ET CONSTRUCTEURS DU SAGUENAY-LAC ST
JEAN: Third Wednesday 7:00 pm at Exact
Air, St Honore Airport, CYRC. Contact
Marc Tremblay, 418-548-3660
SHERBROOKE LES FAUCHEURS de
MARGUERITES. Contact Real Paquette
819-878-3998 lesfaucheurs@hotmail.com
ONTARIO
Barrie/Orillia Chapter Fourth
Monday 7:30 PM Lake Simcoe Regional Airport Contact Secretary Dave Evans 705 728
8742
E-mail david.evans2@sympatico.caCOBDEN: Third Thursday 8:30 pm at Club
House, Cobden Airport. Contact Pres. Clare
Strutt, 819-647-5651.
COLLINGWOOD AND DISTRICT; The
Collingwood and District RAA, Chapter
4904, meets every first Thursday of every.
month, at 7:30 PM except July and August,
at the Collingwood Airport or at off-site locations as projects dictate. The January meeting
is a club banquet held at a local establishment.
For more information contact Pres. George
Elliott gaelliott@sympatico.ca 705-445-7054
EXETER: Second Monday 7:30 pm at
Summers-Sexsmith Airfield, Winters-Exeter
Legion. Contact Pres. Ron Helm, ron.helm@
sympatico.ca 519 235-2644
FLAMBOROUGH: Second Thursday 8:00
pm at Flamborough Airpark. Contact Pres.
Karl Wettlaufer 905 876-2551 or lazykfarm@
sympatico.ca
KENT FLYING MACHINES: First Tuesday
7:30 pm at various locations. Contact
President , Jim Easter 519-676-4019
jim.easter@teksavvy.com.
KITCHENER-WATERLOO:
Meets the
third Monday of each month in the upstairs
meeting room of the cadet building at CYKF,
except during the summer months when we
have fly-ins instead. Please contact Clare
Snyder clare@snyder.on.ca
LONDON/ST. THOMAS: First Tuesday
7:30 p.m. At the Air Force Association building at the London Airport. Contact President
Phil Hicks p.hicks@tvdsb.on.ca 519-452-0986
Midland/Huronia
Meeting: First Tuesday, 7:30 pm at Midland/
Huronia airport (CYEE) terminal building. Contacts: President Ian Reed – 705-5490572, Secretary Ray McNally – 705-5334998, E-mail – raa.midland@gmail.com . NIAGARA REGION: Second Monday 7:30
pm at Niagara District Airport, CARES
Building. Contact Pres. Elizabeth Murphy
at murphage@cogeco.ca, www.raa-niagara.ca
OSHAWA DISTRICT: Last Monday at 7:30
PM at the Oshawa Airport, South side, 420
Wing RCAF Assoc. Contact President: Jim
Morrison ,905 434 5638 jamesmorrison190@
msn.com
OWEN SOUND Contact President Roger
Foster 519-923-5183 rpfoster@bmts.com
OTTAWA/RIDEAU: Kars, Ont. 1st Tuesday. Contact: Secretary, Bill Reed 613-8318762 bill@ncf.ca
SAUGEEN: SAUGEEN: Third Saturday for breakfast at Hanover Airport.
President:
Barry
Tschirhart
P.O. Box 1238 27 Ridout Street Walkerton,
Ontario. Home: 519-881-0305 Cell: 519-8816020. Meetings are held every second Tuesday evening, at 7:30pm. Location(s) Saugeen
Municipal Airport, Kincardine or Port Elgin.
All interested pilots are welcome. Email:
barry.tschirhart@bell.net
YQG AMATEUR AVIATION GROUP
(WINDSOR): Forth Monday, 7:30 pm Windsor Flying Club, Airport Road, Contact: Kris
Browne e_kris_browne@hotmail.com
SCARBOROUGH/MARKHAM:
Third
Thursday 7:30 pm Buttonville Airport, Buttonville Flying Clubhouse. Contact Bob
Stobie 416-497-2808 bstobie@pathcom.com
TORONTO: First Monday 7:30 pm at
Hangar 41 on north end of Brampton Airport. Contact: President Fred Grootarz Tel: (905) 212-9333, Cell: (647) 290-9170;
e-mail: fred@acronav.com
TORONTO ROTORCRAFT CLUB: Meets
3rd. Friday except July, August, December
and holiday weekends at 7:30 pm Etobicoke
Civic Centre, 399 The West Mall (at Burnhamthorpe), Toronto. Contact Jerry Forest,
Pres. 416 244-4122 or gyro_jerry@hotmail.
com.
