Uni Black Box – Manual

Transcription

Support and Docs: UniBlackBox.com
Uni Black Box – Manual
version 1.0.0
Caution! - Please read last page!
Important safety message!
Do not use UniBlackBox unless You will read and understand this manual.
Introduction
Uni Black Box is complex device designed for servicing cellular phones.
It's All-in-One device that contain:
1) UniBox with Fbus transmission.
2) Nokia Griffin Box - service for all Nokia phones.
3) SonyEricsson DIV - for new SonyEricsson phones.
4) Sagem Code Reader – for unlocking Sagem phones.
5) USB hub - You can connect any USB device.
6) Extension socket – lets You to Upgrade Your UBB
In Set:
Photo
1. Manual
2. Uni Black Box
3. Main Cable
4. Fbus cable set
5. Griffin cable set
6. DIV cable
7. Sagem Code Reader
cables
Basic details
Switches and LEDs.
Front of UBB
1) SWITCH DEVICE. Use this switch to change active device.
After Power ON the box – Fbus is set as default.
2) USB Socket. You can connect any USB device.
3) Fbus. Work with most popular mode, this mode can be used simultaneously with any other
mode. Software recommended for this mode is Universal Simlock Remover - included
with Uni Black Box.
LEDs signaling:
1.In COM mode(switch on back panel):
a – RX.
b – only Fbus is active.
c – TX.
2.USB mode:
a – RX.
b – ON – only Fbus is active.
BLINKING – VCP in use.
c – TX.
4) Griffin. Uni Black Box works as Griffin Box. Use it for NOKIA phones.
LEDs signaling:
d – Phone supply voltage ON
e – Griffin Mode active
f – blinking – Device works fine.
5) DIV. Uni Black Box works as Sony Ericsson DIV.
LEDs signaling:
g – DIV Mode active
6) Sagem Code Reader. Unlock Sagem phones.
Note: This socket is shared with ADD (addition socket)
LEDs signaling:
h – SCR Mode active
7) Add. This mode can be activated only if extension is plugged into extension socket .
Devices from side socket share RJ45 socket with SCR.
LEDs signaling:
i – Add mode active.
Back of UBB
1) Power connector. External power supply IS NOT necessary. UBB is powered from USB
port. Optional external power supply should be: 8-9V 300-500mA, '+' inside.
Note: External power supply is needed ONLY when some problems with Griffin appears.
2) DB 25 – data cable connector.
3) USB Socket – Indispensable power supply, overcurrent protection and data for fast Fbus
VCP (Virtual COM Port) mode.
4) Fbus mode switch:
a) Switch up – fast VCP (UBB USB<->Fbus) Virtual COM.
b) Switch down (as on drawing) – Hardware COM.
Cable set description and safety measures.
1) Cable Set
Package contains:
1) Set of 70 cables to work with fbus mode. Allow to work (simlock, language, repair) with
many phones for example Siemens phones from x25 up to x6x models.
2) One cable for SonyEricsson phones.
Cable works with DIV LPT5 software an allow full service of SonyEricsson:
1. A3618s, A2618/A2628, A2218
2. P800/P802, P900/P908
3. R520, R600
4. T20/29, T39, T65, T68
5. T100/T105/T106
6. T200/T202, T226/T237, T230/T238
7. T300, T310/T312, T316
8. T610/T618, T616, T630/T628, T637
9. Z200/Z208
10.Z600/Z608
3) Over 40 cables for use with Griffn.
Allow full service of Nokia phones.
4) 2 cables for SCR(Sagem).
Allow Unlock Phone by reading codes.
5) Main cable.
6) USB cable.
Additional cables and accessories – buy on our web page.
WRNING!!!|
To each socket specific cables designed. Using wrong cables may destroy Uni Black Box.
With Griffin socket use only cables with this sticker:
With DIV socket use only cable marked as SE DIV
With SCR socket use only 2 cables with 4 testpoint wires
2) Switching to desired operating mode
To switch between modes use SWITCH DEVICE key.
1) Fbus. For majority of phones. Service: unlock, repair, language change, flash.
