2006-2013 DYNA Renegade Installation Instructions

Transcription

DYNA
2006-2013 H-D FXD MODELS
Installation Instructions
*Excludes Fat Bob
July 2014
2006-2013 FXD Renegade Rev. 6
Table of Contents
SECTION
INTRODUCTION AND GENERAL INFORMATION
Unpacking Your Kit
Preparing the Motorcycle
Installing Lehman Swingarm
Carrier Assembly and Pulleys
Installing the Differential
Assembling the Carrier/Pulley Unit in the Differential
Belt Tensioning and Tracking
Attaching, Adjusting and Bleeding the Brake System
Installing the Lehman Frame & Suspension
Installing the Exhaust
Body Prep, Lights and Wiring
Fitting the Body
Door Install and Adjstment
Neck Race Preload
Renegade Torque Specifications
Replacement Parts
*2006 Dyna models use a 66 tooth pulley assembly
*2007-2013 Dyna models use a 70 tooth pulley assembly
1
INTRODUCTION AND GENERAL INFORMATION
Statements in these instructions preceded by the words WARNING, CAUTION, or NOTE and printed
in bold face are important.
** WARNING **
Indicates a strong possibility of severe personal injury or loss of life if instructions are not
followed.
** CAUTION **
Indicates a possibility of personal injury or equipment damage if instructions are not
followed.
** NOTE **
Gives helpful information to make a step or procedure easier or more clear.
Throughout these instructions, “Front” or “Forward” refers to the front of the bike. The “Left” and “Right
hand” sides refer to the position of the parts as viewed by a rider sitting on the seat, facing forward.
All of the procedures covered in the manual should be performed by Lehman factory-trained installers.
A few steps may require special skills using power tools. These steps should be completed by qualified
personnel only.
These instructions do not include information, specifications, or repair procedures relating to the
motorcycle itself. Please reference a factory service manual for motorcycle information.
The information in these instructions is provided to Lehman Trikes dealers. It is proprietary to
Lehman Trikes, Inc. and provided solely for use by dealers. Any unauthorized duplication or distribution is a
violation of international copyright law.
** NOTE **
Compliance with national (DOT-USA, MOT-Canada), State, Provincial, and local vehicle
standards is the responsibility of the installer. Installation of the parking brake is
necessary to achieve compliance with DOT/MOT.
** NOTE **
The symbol H-D refers to Harley-Davidson.
The symbol LH refers to left hand side while seated on the bike.
The symbol RH refers to right hand side while seated on the bike.
2
Unpacking Your Kit
The crate contains the following:
1.
2.
3.
4.
5.
Differential with brakes
Wheel kit.
Renegade Body.
Swingarm.
Lehman frame.
6.
7.
8.
9.
10.
Hardware box (small parts & bolt bags)
Shock absorbers.
Warranty Book.
Owners Manual.
Packing/parts list
Check your kit to the parts list and the order when it arrives.
3
MODULAR DIFFERENTIAL
4
Preparing Motorcycle
Note: During installation you will use various products on different areas of the trike. The following
are products to have on hand before starting the conversion.
Loctite 242- Medium strength blue
Loctite 262- High strength red
Loctite 5920- High temp sealer
Note: Refer to H-D service manual for detailed instructions on the removal of the following parts:
1. Note motorcycle year, model and VIN number, as well as Lehman serial number located inside body, on
left side of swingarm and on warranty registration form in owner’s manual.
2. Place motorcycle on center stand, preferably on a motorcycle lift. Secure front wheel to lift with
compression strap.
3. Remove seat and disconnect battery.