March - April 2012
WIARTON: Bruce Peninsula Chapter #51
breakfast meetings start at 8:30am on the
second Saturday of each month in the Gallery
of Early CanadianFlight/Roof Top Cafe at
Wiarton-Keppel Airport. As there are sometime changes, contact Brian Reis at 519-5344090 or earlycanflight@symptico.ca
Don Rennie cgmmv.skylane@gmail.com 403874-0876
EDMONTON HOMEBUILT AIRCRAFT
ASSOC: First Tuesday 7:30 pm EAHS
boardroom. Contact President Bill Boyes
780-485-7088
GRANDE PRAIRIE: Third Tuesday, Chandelle Aviation Hangar, contact Jordie Carlson
at 780-538-3800 work. or 780-538-3979 evenings. Email: jcarlson@telusplanet.net
John Macready jmacready@shaw.ca. Website
http://raa85.b4.ca.
VANCOUVER ISLAND AVIATION SOCIETY (VICTORIA): Third Monday 7:30 pm
Victoria Flying Club Lounge. Contact Pres.
Roger Damico, 250-744-7472.
THOMPSON VALLEY SPORT AIRCRAFT
CLUB: Second Thursday of the month 7:30
MANITOBA Info Packs $10 /ea
pm
Club,
InfoKnutsford
Packs $10
/eacontact President BRANDON: Brandon Chapter RAA meets
Wally Walcer 250-578-7343
on the second Monday of each month at the
ALASKA HIGHWAY: meetings held every
Commonwealth
Air Training Plan Museum BRITISH COLUMBIA
third Thursday of every month (except July
2/3 Mustang
2/3
Mustang
AMF-S14
AMF-S14
ABBOTSFORD:
Third
Wednesday
7:30
pm
at one
7:30 PM
except
in the months
of
July
and
&seaters
August) at two
the &
Taylor
Hall at 7:30
& two
seaters
one
&
two
two & four seaters
four Fire
seaters
August. Contact Pres. John Robinson 204- Abbotsford Flying Club, Abbotsford Airport. p.m. For more information call Richard at
Contact President, John Vlake 604-820-9088 782-2421 or Heath at 785-4758.
728-1240.
Winnipeg: Winnipeg Area Chapter: Third email javlakeca@yahoo.ca
Flying Flea
Flying Flea
F12 Cruiser
F12 Cruiser
Thursday,
7:30 pm RAA Hangar,
Lyncrest DUNCAN: Second Tuesday 7 pm members
one
&
two
seaters
one
&
two
seaters
two
&
three
seaters
two & three seaters
Airport or other location as arranged. Con- homes (rotating basis). Contact Pres. Howard
HIPEC
Covering
HIPEC
Covering
tact President Ben Toenders at 204-895-8779 Rolston, 250-246-3756.
Chapter executives, please advise of changes
NOraa@mts.net.
RibstitchingNo meetings June, July OKANAGAN VALLEY: First Thursday
NO Ribstitching
or email
as they occur. For further information
NO Tapes Lo Labor
NO Tapes Lo Labor
& Aug. RAA Winnipeg info alsoF11
available
at of every month except July and August (no regarding chapterF11
activities
Sporty
Sportycontact RAA
Lo Cost… Proven!
Lo Cost… Proven!
Springfield Flying Center website at http:// meetings) at the Kelowna Yacht Club. Dinner Canada, Waterloo Airport, Breslau ON
FALCONAR AVIA INC.
AVIA
INC.
