asahi keiki co.,ltd.

Transcription

DIGITAL PANEL METER
A1000
■ Features
!
· Low cost
W
NE
· Bright LED 14.2mm (red)
· AC power and DC power available
Input Specifications
■ DC Voltage, current
• DC voltage measurement (Range 12 to 14)
Range
12
13
14
Measurement
Range
±1.999V
±19.99V
±199.9V
Input
Input
Impedance Protection
±100V
±250V
1MΩ
±500V
Range
± 0.3% of F.S
PA
PJ
23
24
25
Measurement
Range
±19.99mA
±199.9mA
±1.999A
Input
Input
Resistance Protection
10Ω
±150mA
1Ω
±500mA
0.1Ω
±3A
Sensor
Type
Pt100Ω
Pt100Ω
Measurement
Max
Range
Resolution
-100.0 to +199.9°C 0.1°C
-200 to +600°C
1°C
Accuracy
(23°C±5°C, 35 to 85%)
± 0.2% of F.S
± 0.4% of F.S
Current for resistance: 1mA (TYP)
External lead resistance: less than 1 ohm per lead
• DC current measurement (Range 23 to 25)
Range
■ RTD (Pt100Ω) (Range PA, PJ)
Accuracy
(23°C±5°C, 35 to 85%)
Accuracy
(23°C±5°C, 35 to 85%)
± 0.5% of F.S
■ Process (Range 1V, 2A)
Accuracy
Input
Input
Range Measurement
Display
Impedance Protection (23°C±5°C, 35 to 85%)
Range
offset ±1000
1 to 5V
1MΩ
±100V
± 0.3% of F.S
1V
4 to 20mA fullscale ±100 to 1999 51Ω
50mA
± 0.4% of F.S
2A
■ AC Voltage, current
• AC voltage measurement (Range 12 to 14 Average)
Range
12
13
14
Measurement
Range
1.999V
19.99V
199.9V
Input
Input
Impedance Protection
50V
50V
1MΩ
500V
Accuracy
(23°C±5°C, 35 to 85%)
± 0.5% of F.S
Input Frequency: 40 Hz to 100Hz
Rectifier Circuit: Reprsents effective value of sine wave by
demodulation of mean value
Response time: approx 1 sec (10 to 90%)
• AC current measurement (Range 23 to 26 Average)
Range
23
24
25
26
Measurement
Range
19.999mA
199.9mA
1.999A
5A
Input
Input
Resistance Protection
10Ω
150mA
1Ω
500mA
0.1Ω
3A
1Ω
8A
Accuracy
(23°C±5°C, 35 to 85%)
± 1.0% of F.S
Input Frequency: 40 Hz to 100Hz
Rectifier Circuit: Reprsents effective value of sine wave by
demodulation of mean value
Response time: approx 1 sec (10 to 90%)
■ Common Specification
Input bias current:
50 pA (TYP)
Sampling speed:
2.5/sec
Over range indication: When input exceeds the maximum display
flash 1999
Max. display:
1999
Display:
Red LED 14.2mm height
Dimensions:
96mm (H) X 48mm (W) X 75mm (D) DIN size
Power supply:
90 to 132 VAC
180 to 264 VAC
5 to 24 VDC
Power Consumption: 1.5 VA at AC power
100mA at DC power
Operating Temp.:
0 to 50°C, 35 to 85%RH
Storage Temp.:
-10 to 70°C less than 60% RH
Dielectric Strength:
Power supply and input, 1500 VAC/1min at
AC power
Power supply and input, 500 VDC/1min at DC
power
Insulattion Resistance : 500 VDC 100MΩ at above terminals
■ Thermocouple (Range KC, JC)
Range
KC
JC
Sensor
Type
K
J
Measurement
Range
0 to +1000°C
0 to +400°C
Max
Resolution
1°C
1°C
Accuracy
(23°C±5°C, 35 to 85%)
± 0.8% of F.S
Sensor lead Resistance: less than 50Ω
Burn out: Flash -1999
Over input voltage: ±5VDC
Cold Junction Compensator Accuracy:±2°C
ASAHI KEIKI CO.,LTD.
DIGITAL PANEL METER
A1000
■ Model Code
A1씲1씲 -씲씲
Range
Input: 1. DC voltage
2. DC current
4. AC voltage
5. AC current
6. AC current 5A
B. Process
C. Thermocouple
D. RTD
Power Supply 1. 90 to 132 VAC
2. 180 to 264 VAC
3. 5 to 24 VDC ±10%
48
■ Dimensions
96
Front View
8.9
7.8
53
Side View
8.7
POW (-)
POW (-)
POW (+)
COM
LO
HOLD
25 range HI
POW (-)
POW (+)
COM
C
HOLD
B
RTD (PA, PJ)
POW (+)
COM
HOLD
LO
NC
1V range HI
2A range HI
Thermocouple (KC, JC)
A
NC
POW (-)
DC current (23 to 25 range)
AC current (23 to 25 range)
POW (+)
S
COM
-
HOLD
+
NC
DC voltage (12 to 14 range)
AC voltage (12 to 14 range)
24 range HI
23 range HI
POW (-)
POW (+)
COM
LO
HOLD
NC
12 range HI
13-14 range HI
■ Connection Diagram
Process
DIGITAL PANEL METER
A2100
■ Features
!
· LED hight 10mm
W
NE
· Power supply 5VDC or 5 to 24VDC
· 3 1/2 digit
■ DC Voltage Measurement
Range
11
12
13
14
Measurement
Range
±199.9mV
±1.999V
±19.99V
±199.9V
■ Ordering Code
Input Impedance
Input Protection
100MΩ
±50V
1MΩ
±250V
Accuracy
A21 0 -
± (0.1% of F.S)
Range
■ DC Current Measurement
Range
22
23
24
25
Measurement
Range
±1.999mA
±19.99mA
±199.9mA
±1.999A
Input Impedance
Input Protection
Accuracy
100Ω
10Ω
1Ω
0.1Ω
±50mA
±150mA
±500mA
±3A
± (0.2% of F.S)
Power Supply 1. non-isolation type (5VDC)
2. isolation type (5 to 24VDC)
■ Dimensions
■ Power supply
5VDC±5%
60mA
● Isolation type
Voltage:
Consumption:
5 to 24VDC
100mA
4.5
24
● Non-isolation type
Voltage:
Consumption:
48
■ Specification
Insulation resistance :
■ Panel Cutout
45
* Replacement for AP-200, AP-201A, AP-202A(no option)
Min35
Display :
Polarity :
Decimal point :
External control :
Operating Temp. :
Dimensions :
Weight :
Dielectric strength :
Single Ended
2.5/sec
1999
When input exceeds the maximum display,
0000 or -0000 flashes
Red LED, 10mm
A "-" is displayed automatically
Settable to any digit position by front SW
Hold
0 to 50˚C 35 to 85% RH
48mm(W)⫻24mm(H)⫻39.7mm(D) DIN size
40g
Power supply and input terminal at 500VDC/
1min
Case and each terminals at 1500VAC/1min
500VDC 100M⍀ at the above terminals
40
22.2
Input configuration:
Conversion rate:
Max display:
Overrange indication :
11. ±199.9mV
12. ±1.999V
13. ±19.99V
14. ±199.9V
22. ±1.999mA
23. ±19.99mA
24. ±199.9mA
25. ±1.999A
Min65
DIGITAL PANEL METER
A2200
■ Features
!