Note: Always disconnect negative battery cable first. If positive cable should contact a grounded
object while the negative cable is installed, the sparks may cause an explosion.
4. Raise motorcycle so that rear wheel is off lift.
5. Use a level on HD frame to confirm bike is straight. Locate a reference point on frame that is level.
6. Remove side stand and side covers.
7. Disconnect rear wiring harness.
8. Remove rear turn signals from fender. These will be reused with Lehman body.
9. Remove rear fender assembly from motorcycle.
10. Remove mufflers and heat shields from motorcycle, save all exhaust hardware, these parts will be reused.
11. Remove muffler support from transmission. Save hardware.
12. Remove belt cover.
13. Remove master cylinder cover. Evacuate brake fluid from system through bleeder screw on caliper.
14. Cover master cylinder to prevent contamination.
15. Remove brake line from caliper. Save banjo washers for use on Lehman brake system.
16. Remove shocks.
17. Remove rear tire and brake assembly.
18. Remove swingarm pin, discard pin and save flange nut.
19. Remove swingarm from motorcycle.
Fig. 1
20. Remove snap ring and bearing from left side
of swingarm.
21. Remove inner race, dust cap and bushing
from right side of swingarm. Note position
of parts for reassembly.
22. Support rear of motor with a jack and
remove (2) top rear motor mount bolts
through transmission case.
Caution: See Fig. 1. Plates will spring apart;
hold with clamp before removing nuts.
5
Installing Lehman Swingarm
Note: Provided they are in good working order, all original components of Harley-Davidson
swingarm may be re-used.
1. Clean and inspect original components, replace if necessary.
2. See Fig. 1. Install components into Lehman swingarm in same orientation as original swingarm.
Fig. 1
3. Install motor mount braces (LB6111) and aluminum
spacers. Long spacer (LS6126) will go on RH side and
short spacer (LS6125) will go on LH side.
4. See Fig. 2. Fasten transmission brace and spacers with
supplied (CB1270) GR. 8 bolts and (CN3053) stake nuts.
Using Loctite 262 install bolt with head on RH side of
motorcycle. Torque to 33 ft. lbs.
5. Use new pivot shaft bolt (LP6105) to align brace plates.
The pivot bolt should be free to rotate or pull out when
locknuts are tight.
Fig. 2 LB6111
Motor Mount
Brace
(RH Side)
LB6111 Brace- LH Side
6
6. 06-07 Models: See Fig. 3. Install swingarm pin brace
Fig. 3
(LB6110) to RH side of transmission housing with
Fig. 3 LB6110 Pin Brace, 06-07 Models
original hardware from case. Leave bolts for this bracket
loose until swingarm installation is complete.
7. 08-13 Models: See Fig. 4. Install swingarm pin brace
(LB6110) to RH side of transmission housing with
original hardware from case. Install (S001057- Fig. 4)
spacer between case and pin brace. Leave bolts for this
bracket loose until swingarm installation is complete.
All Models
8. Install Lehman swingarm with word “TOP” (stamped into
swingarm collar) facing upward.
Fig. 4
9. See Fig. 4.Place swingarm pivot bolt spacer
S001057 Spacer(LS6129) on RH side of swingarm between swingarm
2008+ Models
LS6129
bearing and LB6110 bracket.
10. On pivot bolt (LP6105) install a new (CW2032)
washer against bolt head.
11. Holding swingarm in place, insert pivot bolt assembly
through RH side and into swingarm and transmission
case. Start stock flange nut as bolt emerges from
bearing on LH side. Use Loctite 242 on threads.
CW2032
Torque to 150 ft. lbs.
Note: Make sure bolt end does not contact primary
case.
12. See Fig. 3. Using Loctite 242 tighten all fasteners for LB6110 swingarm pin bracket. Torque to 20 ft.
lbs.