N0B 1M0 Telephone:
519-648-3030
Member's
at 6:00pm, meeting at 7:30pm Contact Presi- FALCONAR
www.lyncrest.org/sfcraac.html.
dent, Cameron Bottrill 250-558-5551sales@falconaravia.com
mon- Toll Free line: 1-800-387-1028
sales@falconaravia.com
SASKATCHEWAN
email: raa@raa.ca
www.falconaravia.comeypit@junction.net
www.falconaravia.com
Chapter 4901 North Saskatchewan. Meet- QUESNEL: First Monday/Month 7:00 p.m. web: www.raa.ca
780-465-2024
780-465-2024
ings: Second Tuesday of the month 7:30pm at Old Terminal Building, CYQZ
Prairie Partners Aero Club Martensville, Sk. Airport. Contact President Jerry
info at www.raa4901.com. Brian Caithcart is Van Halderen 250-249-5151
the chapter president. Contact email: presi- email: jjwvanhalderen@shaw.ca
dent@raa4901.com.
SUNCOAST RAA CHAPInfo Packs $10 /ea
Info Packs $10 /ea
TER 580: Second Sunday 13:30
ALBERTA
pm Sechelt Airport Clubhouse,
Calgary chapter meets every 4th Monday sometimes members homes. Coneach month
exception of holiday Montact Pres. Gene Hogan, 604-8862/3 with
Mustang
2/3 Mustang
AMF-S14
AMF-S14
days one
and &July
August. Meetings
fromseaters
7645
two&seaters
one & two seaters
two & four
two & four seaters
19:00-22:00 are held at the Southern Alberta CHAPTER 85 RAA (DELTA):
Institute of Technologies (SAIT) Training First Tuesday 7:30pm, Delta
Hangar at the Calgary Airport. Join us for Heritage Airpark RAA ClubFlying
Flea site visits, F12
Flying Flea
F12 Cruiser
builder
discussions,
tech. Cruiser
tips, fly house. 4103-104th Street, Delta.
one
&
two
seaters
one
&
two
seaters
two
&
three
seaters
two & three seaters
out weekends and more. Contact president Contact President President:
PLANS & KITS
PLANS & KITS
HIPEC Covering
NO Ribstitching
NO Tapes Lo Labor
Lo Cost… Proven!
G. A. P.
F11 Sporty
FALCONAR AVIA INC.
Geared
Air Power Industries
PSRU's for Subaru and Rotary engines
2.2, 2.5www.falconaravia.com
and 3.3 litre
780-465-2024
Planetary Gear 2.17-1
Ratio
Reworked Heads, Cams
John A.Vlake Tel. (604) 820-9088 Fax (604) 820-9113
email: johnvlake@gmail.com
www.gappsru.com
PLANS & KITS
Info Packs $10 /ea
PLANS & KITS
PLANS & KITS
HIPEC Covering
NO Ribstitching
NO Tapes Lo Labor
Lo Cost… Proven!
FALCONAR AVIA INC.
www.falconaravia.com
780-465-2024
Also single seat F9A & F10A & 2 seat
tandem Cubmajor, Majorette & Turbi.
*Add $3 postage for info packs.
PLANS & KITS
Info Packs $10 /ea
March - April 2012
2/3 Mustang
one & two seaters
F11 Sporty
AMF-S14
2/3 Mustang
AMF-S14
Classified Ads
To submit or delete a classified ad, please send to raa@raa.ca and place “RAA ad” in
the subject line.
The Recreational Flyer is pleased to offer you colour advertising within the magazine.
Previously limited to the back cover, we have added 4 new colour pages which will be
available with limited space for your advertising needs. Our rates for both black and
white and colour ads remain very competitive and you reach a captive and qualified
audience. Ads can be emailed to : classified@raa.ca
Deadline for submissions is the first of the month preceding date of issue.
Artwork: Rates apply to camera ready artwork. Digital files are preferred and should
be sent as email and in .txt format, PDF, JPEG, MS WORD, Photoshop or other
common file types. Advertising is payable prior to printing of magazine unless other
arrangements have been made. Payment is in Canadian funds. 10% Discount applies
to one year (6 issues) insertion paid in advance. Commercial Classified ad rates 1/8
page minimum.
Advertising Policy: The Recreational Flyer Publisher reserves the right to refuse
any or all advertising for any reason stated or unstated.
The Recreational Aircraft Association Canada does not assume responsibility for
advertisements, but does exercise care to restrict advertising to responsible, reliable
individuals.
Please note: Ads running more than 3 issues must be renewed to guarantee continued
display in the magazine.