· LED hight 10mm
W
NE
· Power supply 5 to 24VDC (Isolation)
· 4 1/2 digit
Range
12
13
14
Measurement
Range
±1.999V
±19.99V
±199.9V
■ Ordering Code
Input Impedance
Input Protection
100MΩ
±50V
1MΩ
±250V
Accuracy
± (0.1% of F.S)
A2220 -
Range
■ Power supply
5 to 24VDC
100mA
■ Dimensions
■ Specification
Input configuration:
Conversion rate:
Max display:
Display :
Polarity :
Decimal point :
External control :
Operating Temp. :
Dimensions :
Weight :
Single Ended
2.5/sec
19999
0000 or -0000 flashes
Red LED, 10mm
Settable to any digit position by front SW
Hold
0 to 50˚C 35 to 85% RH
48mm(W)⫻24mm(H)⫻39.7mm(D) DIN size
40g
Power supply and input terminal at 500VDC/
1min
Case and each terminals at 1500VAC/1min
500VDC 100M⍀ at the above terminals
4.5
24
● Isolation type
Voltage:
Consumption:
12. ±1.9999V
13. ±19.999V
14. ±199.99V
48
40
■ Panel Cutout
22.2
* Replacement for AP-241A, AP-242A, AP-244A(no option)
Min35
45
Min65
Input Specification (A5XXX-첸첸)
• DC voltage, current
Range
01
11
Measurement range
±99.99 mV
Display
offset ±9999
full scale 0 to ±9999
Maximum Resolution
Input Impedance
Input Protection
Accuracy
10 µV
100 MΩ
±100 V
±(0.1% of FS)
Maximum Resolution
10 µV
1 mV
10 mV
100 mV
Input Impedance
100 MΩ
1 MΩ
10 MΩ
10 MΩ
Input Protection
±100 V
±250 V
±250 V
±600 V
Accuracy
±(0.1% of FS)
±(0.1% of FS)
±(0.1% of FS)
±(0.15% of FS)
Maximum Resolution
1 µA
10 µA
100 µA
Input Impedance
10 Ω
1Ω
0.1 Ω
Input Protection
±100 mA
±500 mA
±3 A
Accuracy
±(0.2% of FS)
±(0.2% of FS)
±(0.3% of FS)
Measurement range
±999.9 mV
±9.999 V
±99.99 V
±600 V
Display
02
Range
12
13
14
15
Range
23
24
25
Measurement range
±9.999 mA
±99.99 mA
±999.9 mA
Display
03
offset ±9999
offset ±9999
Input configuration
: Single ended
Measuring method
: ∆∑type
Normal mode rejection : More than NMR 50dB (50/60 Hz)
• AC voltage, current (Average)
Range
04
11
12
13
Range
05
14
15
Range
08
23
24
25
Range
09
26
Maximum
Resolution
10 µV
100 µV
1 mV
Input
Impedance
Maximum
Resolution
10 mV
100 mV
Input
Impedance
Maximum
Resolution
1 µA
10 µA
100 µA
Input
Impedance
10 Ω
1Ω
0.1 Ω
Input
Protection
100 mA
500 mA
3A
Display
Maximum
Resolution
Input
Impedance
Input
Protection
Accuracy
offset ±9999
1 mA
CT
8A
±(0.5% of rdg + 10 digit)
Maximum
Resolution
10 µV
100 µV
1 mV
Input
Impedance
Input
Protection
100 V
100 V
250 V
Maximum
Resolution
10 mV
100 mV
Input
Impedance
more than 1 MΩ
Input
Protection
250 V
600 V
Maximum
Resolution
1 µA
10 µA
100 µA
Input
Impedance
10 Ω
1Ω
0.1 Ω
Input
Protection
100 mA
500 mA
3A
Measurement
range
99.99 mV
999.9 mV
9.999 V
Input Frequency
Display
40 Hz to 1 kHz
offset ±9999
Measurement
range
99.99 V
600 V
Input Frequency
Display
40 Hz to 1 kHz
offset ±9999
Measurement
range
9.999 mA
99.99 mA
999.9 mA
Input Frequency
Display
40 Hz to 1 kHz
offset ±9999
Measurement
range
Input Frequency
50 Hz or 60 Hz
5A
more than 1 MΩ
more than 1 MΩ
Input
Protection
100 V
100 V
250 V
Accuracy
Input
Protection
250 V
600 V
Accuracy
Accuracy
• AC voltage, current (TRUE-RMS)
Range
06
11
12
13
Range
07
14
15
Range
10
23
24
25
Range
11
26
Measurement
range
99.99 mV
999.9 mV
9.999 V
Measurement
range
99.99 V
600 V
Measurement
range
9.999 mA
99.99 mA
999.9 mA
Measurement
range
5A
Input configuration
Response time
Crest factor
Dead zone
:
:
:
:
Input Frequency
Display
40 Hz to 1 kHz
offset ±9999
Input Frequency
Display
40 Hz to 1 kHz
offset ±9999
Input Frequency
Display
40 Hz to 1 kHz
offset ±9999
Input Frequency
Display
Maximum
Resolution
Input
Impedance
Input
Protection
Accuracy
50 Hz or 60 Hz
offset ±9999
1 mA
CT
8A
Single ended
Approx. 1 sec.
