DDM3513 User Guide

Transcription

DDM3513 User Guide

Ubee Interactive®
DOCSIS 3.0 Cable Modem
Model: DDM3513
User Guide
Version 10_30_10
Ubee DDM3513 Cable Modem User Guide, v10_30_10
Contents
1 SAFETY GUIDELINES............................................................................................................................................ 3 1.1 ECO-ENVIRONMENTAL STATEMENTS .................................................................................................................... 3 2 INTRODUCTION ..................................................................................................................................................... 4 2.1 GENERAL FEATURES ............................................................................................................................................. 4 2.2 DEVICE SPECIFICATIONS ....................................................................................................................................... 4 2.3 PACKAGE CONTENTS ............................................................................................................................................ 6 2.4 MINIMUM REQUIREMENTS .................................................................................................................................... 7 2.5 BACK PANEL CONNECTORS .................................................................................................................................. 8 2.6 CABLE MODEM LEDS ........................................................................................................................................... 9 3 WEB-BASED DEVICE MANAGEMENT UTILITY .......................................................................................... 11 3.1 PC REQUIREMENTS ............................................................................................................................................. 11 3.2 CONNECT THE DEVICE ........................................................................................................................................ 11 3.3 ACCESS THE WEB INTERFACE ............................................................................................................................. 12 3.4 CABLE MODEM INFORMATION ............................................................................................................................ 14 3.5 STATUS................................................................................................................................................................ 15 3.6 DOWNSTREAM..................................................................................................................................................... 16 3.7 UPSTREAM .......................................................................................................................................................... 17 3.8 UPSTREAM BURST ............................................................................................................................................... 18 3.9 EVENT LOG ......................................................................................................................................................... 20 4 TOOL PAGE ............................................................................................................................................................ 21 4.1 RESET DEFAULTS (FACTORY DEFAULTS) ........................................................................................................... 21 4.2 RESET MODEM .................................................................................................................................................... 22 Ubee Interactive
2
1 Safety Guidelines
The following information provides safety guidelines for anyone installing and maintaining the DDM3513 cable
modem. Read all safety instructions in this guide before attempting to unpack, install, operate, or connect
power to this product. Follow all instruction labels on the device itself.
•
Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury.
•
To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near
water. Never spill any form of liquid on or into this product. Do not use liquid cleaners or aerosol
cleaners. Use a soft dry cloth for cleaning.
•
Do not insert any sharp object into the product’s module openings or empty slots. Doing so may
accidentally damage its parts.
•
Only use the power adapter supplied with the device. Do not attach the power supply cable on building
surfaces or floorings.
•
