Verve Worktops

Cleaning Instructions
Your Verve Worktops
are easy to maintain
and clean.
Arnold Laver
Depots
There’s nothing easier than cleaning and caring for your
Verve Worktops.
A major advantage of our worktops is that the HPL surface makes cleaning so
simple. Usually a moist cloth is sufficient, but use washing-up liquid to get rid
of any grease. Stubborn dirt can be removed with an organic solvent such as
methylated spirits or alcohol. A brush with hard bristles (but not wire brushes)
may also be used, but not on glossy worktops.
Cleaning Recommendations
Light Stains/Dirt
Normal Stains/Dirt
3
4
1
2
3
F.I.R.A. Gold Award*
1
Resin Impregnated Paper
I.S.O. 9001 Registered
Company
2
Drip Seal
3
*3mm Radius (*Gloss Decors 6mm)
4
4mm Sealed
Face high pressure laminate
guaranteed to BS EN 438
Core CIA Chipboard
Backing Resin Impregnated
Paper
Water resistant seal under
side joint and back edge
Supplied with matching
edging strip
All Glossy Laminate
Worktops come with
a protective film to be
removed after fitting
Always avoid placing hot saucepans/kitchen utensils
directly onto the worktop, always use a protective pad/mat
(worktop saver).
Always avoid cutting or chopping directly on the
Worktop. Always use a protective mat (worktop saver).
Always avoid excess water around areas where there are
cut joints and cut outs as these are potential weak areas.
Wipe away excess water immediately.
Canal Road, Bradford, BD2 1AR
T 01274 732861 F 01274 737060
E bradford@laver.co.uk
Crowle Street, Hull, HU9 1RH
T 01482 324525 F 01482 216478
E hull@laver.co.uk
Dry or damp paper towels, a cloth or sponge.
Verve
Range
Profile
Dudley Road, Oldbury, West Midlands, B69 3DA
T 0121 552 7788 F 0121 544 7186
E birmingham@laver.co.uk
Fat, oil and dirt particles, fingermarks, lime deposits, rust, juice, coffee, tea,
wax, blood, universal marker etc - With a cloth or soft nylon brush and washing
powder, soft soap, toilet soap or washing-up liquid. If necessary, leave for a
while and then rinse thoroughly with clean water.
Firs Trading Estate, Oldington Lane,
Kidderminster, DY11 7QN
T 01562 66557 F 01562 864557
E kidderminster@laver.co.uk
Heavy Stains/Dirt
Pontefract Road, Stourton, Leeds, LS10 1SW
T 0113 270 4086 F 0113 272 3833
E leeds@laver.co.uk
Discolouration through long exposure to tea, coffee, fruit juice etc - With
washing powder and household bleach (but do not repeat too often).
Lead pencil, felt-tip pens, marker and ball-point pens, lipstick, crayons, wax,
shoe polish, nicotine, nail varnish - With an organic solvent such as acetone
(nail varnish remover), methylated spirits, petroleum spirit, percholroethene.
Read the manufacturer’s instructions carefully!
Paint (water or solvent based paints, two-component paints, spray paints),
varnish stains, printing ink - With water or organic solvent. Remove
two-component paints immediately.
Adhesives (water-based, dispersion) - With water or an organic solvent.
Two-component adhesives, urea resin, melamine, phenolic resin - Remove
immediately. Do not allow to harden!
Cleaning and Caring for your Gloss Worktop
General cleaning of the surface requires only a damp cloth and a mild detergent
or non-abrasive cleaner diluted in warm water.
Abrasive scouring powders, creams and even polishes should all be avoided.
Potentialy persistent stains should be removed immediately. Buff the surface
after cleaning with a soft cloth.
Always use a chopping board/worktop saver. Gloss worktops will
show scratching, cuts, heat damage, more easily than a standard
finish worktop.
Any granulated sugar spills should be lightly brushed away.
Do not apply pressure whilst wiping to avoid scratching.
* F.I.R.A. do not issue the gold
award to glossy worktops
124 New Road, Rainham, Essex, RM13 8RS
T 01708 529 500 F 01708 529 501
E london@laver.co.uk
Liverpool Road, Cadishead, Manchester,
M44 5BZ
T 0161 777 9000 F 0161 777 9007
E manchester@laver.co.uk
Wagonway Road, Hebburn Tyne & Wear,
NE31 1SP
T 0191 428 6666 F 0191 428 6622
E newcastle@laver.co.uk
Basingstoke Road, Reading, RG2 0QN
T 0118 975 1100 F 0118 975 1900
E reading@laver.co.uk
Sheffield Mosborough, Olympic Sawmills
Oxclose Park Road North, Sheffield, S20 8GN
T 0114 276 4700 F 0114 276 4701
E sheffield@laver.co.uk
Sheffield Central, Little London Road, Heeley
Sheffield, S8 0UH
T 0114 255 7341 F 0114 292 3660
E sheffield@laver.co.uk
verve
WORKTOPS
YEAR
TE
E
• 5 YEAR G
E
TEE • 5 Y
G UAR
AN
Dark Coimbra Ash
Black Andromeda Gloss
Natural Concrete
Oxyde Rust
Walnut Butcher Block
Kamala Dark Grey
•
EAR
AR
A R A NT E E
Solino
AN
5
GU
Oxyde
5Y
The Verve
Worktop
Range
AR
Quarry Pearl White
U
Worktops
The Verve Worktops Range
carries a 5-year guarantee
against all manufacturing
defects subject to normal
usage and correct installation.
Rovere Casa Dark
Marmor Marquina Brown
Vesuz Grey Medium
Walnut Lyon
3050mm x 600mm x 38mm
4100mm x 600mm x 38mm
3050mm x 665mm x 38mm
4100mm x 900mm x 38mm
Gloss worktops
are not guaranteed
against surface
scratching.
Loft
Granito Veneziano
Lost World Dark Brown
Masari Antique
Upstands
3050mm x 100mm x 18mm
Soft Cocktail
Porphyr Beige
Quarry Black
White Andromeda Gloss
Splashbacks
Available to order
Arnold Laver
The Verve Worktop Range
Your Verve Worktops
are easy to maintain
and clean.
YEAR
TE
E
• 5 YEAR G
E
TEE • 5 Y
G UAR
AN
•
EAR
AR
A R A NT E E
AN
5
GU
5Y
The Verve
Worktop
Range
AR
U
Verve
Range
Profile
The Verve Worktops Range
carries a 5-year guarantee
against all manufacturing
defects subject to normal
usage and correct installation.
Gloss worktops
are not guaranteed
against surface
scratching.
3
4
1
2
3
F.I.R.A. Gold Award*
1
Resin Impregnated Paper
I.S.O. 9001 Registered
Company
2
Drip Seal
3
*3mm Radius (*Gloss Decors 6mm)
4
4mm Sealed
Face high pressure laminate
guaranteed to BS EN 438
Core CIA Chipboard
Backing Resin Impregnated
Paper
Water resistant seal under
side joint and back edge
Supplied with matching
edging strip
All Glossy Laminate
Worktops come with
a protective film to be
removed after fitting
Arnold Laver
The Verve Worktop Range
Always avoid placing hot saucepans/kitchen utensils
directly onto the worktop, always use a protective pad/mat
(worktop saver).
Always avoid cutting or chopping directly on the
Worktop. Always use a protective mat (worktop saver).
Always avoid excess water around areas where there are
cut joints and cut outs as these are potential weak areas.
Wipe away excess water immediately.