4:1 at fullscale (only for TRUE-RMS)
0 to 99 digit
• Resistance
Range
12
11
12
13
14
Measurement
Display
range
99.99 Ω
offset ±9999
999.9 Ω
9.999 kΩ
99.99 kΩ
Maximum Resolution Current
Accuracy
10 mΩ
100 mΩ
1Ω
10 Ω
±(0.2% of FS)
±(0.1% of FS)
±(0.1% of FS)
±(0.1% of FS)
5 mA
0.5 mA
50 µA
5 µA
• Thermocouple
Range
13
KA
KB
J
T
S
R
B
Sensor
type
K
K
J
T
S
R
B
Maximum
Resolution
0.1°C
1°C
1°C
1°C
1°C
1°C
1°C
Measurement
range
–50.0 to 199.9°C
–50 to 1200°C
–50 to 1000°C
–50 to 400°C
0 to 1700°C
–10 to 1700°C
100 to 1800°C
available Fahrenheit display
Cold junction compensator accuracy
Sensor lead resistance
Linearizing method
Burn out alarm
:
:
:
:
±1°C (10 to 40°C)
less than 50Ω
Digital linearizing
-----
Accuracy
±(0.5% of FS)
±(0.2% of FS)
±(0.2% of FS)
±(0.6% of FS)
±(0.4% of FS)
±(0.4% of FS)
±(0.4% of FS) over 500°C
more than 1 MΩ
Accuracy
Accuracy
Accuracy
• RTD
Range Sensor type
PA
PT100Ω
PB
PT100Ω
Current for resistance
External lead resistance
Linearizing method
Burn out alarm
Measurement range
–100.0 to 199.9°C
–100 to 600°C
14
:
:
:
:
Maximum Resolution
0.1°C
1°C
Accuracy
±(0.15% of FS)
±(0.3% of FS)
Approx. 1 mA
Less than 10 Ω/lead
Digital linearizing
-----
• Frequency
Range
11
12
13
14
Display
Measurement range
0.1 to 200 Hz
1 to 2000 Hz
0.01 to 20 kHz
0.1 to 200 kHz
Prescale
: 0.001 to 5
1 to 100
Maximum Resolution
0.1 Hz
1 Hz
10 Hz
100 Hz
Display Renewal time
1 to 10 s
1s
100 ms
100 ms
15
Input type
Open collector
Logic
Magnet
Input voltage level
L: less than 1 V (5 V, 2.2 kΩ) pullup
L: less than 1 V, HI: 2.5 to 15 V
0.3 to 30 V P-P
Input Protection
30 V
15 V
15 V
16
Input type
Voltage
Input voltage level
50 to 500 V rms
Input Protection
500 V
Accuracy
±(0.2% of FS)
±(0.2% of FS)
±(0.2% of FS)
±(0.2% of FS)
• Strain gauge
17
Power supply
for sensor
5V
10 V
Zero adjustment range
Span adjustment range
Maximum Resolution Accuracy
–0.3 to +2 mV/V
1 to 3 mV/V
0.5 µV/digit
1 µV/digit
Sensor
: 350 Ω
Power supply for sensor : 5 V±5% (less than 15 mA)
±(0.1% of FS) +2 digit
10 V±5% (less than 30 mA)
• Process
Range
18
1V
2A
Measurement range Display
offset ±9999
1 to 5 V
4 to 20 mA
Input Impedance
1 MΩ
10 Ω
Input protection
±100 V
±100 mA
Accuracy
±(0.2% of FS)
±(0.2% of FS)
Input Impedance
1 MΩ
10 Ω
Input protection
±100 V
±100 mA
Accuracy
±(0.2% of FS)
±(0.2% of FS)
• Process with sensor power supply
Range
19
1V
2A
Measurement range Display
offset ±9999
1 to 5 V
4 to 20 mA
Power supply for sensor : 12 V DC ±10% 50 mA
24 V DC ±10% 25 mA
Output Specification
• HI & LO setpoint output (A5XX1-XX)
Indication > High setpoint
High setpoint Indication
Indication < Lo setpoint
Lo setpoint
HI
GO
LO
Setting range
: –9999 to 9999
Hysteresis
: 1 to 999 digit for each setpoints
Relay contact capacity : AC240V 8A resistive load
DC30V 8A resistive load
• Analog output (A5XX2-XX)
Output
0 to 1 V
0 to 10 V
1 to 5 V
4 to 20 mA
Resistive load
more than 10 kΩ
more than 10 kΩ
more than 10 kΩ
less than 550 Ω
Output method : PWM method
Scaling
: Digital scaling
Accuracy
±(0.5% of FS)
• RS-232C (Conforming to EIA RS-232C) (A5XX3-XX)
Communication method
Transmission speed
Start bit
Data length
Parity
Stop bit
Character code
Transmission control process
:
:
:
:
:
:
:
:
Full duplex
2400/4800/9600/19200/38400 bps
1 bit
7 bit/8 bit
Even parity/odd parity
1 bit/2 bit
ASCII code
Ignored process
• RS-485 (Conforming to EIA RS-485) (A5XX4-XX)
Transmission speed
Start bit
Data length
Parity
Error detection
Stop bit
Character code
Signal name
:
:
:
:
:
:
:
:
:
:
Full duplex
2400/4800/9600/19200/38400 bps
1 bit
7 bit/8 bit
Even parity/odd parity
BCC
1 bit/2 bit
ASCII code
Ignored process
+ non reversal output
– reversal output
Maximum No. of meter connected : 31
Line length
: Up to 500 m in total
Common Specification
Display
: Main display Red LED 14.2 mm height
Sub display Green LED 8 mm height
Conversion rate
: 12.5 times/sec.
Maximum display
: 9999
Overrange indication : When input exceeds the maximum display,
display OL or –OL
Zero display
: Leading zero suppression
Decimal point
: Settable to any digit position
External control
: Start/Hold, Peak Hold, Digital Zero
Operating temp.
: 0 to 50°C 35 to 85% RH
Storage temp.
: –10 to 70°C less than 60% RH
Power supply
: AC 100 to 240V±10%(AC main unit)
DC 9 to 60 V
(DC main unit)
Power consumption
: approx 4 VA (at 100 V)
Dimensions
: 96 mm (W) X 48 mm (H) X 147.5 mm (D) DIN size
Weight
: approx. 450 g
Dielectric strength (AC) : Power supply/input terminal/output terminal
Input terminal/output terminal
Case/power supply/input terminal output terminal
Dielectric strength (DC) : Power supply/input terminal/output terminal
Input terminal/output terminal
Case/power supply/input terminal output terminal
Insulation resistance
: DC500 V more than 100 MΩ at the above terminals
Dimensions
AC2000 V/1 min.
