NetProbe Lite

Transcription

NetProbe Lite

NetProbe Lite
Web Based 8 Channel Sensor Collector
User Manual
Version 1.2
Copyright Information
Copyright © 2004-2005, Mega System Technologies, Inc.
All rights reserved.
Reproduction without permission is prohibited.
Technical Support and Contact Information
Mega System Technologies, Inc.
Tel: +886-2-87922060
Fax: +886-2-87922066
Web: www.megatec.com.tw
Customer Service: service@megatec.com.tw
CONTENTS
Chapter 1: Introduction ________________________________________ 1
Section 1. Features___________________________________________ 1
Section 2. Networking with NetProbe Lite _________________________ 2
Section 3. Package Contents ___________________________________ 2
Section 4. NetProbe Lite Description _____________________________ 3
Section 5. NetProbe Lite DB-9 Pin Assignment _____________________ 3
Section 6. NetProbe Lite Indicators ______________________________ 4
Chapter 2: Installation Procedure ________________________________ 5
Chapter 3: NetProbe Lite Installation _____________________________ 6
Section 1. Installation Procedure ________________________________ 6
Chapter 4: Using Netility to Setup IP & Update Firmware________________ 8
Section 1. Installing Netility _____________________________________ 8
Section 2. Using Netility _______________________________________ 8
2.1 Network Selection _________________________________________ 8
2.2 Configure _______________________________________________ 9
2.2.1 IP Address_____________________________________________ 9
2.2.2 Advanced ____________________________________________ 10
2.3 Upgrade Firmware _______________________________________ 10
2.4 About__________________________________________________ 11
2.5 Refresh ________________________________________________ 11
Chapter 5: NetProbe Lite Web Manager __________________________ 12
Section 1. Introduction _______________________________________ 12
Section 2. NetProbe Lite Web Manager Interface __________________ 12
2.1 Information _____________________________________________ 13
2.1.1 System Status _________________________________________ 13
2.1.2 Current Status _________________________________________ 14
2.2 Configuration____________________________________________ 14
2.2.1 NetProbe Properties ____________________________________ 14
2.2.2 Network______________________________________________ 16
2.2.3 SNMP _______________________________________________ 19
2.2.4 Email ________________________________________________ 21
2.2.5 WEB ________________________________________________ 24
2.2.6 System Time __________________________________________ 25
2.3 Log Information __________________________________________ 27
i
2.3.1 Event Log_____________________________________________ 27
2.3.2 Data Log _____________________________________________ 28
2.3.3 Save Data Log _________________________________________ 28
2.4 Help___________________________________________________ 29
2.4.1 About NetProbe ________________________________________ 29
Appendix A: Methods to Update NetProbe Lite Firmware ___________ 31
ii
Chapter 1: Introduction
Section 1. Features
NetProbe Lite is designed to collect output from equipment or devices. This output
can either be dry contact alarm signal or analog signals for remote monitoring and
management systems. These are all important data within a complex enterprise
network.
Some of the main features of this device are;
Firmware:
• Built-in Web Server
• Configuration via telnet, Web or Netility (freeware)
• PPPoE and DDNS protocol for xDSL broadband connection
• Allow Up to 8 User Accounts and Passwords
• Support Any Java-Enabled Web Browser
• Supports PDA, GPRS and WAP for GSM phone.
• Network Protocol: HTTP server, TCP/IP, UDP, SMTP, PPPoE, DDNS, DNS
Client, SNTP, BOOTP, DHCP, Telnet, FTP, SNMP TRAP, PDA, WAP/GSM
Hardware:
• Built-in temperature and humidity sensor.
• Temperature detection range: -40°C to 100°C