13. Be sure swingarm moves freely up and down with no side to side movement.
7
Differential Installation
1. See Fig. 1. Attach LH adapter plate (LP1038) to
swingarm as shown. Leave hardware loose.
2. See Fig. 2. Attach RH adapter plate to swingarm as
shown with park brake bracket mounted to lower holes.
Leave hardware loose.
3. See Fig. 1 and 2. Install 3/8” nut to adjuster bolt and
thread into adapter plate from backside. Run bolt
completely into adapter plate.
Fig. 1
Fig. 2
8
Fig. 3
4. See Fig. 3 and 4. Loosely install hardware to pinch blocks
before installing differential to swingarm.
Fig. 4
9
Fig. 5
5.
6.
Support swingarm with jack stands.
See Fig. 5. With differential assembly on lift, slide
belt over LH axle tube and against center housing.
7. See Fig. 5. Set differential assembly on swingarm
adapter plates. Slide differential as far forward as
possible. Set jack stands under axle tubes.
8. Tighten pinch block hardware just enough to allow
differential to slide on swingarm adapter plates.
9. See Fig. 5. Remove upper, lower and rear housing
plates.
10. See Fig. 6. Carefully slide belt over pulley.
11. Reinstall housing plates with original hardware using
Loctite 242. Install all hardware before tightening.
Torque hardware to 17 ft. lbs.
Remove plates
Fig. 6
Install belt
10
Fig. 1
Belt Tensioning and Tracking
1.
See Fig. 1.Center differential to motorcycle frame.
Make sure distance is equal on both sides. This is
Figure H-1
critical for proper body and seat pan alignment.
2. See Fig. 2. Using adjusters, push differential
assembly back until belt has about 3/8” slack with 10
lbs. pressure at midpoint of bottom run
3. Measure between mount plates on swingarm and
welded pinch blocks on differential to ensure equal
distances.
4. Rotate pulleys forward at least 3 revolutions of rear
pulley by pulling backwards on bottom run of belt.
Fig. 2
Pull belt straight back to get an accurate reading.
Check that belt is running about 0.030” from flange on
rear pulley. Tap differential left or right to achieve this
reading.
5. Tighten socket head screws (8) that hold mount plates
to swingarm. Leave bolts loose to adjust differential.
6. Once tracking is obtained, re-check belt tension.
Drive belt deflection
Raise and lower differential assembly slowly with a
jack while checking belt tension. When tightest position is determined, apply 10lbs. of force at
midpoint of lower strand of belt. The correct deflection is 5/16” - 3/8”.
7. Correct tension by adjusting tensioner bolts equally on both sides. Any adjustment requires checking
belt tracking again.
8. Look along top of belt to check belt alignment on front pulley. There should be about 0.030” clearance
between pulley flange and belt. If adjustment is required, loosen cap screws that hold mount plate to
swingarm, and tap differential housing with a rubber mallet in desired direction. Check rear alignment
and belt tension again if adjustment is required.
Note: If necessary, apply chalk to edge of belt to aid in getting proper clearance between belt and
pulley flanges. If visible clearance cannot be obtained, be sure belt is not climbing up side of pulley
or squeaking as belt is rotated.
9.
After all adjustments are made, tighten adjuster lock nuts. Tighten left adapter plate bolts first. Then
tighten left-hand pinch block in a criss-cross pattern.
10. Tighten right hand adapter plate bolts and right hand pinch block bolts in a criss-cross pattern.
11. After all adjustments are made, tighten adjuster lock nuts and tighten pinch block bolts. Tighten pinch
blocks in a crosswise pattern. Go over both sides at least 2 times to seat blocks over pins. Torque