For Sale
MINI-MAX ttsn 217 seoh 29.8. Rotax 447
new GSC prop. skis. radio. always hangared.
excellent condition $11,900.00 obo Dec11
For sale KR-2 fuselage in boat stage
and metal kit for retractable landing gear
castings $300.00 call Ian 604-856-1159 or
email tri-pyramid@telus.net Dec11
Propellers, wood, new, never mounted,
tractor cwise (view from cockpit), priced
OBO plus shipping: One 42x23, weight 2 lb.,
Lepper, conventional outline, 4 bolts on 70
mm b.c., $195. One 43x34, 4 lb., squared tips,
6 bolts on 75 mm b.c., $295 Call Frank, 905
634 9538
Bede-4 for sale! 380+ hours TTSN,
Recreational Aircraft Association Canada
President: Gary Wolf / Treasurer: Wayne Hadath
Recreational Flyer Magazine
Registration Mail Publication No. 09869
Contributing Editors:
Gary Wolf, Don Dutton, George Gregory, Wayne Hadath, Tom Martin
Art Director and Layout: George Gregory. Printed by Rose Printing Orillia, ON
The Recreational Flyer is published bi-monthly by the Recreational Aircraft Association Publishing Company, Waterloo Airport, Breslau ON N0B 1M0. Toll Free line:
1-800-387 1028 email: raa@zing-net.ca. Purchased separately, membership in RAA
Canada is $35.00 per year, subscription to Rec Flyer is $35.00 per year; subscribers
are elegible for reduced membership fees of $15.00 per year. Rec Flyer to have a single
issue price is $6.95.
The Recreational Flyer is devoted to the aerospace sciences. The intention of the magazine is to promote education and safety through its members to the general public.
Material in the Flyer is contributed by aerospace engineers, designers, builders and
restorers of aviation devices and vehicles, used in an amateur capacity, as well as by
other interested persons, publications and organizations. Contributions to the Recreational Flyer are voluntary and without remuneration. Opinions expressed in articles
and letters do not necessarily reflect those of the Recreational Aircraft Association
Canada. Accuracy of the material presented is solely the responsibility of the author
or contributor. The Recreational Aircraft Association Canada does not guarantee or
endorse any product offered through articles or advertising. The Flyer and its publisher welcomes constructive criticism and reports of inferior merchandise or services
offered through advertising in the publication.
Lycoming 0-320 E2D McCauley FP prop
75x53 2000 lb GW, 1285 empty. Murphy ext.
metal wings, 30 ft with droop tips. Vortex
generators, Extended flaps and ailerons.
Wing fold mech. built in! Complete set of
fairings - all design improvements complied with. Cessna gear legs with solid link
in gearbox. Murphy type nose wheel (5x4)
Towbar (2 pc) New brake discs and linings!
Endura paint - 2002. Complete upholstery,
adjustable seats, headliner, door panels,
carpets. Instruments: A/S, A/H, Alt., VSI,
Turn Co-ord., Slaved mag compass. Tach,
Vac. Gauge, Cyl. Temp (2) Fuel (2) oil press.,
amp. meter, clock/air temp and heated
pitot. King KX145 NavCom with KI205 Ind.,
ValCom 760, Flybuddy Loran, RT359 Transponder with Narco AR850 Encoder (mode
C) Magellan GPS with expansion card/software, Sharc ELT, 2 place Flightcom intercom,
2 headsets. Maintenance records, builder
manual, some spares, etc., halon fire ext.
first aid kit. Any serious offers near $27,000
considered. No tire kickers please. Located
CYNJ. Contact Fred Hinsch fred7@shaw.ca
For Sale. Lycoming 0-360-A4A. 279
SMOH c/w mags and carb. Recent prop
March - April 2012
strike inspection by Pro Aero Engines in
Kamloops. Yellow tagged. New bearings,
rings, gaskets, inhibited and crated, ready to
ship. $15,000. Barry Holland 250-785-6431.
w-b-holland@uniserve.com
2002 CP 301-A Emeraude. First flew June
2003. TTAF 50 hrs. 0 290G Lycoming 396 hrs.
since major. Sensenich metal prop inspected
and refurbished by Hope Aero June 15/09.