• Humidity detection range: RH 0% to 100%
• Support 8 channels for Voltage input or 4 channels for dry contact input.
• 0V to 4.096V detection range in 8-bit / 10-bit / 12-bit resolution.
• Individual voltage mode. Voltage detection of Sig-1 to Sig-8
• Voltage difference mode: Voltage difference detection of (Sig-1 – Sig-2),
(Sig-3 – Sig-4), (Sig-5 – Sig-6), (Sig-7 – Sig-8).
• LCD display shows the IP address, Subnet Mask, Gateway and Status or
Voltage or individual channel sequentially.
• 32-Bit 50MHz RISC ARM7 CPU
• System clock: 25MHz or 50MHz
• Flash Memory: 512KB / 1MB / 2MB / 4MB / 8MB
• Dynamic Memory: 2MB / 8MB / 16MB
• Power supply: 4.8V to 7.0V DC, 250mA maximum.
• Operating Voltage: 3.3 volts
• Operating Temperature: 0°C ~ 50°C
• Operating Humidity: 5% ~ 90%
• Dimensions: 48mm x 63mm x 21m
• Weight: 75g
NetProbe Lite User ‘s Manual
-1-
Section 2. Networking with NetProbe Lite
With NetProbe Lite, the data in either analog voltage inputs (up to 8 devices) or dry
contact digital inputs (up to 4 devices) can be collected and broadcast over the
Internet or LAN. These data can then be translated by a MIB and managed using
SNMP NMS over HP OpenView. Alternatively, the user can use a web browser to
view and monitor these devices from the NetProbe Lite web page.
Fig.1 NetProbe Lite Network diagram
Section 3. Package Contents
A standard package should contain these items;
One NetProbe Lite module
One Utility CD which contains;
1. Netility: to configure IP address and update the firmware.
2. Time Server: Time adjustment utility.
3. Adobe Acrobat 5.0 Reader.
User Manual
One Power Adaptor (European / USA)
-2-
Section 4. NetProbe Lite Description
Fig.2 NetProbe Lite Front View
Section 5. NetProbe Lite DB-9 Pin Assignment
Fig.3 DB-9 Male
NetProbe Lite DB-9 PIN Assignment
Male DB-9
Pin No.
1
2
3
4
5
RS-232
Sig-1
Sig-3
Sig-5
Sig-7
GND
-3-
Sig-2
Sig-4
Sig-6
Sig-8
6
7
8
9
Fig.4 NetProbe Lite DB-9 PIN assignment
NOTE: Due to the variety of available device, the user will have to modify the
connector to suite their purpose.
Section 6. NetProbe Lite Indicators
NetProbe Lite LED Status Indicators
Color
Green
Red
Yellow
Signal Definition
Condition / Description
Power state
On: Normal power
Error Condition
On: Error condition occurred
Data activity
Flash when there is data detection
on DB-9 signals. When there is a
user logon, the Yellow LED will be
ON for 30 seconds.
Fig.5 NetProbe Lite Status LED Indicator
NetProbe Lite LAN Port LED Light indicators
Color
Condition / Description
Green
On: Internet correspond speed is 100M
Flash: Data transmitting / receiving
Yellow
On: Internet correspond speed is 10M
Flash: Data transmitting / receiving
Fig.6 NetProbe Lite LAN LED Indicator
-4-
Chapter 2: Installation Procedure
Chapter 2: Installation Procedure
Before you start using NetProbe Lite, you will need to set-up both the hardware and
software. The following is a flow chart on the installation procedure:
Connect the designated serial device, power
adaptor and Ethernet cable to NetProbe Lite
(Chapter 3)
Install Netility supplied in the Utility CD.
Use Netility to setup the IP (for Static IP)
(Chapter 4)
Open a standard web browser, key in the IP
and go thru the configuration in
“NetProbe Lite Web Manager”
(Chapter 5)
Set-up completed
Fig.7 NetProbe Lite UPS installation flowchart
-5-
Chapter 3: NetProbe Lite
Chapter 3: NetProbe Lite Installation
The following details the installation procedure for NetProbe Lite.
Section 1. Installation Procedure
Step 1:
Connect the individual
DB-9 pin to the device to
be monitored.
Step 2:
Connect one end of the
Ethernet cable to a hub /
router.
-6-
Chapter 3: NetProbe Lite
Step 3:
Connect the other end of
the Ethernet cable to
NetProbe Lite Ethernet
port.
Step 4:
Connect the DC adapter
power
output
into
NetProbe Lite socket,
and plug the DC adaptor
into the wall socket
Step 5:
The LCD will display the
IP,
Subnet
Mask,
Gateway, the current
temperature
and
humidity.