bolts to 25 ft. lbs.
11
Brake System
Fig. 1
CAUTION: Brakes are a critical safety component of the
trike. Verify all brake components have been properly
installed before test riding. Improper brake operation
could result in death or serious injury. Do not allow dirt
or debris to enter master cylinder reservoir. Brake pads
will need to be seated in during initial test ride.
Brake System
1. See Fig. 1. Attach brass tee to differential brace using
the following hardware.
(1) Brass Tee– CF5105
(1) Spacer– S001530
(2) 1/4” x 1-3/4” Hex Bolt– CB1100
(2) 1/4” Flat Washers– CW2005
(2) 1/4” Lock Nut– CN3042
2. See Fig. 1. Install original brake line from master cylinder
and rear braided lines to brass tee using the following
hardware. Torque banjo bolt to 16 ft. lbs.
(1) Banjo Bolt– S002022
(2) Banjo Washers- GC6002
(2) 45” M10 Braided Line– S001976
3. See Fig. 2. Install (2) braided brake lines to rear calipers
as shown. Torque bolts to 16 ft. lbs.
(2) M10 Banjo Bolt– CB6001
(4) M10 Banjo Washers- GC6002
4. Secure brake lines to swingarm with cable ties.
12
Fig. 2
Install brake lines to LH/RH
Park Brake Assembly
Note: Verify all brake lines and hardware are tight before bleeding system.
5. Add brake fluid (refer to OEM reservoir cap for brake fluid requirements) to brake system and work
brakes to fill lines.
6. Remove rubber caps on bleeder valves. Install clear brake bleeder hose over bleeder valve on caliper.
7. Pump brake pedal to build pressure. While holding the brake pedal, open bleeder valve to release
pressure and remove air from system. Repeat bleeding on both calipers until fluid is solid without
bubbles in bleeder hose.
8. Tighten bleeder valves and check for leaks.
9. Install master cylinder reservoir cap with new screws. Do not over tighten cap screws.
Park Brake Assembly
1. See Fig. 1. Install park brake cable to caliper brackets. Secure cable to bracket with cir-clip provided on
cables.
Fig. 1
Attach to
caliper
Secure to
bracket
RH Side
13
Fig. 2
1. See Fig. 2. Remove snap ring from one side of large clevis pin
on brake lever. Hold park brake lever on its side and push
release button at end of park brake lever to allow clevis pin to
slide out.
2. See Fig. 2.Place park brake lever within park brake bracket,
ensuring ratchet is secure on cross brace. Attach with large
clevis pin.
3. See Fig. 2. Attach park brake cable pulling bracket to brake
lever using small clevis pin and cotter pin.
(1) Cable Pulling Bracket– LB1294
(1) Clevis Pin– CC3106
(1) Cotter Pin- CC4017
4. See Fig. 3. Route left park brake cable above differential
and under motorcycle frame, attaching cable ties to cable
and frame, and install in left hole in handle mount.
5. See Fig. 4. Route right park brake cable up around axle
and forward to right hole in handle mount.
6. See Fig. 4. Secure both cables to upper rear pinch block
with clamp (GC0108).
7. See Fig. 5. Secure cable retaining nuts to handle mount
with 7/8” wrench.
8. Check for tire clearance.
9. See Fig. 5. Thread one 5/16” NF nut onto each brake
cable. Place threaded end of brake cables through holes in
cable bracket. Thread second nut onto each brake cable.
10. Adjust park brake cables at handle to engage at 3–4 clicks.
Note: Take up slack in cables before tightening ends to
ensure good adjustment range with threaded end of brake
cables.
Fig. 3
Left park brake cable
Fig. 6
Fig. 4
Cable routing
Attach clamp
Fig. 5
Cable retaining nuts
Adjuster nuts
14
Fig. 1
Installing Lehman Frame & Suspension
1.
2.
3.
Small spacer
See Fig. 1.Insert (4) small frame spacers (LS6130) into H-D
frame where trike frame will attach.