Dual controls (pedals, sticks throttle) custom
interior. Annual due May 2012. Always kept
in a hanger. Contact Jim Demerling 519-3489655 (Ont.) $ 21,500.00
VANS RV7A, by owner and 6 times Van's
builder. TT A/F and E 183.3 hrs. Lycoming
0320/ 160, AP, EFIS, KLX 135 with GPS
and Moving Map,GRT Engine Monitor, 3
blade Catto comp prop., etc, etc, list of eqpt
and more pic avble on request, Prof paint.,
new FlightLine int, superb workmanship
throughout. Manitoba, $110,000 204 371
5209, burtloewen@mts.net
AVID AMPHIBIAN KIT FOR SALE $5,000
Complete kit; tube fuselage and tail, all wing
parts, wheels, tires, hardware. Left wing
started. No engine, no mount, no instruments, no fabric. Contact Don, located near
Owen Sound, ON Telephone: 519 372-1383 .
email: we3kingers@yahoo.ca
FOR SALE; MURPHY REBEL KIT, Serial
#515. Wings and Empennage complete,also
Fuselage from Cabin back. All closure
inspections completed. Spring type Landing
gear. Reason for sale, lost Medical. Available in Edmonton AB. $12,000. OBO.Ted
Taylor,780 455-2524
ted.taylor@shaw.ca
Amphibious homebuilt Floats approx
1400'S in need of modification water tight
bukheads not watertight.with rigging for
installation 2 rudder config Floats too small
for my aircraft $6000.00 Larry Taylor 250492-0488 days ltaylor@pacificcoast.net
March - April 2012
The original Pegastol aircraft built
by the owners of Dedalius Aviation in 1997.
Aircraft is registered as an amateur built
aircraft @ 1200lbs gross weight and can be
flown with a ULP. Rotax 912S x 100 HP, with
slipper clutch gear box and 68" Warp Drive
Propellor. Engine has 20 hours on it since
coming back from Rotax (Tri-City) for starter
sprag clutch replacement. The gear box was
also overhauled considering it was on their
bench and was done as a precautionary
inspection considering it was already there.
New engine Barry Mounts upon engine
reinstall. New Custom aluminum main
fuel tank spring 2010. New windshield and
upholstery in 2009. Floats have Lake n Air
pump out cups (that are rarely needed as
floats are tight). 1/2" sound deadening foam
throughout cabin. Wheel gear and forks also
included. Airframe Total Time equals 620
hours, 912S Engine Total Time = 380 hrs,
Propellor Total Time = 532 hrs, Total Time
on Amphibs = 442 hrs. Has new $700 Heavy
Duty starter as well. LIMITED TIME ONLY
$42,000, so he can put that + winter storage
fees towards a 4 place.
For more details view at www.irishfield.
on.ca or send us an email oifa@irishfield.
on.ca
0320 E2C currently mounted on my Osprey
which could be included in sale. Osprey has
175 hrs since new engine has 1850 but was
dissassembled for a propstrike inspection
200 hrs ago Compression 125 lbs cyl on all
four jugs oil pressure good complete with
accessories. $6000 for engine $9000 for all aircraft needs refinishing and recover Larry
Taylor 250-492-0488 days ltaylor@pacificcoast.net
For Sale: 1997 Pazmany PL1. C-90 Cont.
Total Time: 220 hrs. (Airframe and Engine).
Side by side seating. Low wing, tip tanks (24
gals US total). Full inst. panel with mode
C. Always hangared. Pictures available.
$24,000.00 or Best Offer. Call: Ed at 204-6429485 or email: edira@mts.net Sep11
FOR SALE Teenie Two, completed in spring
of 2011 and has taxi time only. New Great
Planes 1835, icom handheld, beautiful construction. Registered as ultralight and currently hangared CYPQ. See the youtube
video at http://www.youtube.com/watch?
v=d89Gg0TvJ98 $5000. Owner deceased so
I am handling the sale. Contact Dave Smith
davecsmith2002@yahoo.com Sep11
Stits Skycoupe with O-290 125 hp, 240
hrs TT. Garmon 195, Escort 110, ICOM A5,
intercom, wing tanks. Located at Burlington
Ont CZBA. Must sell due to financial constraints. $16,900 OBO. 905-332-7331
9187 aero grinder M 92 with directions,
plus drill guide #d 92. This machine refaces
exhaust ports without removing cylinders
from thenengine. It has a drill guide for
removing broken exhaust studs on Continental and Lycoming engines. Air powered.
asking $800 647-298-4461 Toronto area.