2) Griffin. Use only with Nokia phones. Service: unlock, repair, language change, flash.
3) DIV. Use only with SonyEricsson phones. Service: unlock, repair, language change, flash
4) SCR.Use only with Sagem phones. Service: unlock.
5) Add. For additional devices, can be activated only when device is plugged into side socket.
3) Safety measures
•
•
•
•
•
•
•
Always use power supply from USB.
Before You connect any cable, make sure You are using correct cable.
Don NOT use cables not included in package.
Do NOT use other external power supply than described in this manual.
Do NOT connect high voltage.
Keep box away from water. (if box get wet, dry it well before connect any cable)
Uni Black Box Works with Windows XP and 2000. Recommended OS is Windows 98. In
other OS some modes may work incorrectly.
Unlocking, Flashing...
Connecting to PC.
Use only cables supplied with Uni Black Box.
Drivers and Software Setup.
Drivers setup
Drivers are required to operate with VCP Fbus mode.
1) Connect USB cable.
2) ”Add New Hardware Wizard” will start automatically. Click “Next >”
3) Choose “Search for the best driver...” and click “Next >”
4) Check “CD-ROM drive” or “Specify a location” (if driver is on other location) and click
“Next >”
5) When driver is found click “Next >”
6) Next screen - click “Finish”. Done.
Port Configuration
•
Go to Control Panel ->System
Switch to “Device Manager”
Explode group“Ports(COM& LPT)
Double click on “UBB USB<->Fbus”.
•
Click “Advanced...”
•
•
•
•
•
If necessary, set required Com number (Most software included in USR supports
COM1...COM4)
Set other setting like below.
Software setup.
For Uni Black Box we have prepared:
Universal Simlock Remover, Install from included CD or download from support web.
Nokia Griffin Box- manual.
To use Griffin Box You have to install software from included CD or downloaded from
website.
List of equivalent cables.
1100-2300-2600
2100-3610-5210-8210-8850
2650
3100-6100
3210
3220-7260
3310-3330-3410-3315-33505510
3300
3510-3510i-3530
3650-3660
5100
5110-5110i-6110-6150-62106250-7110
5140
6170-7270
6230
6260
6310-6310i
6610-7210-7250-7250i-32006220-6610i
6500-6510-8310
6620
6630
6650
6800-6810
6820
7200
7280
7600
7610
7650
8910-8910i
9210-9210i
9500
N-Gage
N-GageQD
After install (some phones requires Flash Update installation too), on your desktop a new icon
“Griffin Nokia” will appear - double click on it when Uni Black Box is switched to Griffin
and no phone is connected (sometimes the phone may have too big power consumption).
You should see “ACTIVATED BOX” message.
To change language (unlock) in NOKIA DCT3 (example 3410):
1.
2.
3.
4.
Download and install correct flash files pack.
Start Griffin software.
Connect phone with correct cable.
Check “DCT3 Phone”
phone will auto power on
note: if phone will not power on automatically
disconnect the phone, close Griffin program and got point 2 (try also reboot PC).
5. Click “Detect Phone”
6. Choose from list correct files pack.
7. If numbers in marked areas are the same uncheck ”MCU”
8. Click “Flash” and wait until You see this text
9. To unlock DCT3 NOKIA, click “Unlock” after step 5
To change language(unlock) in NOKIA DCT4 (example 3510):
1.
2.
3.
4.
5.
Download and install correct flash files pack.
Start Griffin software.
Power on the pone and click “Detect Phone”
Choose from list correct files pack
6. If numbers in marked areas are same uncheck ”MCU”
7. Click “Flash” and wait for this text
8. Now phone have MCU and PPM in 5.02 version.
9. To unlock, click “Unlock” after step 4.
Other functions (ex. Nokia 6600):
•
Power on phone and click “Detect PHONE”
click “serial >>”
From Features menu choose: Phone BB Tests(Self Test)