See Fig. 2.Set frame in place by using 3/8” x 2 1/2” bolts with
.875 rear frame spacers (LS6128). Use flat washers (CW2015)
on both sides and secure with locknut (CN3050). Bolt head
should be toward outside of frame.
Secure front of frame by using supplied 3/8” x 3” bolts
(S001080) with 1” frame spacer (LS6127) between Lehman
frame and H-D frame and a smaller spacer (LS1189) between outside of H-D frame and floorboard
brace (LB6112) with slots to top. Bolt head should be toward outside of frame. Use flat washers
(CW2015) on both sides and secure with a locknut (CN3050).See Fig. 2.
Fig. 2
15
Fig. 3
4.
5.
6.
7.
See Fig. 3. Install front frame mounting tab bolt
Front frame tab
through trike frame, spacer and H-D using the
following hardware.
(1) Spacer- S001050
(1) 1/4” x 1-3/4” Hex Bolt- CB1100
(2) 1/4" Flat Washers- CW2005
(1) 1/4” Lock Nut- CN3040
Tighten rear bolts and lower front tab bolt. Leave
upper front bolts until floorboard mounts are
adjusted.
See Fig. 4. Use 1/2" x 2-1/2” bolts to mount floor
board brackets to H-D frame. Secure using the
following hardware.
(2) 1/2" x 2-1/2” Hex Bolts- CB1417
(4) 1/2” Flat Washer- CW2015
(2) 1/2” Lock Nut- CN3060
See Fig. 5. Install cross brace between frame braces and
floorboard mounts using the following hardware. Do not
tighten floorboard mounts until later in build.
(1) Cross Brace- LB6113
(2) 3/8” x 1-1/4” Bolt- CB1240
(2) 3/8” Lock Washer- CW2050
(2) 3/8” Flat Washer- CW2015
S001050 Spacer
Fig. 4
Fig. 5
Cross Brace
Floorboard Mount
16
Note: The lower shock eye is offset to one side. Be sure to install correctly.
8. See Fig. 6.Install 1/2” x 2 1/4” bottom shock bolt and GB0320 bushings through lower shock eye, and
thread it into shock plate. Use (1) washer under head of bolt. Lock bolt in with a lock nut.
9. Raise differential and install top of shock using 1/2” x 2 1/4” bolt, GB0320 bushing and one washer
under head of bolt. Shock should run parallel to frame tube when viewed from rear. Torque shock
bolts to 40ft-lbs.
Fig. 6
17
10. See Fig. 7. Install stabilizer bar LB6101 into tab on right side of Lehman frame. Use a 3/8” NC nylock
nut, washers and grommet GG6100 to attach sway bar to frame. Leave loose.
Fig. 7
11. Attach left-hand side of sway bar to sway bar bracket (S001883) using a 3/8” NC nylock nut, (2)
washers and (2) grommets (GG6100). Shim with flat washers as needed. Leave loose. See Fig. 8.
Fig. 8
S001883
18
12. See Fig. 9. Sway bar bracket is attached to upper rear of differential housing.
Fig. 9
13. Tighten 3/8” nuts on stabilizer bar until there is no play in grommets. DO NOT COMPRESS
GROMMETS.
Caution: Make sure sway bar is not pulling or pushing on Lehman frame when trike is at rest as this
could alter power train alignment. Make sure shocks are running vertical after sway bar is
tightened. There are (6) 3/8” flat washers supplied to shim grommets on sway bar if needed.
Dyna Head Bolt Procedure (Bolt Bag LCK5064)
1.
2.
3.
4.
Remove existing 3/8” head bolts and washers from engine mount bracket on LH side.
Apply Loctite 242 to threads of 3/8” x 1 ½” hex flange locking bolts.
Assemble bolt, spacer (LS1189) and external tooth lock washer in appropriate order.
Torque bolts to 42 ft.-lbs.
19
Installing Exhaust
1.
2.
All heat shields should be removed. Mufflers, muffler support and rear bracket should be
disassembled.
Stock rear header pipe will need to be cut approximately 3 ½” back from center of cross-over tube.
Install exhaust pipes LP6100 and LP6101 onto stock header pipes. Slide exhaust clamps into position
and leave loose. Install mufflers onto Lehman exhaust pipes with muffler mounting plates pointing up.