Sep11
Aeronca Chief project, 1160 TT A and
E Original 65 Cont, McCauley metal prop
Interior, panel, instruments, refurbished,
new tires, New ELT, rejuvenated ceconite,
requires windshield, Work on wings and
assembly to complete. No runout on engine
shaft. $10,000 or offer. 416-431-2009 Sep11
Front portion of RV6 Tilt Type Canopy
new, covered with protective material. $60 or
offer. Misc chief and champ parts. Call for
details. 416-431-2009 Sep11
Champ fuselage, ribs, fuel tank, complete tail and numerous other parts $ 1000.00
. Sprint fuselage, spars, ribs, $ 1000.00 Bill
Donig 705-842-0801 Dec11
Skybolt fuselage with Marquart Charger cantilever U/C., tail feathers, rudder/
brake pedals, metal fittings, axles, wheels.
Offers. Bill Phipson #3954. Phone 416-4312009 Dec11
VW engine and many parts. Engine was disassembled after 10 hours for inspection and
is still open and appears to be in good condition. Engine has prop flange and one mag.
Ten boxes of parts include enough to assemble another complete long block engine.
Includes spare oil coolers, spare sidedraft
carbs, and there will still be parts left over.
Located near Hamilton ON w.brubacher@
sympatico.ca Dec11
Sportsman 2+2 Project for sale ; owner has
passed away. This is a nice four place supercub style amateur built suitable for short
field work or floats. Nicely welded fuselage is painted and almost ready for cover.
Wings are all aluminium structure and
almost ready for fabric .Most airframe parts
included . No motor, prop or instruments.
Call Richard 705-652-6307 $17,000. OBO Europa XS monowheel with Rotax 914
turbo engine and Airmaster constant speed
prop, 87 hrs total time. VFR panel with
Mode C transponder, KMG GPS, Becker
720 com with intercom and headsets. This
is a fast and efficient cross country aircraft
with low fuel consumption. Asking $65K, no
reasonable offer refused. Contact Hazel Peregrym at 250-672-5587 snowgoose@telus.net
For Sale: Zenith CH601XL , airframe 80%
complete, controls installed. Canopy mold. No landing gear. Subaru 2.2L no re-drive.
$3000 or best offer. Call 705 279 4399 or 519
351 6251
Many parts from Dave Johnson and Crossflow Subaru belt redrives including shafts
and prop flanges, bulkheads and separators, bearings in their housings, also starter
mounts, but no gears. If you are a national
member and you need parts and show up
on a Wednesday morning, they are free. If
they must be boxed and shipped there will
be a charge for this. garywolf@rogers.com
519-648-3030
Zenith TRI-Z CH300-1983. Lyc. O-320
Sensenich prop,ICOM 2000/intercom. Nose
wheel mod. Toe Brakes. Nav/Strobes/Bcn.
TT 273 $19,500. albanus@rogers.com 905686-7546
Zenith CH300 for sale First flight 1990 265
hours TT airframe and engine. Lycoming O320 E2D 150 HP engine professionally "zeroed" by Leavens aviation with all
documentation. New McCauley cruise prop
installed 3 years ago (cruise all day at 135140 mph on 8gph). Professionally painted
by flying colours in peterborough..$10,000.
New sliding tinted canopy installed 5 years
ago..flawless..with no cracks.
New interior installed top to bottom..seats..
doorskins..panel..dash ect. Full IFR steam
gauges. blue mountain EFIS light. 3 axis
auto pilot. True Trak pictorial pilot AP coupled to Garmin 396 to track a flightplan or
approach..super accurate. Truk Trak Altrav
VS altitude hold with verticle rate..aircraft
can be flown hands off from takeoff to shortfinal….trust me ive done it…..amazing
amazing unit!