Do not place heavy objects on top of the device.
•
Set the power cable freely without any obstacle or heavy items piled on top of it. Refrain from abusing,
stepping or walking on the cable. Do not place the device on an unstable stand or table; the device
may drop and become damaged.
•
To protect the equipment from overheating, do not block the slots and openings in the module housing
that provides ventilation. Do not expose this device to direct sunlight. Do not place any hot devices
close to this device, as it may degrade or cause damage to it.
•
Exercise caution when installing or modifying telephone lines. Never install telephone wiring during
inclement weather conditions (i.e., storm).
•
Electrostatic discharge (ESD) can permanently damage semiconductor devices. Always follow ESDprevention guidelines for equipment handling and storage.
1.1 Eco-Environmental Statements
The following eco-environmental statements apply to the DDM3513 cable modem.
Packaging Collection and Recovery Requirements:
Countries, states, localities, or other jurisdictions may require that systems be established for the return and/or
collection of packaging waste from the consumer, or other end user, or from the waste stream. Additionally,
reuse, recovery, and/or recycling targets for the return and/or collection of the packaging waste may be
established. For more information regarding collection and recovery of packaging and packaging waste within
specific jurisdictions, contact Ubee Interactive at www.ubeeinteractive.com.
Ubee Interactive
3
2 Introduction
Welcome to the Ubee family of data networking products. This document provides instructions on how to
connect and use the Ubee DDM3513 Cable Modem. The DDM3513 Cable Modem provides high-speed
access to the Internet using an active Internet connection provided by your cable service provider.
2.1 General Features
The cable modem includes the following features:
•
Two-way design allows the cable modem to send and receive data over the cable television network.
•
Data Over Cable Service Interface Specification (DOCSIS™) 3.0 certification ensures interoperability
with DOCSIS compliant cable operators.
•
Cable bandwidth allows up to 4 bonded downstream channels and 4 bonded upstream channels,
allowing data rates of up to 152 megabits per second (Mbps)* downstream and up to 108 Mbps*
upstream, which is faster than traditional DOCSIS 2.0 cable modems, integrated services digital
network (ISDN), or asymmetric digital subscriber line (ADSL).
•
Using the cable line means that the cable modem is always on, always connected, and does not tie up
your phone lines.
*Note: The following causes may affect the connection speed.
•
Computer specification, including available RAM space and processor speed.
•
Software applications that may be using computer’s resources.
•
Network traffic depending on the time of day.
•
Max data rate set by your Cable Service Provider based on your service tier.
2.2 Device Specifications
Interface
•
RF Interface: External F-Connector
•
CPE Interface: 10/100/1000 Base Ethernet RJ45
Downstream
•
Frequency Range: 88 MHz ~ 1002 MHz
•
Modulation: 64 / 256 QAM
•
Maximum Data Rate 4DS: 171 Mbps (152 Mbps)
•
RF Input/Output Power: -15 to +15 dBmV
•
Input Impedance: 75 Ω
•
Channel Bandwidth: 6 MHz
Ubee Interactive
4
Upstream
•
Frequency Range: 5 MHz ~ 42 MHz
•
Modulation: QPSK, 8, 16, 32, 64 QAM, 128 QAM (S-CDMA only)
•
Maximum Data Rate 4 US: 122 Mbps (108 Mbps)
RF Output Power
•
TDMA /ATDMA:
+8 to +54 dBmV (32QAM, 64QAM) – ATDMA only
+8 to +55 dBmV (8QAM, 16QAM)
+8 to +58 dBmV (QPSK)
•
S-CDMA:
+8 to +53 dBmV (all modulations)
Network Management
•
SNMP v1/v2/v2c and v3 agent Built-In
•
Telnet
•
Web UI
•
IPv4 and IPv6 support
Physical Specifications
•
Dimensions: (8.44” (W) x 6.48”(D) x 1.69” (H)
•
Power: 12V/1A (Energy Star V – begin Jan-2010)
•
Power Consumption: < 10W(Full load)
•
Input Power: 100-120VAC, 50-60Hz
•
LEDs: Power, Send, Receive, Sync, Ready
Certifications
•
Safety: UL 60950; CE/ FCC Class B
•
Others: RoHS, WEEE
Standards
•
DOCSIS 3.0/2.0/1.x Certified
Environment Conditions
•
Operating temp: 0˚ C to 40˚ C (32˚ F to 104˚ F)
•
Humidity: 5~95% (non-condensing)
•
Storage temp: -40˚ C to 70˚ C (-40˚ F to 158˚ F)
P & E Witness Testing – approved by Comcast
Ubee Interactive
5
2.3 Package Contents
The DDM3513 product package contains the following:
DDM3513 Front View
DDM3513 Rear View
DDM3513 DOCSIS 3.0 Cable Modem
Firmware – 3.10.1203, Firmware approved by Comcast QA
DOCSIS 1.x/2.0/3.0 Certified
Straight-through Ethernet Cable, RJ45
Wall-wart adapter - AC to DC Power Switching
Input:
100-120VAC 50/60 Hz 0.3A
Output: 12V / 1.0Amp