NOTE: Lehman pipes may need to be cut depending on muffler location.
Fig. 1
20
3.
Position exhaust system with jack stand, then install muffler bracket (LB6104) to mufflers with (2) 5/16”
x 3/4” carriage bolts (CB1529) and 5/16” flange nuts. Position mount so it is pointing toward front of
motorcycle.
Install rubber isolator (GM0300) into slot on muffler bracket (LB6104).
Fig. 2
4.
Insert bracket (GB1200) into rubber isolator. Attach bracket to Lehman frame using (2) 5/16” x 1 1/2”
bolts, four (4) 5/16” flat washers, exhaust spacers (LS6101) and lock nuts.
Fig. 3
5.
6.
7.
Adjust mufflers and pipes so they run even and parallel to one another.
Fasten exhaust clamps to joint. Position clamps so they do not squeeze a slit open on the sides, and
clamp opening does not line up with slits in pipe.
Inspect exhaust system for exhaust leaks and install heat shields. Trim rear head pipe head shields
as needed.
21
Fig. 1
Body Prep, Lights and Wiring
1.
2.
3.
4.
5.
6.
Drill (2) 5/16” holes for signal mounting; (1) for wire
and (1) for mounting bolt.
See Fig. 1.Mount HD factory turn signals on flat below
taillights. Center turn signal with inside edge of
taillights.
NOTE: Do not over tighten taillight mounting
hardware. Damage to housing may occur.
See Fig 2. Mount taillight assemblies to body with
gaskets. Attach ground wire to stud with flange nut after
taillight mounting hardware is installed.
(2) Taillight Assembly-S002204
(2) Gaskets– BG0200
(4) 1/4” Flat Washer– CW2006
(4) Lock washer– Provided with light
(4) Nut– Provided with light
(2) 1/4” Flange Nut– CN3007
If required- Install female terminals and male connectors
to taillight wiring Use appropriate tool for crimping
terminals to wires. (Mac Tools– TCT1028).
Inspect crimps before installing into connector. Distortion
should be minimal.
See Fig. 3. Install thin weather seal (CW2505) on bottom
outside edge of seat shell.
7. See Fig. 3. Install 1/4” studs to seat shell using Loctite
242.
(5) 1/4” Studs- S001343
8. Install seat shell to body with flat washers and flanged
lock nuts.
(5) 1/4” Washers- CW2005
(5) 1/4” Flange Lock Nuts- CN3007
Fig. 2
Attach ground wire to stud
Fig. 3
Install studs
to seat shell
Apply trim to
seat shell
22
Fig. 3
Fig. 4
23
Renegade Wiring Harness
1. See Fig.’s 1-2. Attach wiring harness to body clips on
underside of body.
2. Connect 8 position connector on wiring harness (Fig. 3)
to OEM harness, located under rider seat at rear of
OEM frame.
Fig. 1
Taillight connector
Light bar
connector
on RH side
Body clips
Fig. 2
Fig. 3
8-position connector on wiring harness-main
Body clip
License plate connector
6-position connector on wiring harness for trailer
3. See Fig.’s 4-5. Before connecting license plate and light bar (optional) to harness, terminals and
connectors will need to be installed to each before connecting to wiring harness. Use appropriate tool
for crimping terminals to wires. (Mac Tools– TCT1028, Blue Point– PWC47 or H-D 41609).
4. See Fig. 5. Inspect crimps before installing into connector. Distortion should be minimal.
Fig. 4
Fig. 5
Insulation crimp
Male terminal
Wire core crimp
Female terminal
24
Fig. 1
Body Installation
Note: To meet DOT and MOT requirements one of the following
must be installed- stock grab handles, stock grab strap or
Lehman-supplied grab handles.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
Install seal
to boards
Position body on frame so that wheel clearance is equal on both
sides and front of each fender is an equal distance from front of
each tire. Center tire in wheel cut-out when viewed from side.
Shims are provided to level body to frame.
Insert (3) (CW2097) rubber body washers between frame and