Flo scan fuel management system computer
with opitical transducer….super accurate...
with fuel remaining...fuel used….endurance
for given power setting and of course fuel
flow.
King digital 720 radio. Narco mode C transponder with encoder. Ammeter and Volt
meter. 4 place intercom for front and back
seat headsets. Full lights inside and out for
night flying. New tires 2010.12 volt recepticals front seat and back seat for PAX. Reiff
full pre-heat system for winter operations..
(oil pan heat and cylinder bands for each
jug..very effective). Air Wolfe remote oil
filter system installed for 50 hour intervals
and added engine protection.
New Marvel carb installed 2007. All builders logs and plans..complete journey and
tech logs..all owners manuals and professionally produced POH documenting every
aspect of aircraft operations as well as placarded checklists. Always maintained to
highest standards…$ 35,000….(certified and
e-tested!!). I would have no qualms selling
this aircraft to anyone…..a joy to fly. Warren 289-259-6460
Cavalier 102.5, "Aero Sport Power" O-320B2B; 152 TTSN. Sensenich metal prop. Airframe was totally rebuilt in 1997; 1750#
GW, 622 lb useful load; VFR instruments +
Garman GTX 327 TXP Mode C & Val Radio;
Trutrak Turn & Bank; Kept in heated hangar;
8/10 inside and out. $29,000 OBO. cavalier102@uniserve.com or 250-558-5551. Ask
for Cameron.
O-235 Experimental TSO-87, smooth 3 blade
Warp 77-since new, mags 77hrs, carb70hrs,
high compression pistons, presently on
aircraft. Runs great, upgrading to O320.
Ask$12000. Jamie Richarjs@xplornet.com
Ads run for a maximum three issues depending
on space available and then must be renewed
for continued display. Please direct all classified
inquiries and ad cancellations to: raa@raa.ca and
place “RAA ad” in the subject line.
Send us Photos of your completed projects
Share your accomplishment with others - you've earned it! Please include a brief description of your aircraft and any other details you want to
include, and send us a colour print with it. Mail to: Recreational Aircraft Association of Canada 13691 McLaughlin Road, R R 1, Caledon, Ontario
L7C 2B2...or email us the information and a high resolution digital picture (jpeg format please) to: raa@zing-net.ca
March - April 2012
Kaspar Naef's Rans S-7
A Turbo'd Geo Engine helps with mountain operations
There is always a lot of talk about
auto engine conversions and not
much actual building or flying. By
contrast Kasper Naef of Nelson BC
has built and flown several Geo
engine combinations for his modified
Rans S-7 Basic Ultralight floatplane.
In 1997 he began with a turbocharged
1 litre Geo three cylinder engine and
an early Raven HTD belt redrive. The
power was good but high temperatures were always bothersome. Later
March - April 2012
the Geo G13BB four cylinder 1300 cc
engine with single cam and 16 valves
became available, so Kasper modified the redrive to fit this engine and
began flying behind it in 2005. The
result was about the same power as
the 1 litre turbo engine but without
the cooling problems
Kasper next added a Garrett T
25 turbo to this engine and it took
nearly two years to get everything
sorted. One major improvement was
the installation of the Simple Digital
Systems engine management system
from Calgary AB. www.sdsefi.com
This system made it possible to dial
timing and mixture in properly. With
the firewall of the S-7 being only 24"
wide and 26" tall it was a challenge
to fit the oil and water rads plus the
intercooler inside the cowling and
still get rid of the heat radiating
from the turbo but he did succeed in
this. Kasper now has 200 hours on
this engine and turbo combination
and everything works well. With the
Czech amphib floats his cruise speed
is just over 100 mph at 31" manifold
pressure (~1 pound of boost). Above
9000 ft the true airspeed of the S-7 is
125 mph.
Climb is 1000 fpm at 35" MP and
the wastegate is set to a very conservative 38" limit. Takeoff rpm is 5200,
and with everything pushed forward
in level flight the engine turns 5700.
Normal cruise is around 5000 rpms at 4.5 to 5 gph.