Energy Star Level V beginning Jan-2010
Wall-mount instructions & template.
Ubee Interactive
6
2.4 Minimum Requirements
The following are the system requirements for computers connecting to the cable modem and for using the
web interface of the cable modem.
PC – Minimum System Requirements
Processor
300Mhz
Operating System
Windows 2000 pro, Windows XP
Memory
128 MB RAM
Hard Drive
125 MB free space
Disk Drive
CD-ROM drive
Email Client
Outlook Express 5.5/6
Internet Browser
Internet Explorer version 5.5, 6 (sp1+sp2)
Computer Interface Ethernet
Ethernet based connection (Network Interface
card
Card) that can support 10/100/1000Mbps
connection rates
Screen Display
SVGA display 800x600x256 colors or greater
Apple Mac - Minimum System Requirements
Processor
Power PC 300Mhz +
Operating System
Mac OS 9.0+ (including OSX)
Memory
64 MB RAM
Hard Drive
150 MB free space
Disk Drive
CD-ROM drive
Email Client
Mac Mail
Internet Browser
Safari 1.2 +
Computer Interface
Ethernet based connection (Network Interface
Card) that can support 10/100/1000Mbps
connection rates
Screen display
Ubee Interactive
SVGA display 800x600x256 colors or greater
7
2.5 Back Panel Connectors
Power
This is where you plug in the included power adapter. Remember to use only the
power adapter that came with the cable modem.
1000BaseT
This is where you plug in the included Ethernet cable. The other end connects to the
Ethernet port on the PC or NIC.
Reset
Allows you to power-cycle the cable modem. This function does NOT reset to
factory defaults. Use the device web interface or settings in the CM Configuration
File to reset CM to factory defaults.
Cable
This is where you connect the coaxial cable (not included) that leads to the cable
splitter (not included) or the cable wall outlet.
Ubee Interactive
8
2.6 Cable Modem LEDs
This section describes the functions of the cable modem’s LEDs and connectors. When the Power and Ready
LEDs are illuminated, the cable modem is working properly. The following tables provide an overview of the
LEDs on the front of the cable modem and what each LED represents.
Note: The above LED pattern indicates Online Ready (Green), 2 to 4 Bonded Downstream Channels Being
Used (Blue) for Increased Speed to the Internet/Cable Network, 1 Upstream Channel (Green), 1000Mbps
Ethernet (Blue), and Power ON (Green).
LED Name
DS
Ready
Provisioning State
single
US
bonded
single
bonded
Ethernet
Driver init
off
off
off
DS scanning
off
blink
off
on
DS locked
off
on
off
on
US ranging
off
on
blink
on
US ranged
off
on
on
blink
on
on
IP Init & Registration
(& Firmware Upgrade)
Operational
Network
Access
Enabled
on
Network
off
Access
Disabled
Cable interface traffic
(network access
enabled)
on
off
Power
on
on
on
on
on
on
depends
on
on
Ethernet
status
on
on
on
on
on
on
on
depends
on
on
Ethernet
status
on
on
on
Ethernet connected
depends on provisioning state
on
on
Ethernet traffic
depends on provisioning state
blink
on
Ubee Interactive
9
•
GREEN Ethernet LED indicates 10/100 Mbps speed has been negotiated.
•
BLUE Ethernet LED indicates 1000Mbps speed has been negotiated.
•
LED flashing indicates network traffic on the active port.
•
LED dark indicates no connectivity.
Ubee Interactive
10
3 Web-Based Device Management Utility
Use this chapter to access and use the U10CO35 web management utility.
3.1 PC Requirements
Be certain that your PC adheres to the following requirements. Refer to page 7 for more information on system
requirements:
Supports TCP/IP, Supports DHCP, Web browser installed
3.2 Connect the Device
Use the following procedure to connect the U10CO35 cable modem.
1. Connect the power adapter that is included with the product package to the U10CO35 and to the
power outlet.
2. Connect one end of a network cable to your computer’s Ethernet port. Connect the other end to the
100BaseT port on the U10CO35.
3. Turn on your computer.
Ubee Interactive
11
3.3 Access the Web Interface
Use the following procedure to access the web interface.
1. From the computer, launch an internet browser.
2. In the internet browser, enter the following address and press <Enter/Return>:
http://192.168.100.1
Note: You may also access the web interface using the cable/RF IP address, offered to the modem
via DHCP during registration.
3. The Cable Modem Information screen, shown below, displays key information regarding the device.
4. Click Login on the left side of the screen. In the Login pop-up window that displays, enter the login
credentials as shown below:
Admin (Privileged) Account:
Username: admin
Password: cableroot
Customer/User Account:
Username: user
Password: user
Ubee Interactive
12