bottom of trunk.
See Fig. 1.Install thin weather seal (CW2505) on edge of
Fig. 2
floorboards and set them in place
Install ¼” x ¾” bolts (CB1080) with washers (CW2006) through
body and into foot pocket inserts.
Align steel mounting bracket to foot pocket and install ¼” x 1”
bolts (CB1086) and washer (CW2006) through center mounting
hole with washer and locknut (CN3041) on bottom. Leave loose.
See Fig. 2. Once foot pocket is aligned, drill holes through
existing holes in body into foot pocket. Use ¼” x 1” bolts
(CB1086) with bolt head on foot pocket side, through body and
secured with washer (CW2006) and locknut (CN3041).
Tighten front frame bolts and foot pocket mounting bracket.
Tighten all foot pocket mounting hardware.
Fig. 3
Install rubber footpads through foot pocket and mounting bracket
using washers (CW2005) and locknuts (CN3040)..
Verify that body is still square with motorcycle.
From underside of body, drill a ¼” hole in body through each of
four mounting tabs. Keep hole centered in slot of each of tabs.
Fasten body as follows:
a) (4) ¼” x 2” NC button head bolts (CB1099), ¼” x 1 ¼” fender
Tapered ends to
washers (CW2108) and (FG1002) foam sealing washers install
inside of handle
from inside trunk.
b) (CW2097) rubber body washers between frame and bottom
of trunk
Fig. 4
c) (4) ¼” flat washers (CW2006)and locknuts (CN3040)
underneath frame tab to secure body to frame
Install seat insert
See Fig. 3.Grab handles- place rubber standoff (S001701)
between grab handle and body.
Install grab handles (S001035) to body using (4) 5/16” x 1”
socket head bolts (CB1159), (4) lock washers (CW2047) and (4)
fender washers (CW2109).
Place seat on trike. Center rear mounting tab on seat shell and
mark hole. Using a 19/64” bit, drill mounting hole into seat shell.
Drill hole at least 7/8” deep.
See Fig. 4.Install brass seat insert (FI0010) into shell: fit should
be tight
Place seat back on trike and secure with bolt (S001077) and washer (CW2006).
25
License Plate Light
Fig. 5
1. See Fig. 5. Install license plate bracket to door with 1/4” x
1” bolts, washers, lock nuts and rubber washers. Use
rubber washers between bracket and door. Install U-nuts
to bracket
(2) 1/4” x 1” Button head bolt (CB1086)
(2) 1/4” Rubber washer (FG1002)
(2) 1/4” Flat washer (CW2005)
(2) 1/4” Lock nut (CN3040)
(2) 1/4” U-nut (CN3301)
2. See Fig. 6. Install license plate light and support plate to
bracket using (2) 1/4” x 1 bolts.
3. See Fig. 5. Run wiring through lower hole in door.
Install rubber washers
between bracket and door
U-nut
Install wire through lower hole
Fig. 6
(1) License plate light (S001469)
(1) Support plate (S001601)
(1) 1/4” x 1 Button head bolt (CB1086)
(2) M6 Flat washer- CW2175
4. See Fig. 6. Install lower license plate mounting hardware
into place on support bracket using 1/4” x .50” bolts and (2)
lock nuts
(2) 1/4” x .50 Button head bolt (CS4032)
(2) 1/4” Lock nut (CN3040)
5. Solder and heat shrink light wiring to trunk wiring harness.
Attach wire as followsBlack wire on light to Black wire on trunk harness
Red wire on light to Red wire on trunk harness
6. Seal wiring through door with silicone (Ultra Black).
26
Fig. 1
Trunk Door Installation
Note: Lip on weather seal will face away from door opening;
top of seal is flush with top of door.
1.
See Fig. 1.Install (1) 6’ weather stripping (CW2536) around
edge of body, starting at center on bottom. Trim using
scissors; glue ends together.
2.
See Fig. 2.Insert cable through top bend on stop bracket
(FB1036). Make a small loop in the end of (1) cable
(S001686) and crimp using (1) aluminum clip CC1900
(see inset figure M-2). There should be 7-1/2” between