DC500 V/1 min.
AC2000 V/1 min.
DC500 V/1 min.
DC500 V/1 min.
AC2000 V/1 min.
Ordering Code
A5
92
7
121
147.5
Input
45
96
MIN.70
45 +0.6
-0
48
92 +0.8
-0
MIN.120
Output
01.
02.
03.
04.
05.
06.
07.
08.
09.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
0.
1.
2.
3.
4.
5.
6.
7.
DC voltage (±99.99 mV)
DC voltage (±999.9 mV to ±600V)
DC current (±9.999 mA to ±999.9 mA)
AC voltage AVG (99.99 mV to 9.999 V)
AC voltage AVG (99.99 V to 600 V)
AC voltage RMS (99.99 mV to 9.999 V)
AC voltage RMS (99.99 V to 600 V)
AC current AVG (9.999 mA to 999.9 mA)
AC current AVG (5 A)
AC current RMS (9.999 mA to 999.9 mA)
AC current RMS (5 A)
Resistance (99.99 Ω to 99.99 kΩ)
Temperature (Thermocouple)
Temperature (RTD)
Frequency (Open collector, Logic, Magnet)
Frequency (50 to 500 Vrms)
Strain gauge
1 to 5 V, 4 to 20 mA
1 to 5 V, 4 to 20 mA with sensor power supply
∗ Impossible to use only No.19 input for DC power supply
None
HI & LO setpoint
Analog output
RS-232C
RS-485
HI & LO setpoint + analog output
HI & LO setpoint + analog output + RS-232C
HI & LO setpoint + analog output + RS-485
Display board 1. Single
2. Multiple
Main board
1. AC100 - 240 V (±10%)
2. DC9 - 60 V
We reserve the right to change specifications without notice.
33-6, YAGUCHI 2-CHOME, OHTA-KU,
TOKYO 146-8505, JAPAN
FAX
: (03)3757-2989
PHONE : (03)3579-3893
http:// www.asahikeiki.co.jp
E-mail: dpm-overseas@asahikeiki.co.jp
Printed in Japan, Aug. 2004 (KP)
Display multi type (A6X1X-XX)
Display single type (A6X2X-XX)
왎 DC voltage,current
• A6XX1-XX
Range
11
12
13
14
15
Measurement Range
±99.99 mV
±999.9 mV
±9.999 V
±99.99 V
±700 V
Display
offset ±9999
full scale ±9999
Input Protection
±50 V
±50 V
±250 V
±250 V
±700 V
Accuracy (23˚C ± 5˚C, 35 ~ 85% RH)
±(0.03% of rdg + 1digit)
• A6XX2-XX
Range
21
22
23
24
Measurement Range
±99.99 uA
±999.9 uA
±9.999 mA
±99.99 mA
Display
offset ±9999
full scale ±9999
Input Protection
±10 mA
±10 mA
±50 mA
±500 mA
Accuracy (23˚C ± 5˚C, 35 ~ 85% RH)
• A6XX3-XX
Range
25
26
Measurement Range
±999.9 mA
±2.000 A
Display
offset ± 9999
full scale ±9999
Input Protection
Accuracy (23˚C ± 5˚C, 35 ~ 85% RH)
±3 A
Input Protection
50 V
50 V
250 V
250 V
700 V
Accuracy (23˚C ± 5˚C, 35 ~ 85% RH)
왎 AC voltage, current (TRUE-RMS)
• A6XX4-XX
Range
11
12
13
14
15
Measurement Range
99.99 mV
999.9 mV
9.999 V
99.99 V
700.0 V
Display
offset ±9999
full scale ±9999
Minimum display 50 digits
• A6XX5-XX
Range
21
22
23
24
Measurement Range
99.99 uA
999.9 uA
9.999 mA
99.99 mA
Display
offset ±9999
full scale ±9999
Input Protection
10 mA
10 mA
50 mA
500 mA
Accuracy (23˚C ±5˚C, 35 ~ 85% RH)
• A6XX6-XX
Range
25
26
Measurement Range
999.9 mA
5A
Display
offset ±9999
full scale ±9999
Input Protection
3A
8A
Accuracy (23˚C ±5˚C, 35 ~ 85% RH)
Display
Current
5 mA
0.5 mA
50 uA
5 uA
Accuracy (23°C ±5˚C, 35 ~ 85% RH)
왎 Resistance
• A6XX7-XX
Range
11
12
13
14
Measurement Range
99.99 Ω
999.9 Ω
9.999 KΩ
99.99 kΩ
offset ±9999
full scale ±9999
Measurement method: Two or Four wire (internal socket changable)
왎 Thermocouple • RTD
• A6XX8-XX
Range
KA
KB
J
T
S
R
B
PA
PB
Sensor type
K
K
J
T
S
R
B
PT100 Ω
PT100 Ω
Linearzing method
Burn out alarm
Conversion time
Measurement Range
-50.0 to 199.9˚C
-50 to 1200˚C
-50 to 1000˚C
-50 to 400˚C
0 to 1700˚C
-10 to 1700˚C
100 to 1800˚C
-100.0 to 199.9˚C
-100 to 600˚C
Maximum Resolution
0.1˚C
1˚C
1˚C
1˚C
1˚C
1˚C
1˚C
0.1˚C
1˚C
: ±2˚C (10 to 40˚C)
: less than 50 Ω
: Digital linearizing
:----: 2.5/sec
왎 Frequency
• A6XX9-XX
Range
11
12
13
Measurement Range
0.1 to 999.9 Hz
1 to 9.999 kHz
10 to 99.99 kHz
Accuracy (23˚C ±5, 35 ~ 85% RH)
±(0.2% of FS)
• A6XX9-XX
Input type
Open collector
Logic
Magnet
Voltage
Input voltage level
L: less than 1.5 V (5V, pullup)
0.3 to 30 V P-P