5. Click OK after entering the login. Note: The Web Interface page displays the
message“401Unauthorized” when the username or password is incorrect.
6. The following navigation screen displays after logging in to the web interface. All menu functions for
the web interface are explained in the following sections.
Note: The Tools menu (upper-right side of screen) is displayed only when the admin login is used to
access the web interface.
Ubee Interactive
13
3.4 Cable Modem Information
Use the following procedure to review key information about the cable modem.
1. Access the web interface. Refer to page 12 for instructions if required.
2. Click Information from the left-side of the screen.
3. A complete description of this screen is provided following the example below.
Item
Description
Cable Modem
Indicates that the cable modem is
Docsis1.0/Docsis1.1/Docsis2.0/Docsis3.0 compliant.
MAC Address
Displays the MAC address of cable modem.
Serial Number
Displays the serial number of cable modem (usually the
MAC address without “:” between octets).
Boot Code Version
Displays the current boot code version.
Software Version
Displays the current software version.
Hardware Version
Displays the current hardware version.
CA Key
Indicates if a Certificate Authority (CA) key is installed or
not.
Ubee Interactive
14
3.5 Status
Use the following procedure to review the operational status of the cable modem.
2. Click Status from the left-side of the screen.
3. Instructions are provided below the following example.
Item
Description
Acquired a Downstream
Channel
Displays the current downstream lock status. The Status
field displays the downstream frequency. If the Comments
field displays Locked, the cable modem is locked onto the
frequency. Otherwise, it displays In Progress (the cable
modem is trying to lock on to a frequency).
Ranged Upstream Channel
Displays the current upstream ranging status. The Status
field displays the currently locked upstream frequency, and
the Comments field displays the ranging status of an
upstream lock.
Provisioning State
Displays the current cable modem state. The Status field
displays OK, cable modem is operational. Otherwise, it
displays In Progress. The Comments field displays the
current provisioning state.
Ethernet Link Status
Displays the current link status of the Ethernet interface.
The Status field displays Up/Down to indicate if there are
devices (for example, PCs) connected to the Ethernet
interface. The Comments field displays speed and the
duplex type of connected devices.
Ubee Interactive
15
3.6 Downstream
Use the following procedure to review detailed information regarding the cable modem’s acquisition and use of
downstream channels from the service provider.
2. Click Downstream from the left-side of the screen.
Item
Description
Frequency
Displays the current cable modem downstream frequency
(Hz).
Lock Status (QAM Lock/FEC
Lock/MPEG Lock)
Displays the current cable modem downstream lock status.
It contains three sub-items, QAM Lock, FEC Lock, and
MPEG Lock.
Channel ID
Displays the current locked downstream channel ID.
Modulation
Displays the current locked downstream modulation type
(QAM64/ QAM256).
Symbol Rate (Msym/sec)
Displays the current locked downstream symbol rate
(QAM64 is 5.056941 Msym/sec, QAM256 is 5.360537
Msym/sec).
Interleave Depth
Displays the current locked downstream interleave
characteristics. I is number of taps, and J is the increment.
Power Level (dBmV)
Displays the current locked downstream received power
(dBmV).
RxMER (dB)
Displays the current locked downstream Modulation Error
Rate (MER).
Correctable Codewords
This field displays R-S codewords received on this channel
with correctable errors.
Ubee Interactive
16
Uncorrectable Codewords
This field displays R-S codewords received on this channel
with uncorrectable errors.
Refresh
Click to re-display the current state of information in this
screen.
3.7 Upstream
Use the following procedure to review detailed information regarding the cable modem’s use of upstream
channels to the service provider.
2. Click Upstream from the left-side of the screen.
Item
Description
Channel Type
Displays the current locked upstream channel type. It may
be 1.0/2.0/mixed/3.0 according to collected UCDs.
Channel ID
Displays the current locked upstream channel ID.
Frequency (Hz)
Displays the current locked upstream frequency.
Ranging Status
Displays the current locked upstream ranging status
(Other/Aborted/Retries Exceed/Success/Continue/T4
Timeout)
Modulation
Displays the current locked upstream modulation type
(QPSK/ 8QAM /16QAM/
32QAM/64QAM/128QAM/256QAM).
Symbol Rate (Ksym/sec)
Displays the current locked upstream symbol rate.