the stop and pre-made end of lanyard. See Fig. 2.
3.
Apply masking tape to body just below hinge mounting
holes to prevent scratching of paint by hinges.
4.
See Fig. 3.Install (2) door hinges (GH0093) and stop
cable brackets to body with (2) hinge gaskets (FG1003)
underneath hinge using (4) screws (CS4024-0) and (4)
plated star nuts (CN1898).
5.
Fasten door to hinges using (4) 10/32 x 3/8” screws
CS4024-1.
6.
Attach stop cables to door using (2) 1/4”-20 x .438” shoulder
screws (CB1151) with flat washers under cable.
7.
See Fig. 3.Torque shoulder screws to 10ft-lbs using 5/32”
Allen socket.
8.
Install latch cable bracket onto key switch.
9.
Install rear door key latch using 7/8” wrench and adjust
bracket in an upright position.
10.
See Fig. 4.Attach cable to key mechanism while key is in
vertical position with head of screw from cable facing out.
Note: Tape emergency release cable to inside front of body
during body installation.
Fig. 2
Insert through bracket
Loop and crimp
7 1/2”
Fig. 3
Shoulder Screw
Washer under
cable end
Fig. 4
Cable bracket
Key switch
27
11. See Fig. 5. Install (1) striker pin GL2041 to (1) striker pin
bracket LB1297 using (1) 5/16” plated lock nut CN3045.
12. Attach striker pin bracket to door using (2) 1/4” lock washers
CW2040 and (2) 1/4 -20 x 1/2” bolts CB1075.
13. Install (1) Renegade badge to bottom right side of door.
14. Install (1) Lehman badge GB1320 to bottom left side of door.
15. Fasten door to hinges using (4) 10/32 x 3/8” screws CS4024-1.
16. Attach stop cables to door using (2) 1/4”-20 x 1/2” hex head
bolts CB1075 (from body bolt bag) and (4) 1/4” Gr. 8 washers
CW2005.
17. Cut license plate wire from body to length (approx 12-14”)
18. Install shrink tubing over license plate wires.
19. Strip and solder ends of license plate wires from the body and door together.
20. Slide shrink tubing over soldered connections and heat.
21. Fasten wiring to trunk door.
Fig. 5
Striker pin
and bracket
28
Final Assembly
1. Reflectors can be installed to body. See Fig. 1. Install
rear reflector 3” below taillights on body. See Fig. 3.
Install side reflectors using wheel center caps as a
reference, ¼” above wheel opening on body.
2. Install rear wheels. Torque lug nuts to 85 ft.-lbs. (wire
wheels 75 ft.-lbs.)
Fig. 3
28
2006-2013 FXD Renegade
Door Adjustment Procedures
Fig. 1
Figure 0-10
29
Fig. 2
Fig. 3
30
Neck Race Preload
Steering head should be approximately twice as tight as factory specifications for a trike conversion. Refer
to H-D service manual for adjustment procedure.
Caution: Do not tighten bolts past factory specifications. Only bearing adjustment collar should be
tightened past factory settings.
31
Renegade Torque Specifications
Park brake bracket
Pinch block bolts
Head bolts
LP1038 adapter plate
Banjo bolts
LB6111 Transmission Brace Bolts
LB6110 Swingarm Pin Brace
Shock bolts
Wheels aluminum
Wheels wire
Caliper to bracket bolts
Caliper bracket to axle flange bolts
Axle tube bolts
Differential housing plate bolts
31 ft-lbs
25 ft-lbs
42 ft.-lbs
31 ft-lbs
16 ft-lbs
33 ft-lbs
20 ft-lbs
40 ft-lbs
85 ft-lbs
75 ft-lbs
38 ft-lbs
38 ft-lbs
38 ft-lbs
17 ft-lbs
32

2006-2013 DYNA Renegade Installation Instructions

Transcription

Similar documents

How to Tie a Woggle

lnstallation - ConservationMart.com

Street Magic® M109 Lowering Links Installation

Turkey - EOPOWER

CV7276 Dyna Fairing Mount Installation Instructions

to View / Print Pullback Riser Instructions

Key - Scioly.org

Installation Guides- RoofTrac® Rail System, Bonding Grounding

RÉSoNANSS: a regional contribution to

Real Time Control of Hand Prosthesis Using Surface EMG