30 V rms to 500 V rms
Prescale
: 0.01 ~ 10.00
PPR
: 1~100
Power supply for sensor : 12 VDC ±10%
Input Protection
30 V
15 V
30 V
500 V
Accuracy (23˚C ±5˚C, 35 ~ 85% RH)
±(0.5% of FS)
±(0.2% of FS)
±(0.2% of FS)
±(0.6% of FS)
±(0.4% of FS)
±(0.4% of FS)
±(0.4% of FS)
±(0.15% of FS)
±(0.3% of FS)
왎 Strain gauge
• A6XXA-XX
sensor
5V
10 V
Measurement range
Accuracy
-1 to + 1 mV/V
1 to 3mV/V
-4 ~ + 4 mV/V
±(0.1% of FS) + 2 digit
Sesnor
: 350 Ω
Power supply for sensor : 5 V ± 5% (less than 15 mA)
10 V ± 5% (less than 30 mA)
Conversion speed
: 1000/sec
왎 Process
• A6XXB-XX
sensor
1V
2V
2A
3A
Measurement Range
1 to 5 V
±5 V
4 to 20 mA
±20 mA
Display
Accuracy
offset: ±9999
Excitation power supply : 12 VDC ±5%
24 VDC ±5% 25 mA
• HI & LO setpoints output (A6XXX-1X Relay output)
(A6XXX-2X Photocoupler)
Comparative condition:
Indication > High setpoint
HIgh setpoint Indication
Indication < Lo setpoint
HI
GO
LO
Lo setpoint
Setting range
: -9999 to 9999
Hysteresis
Relay contact capacity : AC250 V 2 A resistive load
DC30 V 2 A resistive load
Photocoupler capacity : DC30 V 20 mA
Option
• External control (A6XXX-X1)
: Shorted between COM terminal and start/hold terminal or same level / hold
Open COM terminal and start/hold terminal or 5 V / start
D. ZERO
: Shorted between COM terminal and D.ZERO terminal / ON
P.HOLD
: Shorted between COM terminal and P. HOLD terminal / ON
R.RE (relay reset) : Shorted between COM terminal and R.RE terminal / ON
P.SEL1 to 3 : as below
Start/Hold
P.SEL1
P.SEL2
P.SEL3
pattern 1 pattern 2 pattern 3 pattern 4 pattern 5 pattern 6 pattern 7 pattern 8
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON : Shorted between COM terminal and P.SEL terminal or same level
OFF : Open between COM terminal and P.SEL terminal or 5 V
• BCD output (A6XXX-X2 TTL)
(A6XXX-X3 Open collector)
Type of output : Open collector or TTL
Logic
: Changeable
Output rate
: DC30 V 10 mA (open collector)
Funout 2 (TTL)
• Analog output (A6XXX-X4)
output
0 to 1 V
0 to 10 V
1 to 5 V
4 to 20 mA
Load resistance
Accuracy
Ripple
more than 10 kΩ
±(0.5% of F.S)
50 mV p-p
less than 550 Ω
Output method
Scaling
Resolution
Reponse time
25 mV p-p
: PWM method
: Digital scaling
: 13 bit
: approx 0.5 sec
• RS232C (Conforming to EIA RS-232C)(A6XXX-X5)
Transmission speed
Start bit
Data length
Parity
Stop bit
Character code
:Full duplex
:4800/9600/19200/38400 bps
:1 bit
:7 bit/8 bit
:Even parity/ odd parity/ none
:1 bit/2 bit
:ASCII code
:Ignord process
• RS-485 (conforming to EIA RS-485)(A6XXX-X6)
Transmission speed
Start bit
Data length
Parity
Error detection
Stop bit
Character code
Transmssion control process
Signal name
: Full duplex
: 4800/9600/19200/38400 bps
: 1 bit
: 7 bit/ 8 bit
: Even parity/ odd marity/ none
: BCC
: 1 bit/2 bit
: ASCII code
: Ignord process
: +non reversal output
-reversal output
Maximum no of meter connected : 31
Line length
: up to 500m in total
Display
: Main display Red or Green LED 20 mm
Sub display Red LED 6 mm
Conversion rate
: 1000 times/sec.
Maximum display
: 9999
Overrange indication : When input exceed the maximum display
display OVER or –OVER
Zero display
Decimal point
Operating temp.
: 0 to 50°C 35 to 85% RH
Storage temp.
: –10 to 70°C less than 60% RH
Power supply
: AC 100 to 240 V ±10%
DC 12 to 48 V ±10%
Power consumption
: 8 VA (max. load)
Dimensions
: 96 mm (W) X 48 mm (H) X 97.5 mm (D) DIN size
Weight
: approx. 450 g
AC1500 V/min.
(DC) : Power supply/input terminal/output terminal
DC500 V/min.
(Common) : Case/each terminal
AC1500 V/min.
: DC500 V more than 100 MΩ at the above terminals
Dimensions
Ordering Code
(86.5)
Option
0.
1.
2.
3.
4.
5.
6.
7.
8.
Comparator output
0. none
1. Relay
2. Photocoupler
Input
1.
2.
3.
4.
5.
6.
7.
8.
9.
A.
B.