Enter the shown IP
address into a standard
WEB browser to login
into NetProbe Lite web
manager.
WARNING:
Please make sure the input Voltage and Frequency of the DC power adapter
(DC 5.3V) is correct before plugging into the power outlet.
-7-
Chapter 4: Using Netility to Setup IP & Update Firmware
Section 1. Installing Netility
1. Insert the Utility CD into the CD-ROM drive and execute Netility.exe
2. After installation is completed, ‘Netility’ group will appear in Windows ’Start’ Æ
‘Program Group’.
Fig.8 Netility Group
3. Click “Netility” to start the program.
Section 2. Using Netility
The Netility main menu is shown below. The selection menu is located on the left. The
device, hardware, firmware and IP address connected to a LAN are displayed on the
right.
nSelect Network card in you system
o Configure NetProbe Lite
p Update NetProbe Lite
Firmware
q About Netility
r Conduct another search for
NetProbe Lites on network
Fig.9 Netility Main Menu
2.1 Network Selection
Once Netility starts-up, it will automatically search for the computer’s Network card (If
not, click on “Network Selection” on the main menu to start the search). A pop-up
window will show the available Network Adapter.
Next, select the Network Adapter, which is connected to the LAN, and click ‘OK’ to
return to the main menu. NetProbe Lite will now appear in the main menu display
area.
-8-
Fig.10 Netility: Network Selection
2.2 Configure
Select NetProbe Lite on the right display screen, and then click “Configure”. This will
bring up the IP Address Configuration window. Here, the user can set;
• IP Address
• Advanced (for port setting configuration)
2.2.1
IP Address
This section sets an IP Address for NetProbe Lite. Enter your IP Address if you have
a Static IP otherwise choose Obtain an IP address by DHCP.
Fig.11 Netility: Set an IP Address for NetProbe Lite
Once the IP address is set, you will be able to connect to the NetProbe Lite webpage
from a standard browser.
Obtain an IP address by DHCP or BOOTTP – the IP address, Subnet Mask and
Gateway is acquired automatically by the system.
-9-
2.2.2
Advanced
In order to increase security of NetProbe Lite, Netility offers two additional security
features:
i.
Netility Password
Use this to set an access password for Netility.
WARNING:
Do not lose this password. If the password is lost, Netility will not be able to
perform future firmware upgrades.
ii.
Management Protocol
(This function is disabled for NetProbe Lite)
2.3 Upgrade Firmware
Netility offers a convenient firmware upgrade. To upgrade your firmware follow the
following procedure.
Download the latest firmware;
1. Open internet explorer and browse to;
http://www.megatec.com.tw/CustomerService/Download/csdownload.htm
Make sure that you choose “NetProbe Lite” (Downloading the wrong
firmware may permanently damage NetProbe Lite).
2. Check if the latest firmware has been released.
3. Click
to download and save the file to your local hard drive.
Upgrade NetProbe Lite firmware;
1. Open Netility,
2. Click “Download Firmware” from the Netility main menu,
3. Click
, and browse to the location where you save the firmware.
4. Select the new firmware file (*.bin) and,
5. Click “Start”.
Fig.12 Netility: Update NetProbe Lite firmware
NetProbe Lite red and yellow LED will flash alternately to indicate that firmware
upgrading is in progress. Once completed, NetProbe Lite will reboot.
-10-
Note: If the downloading / upgrade process is interrupted or the data is
corrupted, NetProbe Lite will keep its default firmware to avoid complete data
loss. If this happens, repeat the above firmware upgrade procedure.
2.4 About
This section displays the current Netility version.
Fig.13 Netility version examined
2.5 Refresh
Normally, Netility will automatically search for any NetProbe Lite connected to the
LAN. However, the user can do a manual search by click the “Refresh” icon.
Fig.14 Netility: Manually search for NetProbe Lite
-11-
Chapter 5: NetProbe Lite Web Manager