Ubee Interactive
17
Mini-Slot Size
Displays the current locked upstream mini-slot.
Power Level (dBmV)
Displays the current locked upstream transmit power.
T1 Timeouts
Displays the number of timeouts waiting for a valid UCD
from the CMTS.
T2 Timeouts
Displays the number of timeouts waiting for a maintenance
broadcast from the CMTS.
T3 Timeouts
Displays the number of timeouts waiting for ranging request
from the CMTS during initial maintenance.
T4 Timeouts
Displays the number of timeouts waiting for periodic
maintenance request from the CMTS for unicast ranging
opportunity.
Refresh
Click to re-display the current state of information in this
screen.
3.8 Upstream Burst
Use the following procedure to review detailed information regarding the cable modem’s upstream burst
attributes.
2. Click Upstream Burst from the left-side of the screen.
Item
Description
Modulation Type
Displays the current modulation type
(QPSK/16QAM/8QAM/32QAM/64QAM/128QAM) used for
transmission of specific traffic types (maintenance, short
packets, long packets, or unsolicited grants, such as those for
voice traffic).
Ubee Interactive
18
Item
Description
Differential Encoding
Displays the current differential encoding state (ON/OFF).
Preamble Length
Displays the current preamble length, 0-1536 (bits) used for
synchronization.
Preamble Value Offset
Displays the current preamble value offset, 0-1534 (bits).
FEC Error Correction (T)
Displays the FEC (forward error correction): 0 to 16 (0 implies
no FEC. The number of codeword parity bytes is 2*T).
FEC Codeword Information
Bytes (k)
Displays the current FEC codeword information bytes.
Fixed: 16 to 253 (assuming FEC on). Shortened: 16 to 253
(assuming FEC on).
Maximum Burst Size
Displays the maximum burst size, 0-255 (mini-slots) for data
transmission
Guard Time Size
Displays the guard time size, 4-255 (symbols).
Last Codeword Length
Displays the last codeword length, FIX/SHORT.
Scrambler on/off
Displays the state of the scrambler, ON/OFF.
Refresh
Click to re-display the current state of information in this screen.
Ubee Interactive
19
3.9 Event Log
Use the following procedure to review the event log generated by the cable modem. The event log captures all
key behavioral activity of the cable modem.
2. Click Event Log from the left-side of the screen.
Item
Description
Refresh
Update events in the log as they occur.
Clear Log
Empty the event log.
Ubee Interactive
20
4 Tool Page
The Tool options of the web interface allow you to reset/power cycle the cable modem or perform a factory
default.
Important: You must log in using the admin account to use the Tool menu.
2. Click Tool from the top-right side of the screen.
3. Refer to the following sections for instructions on using the Tool options.
4.1 Reset Defaults (Factory Defaults)
This option allows you to reset the cable modem and perform a factory default of the device by clearing all
cached information stored in non-volatile memory. The reset restores the device to the default factory settings
but does not change the current firmware version. The modem registration time to the service provider takes a
few seconds longer than a modem reset since modem must re-scan all frequencies to find its downstream
channels.
1. Access the web interface. Refer to page 12 for instructions if required. Important: You must log in
using the admin account.
3. Click Reset Defaults from the left side of the screen.
Item
Description
Yes/No
Apply
Choose Yes to perform a factory reset. Choose No to not perform a
factory reset. Choose Apply to perform the action selected.
Ubee Interactive
21
4.2 Reset Modem
This option allows you to reset the cable modem just as you would by power-cycling or performing an SNMP
reset of the device. This reset does not perform a factory default. Original primary downstream information is
retained so registration time is faster than the Reset Defaults option.
1. Access the web interface. Refer to page 12 for instructions if required. Important: You must log in
using the admin account.
3. Click Reset Modem from the left side of the screen.
Item
Description
Yes
Choose to perform a reset
No
Choose to not perform a reset
Apply
Choose Apply to perform the action chosen
Ubee Interactive
22

DDM3513 User Guide

Transcription

Similar documents

- Included with Park Millennium Cable TV Package

Motorola SURFboard SB5101 Quick Start Guide

Setup Guide

www.rat-tel.pl

ECONoMIC SKILLS`LAS AnafyZihg Changes ill Qe/`nahd

flyer! - Lm-therm Elektrotechnik AG

REI Wire Strippers

Hywire Install.indd

MXCL-D0135-Maxcell Info Sheet.indd

Step 1: Unplug the Power to your Cable/DSL Internet - D-Link