Click “Execute”
•
Results can be scrolled with this buttons.
•
•
•
•
More details in manual for Griffin box.
SonyEricsson DIV – manual
For older Ericsson phones use Fbus mode, for newer pones You need DIV interface and
special (SE DIV) cable.
OS: Recommended: Windows 98. Works also on: XP and 2000.
•
Connect UBB to PC with main cable and USB cable
•
•
Press SWITCH DEVICE button on UBB until DIV mode is set
Run USR software
Run “DIVLPT 5” software by clicking on START button
Connect phone using “SE DIV” cable
•
Phone must be OFF
•
•
•
Choose phone model from list
•
To change phone firmware switch to “Flash”
Check “Flash AVR CPU” , “Flash ARM CPU” or “Write GDFS file”
Choose file and click “Do Selected Jobs”
Wait until finish
•
•
•
•
To unlock switch to “Unlock”
Check some jobs to do (“Read ALL Codes” or direct “Clear SP Locks”)
•
Click “Do Selected Jobs” and wait until finish
•
WARNING! IMEI change is illegal!
How to enter read codes:
•
•
•
•
Insert SIM card
Power on the phone
Pres on phone keyboard <**< (“<” is cursor in left)
This way you will access “Personalization” menu
Choose “NET” and enter NCK code
More details in manual for DIV
Sagem Code Reader – manual
OS: Recommended: Windows 98. Works also on: XP and 2000.
•
Connect Box with main and USB cable
Press SWITCH DEVICE until SCR mode will be activated
Run USR software
Run “Sagem Code Reader v14” software by clicking START
•
Connect phone to UBB
•
•
•
Connect plug into sagem phone and soldier testpoints into sagem board like shown
below
If You have problems soldiering to Sagem board You can buy Sagem additions – It is
not in set.
•
Choose phone model
•
Click “Read Code”
•
Phone Code (User Code) is displayed in 5-th line from top – right here
How to enter the unlock code:
•
power on the phone with locked SIM card
enter unlock code from last line (without “-”)
•
Troubleshooting
“Phone NOT FOUND” You must check if:
1. Battery is well connected and fully loaded
2. Phone is turned ON
3. C2 or 9xx connector is correctly connected to the phone
“Bad connection” Check if:
1. Testpoint wires are correctly mounted!
2. C2 or 9xx connector is correctly connected to the phone
Fbus – manual
This socket is for most phones. It's most popular interface for communication.
All You have to do is install Universal Simlock Remover and look at SOFTWARE and
DOCUMENTATION sections - there is description of the software and how to use it.
Example
Example of use with LG8120 and “Lg Workshop By Vygis” software (This software is NOT
free)
•
Connect phone with cable marked as LG8110.
(On the photo You may see usage of USB hub. Vygis key connected.)
1. Choose COM port which You want use.
If You are using “UBB USB<-> Fbus”port, switch UBB into VCP fbus mode.
2. Set transmission speed. Note that speeds above 115200 kb/s are available only for VCP
Fbus mode.
3. Choose phone model.
4. Click “Connect”.
5. In tab “Unlocker” You can unlock your phone.
6. In tab “U81xx” You can lock your phone (Relock PHONE) or read GDFS (Read GDFS)
Warning!
Uni Black Box is set of cables and devices.
This manual describes how to use it.
If You are doing everything carefully there will be no troubles.
But always there is a risk of incorrect unlock or flash write/read.
Everything You do on Your own risk..
Change IMEI is illegal!

Uni Black Box – Manual

Transcription

Similar documents

silly cable tech terms

www.vecsupply.com

ES14-OTDR

B1557601-EXI-0005 to 0006 – Public Utilities

Ebeco winter products

ses center arc cable antenna program

AccuBoom™ Case IH SPX 3310 CAN Installation

Untitled - DML Audio

the Merger Welcome Kit

SAGEM F@st 240x SAGEM F@st 244x

nVidia Hardware Documentation