Section 1. Introduction
After you have setup the hardware and set an IP address for NetProbe Lite, you will
then be able to go to NetProbe Lite web site to monitor, manage and control the serial
devices. All you have to do is enter the new IP address into any standard web
browser.
To do this;
1. Start the Web Brower (Netscape or Internet Explore)
2. Enter NetProbe Lite IP Address that was set earlier using Netility (e.g.
211.21.67.51) and press [ENTER]
Fig.15 Enter NetProbe Lite IP address
3. A login screen will appear, press [ENTER]. By default the username and
password is left blank.
Fig.16 NetProbe Lite Login screen
Section 2. NetProbe Lite Web Manager Interface
NetProbe Lite webpage main menu is divided into two sections. The selections menu
on the left and display menu on the right. The selection menu consists of the following
options:
2.1 Information
2.2 Configuration
2.3 Log Information
2.4 Help
-12-
2.1 Information
Click “Information” to open up the following sub-menu;
2.1.1 System Status
2.1.2 Current Status
Fig.17 NetProbe Lite Information Menu
2.1.1
System Status
Click on “System Status” to display the System Information and Network Status. The
information and values here are either provided by NetProbe Lite or were set by the
users in the “Configuration” section earlier on.
i.
System Information
This section shows NetProbe Lite System Information such as the Hardware and
Firmware Version, the serial number, current / local System Time, the system
name, contact, location, uptime and Signal Detection Type. These values are
either provided by NetProbe Lite or set by user earlier.
ii.
Network Status
This section shows NetProbe Lite Network settings. The MAC address is unique
to every NetProbe Lite. All the other values are set by the user in the
Configuration page.
-13-
2.1.2
Current Status
The Current Status displays information collected by NetProbe Lite. Such as
Temperature, Humidity and data from each connected device.
By default the Refresh Status is set to 10 seconds. Choose between; 2 seconds, 5
seconds, 10 seconds, 30 seconds and 1 minute.
Fig.18 NetProbe Lite Current Status Menu
2.2 Configuration
Please ensure that each of the following option is set correctly. Otherwise, NetProbe
Lite may not work properly.
2.2.1 NetProbe Properties
2.2.2 Network
2.2.3 SNMP
2.2.4 Email
2.2.5 WEB
2.2.6 System Time
2.2.1
NetProbe Properties
This section determines the types of signal to be detected and their detection
parameters.
i.
Type
There are four (4) different Signal Detection Types available.
Signal Detection Type
8-Analog input
4-Differential Signal Input
Description
For detection 8 individual analog signals. Signal
detection range from 0 v to +4.096 v
For detection 4 differential analog signals. Signal
-14-
(Bipolar)
4-Differential Signal Input
(Unipolar)
4-Contact Closure Input
ii.
detection range from -2.048 v to +2.048 v
For detection 4 differential analog signals. Signal
detection range from 0 v to +4.096 v
For detection 4 contact closure signals. Signal
detection of either opened or closed state.
Critical Value
Enter in the minimum and maximum Temperature / Humidity detection range.
Temperature
Set the temperature range between -10 C to 100 C.
Humidity
Set the humidity range between 0 to 100%.
If the temperature drops below the minimum set value or over the maximum value,
a TRAP will be sent.
iii.
Analog / Bipolar / Unipolar Detection Setting
Caption
Group
Caption
Factor
Unit
Min
Max
iv.
Description
Group number, corresponding to “Sig” grouping.
Enter a suitable name for this group signal.
The factor needs to multiply on the signal voltage
detected.
The Unit of the signal.
Set the minimum value (0V)
Set the maximum value (4.096V)
Contact Closure Detection Setting
-15-
Enter a suitable name for the group signal (Maximum of 31 characters)
v.
Data Log
Record Data Every
Use this option to determine the record interval.
minutes, 30 minutes, 1 hour or None.