Displayb board
1. Multiple
2. Single
Power supply
1. AC 100 to 240 V
2. DC12 to 48 V
77
(97.5)
0.5
A6
Input
Option
Power
10.9
Comparator
44.8
91.5
102.5
48
(21.5)
Muliple
92 +0.8
-0
MIN.70
45 +0.6
-0
Single
MIN.120
none
External control
BCD output (TTL)
BCD output (open collector)
Analog output
RS-232C
RS-485
RS-232C, analog output
RS-485, analog output
DC voltage
DC current
DC current
AC voltage
AC current
AC current
Resistance
Temperature (T/C, RTD)
Frequency
Strain gauge
Process
33-6, YAGUCHI 2-CHOME, OHTA-KU,
FAX
: (03)3757-2989
PHONE : (03)3579-3893
Printed in Japan, Dec. 2003 (YG)
왎 DC voltage,current
• A7X11-X
Range Measurement Range
11
±99.99 mV
12
±999.9 mV
13
±9.999 V
14
±99.99 V
15
±700 V
Conversion rate: 1000times/sec
Display
offset ±9999
full scale ±9999
Input Protection
±50 V
±50 V
±250 V
±250 V
±700 V
Accuracy (23˚C ± 5˚C, 35 ~ 85% RH)
Input Protection
±10 mA
±50 mA
±50 mA
±700 mA
Accuracy (23˚C ± 5˚C, 35 ~ 85% RH)
Input Protection
Accuracy (23˚C ± 5˚C, 35 ~ 85% RH)
±3 A
Input Protection
50 V
50 V
250 V
250 V
700 V
Accuracy (23˚C ± 5˚C, 35 ~ 85% RH)
Input Protection
10 mA
10 mA
50 mA
500 mA
Accuracy (23˚C ±5˚C, 35 ~ 85% RH)
• A7X12-X
21
±99.99 uA
22
±999.9 uA
23
±9.999 mA
24
±99.99 mA
Display
offset ±9999
full scale ±9999
• A7X13-X
25
±999.9 mA
26
±2.000 A
Display
offset ± 9999
full scale ±9999
왎 AC voltage, current (TRUE-RMS)
• A7X14-X
Range
11
12
13
14
15
Measurement Range
99.99 mV
999.9 mV
9.999 V
99.99 V
700.0 V
Display
offset ±9999
full scale ±9999
Frequency range: 40Hz to 1kHz
Response time:
Approx 1 sec(10% to 90%)
• A7X15-X
Range
21
22
23
24
Measurement Range
99.99 uA
999.9 uA
9.999 mA
99.99 mA
Display
offset ±9999
full scale ±9999
Response time:
• A7X16-X
Range
25
26
Measurement Range
999.9 mA
5A
Display
offset ±9999
full scale ±9999
Input Protection
3A
8A
Accuracy (23˚C ±5˚C, 35 ~ 85% RH)
Response time:
왎 Resistance
• A7X17-X
Range
11
12
13
14
Measurement Range
99.99 Ω
999.9 Ω
9.999 KΩ
99.99 kΩ
Display
offset ±9999
full scale ±9999
Current
5 mA
0.5 mA
50 uA
5 uA
Accuracy (23°C ±5˚C, 35 ~ 85% RH)
Maximum Resolution
0.1˚C
1˚C
1˚C
1˚C
1˚C
1˚C
1˚C
0.1˚C
1˚C
Accuracy (23˚C ±5˚C, 35 ~ 85% RH)
±(0.5% of FS)
±(0.2% of FS)
±(0.2% of FS)
±(0.6% of FS)
±(0.4% of FS)
±(0.4% of FS)
±(0.4% of FS)
±(0.15% of FS)
±(0.3% of FS)
Measurement method: Two or Four wire (internal socket changable)
왎 Thermocouple • RTD
• A7X18-X
Range
KA
KB
J
T
S
R
B
PA
PB
Sensor type
K
K
J
T
S
R
B
PT100 Ω
PT100 Ω
Linearzing method
Burn out alarm
Conversion time
Measurement Range
-50.0 to 199.9˚C
-50 to 1200˚C
-50 to 1000˚C
-50 to 400˚C
0 to 1700˚C
-10 to 1700˚C
100 to 1800˚C
-100.0 to 199.9˚C
-100 to 600˚C
: ±2˚C (10 to 40˚C)
: less than 50 Ω
: Digital linearizing
:----: 2.5times/sec
왎 Frequency
• A7X19-X
Range
11
12
13
Accuracy (23˚C ±5, 35 ~ 85% RH)
Measurement Range
0.1 to 999.9 Hz
1 to 9.999 kHz
10 to 99.99 kHz
Input type
Open collector
Logic
Magnet
Voltage
±(0.2% of FS)
Input voltage level
L: less than 1.5 V (5V, pullup)
0.3 to 30 V P-P
30 V rms to 500 V rms
Input Protection
30 V
15 V
30 V
500 V
Prescale
: 0.01 ~ 10.00
PPR
: 1~100
Power supply for sensor : 12 VDC ±10%
왎 Strain gauge
• A7X1A-X
sensor
5V
10 V
Measurement range
Accuracy
-1 to + 1 mV/V
1 to 3mV/V
-4 ~ + 4 mV/V
±(0.1% of FS) + 2 digit
Sesnor
: 350 Ω
Power supply for sensor : 5 V ± 5% (less than 15 mA)
10 V ± 5% (less than 30 mA)
Conversion speed
: 1000/sec
왎 Process
• A7X1B-X
sensor
1V
2V
2A
3A
Measurement Range
1 to 5 V
±5 V
4 to 20 mA
±20 mA
Display
Accuracy
offset: ±9999
Conversion rate :
1000times/sec
Excitation power supply : 12 VDC ±5%
24 VDC ±5% 25 mA
• HH, HI & LO, LLsetpoints output
Comparative condition:
Indication > High High setpoint
High High setpoint ⭌ Indication > High setpoint
High setpoint ⭌ Indication ⭌ Lo setpoint
Low setpoint > Indication ⭌ Low Low setpoint
Low Low setpoint > Indication
HH
HI
GO
LO
LL
Setting range
: -9999 to 9999
Hysteresis
Relay contact capacity : AC125 V 0.3 A resistive load
DC30 V 1 A resistive load
Photocoupler capacity : DC30 V 50 mA
• BCD output
Type of output : Open collector or TTL
Logic
: Changeable
Output rate
: DC30 V 10 mA (open collector)
Funout 2 (TTL)
• Analog output (PWM)
output
0 to 1 V
0 to 10 V
1 to 5 V
4 to 20 mA
Load resistance
Accuracy
more than 10 kΩ
±(0.5% of F.S)
less than 550 Ω
Output method
Scaling
Resolution
Reponse time
• RS232C (Conforming to EIA RS-232C)
:Full duplex
:4800/9600/19200/38400 bps
:1 bit
:7 bit/8 bit
:Even parity/ odd parity
:1 bit/2 bit
:ASCII code
:Ignord process
• RS-485 (conforming to EIA RS-485)
Transmission speed
Start bit
Data length
Parity
Error detection
Stop bit
Character code
Transmssion control process
Signal name
±50 mV p-p
±25 mV p-p
: PWM method
: Digital scaling
: 13 bit
: approx 0.5 sec
Transmission speed
Start bit
Data length
Parity
Stop bit
Character code
Ripple
: Full duplex
: 4800/9600/19200/38400 bps
: 1 bit
: 7 bit/ 8 bit
: Even parity/ odd marity
: BCC
: 1 bit/2 bit
: ASCII code
: Ignord process
: +non reversal output
-reversal output
Maximum no of meter connected : 31
Line length
: up to 500m in total
Maximum display
Overrange indication
: 9999
: When input exceed the maximum display
display OVER or -OVER
Zero display
Decimal point
Operating temp
: 0 to 50°C (35 to 85% RH)
Storage temp.
