CV7276 Dyna Fairing Mount Installation Instructions

DYNA Fairing Mount
CV7276
EXCEPT FXDWG & FXDF
Note: Inner, Outer Fairing and Radio Caddy must be purchased
separately.
ALL FIBERGLASS PARTS MUST BE PREFITTED BEFORE
PAINTING. CYCLE VISIONS IS NOT RESPONSIBLE FOR THE COST OF PAINTING.
Fits Dyna 06-10 All Models with 49 mm forks tubes
Parts Included:
1-Bottom Support
1- Fairing Mount Plate
2- Side Plate (LH & RH)
2- Support Plates (Upper & Lower)
2-5 inch foam tape
1-5/16 Flat Washer
1-5/16-18 x 1 Cap Screw
10-5/16-18 x 3/4” Button Head Alloy
5-5/16-18 Flange Nuts
1- 5/16-18 x 4 ½ Bolt
4-5/16-18 x 1” Chrome Button Head
1. Remove seat.
2. Remove gas tank bolts. Disconnect fuel line and slide gas tank back.
3. Remove headlight and extend wires 10”.
4. Remove electrical harness shield (HD Part # 70427-06) from bottom of the backbone and
discard.
5. Disassemble Fairing bracket and install the left and right side plates through the triple trees and
temporarily hold in place with the 5/16-18 x 4 ½ bolt through the gas tank mounting bracket.
See Fig 1
6. Install the left and right side plates using 2-5/16 x ¾” Alloy Button head bolt into the existing hole
vacated by the electrical harness shield. See Fig 2 & 3. Torque to 35 foot-pounds.
7. Remove the 4 ½ bolt and reinstall gas tank with the 4 ½ bolt in front and the stock bolt in the
rear.
8. Install the top and bottom fairing support brackets with the 5/16-18 x ¾ button head bolts
ensuring that the headlight wiring extends between the brackets. See Fig 4 & 5.
9. Install the face plate and route the wires through the hole in the face plate. See Fig 6.
10. Install the inner fairing and radio caddy using 4-5/16-18 x 1” Chrome button head bolts and nuts.
Install the enclosed foam tape on the leading edge of the radio caddy. See Fig 7.
11. Install the lower support bracket.
12. Install the outer fairing.
13. Install bottom fairing support bracket by installing the 4-5/16-18 button head alloy side bolts
through the fairing and one through the center bracket loosely.
14. Tighten the 4 side bolts FIRST, then the center bolt to the frame
All Harley Davidson‚ parts listed below are required for Fairing Mount kit installation, and must be purchased separately:
Inner fairing (P/N 58735-98A)
Outer fairing (P/N 58733-98A)
Dual headlamp assembly (P/N 67775-01A)
Speaker grill LH (P/N 77022-98)
Speaker grill RH (P/N 77021-98)
Stud plate (2) (P/N 31733-98))
Radio caddy (P/N 77078-98)
Cover plate (2) (P/N 31735-98)
Acorn nut (4) (P/N 31589-80)
Well nut (5) (P/N 5207)
Washer (4) (P/N 6716
Screw (2) (P/N 2995)
Screw (10) (P/N 3732)
Windshield (P/N 57958-98)
Windshield trim (P/N 58705-98A
Windshield screws (5) (P/N 933
Windshield washers (5) (P/N 6054
Lamp plug (P/N 68705-93A)
DO NOT INSTALL THIS UNIT WITHOUT APPLYING LOCKTITE
TO EVERY SCREW, NUT OR BOLT!
Our Warranty Policy
Cycle Visions’ obligation under “Our Warranty Policy” is limited to one (1) year from date of purchase to repair or replacement of the defective item (s). Chrome, polished,
powder-coated, anodized finishes, or electrical parts are limited to thirty (30) day from date of purchase.
This warranty will be void on all products that show evidence of misapplication, improper installation, abuse, lack of proper maintenance, negligence, or alteration from their
original design.
The consumer will be responsible for removing from the vehicle any defective item (s), transportation costs prepaid and for reinstallation upon return by Cycle Visions. The loss
of use of the product, loss of time, inconvenience, commercial loss or consequential damages is not covered. Cycle Visions reserves the right to change the design of any
product without assuming any obligation to modify any product previously manufactured. Warranty returns of Cycle Visions products are few because of our high quality
products.
Carefully inspect all parts…. If you find that your parts arrived in damaged conditional all original packaging material (box and other materials) must be saved to make a proper
damage claim within seven (7) days. You must be able to present the damaged boxes and materials to the freight carrier to verify your claim. The user shall assume all legal,
personal, injury risk and liability and all other obligations, duties and risks associated therewith.
Cycle Visions‰
San Diego, CA (619) 295-7800
www.cyclevisions.com
See our other products on the web!
Made in the USA
Rev 7/10
Fig 1
Fig 2
Fig 3
Fig 4
Fig 5
Fig 6
Fig 7