2.2.2
Choose between; 1 minute, 10
Network
This option determines NetProbe Lite Network settings.
i.
IP Address
Fig.19 NetProbe Lite IP Address Settings
IP Address
If you want to fix the IP address, enter your chosen IP address here.
go to “Obtain an IP address” and choose “via DHCP”
Otherwise
Subnet Mask
This item sets NetProbe Lite Subnet Mask. The value is normally 255.255.255.0
Gateway
This item is to set NetProbe Lite Gateway.
Obtain an IP address
The IP address can be set;
a. By manually
b. Using DHCP, or
c. Using Bootp
NetProbe Lite will reboot after the above settings have been changed.
ii.
DNS Server IP
-16-
Fig.20 NetProbe Lite DNS Server IP
Primary DNS Server IP
This item sets NetProbe Lite primary DNS Server IP address.
if you have a DNS Server IP.
Enter a value here
Secondary DNS Server IP
This item sets NetProbe Lite secondary DNS Server IP address. NetProbe Lite will
use the secondary DNS Server IP address if the Primary DNS Server IP address
is not working.
iii.
Ethernet
Fig.21 NetProbe Lite Ethernet Settings
Connection Type
This item sets the communication speed between NetProbe Lite and the Network.
Choose “Auto Sense” to let NetProbe Lite automatically decide on the appropriate
connection speed. Alternatively you can manually choose either;
• 10Mbps Half-Duplex
• 10Mbps Full-Duplex
• 100Mbps Half-Duplex
• 100Mbps Full-Duplex
NetProbe Lite will reboot if this setting is changed.
iv.
Dynamic DNS
Fig.22 NetProbe Lite Dynamic DNS Settings
Service Provider
For users with a Dynamic IP, NetProbe Lite can be configured to point the current
IP (as provided by your ISP upon each successful dial-up to the internet) to a
dynamic DNS provider. This will enable you to locate NetProbe Lite every time
the IP changes due to an ADSL connection redial.
-17-
To enable this function, you will first have to register with either one of these three
service providers;
• None (Choose this only if you have a Static IP)
• 3322.org
• dhs.org
• DynDNS(Dynamic)
• DynDNS(Custom)
• Myddns.com
• Zive.org
Domain Name
Enter the Domain Name you have created from one of the three websites.
Login Name
Enter your login name for the above domain name.
you register with the above DDNS provider.
Login Password
Enter your password.
DDNS provider.
You should have this when
You should have this when you register with the above
Use external STUN server to get Public IP to register
Enable/disable using the external IP for DDNS server registration. If this function
is enabled, the NET101 will get the external IP by the help of STUN server, and
then use this IP to register the IP of the DDNS server.
Primary STUN Server IP
Input the primary STUN server IP. The NET101 will use this server’s help to get
the external IP address. The default IP is 66.7.238.210.
Secondary STUN Server IP
Input the secondary STUN server IP. The NET101 will use this server’s help to get
the external IP address when the primary STUN server has no respond. The
default IP is 67.153.142.67.
v.
PPPoE
Use this option to allow NetProbe Lite to connect to the internet using your xDSL
modem. Once set-up, NetProbe Lite will be able connect to the Internet directly
without going thru a PC.
Fig.23 NetProbe Lite PPPoE setting
When Connection should be made
-18-
The user has a choice of;
Disabled
: Default setting.
Connect always
: NetProbe Lite will automatically dial up the ISP.
Login Name
Enter your login name as provided by your ISP.
Login Password
Enter your password as provided by your ISP.
2.2.3
SNMP
This page is to set the SNMP settings so it can be used by a NMS (Network
Management System).
i.
MIB System
System Name
This is to give NetProbe Lite a name.
System Contact
This is to give the administrator a name.
System Location
This is to set NetProbe Lite location.
ii.
Access Control
Manager IP Address
This set the IP address from where the administrator can manage NetProbe Lite.
It is valid for up to 8 IP addresses. Use *.*.*.* to manage NetProbe Lite from any