: -10 to 70°C less than 60%RH
Power supply
: 100 to 240VAC ± 10%
12 to 48VDC
Power consumption
: 8VA (At AC) 7W(At DC)
Dimensions
: 72mm (W) × 36mm (H) × 118mm (D)
Weight:approx
: 160g
(DC) : Power supply/input terminal/output terminal
: Input terminal/output terminal
: DC500V more than 100MΩ at the above terminals
Dimensions
AC1500 V/min
DC500 V/min
DC500V/min
Ordering Code
68
33
A7
1
–
Output
118
80
Input
RE
PH
DZ
ME
P1
P2
P3
HH
HI
GO
LO
LL
E
36
7
87
M
68 +0.7
-0
72
7.
8.
9.
A.
B.
C.
none
Relay output
Photocoupler output
BCD output (TTL)
BCD output (Open collector)
BCD output (TTL), Photocoupler output
BCD output (Open collector), Photocoupler
output
Analog output
Analog output, Photocoupler output
RS-232C
RS-485
RS-232C, Photocoupler output
RS-485, Photocoupler output
1.
2.
3.
4.
5.
6.
7.
8.
9.
A.
B.
DC voltage
DC current
DC current
AC Voltage
AC current
AC current
Resistance
Temperature (T/C, RTD)
Frequency
Strain gauge
Process
1. AC100 to 240V
2. DC12 to 48V
-0
33 +0.6
Power supply
0.
1.
2.
3.
4.
5.
6.
Min.96
3rd floor, Ehara bldg., 5-7, Kaji-cho 1-chome, Chiyoda-ku,
FAX
: (03)3251-5576
PHONE : (03)3251-5567
Printed in Japan, Feb. 2006 (KS)
UNIVERSAL TYPE DIGITAL PANEL METER
A8000
NE
■ Featuers
W!
· Power Supply : 5V to 12VDC, 12V to 24VDC
· BCD Output (option)
· 4 1/2 digit
■ Thermocouple • RTD
● A83 C-0
■ DC voltage , current
● A83 1-0
(DC voltage)
range
Measurement
Range
Display
Input
Protection
Accuracy
(23°C ± 5°C, 35 to 85%RH)
11
12
13
14
± 199.99mV
± 1.9999V
± 19.999V
± 199.99V
offset ± 19999
full scale ± 19999
± 50V
± 50V
± 250V
± 250V
± (0.1% of rdg + 2 digit)
● A83 2-0
(Thermocouple)
range
Sensor
type
Measurement
Range
Maximum
Resolution
Accuracy
(23°C ± 5°C, 35 to 85%RH)
KA
KB
J
T
S
R
B
K
K
J
T
S
R
B
-50.0 to 199.9°C
-50 to 1200°C
-50 to 1000°C
-50 to 400°C
0 to 1700°C
-10 to 1700°C
100 to 1800°C
0.1°C
1°C
1°C
1°C
1°C
1°C
1°C
± (0.5% of FS)
± (0.2% of FS)
± (0.2% of FS)
± (0.6% of FS)
± (0.4% of FS)
± (0.4% of FS)
± (0.4% of FS) applied over 500°C
Cold junction compensator accuracy :
Sensor lead resistance :
Linearzing method :
Burn out alarm :
(DC current)
range
Measurement
Range
Display
Input
Protection
22
23
24
25
± 1.9999mA
± 19.999mA
± 199.99mA
± 1999.9mA
offset ± 19999
full scale ± 19999
± 50mA
± 50mA
± 3A
± 3A
Accuracy
(23°C ± 5°C, 35 to 85%RH)
± (0.2% of rdg + 2 digit)
● A83 D-0
range
± 2°C (10 to 40°C)
less than 50Ω
Digital linearizing
-----
(RTD)
Measurement
Range
Sensor type
PA
PT100Ω
-100.0 to + 199.9°C
PB
PT100Ω
-100 to + 600°C
Maximum
Resolution
Accuracy
(23°C ± 5°C, 35 to 85%RH)
0.1°C
1°C
± (0.15% of FS)
± (0.3% of FS)
■ AC voltage, current (TRUE-RMS)
● A83 4-0
range
Display
11
199.99mV
12
1.9999V
offset ± 19999
13
19.999V
full scale ± 19999
14
199.99V
Frequency range : 40Hz to 1kHz
Response time :
Approx 1 sec (10% to 90%)
Dead band :
100 digit
● A83 5-0
range
(AC voltage)
Measurement
Range
Input
Protection
Accuracy
(23°C ± 5°C, 35 to 85%RH)
50V
50V
250V
250V
± (0.2% of rdg + 20 digit)
(AC current)
Measurement
Range
Display
23
19.999mA
offset ± 19999
24
199.99mA
full scale ± 19999
25
1999.9mA
Frequency range : 40Hz to 1kHz
Response time :
Approx 1 sec (10% to 90%)
Dead band :
100 digit
Input
Protection
Accuracy
(23°C ± 5°C, 35 to 85%RH)
50mA
3A
3A
± (0.5%of rdg + 20 digit)
Display
1V
1 to 5V
Offset : ± 19999
Fullscale ± 9999
2V
4 to 20mA
Excitation power supply : 24VDC ± 10% 30mA
● External Control
Hold:
Shorted HOLD terminal and COM terminal or
equipotential, Hold ON
Digital Zero: Shorted DZ terminal and COM terminal or equipotential,
Digital zero ON
Peak Hold: Shorted PH terminal and COM terminal or equipotential,
Peak hold ON
Red LED 10mm height
-19999 to 19999
20times/sec
When input exceed the maximum
display display OL or -OL
Zero display:
Leading zero suppression
Decimal point:
Settable to any digit position
Operating temp:
0 to 50°C (35 to 85% RH)
Storage temp:
-10 to 70°Cless than 60%RH
Power supply:
5V to 12VDC, 12V to 24VDC
Power consumption: Appro x 1.5W
Dimensions:
48mm (W) x 24mm (H) x 96mm (D)
DIN size
Weight (unit only) :
Appro x 100g
Dielectric strength:
Power supply/input terminal/output
terminal/external control
DC500V/min
Input terminal/output terminal/external
control
DC500V/min
Case/each terminal
AC1500V/min
Insulation resistance: DC500V more than 100MΩ at the above
terminals
Display:
Maximum display:
Conversion rate:
Overrange indication:
● A83 B-0
Measurement
Range
Open collector or TTL
Changeable
DC30V 10mA (open collector)
Funout 2 (TTL)
■ Common Specification
■ Process
range
● BCD output
Type of output:
Logic:
Output rate:
Input
Protection
Accuracy
(23°C ± 5°C, 35 to 85%RH)
± 50V
± 50mA
± (0.1% of rdg + 3digit)
± (0.2% of rdg + 3digit)
UNIVERSAL TYPE DIGITAL PANEL METER
A8000
■ Ordering Code
–0
A8
Option
1. none
2. BCD (TTL), external control
3. BCD (Open collector),
external control
Input
1.