Kasper Naef's current project
is a Rans S-6 that he is building for
the Amateur Built category. He has
again chosen the G13BB Geo engine
but this time it is fitted with the SPG gearbox from Airtrikes in Quebec
(www.airtrikes.net). Because of the
short offset between crank and output
shaft he has laid the engine over to be
able to raise the thrust line. The turbo
is rather low and it is necessary to
have its oil drain by gravity so he has
built a new sump below the engine.
The stock geo oil pump handles
all lubrication and test runs with a
clear oil pickup tube show immediate
pickup from the low sump.
Kasper is again using the T 25
turbo and SS engine management
system as they have been proven on
his S-7. A video of the engine running on the test stand may be seen at
http://youtu.be/lq6z0_ep9q4
Above: Despite the tall inline engine the cowling has pleasing
lines. Louvers assist in removing turbo heat.
Upper left: The rad, oil cooler, and intercooler are well
packaged with the belt redrive.
Lower left: The fabricated exhaust manifold feeds the Garrett
turbo which is itself an effective exhaust silencer.
CAP AVIATION SUPPLIES
HOMEBUILDER SUPPLIES
4130 TUBING & PLATE
ALUMINUM SHEET
2024T3 & 6061T6
AN,MS, NAS HARDWARE
CONTINENTAL & LYCOMING PARTS
148 OXBOW PARK DRIVE,
WASAGA BEACH, ON
PHONE: 705-422-0794
Digital page design that works right.
Brochures
Newsletters
Branding
Copy Writing
Web Pages
SPORT PLANES & ENGINES
CanadianDealers
SEE OUR WEB SITE: www.jabirucanada.com
Email: info@jabirucanada.com Tel. (613) 347-3155
Fax. (613) 347-3074
George Gregory
Pagemeister
604-773-0035
george@sidekickgraphics.com
http://SideKickGraphics.com
National Aviation
Insurance Brokers
Bill Davidson of National Aviation Insurance
Brokers handles the RAA Chapter Liability Policy and he
also offers all types of insurance that many of us buy
to cover our cars, homes, aircraft, and hangars. He has
very attractive prices on the hangar coverage required
by many airports and landowners. Here is an example:
Hangar Coverage ALL RISK / Broadform
Hangar Building $100,000...................Premium $280
Deductible ..................................................... $1,000
Liability $1,000,000.00........................Premium $150
Total Premium.............................................. $430.00
Subject to Underwriting
National Aviation Insurance Brokers Ltd
Insuring the BEST PILOTS in Canada
Phone: 905-683-8986 / 1-800-463-0754
Fax: 905-683-6977 / 1-866-683-6977
email: bill@jsdavidson.ca
raa.ca
Classifieds On The Internet:
http://www.ocis.net/tvsac/buyandsell.html -more ads from our Kamloops chapter
http://www.lyncrest.org/sfcclassifieds.html -more ads from our Winnipeg chapter
tech articles • forum • news • upcoming events • contact info and links
March - April 2012
















Everything
for Airplanes!
Composite Materials
Wood Products
Metal
Hardware
Airframe Parts
Landing Gear
Engine Parts
Polyber / PTI Paints
Instruments
Batteries / Chargers
Electrical
Avionics / GPS
Headsets / Intercoms
Tools
Books / DVDs
FREE
F
REE
2010-2011 800+ pg. Parts Catalog,
also on CD, and full color
Pilot Shop Catalog!
1-877-4SPRUCE
7 7 7 8 2 3
info@aircraftspruce.com
Store Hours:
Monday - Friday
8:00am to 5:00pm
Saturday
8:00am to 3:00pm
AIRCRAFT SPRUCE CANADA
(CYFD)
150 Aviation Avenue
Brantford Municipal Airport
Brantford, ON N3T 5L7
Ph: (905) 795-2278
(877) 795-2278
www.aircraftspruce.ca
March - April 2012

April - The Recreational Aircraft Association

Transcription

Similar documents

Wherever you are. Whenever you need it.

brochure - Aliserio – Bizjet Maintenance

Airvan8 Brochure

Loftleidir-Icelandic

engine tYpe 912 | 80 hp (UL/a/F)

proudly offers FOR SALE 1976 Beechcraft Baron 58

Fat Albert - California Capital Airshow

The Flyer - BMFA Scale Technical Committee

201501 CONTACT January