IP addresses.
Community
-19-
This is to set a Community name for NMS. The community name has to be the
same as that set in NMS.
Permission
This is to set the administrator’s authority. Options are Read, Read/Write, and No
Access.
Description
This is for an administrator to make notes
iii.
Trap Notification
The user can set up to eight (8) Trap recipient’s address.
Receiver IP Address
Enter the email address of the person to receive Trap Notification.
Community
This is to set a Community name for NMS. The community name has to be the
same as that set in NMS.
Severity
This determines the severity of the Trap. It is divided into three main types:
Type
Information
Warning
Severe
Description
To receive all traps
To receive only “warning” and “Severe” traps
To receive only severe trap
Please refer to your NMS for Trap levels and settings.
Accept
Use this section to set weather the recipient should receive a TRAP or not.
Useful for temporarily disable Trap reception for the user.
Description
This is for the administrator to make short notes (Max of 47 characters).
-20-
Events
This section allows you to select events you will be notified of from a drop-down
list. Click the “select” button, a menu will open. Click either “Yes” or “No”.
Note: The Trap notification for the “Input Events” will depend on the Signal
Detection Type selected under NetProbe Properties.
Fig.24 Trap Selection in a 4-Contact Closure Signal Detection setting.
Click “Apply” to confirm otherwise the changes will not be saved. NetProbe Lite
will confirm changes with a “Write Complete” message. Click “OK” to return to
the menu.
2.2.4
Email
This option sets the Email details for NetProbe Lite.
i.
E-mail Settings
Fig.25 NetProbe Lite E-mail Setting
E-mail Server
Enter the email server.
-21-
Sender’s Email Address
This item determines NetProbe Lite’s Email address.
Email Server Requires Authentication
If set to “YES”, the user will have to provide the account/password for accessing
the Email server. Otherwise, enter “NO”.
Account Name
Enter the account (login) name for the email server (Maximum 32 characters).
Password
Enter the password for the above account name.
Send Email When Event Occurs
If set to “YES”, NetProbe Lite will send an email to the Recipient’s Email Address
when an event occurs. Enter up to 8 recipient’s email address in the next
section.
ii.
Recipient’s Email Address (for Event Log)
The user can determine which eight (8) email addresses will receive email
notification when an event occurs.
Fig.26 NetProbe Lite Event Log recipient’s email address
Events
This section determines the type of event an email is sent by NetProbe Lite.
lists of available events are similar to the Trap Notification event selection.
The
-22-
Fig.27 NetProbe Lite Event Selection List
NetProbe Lite will send the following email notification depending on which event
has been selected.
Fig.28 NetProbe Lite A Trap Event Notification
iii.
Recipient’s Email Address (for Daily Report)
The user can determine which four (4) email addresses will receive a Daily Report
from NetProbe Lite.
-23-
Fig.29 NetProbe Lite Daily Report recipient’s email address
Account
Enter the email address of the daily report recipient.
Send Email for Daily Report (hh:mm:ss)
To enable sending of a daily report, click “Yes” and enter the report time in 24hr
format. The Daily report will include information from Event Log and Data Log.
Fig.30 NetProbe Lite Daily Report email
Send Email When Data Log overflow (500 records)
This will send an email to the recipient notify that the recorded data has exceeded
500 items.
2.2.5
WEB
This section allows you to set up to eight (8) User account for NetProbe Lite. Once set,
a valid username and password must be entered in order to access NetProbe Lite.
i.
User Account
User Name
Enter a user name here (maximum length is 32 characters).
-24-
Password
Set a password for the account (maximum length is 16 characters, case