2.
4.
5.
B.
C.
D.
Front sheet
1. with sheet switch
2. without print sheet swtich
Power supply
3. 5V to 12VDC
4. 12V to 24VDC
DC voltage
DC current
AC voltage
AC current
Process
Thermocouple
RTD
■ Dimensions
With sheet switch
24.0
48.0
Front View
Without sheet switch
24.0
48.0
89.1
Side
View
3.5
3rd Fl., Ehara Bldg., 5-7, Kaji-cho 1-chome,
Chiyoda-ku, Tokyo 101-0044, Japan
TEL:+81-3-3251-5576
FAX:+81-3-3251-5567
Printed in Japan, Jun. 2005 (KP)
PROCESS MONITOR
AS-201
■ Features
✽ Fullscale Adjustable
• Adjustable full scale
• Bright LED 10.2mm
• Din size 24(H) ✕ 48(W)
• 1-5V, 0-5V, 0-10V measurement
• Power supply DC5V (NO-ISOLATED)
Model Code
Range
AS-201-1V
AS-201-2V
AS-201-3V
1~5V
0~5V
0~10V
Display
Adjustable
0-100~1999
0-100~1999
0-100~1999
Input
Impedance
1MΩ
1MΩ
1MΩ
Input
Protection
±250V
±250V
±250V
■ Ordering Code
AS-201 -
Range
{
1V
2V
3V
Accuracy: ±0.1% rdg ±2 digit (23°C ±5°C)
■ Dimensions
Full-scale Adjustment:
External Hold:
Power Supply:
Operating Temperature:
Power Consumption:
Dimensions:
Weight:
Dielectric Strength:
Insulation Resistance:
73
51
4.8
Side
45 +0.6
–0
Min.35
Decimal Point:
Overrange Indication:
Front
Offset
Adjust
Fullscale
Adjust
48
22.2 +0.3
–0
Display:
Polarity:
Single Ended
2nA(Typ.)
2.5/sec
40dB Typ. (50/60Hz)
±0.1 digit (Typ.)/°C
±0.3 digit (Max.)/°C
LED, 10.2mm 3 1/2 digit
1V Range:When input less than 1V, a "-" is
displayed automatically.
2V, 3V Range:When input less than 0V, a "-"
is displayed automatically.
1999 flashes
100~1999
Negative 0V or Short
DC 5V±5% 70mA (Typ.)
0~50°C, 35 to 85%RH
350mW
24(H) ✕ 48(W) ✕ 73(D)mm DIN Size
40g
Between Input(Lo) and Mounted panel,
AC1500V/1 min.
DC500V 100MΩ or more at above terminals
Panel Cutout
Min.65
Panel thickness 0.8 to 3.2mm
Connect input Lo and Ov.
1
2
HI LO
3
HOLD
Input Configuration:
Input Bias Current:
Conversion Rate:
Normal Mode Rejection:
Temperature Coefficient:
24
Process Monitor
■ Specifications
4
101
INPUT
5
6
7
8
9
10
COM 102 103 OV +5V
D.P
Power
PROCESS MONITOR
AS-243
■ Features
✽Standard 4 1/2 Digit
• Easily adjustable offset-fullscale (Span 10000 counts)
• Bright LED, 8 mm (Red)
• DIN size 24 (H) 48 (W) mm
• Power supply DC 24 V (isolated)
• 1-5 V, 0-5 V, 0-10 V, 4-20 mA measurement
■ Dimensions
Model
Range
Display
Input Impedance Input Protection
AS-243-1V
1-5 V
1MΩ
±250V
Offset ±5000
AS-243-2V
0-5V
fullscale
1MΩ
±250V
100 to 9999
AS-243-3V
0-10 V
1MΩ
±250V
Accuracy: ±(0.1%of rdg+2 digit) (23˚C±5˚C 45~75%RH)
48
Front
24
■ DC Current Measurement
Model
AS-243-2A
Range
4-20mA
Display
Offset ±5000
fullscale
100 to 9999
Internal Resistance Input Protection
50Ω
±50mA
87
5
65
Accuracy: ±(0.1% of rdg+2 digit) (23˚C±5˚C 45~75%RH)
■ General Specifications
Fullscale adjustment :
Offset a djustment :
Span :
Display :
Polarity :
Scaling :
Hold :
Decimal point :
Operating temperature :
Power supply :
Power consumption :
Dimensions :
Weight (unit) :
Accessory :
45 ＋0.6
−0
Min.35
Side
Single ended
2 mA (TYP.)
2.5/sec
50dB (TYP.) (50/60 Hz)
Offset display ±0.5 digit/˚C
Fullscale display ±0.01% of span/˚C
display flashes
100 to 9999
±5000
10000 counts
LED, 8 mm (Red)
By switch (rear) and fine volume (front)
COM and S/H terminal shorted
0 to 50˚C 35 to 85%RH
DC24V±20%
30 mA at DC24V
24(H) 48(W) 87(D)mm DIN size
Approx. 50g
Between input (Lo) and mounted panel, AC
1500V/l min.
Between input (Lo) and power supply (0V), DC
500 V/l min.
DC 500 V 100 MΩ or more at the above
terminals
Connector, Instruction manual
22.2 ＋0.3
−0
Input configuration :
Input bias current :
Conversion rate :
Normal mode rejection :
Temp. coefficient :
Panel Cutout
Min.65
Panel thickness 0.8 to 3.5mm
1
2
3
4
HI
LO
S/H
NC
INPUT
■ Ordering Code
AS-243-
-4
Power Supply 4. DC24V
1V
Range 2V
3V
2A
{
5
6
NC COM
7
8
NC
NC
9
10
−
＋
DC POWER

asahi keiki co.,ltd.

Transcription

Similar documents

asahi keiki co.,ltd.