July 2013 - Belconnen Model Aero Club

Wingtips
July 2013
Editor: Brian Oakes
Above: Featured Model of the Month takes off.
See page 3.
On other pages
From the Editor in Queensland
Featured model of the Month
July Crossword
Seen at the Field
Solution to June Crossword
Committee Contact Details
page
page
page
page
page
page
2
3
4
5
5
5
Your editor came across the above photo in the
museum in Croydon, Qld, where planes were known
to land in the main street. Note the folding wings.
4. What model is the plane? (4 points). Solution on Questions: 1. Who manufactured the plane?
page 2. (If you’re not certain, guess — you’ll
(1 point). 2. Who owned the plane? (2 points). probably be right)
3. What was the plane used for? (3 points). Above and left, Graham Coronel's glider
seen last month at the field having a
narrow scrape with a crow.
Page 2
Editor in the
Outback
As you'll have
gathered, I'm on
holidays in north
Queensland. On
this page are
images I've
gathered along the
way.
While in Longreach, a visit to the
Qantas Founders' Museum is a must.
The photos show the main hall of the
museum and a replica of one of the
company's first aircraft, an Avro
504K, and the original Qantas
hangar.
Yes, I'm still flying model aircraft, namely the
Nadar, which carries a camera to 500 feet or
more. Here's one photo, a dry creek bed south
of Mt Isa, complete with nervous pilot and his
car (inset). For those not familiar with the
Nadar and its abilities, see Wingtips, September
2011.
Brian Oakes
Answers to the page 1 questions. 1. De Havilland.
2. Qantas, who leased it to the Royal Flying Doctor
Service. 3. An air ambulance, used from 1934 to
1943. 4. A DH-83 Fox Moth. It looks a lot like a Tiger
Moth because they had many parts in common.
Page 3
el
d
o
M th
ed on
r
tu e M
a
Fe f th
o
The Flair Puppeteer, a 1/6 sport scale Sopwith Pup built and flown by Bob Raadts
Although this looks exactly like a
WWI Sopwith Pup, it's not quite to
scale, having been tweaked to
improve the flying characteristics.
(For instance the cowl has been
extended so the engine is further
forward, solving the problem of the
centre of gravity being too far back
for stable flight.) Hence the
manufacturers of the kit call it the
Puppeteer.
Bob built it from the Flair kit and
covered it in Solartex. For the decking forward of
the cockpit Bob used thin aluminium sheet that was
formerly litho printing plates. It's tricky to apply as
it's easily dented. To minimise weight aft, and for
scale appearance, there are pull-pull cables from
the servos to the rudder and elevator.
The model is powered by an ASP .61 four-stroke.
Ensuring that you have the correct incidence on
both top and bottom wings is difficult, Bob says.
Members who were on hand to see the Puppeteer's
maiden flight could see that it's a 'floater',
preferring not to land, but to glide a few metres
above the length of the runway. Consequently Bob
had several attempts at landing until he managed
to reduce the engine revs to idle.
Page 4
Wingtips Winter
Crossword for
July 2013.
The solution will
be in August
Wingtips and on
the clubhouse
notice board.
Across
1.
4.
6.
7.
8.
9.
13.
14.
16.
17.
18.
20.
21.
26.
28.
31.
33.
34.
36.
38.
41.
44.
45.
46.
47.
48.
49.
set aircraft down on the ground
WW2 fighter aircraft (7)
control surface that increases drag, lift or both
full-size aerobatic plane made by Zivko, often seen as
scale model
air traffic control (abbr.)
aircraft covering material
full-size aerobatic plane, also seen as scale model
Class of old-timer competition (6)
kind of model aircraft engine
WW2 United States air force (abbr) (5)
decibel (abbr)
rod used to strengthen an airframe
substance burnt to produce thrust
descent of an aircraft towards a landing area
visible line of vapour left by high-flying aeroplane
telescopic strut, often oil-filled
The aircraft in the photo (9,3,6)
Aircraft controls for 2 pilots
r/c transmitter control allowing minor adjustments in
flight
liquid often applied to tissue-covered models
engine covering
person controlling the flight of an r/c model
in the same direction as the wind
construction material
German manufacturer of r/c equipment
engine design, usually seen in full-size aeroplanes
Plane used for aerotow (3)
Down
2.
3.
5.
10.
11.
12.
15.
19.
22.
23.
24.
25.
27.
29.
30.
32.
35.
37.
39.
40.
42.
streamlined engine housing
aeroplane that has its wing behind the horizontal
stabiliser
a wing planform
Turn and ____ indicator (4)
well-known US aircraft manufacturer
Medal for valour
full-size aerobatic plane, also seen as scale model
aeroplane with two pairs of wings
the lightest metal
procedure in which aeroplane leaves the ground
trade name for a composite material
electrical cells connected in series
distance from leading edge to trailing edge of a wing
smaller replica
our club
manufacturer of r/c equipment
upward force
metal joining material
revolutions per minute (abbr)
part of a seaplane
mainplane
Page 5
Left: the
solution to
the June 2013
Wingtips
Winter
Crossword
Reminder
Even if you’re using 2.4GHz
equipment, it’s a good practice
to put your key in the frequency
board when flying.
Seen at the Field
Above: Ken Griffiths’ flying wing.
Above right: Andy Brough's Hi Climber, seen in last
month’s Wingtips, is now repaired, and is flying
particularly well. A worthwhile electric conversion
from rubber power!
BMAC committee
Safety Officer: Roger Pinder 6242 9699
rpinder@homemail.com.au
Chief Flying Instructor: Steve Mercer 6254 8737
steve.mercer@environment.gov.au
Wingtips Editor: Brian Oakes 6248 8885
elle.bee@apex.net.au
Committee Members:
Henk Jansen 6262 2120
lhjansen@bigpond.com
Peter Hamilton 6287 4464
peterrose@westnet.com.au
Gavin Voigt 6254 7821
President: Chris Elliott 0402 273 363
Christopher.Elliott@booz.com
Vice-President: Wayne Harris 6254 8792
wayneharris@grapevine.com.au
Treasurer: Darryl Barbour 0421 037 392
dbarbour@internode.on.net
Secretary: Jim Henderson 6255 1545
jchende@bigpond.com
Field Officer: Rob Clayton 6258 1218
robclayton@grapevine.com.au
”Wingtips” the Belconnen Model Aero Club
Newsletter published
15 July 2013