sensitive).
Permission
Determine the permission to Read/Write (Administrator) or Read only.
WARNING: You MUST set at least one User Account permission to
Read/Write (Administrator) BEFORE setting a Read Only. Failure to do so will
result in you being locked out of NetProbe Lite Web Manager!
IP Filter
To increase security, the Administrator can specify the IP address of the user
logging in. Leave “*.*.*.*” to allow the user to login from any place.
Click “Apply” to accept changes. NetProbe Lite will confirm with a “Write
Complete” message. Click “Reset” to undo current changes.
2.2.6
System Time
This section is to set and synchronize NetProbe Lite System Time with the chosen
Time Server.
i.
System Time
Time Between Automatic Updates
This item sets the interval between each time synchronization. Select either; 1, 3,
12 hours or 1, 10 & 30 days. For manual and instant update, click “Adjust Now”
Time Server
Click the down arrow and choose the nearest Time Server to your NetProbe Lite
location. Click “Edit” to bring up a list of 30 of the most common Time Servers.
-25-
Note: NetProbe Lite can list a maximum of 30 Time Servers. In order to “Add”
a new time server location, you must first delete an existing time server from
the list.
To add a new time server location;
1. Click “Delete” to remove unwanted Time Server.
2. Click “OK” when it prompt “Are you sure that you want to delete the data?”
3. Enter the new time server URL in the space below and click “Add”.
Click “Back” to go back to the System Time menu.
Time Zone (Relative to GMT)
Select the appropriate time zone for your area relative to GMT.
Time will change automatically when the Time Zone is set.
The System
System Time (mm/dd/yyyy hh:mm:ss)
This section is to set NetProbe Lite System Time manually. The format is
pre-determined to: mm/dd/yyyy hh:mm:ss
ii.
Auto Restart
Auto Restart System for Every (0: Disable)
Use this setting to auto restart the system at a predetermined interval. The
default value is set to “0” (disabled). Enter between, 1 to 9999 Minute (i.e.,
between 1 minute or 166.65 hour) or 1 to 9999 Hour (1 hour to 416.6 days).
Warning: If the system resets, all the data recorded in the Event Log or Data
Log will be erased!
Manual Restart System
Use this feature to manually restart the system.
1. Click “Apply”,
2. A “Restart System Now” message will appear to confirm that the system is
being restarted.
-26-
3. Click IE or your browser Refresh button to return to the webpage.
2.3 Log Information
NetProbe Lite will create log information for any variations detected and record it.
Two types of logs are available,
2.3.1 Event Log
2.3.2 Data Log
2.3.1 Event Log
An event log will be created for each of the device connected to NetProbe Lite. A
total of 500 records can be logged. Click “Clear” at the bottom right of the log to
delete all log files. The Event Log will record;
Date/Time
This is a record of the Date (mm/dd/yyyy) and Time (hh:mm:ss) when the data
was recorded. The interval between every log can be set in Configuration.
Type
This shows the current Signal Detection Type.
Refer to the icons below;
:
8-Analog Input
:
4-Differential Signal Input (Bipolar)
:
4-Differential Signal Input (Unipolar)
:
4-Contact Closure Input
Event
This displays the event corresponding to the Date/Time.
recorded for the detection:
Signal Detection Type
a. 8-Analog Input
b. 4-Differential Signal Input
(Bipolar)
c. 4-Differential Signal input
(unipolar)
The events that will be
Event Recorded
Group #; Overrun, Normal and Underrun
-27-
d. 4-ContactClosure Input
Group #; Close or Open state
2.3.2 Data Log
This is a data log page. It record changes in temperature, humidity and data from
each connected device. It can log up to 500 events.
When this limit is reached NetProbe Lite will delete the earliest event record and
continue logging new events. Logs can be saved in CSV format by clicking on “Save
Data Log”.
Note: To change the record interval between each data log go to “NetProbe
Properties” Æ “Data Log”
2.3.3 Save Data Log
Use this function to save a record of the Data Log.
in the event of a system reboot.
Any record not saved will be lost
1. Click on “Save Data Log” to download the CSV file.
location. The default file name is netprobe.csv
Choose a file name and
2. Click “Save” to start downloading the file.
-28-
3. Use Microsoft Excel to open the file.
2.4 Help
2.4.1 About NetProbe
Fig.31 Event Log
NetProbe Lite Firmware Version
Display NetProbe Lite firmware version details.
NetProbe Lite Hardware Version
Show the hardware version.
NetProbe Lite Serial Number
Shows the serial number
Reset to Factory Default
Resets all settings to default settings.
-29-
Manufacturers Details
Display the manufacture’s contact details. Click on the email address to send an
email to Mega System Technologies, Inc. Alternatively, click on the url to visit the
website.
-30-
Appendix A: Methods to Update NetProbe Lite Firmware
Appendix A: Methods to Update NetProbe Lite
Firmware
You can update NetProbe Lite’s firmware using any of the following methods.
Method 1: Using Netility
(1) Use “Download Firmware” function under Netility to update it.
Method 2: Using FTP
Windows FTP is another way to upload the latest firmware into NetProbe Lite.
You can also use other FTP client software to do this.
In the following example, NetProbe Lite IP address is 192.168.50.179
(1) Click “Start” on Windows taskbar, then “Run..”, type in “ftp 192.168.50.179”
(2) Click “OK”
(3) The systems will requests for your User Name and Password. Enter “admin”
for User Name and press “Enter”. The default password is left blank.
Once the User Name and Password is verified, the server will response with
“230 OK” to indicate that Login is successful.
If you enter the wrong Username or Password, the server will response with
“530 Not Logged in”.
(4) FTP commands:
-31-
ls : This command request the server to list all files and sub-file in the current
menu. User may finds out the firmware version of the NetProbe Lite of its IP.
put <client’s file route> : This command ask the client to copy its specific file
route to the Server point. Use this to upload the latest firmware to your
NetProbe Lite
quit : This command allow the user to logout and close the FTP connection.
Illustration: The picture shows, that the latest NetProbe Lite firmware file
uploaded from the local computer located in
(c:\work\netagent\prjs\nag\2.32.DK520.bin) to the NetProbe Lite with an IP
address 192.168.50.179
Method 4: Using IE Browser
This method uses IE to update the latest firmware. Open IE, then type in the
account, password and NetProbe Lite IP address to be updated in the following
format, ftp://<username>:<password>@<NetProbe Lite IP address>.
Once logged in, the current firmware and version will be displayed. Copy the
latest firmware to here to complete the updating process.
There are two method to log in:
(a) ftp://admin:password@192.168.50.179
Enter the password that was set earlier using Netility. Otherwise, enter
NetProbe Lite’s default value:
Username: admin
Password: <blank>
(example: ftp://admin:@192.168.50.179)
(b) ftp://192.168.50.179/
The follow error message will show, when the above is entered. Ignore it and
select “Enter Identity” at the top left corner of file menu. Then enter “admin”
as the User Name and <blank> Password to re-enter.
-32-
Once the connection has been established, the following window will be display.
The user may then transfer the latest firmware here in order to complete the
updating steps.
-33-

NetProbe Lite

Transcription

Similar documents

LITE HARNESS

Submittal Sheets - Westpac Materials

Aladdin Eye Lite - Video Cine Import

ELITE Lite - Institute for Creative Technologies

TM - Bradley`s Auction Service

TankNET Lite.Wine-Beer.NoBleed.Front(rfs)

PDF - Wild Blueberry Pancake Breakfast

What is good mood food?

french - Doorsmith

Stayflats™ Lite Mailer